beam column chen jcsr 1991
TRANSCRIPT
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 1/40
J. Co nstruct. Steel Researc h 18 (1991) 269-308
B e a m - C o l u m n D e s i g n i n S te e l F r a m e w o r k s - -I n s i g h t s o n C u r r e n t M e t h o d s a n d T r e n d s
J . Y . R i cha r d L i e w , D . W . W h i te & W . F . C h e nStructural E nginee ring D epa rtme nt, School of Civil Engineering, Purd ue U niversity, W est
Lafa yette, Indiana 47907, U SA
(Rece ived 20 Septem ber 1990; revised version received and accep ted 13 February 1991)
A B S T R A C T
The f i rs t par t o f the pa per describes the back grou nd behind the develop-
m e n t o f the curren t A IS C -L R F D beam -co l um n in te raction equa ti ons . Th i s
is f o l l ow ed by a r igorous eva l ua t ion o f the L R F D procedures w i th a
spec if ic foc us on the use o f e f fec ti ve l ength fac tors fo r beam -column design .
Va rious me thod s o f co m pu t ing effective length factors are reviewed, an d
characteris tic values obtained f r o m the di f ferent m ethod s are dem ons -
trated. Co m pa rison s are m ad e be tween ul t imate s trength curves repre-sen ted by the LRFD beam-column equat ions and s t rength curves com-
pu ted by sec ond -orde r inelastic analysis . Last ly , the pro cedu re in the
current Canadian S tandard C SA-S1 6.1-M 89, which does no t involve the
use o f e f fec ti ve l engt h f act ors , is pos ed i n L R F D f o rm a t an d com pared t o
the current L R F D metho d , which requires the use o f K fac tors . The goal is
to i llustrate the quali ties an d l imi tat ions o f both types o f design approaches.
N O T A T I O N
A F G e n e r a l t e r m f o r m o m e n t a m p l i f i ca t i o n f ac t o r s
B1 P - 6 m o m e n t a m p l i f i c a t i o n f a c t o r in L R F D ~,
Cm
B 2 P - ~ m o m e n t a m p l i f i c a t io n f a c t o r ,
1/ "oh no qn o,L X
1 - po \ /,H L269
J. Co nstruct. Steel Research 0143-974X/91/$03.50t~) 1991 Elsevier Science Pub lishers L td ,Eng land. Prin ted in G reat Bri tain
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 2/40
270 J. Y. Richard Liew, D. W. White, W. F. Chen
C~EE,
G, GA, GB
H/b,/~K
L
Lb, Lc
M~t
Mnt
Mp
g uM~x, Muy
P c l "
Be
eek
Pea
P .
e .e~r
( equ iva len t to - U2 of Sec t ion 8 .6 .1 , CSA -S 16 .12) o r
1( XPu ) i n e q n ( H 1 - 6 ) o f L R F D ( n o t a l lo w e d
1 - EP,'--"~ in CSA -S16 .12)
E q u i v a l e n t u n i f o r m m o m e n t f a c t o r fo r b e a m - c o l u m n s
M o d u lu s o f e l a s t ic i ty , a s su med eq u a l t o 2 0 0 0 0 0 N /m m 2
C o l u m n t a n g e n t m o d u lu s
R a t io o f t h e b en d in g s t if fn es s o f t h e co lu m n s v e rsu s t h a t o f t h e
b eams a t a b eam- co lu mn jo in t ( su b sc r ip t s ap p ly t o t h e
r e sp ec t iv e en d s o f t h e co lu m n )
H o r i zo n ta l f o r ce a t a f r am e f lo o r l ev e lM o m e n t o f in e r t ia o f t h e b e a m a n d c o l u m n c r o ss -s e ct io n s
E f f ec t i v e len g th f ac to rA c t u a l l en g t h o f a m e m b e r
A c t u a l l e n g th s o f b e a m s a n d c o l u m n s
M a x i m u m m o m e n t i n t h e m e m b e r c a u s e d b y l a t e ra l tr a n s la -
t ion o f the s to ry , ca lcu la ted by a f i r s t -o rder e last ic ana lys i s
M a x i m u m m o m e n t i n t h e m e m b e r a s s u m in g n o s t o ry tr a n s la -
t ion , ca lcu la ted b y a f i r s t -o rder e las tic ana lys isPlas t ic c ross - sec t ion bend ing c apac i ty
R eq u i r ed f l ex u r a l s t r en g th w i th in th e l en g th o f a me m b er
M a x i m u m s e c o n d - o r d e r el a st ic m o m e n t w i th i n th e l e n g t h o f a
m em b er ab o u t t h e s t r o n g an d w eak ax es o f th e c r o s s - sec t io n ,
r espec t ive ly
T h e e l a st ic b u ck l in g l o ad f r o m a b u ck l in g an a ly s isT h e E u le r b u ck l in g l o ad , ,rr2 EFL2
Elas t ic b uck l ing lo ad , 7 r2EI/(KL) 2, based on a va lue o f Ko b t a i n e d f r o m t h e a l i g n m e n t c h a r tE la s t i c b u ck l in g l o ad o f co lu mn i , , x 2 E I i / ( K i L i ) 2 , w i th K i
ca l cu l a t ed f r o m L eMessu r i e r ' s f o r mu la o r t h e mo d i f i ed K
f a c t o r f o r m u l a
N o m i n a l a x i a l c o m p r e s s i v e s t r e n g t h b a s e d o n t h e L R F Dc o l u m n s t re n g t h e q u a t i o n s ,Py(0.658~J) for A c - 1.5 or
R e q u i r e d a x ia l s t re n g t h f o r t h e m e m b e r u n d e r c o n s i d e r a t io n
A x ia l lo ad a t f u l l -y i e ld co n d i t i o n , i. e . , t h e sq u ash lo ad
R a d i u s o f g y r a t i o n
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 3/40
Beam -column design in stee l rame wo rks 271
a
Aoh
8
3'A ¢
AfA ~
(I)
O ' ~ c
%
L o a d r a t io b e t w e e n a d j a c e n t fr a m e d c o l u m n s
Fi r s t -o rder in t e r - s to ry def l ec t ion
D e f l e c t io n a s so c i a te d w i t h m e m b e r c u r v a t u re , m e a s u r e d f r o m
t h e m e m b e r c h o r dL e n g t h r a ti o b e t w e e n a d j a c e n t f ra m e d c o l um n s
No r m a l i zed co l u m n s l en d e r n es s r a t io ( KL / ,r r ) X / ~y /E
F r a m e b u c k l in g lo a d f a c t o r
S t o r y b u ck l i n g l o ad f ac t o r
L R F D r es i st an ce f ac t o r f o r fl ex u r e , 0 . 9
L R F D r es i st an ce f ac t o r f o r co m p r es s i o n , 0 .8 5
M ax i m u m co m p r es s iv e r e s i d u a l s t re s s , a s su m ed eq u a l t o 0 .3 t ry
for a l l cases
Th e m a t e r i a l y i e l d s t re s s , a s su m ed eq u a l t o 2 50 N/ m m 2 f o r a l l
cases
1 I N T R O D U C T I O N
Th e l i m i t - s t a t e s d es i g n o f b eam - co l u m n s i n b u i l d i n g f r am es h as b een a
su b j ec t o f r e sea r ch i n t e r e s t f o r m o r e t h an 2 0 y ea r s . A l m o s t a l l o f t h e
c u r r e n t d e s i g n m e t h o d s a r e b a s e d o n i n t e r a c t i o n e q u a t i o n s w h i c h ,t h r o u g h a co m b i n a t i o n o f an a l y ti ca l an d em p i r ica l m ean s , f it t h e u l t i m a t e
s t r en g t h o f an i n d i v i d u a l m em b er co n s i d e r i n g t h e e f f ec t s o f g eo m et r i c
i m p er f ec t i o n s an d r e s i d u a l s t r e s se s . B eam - co l u m n i n t e r ac t i o n eq u a t i o n s
can e s t i m a t e q u i t e accu r a t e l y t h e u l t i m a t e l o ad - ca r r y i n g cap ac i t y o f a
s i m p l y su p p o r t ed b eam - co l u m n wi t h eq u a l ex t e r n a l l o ad s ap p l ied a t b o t h
en d s . To g en e r a l i ze t h e eq u a t i o n s su ch t h a t t h ey m ay b e ap p l i ed f o r
m e m b e r s w i t h o t h e r l o a d i n g c a s e s a n d b o u n d a r y c o n d i t i o n s , a n d f o r
m em b er s i n g en e r a l f r am ewo r k s , ce r t a i n f ac t o r s t h a t ap p r o x i m a t e t h eac t u a l b eh av i o r o f t h ese m em b er s m u s t b e i n t r o d u ced . Th e e f f ec t i v e
l e n g t h is t h e k e y f a c t o r th a t h a s b e e n e m p l o y e d i n m a n y d e s ig n m e t h o d s t o
es t i m a t e t h e i n f l u en ce o f t h e o v e r a l l f r am ewo r k o n t h e s t r en g t h o f
c o m p o n e n t b e a m - c o l u m n m e m b e r s . D u e t o t h e a p p ro x i m a t e a n d e m p ir ic -
a l n a t u r e o f b eam - co l u m n i n t e r ac t i o n eq u a t i o n s , a n d s i n ce t h e i n t e r ac t i o n
b e t ween t h e m em b er s i n an ac t u a l f r am e a t t h e s t r en g t h l i m i t s t a t e i s
c o m p l e x , b e a m - c o l u m n e q u a t i o n s c a n n o t i n g e n e r a l p r o v id e a c c u r at e
p r ed i c t i o n s o f t h e m em b er f a i lu r e lo ad s i n an o v e r a l l s t r u c tu r a l sy s t em .T h i s p a p e r p r e s e n t s s e v e ra l in s ig h ts o n c u r r e n t N o r t h A m e r i c a n
m et h o d s an d t r en d s f o r b eam - co l u m n d es i g n i n s t ee l f r am ew o r k s . S ec t i o n
2 o f t h e p ap e r p r o v i d es an o v e r v i ew o f t h e d es i g n g u i d e l i n es an d
p r o c e d u r e s i n v o lv e d in th e d e v e l o p m e n t o f th e A m e r i c a n I n s t i tu t e o f S te e l
C o n s t r u c ti o n L o a d a n d R e s is ta n c e F a c t o r D e s ig n ( A I S C - L R F D ) i nt er a c-
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 4/40
272 J. Y. Richard Liew, D. W. White, W. F. Chen
t i on equa t ions . 1Th e s ign i f icance o f the e f fec tive leng th fac to r i n the L R F D
beam-co lumn in t e rac t ion equa t ions i s d i scussed in Sec t ion 3 . In th i s
se c ti o n , t h e a c c u r a cy o f t h e L R F D i n t e r a c ti o n e q u a t i o n s f o r c h e c k i n g t h e
s t reng th o f beam -co lum ns a s pa r t o f a s truc tu ra l sys t em i s exam ined us ing a
s imple s t ruc tu ra l subassembly .
Se v e r a l m e t h o d s f o r e s t im a t i n g c o l u m n e f fe c ti v e le n g t h s in u n b r a c e d
f rames a re p resen ted in Sec t ion 4 . Cha rac te r i s t i c r e su l t s o f t hese e f fec t ive
l eng th fac to r ca l cu la t ions a re show n fo r simple por t a l f ram es wi th uneq ua l
co lumn s t i f fnesses , fo r l eaned co lumn f rames wi th unequa l ax ia l l oads in
the co lumns , and fo r a gene ra l mul t i - s to ry f rame . The qua l i t i e s and
l i m i ta t io n s o f t h e d i f f e r e n t m e t h o d s a r e e x p l a i n e d u s i n g th e se e x a m p l e s .
T h e f i f t h s e c t i o n o f t h e p a p e r c o m p a r e s a n d c o n t r a s t s t h e c u r r e n t
r e c o m m e n d e d p r o c e d u r e s f o r b e a m - c o lu m n d e s ig n i n t h e A I S C - L R F D 1a n d C a n a d i a n S t a n d a r d s Sp e c if ic a ti o ns . 2 T h e f o r m e r r e q u i r e s t h e u se o f
the e f fec t ive l eng th concep t whereas the l a t t e r e l imina te s i t s use fo r
unbraced f raming sys t ems . A gene ra l t r end o f t hese spec i f i ca t ions i s
t o wa r d t h e u se o f d i r e c t s e c o n d - o r d e r e l a s t i c a n a l y s i s a s t h e m e t h o d o f
cho ice fo r ob ta in ing des ign fo rces . Bo th spec i f i ca t ions requ i re the
ca lcu la t ion o f second-o rde r e l a s ti c fo rces in f ram e m em bers . Th e s t ruc tu -
r a l m e m b e r s a r e t h e n d e s i g n e d b a se d o n u l t i m a t e s t r e n g t h i n t e r a c t i o n
e q u a t i o n s .f u n d a m e n t a l l y n o t c o m p a t i b le . O f c o u r se , t h e o n l y wa y o f p r o p o r t i o n i n g
b e a m - c o l u m n m e m b e r s i n o v e r a l l s t r u c t u r a l f r a m e wo r k s t h a t i s f u l l y
r a t i o n a l i s t h r o u g h t h e u se o f s e c o n d - o r d e r i n e la s t ic an a l y si s . H o w e v e r ,
s e c o n d - o r d e r i n e la s t ic a n a ly s i s m e t h o d s a r e o n l y b e g i n n i n g to b e c o m e
p r a c t ic a l f o r a c tu a l d e s i g n as a n a ly s i s m e t h o d s a r e i m p r o v e d a n d g e n e r a l
c o m p u t i n g p o w e r i s i n c r e ase d . T h e l a s t p a r t o f t h e p a p e r d is c u sse s p o s s i b le
m e t h o d s o f a c c u r a t e l y m o d e l i n g t h e i n e l a s t i c b e h a v i o r o f a s t r u c t u r a l
m e m b e r f o r t h e d e t e r m i n a t i o n o f o v e r a l l sy s t e m p e r f o r m a n c e . T h eprob lem s a ssoc ia t ed w i th the use o f e l a s ti c -pe r fec tly p l a s t ic ( i . e . , p l a s t i c
h inge ) a na lys i s i n gen e ra l f r ame d es ign a re addres sed , and poss ib l e
d i rec t ions fo r use o f ine l a s t i c ana lys i s a s a t oo l fo r m ore ra t iona l des ign o f
s t ee l beam-co lumns a re iden t i f i ed .
2 T H E A I S C - L R F D B E A M - C O L U M N I N T E R A C T I O N
E Q U A T I O N S
Fo r t h e d e s i g n o f st e e l b e a m - c o l u m n s , t h e A I S C - L R FD sp e c if ic a ti o n 1
p r o v i d e s t h e f o l lo wi n g in t e r a c t i o n e q u a t i o n s :
Pu 8 ( Mux MuY ) = 1 " 0 for Pu >-0"2 (1)~bc----P-ff+ ~bb Mnx ~- ¢ b M .y ~b¢- - - ~
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 5/40
Beam--column design in steel rameworks 273
Pu t M__________~_~ Muy = 1.0 for Pu < 0.2 (2)2 5 c P n ¢t~bMnx ¢~bbMny ~c p n
w h e r e P u is h e r e q u i r e d a x i a l t r e n g th ; ~ is h e n o m i n a l ax i a l o m p r e s s i v e
s t r e ng t h ; M ~ , a n d M u y a r e t h e r e q u i r e d f l e x u r a l s t r e n g t h w i t h i n t h e
u n b r a c e d l e n g t h o f t h e m e m b e r ; M . x a n d M n y a r e t h e n o m i n a l f l e x u r a l
s t r en g t h s; a n d ~'c a n d ~ a r e t h e r e s i st a n c e f a c t o r s f o r c o m p r e s s i o n a n d
f l e x u r e .
T h e L R F D s pe ci fi ca ti on u g g e s t s t h e f o l l o w i n g p r o c e d u r e t o e s t i m a t e
t h e s e c o n d - o r d e r el as ti c o m e n t M u i n l i eu f a d i r e c t e c o n d - o r d e r e la s ti c
ana lys i s :
Mu = B1Mnt + B2Mlt (3)
In th i s equa t ion , M~t and M~t a re the m axim um f i rs t -o rde r el a s ti c m om ent s
i n t h e m e m b e r b a se d o n ' n o t r a n s l a t i o n ' a n d ' l a te r a l t r a n s l a t io n ' a n a l y se s
of the f rame re spec t ive ly . B1 and B2 a re moment ampl i f i ca t ion fac to r s
w h i c h a c c o u n t f o r P - 8 a n d P - A e ff ec ts .
