ba245o/98/en/06.09 guided level radar 120782 06/09 01...
TRANSCRIPT
BA245O/98/en/06.0952013052120782 06/09 01
Valid as a software versionV 01.04.02
Guided Level RadarPulscon LTC withHART/4 mA ... 20 mA andPROFIBUS PA
Description of Instrument Functions
HA R TR
FIELD COMMUNICATION PROTOCOL
Pulscon LTCBasis Setup
DO
CT
-009
4A06
/200
912
0782
2
Brief overview
SD
UB
F
L
D
E
LN
flange:reference pointofmeasurement
��������
������ �
���� ���������
�������
���� ���������
������ �
�����
�������������
���� �������
����������� �
���
��������� �
���������� �
(des
crip
tion
see
BA
245
O)
basi
c se
tup
(sta
ndar
d)op
tion
E = empty calibr. (= zero) LN = probe lengthsetting in 005 setting in 033
F = full calibr. (= span) UB = upper blocking distancesetting in 006 setting in 059
D = distance (distance flange/product) SD = safety distancedisplay in 0A5 setting in 015
L = leveldisplay in 0A6
Pulscon LTCTable of Contents
DO
CT
-009
4A06
/200
912
0782
3
Brief overview . . . . . . . . . . . . . . . . . . . . . . . . 2
1 Notes on use . . . . . . . . . . . . . . . . . . . . . 51.1 Using the table of contents to locate
a function description . . . . . . . . . . . . . . . . . . . . . . . 51.2 Using the graphic of the function menu to
locate a function description . . . . . . . . . . . . . . . . . . 51.3 Using the index of the function menu to
locate a function description . . . . . . . . . . . . . . . . . . 51.4 General structure of the operating menu. . . . . . . . . 6
1.5 Display and operating elements . . . . . . . . . . . . . . . 7
1.6 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2 Function Pulscon LTC . . . . . . . . . . . . 11
3 Function group "basic setup" (00). . . 133.1 Function "measured value" (000) . . . . . . . . . . . . . 13
3.2 Function "tank properties" (002) . . . . . . . . . . . . . . 13
3.3 Function "medium property" (003). . . . . . . . . . . . . 143.4 Function "process propert." (004) . . . . . . . . . . . . . 15
3.5 Function "end of probe" (030) . . . . . . . . . . . . . . . . 15
3.6 Function "probe length" (031) . . . . . . . . . . . . . . . . 163.7 Function "probe" (032). . . . . . . . . . . . . . . . . . . . . . 16
3.8 Function "probe length" (033) . . . . . . . . . . . . . . . . 16
3.9 Function "determine length" (034) . . . . . . . . . . . . . 173.10 Function "empty calibr." (005) . . . . . . . . . . . . . . . . 17
3.11 Function "full calibr." (006). . . . . . . . . . . . . . . . . . . 18
3.12 Display (008) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 183.13 Function "check distance" (051) . . . . . . . . . . . . . . 19
3.14 Function "range of mapping" (052) . . . . . . . . . . . . 20
3.15 Function "start mapping." (053) . . . . . . . . . . . . . . . 203.16 Display (008) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
4 Function "safety settings" (01) . . . . . 224.1 Function "output on alarm" (010). . . . . . . . . . . . . . 22
4.2 Function "output on alarm" (011), HART only . . . . 24
4.3 Function "outp. echo loss" (012) . . . . . . . . . . . . . . 24
4.4 Function "ramp %span/min" (013). . . . . . . . . . . . . 254.5 Function "delay time" (014) . . . . . . . . . . . . . . . . . . 26
4.6 Function "safety distance" (015) . . . . . . . . . . . . . . 26
4.7 Function "in safety dist." (016). . . . . . . . . . . . . . . . 264.8 Function "ackn. alarm" (017) . . . . . . . . . . . . . . . . . 28
4.9 Function "overspill prot." (018) . . . . . . . . . . . . . . . 28
4.10 Function "broken probe det" (019). . . . . . . . . . . . . 28
5 Function group "length adjustment" (03). . . . . . . . . . . 29
5.1 Function "end of probe" (030) . . . . . . . . . . . . . . . . 29
5.2 Function "probe length" (031) . . . . . . . . . . . . . . . . 29
5.3 Function "probe" (032). . . . . . . . . . . . . . . . . . . . . . 295.4 Function "probe length" (033) . . . . . . . . . . . . . . . . 30
5.5 Function "determine length" (034) . . . . . . . . . . . . . 30
