SHENZHEN BASECAMP PROGRAM Machine &Tool List

Oscilloscope (Tektronix Digital Storage TDS2024C)

200 MHz Bandwidth

4-channel

2 GS/s Sample Rate on All Channels

2.5k point Record Length on All Channels

Advanced Triggers including Pulse Width and Line-selectable Video

16 Automated Measurements, and FFT Analysis

Built-in Waveform Limit Testing

Automated, Extended Data Logging Feature

Autoset and Signal Auto-ranging

Oscilloscope (Tektronix Digital Phosphor TDS3054C)

500 MHz Bandwidth Model

4-Channel Model

Sample Rates up to 1.25 GS/s Real-time on All Channels

10k Standard Record Length on All Channels

3,600 wfms/s Continuous Waveform Capture Rate

Suite of Advanced Triggers

6.5 digit resolution

Basic V dc accuracy of up to 0.0024 %

Dual display

100 μA to 10 A current range, with up to 100 pA resolution

Wide ohms range from 10 Ω to 1 GΩ with up to 10 μΩ resolution

2 x 4 ohms 4-wire measurement technique

Both models measure frequency and period

Measures capacitance and temperature

USB memory drive port

Fluke 45 and Agilent 34401A emulation

Graphical display

Trend Plot paperless recorder mode, statistics, histogram

Digital Multimeter (Fluke 8846A)

Oscilloscope (Tektronix Digital Phosphor DPO7354)

4 Channel

2.5 GHz Bandwidth

Max Sample Rate: 10 GS/s (3 to 4 Channels), 20 GS/s (2 Channels), 40 GS/s (1 Channel)

>250,000 wfms/s Maximum Waveform Capture Rate

Pinpoint(TM) Triggering Provides the Most Flexible and Highest Performance Triggering, with 1400 Other Combinations to Address Virtually Any Triggering Situation

Laboratory DC Power Supply (GW INSTEK 3303)

4 Independent Isolated Output

Four "3 Digits" LED Displays

0.01% Load and Line Regulation

Low Ripple and Noise

Tracking Operation and Auto Series/Parallel Operation

Output ON/OFF Switch

Output Voltage and Current Setting When Output Disable

Fan Speed Control Circuit to Minimize Fan Noise

Overload and Reverse Polarity Protection

LCR Meter (Tonghui TH2816B)

Basic accuracy : 0.05%

Equivalents circuit : series, parallel

Measurement speed : fast - 32 ms/meas, med - 90ms/meas, slow - 650 ms/meas

Calibration function : open, short and load

Measurement terminal : 5-terminal

Display model direct, dABS, d%, V/I monitor,bin number and bin counter

Display : 240 x 64 dot-matrix LCD display, 6-digit resolution

Signal frequency over 10,000 frequencies from 50Hz - 200Hz

Thermal Meter (Fluke 54-IIB)

Relative time clock on MIN, MAX, and AVG provides a time reference for major events

Electronic Offset function allows compensation of thermocouple errors to maximize overall accuracy

Measures J, K, T, and E-types of thermocouples

Readout in ºC, ºF, or Kelvin (K)

Additional thermocouple types R, S, and N (for a total of 7 different types)

Recall function allows logged data to be easily reviewed on the meter display

Dual Mobile Comm DC Source (c)Output ratings:

Voltage: 0 to 15 V

Current: 0 to 3 A

Peak Current for up to 7 ms: 5 A

Programming accuracy at 25°C ±5°C (% of setting plus fixed):

Voltage: 0.05% + 10 mV

+Current: 0.05% + 1.33 mA

DC readback accuracy:

Voltage: 0.03% + 5 mV

Current (-3 A to + 5 A): 0.2% + 0.5 mA

Current (-1 A to + 1 A): 0.1% + 0.2mA

Current (-20 mA to + 20 mA): 0.1% + 2.5 µA

DC Electronic Loads (Chroma 6314A)

RS232 Standard

Max Power: 200W, 100Wx2(Dual),30W & 250W, 300W, 350W, 600W, 1200W

Wide range 0~600V operating voltage

Up to eight channels in one mainframe, for testing multiple output SMPS

Parallel load modules up to 1400W for high current and power applications

Synchronization with multiple loads

Flexible CC, CR, CP and CV operation modes

Dynamic loading with speeds up to 20 kHz

Fast response of 0.32mA/μs ~ 10A/μs slew rate

Paperless Recorder (Yokogawa MV2000)

Multi-channel universal inputs

MV2000: up to 48 input channels Secure, high capacity memory

Internal memory: 200 MB Choice of Compact Flash and USB removable storage media Removable input terminals simplify field wiring

Lightweight aluminum construction (MV2000)

Advanced network connectivity with Email, file transfer, and web server functions.

