basic cli commands for overture isg 5100 - cisco...
TRANSCRIPT
Basic CLI commands for Overture ISG 5100
Written by CiscoNETThursday, 24 September 2009 16:55 - Last Updated Friday, 25 September 2009 15:32
These days, I am more involving WAN Ethernet service product which is a bit complicated to
troubleshoot. Simply, tons of vendors and gears in the market. If you are not dealing with thosedevices all the time, you would spend time to play with some commands until you get outputwhat you want. WAN Ethernet service is very popular in data communication market incompatible price. By comparing to traditional circuit, it is a lot cheaper. Also, H/W cost ischeaper. It dramatically drops your maintenance cost. For those reasons, WAN Ethernet servicewill get more sunshine in the market.
By the way, there are many vendors out there. Seems like major players are Tellabs, Fujitsu,Cisco, Nortel, Ciena Corporation, Overture networks, Anda networks and etc.
Here is the basic commands for overture ISG5100 Ethernet Switch for carriers.
- To see uptime
Overture_ISG5100# uptime 10:40pm up 42 days, 3:03, load average: 0.00, 0.00, 0.00
1 / 9
Basic CLI commands for Overture ISG 5100
Written by CiscoNETThursday, 24 September 2009 16:55 - Last Updated Friday, 25 September 2009 15:32
- To see all VLAN
Overture_ISG5100# port show all vlan Amt Port Type Pvid Pri Only IngF Vlan/Label Cir Burst Flow Pause ------------------------------------------------------------------------------- 2.1 Enet 0 1 off off none N/A N/A N/A N/A 2.2 Enet 0 1 off off none N/A N/A N/A N/A 2.3 Enet 0 1 off off none N/A N/A N/A N/A 2.4 Enet 0 1 off off none N/A N/A N/A N/A 2.5 Enet 0 1 off off none N/A N/A N/A N/A 2.6 Enet 0 1 off off none N/A N/A N/A N/A 2.7 Enet 0 1 off off none N/A N/A N/A N/A 2.8 Enet 0 1 off off none N/A N/A N/A N/A 3.1 OC3 0 1 off off mgmt 1 2 N/A N/A
- To show L2 class interface
Overture_ISG5100# l2classify show Egress Rate Limt RuleName Pri Port VLAN DSCP Pbit Port Q Action Cir/Burst PBit DSCP ------------------------------------------------------------------------------- OVR111 1 1.1 any any any 3.1 4 PU/ 14 100/ 100 no no OVR311 1 3.1 15-15 any any 1.1 4 PO/ n/a no/ 0 no no
- To check a status of port
Overture_ISG5100# port show 1.1 status
2 / 9
Basic CLI commands for Overture ISG 5100
Written by CiscoNETThursday, 24 September 2009 16:55 - Last Updated Friday, 25 September 2009 15:32
Showing Port status Port Type Admin Oper Duplex Speed AutoNeg Lpbk RxErrTotal ------------------------------------------------------------------------------ 1.1 Enet up up Full 100M n/a disab 0000000000
- To see port configuration
Overture_ISG5100# port show 1.1 config Admt Dot InFwd Spd Full Auto Port Type Admin Learn Polc Jmbo Only 1p Mode 100M Dup Neg Xovr ------------------------------------------------------------------------------- 1.1 Enet up off off on off off sw/br on on off mdi Overture_ISG5100#
- To check VLAN setup
Overture_ISG5100# port show 1.1 vlan Amt Port Type Pvid Pri Only IngF Vlan/Label Cir Burst Flow Pause ------------------------------------------------------------------------------- 1.1 Enet 0 1 off off none N/A N/A N/A N/A
- To check details of the port
Overture_ISG5100# port show 1.1 detail
3 / 9
Basic CLI commands for Overture ISG 5100
Written by CiscoNETThursday, 24 September 2009 16:55 - Last Updated Friday, 25 September 2009 15:32
Showing port details Port Type Drops Rx Tx Q Disc Bundle ------------------------------------------------------------------------------- 1.1 Enet 0000000000 3611113990 0624990186 0000001727 N/A
