ball valve
TRANSCRIPT
1352-SERIES Electrically Operated Ball Valve Technical Specifications
Data Sheet Ref. No : SU-1352-00001
SUDE PUNE / BANGALORE
MODEL NO.: 1352\50\40\BSP\RB\CS\S6\T\PROP\ SD-1000-05\CPT200\POT\2LS\SERVO
Quotation Ref. No Quotation Date
1. ITEM ASSEMBLY OF 2 WAY BALL VALVE FITTED WITH SINGLE PHASE QUARTER TURN ELECTRIC ACTUATOR
2. MAKE SUDE 3 APPLICATION Water Industries 6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE Valve Size 50mm Port Size 40mm End connection BSP Screwed Body Material Carbon Steel Ball Material SS316 Seating material Teflon Flowing medium Non-injurious to Body Ball & Seals
Pressure 10 Bar
Type of construction
Reduce Bore Single piece design, Antistatic fire safe
Ball valve
Temperature Ambient
Characteristic Proportionate
Fitted with
Sdtork Make Single Phase Quarter Turn Electric Actuator Supply Voltage 230 V AC.
ACTUATOR DETAILS 3.1 Model SD-1000-05 3.2 Output motion type Linear 3.3 Output Torque ( Nm ) 50 Nm 3.4 Output speed ( Sec/90 °) 17 sec/90° 3.5 Manual hand wheel PROVIDED 3.6 Travel limit switches
2 Nos Type : 1 NO + 1 NC, change over contact, contact rating: 5 A, 230 V AC
3.7 Torque limit switches Not required, AS 1000-series actuator are provided with stall duty motor
3.8 Local indicator PROVIDED 3.9 Class of Protection IP67 3.10 Weight of the actuator (Kgs.) 9 kgs. 3.11 Duty S2-10 min 3.12 Mounting 3.14 G. A. Drawing Reference No 3.15 Electrical Wiring Diagram Ref, No MOTOR DETAILS 4.1 Type Reversible Single Phase Synchronous Stall Duty Motor 4.2 Supply 230 V +/- 10 %, 50 Hz +/- 5 % AC Supply 4.3 Duty S2-10 min / S-4-30 % 1200 Cycles/ hr.
4.4 Insulation Class F 4.5 Rating ( Watts) 110 Watts OPTIONAL ACCESSORIES 5.1
Feedback Potentiometer
Out put : 100-235 Ohms Provided
5.2
Additional Limit Switches
Qty : 2 nos. Type : 1 NO + 1 NC, Change over contact, Contact rating: 5 A, 230VAC
Provided
5.3
Two Wire Transmitter Type : Two wire, Actuator mounted Supply : 12-36 VDC, Output : 4-20 m A
Provided
5.4
Remote Position indicator
Available in servo controller Digital : 0-100 %
Provided
5.5
Servo controller (Valve positioner) Panel Mounted
Input signal : 4-20 m A, Output : 4-20 m A Feed back : 0-500 Ohms, supply 230 V AC, This will have auto calibration facility.
Provided
5.6 Interface Card Input signal : 4-20 m A, Feed back : 100-235 Ohms,
Provided
5.7 Local Push Button Station
This will consist of Auto /Off / Manual selector switch, Open/Close push buttons.
Provided
6 GENERAL POINTS 6.1 Inspection By Customer at our works
6.2 T. C.& Manuals 2 Sets with unit 6.3 Warranty 18 months from the date of supply or 12 months from the date of installation
which ever is earlier. 6.4 Packing Thermo cool Packing Housed in corrugated Box
SPECIAL NOTE :
1352-SERIES Electrically Operated Ball Valve Technical Specifications
Data Sheet Ref. No : SD-1352-00002
SUDE PUNE / BANGALORE
MODEL NO.: 1352\50\40\BSP\RB\CS\S6\T\ONF\ SD-1000-05\2LS
Quotation Ref. No Quotation Date
1. ITEM ASSEMBLY OF 2 WAY BALL VALVE FITTED WITH SINGLE PHASE QUARTER TURN ELECTRIC ACTUATOR
2. MAKE SUDE 3 APPLICATION Water Industries 6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE Valve Size 50mm Port Size 40mm End connection BSP Screwed Body Material Carbon Steel Ball Material SS316 Seating material Teflon Flowing medium Non-injurious to Body Ball & Seals
Pressure 10 Bar
Type of construction
Reduce Bore Single piece design, Antistatic fire safe
Ball valve
Temperature Ambient
Characteristic On/Off Type
Fitted with
Sdtork Make Single Phase Quarter Turn Electric Actuator Supply Voltage 230 V AC.