Paperless Recorder (Yokogawa GP20)

Structure: portable

Monitor 12.1 inch TFT color LCD (pixels: 600 x 800)

Touch screen:4 wire resistance type touch screen, 2 point touch detection

Maximum number of connections10

Flash Memory:500 MB (Media: Flash)

External memory

SD memory card (max 32GB

Operational channel number:100

Communication channel number:300

Rated supply voltage:100 ~ 240 VAC

ENA Series Network Analyzer (Keysight E5080A)

9 kHz to 4.5/6.5/9 GHz, 2- or 4- port, 50 ohm

Wide dynamic range 152 dB (typical)

Fast measurement speed 3 ms (401 points)

Low trace noise 0.0005 dB rms (typical)

High temperature stability 0.005 dB/°C

Wide source power range –90 to +15 dBm (spec)

Intuitive touch-based GUI on large, high-resolution 12.1" screen

E5071C/8753 code compatibility

EXA Signal Analyzer (Keysight N9010A)

Balance your challenges: Address diverse needs with a single tool -the fast, flexible EXA

Get the most cost-effective analysis for millimeter-wave measurements

Measure the smallest signals in the presence of large ones with best-in-class level accuracy, DANL & TOI

Perform power measurements quickly at discrete frequency points with list-sweep mode

Simplify testing with X-Series measurement apps: phase noise, noise figure, analog demodulation, wireless communications & more

Wireless Connectivity Tester (R&S CMW500)

Multi-technology (LTE, WCDMA, GSM and CDMA2000 ) protocol tester with a layer 1 to layer 3 stack implementation

Future-proof, powerful RF hardware that supports all 3GPP defined bandwidths up to 6 GHz and technology beyond LTE Rel-10

Data rates up to 150 Mbps in the downlink and 50Mbps in the uplink

MIMO 2 x 2 and MIMO 4 x 2

Multicell and inter-RAT capability

Development environment for layer 1 to layer 3 signaling scenarios with automatic configuration of the layers below

TTCN libraries and software tools for developing signaling conformance test cases

Groundbreaking graphical test script tool (R&S CMW cards) for easy creation of application tests

Revolutionary protocol test tool chain to speed up error analysis and root cause finding

UHF TEM Cell (TESCOM TC-5060B)

Radiation and susceptibility test

Broadband TEM Cell up to 3 GHz

Small size, Small footprint for desktop application

High effective shielding

Specifically designed for all types of mobile phones

DB25 Data Connector, SMA RF Connector

Paste Printer (Torch T1100)

PLC control system.

Panasonic gear motor.

The imported linear guide track keeps smooth and exact printing.

Working Pressure : 4~6 KGF/ square centimeter

The max printing area : 300*400mm

Printing speed: about 60 pieces per hour

Printing accuracy : 0.4mm

SMT Pick and Place Machine (Autotronik BS281)

Flying Vision for components from 0.6 mm x 0.3 mm (0201) to 16mm x 14mm

Bottom Vision Camera for alignment of 01005, up to 0.5 fine pitch QFP &

BGAs (option)

32 lane feeder bases mount at left and right of system for maximum capacity of 64 automatic 8 mm Tape Feeders

Optional feeders and accessories allow a wide variety of configurations for full and partial reels of Tape, strips of Cut Tape, Stick / Tube, and IC Tray Packaging

Programming via CAD Conversion, Direct Input, or Teaching/Fiducial Recognition Camera

PC controller, monitor, and keyboard included

Optional Dispensing system

Benchtop Reflow Oven (Autotronik BT301)

PCB pallet size: 350 x mm 240 mm

Effective fusion welding range: 250 x mm 200 mm

Heating element type: infrared quartz heater + forced hot air reflow

Heating capacity range: ambient temperature – 310

Preheat time: about 2 minutes

Control computer unit: equipped with dual core CPU Tablet PC

The display panel unit: 7 inch high resolution touch screen LCD

Temperature control settings: Based on the rapid temperature rise curve of intelligent programming (degree / sec)