2 . 1 D e v e l o p m e n t o f t h e L R F D i n te r a c ti o n e q u a t i o n s - - g r o u n d r u le s
I n t h e d e v e l o p m e n t o f t h e L R F D i n t e r a c t i o n e q u a t i o n s , t h e f o l l o w i n g
g u i d e l i n e s w e r e e s t a b li sh e d : 3
( 1) T h e e q u a t i o n s sh o u l d b e a p p l i ca b l e t o a w i d e r a n g e o f p r o b l e m s
su c h a s s tr o n g - a n d we a k - a x i s b e n d i n g , swa y a n d n o n - swa y f ra m e s ,
l a t e r a ll y l o a d e d c o l u m n s , i m p e r f e c t c o l u m n s w i t h v a r i o u s c o l u m n
s l e n d e r n e s s r a t io s a n d d e g r e e s o f e n d r e s t r a in t , a n d l e a n e d c o l u m n
sy s t e m s . T h e y sh o u l d a c c o u n t f o r i n e l a s t i c b e h a v i o r a n d s e c o n d -
orde r e f fec t s .
( 2) T h e e q u a t i o n s sh o u l d c l e a r l y d i s ti n g u i sh b e t w e e n t h e l o a d e f f e c tsand the re s i s t ances so tha t seco nd-o rde r e l a s ti c ana lys i s can be eas i ly
a c c o m m o d a t e d .
( 3 ) T h e e q u a t i o n s sh o u l d b e b a se d o n t h e l o a d e f f e c t s o b t a i n e d f r o m
secon d-orde r e las tic ana lysis s ince , a t the pr esen t t ime, secon d-order
ine la s t ic ana lys i s i s no t r ead i ly access ib l e fo r des ign o f fi ce use .
( 4) T h e e q u a t io n s s h o u l d n o t be m o r e t h a n 5 % u n c o n s e r v a ti v e w h e n
c o m p a r e d t o s e c o n d - o r d e r p l a st ic - z o n e so l u ti o n s .
( 5 ) T h e e q u a t i o n s sh o u l d n o t n e e d t o c o n s i d e r s t r e n g t h a n d s t a b i l i t y
sep a ra t e ly , s ince in gen e ra l , a l l co lum ns o f f in it e l eng th fa il by som e
c o m b i n a t i o n o f i n e l a s ti c b e n d i n g a n d s t a b i li t y e f fe c ts .
( 6 ) T h e s a m e u l t i m a t e s t r e n g t h sh o u l d b e p r e d i c t e d f o r s i m i l a r m e m -
b e r s , su c h a s t h e o n e s sh o w n i n F ig . 1 . T h e b e h a v i o r i n e a c h o f t h e se
prob lem s i s phys ica l ly iden t i ca l in bo th the e l a s ti c an d ine l a s ti c
r a n g e s .
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 6/40
2 7 4 J. Y. Richard Liew, D. W. White, W. F. Chen
"V
2L
_1_
~P I-t
H
l P
~ P H P ~ H
L
g.,~_H.H
t o
H ~ P
t p "
F i g . 1 . B e a m - c o l u m n p r o b l e m s w h i c h h a v e id e n t i c a l s o l u ti o n s .
( 7) A d j u s t m e n t o f e f f e c ti v e l e n g t h b a s e d o n c o l u m n in e l a st ic i ty s h o u l d
b e a l l o w e d .
2.2 Development of the LRFD interaction eq u at io~ procedure
A n u m b e r o f planar s e c o n d - o r d e r p l a s t i c - z o n e s o l u t i o n s h a v e b e e n
g e n e r a t e d a n d r e p o r t e d b y K a n c h a n a la i . 4 T h e L R F D i n te r a c t io n e q u a -
t i o n s w e r e d e t e r m i n e d i n p a r t b y c u r v e f i t t i n g t o t h e s t r e n g t h c u r v e s
o b t a i n e d f r o m t h e s e i n el a st ic a n al y se s . T h e p r o c e d u r e u s e d i n d e v e l o p i n g
t h e L R F D i n t e r a c t i o n e q u a t i o n s is o u t l i n e d b e l o w : 3'5
( 1) U l t i m a t e s t r e n g t h c u rv e s d e t e r m i n e d i n K a n c h a n a l a i ' s w o r k w e r e
p r e s e n t e d i n a n o n d i m e n s i o n a l i z e d f o rm . T h e n o r m a l i z e d a xia l l o a dP/Py w a s p l o t t e d a g a i n st t h e n o r m a l i z e d f i rs t - o rd e r m o m e n t M1/Mp.T y p i c a l r e s u l t s f o r a b e a m - c o l u m n b e n t a b o u t t h e w e a k a x i s a n d
h a v i n g L/r = 1 00 a r e s h o w n i n F i g . 2 . A l l t h e m e m b e r s w e r e
a s s u m e d t o b e p e r f e c t l y s t r a i g h t w i t h a m a x i m u m c o m p r e s s i v e
r e s i d u a l s t r e s s o f tr ~ = 0 .3 0 ry a n d a y i e l d s t r e s s o f O-y = 2 5 0 N / m m 2 .
I t s h o u l d b e n o t e d t h a t t h e b e h a v i o r o f t h e t w o m e m b e r s s h o w n i n
t h e f i g u r e is i d e n t i c a l i n b o t h t h e e l a s ti c a n d i n e l a s ti c r a n g e s .
( 2 ) T h e n o r m a l i z e d first-order m o m e n t M1/Mp, o b t a i n e d f r o m t h ep l a s t i c - z o n e a n a l y s i s , w a s c o n v e r t e d t o a second-order elasticm o m e n t M2/Mp u s in g t h e s e c o n d - o r d e r e la s ti c m o m e n t a m p lif ic a -
t i o n f a c t o r . F o r t h e b e a m - c o l u m n s s h o w n i n t h e f i g u r e , t h e
s e c o n d - o r d e r e l a s ti c m o m e n t a m p l if ic a t io n f a c t o r is t a n a/a, w h e r e
a = 0-5 ~" V'ffTP~.
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 7/40
Beam -column design in steel ram eworks 275
P
0.8
0,7
0 .6
0 .5
0.4
0 .3
0 .2
0.1
- t P t p
~ ~ Kanch ana la i , 1977 - ~ ~ ~ ~
- x \1 I I •
0.25 0.5 0.75 1.0
M 1 IMp o r M 2 IMp
Fig. 2. Procedure for obtaining the ne t MI/M p and M2[Mp cu rv e s .
( 3) T h e c o l u m n s t r e n g t h o f a n a x ia l ly l o a d e d m e m b e r w i t h L / r = 100 is
g i v e n b y t h e L R F D c o l u m n - s t r e n g t h e q u a t i o n a s 0 -5 91 Py . Ho w e v -
e r , t h e c o l u m n s t r e n g t h ( f o r z e r o b e n d i n g m o m e n t ) c o m p u t e d b y
K a n c h a n a l a i ' s p l a s t ic - z o n e a n a l y s i s is a p p r o x i m a t e l y e q u a l t o0 .7 1 Py. T h i s d is c r e p a n c y is d u e t o t h e f a c t t h a t t h e L R F D c o l u m n
e q u a t i o n s w e r e d e r i v e d b a se d o n t h e a s su m p t i o n t h a t t h e c o l u m n i s
i n i ti a l ly c r o o k e d , h a v i n g a m a x i m u m m i d - l e n g t h d e f le c t io n o f
a p p r o x i m a t e l y L / 1 5 0 0 . However , t he ine l a s t i c ana lys i s i s fo r a
p e r f e c t ly s tr a i g h t m e m b e r . T o i n c lu d e t h e ' i m p e r f e c t i o n e f f e ct ' in
t h e b e a m - c o l u m n i n t e r a c t i o n e q u a t i o n s , t h e ' u se d - u p ' f i r s t - o r d e r
m o m e n t c a p a c i ty d u e t o c o l u m n i n i ti a l i m p e r f e c t io n s wa s a s su m e d
t o v a r y l i n e a r l y w i t h t h e a x i al lo a d , a s sh o wn i n F i g . 2 . T h e n e t u se f u lf i r s t - o r d e r m o m e n t c a p a c i t y wa s t h e n o b t a i n e d b y su b t r a c t i n g t h e
' u se d - u p ' m o m e n t f r o m t h e f i r s t - o r d e r m o m e n t M1 . T h i s v a l u e ,
w h e n m u l t ip l i e d b y t h e e l a s ti c m o m e n t a m p l i f ic a t io n f a c t o r y i e ld s
t h e n e t u se f u l s e c o n d - o r d e r m o m e n t c a p a c i t y ( sh o wn a s t h e n e t
ME/M p in Fig . 2) .
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 8/40
276 J . Y . Richa rd L iew , D . W . W h i t e , W . F . Chen
0 .8
P
Py
0.7
0 .6
0 .5
0 .4
0 .3
0 .2
0.1
{ P ~ P
4 - - H
N et M 2 = N e t M I x tan..__..~ 2 O R
Q
Pn 0 .5 9 1 o t = ~ - ~ . ~ H H
t p tP y
" ~ M p ~ L R F D ( E q n s 1.2)
" M r, ~ ' - ~ . . . ~ ~ M 2
L R F D M.I ~ " - ~ -" ~ " ~
• . / " - . ' ~ . - ~ ' ~
N e t @ C u r v e ~" - .~ . ~ * .~a p " ; " ~ ll~ t, ~ ' ~ "
0 .25 0 .5 0 .75 1 .0M
M p
Fig. 3 . C u r v e - fi tt in g o f t h e A I S C -L R a R D b e a m - c o l u m n e q u a t i o n s .
( 4 ) T h e n e t r e su l ts ar e p l o t t e d i n F i g . 3. T h e L R F D e q u a t i o n s a r e
o b t a i n e d b y c u r v e fi tt in g t o th i s n e t s e c o n d - o r d e r m o m e n t . S i m i la r
c u r v e s h a v e b e e n g e n e r a t e d f o r a w i d e v a r ie t y o f c a s e s in c l u d i n gs tr o n g - a n d w e a k - a x i s b e n d i n g , s w a y a n d n o n - s w a y , a n d l e a n e d
c o l u m n s ys te m s . T h e L R F D i n te r a c ti o n e q u a t i o n s ar e n o m o r e t h a n
5 % u n c o n s e r v a ti v e w h e n c o m p a r e d t o a ll o f th e c o m p u t e d r e su lt s
f o r in - p l a n e s t r o n g -a x i s a n d w e a k - a x i s b e n d i n g .
T h e w e a k a x i s L /r = 1 0 0 c a s e w a s t h e m o s t c r i t i c a l o f a l l t h e
c o m p u t e d r e su lt s s f o r th e b e a m - c o l u m n s s h o w n i n F i gs 2 a n d 3 . T h e
L R F D e q u a t i o n s s h o w a n e x c e l l e n t f it t o t h is c u r v e . I n g e n e r a l , t h e
e q u a t i o n s a l s o g i v e a s u p e r b f i t f o r a ll s t r o n g - a x i s c a s e s o f t h e t y p es h o w n i n F i g . 3 fo r L /r r o m 0 t o 1 0 0 , b u t t h e y a r e v e r y c o n s e r v a t i v e
f o r t h e w e a k - a x i s c a s e w h e n L /r r a n g e s fr o m 0 t o 4 0. T h e y a r e
m o d e r a t e l y c o n s e r v a t i v e f o r b o t h a x e s w h e n L /r s g r e a t e r t h a n 1 2 0 .
( 5 ) T h e f i n al L R F D e x p r e s s i o n s a r e o b t a i n e d b y i n c o r p o r a t i n g t h e
r e s i s t a n c e f a c t o r s , (/)b a n d d )c .
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 9/40
B eam-colu mn design n teel ram ewor ks 277
3 S I G N I F I C A N C E O F T H E E F F E C T I V E L E N G T H F A C T O R I N
T H E L R F D B E A M - C O L U M N E Q U A T I O N S
M a n y f o r m s o f b e a m - c o l u m n i n t er a c ti o n e q u a t i o n s h a v e b e e n p r o p o s e d i np r e v i o u s w o r k b a s e d o n t h e u s e o f a n e f f e c t iv e l e n g t h f a c to r o f 1 . 0. F i g u r e 4
c o m p a r e s t h e r e su lt s o b t a i n e d u s in g t h e S S R C P - A m e t h o d 6 w i t h th e
p l a s t ic - z o n e s o l u t i o n 4 f o r a s i m p l e p o r ta l f r a m e . T h e e x a m p l e f r a m e h a s a
r i g id g i r d e r a n d a p i n n e d b a s e . T h e t w o i n t e r a c t i o n e q u a t i o n s o f t h e P - A
m e t h o d , s h o w n i n t h e f i g u r e , a r e e x p r e s s e d i n a s t r e n g t h f o r m a t f o r t h i s
e x a m p l e . F o r p u r p o s e s o f c o n s i s te n c y w i t h t h e o th e r p r o c e d u r e s d i s c u s se d
in th e p a p e r , t h e L R F D c o l u m n s tr e n g th f o r m u l a s ar e u s e d h e r e t o
c o m p u t e Pn - I n t h e P - A a p p r o a c h , t h e c o u p l e d m e m b e r a n d s y s t e m
s ta b il it y e f fe c t s o n b e a m - c o l u m n s tr e n g t h a re c o n s i d e r e d o n l y i n t h e
P
Py
1 . 0 !
~ P 0.6M*' - - + 1.0
0 .8 P nK ~ O 1 1 - ~ - ) M p~ , g - l o
P M " H Lc- - + = 1 .0 , M*
0.6 ~, Py Mp 1- PL2c / 13E [ c )
Unco nservat i~ % ax is }e'~ j StrongW eak a x i s ~ r~ an ~.an aD a, 1977)
0 ,4 ~ G 0
H lb GB = ooA
0 .0 0.2 0.4 0.6 0.8 1.0
H Lc / 2Mp
Fig. 4. Com parison of the SSR C P - A equations6 with ultima te strength curves based oninitially perfect ge om etry.L
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 10/40
278 J. Y. Richard Liew, D. W. White, W. F. Chen
e q u a t i o n w h i c h c o n t a i n s P n a n d P e ( t h e o t h e r e q u a t i o n o n l y c o n t a in s
c r o s s - se c t io n s t r e n g t h te r m s ) . T h e P - A m e t h o d 6 s u g g e s t s t h a t K = 1 .0
m a y b e u s ed to e v a lu a t e P n w h e n M * is b a s e d o n a P - A t y p e o f
s e c o n d - o r d e r e l a st ic a n a ly s is . T h i s is a n a t t e m p t t o s e p a r a t e m e m b e r
s ta b i li ty f r o m f r a m e s t a b i li ty b y c o n s i d e r i n g f r a m e s ta b i li ty o n l y t h r o u g h
t h e c a l c u la t io n o f M * . H o w e v e r , th i s a p p r o a c h d o e s n o t c o r r e la t e w e l l w i t h
' e x a c t ' i n e l a s ti c s t r e n g t h c u r v e s s u c h a s K a n c h a n a l a i ' s . I n a c t u a l it y , t h e r e is
m o r e c o u p l i n g b e t w e e n s y s te m a n d m e m b e r s ta b il it y e f fe c ts t h a n t h e P - A
i n t e ra c t i o n e q u a t i o n s im p l y . F i g u re 4 s h o w s th a t t h e P - A m e t h o d i s i n
g e n e r a l u n c o n s e r v a t i v e c o m p a r e d t o t h e ' ex a c t ' i n e la s ti c s t re n g t h . F u r t h -
e r m o r e , t h e m e t h o d p r o d u c e s d i f f e r e n t r e su l ts f o r t h e d i f f e re n t p r o b l e m s
s h o w n in F ig . 1 .
