bellofram tranductor type 1500 orden code

7/27/2019 Bellofram Tranductor Type 1500 Orden Code

1/5

www.marshbellofram.com 800.727.5646

Type 1500 Description

The T-1500 is a new series o electro-pneumatic

transducers that convert an electrical signalto a proportional pressure output. It providesprecision electro-pneumatic control to actuators,

valves, positioners, fnal control elements andis ideally used or high-ow control devices.The Type 1500's compact size and accessibilityto ports and adjustments allow the unit to be

installed in space-constrained locations or in amaniold or multi-device control.

DIN rail and maniold assemblies are available

in kits that provide three, fve or ten mountingpoints.

An integral pneumatic volume booster is in-cluded in the Type 1500 design to provide high

ow capacity. (See specifcations or ow data.)

Standard Features

Small ootprint, compact size

Maniold mounting confgurations

Built-in volume booster

Electrical Connections: Conduit 12 NPT or

BSPT, Terminal Block, HirschmannConnectors (DIN 43 650-A)

Supply and output ports on

ront and back o unit

Low air consumption

External zero and span adjustments

Low cost

Field accessible orifce

Electrical conduit connectionmeets CE requirements

Options Available

Intrinsically Sae (FM, CSA, ATEX)

NEMA 4X (FM, CSA) Excludes Terminal Block

Applications

The T-1500 transducer can be used as an

electro-pneumatic control device to operate:

Valve actuators

Valve positioners

HVAC systems

Material handling systems

Paper handling controls

Automation systems

Liquid and gas processing systems

Type 1500I/P & E/P Transducers

Principle of Operation

(See Fig. 2 and 6) The T-1500 Transducer

is a orce balance device in which a coil issuspended in the feld o a magnet by a exure.Current owing through the coil generates axial

movement o the coil and exure. The exuremoves against the end o a nozzle and createsa back pressure in the nozzle by restricting airow. This back pressure acts as a pilot pressure

to an integral booster relay. Consequently, asthe input signal increases (or decreases orreverse acting), output pressure increasesproportionally.

In the zero based T-1500, the output o thetransducer section is routed to an integral nega-tive bias booster relay. The bias relay allows the

complete unit to regulate output pressure downto 0 psig/BAR. The bias relay also amplifes theoutput o the transducer which allows the zerobased units to regulate higher output pressures

than the standard T-1500.

Zero and Span are calibrated by turning easilyaccessible adjusting screws on the ront ace

o the unit (see Figures 3, 4, 5, 7, 8 and 9).The zero adjustment causes the nozzle to moverelative to the exure. The span adjustment isa potentiometer that limits the ow o current

through the coil. A thermistor circuit in serieswith the coil provides temperature compensa-tion.

Mounting

The T-1500 can be mounted at any anglebut should be calibrated ater mounting. Formaximum output pressure stability, the T-1500

should be mounted vertically in a vibration reelocation or such that the vibration is isolatedto the X and Z axis. The T-1500 can be in-line,

panel, pipe, DIN rail or maniold mounted.

Air Connections

1. Supply Air must be instrument quality air

regulated between 5 PSI above maximumoutput pressure up to 120 PSIG / 8.3 BAR(See table: Supply Pressure Range).

2. Instrument-quality air consists o:

a. A dew point less than 35Fb. No particles larger than three micronsc. Maximum oil content o 1 ppm

3. All unused ports must be plugged.

Type 1500Transducers

Supply

Connect supply to either o two ports marked

IN on the base o the transducer. Avoid get-ting pipe sealant inside the piping or transducer.

Output

Connect output to either o two ports markedOUT on the base o the transducer. Thesecond OUT port may be used or a pressure

gauge.


2/5

8 800.727.5646 www.marshbellofram.com

Type 1500 Transducers

Standard Range Zero Based

Hysteresis


3/5


T-1500 Manifold and Adapter Kit

Principle of Operation

The T-1500 maniold assembly allows multipleT-1500 Transducers to be mounted in parallel.This minimizes the number o individual supply

air lines required. Maniolds are available tohold three, fve, or ten units. Each maniold

comes with check valves so that a unit can bepulled o o the maniold or service or replace-

ment without aecting the whole maniold.(See Figure 1.)

