barcelona 26-vi-2007dds data analysis1 dds data analysis, ii alberto lobo ice-csic & ieec
TRANSCRIPT
Barcelona 26-vi-2007 DDS Data Analysis 1
DDSDDS Data Analysis, II Data Analysis, II
Alberto Lobo
ICE-CSIC & IEEC
Barcelona 26-vi-2007 DDS Data Analysis 2
Noise reduction philosophy
Problem: to assess the contribution of a given perturbation to the total noise force fint.
Approach: 1) Apply controlled perturbation to the system
2) Measure “feed-through” coefficient between force and perturbation:
int( )f
F
3) Measure actual with suitable sensors
4) Estimate contribution of by linear interpolation:
int ( ) ( )f F
5) Substract out from total detected noise:
red int int ( )f f f
6) Iterate process for all identified perturbations
Barcelona 26-vi-2007 DDS Data Analysis 3
Various diagnostics items
Temperature and temperature gradients:– Sensors: thermometers at suitable locations– Control: heaters at suitable locations
Magnetic fields and magnetic field gradients:– Sensors: magnetometers at suitable locations– Control: induction coils at suitable locations
Charged particle showers (mostly protons):– Sensors: Radiation Monitor– Control: non-existent
Barcelona 26-vi-2007 DDS Data Analysis 4
General scheme for DDS DA(S2-IEC-TN-3031)
For each diagnostic:
1. Measurement runs
i. Controlled disturbance ON (if applicable)
ii. Controlled disturbance OFF
2. Available data (in each case)
3. LTP-wide reference model
4. Data Analysis Procedures
Barcelona 26-vi-2007 DDS Data Analysis 5
Thermal
22 NTC
temperature
sensors
16 heaters
Barcelona 26-vi-2007 DDS Data Analysis 6
Thermal
Barcelona 26-vi-2007 DDS Data Analysis 7
Thermal
Optical Window
Barcelona 26-vi-2007 DDS Data Analysis 8
Thermal
Optical Window
Heaters
Heater
Barcelona 26-vi-2007 DDS Data Analysis 9
Thermal
Optical Bench
Temperature
Sensors
Barcelona 26-vi-2007 DDS Data Analysis 10
Thermal
Suspension
Struts: Heaters
and Sensors
Barcelona 26-vi-2007 DDS Data Analysis 11
The Problem
• COMPLETED WORK:
• Progress towards:
- DDS Heaters sizing (P, SNR, dT …)- OW heaters comparison with experiment- Modelling, analytic or SW tool- Others
– Quantify thermal gradients between any two points, given the DDS sensors measurements.
Barcelona 26-vi-2007 DDS Data Analysis 12
EH heaters: activation scheme
P
t
Heater set 2
Heater set 1
= 1000 secHeaters signal
Sensors response(CGS SW tool)
T1
T4T3
T2
T1
T4T3
T2
H2H1
H2H1
Barcelona 26-vi-2007 DDS Data Analysis 13
Heaters ON: EH
Measurements: Temperatures T1, T2, T3, T4 per IS Accelerations a1, a2 per IS Laser Metrology x1,
Main thermal signal: T (T1T3) (T2T4) per IS
Data Analysis: fit data to
2
radiometer
1
2
pl Ta
m T
23
rad. press.
16
3
la T T
mc
Transfer function temperature-acceleration ensues
Barcelona 26-vi-2007 DDS Data Analysis 14
Heaters ON: OW
Measurements: Temperatures T5, T6 in IS1, T11, T12 in IS2
Laser Metrology x1 for IS1, x2 x1 for IS2
Thermal signals: temperature closest to activated heater
Data Analysis: fit data to ARMA(2,1):
1
1 1
1ˆ ˆ ˆ( ) ( ) ( )1 1
zz T z T z
z z
• Should be OK in MBW –even beyond!–, and for each OW
• Can easily be improved, if necessary, at lower frequencies
Barcelona 26-vi-2007 DDS Data Analysis 15
LCA Thermal Model, v8
S2-CGS-TN-3031
Barcelona 26-vi-2007 DDS Data Analysis 16
2) Apply sinusoidal input, TJ = 1 · sin (0 t)
Proposal: Frequency Sweep
y(n) = h(z) x(n) y(n) = ystd (n) + ytrs (n) = = A exp (in+) H() + ytrs (n)
x(n) = A exp (in ) n>0
• WHAT: Evaluate transfer functions points at a fixed frequency
• HOW: Fitting exponential decay
1) Select input node: node = J
3) Fit results on different node (K) peak values:
yK, max (n) = A exp (- n / T) + C
4) Get transfer function node K wrt node J
GKJ (0) = C
Barcelona 26-vi-2007 DDS Data Analysis 17
Hacking
• FITTING: Simulation results sampled at the input frequency from the maximum in the last period to some selected point after transient. Substract initial value afterwards.