- To check detail counters
Overture_ISG5100# port show 1.1 detail counters
Showing port detailed counters -- Counters for 1.1 ------------------------------------------- TX_BYTES_GOOD 0663834660 RX_BYTES_GOOD 4136184967 TX_BYTES_TOTAL 0663834660 RX_BYTES_TOTAL 4136184402 TX_UNICAST_PKTS 0624988463 RX_SHORT_PKTS_GOOD 0000000000 TX_MULTICAST_PKTS 0000000000 RX_SHORT_PKTS_BAD 0000000000 TX_BROADCAST_PKTS 0000000006 RX_LONG_PKTS_GOOD 0000000000 TX_PAUSE_PKTS 0000000000 RX_LONG_PKTS_BAD 0000000000 TX_VLAN_PKTS 0000000000 RX_UNICAST_PKTS 3611210914 TX_CRC_ERRS 0000000000 RX_MULTICAST_PKTS 0000023969 TX_DEFERS 0000000000 RX_BROADCAST_PKTS 0000000000 TX_EXCESS_DEFERS 0000000000 RX_PAUSE_PKTS 0000000000 TX_SINGLE_COLS 0000000000 RX_VLAN_PKTS 0000000000 TX_MULTI_COLS 0000000000 RX_CRC_ERRS 0000000000 TX_EXCESS_COLS 0000000000 RX_ALIGN_ERRS 0000000000 TX_LATE_COLS 0000000000 RX_RUNTS 0000000000 TX_NORM_COLS 0000000000 RX_LENGTH_ERRS 0000000000 TX_FIFO_ERRS 0000000000 RX_FALSE_CRS 0000000000 TX_PKTS_64 0347003901 RX_PHY_ERRS 0000000000 TX_PKTS_127 0132025544 RX_FIFO_ERRS 0000000000 TX_PKTS_255 0031918287 RX_IGNORED 0000000000 TX_PKTS_511 0023211372 RX_OPCODE_BAD 0000000000 TX_PKTS_1023 0045002001 RX_PKTS_64 0316078920 TX_PKTS_1518 0045827364 RX_PKTS_127 0267271711 RX_PKTS_255 0224172537 RX_PKTS_511 0125399747 RX_PKTS_1023 0169824803 RX_PKTS_1518 2508487175
4 / 9
Basic CLI commands for Overture ISG 5100
Written by CiscoNETThursday, 24 September 2009 16:55 - Last Updated Friday, 25 September 2009 15:32
- To clear PM counters
Overture_ISG5100# port clear 1.1 pm-counters
- To see PM result, only apply serial link not Ethernet.
Overture_ISG5100# port show 3.1 pm Showing PM Counters Port Type Section ES SES SEFS CV ------------------------------------------------------------------------------ 3.1 OC3 0 0 0 0 Port Type Line ES SES CV UAS ------------------------------------------------------------------------------ 3.1 OC3 0 0 0 0 Port Type FarendLine FEES FESES FESCV FEUAS ------------------------------------------------------------------------------ 3.1 OC3 0 0 0 0 Port Type Path ES SES CV UAS ------------------------------------------------------------------------------ 3.1 OC3 0 0 0 0 Port Type FarendPath FEES FESES FECV FEUAS ------------------------------------------------------------------------------ 3.1 OC3 0 0 0 0 Overture_ISG5100#
- To see queues
Overture_ISG5100# port show all detail queues
5 / 9
Basic CLI commands for Overture ISG 5100
Written by CiscoNETThursday, 24 September 2009 16:55 - Last Updated Friday, 25 September 2009 15:32
Port Type Cntr Queue0 Queue1 Queue2 Queue3 Queue4 Queue5 Queue6 ------------------------------------------------------------------------------- 1.1 GigSFP Bytes 000000 000000 000000 000000 000000 000000 000000 Pkts 000000 000000 000000 000000 000000 000000 000000 3.1 OC3 Bytes 000000 000000 000000 000000 000000 000000 000000 Pkts 000000 000000 000000 000000 000000 000000 000000
- To see errors on the interface
Overture_ISG5100# port show 1.1 errors Showing Port Errors Port Type RxCrc RxAlign RxRunt RxLength RxCrs RxPhy RxFifo ------------------------------------------------------------------------------ 1.1 Enet 00000000 00000000 00000000 00000000 00000000 00000000 00000000
- To see live traffic on the link, default interval is 5 sec
