Bank locker system

• In today's modern world, security plays an important role.

• Every person has precious accessories like gold, jewelry or cash.

• It is not enough to have these accessories, but security of this is very important, for this purpose we keep them in bank lockers.

• Still we often hear or read in newspaper that some fake person has access the locker of another person and have stolen money.

• In order to overcome this type of frauds, authentication of the person who wants to use the locker is very important.

Introduction

Objectives

Banks offer locker facilities to individuals as and when required Both public as well as private sector banks offer this facility to needy individuals for a small annual fee These lockers are maintained in a secure facility that is under constant surveillance and security There are several advantages of availing a bank locker, a few best ones are listed as follows:• Softy.• Easy access.• Available in any bank branch.• Anyone can avail.• Nomination facility available.

Proposed system

• In this project we propose a Biometric based secure access which can provide a sophisticated theft alert system for bank locker system.

• This system contains microcontroller, keypad, Biometric module and LCD display.

• By using keypad we need to press the button to the three door opening purpose.

• Then using biometric module to open the main door for authorized person.

• This system offers better solution for the bank security system and it will also help us to track the person who tried to open the locker without the permission and proper authentication.

Block diagram

About Microcontroller

• PIC16F877A microcontroller is used for this project• It is 8-bit Microcontroller• System is RISC Architecture• It has Small set of Instruction set• It has 35-Instructions only• Compatibility: avail 28/40 Pin ICs

Microcontroller overview

• Operating Speed Max 20 MHz, Voltage-(2-5.5)v• Memory:

Flash Program 8Kx14 Words,

RAM 368 Bytes,

EEPROM Data Memory 256 Bytes• Low power, High speed Flash/EEPROM Technology

Features of Microcontroller

• It has 5 Ports for Internal and External usage• It has on chip Timers. 3 Timers are avail• It has in built Analog to Digital Converter• In built Multiplexer availability for signal Selection• It has serial as well as Parallel Communication facilities• In built Capture, Compare and Pulse width modulation

Pin Diagram

Characteristics of Biometrics

Any human characteristic can qualify as a biometric characteristic as long as it satisfies the following requirements:-

Universality

Distinctiveness

Permanence

Collectability

Working of Biometrics System

Fingerprint Recognition

A fingerprint is made of a series of ridges and furrows on the surface of the finger. Ridge ending, ridge bifurcation and minutiae points. Algorithm is developed to distinguish whorl, arch and loop.

Fingerprint authentication

GSM Modem

• GSM modem is the Data Communicating Equipment which is connected to terminal equipment for data transmission and reception.

• GSM stands for Global System for Mobile Communication• SIM stands for Subscriber identity Module• GSM modem is controlled using AT commands• AT stands for Attention • Ex- AT, AT+CMGR, AT+CMGS, AT+CMGD etc.

AT Commands & Corresponding Operation

AT Commands DescriptionAT To check if Modem is

connected properlyATE0 To turn echo off

ATE1 To turn echo on

AT+CMGF Set operating Mode

AT Commands & Corresponding Operation

AT Commands DescriptionAT+CMGD= <index>, <delflag>

To delete a message

AT+CMGR= <index> To read message from an index

AT+CMGS= “contact no.” , TP-type address

To send message to specified contact no.

Enable (E)-This line allows access to the display through R/W and RS lines. When this line is low, the LCD is disabled and ignores signals from R/W and RS. When (E) line is high, the LCD checks the state of the two control lines and responds accordingly.Read/Write (R/W)-This line determines the direction of data between the LCD and microcontroller. When it is low, data is written to the LCD. When it is high, data is read from the LCD.Register select (RS)-With the help of this line, the LCD interprets the type of data on data lines. When it is low, an instruction is being written to the LCD. When it is high, a character is being written to the LCD.

16*2 LCD

•A relay is used to isolate one electrical circuit from another.

• It allows a low current control circuit to make or break an electrically isolated high current circuit path.

Relay

19

What’s Inside?

DC motor

20

ADVANTAGES

• Provide high security.• No question arise to hack or crack system.• No need to remember username.• Easy to use.• Fully automatic system• Dual layer security with fingerprint and password option.• Theft protection and alert.

Applications

• In offices• In bank lockers• For used in identification.• In nuclear power plant control room.• All that places when unique identity & high security is required.• Cash caring vehicle

References

1. A. Jain et al: “BIOMETRICS: Personal Identification in Networked Society”, Kluwer Academic Publishers, 1999, ISBN0-7923-8345-1.

2. S. Prabhakar, S. Pankanti, and A. K. Jain, “Biometric Recognition: Security and Privacy Concerns”, IEEE Security and Privacy Magazine, Vol. 1, No. 2, pp. 33-42, 2003.

3. http:// www.biometrics.org/

4. http://www.biometricsconsotorium.com

5. http://www.howstufworks.com

6. http://www.youtube.com/watch?v=FCEyHiLxuC8