best-kept-secret.pdf
TRANSCRIPT
-
8/14/2019 best-kept-secret.pdf
1/3
THE BEST KEPT SECRET:
A TREASURE HUNTERS GUIDE
Pro Tips Stories and FactsforMetal Detectorists
3 Quick Detector Tips
QUICK FACT!
Tarnished coins can be more valuable than
dipped coins. See page 3 for more fun facts
about metal and coins!
Tuning Tips From the LivingLegend
1) Consider purchasing acoil cover,which will
protect the coil from
possible damage.
2) High levels of salt cansometimes interfere with
your detectors signal.Lower your detectors
sensitivity level to stabilize
readings.
3) Invest in a pinpointer.Thiswill not only speed up
your recovery time, but
also prevent damaging
your target.
1
Sometimes it takes time and strategy to get the most out of
your metal detector. Tuning your detector is crucial in
increasing your odds in finding your target and could be the
missing puzzle piece in your treasure hunting strategy. Stu
Auerbach, owner of Kellyco Metal Detectors and long time
metal detecting hobbyist, suggests a great method in,
addition to factory instructions, to
ensure your metal detector is
working at its top capability.
When your metal detector is set
on all metals, your detector willlook for any kind of metallic
object in the soil, such as bottle
caps, tins, and nails. In order to
get around this, increase your
discrimination, which will limit your
depth, but will help filter out
undesirable finds, and also
decrease your sensitivity control.
Once you have adjusted your
machine, the real test begins.
In order to get started, you will need some metal samples orpieces. Try to pick an object similar to what you would like tofind while detecting.
Continue reading on page 2
-
8/14/2019 best-kept-secret.pdf
2/3
2
Tuning TipsContinued from Page 1
Picture this: yo
are strolling along
with your meta
detector jus
waiting to find
something . .
and then
happens! Unarguably, searching for you
target is one of the most exciting aspects o
metal detectingyou never know wha
could be causing your detector to signala
diamond ring, valuable coin, or just a littlepiece of yesterday. Of course, in order to
learn whats under the ground, you will have
to dig! To a metal detectorist, digging a hol
is like scienceit must be neat and exact o
the instability might just cause chaos, that is
a big mess of dirt surrounded by a wel
manicured patch of green grass.
Part of the responsibility of metal detecting i
ensuring that the area you disturb while
Should you clean discovered coins?
Value often dictates the necessity to clean your
coins. If the coin in question is considered
valuable and sought after by collectors, no
attempts should be made to clean the coin.
Several methodologies and beliefs regarding
best practices exist regarding coin cleaning.
Because certain techniques can sometimes do
more harm than good, any urge to shine up an
old penny should be avoided. And the old, but
often times dead-on, clich, Beauty is in the
eye of the beholder, is true in the minds of coin
collectors. A nice patina or tarnish may actually
be preferred over a restored shine.
If you cant resist the urge to clean or just
enjoy a shiny finish on your personal
collection, try these easy tips:
Soak your coins in distilled water andthen freeze. As the ice crystals form, the dirt
will expand and detach from the coin. This
method may need to be repeated several
times.
Apply any standard white glue to the
surface of the coin and peel off once dried.
Cover a copper penny in ketchup, scrub,
and rinse. Mix baking soda with water to
form a paste and rub the mixture on the
penny to return its shine!
For example, if silver coins are your concentration,
take a recovered or replica coin and bury one at
approximately thirty inches. Make sure you mark
your coin in order to guarantee easy recovery.
You can do this by tying a piece of string around
the object and burying with the untied end of the
string still exposed on the surface. By doing this,the string acts as a direct guide to your target.
Once your target is buried, move your detector
over the area to see if it detects your buried
object. If your detector does not indicate a find,
try reburying the object at a shallower level in
order to determine readable depth. If yourdetector does sound, it is time to dig a deeper
hole and bury your target once again in order to
test the detectors limit. When retesting, try
increasing or decreasing the depth of your hole
by five inches during each trial. Ultimately, this test
allows you to determine the level of depth your
detector is still successfully finding particulartargets.
By following these easy steps, you will not only be
more familiar with the signals your detector is
emitted, but also heighten your awareness ofyour detectors potential.
Pro Tip:ReachingYour Targ
Continue reading on page 3
-
8/14/2019 best-kept-secret.pdf
3/3
3
Pro TipsContinued from Page 2
Not all types of corrosion are equal
For instance, the development of rust
on iron often has devastating effects
The development of rust
compromises the integrity of the iron
causing pits, cracking, and the
overall deterioration of the metal
Rust usually develops when iron is
exposed to moisture
and oxygen over anextended period o
time; the process is
expedited by the
exposure of salt
water.
Tarnish is another form of corrosion
Unlike rust, tarnish usually affects the
top layer of silver and does not
compromise the overall structure. To
a collector, tarnish does notnecessarily devalue a find, but
actually serves as protection. A
polished or cleaned coin may
actually decrease the value of the
coin by approximately fifty percent
Tarnish may also be referred to as
toning when the film develops ove
a long period of time.
The Smart Collector:
Metal, Age, and Its
Effects
digging or searching is left with as little damage as
possible and cleaner than how you found it. In order
to achieve this, one must be systematic in their
technique.
With a dulled flat-tip screwdriver or latex wand,
attempt to estimate the depth of the target in order
to determine the dimensions of the plug of soil you
will need to dig. In order to avoid scratching or
damaging your target, make sure your probe has
blunted edges.
Your probe can
double as another
tool used to
extract the target
from shallow soil.Next, using any
kind of hunting
knife or cutting
tool, cut a
rectangle in the
soil, but be sure to leave the fourth side of the
rectangle intact and uncut. The uncut area will act
as a hinge when attempting to remove the soil
without complete detachment. If you cannot avoid
detachment, make sure to have a drop cloth or a
round plastic piece (like a Frisbee or even a flexibleplastic kitchen cutting board) available for easy soil
transfer when complete. Once you have your plug
of dirt unearthed, wave your detector or pinpointer
over the plug to see if the target is in the plug or if
deeper digging is necessary. After you have found
your treasure, place your new piece safely away in a
storing deviceof your choice, such as a fanny pack,
finds apron, or back pack, and replace the plug of
dirt by simply laying down your plug or using yourplastic disk to replace the dirt.
Having a systematic plan for extracting your treasure
will not only decrease frustration, but will save time
and open up your day for more treasure hunting!
Written and designed by Keri-Anne Tessitore
Brought to you by