I f K i s t a k e n a s u n i t y , t h e e r r o r i n u s i n g t h e p r e s e n t A I S C - L R F Di n t e r a c t i o n e q u a t i o n s is a ls o u n a c c e p t a b l y l a r g e ( s e e F ig s 5 a n d 6 ). F i g u r e 5
is a c o m p a r i s o n o f th e s t r e n g t h c u r v e s d e t e r m i n e d b y K a n c h a n a l a i ( w h i c h
a r e b a s e d o n a f r a m e w i t h n o i n it ia l o u t - o f - p lu m b n e s s o r c o l u m n s w i th n o
i ni ti al o u t - o f- s tr a ig h t n e s s) v e rs u s th e A I S C - L R F D b e a m - c o l u m n s tr e n g t h
c u r v e s . F i g u r e 6 c o m p a r e s t h e c u r v e s a f t e r K a n c h a n a l a i ' s d a t a i s a d j u s t e d
b y t h e p r o c e d u r e s d i s c u s s e d i n S e c t i o n 2 . 2 t o a c c o u n t f o r i m p e r f e c t i o n s .
T h e e r r o r s a s s o c i a t e d w i th u s in g K = 1 a r e p a r ti c u l a rl y l a r g e f o r m e m b e r s
o f i n t e r m e d i a t e t o l o n g l e n g t h s s u b j e c t e d t o r e l a ti v e l y h i g h a x ia l l o a d s . O nt h e o t h e r h a n d , f o r t h e f r a m e s u b a s s e m b l a g e c o n s i d e r e d h e r e , t h e
e q u a t i o n s g i v e a g o o d f it t o t h e m o r e e x a c t s o l u ti o n w h e n a K o f 2 . 0 is u s e d .
A l t h o u g h a c u r r e n t t r e n d i s t o a v o i d th e u s e o f e f f e c ti v e l e n g t h f a c to r s i n
t h e d e s i g n o f s t e e l f r a m e s , i t a p p e a r s t h a t i t i s a l m o s t i m p o s s i b l e t o
f o r m u l a t e a n i n t e r a c t i o n e q u a t i o n t h a t i s a c c u r a t e f o r a l l r a n g e s o f a x i a l
l o a d a n d m o m e n t w i t h o u t c o n s i d e r i n g t h e e f f e c ti v e l e n g t h d ir e c tl y . T h i s
a s p e c t i s d i s c u s s e d in m o r e d e t a i l in S e c t i o n 6 .
H o w e v e r , i t s h o u l d b e n o t e d t h a t t h e u s e o f K = 1 .0 is o n l y sl ig h t lyu n c o n s e r v a t i v e a s l o n g a s t h e a x i a l l o a d i n t h e b e a m - c o l u m n i s n o t
e x c e ss iv e . T h e C a n a d i a n S t a n d a r d 2 p r o p o s e s a b e a m - c o l u m n e q u a t i o n
w h i c h u s e s K = 1 . 0 , b u t it i n d i r e c t l y l i m i t s t h e a x i a l c a p a c i t y b y i m p o s i n g a
l i m i t o n t h e s e c o n d - o r d e r e l a s t i c m o m e n t a m p l i f i e r a n d r e q u i r i n g t h a t
g r a v it y lo a d e d f r a m e s b e s u b j e c t e d t o a m i n i m u m l a t er a l lo a d a s s o c ia t e d
w i t h s t o r y o u t - o f - p l u m b n e s s . T h e b a s i c c o n c e p t s a s s o c i a t e d w i t h t h e
C a n a d i a n S t a n d a r d i n t e r a c ti o n e q u a t i o n s f o r b e a m - c o l u m n d e s i g n a r e
d i s c u s s e d in S e c t i o n 6 .
F o r u n b r a c e d f r a m e s , t h e L R F D s p e ci fi ca ti o n r e q u i r e s th a t P n b e
c a l c u l a t e d b a s e d o n K - > 1 . I f a f ir s t - o r d e r e l a s ti c a n a l y s is is e m p l o y e d , B 1
s h o u l d b e d e t e r m i n e d b a s e d o n t h e e la s t ic b u c k li n g l o a d o f t h e m e m b e r ,
P e , w i t h K - 1 ( i . e ., th e c o l u m n is a s s u m e d t o b e p r e v e n t e d f r o m
s i d e - sw a y ) . F o r b r a c e d f r a m e s , i t is a d v i s a b l e t o u se K = I f o r e v a l u a t i o n
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 11/40
B eam-co l u m n desi gn n st eel r am ewo r ks 2 7 9
1 .0
0 .8
P
P y
0 .6
0 .4
0 .2
0 .00 .0
Strong a x i s.../ i ; : _ / W e a k a x 's } ( Ka n ch a na la i' 1 9 77 )
~:~F... / G A - 0~,. Ga-¢°"..~,a(X."-, L/r - 40
" . . " ,. LRF D (K = 1 .0)
L c I e
0 . 2 0 . 4 0 . 6 0 . 8 1 . 0
H L c / 2 M p
F i g. $ . C o m p a r i s o n o f t h e A I S C - L R F D b e a m - c o l u m n e q u a ti o n s w i t h e x a c t u l ti m a t e
s t r e n g t h c u r v e s f o r i n i t ia l l y p e r f e c t g e o m e t r y . 4
1 .0
0 .8
P
0 .6
0 .4
0 .2
0 .00 .0
• .. GA " 0GB - ,aD
LR FD (K = 1 . 0 ) L / r = 40
• . . . . . ' " . . . . . . t ,~ °a~gaxa~;s Ka nch an ala,ad j us t ed ,
0 . 2 0 . 4 0 . 6 0 . 8 1 . 0
HL~/2M p
F i g. 6 . C o m p a r i s o n o f t h e A I S C - L R F D b e a m - c o l u m n e q u a t io n s w i th t h e u l t im a t e s tr e n g th
c u r v e s4 a d j u s t ed t o a c c o u n t f o r f r a m e i m p e r f e c t io n s .
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 12/40
280 j. Y. Richard Liew, D. W. White, W. F. Chen
of P,. If the designer relies on the beams to restrain the columns (i.e., if
K-< 1 is used in the determination of P.) the beams should be designed to
carry the second-order moments induced by the columns.7
For an unbraced frame, the calculation of B2 by LRFD equation H1-6
involves the calculation of Pek for all the columns in a story which offer
restraint to side-sway buckling. K is generally assumed to be greater than
one for these cases--al though for some of the procedures discussed in the
next section, the computed K factor may be less than one. As an
alternative to the use of the B1 and B2 factors, the second-order elastic
moments may be obtained directly from a second-order elastic analysis.
However, an accurate calculation of member P - 8 moments is generally
not provided by most second-order analysis programs. 8
The P. term in the LRFD interaction equations is governed by the
maximum column slenderness ratio KL/r for strong- or weak-axis
bending. The term Pek, used in the calculation of the B1 and B2 factors, is
always governed by the slenderness ratio in the plane of bending. In
general, the design thus involves the calculation of the effective length for
both axes of bending. Therefore, a correct interpretation of K factors in
the various terms of the interaction equation is essential.
In the following sections, various methods of computing the K factors in
unbraced frames are examined. Their use with the LRFD equations forchecking beam-column strength is discussed using several simple structu-
ral subassemblies.
4 COMPUTATION OF THE EFFECTIVE LENGTH FACTOR
A variety of methods have been suggested for calculation of K factors.
These methods may be grouped according to those associated with: (1) thebuckling of an idealized subassemblage, (2) the buckling of a story, and (3)
the buckling of the overall structural system. Some of the methods are
suitable for hand calculations. Others are obtained typically from com-
puter solutions. All of the methods involve certain assumptions and
simplifications. Some of the most popular methods are briefly reviewed in
the following sections.
4 . 1 A l i g n m e n t c h a r t m e t h o d (b a s e d o n t h e bucklingo f a n i d e a li z e d
s u b a s s e m b l a g e )
The most widely used method for calculating K factors in rectangular
building frameworks is the alignment chart method.9 For an unbraced
frame, this method is based on the buckling of the subassemblage shown in
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 13/40
Beam --column design in steel~rameworks 281
( a )
J l3 /
GA K
oo ' 20.0
100.0 10.050.030.0 5.0
20.0 4.0
10.09 . 0 -
8 . 0 -7 .0 -
6.0
5 . 0 -
4 .0
3 .0
2 .0 -
1.0.
3.0
2.0
1.5
1.0
GB
~oo
-100.0
50.0
30.0
20.0
10.09.0
8 .07.0
6.0
5.0
4.0
3.0
2.0
1.0
( b )
F i g . 7 . ( a ) Subassemblagem o d e l o f a n u n b r a c e d f r a m e ; ( b ) a l ig n m e n t c h a r t K f a c t o r f o r
u n b r a c e d f r a m e s .
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 14/40
282 J. Y. Richard Liew, D . W . W hite , W . F. Chen
F ig . 7 a. T h e b a s ic m e t h o d i n v o l v e s t h e f o l l o w i n g m a i n a s s u m p t i o n s : ( 1 ) A l l
m e m b e r s a r e p r i s m a t i c a n d a ll j o i n t s a r e r ig i d . ( 2 ) T h e c o l u m n s ti ff n e ss
p a ra m e te r L ~ ] s i d en ti c al f o r a l l c o lu m n s . T h a t is , a t i n c ip ie n t
b u c k l in g , n o n e o f t h e o t h e r p o r t i o n s o f t h e f r a m e c o n t r i b u t e s a n y l at e ra l
r e s tr a in t a t t h e b o u n d a r i e s o f t h e s u b a s s e m b l a g e , a n d a ll m e m b e r s a r e b e n t
i n d o u b l e c u r v a t u r e w i t h a p o i n t o f i n f l e c t i o n a t t h e m i d s p a n o f e a c h
m e m b e r . ( 3 ) A x i a l f o r c e s i n t h e g i r d e r s a r e n e g l i g i b l e . ( 4 ) T h e r a t i o
b e t w e e n t h e b e a m a n d c o l u m n b e n d i n g s ti ff ne ss is u n a f f e c te d b y d i s tr i-
b u t e d y i e l d i n g i n t h e c o l u m n s o r p o s s i b l e p l a st ic h i n g e f o r m a t i o n i n t h e
b e a m s ( i . e . t h e m e m b e r s a r e a s s u m e d e l a s t i c f o r c a l c u l a t i o n o f r e l a t i v e
m e m b e r st if fn e s se s ). ( 5) T h e r o t a ti o n s a t o p p o s i te e n d s o f th e b e a m s a r e
e q u a l in m a g n i t u d e , p r o d u c i n g r e v e r s e c u r v a t u r e b e n d i n g .
A s a r e s u l t o f t h e s e a s s u m p t io n s , t h e b u c k l i n g s o lu t i o n fo r t h e u n b r a c e ds u b a s s e m b l a g e s h o w n in F ig . 7 c a n b e o b t a i n e d f r o m t h e t r a n s c e n d e n t a l
e q u a t i o n ,
GA GB (~/K ) 2 - 36 (1r/K) - 0 (4)
6 ( G A + G s ) t an (Tr/K)
w h e r e G A a n d G s a r e t h e c o l u m n to b e a m s ti ff n es s r a ti o s a t th e t w o
c o l u m n e n d s . T h e s e t e rm s c a n b e w r i tt e n a s
Z ( E l c
G A =
GB ~ °' °E / ( 6 )
T h e s o l u t io n o f e q n ( 4) c a n b e e x p r e s s e d i n t h e c o n v e n i e n t f o r m o f t h e
a l i g n m e n t c h a r t s h o w n i n F ig . 7 b. S i n c e th e a b o v e e q u a t i o n s a s s u m e t h a t
a l l j o i n t s a r e r i g i d , t h e g i r d e r s t i f f n e s s ( I / L ) b n e e d s t o b e m o d i f i e d a s
f o l lo w s i f t h e g i r d e r s h a v e d i f f e r e n t b o u n d a r y c o n d i t i o n s a t t h e i r f a r e n d s .6
F o r u n b r a c e d f r a m e s ,
( i) i f t h e f a r e n d o f t h e g i r d e r is fi x ed , d i v i d e ( I / L ) b by 1 .5 ,( ii ) i f t h e f a r e n d o f t h e g i r d e r is h i n g e d , d i v i d e ( l / L ) b b y 2 . 0 .
I f a c o l u m n i s l o a d e d i n t h e i n e la s ti c r a n g e w h i le t h e a d j a c e n t b e a m s
r e m a i n e l as t i c , th e b e a m s b e c o m e m o r e e f f e c ti v e i n r e s tr a i n in g t h e c o l u m n
a g a in s t b u c k l i n g ; t h e r e f o r e , t h e e f fe c ti v e l e n g t h o f t h e c o l u m n i s r e d u c e d .
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 15/40
Beam-columndesign n steel ram eworks 283
A s a re s u l t , t h e b u c k l i n g l o a d o f t h e c o l u m n i s h i g h e r t h a n t h a t c a l c u l a t e d
b a s e d o n a n e l a s t i c K - f a c t o r . T h e A I S C - L R F D M a n u a l 1 s u g g e s t s th a t i n
d e t e r m i n i n g t h e e f fe c t i v e l e n g th f o r th e P n t e rm i n t h e b e a m - c o l u m n
i n t e r a c t i o n e q u a t i o n s , t h e c o l u m n t o b e a m s t if f n es s r a t io s i n e q n s ( 5 ) a n d( 6 ) m a y b e c a l c u l a t e d a s
G i n e l a s t i c =
E ( EtE E IcL c
/(7 )
t o a c c o u n t f o r th e i n e l a s t i c it y i n t h e c o l u m n s . T h e t e r m E t / E i n th i s
e q u a t i o n i s r e f e r r e d t o a s t h e i n e l a s t i c s ti f fn e s s r e d u c t i o n f a c t o r , a n d i t i s i n
g e n e r a l d i f f e r e n t f o r e a c h c o l u m n e n t e r i n g t h e j o i n t . T h i s f a c t o r is d e f i n e d
in t h e L R F D m a n u a l a s
Et Pn inelast ic 0" 65 8A- - ~ - = < 1 - 0 ( 8 )
E P n e l a st ic 0 " 8 7 7 /A -
w h e r e A i s d e f i n e d i n t e r m s o f P/Py a s
~ l n (eu/Py)A = In 0.658 (9)
T h i s e q u a t i o n is o b t a i n e d b y s o lv i n g t h e L R F D i n e l a s t ic c o l u m n s t re n g t h
e x p r e s s i o n f o r t h e s le n d e r n e s s p a r a m e t e r it c o r r e s p o n d i n g t o P n = P u. T h e
v a l u e o f i t i s l e s s t h a n 1 . 5 f o r c o l u m n s w h i c h f a i l i n t h e i n e l a s t i c r a n g e .
U s i n g e q n ( 9 ), a c o r r e s p o n d i n g it c a n b e o b t a i n e d f o r a g i v e n P J P y . T h ei n e l a s ti c s ti ff n e s s r e d u c t i o n f a c t o r c a n t h e n b e c a l c u l a t e d b y s u b s t i t u t i n g
e q n ( 9 ) i n t o e q n ( 8 ) . T h e r e s u l t i n g v a l u e s o f E t / E a r e s h o w n i n F i g . 8 . I ts h o u l d b e n o t e d f r o m F i g . 8 t h a t t h e i n e l a s t ic st if f n es s r e d u c t i o n f a c t o r i s
l es s t h a n o n e o n l y w h e n Pu/Py >-0 . 3 9 , a n d i t s u s e i s l i m i t e d o n l y t o t h e a x i a l
r e s i s t a n c e t e r m i n t h e b e a m - c o l u m n i n t e r a c t i o n e q u a t i o n . E l a s t i c e f f e c ti v e
l e n g t h s m u s t b e u s e d w i t h t h e B 1 a n d B 2 t e r m s s i n c e s e c o n d - o r d e r elasticm o m e n t s a r e t o b e c o m p u t e d u s i n g t h e s e te r m s .
