bi-directional flow rate indicator / … 1 gd eex ia iib/iic t4 t100°c. • explosion/flame proof...
TRANSCRIPT
Features• Ability to detect flow direction with
quadrature signal inputs.• Displays positive and negative flow rate ref.
flow direction.• Total and accumulated total count up and
count down ref. flow direction.• Large 17mm (0.67") digit selection for flow
rate or total.• Selectable on-screen engineering units;
volumetric or mass.• Auto backup of settings and running totals.• Operational temperature -30°C up to +80°C
(-22°F up to 178°F).• Very compact design for panel mount,
wall mount or field mount applications.• Rugged aluminum field mount enclosure
IP67 / NEMA4X.• Intrinsically Safe
II 1 GD EEx ia IIB/IIC T4 T100°C.• Explosion/flame proof II 2 GD EEx d IIB T5.• Full Modbus communication RS232/485/TTL.• Loop or battery powered, 8 - 24V AC/DC or
115 - 230V AC power supply.• Sensor supply 3.2 - 8.2 - 12 - 24V DC.
Signal output• (0)4 - 20mA / 0 - 10V DC according to
positive and/or negative flow rate.• Scaled pulse output according to accumulated
total - count up and count down.• Switch output related to flow direction and
accumulated total.
Signal inputFlow• Reed-switch.• NAMUR.• NPN/PNP pulse.• Sine wave (coil).• Active pulse signals.
Applications• Bi-directional flow measurement applications
like loading / unloading through the sameflowmeter or where undesired backflowdisturbs a correct totalisation.
BI-DIRECTIONAL FLOW RATE INDICATOR / TOTALIZER
WITH ANALOG, PULSE SIGNAL AND FLOW
DIRECTION OUTPUTS
DA
TAS
HE
ET
F11
5 -
BI-
DIR
EC
TIO
NA
LFL
OW
RA
TE I
ND
ICA
TOR
/ T
OTA
LIZ
ER
1
General informationIntroductionThe F115 has been developed for applications
where the direction of flow is an issue. Applications
can be found by loading and unloading of ships
where one bi-directional flowmeter is used. An
other application is the correction of back-flow due
to shocks in a pipeline caused by piston pumps or
valve behavior. It is required to offer two pulse
signals from the flowmeter which are 90° or 240°
degrees out of phase. A wide selection of options
further enhance this models capabilities.
DisplayThe display has large 17mm (0.67”) and 8mm
(0.31”) digits which can be set to show flow rate
and totals. On-screen engineering units are easily
configured from a comprehensive selection. In case
of a reverse flow, the flow rate will be displayed as
a negative value. The totalizers will count down.
ConfigurationAll configuration settings are accessed via a simple
operator menu which can be pass-code protected.
Each setting is clearly indicated with an alpha-
numerical description, therefore avoiding confusing
abbreviations and baffling codes. Once familiar
with one F-series product, you will be able to
program all models in the series without a manual.
All settings and totals are safely stored in EEPROM
memory in the event of sudden power failure.
Analog output signalThe positive and / or negative flow rate is re-trans-
mitted with the (0)4 - 20mA or 0 - 10V DC output
signal. The output signal is updated ten times per
second. The output value is user defined in relation
to the flow rate, e.g. 4mA equals to 0L / Hr and
20mA equals to + or -200L / Hr. The output signal
can be passive, active or isolated where the passive
output type will loop power the F115.
Pulse outputThe scaleable pulse output, reflects the count on the
accumulated display. Moreover, if the transmitted
pulse reflects a count-down situation due to
reverse flow, the second output will be switched.
The pulse length is user defined from 0.008 second
up to 2 seconds. The maximum output frequency
is 64Hz. The output signal can be a passive NPN,
active PNP or an isolated electro-mechanical relay.
Signal inputThe F115 will accept most pulse input signals for
flow or mass flow measurement. To detect the
direction of flow, it is required to offer two signals
90° or 240° out of phase. The input signal types
can be selected for both inputs in the configuration
menu without having to adjust any sensitive
mechanical dip-switches or jumpers. Different
types of sensors are allowed for both inputs.
CommunicationAll process data and settings can be read and
modified manually or through the Modbus
communication link (RS232 / RS485).
