basic network configuration for file
DESCRIPTION
Basic Network Configuration for File. Upon completion of this module, you should be able to: Configure Data Mover network devices Implement DNS and Time Services. Basic Network Configuration for File. Lesson 1: Data Mover Network Devices. - PowerPoint PPT PresentationTRANSCRIPT
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
Upon completion of this module, you should be able to:• Configure Data Mover network devices• Implement DNS and Time Services
Basic Network Configuration for File 1
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
Lesson 1: Data Mover Network Devices
Basic Network Configuration for File 2
During this lesson the following topics are covered:• Network device speed and duplex settings• IP interface for client access• Routing table
Copyright © 2014 EMC Corporation. All Rights Reserved.
Modifying and Displaying Configuration
Settings > Network > Settings For File
Basic Network Configuration for File 3
Copyright © 2014 EMC Corporation. All Rights Reserved.
Listing Network Devices
Settings > Network > Settings for File > Devices
Basic Network Configuration for File 4
Copyright © 2014 EMC Corporation. All Rights Reserved.
Duplex & Transmission Speed
• Duplex setting Preferred setting is auto (Default) Best practice setting is auto for GigE connections
• Transmission Speed Defaults to auto Use maximum speed supported on the network between the VNX
and the client
Basic Network Configuration for File 5
Copyright © 2014 EMC Corporation. All Rights Reserved.
Setting Speed/Duplex
Device Properties to set Speed/Duplex
Basic Network Configuration for File 6
Copyright © 2014 EMC Corporation. All Rights Reserved.
IP Address Configuration
• Interfaces tab > Create• Required Parameters
IP Address Subnet mask Broadcast address
Basic Network Configuration for File 7
Copyright © 2014 EMC Corporation. All Rights Reserved.
Displaying IP Configuration
Settings > Network > Settings For File > Interfaces
Basic Network Configuration for File 8
Copyright © 2014 EMC Corporation. All Rights Reserved.
Interface IDSubne
tNetwork
IPv6 Support
• VNX supports IPv6 IP addresses• More addresses• Better security
Roll security into the protocol
• IPv6 address example:
2620:0000:0170:0062:021B:D5FF:FE25:7082
Basic Network Configuration for File 9
Copyright © 2014 EMC Corporation. All Rights Reserved.
Unisphere: Control Station IPv6
System > Control Station Properties
Basic Network Configuration for File 10
Copyright © 2014 EMC Corporation. All Rights Reserved.
Data Mover Routing
• Routing table of a Data Mover directs outgoing network traffic via, both external and internal gateways Routes to a host Routes to a network
• Data Mover routing table can contain 3 types of routes Directly connected Static Dynamic
• Packet Reflect Reply to network client requests Route and ARP tables are not examined
No need to determine the route to send the reply packets
Basic Network Configuration for File 11
Multiple Interfaceson a Network
When more than one IP interface are on the same network, the first interface configured will be the default path out of the Data Mover.Example: Interface “A” iscreated on a Data Mover, then interface “B”. All resource queries (e.g. DNS) will go out through interface “A”.
Copyright © 2014 EMC Corporation. All Rights Reserved.
Viewing Data Mover Routing Information
Settings > Network > Settings For File > Routes
Basic Network Configuration for File 12
Default Gateway:0.0.0.0
Route to Network:
192.168.64.0
Copyright © 2014 EMC Corporation. All Rights Reserved.
Configure Default Gateway
Basic Network Configuration for File 13
Copyright © 2014 EMC Corporation. All Rights Reserved.
Deleting Routes
Basic Network Configuration for File 14
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
During this lesson the following topics were covered:• Network device speed and duplex settings• IP interface for client access• Routing table
Lesson 1: Summary
Basic Network Configuration for File 15
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
Lesson 2: Implement DNS and Time Services
Basic Network Configuration for File 16
During this lesson the following topics are covered:• Data Mover DNS Configuration• Time Services (NTP and SNTP)• Implement Time Services for a Data Mover
Copyright © 2014 EMC Corporation. All Rights Reserved.
Displaying DNS Settings
Basic Network Configuration for File 17
Settings > Network > Settings For File > DNS
Copyright © 2014 EMC Corporation. All Rights Reserved.
Configuring a Data Mover for DNS
Basic Network Configuration for File 18
Copyright © 2014 EMC Corporation. All Rights Reserved.
Time Services Overview
Basic Network Configuration for File 19
• Data Mover NTP client Synchronization of the system clock with an NTP or SNTP server
• NTP Sophisticated algorithms for time correction and maintenance to
allow time synchronization with an accuracy of about a millisecond
• SNTP Subset of NTP for use in environments with less stringent
synchronization and accuracy requirements
• To the client, NTP or SNTP are indistinguishable
Copyright © 2014 EMC Corporation. All Rights Reserved.
Initializing Time Services on a Data Mover
Basic Network Configuration for File 20
System > Hardware > Data Movers
Copyright © 2014 EMC Corporation. All Rights Reserved.
Basic Network Configuration for File
During this lesson the following topics were covered:• Data Mover DNS Configuration• Time Services (NTP and SNTP)• Implement Time Services for a Data Mover
Lesson 2: Summary
Basic Network Configuration for File 21
Copyright © 2014 EMC Corporation. All Rights Reserved. Basic Network Configuration for File 22
Module Summary
Key points covered in this module:• Recommended Data Mover speed/duplex setting is 'auto'• Use Data Mover time services to synchronize with Windows
and Unix/Linux environments