Temperature features: automatic painting real-time temperature characteristic curve

Near Field Probe (RF2+PA303N)

LANGER EMV-Technik for famous German near field probe (near field probe) manufacturing company. modern electronic products was designed more and more refined, they design with 2mm in diameter near field probe (near field probe), and with High sensitivity and high identification rate, it provides a good tool for modifying the product (debug)

Microscope PCB-500V

PCB-500V computer circuit board detection microscope system is the traditional optical microscope and computer through the photoelectric conversion organic unifies in together, not only can make microscopic observation in the eyepiece, but also in observation of real-time dynamic image on the screen of the computer (digital camera) and the need for photo editing, save and print

objective lens zoom range 0.8X-5X

The microscope can zoom in a row, the ratio of is 6.5:1

Double pupil distance adjustment range: 55-75mm

mobile working distance: 95mm

total magnification: 8 - 50X

Anechoic Chamber (8-4-4)

Frequency range: 30MHz ~ 18GHz;

Absorption reflection material loss: 30MHz ~ 18GHz = 15dB;

Shielding performance of shielding room

Microwave: 1GHz ~ 10GHz = 100 dB; 18 GHz = 10 GHz ~ 90dB;

Test method of anechoic chamber according to the general standards of GB 12190-90;

the normalized site attenuation : + 4dB, field uniformity : 0 ~ 6dB, in accordance with the GJB2926-97 standard.

Autotronik SP600

Steel mesh frame size: 350 350mm x to x 736 500mm

Printing range: Max x 400mm 600mm

PCB size: Max x 410mm 650mm

X axis and Y axis adjustable size: 13 + / - mm

Adjustable printing angle: + / - 3,5

Back part height: 25 mm

Z axis size: 0 - 35mm

Repeat accuracy: 0.01 + / - mm

Screen printing machine volume: 1006 mm x 851mm x1064mm (Wx L x H)

3D Printer (Objet Connex 260)

Coating thickness (Z axis): only 16 microns thick coating

Modeling resolution: X axis: 600 Y DPI axis: 600 Z DPI axis: 1600 DPI

Print mode:

Digital materials (DM):30 micron (0.001 inch)

High quality (HQ):16 micron (0.0006 inch)

High speed (HS):30 micron (0.001 inch)

Typical accuracy: 50 mm below the graphics can be achieved 20-85 microns

Full size model can reach 200 microns

Supporting materials: objet ABS class digital materials RGD5160-DM Objet VeroClear rigid transparent material Objet Tango series of flexible rubber material Objet Full Cure 20 conventional use of transparent material Objet Vero series of rigid opaque materials Objet Durus White polypropylene material

3D Printer (Projet 3500)Printing mode:HD HD /HS - high speed/UHD - Ultra – clear/ XHD - extreme HD

Construction size: 298 x 185 x 203 mm

resolving power

HD mode:375 x 375 x 790 DPI (XYZ); 32 μ

HS mode:375 x 375 x 790 DPI (XYZ); 32 μ

UHD mode:750 x 750 x 890 DPI (XYZ); 29 μ

XHD mode:750 x 750 x 1600 DPI (XYZ); 16 μ

Accuracy (typical)

Component size is 0.001-0.002 inches per inch (0.025-0.05 mm).

Modeling material

VisiJet X

VisiJet Crystal

VisiJet Proplast

VisiJet Navy

VisiJet Techplast

VisiJet Procast

Constant Temperature and Humidity Chamber (ESL-10KA)Inner container size: mm H1000 * mm D1000 * mm W1000

Test environment: the environment temperature of +25, the relative humidity is less than 85%

Temperature range: -70℃ 150℃

Temperature fluctuation: ≤0.50℃

Temperature deviation: ±2.0℃

Heating time: -70℃→+150℃ ≤60 min

The cooling time: +20℃→-70℃ ≤80 min

Relative humidity deviation:

+ 3.0%RH (> humidity >75%RH

+ 5.0%RH; (humidity ≤ 75%RH)

Cold Cycle Test Machine (TSG 5055WS)

Inner box size: W970mm × H780mm × D670mm

Test environmental conditions: Ambient temperature +25℃, relative humidity is less than or equal to 85%, circulating cooling water temperature is less than or equal to 30 DEG C (ice), circulating cooling water pressure 0.32 ~ 0.45MPa