Full Modbus functionality remains available for
the Intrinsically Safe version (TTL).
Hazardous areasFor hazardous area applications, this model hasbeen ATEX certified Intrinsically Safe II 1GD EEx ia IIB / IIC T4 T100°C with an allowedoperational temperature of -30°C to +70°C (-22°F to +158°F). A flame proof enclosure is alsoavailable with the rating II 2 GD EEx d IIB T5.
EnclosuresVarious types of enclosures can be selected, all
ATEX approved. As standard the F115 is supplied
in an GRP panel mount enclosure, which can be
converted to an GRP field mount enclosure.
Most popular is our rugged aluminum field
mount enclosure with IP67 / NEMA 4X rating.
Both European or U.S. cable gland entry threads
are available.
Overview application F115
Pulse output Communication linkNegative total output
90º or 270ºout of phase
Analog output
F1152
Dimensions enclosuresAluminum & GRP panel mount enclosure
Aluminum & GRP field / wall mount enclosures
Terminal connections
CB:
RS2
32
CH
: RS4
85 -
2 w
ire
AB
YZ
RX
DT
XD
CT:
TTL
Intri
nsic
ally
Saf
e
P: re
ed s
witc
h / N
PN
P: c
oil
P: n
amur
P: P
NP
P: a
ctiv
e si
gnal
-
+
==
56
PULS
E O
UTP
UT
R1
12
POW
ER S
UPP
LY
GN
D
-+
PD: 8
- 24
V AC
PD: 8
- 24
V D
C
-+
PF: 2
4V A
C
PM: 1
15 -
230V
AC
PF: 2
4V D
C
PD -
XI: 1
6 - 3
0V D
C +-
+
OT:
pas
sive
tran
s.
OA:
act
ive
24V
DC
OR
: mec
h. re
lay
+
==
34
NEG
ATIV
E TO
TAL
OU
TPU
T R
2
1011
FLO
WM
ETER
INPU
T A
9
+
+ -+
+
AP: 4
- 20
mA
AA: 4
- 20
mA
AF: 4
- 20
mA
AU: 0
- 10
V
AI: 4
- 20
mA
AB: 0
- 20
mA
78
ANAL
OG
OU
TPU
T
+II-
+I +U
I U
+II
+II-
+II
OT:
pas
sive
tran
s.
OA:
act
ive
24V
DC
OR
: mec
h. re
lay
+
+
P: re
ed s
witc
h / N
PN
P: c
oil
P: n
amur
P: P
NP
P: a
ctiv
e si
gnal
-1314
FLO
WM
ETER
INPU
T B
12
+
+ -+
+
1819
1715
1627
28
CO
MM
UN
ICAT
ION
/ BA
CKL
IGH
T
2623
2425
2122
2029
3031
DT
R+
12V
CI:
RS4
85 -
4 w
ire
AB
RX
DT
XD
DT
R+
12V
PX: 8
- 30
V D
CO
utpu
t loo
p po
wer
ed u
nit w
ith ty
pe A
P(te
rmin
als
GN
D -
1 - 2
are
not
ava
ilabl
e)
ZB: B
ackl
ight
opt
ion
++
+
PB /
PC: b
atte
ry p
ower
edIn
tern
al lo
ng li
fe L
ithiu
m b
atte
ry(te
rmin
als
GN
D -
1 - 2
are
not
ava
ilabl
e)
(With
PD
/ PF
/ PM
term
inal
s 26
/ 31
are
not
ava
ilabl
e,
bac
klig
ht p
ower
sup
ply
is in
tegr
ated
.)