ACTUATOR DETAILS 3.1 Model SD-1000-05 3.2 Output motion type Linear 3.3 Output Torque ( Nm ) 50 Nm 3.4 Output speed ( Sec/90 °) 17 sec/90° 3.5 Manual hand wheel PROVIDED 3.6 Travel limit switches
2 Nos Type : 1 NO + 1 NC, change over contact, contact rating: 5 A, 230 V AC
3.7 Torque limit switches Not required, AS 1000-series actuator are provided with stall duty motor
3.8 Local indicator PROVIDED 3.9 Class of Protection IP67 3.10 Weight of the actuator (Kgs.) 9 kgs. 3.11 Duty S2-10 min 3.12 Mounting 3.14 G. A. Drawing Reference No 3.15 Electrical Wiring Diagram Ref, No MOTOR DETAILS 4.1 Type Reversible Single Phase Synchronous Stall Duty Motor 4.2 Supply 230 V +/- 10 %, 50 Hz +/- 5 % AC Supply
4.3 Duty S2-10 min / S-4-30 % 1200 Cycles/ hr. 4.4 Insulation Class F 4.5 Rating ( Watts) 110 Watts OPTIONAL ACCESSORIES 5.1
Feedback Potentiometer
Out put : 100-235 Ohms Not Provided
5.2
Additional Limit Switches
Qty : 2 nos. Type : 1 NO + 1 NC, Change over contact, Contact rating: 5 A, 230VAC
Provided
5.3
Two Wire Transmitter Type : Two wire, Actuator mounted Supply : 12-36 VDC, Output : 4-20 m A
Not Provided
5.4
Remote Position indicator
Available in servo controller Digital : 0-100 %
Not Provided
5.5
Servo controller (Valve positioner) Panel Mounted
Input signal : 4-20 m A, Output : 4-20 m A Feed back : 0-500 Ohms, supply 230 V AC, This will have auto calibration facility.
Not Provided
5.6 Interface Card Actuator Mounted
Input signal : 4-20 m A, Feed back : 100-235 Ohms,
Not Provided
5.7 Local Push Button Station
This will consist of Auto /Off / Manual selector switch, Open/Close push buttons.
Not Provided
6 GENERAL POINTS 6.1 Inspection By Customer at our works
6.2 T. C.& Manuals 2 Sets with unit 6.3 Warranty 18 months from the date of supply or 12 months from the date of installation
which ever is earlier. 6.4 Packing Thermo cool Packing Housed in corrugated Box
SPECIAL NOTE :
1358-SERIES Electrically Operated Plastic Ball Valve Technical Specifications
Data Sheet Ref. No : SU-1358-00001
SUDE PUNE / BANGALORE
MODEL NO.: 1358\50\PVC\PVC\T\PROP\BSP\SD-1000-05\2LS\POT\SERVO\CPT200
Quotation Ref. No Quotation Date
1. ITEM ASSEMBLY OF 2 WAY PLASTIC BALL VALVE FITTED WITH SINGLE PHASE QUARTER TURN ELECTRIC ACTUATOR
2. MAKE SUDE 3 APPLICATION 6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE Valve Size 50mm End connection BSP Screwed Body Material PVC Ball Material PVC Seating material Teflon Flowing medium Acid
Pressure 10 Bar
Temperature Ambient
Characteristic Proportionate
Fitted with
Sdtork Make Single Phase Quarter Turn Electric Actuator Supply Voltage 230 V AC.