Mounting

The maniolds may be mounted ush with awall or cabinet or may be mounted away romthe wall. Both mounting options are included in

the basic maniold kit. In addition, all fttingsrequired to mount the ull number o units ineach maniold are included in the basic kit. Anadditional adapter kit may be purchased which

contains all o the hardware required to mani-

old mount a single T-1500 Transducer shouldthe need arise.

Air Supply Attachment

The air supply can be at tached to either sideo the maniold via a 3/4 NPT connection orto the back o the maniold via a 3/8 NPT con-

nection. Ater an air supply port is selected, theopen ports should be plugged using the plugsprovided with the maniold kit and a pneumatic

sealant.

Output Air Attachment

Connect the output ports rom each o the

T-1500 Transducers to the bottom or back othe maniold. Ater connecting the transducers,plug the other 1/8 NPT ports using the plugsprovided and a pneumatic sealant.

T-1500 Manifold Adapter Kit

The T-1500 maniold kit includes the adapter

kits required or each transducer.

Electrical Connections

Two brackets supplied with the maniold kit

allow an electrical conduit to be attached tothe maniold. Mounting screws and nuts areprovided, and the brackets have an 11/64"

diameter hole which will ft standard 8-36 UNFor 8-32 UNC screws (not supplied).

ADAPTER PLATECAPTIVE SCREW

T1500

TRANSDUCER

Z

S

INOUT

CHECK VALVESB

A

2.50"

63.5mm

3.50"

88.9mm

Figure 1 - Manifold Front View

Type 1500 Dimensions

Number oTransducers

Length A Length B

37.57"

192.3 mm

6.83"

173.5 mm

510.75"

273.1 mm

10.01"

254.3 mm

1018.70"

475.0 mm17.96"

456.2 mm

Type 1500 Manifold Ordering InformationKit Part Number

T-1500 Wall Mount Kit, 3 unit 010-606-000



T-1500 Maniold Adapter Kit (Replacement) 010-602-000

DIN Rail Mounting Kit 971-140-000

Pneumatic Repair Kit

(3-15, 3-27 PSIG / 0.2-1.0, 0.2-1.9 BAR)971-141-000


(6-30 PSIG / 0.4-2.1 BAR)971-141-002

Pneumatic Repair Kit, Fluorocarbon

(3-15, 3-27 PSIG / 0.2-1.0, 0.2-1.9 BAR)

971-141-003

Pneumatic Repair Kit, Fluorocarbon(6-30 psig / 0.4-2.1 BAR)

971-141-004


(0-120 PSIG / 0-8.3 BAR)971-145-000

Pneumatic Repair Kit Fluorocarbon,

(0-120 psi / 0-8.3 BAR)971-145-001

Electronic Repair Kit (4-20 mA) 971-142-000

Electronic Repair Kit (0-5 VDC or 1-5 VDC) 971-142-001

Electronic Repair Kit (1-9, 1-10 VDC, or 0-10 VDC) 971-142-002

2" Pipe Mounting Kit 971-159-000

Filter Kit, 60 Micron 010-139-000


4/5

0 800.727.5646 www.marshbellofram.com

Type 1500 Extended Range Parts

Number Description

1 Circuit Board

2 Worm Gear

3 Duckbill Valve (NEMA 4X Only)

4 Magnet Assembly

5 Nozzle Assembly6 Bonnet Gasket (NEMA 4X Only)

7 Servo Diaphragm (I/P Section)

8 Control Diaphragm (I/P Section)

9 Pintle

10 Supply Seat

11 Coil/Flexure Assembly

12 Servo Diaphragm (Bias Relay)

13 Control Diaphragm (Bias Relay)

14 Orifce Screw

15 Bias Spring

Figure 2: Type 1500 Extended Range Parts

Figure 3: Terminal Block

IN

IN

OUT

OUT

Z SPANADJUSTMENT

ORIFICE

SCREW

ZERO

ADJUSTMENT

S

2.87"

62.9mm

5.27"

133.9mm

2.25"

57.2mm

Back Dimensions

IN

OUT IN

OUT

10-32 UNF-2B

MOUNTING

HOLES

3.51"

89.2mm

2.01"

51.1mm

0.52"

13.22mm

1.00"

25.4mm

1.52"

38.6mm

0.77"

19.6mm

Figure 4 - Hirschmann(DIN 43 650-A)

IN

IN

OUT

OUT

TERMINAL "2" TERMINAL "1"

SAFETYGROUND

SPANADJUSTMENT

SZ

ZERO

ADJUSTMENT

ORIFICE

SCREW

5.27"

133.9mm

2.77"

70.4mm

2.25"

57.2mm

FIGURE 5: 1/2 NPT / BSPT

2.25"

57.2mm

SPAN

ADJUSTMENT

S

ZEROADJUSTMENT

ORIFICESCREW

Z

IN

IN

OUT

OUT

5.27"

133.9mm

3.16"

80.3mm

Drawings and dimensions are or reerence only.