6 Function group "linearisation" (04) . . 316.1 Function "level/ullage" (040). . . . . . . . . . . . . . . . . . 316.2 Function "linearisation" (041) . . . . . . . . . . . . . . . . . 32
6.3 Function "customer unit" (042) . . . . . . . . . . . . . . . . 36
6.4 Function "table no." (043) . . . . . . . . . . . . . . . . . . . . 376.5 Function "input level" (044). . . . . . . . . . . . . . . . . . . 37
6.6 Function "input volume" (045) . . . . . . . . . . . . . . . . 38
6.7 Function "max. scale" (046) . . . . . . . . . . . . . . . . . . 386.8 Function "diameter vessel" (047) . . . . . . . . . . . . . . 38
7 Function group "extended calibr." (05) 397.1 Function "selection" (050). . . . . . . . . . . . . . . . . . . . 39
7.2 Function "check distance" (051) . . . . . . . . . . . . . . . 39
7.3 Function "range of mapping" (052). . . . . . . . . . . . . 407.4 Function "start mapping" (053) . . . . . . . . . . . . . . . . 41
7.5 Function "pres. map dist." (054) . . . . . . . . . . . . . . . 41
7.6 Function "delete mapping" (055) . . . . . . . . . . . . . . 417.7 Function "echo quality" (056) . . . . . . . . . . . . . . . . . 42
7.8 Function "offset" (057) . . . . . . . . . . . . . . . . . . . . . . 42
7.9 Function "output damping" (058) . . . . . . . . . . . . . . 427.10 Function "upper block. dist" (059). . . . . . . . . . . . . . 43
8 Function group "output" (06), - "profibus param." (06), PROFIBUS PA only . . . . . . . . . . . . . . . 45
8.1 Function "commun. address" (060), HART only. . . 458.2 Function "instrument addr." (060),
PROFIBUS PA only . . . . . . . . . . . . . . . . . . . . . . . . 458.3 Function "no. of preambels" (061), HART only. . . . 45
8.4 Function "ident number" (061),PROFIBUS PA only . . . . . . . . . . . . . . . . . . . . . . . . 46
8.5 Function "low output limit" (062), HART only . . . . . 46
8.6 Function "set unit to bus" (062), PROFIBUS PA only . . . . . . . . . . . . . . . . . . . . . . . . 46
8.7 Function "curr. output mode" (063), HART only . . . 47
8.8 Function "out value" (063), PROFIBUS PA only . . 478.9 Function "fixed cur. value" (064), HART only . . . . . 48
8.10 Function "out status" (064), PROFIBUS PA only . . 48
8.11 Function "simulation" (065). . . . . . . . . . . . . . . . . . . 498.12 Function "simulation value" (066) . . . . . . . . . . . . . . 50
8.13 Function "output current" (067), HART only . . . . . . 50
8.14 Function "2nd cyclic value" (067), PROFIBUS PA only . . . . . . . . . . . . . . . . . . . . . . . . 50
8.15 Function "4mA value" (068), HART only . . . . . . . . 508.16 Function "select v0h0" (068),
PROFIBUS PA only . . . . . . . . . . . . . . . . . . . . . . . . 518.17 Function "20mA value" (069), HART only . . . . . . . 51
8.18 Function "display value" (069), PROFIBUS PA only . . . . . . . . . . . . . . . . . . . . . . . . 51
9 Function group "envelope curve" (0E) . . . . . . . . . . . . . 52
9.1 Function "plot settings" (0E1) . . . . . . . . . . . . . . . . . 52
9.2 Function "recording curve" (0E2) . . . . . . . . . . . . . . 529.3 Function "envelope curve display" (0E3) . . . . . . . . 53
Pulscon LTCTable of Contents
DO
CT
-009
4A06
/200
912
0782
4
10 Function group "display" (09) . . . . . . . 5510.1 Function "language" (092) . . . . . . . . . . . . . . . . . . 5510.2 Function "back to home" (093) . . . . . . . . . . . . . . . 55
10.3 Function "format display" (094). . . . . . . . . . . . . . . 56
10.4 Function "no.of decimals" (095) . . . . . . . . . . . . . . 5610.5 Function "sep. character" (096) . . . . . . . . . . . . . . 56
10.6 Function "display test" (097) . . . . . . . . . . . . . . . . . 57
11 Function group "diagnostics" (0A) . . . 5811.1 Function "present error" (0A0) . . . . . . . . . . . . . . . 59
11.2 Function "previous error" (0A1) . . . . . . . . . . . . . . 5911.3 Function "clear last error" (0A2) . . . . . . . . . . . . . . 59