ACTUATOR DETAILS 3.1 Model SD-1000-05 3.2 Output motion type Linear 3.3 Output Torque ( Nm ) 50 Nm 3.4 Output speed ( Sec/90 °) 17 sec/90° 3.5 Manual hand wheel PROVIDED 3.6 Travel limit switches
2 Nos Type : 1 NO + 1 NC, change over contact, contact rating: 5 A, 230 V AC
3.7 Torque limit switches Not required, AS 1000-series actuator are provided with stall duty motor
3.8 Local indicator PROVIDED 3.9 Class of Protection IP65 3.10 Weight of the actuator (Kgs.) 9 kgs. 3.11 Duty S2-10 min 3.12 Mounting 3.14 G. A. Drawing Reference No 3.15 Electrical Wiring Diagram Ref, No 3.16 Weight of Actuator – Kgs MOTOR DETAILS 4.1 Type Reversible Single Phase Synchronous Stall Duty Motor 4.2 Supply 230 V +/- 10 %, 50 Hz +/- 5 % AC Supply 4.3 Duty S2-10 min / S-4-30 % 1200 Cycles/ hr. 4.4 Insulation Class F 4.5 Rating ( Watts) 110 Watts OPTIONAL ACCESSORIES
5.1
Feedback Potentiometer
Out put : 100-235 Ohms Provided
5.2
Additional Limit Switches
Qty : 2 nos. Type : 1 NO + 1 NC, Change over contact, Contact rating: 5 A, 230VAC
Provided
5.3
Two Wire Transmitter Type : Two wire, Actuator mounted Supply : 12-36 VDC, Output : 4-20 m A
Provided
5.4
Remote Position indicator
Available in servo controller Digital : 0-100 %
Provided
5.5
Servo controller (Valve positioner) Panel Mounted
Input signal : 4-20 m A, Output : 4-20 m A Feed back : 0-500 Ohms, supply 230 V AC, This will have auto calibration facility.
Provided
5.6 Interface Card
Input signal : 4-20 m A, Feed back : 100-235 Ohms,
Provided
5.7 Local Push Button Station
This will consist of Auto /Off / Manual selector switch, Open/Close push buttons.
Provided
6 GENERAL POINTS 6.1 Inspection By Customer at our works
6.2 T. C.& Manuals 2 Sets with unit 6.3 Warranty 18 months from the date of supply or 12 months from the date of installation
which ever is earlier. 6.4 Packing Thermo cool Packing Housed in corrugated Box
SPECIAL NOTE :
1358-SERIES Electrically Operated Plastic Ball Valve Technical Specifications
Data Sheet Ref. No : SU-1358-00002
SUDE PUNE / BANGALORE
MODEL NO.: 1358\50\PVC\PVC\T\ONF\BSP\SD-1000-05\2LS
Quotation Ref. No Quotation Date
1. ITEM ASSEMBLY OF 2 WAY PLASTIC BALL VALVE FITTED WITH SINGLE PHASE QUARTER TURN ELECTRIC ACTUATOR
2. MAKE SUDE 3 APPLICATION 6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE Valve Size 50mm End connection BSP Screwed Body Material PVC Ball Material PVC Seating material Teflon Flowing medium Acid
Pressure 10 Bar
Temperature Ambient
Characteristic On/Off Type
Fitted with
Sdtork Make Single Phase Quarter Turn Electric Actuator Supply Voltage 230 V AC.