Overture_ISG5100# port show 1.1 util Per Second Utilization for Port(s) 1.1 Count=0 DisplayTime=5 Secs Port Type TxPkts RxPkts TxBits RxBits Tx % Rx % ------------------------------------------------------------------------------- 1.1 Enet 0 2166 0.000000Kbps 20.364153Mbps 0.000 20.36 Port Type TxPkts RxPkts TxBits RxBits Tx % Rx % ------------------------------------------------------------------------------- 1.1 Enet 1 1538 0.672000Kbps 13.783864Mbps 0.000 13.78
- To see log for alrams
6 / 9
Basic CLI commands for Overture ISG 5100
Written by CiscoNETThursday, 24 September 2009 16:55 - Last Updated Friday, 25 September 2009 15:32
Overture_ISG5100# log show alarm Aug 13 19:31:53 isg5000 isgservices: FAULT TIME="Thu Aug 13 19:31:53 2009 "SEVERITY="Major" SLOT="Slot 3" DEVICE="port 1"ID="Section Loss of Frame (LOF)" SEQUENCE NUMBER="1" Aug 13 19:31:54 isg5000 isgservices: FAULT TIME="Thu Aug 13 19:31:54 2009 "SEVERITY="Cleared" SLOT="Slot 3" DEVICE="port 1"ID="Section Loss of Frame (LOF)" SEQUENCE NUMBER="2" Aug 13 19:33:12 isg5000 isgservices: FAULT TIME="Thu Aug 13 19:33:12 2009 "SEVERITY="Critical" SLOT="Slot 1" DEVICE="port 1"ID="Link failure" SEQUENCE NUMBER="3" Aug 13 19:34:36 isg5000 isgservices: FAULT TIME="Thu Aug 13 19:34:36 2009 "SEVERITY="Cleared" SLOT="Slot 1" DEVICE="port 1"ID="Link failure" SEQUENCE NUMBER="4" Aug 13 19:34:49 isg5000 isgservices: FAULT TIME="Thu Aug 13 19:34:49 2009 "SEVERITY="Critical" SLOT="Slot 1" DEVICE="port 1"ID="Link failure" SEQUENCE NUMBER="5" Aug 13 19:45:37 isg5000 isgservices: FAULT TIME="Thu Aug 13 19:45:37 2009 "SEVERITY="Cleared" SLOT="Slot 1" DEVICE="port 1"ID="Link failure" SEQUENCE NUMBER="6" Aug 13 19:46:37 isg5000 isgservices: FAULT TIME="Thu Aug 13 19:46:37 2009 "SEVERITY="Critical" SLOT="Slot 1" DEVICE="port 1"ID="Link failure" SEQUENCE NUMBER="7"
- To see log for command history
Overture_ISG5100# log show command Sep 1 12:48:10 isg5000 cli_sh: CLI USER="AshburnCMC"IP_ADDR="153.39.198.229" CMD="port show all vlan" Sep 1 12:52:40 isg5000 cli_sh: CLI USER="AshburnCMC"IP_ADDR="153.39.198.229" CMD="port show 1.1 status" Sep 1 12:52:56 isg5000 cli_sh: CLI USER="AshburnCMC"IP_ADDR="153.39.198.229" CMD="port show 1.1 detail" Sep 1 12:52:58 isg5000 cli_sh: CLI USER="AshburnCMC"IP_ADDR="153.39.198.229" CMD="port show 1.1 detail" Sep 1 12:53:16 isg5000 cli_sh: CLI USER="AshburnCMC"IP_ADDR="153.39.198.229" CMD="port show 1.1 detail counters" Sep 1 12:54:12 isg5000 cli_sh: CLI USER="AshburnCMC"
7 / 9
Basic CLI commands for Overture ISG 5100
Written by CiscoNETThursday, 24 September 2009 16:55 - Last Updated Friday, 25 September 2009 15:32
IP_ADDR="153.39.198.229" CMD="port show 1.1 detail counters" Sep 1 12:54:13 isg5000 cli_sh: CLI USER="AshburnCMC"IP_ADDR="153.39.198.172" CMD="port show 1.1 status" Sep 1 12:54:18 isg5000 cli_sh: CLI USER="AshburnCMC"IP_ADDR="153.39.198.172" CMD="port show 1.1 status" Sep 1 12:54:40 isg5000 cli_sh: CLI USER="AshburnCMC"IP_ADDR="153.39.198.172" CMD="port show 1.1 counters " Sep 1 12:54:52 isg5000 cli_sh: CLI USER="AshburnCMC"IP_ADDR="153.39.198.172" CMD="port show 1.1 detail" Sep 1 12:54:57 isg5000 cli_sh: CLI USER="AshburnCMC"IP_ADDR="153.39.198.229" CMD="port show 1.1 detail counters" Sep 1 12:55:09 isg5000 cli_sh: CLI USER="AshburnCMC"IP_ADDR="153.39.198.172" CMD="port show 1.1 status" :
:
- To see all config
Overture_ISG5100# show status
- To see start configuration
Overture_ISG5100# config show
8 / 9
Basic CLI commands for Overture ISG 5100
Written by CiscoNETThursday, 24 September 2009 16:55 - Last Updated Friday, 25 September 2009 15:32
9 / 9