Type 1500 Extended Range Dimensions


5/5


Type 1500 Standard Range Parts

Number Description

1 Circuit Board

2 Worm Gear

3 Duckbill Valve (NEMA 4X Only)

4 Magnet Assembly

5 Nozzle Assembly

6 Bonnet Gasket (NEMA 4X Only)

7 Servo Diaphragm (I/P Section)

8 Control Diaphragm (I/P Section)

9 Pintle

10 Supply Seat

11 Coil/Flexure Assembly

Figure 6: Type 1500 Standard Range Parts

Figure 7: Terminal BlockBack Dimensions

Figure 9: Hirschmann(DIN 43 650-A)

Type 1500 Standard Range Dimensions

FIGURE 8: 1/2 NPT / BSPT

INOUT

1.52"38.6mm

1.00"25.4mm

10-32 UNF-2B

MOUNTING HOLES

0.77"19.6mm

2.01"51.1mm

0.52"13.2mm

ZEROADJUSTMENT

ORIFICESCREW

2.25"

57.2mm

SPANADJUSTMENT

SZ

INOUT

3.77"

95.8mm

2.87"

72.9mm

2.25"

57.2mm

SPANADJUSTMENT

3.77"

95.8mm

3.16"

80.3mm

ZEROADJUSTMENT

ORIFICESCREW

SZ

INOUT

ZEROADJUSTMENT

ORIFICESCREW

2.25"

57.2mm

SPANADJUSTMENT

3.77"

95.8mm

2.77"

70.4mm

SZ

OUT IN

Agency Approvals - Applies only to units ordered with approvals

Vibration Axes

Y

X

Z

Drawings and dimensions are or reerence only.

Factory Mutual

T-1500 I/P and E/P TransducersIntrinsically Safe:ClassI,Division1,GroupsA,B,C,&D,T4Ta=70C;Entity;

Non-Incendive:ClassI,Division2,GroupsA,B,C,&D,T4Ta=70C

Dust-Ignition Proof:ClassesII&III,Division1,GroupsE,F,&G,T4Ta=70C

Suitable:ClassesII&III,Division2,GroupsF&G,T4Ta=70CType4XNEMA 4XEntity Parameters: V

Max=30Vdc,I

Max=100mA,C

i=0F,L

i=0mH.

Canadian Standards Association

T-1500 I/P Transducers Hazardous Locations: Class I, Division 2,

Groups A, B, C, & D; Type 4X NEMA 4X:

I/P transducer, rated VMax=30Vdc,I

Max=100mA.TempCodeT4.Maxambient70C.

IN COMPLIANCE WITH STD C22.2 No 213.

Intrinsically Safe, Entity - Hazardous Locations: Class I, Groups A, B, C, & D;

Class II, Group E, F, & G; Class III; Type 4X NEMA 4X:

I/P transducer. Entity Parameters: VMax=30Vdc,I

Max=100mA,C

i=0,L

i=0.IntrinsicallySafe

when connected per Installation Instruction 010632. Temp Code T4. Max ambient 70C.

ATEX

Intrinsically safeforII1GEExiaIIBT4Tamb=-20to65C

Input Parameters: VMax=30V,Pi=1W,Ii=100mA,Req=180OHMS,

Ci=0,L

i=24mH

Models are CE marked or use in the European Union, and meet the EMC

heavy machinery directives.

The Belloram T-1500 Transducers were tested and ound to comply with

Electromagnetic Compatibility Directive eective January 1, 1996.

The relevant EMC specifcations tested were the ollowing: EN 50081-1

(1992) and EN 50082-1 (1992). A Technical Construction File, Serial #107

was written and Certifcate o Conormity issued by a Competent Body

bellofram tranductor type 1500 orden code

Documents