ACTUATOR DETAILS 3.1 Model SD-1000-05 3.2 Output motion type Linear 3.3 Output Torque ( Nm ) 50 Nm 3.4 Output speed ( Sec/90 °) 17 sec/90° 3.5 Manual hand wheel PROVIDED 3.6 Travel limit switches
2 Nos Type : 1 NO + 1 NC, change over contact, contact rating: 5 A, 230 V AC
3.7 Torque limit switches Not required, AS 1000-series actuator are provided with stall duty motor
3.8 Local indicator PROVIDED 3.9 Class of Protection IP67 3.10 Weight of the actuator (Kgs.) 9 kgs. 3.11 Duty S2-10 min 3.12 Mounting 3.14 G. A. Drawing Reference No 3.15 Electrical Wiring Diagram Ref, No MOTOR DETAILS 4.1 Type Reversible Single Phase Synchronous Stall Duty Motor 4.2 Supply 230 V +/- 10 %, 50 Hz +/- 5 % AC Supply 4.3 Duty S2-10 min / S-4-30 % 1200 Cycles/ hr. 4.4 Insulation Class F 4.5 Rating ( Watts) 110 Watts OPTIONAL ACCESSORIES
5.1
Feedback Potentiometer
Out put : 100-235 Ohms Not Provided
5.2
Additional Limit Switches
Qty : 2 nos. Type : 1 NO + 1 NC, Change over contact, Contact rating: 5 A, 230VAC
Provided
5.3
Two Wire Transmitter Type : Two wire, Actuator mounted Supply : 12-36 VDC, Output : 4-20 m A
Not Provided
5.4
Remote Position indicator
Available in servo controller Digital : 0-100 %
Not Provided
5.5
Servo controller (Valve positioner) Panel Mounted
Input signal : 4-20 m A, Output : 4-20 m A Feed back : 0-500 Ohms, supply 230 V AC, This will have auto calibration facility.
Not Provided
5.6 Interface Card Actuator Mounted
Input signal : 4-20 m A, Feed back : 100-235 Ohms,
Not Provided
5.6 Control Panel
This will consist of 2 nos. of Control Relay with required control voltage (If not specify, control voltage will be 230 VAC ) Auto / Manual selector switch, Open/Close push buttons, emergency stop button & MCB.
Not Provided
5.7 Local Push Button Station
This will consist of Auto /Off / Manual selector switch, Open/Close push buttons.
Not Provided
6 GENERAL POINTS 6.1 Inspection By Customer at our works
6.2 T. C.& Manuals 2 Sets with unit 6.3 Warranty 18 months from the date of supply or 12 months from the date of installation
which ever is earlier. 6.4 Packing Thermo cool Packing Housed in corrugated Box
SPECIAL NOTE :
1362-SERIES Pneumatically Operated Ball Valve Technical Specifications
Data Sheet Ref. No : SU-1362-00001
SUDE PUNE / BANGALORE
MODEL NO.: 1362\50\40\BSP\RB\CS\S6\T\PROP\DA05\VP\ITP\PT
Quotation Ref. No Quotation Date
1. ITEM ASSEMBLY OF 2 WAY BALL VALVE FITTED PNEUMATIC ROTARY DOUBLE ACTING ACTUATOR
2. MAKE SUDE 3 APPLICATION Water Industries 6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE Valve Size 50mm Port Size 40mm End connection BSP Screwed Body Material Carbon Steel Ball Material SS316 Seating material Teflon Flowing medium Non-injurious to Body Ball & Seals
Pressure 10 Bar
Type of construction
Reduce Bore Single piece design, Antistatic fire safe Ball
valve
Temperature Ambient
Characteristic Proportionate
Fitted with
Sude Make Pneumatic DA05 Double Acting Actuator, Signal Pressure: 5.5 to 8.5 bar, Quality of air: Filtered & Clean Dry Air