[a,b,c,da,db,dc] = F(y,Tin,node)
1 mHz
5 mHz
50 mHz
Barcelona 26-vi-2007 DDS Data Analysis 18
All heaters OFF
• Temperature measurements to be translated into LTP signals (TM accelerations and/or laser metrology phase shifts) by transfer function scaling. Has ambiguities unless a suitable model of the physical processes is available.
• Cross correlations between different channels:
• Some can be (safely) discarded, e.g. OW-EH, etc.• Others cannot, e.g., among different struts• Global LTP system identification
• Some sensor readings used as housekeeping data, e.g., OB and redundant OW sensors
• Improved experimental characterisation needed and underway
Barcelona 26-vi-2007 DDS Data Analysis 19
Application: OB Sensors Location
Sensors
Input
Sensors
Sensors
Barcelona 26-vi-2007 DDS Data Analysis 20
Magnetic disturbances in the LTP
Magnetic noise is due to various causes:
• Random fluctuations of magnetic field and its gradient• DC values of magnetic field and its gradient• Remnant magnetic moment of TM and its fluctuations• Residual high frequency magnetic fields
Test masses are a AuPt alloy
0.7 Au + 0.3 Pt
of low susceptibility
510
and low remnant magnetic moment:
8 20 10 A mm
a = 46 mmm = 1,96 kg
Barcelona 26-vi-2007 DDS Data Analysis 21
LCA
Barcelona 26-vi-2007 DDS Data Analysis 22
Magnetometer available areas
Barcelona 26-vi-2007 DDS Data Analysis 23
Magnetometers’ accommodation
Barcelona 26-vi-2007 DDS Data Analysis 24
CoilAccommodation
Barcelona 26-vi-2007 DDS Data Analysis 25
Magnetic diagnostics: coils ON
Philosophy: apply controlled periodic magnetic fields:
bg p 0p apap ( , ) ( ); i tt e B B xB xB B
Force comes then a two frequencies:
0 app bg app app bg0
V
F m B B B B B
2 app app0
V
F B B
– B0 is calculated rather than measured with magnetometers
– Bbg is LTP background magnetic field
Barcelona 26-vi-2007 DDS Data Analysis 26
Magnetic diagnostics: coils ON
Data:
• Laser Metrology x1 and x2 x1 for each VE being affected
• a1 (a2) from IS1 (IS2) if possible
• Coil feed intensity and frequency
Analysis: from above data we can obtain
, , , ,2 ,2 ,2, , and , ,x y z x y zF F F F F F
, ,2x xF F and are measured with good SNR (~ 100 max)
, , ,2 ,2, , ,y z y zF F F F are measured with poorer SNR
Barcelona 26-vi-2007 DDS Data Analysis 27
Magnetic diagnostics: coils ON
From Fx,2 we can estimate to ~1%
From Fy,2 and Fz,2 we get error correction and cross check
F can be useful to estimate remnant magnetisation M
This is more complicated, though:
• Fx, has (max) SNR ~ 100, but Fy, and Fz, quite less
• Yet all three components are needed, as M is a vector
• In addition, M needs to be disentangled from Bbg
Barcelona 26-vi-2007 DDS Data Analysis 28
Continuous magnetic field monitor
Data: • 4 3-axis magnetometers at fixed positions in LCA • 12 sampled magnetic field channels
Magnetic field and gradient must be known at TM locations:
i. Magnetometer data streams are fed to suitable extrapolation algorithmsii. These algorithms are (so far) computationally demandingiii. To be run offlineiv. They produce a magnetic field + gradient map around TMsv. Magnetic map error estimates will be delivered by the algorithm, too
• Processed data directly yield magnetic transfer function.• Extrapolation operation errors need tight control.
Barcelona 26-vi-2007 DDS Data Analysis 29
LCA and Magnetic sources
Magnetic sources:
• Around 50 identified
• Distributed outside LCA
• Their positions are known
• They behave mostly as magnetic dipoles
• Dipole moments are unknown
• Solar panel is no such
Barcelona 26-vi-2007 DDS Data Analysis 30
LCA and Magnetic sources
Barcelona 26-vi-2007 DDS Data Analysis 31
Magnetic field map
Barcelona 26-vi-2007 DDS Data Analysis 32
Magnetic field reconstruction
• Exact reconstruction not possible with 4 magnetometers and around 50 dipole sources (+solar panel)
• Tentative approaches attempted so far:
• Linear interpolation• Weighted interpolation –various schemes• Statistical simulation (“equivalent sources”)
• Latest idea: Multipole field structure estimation:
• Fully possible up to quadrupole approximation• Partly up to octupole –and tricky, but not impossible...