F115 3
130 mm (5.12")
120
mm
(4.7
2")
31 mm(1.22")
29 mm(1.14")
115 (4.53")
98
(3.8
6")
panel cut-outHB & HC enclosures
75 mm (2.95")
130 mm (5.12")
112 mm (4.40")
60 m
m (2
.36"
)
120
mm
(4.7
2")
M20 x 1,5PG9 PG9
30mm 30mm
22,5
0mm
M20 x 1,5M16 x 1,5 M16 x 1,5
30mm 30mm
22,5
0mm
M20 x 1,5
22,5
0mm
M20 x 1,5 M20 x 1,5
25mm 25mm
22,5
0mm
1/2"NPT
0.9"
1/2"NPT1/2"NPT 1/2"NPT
1.18" 1.18"
0.9"
HA
HM
HN
HO
HD
HP
HE
HT
HF
HU
HG
HZ
HH6 x M12
12mm 12mm
24mm24mm36mm36mm
14m
m17
mm
Ø12
12mm 12mm
24mm24mm36mm36mm
14m
m17
mm
22,5
0mm
30mm 30mm
Ø16 Ø16Ø20
0.9"
Ø22 (0.866")
22,5
0mm
25mm 25mm
Ø20 Ø20
Aluminum GRP
Typical wiring diagram F115-P-(AP)-CH-(OT)-PB Typical wiring diagram F115-P-AP-CH-OT-PX
910
116
5
Common ground
Signal
Supply *
Common ground
TERMINAL CONNECTORSF100 - series
78
Common ground
Flowmeter input type: Ppulse
Circ
uit d
epen
ds o
n ty
pe o
f sig
nal
2827
2629
8 - 30V DC
+
-
A
Common ground
B
*Supply voltage: 1.2 - 3.2V DC to sensor
e.g. indicator
Analog output type AP: passive 4 - 20mA (loop powered)
Modbus communication type CH: RS485 - 2 wire
Pulse output type OT:passive transistor
OUTPUT LOOP POWERED
43Common ground
Switch output type OT:passive transistor
negative total value
Flowmeter input type: Ppulse
1213
14
Common ground
Signal
Supply *
Circ
uit d
epen
ds o
n ty
pe o
f sig
nal
123456e.g. counter
910
11
Common ground
Signal
Supply *
TERMINAL CONNECTORSF100 - series
78
Common ground
Circ
uit d
epen
ds o
n ty
pe o
f sig
nal
2826
29
A
Common ground
B
*Supply voltage: 1.2 - 3.2V DC to sensor
Flowmeter input type: Ppulse
Modbus communication type CH: RS485 - 2 wire
Analog output type AP:(not used in this example)
BATTERY POWERED6
5Common ground
Pulse output type OT: passive transistor
(not used in this example)
1213
14
Common ground
Signal
Supply *
Circ
uit d
epen
ds o
n ty
pe o
f sig
nal
Flowmeter input type: Ppulse
Please note: AP may be used in combination with the
battery!
AP will power the unit (output loop powered);
the battery will be disabled automatically untill power
is disconnected).
43Common ground
Switch output type OT: passive transistor
(not used in this example)
F1154
Typical wiring diagram F115-P-AA-CB-OA-PD Typical wiring diagram F115-P-AI-CI-OR-PM
01
26
5Common ground
TERMINAL CONNECTORSF100 - series
8 - 24V DC
+
-
78
Common ground
Common ground
Main supply
2827
2629
Common ground
*Supply voltage: 1.2 - 3.2 - 8.2 - 12 - 24V DC to sensor
RXD
TXD
DTR12V
8 - 24V AC
Switch output type OA:active 24V DC signal
Analog output type AA:active 4 - 20mAe.g. indicator
+
-
+
-
Earth
Modbus communication type CB: RS232
Power supply type PD: 8 - 24V AC / DC
24V AC / DC POWER SUPPLY4
3Common ground
+
-
Pulse output type OA:active 24V DC signal
negative total value
123456e.g. counter
910
11
Common ground
Signal
Supply *
Flowmeter input type: Ppulse
Circ
uit d
epen
ds o
n ty
pe o
f sig
nal
Flowmeter input type: Ppulse
1213
14
Common ground
Signal
Supply *
Circ
uit d
epen
ds o
n ty
pe o
f sig
nal
01
26
5
TERMINAL CONNECTORSF100 - series
N
78
Common ground
Main supply
26
8 - 30V DC
+
-
Common ground
Earth
L1
Switch output type OR:mechanic relay
e.g. indicator
Power supply type PM:115 - 230V AC
Analog output type AI:passive isolated 4 - 20mA
2831
3029
Y
Z
A
B
Modbus communication type CI: RS485 - 4 wire
115 - 230V AC POWER SUPPLY
*Supply voltage: 1.2 - 3.2 - 8.2 - 12 - 24V DC to sensor
43
123456e.g. counter
negative total value
910
11
Common ground
Signal
Supply *
Flowmeter input type: Ppulse
Circ
uit d
epen
ds o
n ty
pe o
f sig
nal
Flowmeter input type: Ppulse
1213
14
Common ground
Signal
Supply *
Circ
uit d
epen
ds o
n ty
pe o
f sig
nal
F115 5
Hazardous area applicationsThe F115-XI has been ATEX approved byKEMA for use in Intrinsically Safe applications.It is approved according to II 1 GD EEx iaIIB/IIC T4 T100°C for gas and dustapplications with an operational temperaturerange of -30°C to +70°C (-22°F to +158°F).Besides the two I.S. power supply for thepulse and flow-direction outputs, it isallowed to connect up to four I.S. powersupplies in IIB applications or one in IICapplications. Full functionality of the F115remains available, including 4 - 20mA output,pulse and flow-direction outputs andModbus communication (type CT). Powersupply type PD-XI offers a 8.2V sensorsupply e.g. for one Namur sensor. A flameproof enclosure with rating II 2 GD EEx dIIB T5 is available as well. Please contact yoursupplier for further details.