4 PNEUMATIC ACTUATOR DETAILS 4.1 Type Double 4.2 Model DA05 4.3 Spring Clip Steel 4.4 Double Acting Cap Aluminium Alloy 4.5 Cap O-Ring N.B.R 4.6 Piston Polyarilamide 4.7 Cylinder Aluminium Alloy 4.8 Washer Polyamide 4.9 Spring Clip Steel 4.9 Position Indicator Polyamide 4.10 Piston Guide Polyacetal 4.11 Guide Ring Polyacetal 4.12 Piston O-Ring N.B.R 4.13 O-Ring N.B.R 4.14 Springs Set DIN-17223-C 4.15 Spring Return Cap Aluminium Alloy 4.16 Shaft AISI-303 Stainless Steel 4.17 Signal Pressure 5.5 to 8.5 Bar
4.18 Quality Of Air Filtered & Clean Dry Air 4.19 Opening and Closing Time 0.28 [Open] & 0.28 [Close] 5 OPTIONAL ACCESSORIES
5.1 Valve Positioner Input signal: 60 PSI & 3 to 15 PSI Provided 5.2 I to P Converter Input signal: 22 PSI & 4-20mA Provided 5.3 Position
Transmitter Output: 4-20mA Provided
6 GENERAL POINTS 6.1 Inspection By Customer at our works
6.2 T. C.& Manuals 2 Sets with unit 6.3 Warranty 18 months from the date of supply or 12 months from the date of
installation which ever is earlier. 6.4 Packing Thermo cool Packing Housed in corrugated Box
SPECIAL NOTE :
1362-SERIES Pneumatically Operated Ball Valve Technical Specifications
Data Sheet Ref. No : SU-1362-00002
SUDE
PUNE / BANGALORE
MODEL NO.: 1362\25\20\RB\S6\S6\T\ONF\FL15\DA00 \1182B\2WNCMID\06\3.1\BSP\BR\S4\BN \ONF\SPC1\230VAC\GP\1182B\2WNCMID\15\8.0\BSP\S4\S4\BN\ONF\SPC2\230VAC\GP
Quotation Ref. No Quotation Date
1. ITEM ASSEMBLY OF 2 WAY BALL VALVE FITTED PNEUMATIC ROTARY DOUBLE ACTING ACTUATOR
2. MAKE SUDE 3 APPLICATION Oil Weighing Machine 6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE Valve Size 25mm Port Size 20mm End connection Flanged to ASA150RF Body Material SS316 Ball Material SS316 Seating material Teflon Flowing medium Oil
Pressure 10 Bar
Type of construction Reduce Bore Single piece design
Temperature Ambient
Characteristic On/Off Type
Fitted with
Sude Make Pneumatic DA00 Double Acting Actuator, Signal Pressure: 5.5 to 8.5 bar, Quality of air: Filtered and Lubricated
4 PNEUMATIC ACTUATOR DETAILS 4.1 Type Double 4.2 Model DA00 4.3 Spring Clip Steel 4.4 Double Acting Cap Aluminium Alloy 4.5 Cap O-Ring N.B.R 4.6 Piston Polyarilamide 4.7 Cylinder Aluminium Alloy 4.8 Washer Polyamide 4.9 Spring Clip Steel 4.9 Position Indicator Polyamide 4.10 Piston Guide Polyacetal 4.11 Guide Ring Polyacetal 4.12 Piston O-Ring N.B.R 4.13 O-Ring N.B.R 4.14 Springs Set DIN-17223-C 4.15 Spring Return Cap Aluminium Alloy 4.16 Shaft AISI-303 Stainless Steel
4.17 Signal Pressure 5.5 to 8.5 Bar 4.18 Quality Of Air Filtered and Lubricated 4.19 Opening and Closing Time 0.28 [Open] & 0.28 [Close] 5 OPTIONAL ACCESSORIES
5.1 Two Numbers 2 Way Midget type Direct Acting Solenoid Valve
Normally Closed Construction of ¼” size – 1 no. & ½” – 1 no. having Coil voltage of 230 V AC Supply in General Purpose Housing, Input signal: Pulse from the controller
Provided
6 GENERAL POINTS 6.1 Inspection By Customer at our works
6.2 T. C.& Manuals 2 Sets with unit 6.3 Warranty 18 months from the date of supply or 12 months from the date of installation