4 . 2 L e M e s s u r i e r ' s m e t h o d ( b a s e d o n t h e b u c k l i n g o f a s t o r y )
T h e a l i g n m e n t c h a r t m e t h o d is b a s e d o n t h e a s s u m p t i o n t h a t a ll c o l u m n s i n
a s to r y b u c k l e s i m u l t a n e o u s l y , w i t h o u t a n y p a r t ic u l a r c o l u m n s p r o v i d i n g
l a te r a l r e s t ra i n t t o o t h e r c o l u m n s . L e M e s s u r i e r p r o p o s e d a m e t h o d f o r
u n b r a c e d f r a m e s i n w h i c h t h e l a te r a l r e s tr a i n i n g e ff e c t s p r o v i d e d b y t h e
c o l u m n s i n a s t o r y h a v i n g s m a l l e r st if f n es s p a r a m e t e r s ( L ~ / P u / E I ) c a n b e
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 16/40
2 8 4
1.0
0 .9
0 . 8 i
0 .7
0 .6
Et 0.5E
0 ,4
0 ,3
0 .2
0.1
J . Y . R ichard L iew , D . W . White, W. F . Chen
, ,
il j 0 . 3 9 | a i ~ I , ~,0 .1 0 .2 0 .3 0 .4 0 ,5 0 .6 0 .7 0 .8 0 .9 1 .0
P / P y
F i g . 8 . C o l u m n i n e l a s t i c s t i f f n e ss r e d u c t i o n f a c t o r .
a c c o u n t e d f o r . 10 A m o d i f i e d f o r m o f h is f o r m u l a f o r t h e e f f e c t i v e l e n g t h
f a c t o r c a n b e w r i t t e n a s
~ e t , [ ~ eu + yC , eu ]K i 2 = P u i L i 2 L X P L
( 1 0 )
w h e r e t h e s u b s c r i p t i r e f e r s t o t h e i t h c o l u m n i n t h e s t o r y , a n d t h e
c o r r e s p o n d i n g e l a s t i c s e c o n d - o r d e r m o m e n t a m p l i f i c a t i o n f a c t o r i s
A F =E P u ) ( 1 1 )
1 - y pL _ Y~ ( CL P u)
w h e r e
e u i
] i
L iPL
= s u m o f a ll v e r t ic a l fo r c e s a c ti n g o n t h e s t o r y a t t h e f a c t o r e d l o a d l e v e l
= a x i al f o r c e o n c o l u m n i
= m o m e n t o f i n e r t i a o f c o l u m n i
= h e i g h t o f c o l u m n i= t h e f o r c e th a t p r o d u c e s a u n i t r o t a t i o n a l d i s p l a c e m e n t A / L o f t h e
m e m b e r . P L m a y b e w r i t te n a s
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 17/40
Beam --column design in steel ram ewo rks 285
CL = stiffness correction factor for a column, w hich accounts for P -effects and can be w ritten as
K2
= column e nd re strain t coefficient defined as
6 (GA + GB) + 36
2(GA + G B ) + G A G B + 3
N o t e t h a t t h e m e m b e r K f a c t o r in th e e x p r e s s i o n f o r t h e C I. t e r m i s
o b t a i n e d f r o m t h e a l i g n m e n t c h a r t p r o c e d u r e . Fo r a g e n e r a l c a se , t h e
p a r a m e t e r s PL a n d C L m a y b e o b t a i n e d a l so b y d i re c t a n a ly s i s.
I f t h e L R FD B 2 f a c t o r ( e q n H1 - 6 o f t h e L R FD sp e c i f i c a t i o n ) i s u se d
i n s t e a d o f e q n ( 1 1 ), t h e n t h e a m p l if ic a t io n f a c t o r m a y b e w r i tt e n a s
A F = B 2 =
Y-Pu ) (12)1 - E Pei
w here E Pet i s t he su m of the e l a s t i c buc k l ing loads o f a ll t he co lum ns in thes t o ry . U s i n g L e M e ssu r i e r ' s a p p r o a c h , t h e l o a d i n a n y i n d iv i d u a l c o l u m n a t
t h e e l as t ic b u c k l i n g o f th e s t o r y m a y b e w r i tt e n a g
E/iP e i = ~ ( I 3 )
Sub s t i tu t ing Ki f rom eqn (10) in to eqn (13) a nd su bs t i t u t ing the re su l t so
o b t a i n e d i n t o e q n ( 1 2 ), t h e m o m e n t a m p l i f ic a t io n f a c t o r in e q n ( 12 ) c a n b e
r e wr i t t e n a s
1A F =
I _ ( E Pu + ~" CL Pu )Z'~L (14)
T h i s e q u a t i o n i s n o t e x a c t ly e q u a l t o e q n ( 11 ). I n f a c t , it c a n b e sh o wn f r o m
L e Me ssu r i e r ' s d e r i v a t i o n t h a t t h i s i s t h e a m p l i f i c a t i o n f a c t o r f o r t h e
f i rs t -o r d e r l a t e r a l d isp l a c e m e n t s . H o w e v e r , t h e C L f a c to r , w h i c h r a n g e sf r o m 0 t o 0 . 2 1 6 , i s u su a l ly sm a ll f o r c o lu m n s i n u n b r a c e d f r a m e s a n d m a y
b e i g n o r e d i n m a n y p r a c t i c a l d es i g ns . Ne g l e c t in g t h e C L t e r m i s e q u i v a l e n t
t o d i s r e g a r d i n g m e m b e r c u r v a t u r e P - 8 e f fe c ts o n t h e a m p l if i ca t io n o f t h e
f i r s t - o r d e r s w a y d i s p l a c e m e n t s a n d b e a m - c o l u m n e n d m o m e n t s . T h e
m o m e n t a m p l i f i c a t i o n f a c t o r s g i v e n b y e q n s ( 1 1 ) a n d ( 1 4 ) b e c o m e
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 18/40
286 J. Y. Richard Liew, D. W. White, W. F. Chen
equivalent as CL approaches zero. It is important to note that, if CL is
assumed equal to zero, then these equations are identical to the expression
for BE given by eqn (H1-5) of LRFD.
Equations (10) and (11) account accurately for the fact that all the
columns in a story participate in any side-sway buckling mode, and that the
stronger columns with a smaller L ~ ratio brace the weaker columns
with a larger L V ~ u / E I until side-sway buckling occurs. Also, they account
directly for cases in which there are gravity or leaner columns in the story.
An iterative procedure which enables the calculation of inelastic K factors
is also outlined by LeMessurier. 10 Interested readers should refer to this
reference for details. The basic concept of inelastic stiffness reduction
employed by LeMessurier is the same as that of the LRFD procedure
described in Section 4.1 with one exception. LeMessurier's inelasticstiffness reduction is based on the value of Et/E at incipient inelastic
buckling whereas the LRFD procedure is based on Et/E at the factored
load level Pu. If P~ is smaller than the axial load in the column associated
with inelastic buckling, then LeMessurier's procedure results in a smaller
value of Et/E and thus smaller inelastic K factors. This is usually the case
for beam-columns subjected to significant bending action. An iterative
alignment chart procedure also exists for determining inelastic K factors.
This procedure was originally proposed by Yura, 1~ and it is also based onEt/E at incipient inelastic buckling.
It can be argued that the inelastic buckling strength Pn should be
calculated based on Et/E at incipient inelastic buckling. However, this
calculation is necessarily iterative. Also, questions arise with regard to
how a general frame which is subjected to design loads resulting in bending
action should be loaded to calculate this inelastic buckling load. The
simpler and direct LRFD method (based on eqns (8) and (9)) under-
estimates Et/E, and thus it overestimates K when there is significantbending action. This results in a conservative value for P,. In recent work,
Goto et al.12 have provided a refined method of analysis for the elastic
buckling of rigid frames. The method considers primary bending and
member bowing effects. Of course, calculation of the actual member
forces in a frame requires a second-order inelastic analysis of some type.
4 . 3 M o d i f i e d K f a c to r m e t h o d ( b a s e d o n t h e b u c k l i n g o f a st o r y )
A modified K factor may be calculated by assuming that the sum of the
axial loads which causes sway buckling of a story is equal to the sum of the
individual buckling loads for each of the columns which provide story
side-sway resistance. The individual buckling loads are determined using
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 19/40
Be am -colu m n design in steel~rameworks 287
t h e e f f e c ti v e l e n g t h s f r o m t h e a l i g n m e n t c h a r t . T h e r e f o r e , a t th e b u c k l i n g
o f a s t o r y , we h a v e
AsE P . = E Pek (15)
w here As i s t he s to ry buck l ing load fac to r . Th e c or re sp ond ing ax ia l l oad in
a n y c o l u m n i t h a t p a r t ic i p a t e s i n t h e r e s is t a n c e t o s t o r y b u c k l in g is g iv e n b y
CEIiA s P ui = ( K i L i ) 2 ( 1 6 )
El im ina t ing As f rom eqn s (15) an d (16) g ives
n 2 E l i E Pu (17)K 2 = ~ u i X Pek
T h i s e q u a t i o n i s a s i m p l i f i e d f o r m o f L e Me ssu r i e r ' s f o r m u l a ( e q n ( 1 0 ) )
s ince i t neg lec t s t he con t r ibu t io n o f t he CL t e rm. A l so , i t s use does no t
requ i re L X/~ , /E- I t o be iden t i ca l fo r a l l t he co lumns . Hence , i t i s an
i m p r o v e m e n t o v e r t h e a l i g n m e n t c h a r t m e t h o d f o r d e t e r m i n i n g t h e
e f fec t ive l eng th used in ca l cu la t ion o f t he co lumn s t reng th Pn . E f fec t ive
l eng th fac to r s such as those o b ta in ed f ro m e qns (10) o r (17) a re e ssen t i a l
f o r p r o p e r c a l c u la t io n o f Pn f o r m e m b e r s o f t h e l a t e r al - re s i s ti n g sy s t e m i nl e a n e d c o l u m n f r a m e s . I n e l a s ti c K f a ct o r s c a n b e c o m p u t e d f r o m e q n ( 1 7)
i f t he X Pek t e rm i s ca l cu la t ed base d on the ine l a s t ic G fac to r exp ressed b y
eqn s (7 ) to (9 ) and I i i s r ep laced by E t I i / E , i n wh i c h E t / E m a y b e c a l c u l a t e d
f r o m e q n s ( 8 ) a n d ( 9) f o r e a c h c o l u m n .
A s t o r y m o m e n t a m p l i f i c a t i o n f a c t o r m a y b e o b t a i n e d b y su b s t i t u t i n g
the e l a s t i c K fac to r f rom eq n (17) in to eqn (13) , and th en sub s t i t u t ing P¢i
f rom eqn (13) in to eqn (12). Th i s r e su l t s i n the fo l lowing s imple equ a t ion :
m F ~1 1
[ Pu i = Y+P u1 ( 1 8 )
T h a t i s , t h e A F v a l u e o b t a i n e d f r o m t h e a b o v e p r o c e d u r e i s i d e n t ic a l t o t h e
B 2 v a l u e o b t a i n e d f r o m e q n ( H1 - 5 ) o f th e L R F D Sp e c if ic a ti o n w i t h t h e u se
o f a l i g n m e n t c h a r t K f a c to r s . T h e r e f o r e , t h e u se o f m o d i f ie d K f a c t o rs i n
e q n ( H1 - 5 ) o f t h e L R F D Sp e c i fi c at io n i s n o t n e c e s sa ry . I n m a k i n g t h i s
a s se s sm e n t , i t i s i m p o r t a n t t o r e c o g n i z e t h a t , i f t h e a l i g n m e n t c h a r t
p ro ced ure i s used fo r ca l cu la ting Be , s to ry sum m at ion o f t he Pu /Pek t e rm s i s
r e q u i r e d a n d t h e Pe k v a l u e f o r a l e a n e d c o l u m n m u s t b e t a k e n a s z e r o .
H o w e v e r , i f t h e m o d i f ie d K f a c t o r e q u a t i o n s a r e u se d i n s t e a d o f t h e
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 20/40
288 J. Y. Richa rdLiew , D . IV. Wh ite, W . F. Ch en
a l i g n m e n t c h a r t K v a l u es , n o s t o r y su m m a t i o n i s n e c e s sa ry ( a n d t h e e e i
t e r m f o r a l e a n e d c o l u m n is th e f in i te v a lu e o b t a i n e d b y su b s t i tu t i o n o f e q n
(17) in to eqn (13) fo r t he l eane d co lum n me m ber ) . Th i s is because the
s to ry e f fec t s hav e be en inc luded in the m odi f ied K fac to r , wh ich is de r ived
b a se d o n t h e c o n c e p t o f s t o r y b u c k li n g .
Th e A us t ra l ia n AS 4100 Spec i f ica t ion 13 spec i f ies an am pl i f ica t ion of
f i rs t -o rde r sway m om ent s tha t i s s imi l a r t o eq n (18) :
A F =
0.9
1 - ( E P uEPcr ) (19)
T h e Z P c r t e rm in th i s equ a t ion i s de f ined ge ne r i ca l ly a s the s to ry e l a s t i c
buck l ing load . Eq ua t ion (19) i s app l i cab le wh en E Pu /'Z P ~ i s be tw een 0 .1
an d 0 .25. F or Y. Pu/E Pc~ < 0 .1 , th e P - A effec t i s sm al l an d hen ce can be
n e g l e c te d . Fo r Z P u / ~ Pe r > 0 "2 , a s e c o n d - o r d e r i n e la s t ic a n a l y s is is
r e c o m m e n d e d . I t s h o u l d b e n o t e d t h a t in th e A u s t r a li a n p r o c ed u r e , b o t h
t h e c o lu m n a n d b e a m e n d m o m e n t s a r e a m p li fi ed w h e r e a s in th e L R F D
e f f e c t i v e l e n g t h a p p r o a c h , o n l y t h e a m p l i f i c a t i o n o f t h e b e a m - c o l u m n
m o m e n t is e x p l ic i tl y r e q u i r e d . T h e a u t h o r s b e l i e v e t h a t t h is a p p r o a c h t o
t h e a m p l i fi ca ti o n o f th e b e a m m o m e n t s s h o u l d b e e x t e n d e d t o t h e L R F DSpec i f ica t ion p roced ure a s we l l.
4 . 4 B u c k l i n g a n a l y s i s o f th e o v e r a ll s tr u c t u r a l s y s t e m
The e f fec t ive l eng th fac to r s may a l so be ca l cu la t ed f rom a buck l ing
ana lys i s o f t he en t i r e s t ruc tu ra l sys t em . Th i s is accom pl i shed by equ a t ing
the ax ia l fo rce in a m em ber a t the inc ip i en t buck l ing o f t he f ram e , Per, to
the buck l ing load a ssoc ia t ed wi th an e f fec t ive l eng th K L . T h e r e su l t i n ge la s ti c e f fec t ive l eng th fac to r i s de t e rm ined a s
~ f P e ~ f ~.2 E I / L 2K = -ff~ = (20)
A n ine la s t ic K fac to r can be c om pu ted f rom e qn (20) i f Per i s ca l cu la t ed
based on ine l a s t ic buck l ing ana lys is and I i s r ep laced by E t l / E fo r t he
p a r t ic u l a r m e m b e r u n d e r c o n s i d er a ti o n .T h e u se o f t h e b u c k l i n g l o a d a n a l y s is f o r a f r a m e w o r k l e a d s to a n o t h e r
p o s s i b le f o r m o f t h e m o m e n t a m p l i fi c a ti o n f a c to r ,
1Av = 1/A----~ (21)
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 21/40
B e a m - . c o l u m n d e s i g n i n t ee l r a m e w o r k s 2 8 9
where Afis the ratio of the elastic buckling load of the entire frame to the
factored load of the frame.In rectangular unbraced frames, the story moment amplification factor,
based on eqn (18), often gives a better prediction of the second-orderelastic moments than the frame moment amplification factor shown in eqn
(21). This is because the amplification effects are not the same for each and
every story throughout the entire framing system. For instance, stories
that are more stiff or more lightly loaded will have smaller amplification
effects than stories that are more flexible and heavily loaded. However,
the frame moment amplifier is applicable for non-rectangular and
irregular frames, and for structures with a mixture of elements providing
restraint against side-sway. For general frames, a buckling analysis of the
entire frame is necessary for accurate determination of the effective length
factors to be used in the axial resistance term of the beam-column design
formulas. The use of the system buckling analysis may lead to unexpected-
ly large K values for members that are lightly loaded (i.e. for members
having small design axial forces). In fact, for a column with zero axial load
Pu, the K factor calculated from eqn (20) is infinity. This results in an
indeterminate form of the axial strength ratio, Pu/Pn = 0/0. However, it
can be shown by algebraic manipulation that the first term of the
beam-column interaction equation (eqn 2) has a finite value of
P~ 1
P---~- = 0-877-----~ (22)
for this case. Equation (22) is derived by writing P~ in eqn (20) both as
Per = Pn/0"877 and Pcr= AfPu for this case. By equating these two
expressions, solving for Pu, and substituting this value into Pu/Pn, the
result shown by eqn (22) is obtained.