Certificate of conformity KEMA 03ATEX1074 X
TERMINAL CONNECTORSF100 - series
HAZARDOUS AREA SAFE AREA
910
11
Common ground
Signal
Supply *
Circ
uit d
epen
ds o
n ty
pe o
f sig
nal
* Note sensor supply voltage: 1.2V DC for coil sensors or 3.2V DC for other pulse sensors.
Flowmeter input type: Ppulse
Analog output type AP:passive 4 - 20mA
(not used in this example).Common ground 7
8
RXD
Common ground
TXD
2826
29
Modbus communication type CT: TTLPossible for battery powered applications
(not used in this example).
Please note: communciation type CT is not allowed in IIC applications.
DTR+12V
27
Pulse output type OT:passive transistor
(not used in this example).
56
Common ground
Please note: type AP may be used in combination with the battery
(type PC), but only in IIB applications!
AP will power the unit (output loop powered);
the battery will be disabled automatically till power
is disconnected).
Ci is negligiblysmall
34
Common ground
1214
13
Common ground
Signal
Circ
uit d
epen
ds o
n ty
pe o
f sig
nal Supply *
Flowmeter input type: PpulseCi is negligibly
small
F115
Configuration example IIB and IIC F115-P-(AP)-(CT)-(OT)-PC-XI - Battery powered unit
6
Configuration example IIB and IIC - F115-P-AP-(CT)-OT-PX-XI - Output loop powered
TERMINAL CONNECTORSF100 - series
HAZARDOUS AREA SAFE AREA
34
910
1112
1413
Common ground
Common ground
Common ground
Signal
Signal
Supply *
Circ
uit d
epen
ds o
n ty
pe o
f sig
nal Supply *
Circ
uit d
epen
ds o
n ty
pe o
f sig
nal
Analog output type AP:passive 4 - 20mA (output loop powered)
RXD
Common ground
TXD
2826
295
6
Common ground
123456
Ci = 17nF
78
Flowmeter input type: Ppulse
Flowmeter input type: Ppulse
Common ground
DTR+12V
27
e.g. counter
ISOLATOR:I.S. Certified Isolator
TTL to RS232 / RS422 / TTL
For example: MTL5051
+
-
POWER SUPPLYe.g. MTL 5025
and / or REPEATER
e.g. MTL 5042
Uo=max 30V
Io=max 100mA
Po=max 750mW
Uo=max 30V
Io=max 250mA
Po=max 850mW
+
-
+
-
POWER SUPPLYe.g. MTL 5025
or SWITCH INTERFACE
e.g. MTL 5011B
Uo=max 30V
Io=max 100mA
Po=max 750mWe.g. counter
123456
e.g. indicator
+
-
POWER SUPPLYe.g. MTL 5025
or SWITCH INTERFACE
e.g. MTL 5011B
Uo=max 30V
Io=max 100mA
Po=max 750mWe.g. relay
e.g. PC
e.g. indicator
�
Modbus communication type CT: TTLPlease note: communciation type CT is not allowed in IIC applications.