Barcelona 26-vi-2007 DDS Data Analysis 33
Multipole reconstruction theory
B x x
In vacuum,
A multipole expansion of B follows that corresponding to (x):
,
, , 1lm lml m
a r Y r x n x n n
The coefficients alm(r) depend on the magnetisation M(x). In anobvious notation, structure is:
)
,
lm
l m
(B x xB
Barcelona 26-vi-2007 DDS Data Analysis 34
Multipole reconstruction theory
Evaluation of multipole terms is based on some assumptions:
1. Magnetisation is due to magnetic dipoles only
2. Such dipoles are outside the LCA.
Somewhat legthy calculations lead to:
with
) 0
4 ll
lm
ml
mM r Y
(B x n
*
31
4
2 1lm
lm l
YM d x
l r
n
M x
Barcelona 26-vi-2007 DDS Data Analysis 35
Multipole reconstruction theory
Idea is now to fit measured field values to a limited multipoleexpansion model. Arithmetic sets such limit to quadrupole:
)
1model
lml
l m l
(B xB xL
Fit criterion is to minimise squared error:
4
2measur
2l
1m eed ods s
slmM
B xB x
2
0lmM
Barcelona 26-vi-2007 DDS Data Analysis 36
Arithmetics of reconstruction algorithm:
Data channels: 12
Mlm dipole: 3
Mlm quadrupole: 5
Mlm octupole: 7
Multipole reconstruction theory
3+5 = 8 < 12 => some redundancy, OKthese 3 are uniform field components
5+7 = 12 exactly!!
Summing up:
• Full quadrupole structure up to quadrupole level –even redundant
• Fully possible up to octupole if constant dipole can be determined
• Errors in the order of 10% (TBC, could be better!)
Barcelona 26-vi-2007 DDS Data Analysis 37
Ideal error map
L %TM1 %TM2
1 32.0 47.8 2 3.1 12.3 3 1.9 0.6
Barcelona 26-vi-2007 DDS Data Analysis 38
Radiation Monitor
From S2-IEC-TN-3031:
...The radiation monitor is primarily designed to help understand and quantify these variable processes [modulations of CGR and fluxes of SEP] by monitoring the external particle fluxes and allowing these to be correlated with the test-mass charge measurements.
Barcelona 26-vi-2007 DDS Data Analysis 39
Radiation Monitor
Barcelona 26-vi-2007 DDS Data Analysis 40
Radiation Monitor
Barcelona 26-vi-2007 DDS Data Analysis 41
Radiation Monitor
Barcelona 26-vi-2007 DDS Data Analysis 42
Radiation Monitor
1. Establish the charging-rate in the TMs due to cosmic-ray interactions. Compare with Monte Carlo simulations. Requires a long run with no UV lamps operating.
2. Establish the cosmic-ray transfer function from the radiation monitor to the test-mass charge.
3. Establish or limit the level of power spectral density of cosmic-ray modulations caused by solar activity. Provided by continuous operation of RM and other monitors available.
4. Establish the solar-energetic particle (SEP) flux enhancement distributions (temporal and fluence) seen by the radiation monitor.
5. Establish the solar-energetic particle transfer function from the radiation monitor to the test-mass charge. Done by cross-correlation of TM charge control data with RM (and other monitors) SEP data.
6. Estimate the solar-energetic particle induced charging rate and compare with simulations.
7. Demonstrate the closed loop charge control process and estimate its gain factor.
Barcelona 26-vi-2007 DDS Data Analysis 43
Radiation Monitor
Radiation Monitor data are formatted in a histogram-like form.A histogram is generated and sent (to OBC) every 614.4 sec.
Barcelona 26-vi-2007 DDS Data Analysis 44
Radiation Monitor
Additional data required:
1. Test mass charges, Q1 and Q2 every 1000-10,000 seconds to an accuracy to 104 elementary charges with sign.
2. ULU time status including lamps on/off and commanded UV levels
3. Inertial sensor noise power spectra
4. RM calibration data – channel to energy conversion
5. RM calibration data – efficiency factors for each spectral channel
6. RM calibration data – spectral resolution as function of energy
7. Updated satellite geometry model
8. Solar activity indicators
Barcelona 26-vi-2007 DDS Data Analysis 45
End of PresentationEnd of Presentation
Barcelona 26-vi-2007 DDS Data Analysis 46
Radiation Monitor
GCRSEP
Barcelona 26-vi-2007 DDS Data Analysis 47
Radiation Monitor
Barcelona 26-vi-2007 DDS Data Analysis 48
Data handling issues:
• Front detector hits sent as flags• Coincident events sent as energy deposed• Electronics is able to cope with up to 5000 c/s,
so data compression will be eventually needed.
Testing issues:
• Artificially generated pulses• Muon test • Proton source exposition: PSI, end of October
Radiation Monitor