If the LeMessurier or the modified K factor procedures are employed
(eqns 10 or 17), a similar situation occurs in the limit as the column axial
force approaches zero. In general, the first term of the beam-column
interact ion equation approaches the value of
Pu 2 2Pu i L i K i
Pn - 0-877 ~r2EIi (23)
for these procedures a s P u i approaches zero. By substituting either eqn 10or eqn 17 into this expression, an expression which is independent of Pui isobtained.
The rationale for the first term of the interaction equations being taken as
the values given by eqn (22) or (23), even if a beam-column has nearly zero
axial force, is that the member may contribute to the buckling resistance of
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 22/40
290 J . Y . Rich ard Lie w , D . IV. W hi te , W . F. Chen
structural system by providing restraint to other members. 14 Yet, in many
cases it can be said that the members which have small axial forces and
large effective lengths from a system buckling analysis are actually not
participating in the buckling of the system at all, and therefore, the systembuckling load will be changed little if the size of these members is changed.
In this case, one might rationalize that such a member 's effective length
should be based on the buckling analysis of an isolated subassemblage of
the frame that includes the lightly loaded member (i.e., it should be based
on a procedure such as the alignment chart method). The member 's K
factor would be smaller if determined in this way. This would be the case
for the beam-columns in the top story of the multi-story frame example
discussed in the next section (see Fig. 11). However , in some situations, a
member may have a large K factor from the system buckling analysis
because it is restraining other more critically loaded members at incipient
buckling of the overall system. If this restraint is counted upon in the
design of the more critical members, then the larger K factor from the
system buckling analysis must be utilized for the more lightly loaded
members.
4 .5 Cha rac ter is t ic re su l t s o f K fac tor ca l cu la t ions
Figures 9 and 10 show the column K factors, computed for two simple
portal frames using the methods described in the previous sections. These
frames have fixed and p inned bases respectively. The results are presented
for G values associated with a range of rigid to very flexible beam
restraints, and also for several values of a, which is defined as the ratio of
the axial loads on the columns. For these examples, eqns (10) and (17)
predict the same variations of the K factor for different values of a. These
equations correspond to LeMessurier's method and the modified K factormethod respectively. Although the curves shown in Figs 9 and 10 have
been developed for the right-hand column in these frames (column CD),
the same curves can also be used for the left-hand column (column AB)
simply by replacing a by 1/%Fa.
It should be observed that the K factors predicted by eqns (10) and (17)
are affected by the load distributions in the columns. The column carrying
the smaller axial load has a larger K factor than the column carrying the
higher axial load. This is due to the fact that the column with the low axial
force effectively braces' the column that has the high axial force until story
buckling occurs. Also, it should be noted that the column with the larger
axial load may have a K factor less than 1.0. When both columns in the
frame carry the same load (i.e., for a = 1-0), the K factors obtained from
eqns (10) and (17) coincide with the K factors obtained from the alignment
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 23/40
Be am -co lum n des ign in s tee tf rameworks 291
2 .5
2 .2
1.9
KCO
1.6
1.3
1.0
0 .7
ecp l P 4.0
T . e z b t D '~ =
I I
0 1 2 3 4 5
G = ( I c / L e ) / ( l b / L b )
Fig . 9 . Charac te r i s t i c re su l t s o f K fac tors for por ta l f rames wi th f ixed base condi t ions .
E q ua t i ons ( 10 ), ( 17 ) a nd ( 20) g i ve i de n ti c a l r e su l t s a nd s how a va r i a t ion o f t he K f a c t o r f o r
d i f f e r e n t a va l ue s . T he K va l ue s ob t a i ne d f r om t he a l i gnm e n t c ha r t p r oc e du r e do no t
acco unt fo r va r i a t ions in c~.
chart method. However, the alignment chart method (eqn 4) is not at all
applicable when a is not equal to 1.0. This is due to the fact that the
alignment chart is based on the explicit assumption that all the columns inthe structural system have the same stiffness parameter (L ~ / ) at
incipient buckling.
Although the assessment of the stability of an unbraced frame must
consider the total buckling strength of each individual column in the story,
there is one limitation; that is, a column cannot carry a load higher than its
own capacity in a non-sway mode. If this is the case, the K factor calculated
based on the story buckling formulae should not be less than that from the
side-sway prevented case.In practical building design, the columns within a frame seldom have the
same stiffness parameter. Figure l l a shows the member sizes, dimensions,
and working loads for a bent of a 10 story building frame. It is assumed that
the spacing between bents is 20 ft (6096 ram). The elastic K factors for the
columns of this frame are reported based on a system buckling analysis in
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 24/40
292 J. Y. Richard Liew, D. W. White, W. F. Chen
V5 .5 ~ ~ = 4 , 0
| ~ P p
jo
4 . 5
4 .0
KC D
3 .5
3 . 0
2 . 5
2 .0
1.5 I L I I I
0 1 2 3 4 5
G = ( I c / L c ) / ( I b / L b )
Fig. 10. Characteristic results of K factors for portal frames with hinged base conditions.
Equations (10), (17) and (20) give identical results and show a variation of the K factor fol
different a values. The K values obtained from the alignment chart procedure do not
account for variations in a.
Fig. 11b, and based on the alignment chart method in Fig. 11c. It is
observed that the discrepancy in the K factors is quite high for some of thecolumns.
The difference in K factors is particularly large for the columns in thebottom and the top stories. This is because the fundamental assumptions
of the alignment chart K factor have been violated in these members.
Typically, the members with smaller axial forces from the system buckling
analysis have larger K values. It is interesting to note that changes in thesize of the members which have large K values often have little effect onthe overall System buckling load.
Figure 12 shows an unbraced frame with columns of unequal lengths. A
buckling analysis of this frame has been performed for column lengthratios, 7 = LAB/Lco, ranging from 1.0 to 4.0. Equal axial loads are
applied at the top of each column. For this frame, eqns (10) and (17)predict essentially the same elastic K factors for all the cases considered.
Prior to story buckling, the shorter column braces the longer column, and
thus the shorter column has a larger effective length factor. The use of the
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 25/40
B eam--colum n design n teel r am ewor ks 2 9 3
R o o f t o a d
Live (L r ) 1437 KN /m 2
D e a d (O) 2.395 KN /m =
Floor load
Live (L) 1.916 KN /m 2
Dead (E)) 2.634 KN /m 2
E xte r ior w a l l (story)
= 423KN or1 exter ior
columns
Fac tor ed load
= 1 2D + 16L +0.SL r
Ia ; •
N14x2;
~ do
i ~12x2~~ do1
W16X20
d o
W14x3Q
do
I ! 3 @ 6 0 9 6 m m
2.98
1.83
2.55
2.16
2.43
2.20
2.40
2,24
2.29
2.16
2.05 2.06 2.93 t. 15 1.16 1.37
1.42 1.42 1.83 1.34 1,34 1.67
2.27 2.27 2.55 1.59 1.59 2.05
1.96 1~96 2.16 1.75 1.75 2.35
2.00 2.00 2.43 1.33 1.83 2.59
1.63 1.83 2,20 1.34 1.84 2,59
2,23 2.23 2.40 190 1.90 2,57
2.09 2.09 2.24 1.97 1.99 2.71
1.95 1.95 2.29 1.98 ! 1.98 2,81
( a ) ( b ) ( c )
F i g . 1 1 . ( a ) D i m e n s i o n s , l o a d s , a n d m e m b e r s i z e s f o r a 1 0 - st o r e y 3 - b a y f r a m e ; ( b ) K fa c t o r s
f r o m s y s t e m b u c k l i n g a n a l y s is ; ( c ) K f a c t o rs f r o m t h e a l i g n m e n t c h a r t m e t h o d .
K
B I b D
I G = ( I/Lc /( lb /L )3 .0 i c i c K ~ = K C D / ¥
C o lu m n ~ fi~ 13 m ~ - s ~ y m o d e
A L b G = 5 . O
• olumn CD
~ l ~ - - ~ f ~ J ' ~ ~ o 5.o":'!:°"'°"5 ..~o.o--2.0 } C o l u m n A B
0 .5 1 .0 0 .5 0 .0
C o lu m n A B f a i b i n n o n - s w a y m o d e
O.0 I I I I1 . 0 1 , 6 2 . 0 2 , 1 i a . 0
~ = L e q t h A B / L m s t h C D
F i g . 1 2 . C h a r a c t e r i st ic K f a c t o r r e su l t s f o r p o rt a t f r a m e s w i t h u n e q u a l c o l u m n l e n g t h s .
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 26/40
294
8
J. Y. Richard Liew, D. W. White, W. F. Chen
K C D
o r = 4 . 0a p p L e M e s s u r i e r { E q n . l O ) , ~
~ B [ b ~ D . . . . M o d i f i e d K ( E q n . 1 7) , . ~ ' ~ ; ' ~
. S 20
.,, " " ~ ~ 1.0
, o . ¢ " ~ ~ . s ~ " , ~
o , , . ., " ~ 0 . 5
" ~ " ~ d 0. 0
0 1 2 3 4 5
G = ( l c / L c ) / ( I b / 2 L b )
Fig. 13. Ch aracteristic K facto r results for leaned -colum nframes.
a l i g n m e n t c h a r t i s s tr ic tl y a p p l ic a b l e o n l y w h e n t h e s ti ff n es s p a r a m e t e r s o f
b o t h c o l u m n s a r e t h e s a m e . I t c a n b e o b s e r v e d f r o m F i g . 1 2 t h a t t h e d i r e c t
u s e o f t h e a l i g n m e n t c h a r t w i t h o u t a n y m o d i f i c at io n w il l u n d e r e s t i m a t e t h e
K f a c t o r f o r c o l u m n C D a n d o v e r e s t im a t e th e K f a c t o r f o r c o l u m n A B .H e n c e , c o l u m n C D ' s c o n t r i b u t i o n t o t h e s t r e n g t h o f t h e s y s t e m w i l l b e
o v e r - p r e d i c t e d w h e r e a s c o l u m n A B ' s c o n t r i b u t i o n w il l b e u n d e r p r e d i c t e d .
A s p e c ia l c o n c e r n o f th e w r i te r s w i th r e g a r d t o t h e p r o p e r c a l c u l a t io n o f
K f a c t o r s is t h e c a s e o f l e a n e d c o l u m n f r a m e s , i n w h i c h a l a r g e n u m b e r o f
c o l u m n s a r e p r o v i d e d o n l y f o r g r a v it y l o a d s a n d d o n o t p a r t ic i p a t e i n t h e
l a t e r a l - f o r c e r e s is t in g s y s te m . T h e s e t y p e s o f f r a m e s a r e q u i t e c o m m o n f o r
s o m e t y p e s o f l o w - r i s e i n d u s t r i a l b u i l d i n g s a s w e l l a s f o r t a l l o f f i c e - t y p e
b u il d in g s . T h e e f fe c t i v e l e n gt h s o f l e a n e d c o l u m n s s h o u l d b e c o m p u t e d
b a s e d o n K = 1. I n o t h e r w o r d s , t h e b e a m - c o l u m n s o f t h e la t e r al - re s i st in g
s y s te m a r e c o u n t e d u p o n t o b r a c e t h e l e a n e d c o l u m n s a t e a c h f lo o r l ev e l.
D u e t o t h e d e s t a b i l i z i n g a c t i o n o f a x i a l f o r c e s a c t i n g o n t h e l e a n e d
c o l u m n s , t h e e f f e c ti v e l e n g t h s o f th e b e a m - c o l u m n s i n t h e l a te r a l- r e s is t in g
s y s t e m a r e i n c r e a s e d . T h i s e f f e c t is i l l u s t ra t e d b y t h e p o r t a l f r a m e s h o w n i n
F i g . 1 3 . T h e p a r a m e t e r a i n t h e f i g u r e is t h e r a t i o o f t h e a x i a l l o a d a p p l i e d
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 27/40
Beam -column design in steel ramew orks 295
t o t h e l e a n e d c o l u m n o n t h e l e f t s i d e o f t h e f r a m e t o t h a t o f th e l a te r a l -l o a d
r e si st in g c o l u m n o n t h e r ig h t s id e . T h i s f r a m e i s e q u i v a l e n t t o a m o r e
g e n e r a l f r a m e w h i c h h a s a l e a n e d c o l u m n s , e a c h w i th a lo a d e q u a l t o P .
T h e s e c o l u m n s a r e ' b r a c e d ' b y t h e s o l e l a te r a l- l o a d re s is t i n g c o l u m n ,
c o lu m n C D .
T h e K f a c to r s o b t a i n e d f r o m L e M e s s u r i e r 's m e t h o d a s w e l l a s f r o m t h e
m o d i f i e d K f a c to r m e t h o d a r e s h o w n i n t h e f ig u re . F o r t h is p r o b l e m ,
L e M e s s u r i e r 's m e t h o d ( e q n ( 1 0) ) g iv e s t h e m o r e a c c u r a te e l a st ic K f a c to r s,
w h e r e a s t h e m o d i f i e d K f a c to r m e t h o d ( e q n ( 1 7) ) alw a y s gi v es a
c o n s e r v a t i v e p r e d i c t i o n o f K ( i .e . , i t g i v e s a l a r g e r K ) . T h e a l i g n m e n t c h a r t
m e t h o d is o n ly v a li d fo r t h e c a s e w h e r e t h e a x ia l l o a d i n th e l e a n e d c o l u m n
is e q u a l t o z e r o (i . e . , a = 0 - 0) . A n y a t t e m p t t o u s e t h e a l i g n m e n t c h a r t t o
c a l c u l a te t h e K f a c t o r s fo r a o t h e r t h a n 0 -0 w i ll l e a d t o u n c o n s e r v a t i v er e s u lt s. T h e e x i s t e n c e o f la r g e a x ia l f o r c e s i n t h e l e a n e d c o l u m n ( o r o f a
l a rg e n u m b e r o f l e a n e d c o l u m n s ) r e su l ts i n l ar g e d i ff e r e n c e s i n t h e
c a l c u la t e d K f a c to r a n d h e n c e a l a rg e d i f f e r e n c e b e t w e e n t h e r e su l ts
o b t a i n e d b y t h e a l i g n m e n t c h a r t a n d t h e m o r e e x a ct m e t h o d s . T h is e f fe c t
w o u l d a l so b e e x h i b i t e d fo r a n y f r a m e i n w h i c h a la r g e n u m b e r o f le a n e r
c o l u m n s a r e r e s t r a i n e d a g a i n s t s i d e -s w a y b y o n l y a f e w c o l u m n s .
5 T H E U S E O F E F F E C T I V E L E N G T H F A C T O R S W I T H T H E
L R F D B E A M - C O L U M N E Q U A T I O N S
F i g u r e 1 4 s h o w s a s y m m e t r ic p i n n e d - b a s e p o r t a l f r a m e w i th e q u a l v e r t ic a l
l o ad s a t t h e t o p o f th e c o l u m n s . T h e L R F D i n te r a c ti o n e q u a t i o n s a r e
e v a l u a t e d f o r th i s p r o b l e m u s i n g b o t h t h e e l a st ic a n d t h e i n e l a s t ic K f a c t o r s
f r o m t h e a l i g n m e n t c h a r t m e t h o d . T h e i n el a st ic K f ac to r s a re e v a l u a t e d
b a s e d o n t h e L R F D M a n u a l p r o c e d u r e ( e q n s ( 8) a n d (9 )) . T h e r e s is ta n c ef a c to r s q ~ a n d ~bc i n th e L R F D e q u a t i o n s a r e t a k e n a s u n i t y t o o b t a i n t h e
n o m i n a l b e a m - c o l u m n s t r e n g t h . T h e i n e l a s t i c s t r e n g t h c u r v e s f o r t h e s e
f r a m e s w e r e g e n e r a t e d b y K a n c h a n a l a i , 4 a s s u m i n g try = 2 5 0 N / r a m 2,
E = 2 0 0 0 0 0 N / m m 2 a n d trr¢ = 0 -3 try . A l l t h e m e m b e r s a r e a s s u m e d t o b e
p e r f e c tl y s tr a ig h t a n d p l u m b i n K a n c h a n a l a l ' s s tu d y .