* Note sensor supply voltage: 1.2V DC for coil sensors or 3.2V DC for other pulse sensors.
Pulse output type OT:passive transistor
Ci is negligiblysmall
Ci is negligiblysmall
Ci is negligiblysmall
Ci is negligiblysmall
Switch output type OT:passive transistor
negative total value
F115 7
Configuration example IIB and IIC - F115-P-AF-(CT)-OT-PD-XI - Power supply 16 - 30V DC
TERMINAL CONNECTORSF100 - series
HAZARDOUS AREA SAFE AREA
34
910
1112
1413
Common ground
Common ground
Common ground
Common ground
Signal
Signal
TOTAL Co OF ALL CONNECTEDANALOG APPARATUS IN IICAPPLICATIONS MAY NOT EXCEED 66nF MINUS 17nF
(17nF IS USED BY THE ANALOG OUTPUT SIGNAL TERMINAL 7 + 8).
Supply *
Main supply
Circ
uit d
epen
ds o
n ty
pe o
f sig
nal Supply *
Circ
uit d
epen
ds o
n ty
pe o
f sig
nal
Power supply type PD: 16 - 30V DC (please note: two power supplies PD and battery supply (type PC) is NOT allowed in IIC applications).
Flowmeter input type: Ppulse
Flowmeter input type: Ppulse
RXD
Common ground
TXD
2826
295
6
Common ground
01
2
123456
Ci = 17nF
Analog output type AF:passive floating 4 - 20mA
78
DTR+12V
27
e.g. counter
ISOLATOR:I.S. Certified Isolator
TTL to RS232 / RS422 / TTL
For example: MTL5051
Uo=max 30V
Io=max 250mA
Po=max 850mW
+
-
POWER SUPPLY
For example MTL5025
Uo=max 30V
Io=max 100mA
Po=max 750mW
+
-
+
-
POWER SUPPLYe.g. MTL 5025
or SWITCH INTERFACE
e.g. MTL 5011B
Uo=max 30V
Io=max 100mA
Po=max 750mWe.g. counter
123456
+
-
POWER SUPPLYe.g. MTL 5025
or SWITCH INTERFACE
e.g. MTL 5011B
Uo=max 30V
Io=max 100mA
Po=max 750mWe.g. relay
e.g. PC
e.g. indicator
�
* Note power supply type PD: the supply voltage to pulse sensors is maximum 8.7V (Uo=max 8.7V Io=max 25mA Po=max 150mW) and to analog sensors as connected to terminal 1 (internally linked).
Modbus communication type CT: TTLPlease note: communciation type CT is not allowed in IIC applications.
Due to analog output type AF, the unit has to be powered withwith external power supply type PD.
Pulse output type OT:passive transistor
Control output type OT:passive transistor
Ci is negligiblysmall
Ci is negligiblysmall
Ci is negligiblysmall
Ci is negligiblysmall
negative total value
Note: above values are safety values.Consult the technical specification for operational values.
F1158
Configuration example IIB - F115-P-AP-CT-OT-(PD)-XI - Power supply 16 - 30V DC
TERMINAL CONNECTORSF100 - series
HAZARDOUS AREA SAFE AREA
34
Common ground
Common ground
Main supplyPower supply type PD: 16 - 30V DC
Analog output type AP:passive 4 - 20mA (output loop powered)
RXD
Common ground
TXD
2826
295
6
Common ground
01
2
123456
Ci = 17nF
78
910
1112
1413
Common ground
Common ground
Signal
Signal
Supply *
Circ
uit d
epen
ds o
n ty
pe o
f sig
nal Supply *
Circ
uit d
epen
ds o
n ty
pe o
f sig
nal
Flowmeter input type: Ppulse
Flowmeter input type: Ppulse
Common ground
DTR+12V
27
e.g. counter
+
-
ISOLATOR:I.S. Certified Isolator
TTL to RS232 / RS422 / TTL
For example: MTL5051
+
-
POWER SUPPLYe.g. MTL 5025
and / or REPEATER
e.g. MTL 5042
Uo=max 30V
Io=max 100mA
Po=max 750mW
Uo=max 30V
Io=max 250mA
Po=max 850mW
POWER SUPPLY
For example MTL5025
Uo=max 30V
Io=max 100mA
Po=max 750mW
+
-
POWER SUPPLY
For example MTL5025
Uo=max 30V
Io=max 100mA
Po=max 750mW
+
-
POWER SUPPLY
For example MTL5025
Uo=max 30V
Io=max 100mA
Po=max 750mW
+
-
+
-
POWER SUPPLYe.g. MTL 5025
or SWITCH INTERFACE
e.g. MTL 5011B
Uo=max 30V
Io=max 100mA
Po=max 750mWe.g. counter
123456
e.g. indicator
+
-
POWER SUPPLYe.g. MTL 5025
or SWITCH INTERFACE
e.g. MTL 5011B
Uo=max 30V
Io=max 100mA
Po=max 750mWe.g. relay
e.g. PC
e.g. indicator
�
* Note power supply type PD: the supply voltage to pulse sensors is maximum 8.7V (Uo=max 8.7V Io=max 25mA Po=max 150mW) and to analog sensors as connected to terminal 1 (internally linked).