11.4 Function "reset" (0A3). . . . . . . . . . . . . . . . . . . . . . 60
11.5 Function "unlock parameter" (0A4). . . . . . . . . . . . 6111.6 Function "measured dist." (0A5) . . . . . . . . . . . . . . 62
11.7 Function "measured level" (0A6) . . . . . . . . . . . . . 63
11.8 Function "detection window" (0A7) (from Software 01.04.00) . . . . . . . . . . . . . . . . . . . 63
11.9 Function "application par." (0A8) . . . . . . . . . . . . . 64
12 Function group "system parameters" (0C) . . . . . . . . . . 65
12.1 Function "tag no." (0C0). . . . . . . . . . . . . . . . . . . . . 65
12.2 Function "profile version" (0C1), PROFIBUS PA only . . . . . . . . . . . . . . . . . . . . . . . . 65
12.3 Function "protocol+sw-no." (0C2) . . . . . . . . . . . . . 65
12.4 Function "serial no." (0C4) . . . . . . . . . . . . . . . . . . . 6512.5 Function "distance unit" (0C5) . . . . . . . . . . . . . . . . 66
12.6 Function "download mode" (0C8) . . . . . . . . . . . . . 67
13 Function group "service" (0D) . . . . . . . 68
14 Envelope curve (echo curve) . . . . . . . . 6914.1 Envelope curve with the PACTwareTM . . . . . . . . . . 69
15 Trouble-shooting. . . . . . . . . . . . . . . . . . 7015.1 Trouble-shooting instructions. . . . . . . . . . . . . . . . . 7115.2 System error messages. . . . . . . . . . . . . . . . . . . . . 72
15.3 Application errors . . . . . . . . . . . . . . . . . . . . . . . . . . 73
15.4 Software history . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Index function menu . . . . . . . . . . . . . . . . . . 75
Pulscon LTCNotes on use
DO
CT
-009
4A06
/200
912
0782
5
1 Notes on use
You have various options for accessing the descriptions of instrument functions or how to enter parameters.
1.1 Using the table of contents to locate a function description
All the functions are listed in the table of contents sorted by function group (e. g. "basic setup", "safety settings", etc.). You can access a more detailed description of a function by using a page reference/link.
The table of contents is on page 3.
1.2 Using the graphic of the function menu to locate a function description
This guides you step by step from the highest level, the function groups, to the exact function description you require.
All the available function groups and instrument functions are listed in the table (page 11). Select your required function group or function. You can access an exact description of the function group or function by using a page reference/link.
1.3 Using the index of the function menu to locate a function description
To simply navigation within the function menu, each function has a position which is shown in the display. You can access each function via a page reference/link in the function menu index (page 75) which lists all the function names alphabetically and numerically.
Pulscon LTCNotes on use
DO
CT
-009
4A06
/200
912
0782
6
1.4 General structure of the operating menu
The operating menu is made up of two levels:
• Function groups (00, 01, … , 0C, 0D):The individual operating Selection of the instrument are split up roughly into different function groups. The function groups that are available include, e. g.: "basic setup", "safety settings", "output", "display", etc.
• Functions (001, 002, 003, …, 0D8, 0D9):Each function group consists of one or more functions. The functions perform the actual operation or parameterisation of the instrument. Numerical values can be entered here and parameters can be selected and saved. The available functions of the "basic setup" (00) function group include, e. g.: "tank shape" (002), "medium property" (003), "process cond." (004), "empty calibr." (005), etc.
If, for example, the application of the instrument is to be changed, carry out the following procedure:
• Select the "basic setup" (00) function group.• Select the "tank properties" (002) (where the existing tank properties is selected).