K a n c h a n a l a i ' s r e s u l t s a r e s h o w n i n t h e f i g u r e f o r b o t h s t r o n g - a n d
w e a k - a x i s b e n d i n g a n d f o r c o l u m n s h a v i n g sl e n d e r n e s s ra t io s o f L / r = 2 0
a n d 4 0 . T h e c u r v e s s h o w n a r e n o t a d j u s t e d t o a c c o u n t f o r i m p e r f e c t i o n
e f f ec t s .
T h e L R F D c u r v e s, a s s h o w n in F ig . 1 4 , a r e g e n e r a l ly c o n s e r v a t i v e
c o m p a r e d t o t h e i n e l a s t ic s t r e n g t h c u r v e s . T h i s is p a r t l y d u e t o t h e f a c t t h a t
t h e L R F D b e a m - c o l u m n e q u a t i o n s i m p l ic i tl y i n c l u d e t h e e f f e c t o f in i ti a l
g e o m e t r i c i m p e r f e c t i o n s . H o w e v e r , t h e d i f f e r e n c e b e t w e e n t h e i n e l as t i c
s t r e n g t h c u r v e s a n d t h e L R F D s t r e n g t h c u rv e s is q u i t e la r g e fo r a s h o r t
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 28/40
2 9 6 J. Y. Richard Liew, D. W. White, W. F. Chen
P
P y
1.0
0 .8
0 .6
0 .4
0 .2
l b
Lb w,#
\
~ m
G A = ( l c / L e ) / ( [ b / L b ) = 3 . 0
G B = 0
\\
J
L / r = 4 0 / " ~ .
S t r o n g a x i s
} ( K a n c h a n a l a i ,1 9 7 7 )W e a k a x i s
L R F D e l a s t i c K ( E q n s . 1 - 2 , 4 - 6 )
L R F D i n e la s t i c K ( E q n s . 1 - 2 , 4 , 7 - 9 )
L / r = 2 0
\
\
\
\ \
\
t I I I
0 . 0 0 . 2 0 . 4 0 . 6 0 . 8 1 . 0
H L c / 2 M p
Fig. 14. Effect of using elastic and inelastic K factors on th e AISC -LRF D beam-colum nequations.
c o l u m n b e n t a b o u t t h e w e a k a xis , p a r t ic u l a r l y f o r c o l u m n s s u b j e c t e d t o
l ow a xia l l o ad . T h i s is p r im a r i ly b e c a u s e t h e L R F D b e a m - c o l u m n
i n t e r a c t i o n c u r v e s d o n o t d i s ti n g u is h b e t w e e n s t ro n g - a n d w e a k - a x i s c a s es .
T h a t i s , th e r e i s o n l y o n e n o r m a l i z e d L R F D b e a m - c o l u m n s t re n g t h cu r v e
f o r a g i v e n L/r. H o w e v e r , t h e a c t u a l s t r e n g t h s f o r st ro n g - a n d w e a k - a x is
b e n d i n g a r e d i ff e r en t • N e v e r t h e l e s s , t h e u s e o f o n l y o n e i n t e r a c t i o n
e q u a t i o n f o r s t r o n g - a n d w e a k - a x is b e n d i n g i s c o n s i s t e n t w i t h t h e u s e o f
o n l y o n e c o l u m n s t r e n g t h c u r v e f o r a xia l st r en g t h •
C l o s e e x a m i n a t i o n o f F i g . 1 4 a l so r e v e a l s t h a t t h e u s e o f t h e i n e l a s t i c K
f a c t o r ( c a lc u l a t e d a c c o r d i n g t o t h e p r o c e d u r e in S e c t i o n 4 . 1) i n t h e L R F D
e q u a t i o n s is o n l y b e n e f i c i al fo r s h o r t c o l u m n s s u b j e c t e d t o h i g h a x ia l l o a d s •
T h e r e is e s se n ti a l ly n o d i f f e r en c e b e t w e e n t h e L R F D c u r v es b a s e d o n
e l a s t ic a n d i n e l a s t i c K f a c t o r s f o r t h e L/r = 4 0 c a s e . T h i s is e x p e c t e d s i n c e
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 29/40
Beam--column e s i g n n teel rameworks 297
P
P y
t.O
0. 8
0 .6
0.4
0.2
H ~ ° t P l b : o o ~ P
c l
~ .~ Lb ~1
Q = 3 . 0
G A = 0
G B = ~ o
L / r = 2 0
S t r o n g a x i s ~W e a k a x i s J ( K a n c h a n a la i , 1 9 7 7 )
~ . ~ L R F D e l a s t ic K ( E q n s . 1 - 2 , 1 0 - 1 1 )
. . . . L R F D e l a s ti c K ( E q n s. 1 - 2 , 1 7 - 1 8 )
\\
\
\f . X . . \ . = o o
\
, \
0 . 0 0 . 2 0 . 4 0 . 6 0 . 8 1 .0
H L c I M p
Fig. 15. Comparisonof the AISC-LRF D beam-column quat ionswith ult imatestrengthcurves4 for leaned -colum n ram e w ith GA ---- 0 and L /r -- 20.
t h e i n e l a st ic K f a c to r is u s e d o n l y i n t h e a x ia l r es is t a n c e te r m o f t h e L R F D
e q u a t i o n s . H e n c e , i t o n l y a f f ec t s c o l u m n s s u b j e ct e d to p r e d o m i n a n t l y
a x i a l l o a d s . N e v e r t h e l e s s , i n fr a m e s w h i c h h a v e b o t h h e a v i l y lo a d e d a n d
l ig h t l y l o a d e d b e a m - c o l u m n s , th e i n e l a s ti c K f a c t o rs o b t a i n e d b y L e M e s -
s u r i e r ' s m e t h o d , t h e m o d i f i e d K f a c t o r m e t h o d , o r b y s y s t e m b u c k l i n g
a n a l y s i s c a n b e s i g n i fi c a n t ly d i f f e r e n t th a n t h e c o r r e s p o n d i n g e l a s t ic K
v a l u e s . T h i s i s p a r t ic u l a r l y t h e c a s e a t i n c i p i e n t i n e l a s t i c b u c k l i n g . I f
i n e l a st ic st if f n e ss r e d u c t i o n is e m p l o y e d w i th t h e s e m e t h o d s , t h e e f f e c t i v e
l e n g t h s f o r c o l u m n s w h i c h e x h i b i t s i g n if ic a n t y i e ld i n g w i l l t e n d t o b e
s m a l le r , a n d t h o s e f o r c o l u m n s w h i c h r e m a i n p r e d o m i n a n t l y e l a s ti c w i l l
t e n d t o b e l ar g e r. T h u s , t h e u s e o f i n e l a s ti c s t if fn e s s r e d u c t io n w i t h t h e s e
m e t h o d s p r o p e r l y a c c o u n t s f o r t h e f a c t t h a t t h e e l a s t i c c o l u m n s t e n d t o
r e s t r a in t h e i n e l a s t i c c o l u m n s a g a i n s t s i d e - s w a y i n s ta b i l it y .
A n i m p l i c it a s su m p t i o n o f u s i n g t h e i n e l a s ti c K f a c to r f o r c o l u m n d e s i g n
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 30/40
298 J . Y . Richard L iew, D . W . W h i te , W . F . Chen
T.0 ~-
0 . 8
P
Py
0 .6
0 .4
0 .2
H
L . . L b
P
A
lc
B
G A = 0
G B = o o
L / r = 4 0
~ m
m B !
S t r o n g ax is )( K a n c h a n a l a i , 1 9 7 7 )
W e a k a x i s )
LRFD e l a s t i c K ( E q n s . 1 - 2 , 1 0 - 1 1 )
L R F D e l a s t i c K ( E q n s , 1 - 2 , 1 7 - 1 8 )
= 0.0
a = 2 .0
Fig . 16 .
0 .0 0 .2 0 .4 0 .6 0 .8 1 .0
H L c / M p
Comparison of the AISC-LRFD beam-column equat ions wi th the ul t imates t r e n g t h c u r v e s 4 for leaned-co lum n fram e with G A = 0 and L / r = 4 0.
i s th a t t h e c o l u m n is lo a d e d i n t h e i n e l a s ti c r a n g e w h i l e t h e s u r r o u n d i n g
m e m b e r s r e m a i n e la s t i c . T h i s a s s u m p t i o n i s a d e q u a t e f o r e la s t i c a n a ly s i s /
d e s i g n s i n c e t h e c a p a c i t y o f th e s t r u c tu r a l s y s t e m is i m p l ic i t ly t a k e n a s t h e
l o a d a t w h i c h t h e m o s t c r it ic a l m e m b e r r e a c h e s i ts l i m i t s ta t e . H o w e v e r , i f
p l a s t ic h i n g e f o r m a t i o n i n th e b e a m s a n d s u b s e q u e n t i n e l a s t i c r e d is tr ib u -
t i o n o f fo r c e s is r e l ie d u p o n , a s in p l a s ti c d e s i g n , t h e i n e l a s t i c K f a c t o r
c o n c e p t i s n o t s tr i c t l y a p p l i c a b l e . I n f a c t , t h e u s e o f t h e e l a s t i c K f a c t o r s t oa c c o u n t f o r s t a b i l i t y a s p e c t s i n i n e l a s t i c a n a l y s i s / d e s i g n i s a l s o n o t f u l l y
r a t io n a l . T h e r e f o r e , i f s o m e f o r m o f in e l a s t i c a n a ly s i s / d e s ig n i s e m p l o y e d ,
t h e p r o p e r a c c o u n t i n g o f s ta b i li ty e f f e c t s s h o u l d b e c a r e f u l ly c o n s i d e r e d .
O b v i o u s l y , d i r ec t c o n s i d e r a t i o n o f s t a b i li ty e f f e c t s i n s o m e f o r m o f
s e c o n d - o r d e r i n e l a s t i c a n a l y s i s i s t h e u l t i m a t e s o l u t i o n .
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 31/40
B eam--co lum n design n teel ram ewor ks 299
P
1.0
0 . 8
0 .6
0 .4
0 .2
H ~ o tp J .b
l c
L.. Lb
(~ = 3.0
Ic
G A = ( l c / L c ) / ( | b / 2 L b) = 4 .0
G B = O ~
L / r = 2 0
S t r o n g a x i s ). ( K a n c h a n a l a i , 1 9 7 7 )
~ - - W e a k a x is J
- - . - - L R F D e l a s t i c K ( E q n s . 1 - 2 , 1 0 - 1 1 )
L R F D e l a s t i c K ( E q n s . 1 - 2 , 1 7 - 1 8 )
~ ot = 0 .0
\
\
0 . 0 0 . 2 0 . 4 0 . 6 0 . 8 1 .0
H L c ] M p
F i g . 1 7 . Comparison o f t h e A I S C - L R F D b e a m - c o lu m n equations w i t h t h e u l t i m a t e
s t r e n g th c u r v e s 4 f o r l e a n e d - c o lu m n f r a m e wi th GA ---- 4 a nd L/r = 20.
T h e L R F D e q u a t i o n s a r e f u r th e r i n v e s t ig a t e d i n F i g s 15 t o 1 8 b yc o m p a r i n g th e p r e d i c t e d st r en g t h o f a b e a m - c o l u m n i n a l e a n e d c o l u m n
f r a m e w i t h t h e r e s u lt s d e t e r m i n e d f r o m K a n c h a n a l a i 's p l a s t ic - z o n e
a n a l y se s . 4 T h e L R F D e q u a t i o n s a r e e v a l u a t e d b a s e d o n t h e e f f e c t iv e
l e n g t h a n d m o m e n t a m p l i fi c a t io n f a c to r s d i s c u s se d i n S e c t i o n s 4 . 2 a n d 4 . 3 .
T h e c o m p a r i s o n s a r e s h o w n f o r s e v e r a l v a l u e s o f L / r , G a n d o r . T h e
d i f f e r e n c e s i n p r e d i c t e d c o l u m n s t r e n g t h d u e t o t h e u s e o f t h e d i f f e r e n t
e f f e c t i v e l e n g t h a n d a m p f i f ic a t i o n f a c t o r s a r e n o t v e r y s i g n i f ic a n t f o r t h e s e
s i m p l e fr a m e s a n d o c c u r m a i n l y i n fr a m e s w i t h h i g h a v a l u e s ( w h i c h a r ee q u i v a l e n t t o f r a m e s w i t h a l a r g e n u m b e r o f l e a n e r c o l u m n s ) . T h e
c o m p a r i s o n s a ls o i n d ic a t e th a t t h e L R F D e q u a t i o n s a r e g en e r a l ly c o n -
s e r v a t iv e f o r a ll c o m b i n a t i o n s o f a a n d G . I f K a n c h a n a l a i ' s c u r v e s a r e
a d j u s t e d t o a c c o u n t f o r i m p e r f e c t i o n s a c c o r d i n g t o t h e p r o c e d u r e d i s -
c u s s e d i n S e c t io n 2 . 2 , t h e L R F D e q u a t i o n s p r o v i d e a n e x c e l l e n t f i t f o r t h e
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 32/40
300 J. Y. Richard L iew, D. W. White, W. F. Chen
P
t.O
0.8
0.6
H $a P Ib
G A = ( | c / L c ) / { I b / 2 L b ) = 4 .0
G B = oo
L / f = 4 0
. . .. S t r o n g a x i s
(Kanchana{ai ,1977)m W e a k a x is
~ - ~ L R F D e l a s t i c K ( E q n s . 1 - 2 , 1 0 - 1 1 )
0 . 4 . . . . L R F D e l a s t i c K ( E q n s . 1 - 2 , 1 7 - 1 8 )
I l i I I0 . 0 0 . 2 0 . 4 0 . 6 0 . 8 1 . 0
H L c / M p
18, Com parison of the AIS C-L RF D beam-colum n equations with the ultimates t r e n g th c u r v e s4 f o r l e a n e d - c o l u m n f r a m e with GA = 4 and L/r = 40.
s t r o n g - a x i s c a s e s s h o w n . T h e y a r e s t i l l s o m e w h a t c o n s e r v a t i v e f o r t h ec o r r e s p o n d i n g w e a k - a x i s c a s e s.
T h e u s e o f L e M e s s u r ie r ' s K fa c to r e q u a t i o n ( ¢ q n ( 1 0 )) a n d t h e m o m e n t
a m p l if ic a t io n f a c to r s ( e q n ( 1 1 ) ) i n c o n j u n c t i o n w i t h t h e L R F D e q u a t i o n s
g e n e r a l l y g i v e s a g o o d e s t i m a t e o f t h e b e a m - c o l u m n s t r e n g t h ( a t l e a s t f o r
t h e s e o n e - s t o r y e x a m p l e s ) . T h e m o d i f i e d K f a c t o r ( e q n ( 1 7 ) ) a n d t h e
c o r r e s p o n d i n g m o m e n t a m p l i f i c a t i o n f a c t o r ( ¢ q n ( 1 8 ) ) g i v e a l m o s t i d e n t i -
c a l r e s u l t s t o L e M e s s u r i e r ' s p r o c e d u r e s a n d t h e y a r e s i m p l e r t o u s e .
6 D O W E R E A L L Y N E E D K F A C T O R S ?
I t i s l ik e l y t h a t s o m e r e s e m b l a n c e o f a K f a c t o r i s n e c e s s a r y i n a n y general
b e a m - c o l u m n d e s i g n e x p r e s s i o n s b a s e d o n a m p l i fi e d f ir s t- o rd e r o r d ir e c tl y
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 33/40
Beam--column design in steel rameworks 301
determined second-order elastic forces. That is, the K factor is probably
necessary to obtain an accurate fit to results from refined analyses of
simple structural systems for a l l possible combinations of axial force and
end moment. The effective length concept is one method of estimating theinteraction of individual member strength with the overall system
strength. The general validity of the AISC-LRFD approach for columns in
a regular building frame has been demonstrated in the preceding section
by comparisons with the 'exact' strength of columns in simple frames.