Modbus communication type CT: TTL
Please note: power supply type PD is not required - unit is output loop powered - type AP.
Pulse output type OT:passive transistor
Control output type OT:passive transistor
Ci is negligiblysmall
Ci is negligiblysmall
Ci is negligiblysmall
Ci is negligiblysmall
negative total value
Note: above values are safety values.Consult the technical specification for operational values.
F115 9
F115
Technical specificationGeneral
DisplayType High intensity reflective numeric and
alphanumeric LCD, UV-resistant.Dimensions 90 x 40mm (3.5” x 1.6”).Digits Seven 17mm (0.67") and eleven 8mm (0.31") digits.
Various symbols and measuring units.Refresh rate User definable: 8 times/sec. - 30 secs.Option ZB Transflective LCD with green LED backlight.
Good readings in full sunlight and darkness. Note Only available for safe area applications.
Operating temperatureOperational -30°C to +80°C (-22°F to +178°F).Intrinsically Safe -30°C to +70°C (-22°F to +158°F).
Power requirementsType PB Long life Lithium battery - life-time depends upon
settings and configuration - up to 5 years.Type PC Intrinsically Safe long life lithium battery - life-time
depends upon settings and configuration - up to 5 years.
Type PD 8 - 24V AC / DC ± 10%. Power consumption max. 10 Watt. Intrinsically Safe: 16 - 30V DC; power consumption max. 0.75 Watt.
Type PF 24V AC / DC ± 10%. Power consumption max. 15 Watt.Type PM 115 - 230V AC ± 10%. Power consumption max. 15 Watt.Type PX 8 - 30V DC. Power consumption max. 0.5 Watt. Type ZB 12 - 24V DC ± 10% or type PD / PF / PM.
Power consumption max. 1 Watt.Note PB/PF/PM Not availble Intrinsically Safe.Note PF/PM The total consumption of the sensors and outputs
may not exceed 400mA @ 24V.Note For Intrinsically Safe applications, consult the safety
values in the certificate.
Sensor excitationType PB/PC/PX 3.2V DC for pulse signals and 1.2V DC for coil pick-up.
Note This is not a real sensor supply. Only suitable for sensors with a very low power consumption like coils(sine wave) and reed-switches.
Type PD 1.2 - 3.2 - 8.2 - 12 and 24V DC - max. 50mA @ 24V DC.Type PD-XI 1.2 - 3.2 - 8.2V DC - max. 7mA @ 8.2V DC and mains
power supply voltage (as connected to terminal 1).Type PF / PM 1.2 - 3.2 - 8.2 - 12 and 24V DC - max. 400mA @ 24V DC.
Terminal connectionsType Removable plug-in terminal strip.
Wire max. 1.5mm2 and 2.5mm2.
Data protectionType EEPROM backup of all settings. Backup of running
totals every minute. Data retention at least 10 years.Pass-code Configuration settings can be pass-code protected.
Hazardous areaIntrinsically Safe ATEX approval ref.: II 1 GD EEx ia IIB/IIC T4 T100°C.Type XI Maximum ambient +70°C (158°F).Explosion proof ATEX approval ref.: II 2 GD EEx d IIB T5.Type XF Dimensions of enclosure: 300 x 250 x 200mm
(11.8” x 9.9” x 7.9”) L x H x D.Weight appr. 15 Kg.