Preheat temperature range (high temperature): +60℃ +200℃

Heating up time: +60℃→+200℃ ≤20min

Pre cooling temperature range (low temperature): -78℃ 0℃

Cooling time: +20℃ → -75℃≤75 min

Temperature impact range: +60 +150 ℃/

-55 -10 ℃

Temperature recovery time: ≤5 min

Salt Spray Tester (MY-8100B) Laboratory temperature: 35℃±1℃/50℃±1℃

pressure barrel temperature: 47℃±1℃/63℃±1℃

brine temperature: 35℃±1℃/50℃±1℃

temperature fluctuation degree: ≤±0.5℃

temperature uniformity: ≤±1℃

temperature deviation: ≤±1℃

spray volume: m1/80cm2/h 1.0 2.0

relative humidity:over 85%

air pressure: 1.00±0.01kgf/cm2

pH value PH: 6.5 7.2 3.0 3.3

laboratory capacity: 1000L

salt water bucket capacity: 20L

Hot Filament Tester (CRS-GWT)Hot wire Ø 4mm±0.04mm NiCr(80/20)

Thermocouple Ø0.5mmK

Electric heating hot wire temperature 500℃ 1100℃

Test article on hot wire test pressure: 1.0N + 0.1N

Maximum ironing depth: 7mm + 0.5mm;

Test product movement speed: 10mm/s ~ 25 mm/s;

Test time: 30s + 0.1s

The test volume ≥0.5m3

Background illumination ≤20Lx

Outline dimension W1100mm * D600mm * H1220mm,

Vent hole Ø100mm;

Power 220V 50-60Hz 1kVA

Needle Flame Tester (CRS-NFT)

Needle hole burner: endoporus: Φ 0.5mm ± 0.1mm

External diameter: ≤Φ 0.9mm; length: ≥ 35mm

Burner angle: 45

The burning time: 0-999.9s ± 0.1s

The holding time: 0-999.9s ± 0.1s,

The flame height: 12mm ± 1mm

The application of gas: 95%

Temperature measurement range: 0~1000

Thermocouple: Φ0.5mm

Sand and Dust Tester (MY-SC1000)

Test area size: (W*H mm) (D*) 1000*1000*1000

Sample frame net height adjustment range: 0~750mm

Timing range: 0-99 hours 59 minutes

Timing accuracy: + 1 minutes

Load cycle control: 0-99 hours 59 minutes

Dust cycle control: 1 second ~9999 minutes

Waterproof Testing Machine (MY-IP16-2500)

The inner box size: 1000 x 1000 mm deep wide x 1000mm high

IP12 drip tray: 800X800mm, high 120MM, hole distance: 20X20MM, drip hole: 0.4MM

Drip flow: -1mm 0.5/min + IP2-, 3mm IP1 + 1/min

Water jet flow: 0.07L/Min

Water spray pressure: 80 ~ 150 kPa (adjustable)

Water jet intensity: IP6-100 + 5 (L/min), IP5-12.5 + 0.625 (L/min),

Rev: 1-3 RPM / min

Bearing: 50 kg

Water spray duration: 3,10999 min (adjustable)

CNC Machine (JDVT 600-A12S)X/Y/Z axis motion positioning accuracy: 0.005,0.005,0.005mm

X/Y/Z axis repeated positioning accuracy: 0.0045,0.0045,0.0045mm

X/Y/Z axis working stroke: 600/400/350mm

Table size: 730*400mm

Maximum working load: 300kg

Spindle maximum speed: 24000rpm

Shank size: BT30

Tool magazine capacity: 24

Fast moving speed: 15m/min

Maximum cutting feed rate: 15m/min

Drive system: AC servo

Working voltage: three phase 380V/50Hz

Gas source pressure: 0.52MPa

Machine weight: 4000Kg

Robotic Arm (UR3)

Weight: 11 kg / 24.3 lbs

Payload: 3 kg / 6.6 lbs

Reach: 500 mm / 19.7 in

Joint ranges: +/- 360° Infinite rotation on end joint

Speed: All wrist joints: 360 degrees/sec.

Other joints: 180 degrees/sec.

Tool: Typical 1 m/s. / 39.4 in/s.

Repeatability: +/- 0.1 mm / +/- 0.0039 in (4 mils)

Footprint: Ø118 mm / 4.6 in

Degrees of freedom: 6 rotating joints

Control box size (WxHxD): 475 mm x 423 mm x 268 mm / 18.7 x 16.7 x 10.6 in