However, procedures for determination of the proper effective length
factor for building systems such as exterior tubes with interior leaner
columns, systems with significant interaction between moment-resisting
frames and braced or shear-wall cores; eccentrically braced frames; and
flexibly connected frames can be difficult and the results can be ofquestionable accuracy. Although the engineer can usually make con-
servative assumptions to estimate a K factor for member design, the
process of calculating the K factors for each individual member in a
complex framework can be cumbersome and time consuming. Moreover,
the K factor concept is simply an engineering approximation. When used
to account for the stability of a complex structural system, the simple
concepts upon which K factors are based are not fully rational.
6 . 1 S e c o n d - o r d e r e l a s ti c a n a l y s i s a n d b e a m - c o l u m n d es ig r, c o m p a r i s o n
o f t h e L R F D a n d C a n a d i a n S ta n d a r d s
The current LRFD specification permits the engineer to compute the load
effects directly from second-order elastic analysis. Second-order elastic
analysis is the preferred method in the Canadian Standard. 2 However,
most second-order elastic analysis methods provide only the second-order
moments at the element ends. The maximum moments within themembers (including P - 8 effects) usually require additional calcula-
tions. 8'15 The LRFD specification is silent on how analysis calculations
should be made. It is implicitly assumed that this calculation can be
performed as part of a direct second-order elastic analysis. In Ref. 15, the
authors propose the use of an analytical expression for calculation of the
P - 8 moment amplification effects with a direct second-order elastic
analysis. Interested readers are referred to this reference for details.
The use of direct second-order elastic analysis eliminates the need for K
factors in the determination of Mu. However, the use of a K factor is still
required in the axial resistance term of the LRFD equations for accurate
prediction of the beam-column capacity (see Figs 5 and 6).
The interact ion equations given in the Canadian Standard z effectively
use K = 1-0 for calculation of the axial resistance. The differences in the
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 34/40
302 J . Y . R icha rd L iew , D. W . Whi t e , W. F . Chen
H [bA
1.0
0 . 8 L b
G A = ( I c / L c ) / ( I b / 2 L b ) = 4 .0
G B =0 O
L / r = 2 0
S t r o n g a x i s }
W e a k a x i s ( K a n c h a n a l a i , 1 9 7 7 )
L R F D ( L e M e s s u r i e r K - f a c t o r s )
L RFD (K =1 .0 )
P B a > f . 4 ~ ~ = 0 . 0 ~
~ X ~Py 0 .6 f x ~ ~ - . _ _
B 21 .4 ~ , " ~
x ~" ~ L e M e s s u r i e r K - f a c t o r s0.4 3 .0 %
B 2 > 1.4 ~ x = ~ . = . ~ ~ % % . x~ Q = 3 .0 K = 6 .3 0 2
P = 0 . 14 4 Py - x ~
B 2 < 1 . 4 ~ ~ ~ " ~
012 a =.4 0.6 018 1.0
H L c / M p
F i g . 1 9 . C o m p a r is o n o f th e A I S C - L R F D b c ar a-c o lu m n e q ua tio n s w i th a n d w i th o u t t h e us e
o f K f a c t o r s .
a p p r o a c h e s t a k e n b y t h e t w o s p e c i f i c a t i o n s c a n b e s t b e u n d e r s t o o d b y
w r i t i n g b o t h i n t h e s a m e f o r m a t . P o s i n g t h e C a n a d i a n S t a n d a r d p r o c e -d u r e s i n L R F D f o r m a t , t h e m a x i m u m s e c o n d - o r d e r e l a s t i c m o m e n t i s
c a l c u l a te d e s s e n t i a ll y a s B 1 M f in l i e u o f a m o r e d e t a i le d a n a l y si s, w h e r e M f
is t h e m a x i m u m s e c o n d -o r d e r e la s ti c e n d m o m e n t , a n d B1 is a P - 6
m o m e n t a m p l i fi c a t io n f a c to r i n w h i c h K i s t a k e n a s 1 .0 . T h e u s e o f K = 1 .0
i n t h e B 1 te r m i s a n a t t e m p t t o t r e a t t h e b e a m - c o l u m n s a s i s o la t e d m e m b e r s
w i t h t h e c o m p u t e d s e c o n d - o r d e r f o r c e s b e i n g a p p l ie d a t b o t h e n d s . 15 T h e
C a n a d i a n S t a n d a r d a ls o r e q u i re s t h a t t h e e l a st ic P - A a m p l i fi c a ti o n ,
c a l cu l a te d b a s e d o n a n e q u a t i o n e q u i v a l e n t to e q n ( H 1 - 5 ) o f t h e L R F D ,d o e s n o t e x c e e d 1 .4 ( i . e . , B 2 < 1 . 4 ) . I f B 2 i s g r e a t e r t h a n 1 . 4 , s e c o n d - o r d e r
p l a s t ic - z o n e a n a l y s is is g e n e r a l l y r e c o m m e n d e d .
I t c a n b e d e d u c e d f r o m e q n ( 1 2 ) t h a t t h e c o n s tr a i n t o f B 2 < 1 - 4 i n d i r e c t l y
l im i ts t h e m a g n i t u d e o f th e a x i a l l o a d w h i c h m a y a c t o n t h e c o l u m n s . T h i s
r e s tr i c ts t h e u s e o f t h e in t e r a c t i o n e q u a t i o n s t o a r a n g e in w h i c h t h e u s e o f
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 35/40
Bea m-co lumn design in s tee l f ramew orks 3 0 3
P I P
1 . 0 L G A - 0
t G e = ~I .. R - 4 0
0 . 8 " : :p P/Py 0.768
" \ S t r o n g a x i s
0 . 6 " " . ..
0.4 __ ~ 2 . 0 1P/Py 0.356
° I 1 ' . . . .
0 ' 0 0 . 0 0 . 2 0 . 4 0 . 6 0 . 8 1 . 0
H L c / 2 M p
F ig . 20 . C o m p a r i s o n o f t h e A I S C - L R F D b e a m - c o l u m n e q u a t io n s w i th a n d w i t h o u t th e
inc lus ion of a hor izo nta l load 0 .005 (2P) .
K = 1 -0 i n t h e P n t e r m i s r e a s o n a b l e . T h e c o n c e p t is i l l u s t ra t e d w i t h t h e
L R F D b e a m - c o l u m n e q u a t io n s f o r a l e a n e d c o l u m n f r a m e i n F ig . 1 9, a n d
f o r a s im p l e u n b r a c e d p o r t a l f r a m e w i t h r ig i d c o n n e c t i o n s i n F i g . 20 . I n
t h e s e fi g u re s , t h e L R F D i n t e r a c t i o n e q u a t i o n s a r e p l o t t e d u s i n g K = 1 a s
w e l l a s w i t h K f ac t or s d e t e r m i n e d b a s e d o n L e M e s s u r i e r ' s m e t h o d . T h e
u n a d j u s t e d u l t im a t e s t r en g t h c u r v e s g i v en b y K a n c h a n a l a i 4 a r e a l s o
p l o t t e d f o r c o m p a r i s o n . I t c a n b e s e e n t h a t t h e u s e o f t h e c u r v e s b a s e d o n
K = 1 is a d e q u a t e , c o m p a r e d t o t h e ' e x a c t ' s t re n g t h f o r a f r a m e w i t hi n i ti a l ly p e r f e c t g e o m e t r y , a s l o n g a s t h e B 2 f a c t o r i s l e ss t h a n a b o u t 1 .4 .
H o w e v e r , if c o m p a r e d t o th e K a n c h a n a l a i d a t a a f t er a d j u s t m e n t f o r
i m p e r f e c t i o n e f fe c t s, th e c u r v e s b a s e d o n K = 1 w i ll a l w a y s b e s o m e w h a t
u n c o n s e r v a t i v e .
F o r g r a v i t y l o a d c a s e s , t h e C a n a d i a n S t a n d a r d a l s o r e q u i r e s t h a t t h e
s e c o n d - o r d e r e n d m o m e n t s i n th e m e m b e r s b e t a k e n a s n o t le ss t h a n t h e
m o m e n t s p r o d u c e d b y l a te r a l lo a d s o f 0.0 0 5 t i m e s t h e f a c t o r e d g r a v it y lo a d
a p p l i e d a t e a c h s t o r y . F o r t h e f r a m e s h o w n i n F i g. 2 0 , i f t h is p r o c e d u r e isa p p l i e d w i t h t h e L R F D b e a m - c o l u m n e q u a t i o n s a n d a W 8 x 3 1 s e c t io n is
c o n s i d e r e d , a n a x ia l l o a d c a p a c i t y o f PIPy = 0 .7 6 8 is o b t a i n e d . P a r t o f t h e
b e a m - c o l u m n c a p a c i t y i s u s e d u p b y t h e m o m e n t a s s o c i a t e d w i t h t h e
a d d i t i o n a l l a t e r a l l o a d o f 0 .0 0 5Y ~ P . W h e n K = 1 .0 w i t h a g e n e r a l
i n t e r a c t i o n e q u a t i o n , t h e a d d i t i o n a l l o a d o f 0-0 05 t i m e s t h e g r a v i t y l o a d s
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 36/40
304 J. Y. Richard Liew, D. W. White, W. F. Chen
m i g h t b e a p p l i e d w i t h t h e l a t e r a l l o a d i n o r d e r t o a c h i e v e a n o v e r a l l
i m p r o v e m e n t i n t h e p r e d i c t i o n o f t h e u l t i m a t e s t r e n g t h . T h a t i s , t h e
m o m e n t t e r m M , m a y b e a d j u s t e d t o b e t te r f it t h e ' e x a ct ' d a t a in l i eu o f
a d j u s t m e n t o f P , . T h e e f fe c t o f u s i n g a n a d d i t i o n a l l a te r a l lo a d o f 0 -0 05 E P
a n d K = 1 .0 i n t h e L R F D i n t e r a c t i o n e q u a t i o n is i l lu s t r a t e d in F i g . 2 0 .
H o w e v e r , t h is t y p e o f a p p r o a c h is s ti ll n o t l i k e ly t o r e s u l t i n a n i n t e r a c t i o n
e q u a t i o n t h a t i s a s a c c u r a t e f o r a ll ra n g e s o f ax ia l f o r c e v e rs u s m o m e n t a s
e q u a t i o n s w h i c h i n c l u d e a n e f f e ct iv e l e n g t h f a c to r .
T h e f u n d a m e n t a l d i ff e re n c e b e t w e e n t h e A I S C - L R F D a n d C a n a d i a n
S p e c i f i c a ti o n s is t h a t t h e f o r m e r r e q u i r e s t h e u s e o f a K f a c t o r i n t h e a x i a l
r e s i s t a n c e t e r m f o r a l l c a s e s , a n d t h e r e a r e n o r e s t r i c t i o n s o n t h e r a t i o o f
a x i a l f o r c e v e r s u s m o m e n t i n t h e d e s i g n . I t i s a g e n e r a l p r o c e d u r e . T h e
l a tt e r l im i ts th e m a x i m u m v a lu e o f th e s e c o n d - o r d e r m o m e n t a m p l if ic a t i o n
i n a f r a m e , a n d t h u s i n d i r e c t l y r e s t r i c t s t h e l e v e l o f a x i a l l o a d s i n t h e
c o l u m n s s u ch t h a t t h e b e a m - c o l u m n e q u a t i o n s a r e v a l id w i t h o u t t h e u s e o f
a n e f f e c t i v e l e n g t h f a c t o r ( i. e . , K = 1 ). N e v e r t h e l e s s , n e i t h e r o f t h e a b o v e
t w o m e t h o d s a c c o u n t s f o r s y s te m s ta b il it y e ff e c ts i n a c o m p l e t e l y r a t i o n a l
w a y .
7 P R A C T I C A L S E C O N D - O R D E R I N E L A S T I C A N A L Y S I S
I n r e c e n t y ea r s , m a n y e f fo r ts h a v e b e e n d e v o t e d t o t h e d e v e l o p m e n t a n d
v a l i d a t i o n o f s i m p l i f i e d s e c o n d - o r d e r i n e l a s t i c a n a l y s i s . T h e c u r r e n t
p r a c t i c e i n t h e U n i t e d S t a t e s i s t o p e r f o r m e l a s t i c a n a l y s i s ( f i r s t - o r d e r
e l a s t i c a n a l y s i s w i t h m o m e n t a m p l i f i c a t i o n f a c t o r s B 1 a n d B E , o r d i r e c t
s e c o n d - o r d e r e l a s t i c a n a l y s i s ) t o o b t a i n t h e r e q u i r e d s t r e n g t h , M , , f o r
m e m b e r d e s ig n . M a t e r ia l n o n l i n e a r i ty a n d m e m b e r i n it i al i m p e r f e c t io n s
a r e a c c o u n t e d f o r im p l i c it ly in t h e d e s i g n i n t e r a c t io n e q u a t i o n s . I t is w e l lk n o w n t h a t a s t h e f r a m e d e f o r m s i n t o t h e i n e la s ti c r a n g e , t h e d i s t r ib u t i o n
o f m o m e n t s a n d a x ia l fo r ce s in t h e m e m b e r s w i ll d i ff e r f r o m t h o s e o b t a i n e d
b y a s s u m i n g t h e f r a m e r e m a i n s f ul ly el as ti c. C o n v e r s e l y , i f a g i v e n s et o f
f o r c e s a r e c o n s i d e r e d o n a n i s o l a t e d m e m b e r , c o m p a t i b i li t y is n o t s a ti sf ie d
b e t w e e n t h e a c t u al in e la s ti c m e m b e r , a s a s su m e d i n th e d e s i g n e q u a t io n s ,
a n d t h e e l a st ic m e m b e r , a s a s s u m e d i n t h e f r a m e a n a l y si s. T h u s , i t c a n b e
s t a t e d t h a t t h e o n l y w a y t o a c c o u n t f o r s y s t e m s t a b i li ty i n a f u l ly r a t i o n a l
w a y is t h r o u g h a s e c o n d - o r d e r i n e la s ti c f r a m e a n a ly s is .A n ' e x a c t ' a n a l y s i s w h i c h i n c l u d e s t h e s p r e a d o f p l a s t i c i t y , r e s i d u a l
s t r e s s e s , i n i t i a l g e o m e t r i c i m p e r f e c t i o n s , a n d a n y o t h e r s i g n i f i c a n t b e -
h a v i o r a l e f f ec t s, w o u l d n a t u r a l l y e l i m i n a t e t h e n e e d f o r c h e c k i n g t h e
b e a m - c o l u m n i n t e r a c t i o n e q u a t i o n s . T h i s t y p e o f a n a ly s is is a l l o w e d in t h e
n e w A u s t r a l i a n l i m i t s t a t e s s p e c i f ic a t i o n f o r s t e e l d e s i g n 13 a s w e l l a s i n
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 37/40
Beam-column design in steel frameworks 305
Eu r o co d e No . 3 .1 6 H o w ev e r , ' ex ac t ' an a l y s i s i s u su a l ly to o co m p u t a -
t i o n a l ly i n ten s i v e f o r g en e r a l d es i g n u se .
A p o s s i b le a l t e r n a t i v e ap p r o ach i s t o em p l o y a s eco n d - o r d e r p l a s ti c -
h i n g e an a l y s is . Th i s m e t h o d m a k es u se o f co n c en t r a t ed p l a s ti c h i n g es t oap p r o x i m a t e t h e i n e l a st ic b eh a v i o r o f s t ru c t u r a l m em b er s i n a f r am e . Th i s
t y p e o f an a l y s i s u su a l l y i n v o lv es t h e u se o f o n e b eam - co l u m n e l em en t f o r
e a c h f r a m e m e m b e r a n d h a s b e e n s h o w n t o b e e f f ic ie n t f o r a n a ly z i n g
m o d e r a t e l y l a r g e t h r ee - d i m en s i o n a l u n b r ac ed f r am es . 17 Ho w ev e r , a
s i m p l e p la s t ic - h in g e an a l y s i s wh i ch u ses o n e b eam - co l u m n e l em en t f o r
e a c h fr a m e m e m b e r i s o n l y a n a p p r o x im a t e m e t h o d . W h e n u s e d t o a n a ly z e
a s in g l e b eam - co l u m n , t h is m e t h o d d o es n o t n eces sa r i ly p r ed i c t t h e co r r ec t
m e m b e r s t re n g t h e v e n i f m u l t ip l e e l e m e n t s a r e u s e d f o r e a c h m e m b e r .