EnvironmentElectromagnetic Compliant ref: EN 61326 (1997), EN 61010-1 (1993).compatibility
CasingGeneralWindow Polycarbonate window.Sealing Silicone.Control keys Three industrial micro-switch keys. UV-resistant
silicone keypad. Option ZS Silicone free ABS enclosure with EPDM and PE
sealings. UV-resisitant polyester keypad. Note This option comes with type HD only.
Aluminum wall / field mount enclosuresGeneral Die-cast aluminum wall/field mount enclosure IP67 /
NEMA 4X with 2-component UV-resistant coating.Dimensions 130 x 120 x 75mm (5.12" x 4.72" x 2.95") - W x H x D.Weight 1064 gr.
Type HA Cable entry: 2 x PG9 and 1 x M20. Type HM Cable entry: 2 x M16 and 1 x M20. Type HN Cable entry: 1 x M20. Type HO Cable entry: 2 x M20. Type HP Cable entry: 6 x M12. Type HT Cable entry: 1 x 1/2" NPT.Type HU Cable entry: 3 x 1/2" NPT.Type HZ Cable entry: no holes.
GRP wall / field mount enclosuresGeneral GRP wall/field mount enclosure IP67 / NEMA 4X,
UV-resistant and flame retardant. Dimensions 130 x 120 x 75mm (5.12" x 4.72" x 2.95") - W x H x D.Weight 566 gr.
Type HD Cable entry: no holes.Type HE Cable entry: 2 x Ø 16mm and 1 x Ø 20mm.Type HF Cable entry: 1 x Ø 22mm (0.866").Type HG Cable entry: 2 x Ø 20mm. Type HH Cable entry: 6 x Ø 12mm.
Panel mount enclosuresDimensions 130 x 120 x 60mm (5.12" x 4.72" x 2.36") - W x H x D.Panel cut-out 115 x 98mm (4.53" x 3.86") L x H.
Type HB Die-cast aluminum panel mount enclosure IP65 / NEMA 4.
Weight 570 gr.Type HC GRP panel mount enclosure IP65 / NEMA 4,
UV-resistant and flame retardant.Weight 422 gr.
10
F115
Signal inputsFlowmeterType P Coil / sine wave (minimum 20mVpp or 80mVpp -
sensitivity selectable), NPN/PNP, open collector, reed-switch, Namur, active pulse signals 8 - 12 and 24V DC.
Note Different sensor types can be used for both inputs.Frequency Minimum 0Hz - maximum 7kHz for total and flow rate.
Maximum frequency depends on signal type and internal low-pass filter. E.g. reed switch with low-pass filter: max. frequency 120Hz.
K-Factor 0.000010 - 9,999,999 with variable decimal position.Low-pass filter Available for all pulse signals.Option ZF coil sensitivity 10mVpp.
Signal outputsAnalog outputFunction Transmitting positive (and negative) flow rate.Accuracy 10 bit. Error < 0.05%. Analog output signal can be
scaled to any desired range.Update time Ten times per second.Type AA Active 4 - 20mA output (requires OA + PD, PF or PM).Type AB Active 0 - 20mA output (requires OA + PD, PF or PM).Type AF Passive floating 4 - 20mA output for Intrinsically
Safe applications (requires PC or PD).Type AI Passive galvanically isolated 4 - 20mA output - also
available for battery powered models (requires PB, PD, PF or PM).
Type AP passive 4 - 20mA output - not isolated. Unit will beloop powered.
Type AU Active 0 - 10V DC output (requires OA + PD, PF or PM).
Pulse outputFunction Pulse output and indication negative totalisation. Frequency Max. 64Hz. Pulse length user definable between
7.8 msec up to 2 seconds.Type OA Two active 24V DC transistor outputs (PNP);
max. 50mA per output (requires AA + PD, PF or PM).Type OR Two electro-mechanical relay outputs (N.O.) - isolated;
max. switch power 230V AC - 0.5A per relay (requires PF or PM).
Type OT Two passive transistor outputs (NPN) - not isolated. Load Max. 50V DC - 300mA per output.Note Output 2 is switched in case a negative acc. total
is transmitted.