which ever is earlier. 6.4 Packing Thermo cool Packing Housed in corrugated Box
SPECIAL NOTE :
1362-SERIES Pneumatically Operated Ball Valve Technical Specifications
Data Sheet Ref. No : SU-1362-00003
SUDE PUNE / BANGALORE
MODEL NO.: 1362\200\150\RB\S6\S6\T\ONF\FL15\DA40\1184D\4W5P3PDCPOP\06\6.0\BSP\AL\S4\BN\SPC1\230VAC\GP\WPLSB\FRL\GB
Quotation Ref. No Quotation Date
1. ITEM ASSEMBLY OF 2 WAY BALL VALVE FITTED PNEUMATIC ROTARY DOUBLE ACTING ACTUATOR
2. MAKE SUDE 3 APPLICATION Water / Oil Industries 6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE Valve Size 200mm Port Size 150mm End connection Flanged to ASA150RF Body Material SS316 Ball Material SS316 Seating material Teflon Flowing medium Non-injurious to Body Ball & Seals
Pressure 10 Bar
Type of construction
Reduce Bore Single piece design, Antistatic fire safe Ball
valve
Temperature Ambient
Characteristic On/Off Type
Fitted with
Sude Make Pneumatic DA40 Double Acting Actuator, Signal Pressure: 5.5 to 8.5 bar, Quality of air: Filtered and Lubricated
4 PNEUMATIC ACTUATOR DETAILS 4.1 Type Double 4.2 Model DA40 4.3 Spring Clip Steel 4.4 Double Acting Cap Aluminium Alloy 4.5 Cap O-Ring N.B.R 4.6 Piston Polyarilamide 4.7 Cylinder Aluminium Alloy 4.8 Washer Polyamide 4.9 Spring Clip Steel 4.9 Position Indicator Polyamide 4.10 Piston Guide Polyacetal 4.11 Guide Ring Polyacetal 4.12 Piston O-Ring N.B.R 4.13 O-Ring N.B.R 4.14 Springs Set DIN-17223-C 4.15 Spring Return Cap Aluminium Alloy 4.16 Shaft AISI-303 Stainless Steel
4.17 Signal Pressure 5.5 to 8.5 Bar 4.18 Quality Of Air Filtered and Lubricated 4.19 Opening and Closing
Time 0.28 [Open] & 0.28 [Close]
5 OPTIONAL ACCESSORIES
5.1 4 Way 5 Port 3 position Double Coil poppet type solenoid valve
Of ¼” size having Aluminum body with Coil voltage of 230 V AC Supply
Provided
5.2 Weather Proof Limit switch box
Consisting of 2 nos micro switches having 1 NO + 1 NC contacts for sensing end position of the valve
Provided
5.3 Filter Regulator & Lubricator
Of ¼” Size supplied with Gauge Provided
5.4 Gear Box For Manual operation Provided 6 GENERAL POINTS 6.1 Inspection By Customer at our works
6.2 T. C.& Manuals 2 Sets with unit 6.3 Warranty 18 months from the date of supply or 12 months from the date of installation
which ever is earlier. 6.4 Packing Thermo cool Packing Housed in corrugated Box
SPECIAL NOTE :
1368-SERIES Pneumatically Operated Plastic Ball Valve Technical Specifications
Data Sheet Ref. No : SU-1368- 00001
SUDE PUNE / BANGALORE
1368\50\BSP\PVC\PVC\T\PROP\DA05\EPPOS\FB\PT
Quotation Ref. No Quotation Date
1. ITEM ASSEMBLY OF 2 WAY PLASTIC BALL VALVE FITTED PNEUMATIC ROTARY DOUBLE ACTING ACTUATOR
2. MAKE SUDE 3 APPLICATION 6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE Valve Size 50mm End connection BSP Screwed Body Material PVC Ball Material PVC Seating material Teflon Flowing medium Acid
Pressure 10 Bar
Temperature Ambient
Characteristic Proportionate
Fitted with
Sude Make Pneumatic DA05 Double Acting Actuator, Signal Pressure: 5.5 to 8.5 bar, Quality of air: Filtered & Clean Dry Air