Th i s b e i n g so , a g en e r a l i n e l a s ti c an a l y s is o f a s t r u c t u ra l sy s t em b ased o n a
s i m p l e p la s t ic h in g e m o d e l c an n o t n ece s sa r il y r ep r esen t t h e co r r ec t
i n e l a s ti c p e r f o r m an ce . So m e f o r m o f a d es i g n ch eck i s s ti ll n eces sa r y t o
acco u n t f o r t h e v a r i o u s p o s s i b le m em b er s t ab il it y e f fec ts . A l t e r n a t i v e l y ,
so m e d es i g n g u i d e l i n es m i g h t b e p r o v i d ed t o d e fi n e an ap p r o p r i a t e t y p e o f
p las t i c h ing e a na lys i s and the rang e o f app l i cab i l i ty o f th i s ana lys i s wh ich
d o es n o t r eq u i r e a b eam - co l u m n i n t e r ac t i o n ch eck . Th i s co u l d b e
acco m p l i sh ed b y co m p ar i n g p l a s ti c -h i n g e so lu t io n s w i th r e f in ed s eco n d -
o r d e r p l a s ti c -z o n e b e n c h m a r k s o f sy s te m a n d m e m b e r r e sp o n s e .I n l i g h t o f th e n ee d t o p r o v i d e m o r e co m p r eh en s i v e g u i d e l in es f o r t h e
u se o f d i r ec t s eco n d - o r d e r i n e l a s ti c an a ly s i s i n t h e co n t ex t o f d es i g n
p r o v i s i o n s , t wo g r o u p s h av e r ecen t l y b een e s t ab l i sh ed : t h e Am er i can
I n s t i t u t e o f S t e e l C o n s t r u c t i o n ( A I S C ) T e c h n i c a l C o m m i t t e e 1 1 7 -
I n e l a s t i c An a l y s i s an d Des i g n , an d t h e S t r u c t u r a l S t ab i l i t y R esea r ch
C o u n c i l ( S S R C ) T a s k G r o u p 2 9 S e c o n d - o r d e r I n el a s ti c A n a l y s i s f o r
F r am e Des i g n . So m e o f t h e m a i n o b j ec t i v es f o r t h ese g r o u p s a r e :
1. To p r o v i d e a u n i f o r m d e f i n it io n o f t e r m s wh i ch p e r t a i n t o n o n l i n ea r
b eh av i o r an d an a l y s i s .
2 . To ca r e f u l ly ca t eg o r i ze an d q u an t i f y b eh av i o r a l e ff ec ts an d p h y s i ca l
p a r a m e t e r s wh i ch a f f ec t i n e l a s ti c f r am e s t r en g t h a n d s t ab i l it y , e . g . ,
t h e m ag n i t u d e an d d i s t ri b u t io n o f r e s id u a l s tr e s se s, m e m b er o u t -o f -
s t r a ig h t n es s , s t o r y o u t - o f -p l u m b n e ss , e t c.
3 . To i d en t i f y b en ch m ar k p r o b l em s f o r u se i n v e r if ica t io n an d co m -
p a r i so n o f s eco n d - o r d e r i n e la s t ic an a l y s i s p r o ced u r es .
4 . To i d en t i f y s i tu a t i o n s in wh i ch ad v an c ed an a l y s i s is ap p r o p r i a t e an ds h o u l d b e p e r f o rm e d .
5 . To a s ses s th e accu r acy an d f eas i b i li ty o f v a r io u s ap p r o a ch es f o r
ine l as t i c ana lys i s .
6 . To i d en t i f y i n n o v a t i v e an a l y s i s an d d e s i g n ap p r o ach e s wh i ch i n-
co rpo ra t e exp l i c it con s idera t ion o f i ne l as t ic e f fec t s i n the ana lys i s .
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 38/40
306 J. Y. Richard Liew, D. W. White, W. F. Chen
An important goal of further research should be to identify circumst-
ances and situations in which simplifying assumptions with regard to
structural behavior can be applied without incurring noticeable errors. In
recent work by King e t a l . , 18 an inelastic analysis approach based on a
modified plastic-hinge concept has been developed for rigid and semi-rigid
frames. This method assumes that the tangent stiffness of a beam-column
element reduces gradually from the elastic stiffness prior to initial yielding
at the element ends, to the stiffness associated with a real hinge, when the
plastic moment (modified to account for axial force effects) is reached at a
hinge location. The proposed analysis can predict the behavior of isolated
beam-column members, as well as the behavior of many types of frames,
more accurately than conventional plastic hinge methods. However, if
member P - 6 effects are large, more than one element per member is stillrequired to obtain accurate solutions. Research on a number of inelastic
analysis and design procedures is currently being undertaken by theauthors. 19
8 CONCLUSIONS
The first part of the paper provides a state-of-the-art review on thedevelopment of the LRFD beam-column interaction equations. The goal
of this part is to highlight the particular difficulties associated with
development of general equations for design of beam-columns in frames.
The LRFD equations in general provide a good fit to the more exact
strength curves for members in simple portal frames and leaned column
frames. This is true only when the column effective lengths are evaluated
properly. To this end, various methods of computing the effective length
factors and the corresponding second-order elastic moment amplificationfactors have been discussed. LeMessurier's procedure, which is based on
the story buckling concept, and the procedure based on a system buckling
analysis are possibly the most general for calculating effective length
factors. The modified K factor procedure gives essentially identical resultsto LeMessurier's procedure, and it is simpler to use. However, the
alignment chart procedure, which is based on the buckling of an idealized
subassemblage, is limited in its applicability and validity. The use of the
alignment chart effective length factors for leaned column frames or for
simple portal frames with unequal column stiffness parameters can result
in an unconservative estimate of member and/or system capacity.
Inelastic reduction of effective length factors by the procedure adopted
in the AISC-LRFD Manual appears to have little consequence on the
beam-column capacity in many types of frameworks, particularly where
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 39/40
Beam--column design in steel rameworks 307
t h e b ea m - co l u m n s a r e n o t su b j ec t ed t o h e av y ax ia l l o ad s. A l so , t h e u se o f
t h e i n e l a st ic K f ac to r s m ay b e q u es t i o n ab l e f o r ca ses i n wh i ch t h e b e am s
m a y b e i n e l a s ti c p r i o r t o th e f ac t o r ed l o ad s b e i n g r each ed . Fo r ex am p l e ,
t h e u se o f i n e l a s t i c K f ac t o r s wo u l d b e a m a t t e r o f co n ce r n i n a p l a s t i c
an a l y s is / d es ig n p r o ced u r e wh i ch t ak e s ad v an t ag e o f in e l a s ti c r ed i st r ib u -
t ion o f fo rces .
T h e C a n a d i a n a p p r o a c h t o b e a m - c o l u m n d e s ig n (w h i c h a v o id s t h e u s e
of K fac to r s ) i s sa fe , bu t t he des ign o f t he m em bers i s impl i c i t ly r es t r i c t ed
t o ce r t a i n r a t i o s o f b en d i n g m o m en t v e r su s ax i a l f o r ce . A l t h o u g h t h e
L R F D i n t e r a c t i o n e q u a t i o n s a r e g e n e r a l f o r t h e f u l l r a n g e o f b e n d i n g
m o m en t v e r su s ax i a l f o r ce , t h ey i n v o l v e t h e u se o f e f fec t iv e l en g t h f ac to r s .
Th e i n t e r p r e t a t i o n o f t h e e f f ec t i v e l en g t h fac t o r s f o r b eam - co l u m n s i n a
c o m p l e x f ra m e w o r k i s a c u m b e r s o m e t a sk . M o r e o v e r , t h e c u r r e n t d e s ig np r o c e d u r e s c o m m o n l y u s e d i n e n g i n e e r in g p ra c ti ce l e a d t o a f u n d a m e n t a l
i n co m p a t i b i li t y b e t w een e l a s ti c f r am e an a l y s i s an d ap p r o x i m a t e i n e l a st ic
m em b e r d es i g n eq u a t i o n s . Th e o n l y f u ll y r a t i o n a l wa y to acco u n t f o r
o v e r a l l f r am e s t ab i li ty is th r o u g h a s eco n d - o r d e r i n e l a s ti c an a ly s i s.
O n e m a j o r ad v a n t ag e o f s eco n d - o r d e r i n e l a s ti c an a l y s is i s t h a t t h e
r ed i s t r i b u t io n o f fo r ces fr o m o v e r l o ad ed m em b er s i s h an d l ed d i r ec t ly . Fo r
a la r g e s tr u c t u r a l sy s t em , o t h e r m e m b er s i n t h e f r am e w o r k m ay e f fec t iv e l y
' b r a c e ' a n o v e r l o a d e d m e m b e r s u c h t h a t t h e m e m b e r a n d t h e o v e r a l ls t r u c t u r e can s t il l r em a i n s t ab l e . Th e r e f o r e , i n g en e r a l t h e b eam - co l u m n
i n t e r ac t i o n eq u a t i o n s ap p ea r t o b e co n se r v a t i v e i n p r o v i d i n g f o r t h e
s t ab i li t y o f l a rg e a n d s t r u c tu r a l sy s tem s . T h e r e f o r e , i t is ex p ec t ed t h a t
f u t u r e r e f i n em en t s i n f r am e an a l y s i s an d d es i g n w il l l i k e ly f o cu s m o r e o n
t h e o v e r a l l sy s t em r e sp o n se an d l e ss o n i n d i v i d u a l m em b er r e sp o n se . Th e
A I S C - L R F D a n d C a n a d i a n S t a n d a r d s p ec if ic a ti on s e x p li ci tl y a ll ow t h e
u se o f d i r ec t s eco n d - o r d e r e l a s ti c an a ly s i s f o r d es ig n . Th e A u s t r a l i an L i m i t
S t a t e s S t ee l Des i g n Sp ec i f ica t io n 13 ( AS4 1 0 0) an d t h e Eu r o co d e No .316
p r o v i d e m o r e ex p l ic i t g u i d an ce f o r u se o f s eco n d - o r d e r i n e la s t ic an a l y s is i n
d e s i g n . A l t h o u g h m u c h p r o g r e s s h a s b e e n m a d e i n r e c e n t y e a r s o n
seco n d - o r d e r i n e l a s ti c an a l y s i s f o r f r am e d es i g n , m u ch m o r e w o r k r em a i n s
t o b e d o n e .
A C K N O W L E D G E M E N T S
T h e s u p p o r t o f th i s r e s e a r c h b y th e N a t i o n a l S ci en c e F o u n d a t i o n u n d e r
g r an t n u m b e r M SM-8 91 44 61 i s g r a t e f u l ly ack n o w l ed g ed . Th e f i rs t au t h o ris o n a n o v e r s e a s g r a d u a t e s c h o l a rs h i p fr o m t h e N a t i o n a l U n i v e r s i t y o !
S i n g a p o r e . T h e f in a n c ia l s u p p o r t p r o v i d e d b y t h e N a t i o n a l U n i v e r s i t y o !
S i n g ap o r e is a lso g r a t e f u l ly ack n o w l ed g ed .
7/30/2019 Beam Column Chen JCSR 1991
http://slidepdf.com/reader/full/beam-column-chen-jcsr-1991 40/40
308 J. Y. Richa rd Liew, D. W. W hite, W. F. Ch en
R E F E R E N C E S
1 . AISC, M anu al o f S t ee l Const ruc tion , L oa d a nd Res i s tance Factor Des ign , 1stedn , A ISC Ch icago , I ll ino i s, Sep temb er 1986.
2 . Canadian Standards Assoc ia t ion , L imi t s ta tes des ign of s tee l s t ruc tures ,C A N / C S A - S l6 . 1- M 8 9 , D e c e m b e r 1 98 9.
3 . Yura , J . A. , E lements for t eaching load and res i s tance fac tor des ign:Co m bined bend ing and ax ia l l oad , Un ive r s i ty o f Texas a t A us t in , Texas , June1988, pp . 55-71.
4 . Kan chana la i , T . , T he des ign and behav io r o f beam-co lum ns in unbrace d s tee lf r ames , AI SI P ro j ec t No . 189 , Rep or t N o . 2 , C iv il Eng inee r ing /S t ruc tu re sR esea rch L ab. , Un ivers i ty of Texas a t A us t in , Texas , 1977, 300 pp .
5 . LeM essu r i e r, W . J ., Pe r sona l comm unica t ion , 1984.
6 . Johnson , B . G . , SS R C Gu ide to S tabi li ty D es ign Criteria fo r Meta l S t ruc tures ,3rd edn , Jo hn W i ley & Sons , New Y ork , 1976, 616 pp .7 . Ch en , W . F . & Lu i , E . M . , StrUctura l S tab i l i t yhTh eor y a nd Imp lemen ta t ion ,
Elsevier Sc ience Publ i shers , New Y ork , 1986, 490 pp .8 . W hi te , D. W . & Ha j ja r , J . F . , A ppl ica t ion of seco nd-o rder e las tic ana lys i s in
L R F D : R e s e a r c h to p r a ct ic e , Proc . 1990 Nat ional S tee l Conference , A I S C ,Ch icago, M arch 1990, pp . 11 .1-22 .
9 . Ju l i an , O . G . & La wren ce , L . S . , No te s on Ju li an and Law rence nom ographsfo r de t e rm ina t ion o f e ff ec ti ve l eng th , Unpub l i shed Re por t , 1943.
10 . LeMessur ie r , W. J . , A prac t ica l method of second order ana lys i s , Par t
2 - - R i g i d f r a m e s. E n g n g J . A I S C , 14(2) (1977) 49 -67.11. Y ura , J . A . , The e f fec t ive l eng th o f co lumns in unbraced f r ames . E n g n g J .A I S C , 8(2) (1971) 37--42.
12. G oto , Y . , Suzuki , S. & C h e n , W . F . , Bow ing ef fec t on e last ic s tab il ity off ra m e s u n d e r p r i m a r y b e n d i n g m o m e n t s . J . St ruc t . Eng . ASCE, 117(1) (1991)111-27.
13. S tandards A us t ra l ia , AS4100-1990, S tee l S t ruc tures , Sydney , Au s t ra l ia ,1990.
14. Br idg e , R. Q . , In-p lane buckl ing and i ts in fluence on f ram e des ign , Proc .Four t h In t. Co l l oqu i um SS RC , N ew Y ork C i ty , Ap r i l 1989, pp . 185-96 .
15. L i ew, J . Y . R icha rd , W hi t e , D . W . & C he n , W . F . , Beam -co lumn des ign ins tee l f i 'amew orks , S t ruc tura l En ginee r ing R ep or t , CE-STR-90-24 , Pu rdu eUn ivers i ty , Sep tem ber 1990, 68 pp .
16. Eu roco de No . 3 , Des ign o f s t ee l s t ruc tu res : Pa r t 1 - -G ene ra l ru l e s and ru l e sfor bui ld ings , Vol . 1 , Ed i ted draf t , Is sue 3 , EC 3-8 8-C l l -D 5, Com m iss ion ofthe Euro pea n C om mu ni t ie s , Apr i l 1990.
17. Z i em ian , R . , W hi t e , D . W . , De ie r l e in , G . G . & McG ui re , W . , On e approachto ine last ic ana lys is and des ign , Proc. 19 90 N at ion al Steel Conference, A IS C ,Ch icago, M arch 1990, 19 .1-19 .
18. K ing , W. S . , W hi t e , D . W . & C he n , W . F . , A mod i f i ed p l as ti c h inge m e thod
for second-order ine las t ic ana lys i s of s tee l semi- r ig id f rames , S t ruc tura lEng inee r ing Rep or t , CE-STR-90-19, Pu rd ue Un ive r s i ty , 19 90 , 34 pp .Journ a l o f S t ruc tura l Eng i neer ing , A SC E, 117 (1991) ( to appear ) .
19. W hi t e , D . W . , L i ew, J . Y . R icha rd &C h en , W . F . , Secon d-o rde r i nel as ti cana lys i s fo r f r ame des ign : A r epor t t o SSRC Task Group 29 on r ecen t