Communication optionFunction Reading display information, reading / writing all
configuration settings.Protocol Modbus RTU.Speed 1200 - 2400 - 4800 - 9600 baud.Addressing Maximum 255 addresses.Type CB RS232Type CH RS485 2-wire Type CI RS485 4-wireType CT TTL Intrinsically Safe.
OperationalOperator functionsDisplayed • Positive and negative flow rate.functions • Total and accumulated total (count up and down).
• Total can be reset to zero by pressing the CLEAR-key twice.
TotalDigits 7 digits.Units L, m3, GAL, USGAL, KG, lb, bbl, no unit.Decimals 0 - 1 - 2 or 3. Note Total can be reset to zero.
Accumulated totalDigits 11 digits.Units / decimals According to selection for total.Note Can not be reset to zero.
Flow rateDigits 7 digits.Units mL, L, m3, Gallons, KG, Ton, lb, bl, cf, RND, ft3, scf,
Nm3, Nl, igal - no units.Decimals 0 - 1 - 2 or 3.Time units /sec - /min - /hr - /day.
Display example - 90 x 40mm (3.5” x 1.6”)
11
Specifications are subject to change without notice.
Ordering information Standard configuration: F115-P-AP-CX-HC-OT-PX-XX-ZX.Ordering information: F115 -_ -A _ -C _ -H _ -O _ -P _ -X _ -Z _Flowmeter input signalP Pulse input: coil, npn, pnp, namur, reed-switch.Analog output signalAA Active 4 - 20mA output - requires OA + PD, PF or PM.AB Active 0 - 20mA output - requires OA + PD, PF or PM.AF I.S. floating 4 - 20mA output - requires PC or PD.AI Isolated 4 - 20mA output - requires PB, PD, PF or PM.AP Passive 4 - 20mA output, loop powered unit.AU Active 0 - 10V DC output - requires OA + PD, PF or PM.CommunicationCB Communication RS232 - Modbus RTU.CH Communication RS485 - 2-wire - Modbus RTU.CI Communication RS485 - 4-wire - Modbus RTU.CT Intrinsically Safe TTL - Modbus RTU.CX No communication.Panel mount enclosures - IP65 / NEMA4HB Aluminum enclosure.HC GRP enclosure.GRP field / wall mount enclosures - IP67 / NEMA4XHD Cable entry: no holes.HE Cable entry: 2 x 16mm flow rate 1 x 20mm.HF Cable entry: 1 x 22mm (0.866”).HG Cable entry: 2 x 20mm.HH Cable entry: 6 x 12mm.Aluminum field / wall mount enclosures - IP67 / NEMA4XHA Cable entry: 2 x PG9 flow rate 1 x M20.HM Cable entry: 2 x M16 flow rate 1 x M20.HN Cable entry: 1 x M20.HO Cable entry: 2 x M20.HP Cable entry: 6 x M12.HT Cable entry: 1 x 1/2”NPT.HU Cable entry: 3 x 1/2”NPT.HZ Cable entry: no holes.OutputsOA Two active transistor outputs - requires AA, AB or AU and PD, PF or PM.OR Two mechanical relay outputs - requires PF or PM.OT Two passive transistor outputs - standard configuration.Power supplyPB Lithium battery powered.PC Lithium battery powered - Intrinsically Safe.PD 8 - 24V AC/DC + sensor supply - with XI: 16 - 30V DC.PF 24V AC/DC + sensor supply.PM 115 - 230V AC + sensor supply.PX Basic power supply 8 - 30V DC (no real sensor supply). Unit requires external loop AP.Hazardous areaXI Intrinsically Safe.XF EExd enclosure - 3 keys.XX Safe area only.Other optionsZB Backlight. ZF Coil input 10mVpp.ZS Silicone free ABS enclosure with EPDM and PE sealings (type HD only).ZX No options.
The bold marked text contains the standard configuration.
Available Intrinsically Safe.
FLUIDWELL bvP.O. Box 65460 AA - Veghel - The NetherlandsTel.: +31 (0)413 343786Fax.: +31 (0)413 [email protected] Internet: www.fluidwell.com C
opyr
ight
: Flu
idw
ell b
v -
2006
- F
WD
SF11
5-12
06-E
N
12