4 PNEUMATIC ACTUATOR DETAILS 4.1 Type Double 4.2 Model DA05 4.3 Spring Clip Steel 4.4 Double Acting Cap Aluminium Alloy 4.5 Cap O-Ring N.B.R 4.6 Piston Polyarilamide 4.7 Cylinder Aluminium Alloy 4.8 Washer Polyamide 4.9 Spring Clip Steel 4.9 Position Indicator Polyamide 4.10 Piston Guide Polyacetal 4.11 Guide Ring Polyacetal 4.12 Piston O-Ring N.B.R 4.13 O-Ring N.B.R 4.14 Springs Set DIN-17223-C 4.15 Spring Return Cap Aluminium Alloy 4.16 Shaft AISI-303 Stainless Steel 4.17 Signal Pressure 5.5 to 8.5 Bar 4.18 Quality Of Air Filtered & Clean Dry Air 4.19 Opening and Closing
Time 0.28 [Open] & 0.28 [Close]
5 OPTIONAL ACCESSORIES
5.1 Siemens make Electro Pneumatic Positioner
Having Input supply: 60 PSI & 4-20mA, Output supply: 4-20mA, Inbuilt with Position Transmitter
Provided
6 GENERAL POINTS 6.1 Inspection By Customer at our works
6.2 T. C.& Manuals 2 Sets with unit 6.3 Warranty 18 months from the date of supply or 12 months from the date of installation
which ever is earlier. 6.4 Packing Thermo cool Packing Housed in corrugated Box
SPECIAL NOTE :
1368-SERIES Pneumatically Operated Plastic Ball Valve Technical Specifications
Data Sheet Ref. No : SU-1368-00002 SUDE
PUNE / BANGALORE MODEL NO.: 1368\50\BSP\PVC\PVC\T\ONF\DA05\AFR\ALR\2FCV\WPLSB
Quotation Ref. No Quotation Date
1. ITEM ASSEMBLY OF 2 WAY PLASTIC BALL VALVE FITTED PNEUMATIC ROTARY DOUBLE ACTING ACTUATOR
2. MAKE SUDE 3 APPLICATION 6 TECHNICAL SPECIFICATION OF 2 WAY BALL VALVE Valve Size 50mm End connection BSP Screwed Body Material PVC Ball Material PVC Seating material Teflon Flowing medium Acid
Pressure 10 Bar
Temperature Ambient
Characteristic On/Off Type
Fitted with
Sude Make Pneumatic DA05 Double Acting Actuator, Signal Pressure: 5.5 to 8.5 bar, Quality of air: Filtered and Lubricated
4 PNEUMATIC ACTUATOR DETAILS 4.1 Type Double 4.2 Model DA05 4.3 Spring Clip Steel 4.4 Double Acting Cap Aluminium Alloy 4.5 Cap O-Ring N.B.R 4.6 Piston Polyarilamide 4.7 Cylinder Aluminium Alloy 4.8 Washer Polyamide 4.9 Spring Clip Steel 4.9 Position Indicator Polyamide 4.10 Piston Guide Polyacetal 4.11 Guide Ring Polyacetal 4.12 Piston O-Ring N.B.R 4.13 O-Ring N.B.R 4.14 Springs Set DIN-17223-C 4.15 Spring Return Cap Aluminium Alloy 4.16 Shaft AISI-303 Stainless Steel 4.17 Signal Pressure 5.5 to 8.5 Bar 4.18 Quality Of Air Filtered and Lubricated 4.19 Opening and Closing Time 0.28 [Open] & 0.28 [Close]
5 OPTIONAL ACCESSORIES
5.1 Air Filter Regulator Of ¼” Size supplied with Gauge Provided 5.2 Air Lock Relay Provided 5.3 Flow Control valve 2 nos for Slow opening & Slow closing Provided 5.2 Weather Proof
Limit switch box Consisting of 2 nos micro switches having 1 NO + 1 NC contacts for sensing end position of the valve
Provided
6 GENERAL POINTS 6.1 Inspection By Customer at our works
6.2 T. C.& Manuals 2 Sets with unit 6.3 Warranty 18 months from the date of supply or 12 months from the date of
installation which ever is earlier. 6.4 Packing Thermo cool Packing Housed in corrugated Box
SPECIAL NOTE :