1.4.1 Identifying the functions
For simple orientation within the function menus, for each function a position is shown on the display.
The first two digits identify the function group:
The third digit numbers the individual functions within the function group:
Here after the position is always given in brackets (e. g. "tank properties" (002)) after the described function.
• basic setup 00• safety settings 01• linearisation 04...
• basic setup 00 → • tank properties. 002• medium property 003• process cond. 004...
Pulscon LTCNotes on use
DO
CT
-009
4A06
/200
912
0782
7
1.5 Display and operating elements
Four lines with 20 characters each. Display contrast adjustable through key combination.
The LTC-Z02 LCD display can be removed to ease operation by simply pressing the snap-fit (see graphic above). It is connected to the device by means of a 500 mm cable.
1.5.1 Display
Liquid crystal display (LCD):
ENDRESS+HA USER
MICR OPILOT II
IP 65
Order Code:Ser.-No.:
MessbereichMeasuring rangeU 16...36 V DC
4...20 mA
max. 20 m
Made in
Ger
man
y M
aulb
urg
T>70 C :
A
t >85 C
E+–
LCD(Liquid crystal display)
Symbols3 keys
Snap-fit
XX
X
XS
S
OO FF
F
F
HOME
FG00 F000 F001 F002 F003 F004 ...
FG01
FG02
FG03
FG04
FG05
FG06
FG07
...
����� !"
� � ��# $� �
E+– Bargraph
Selection list
Help text
Envelope
curve
Headline Position indicator
Main value UnitSymbol
Function groups (FG) � Functions (F)
Pulscon LTCNotes on use
DO
CT
-009
4A06
/200
912
0782
8
1.5.2 Display symbols
The following table describes the symbols that appear on the liquid crystal display:
1.5.3 Key assignment
The operating elements are located inside the housing and are accessible for operation by opening the lid of the housing.
Function of the keys
Symbol Meaning
ALARM_SYMBOLThis alarm symbol appears when the instrument is in an alarm state. If the symbol flashes, this indicates a warning.
LOCK_SYMBOLThis lock symbol appears when the instrument is locked, i. e. if no input is possible.
COM_SYMBOLThis communication symbol appears when a data transmission via e. g. HART or PROFIBUS PA is in progress.
Key(s) Meaning
O or V Navigate upwards in the selection listEdit numeric value within a function
S or W Navigate downwards in the selection listEdit numeric value within a function
X or Z Navigate to the left within a function group
F Navigate to the right within a function group, confirmation.
O and For
S and FContrast settings of the LCD
O and S and F
Hardware lock/unlockAfter a hardware lock, an operation of the instrument via display orcommunication is not possible!The hardware can only be unlocked via the display. An unlock parameter must be entered to do so.
Pulscon LTCNotes on use
DO
CT
-009
4A06
/200
912
0782
9
1.5.4 Operation with the LTC-Z02
1. Change from measured value display to Group selection by pressing F.2. Press S or O to select the required Function group (e. g. "basic setup" (00)) and
confirm by pressing F → first function (e. g. "tank shape" (002)) is selected. The active selection is marked by a in front of the menu text.
3. Activate Edit mode with O or S .
Selection menus
a) Select the required Parameter in selected function (e. g. "tank shape" (002)) with S or O .
b)F confirms selection; → appears in front of the selected parameter.c) F confirms the edited value; → system quits edit mode.d)O and S (= Q) interrupts selection; → system quits edit mode.
Typing in numerals and text
a) Press O or S to edit the first character of the numeral/text (e. g. "empty calibr." (005)).
b)F positions the cursor at the next character; → continue with a. until you have completed your input.
c) If a ↵ symbol appears at the cursor, press F to accept the value entered;→ system quits edit mode.
d)O and S (= Q) interrupts the input; → system quits edit mode.
4. Press F to select the next function (e. g. "medium property" (003)).5. Press O and S (= Q) once; → return to previous function (e. g. "tank
shape" (002)).Press O and S (= Q) twice; → return to Group selection.
6. Press O and S (= Q) to return to Measured value display.
E+–
X XX
X
S
S S
OO O
F F
> 3 s
F
...
2x
...
...
%�� ����
& �������������������
�������������
���� �������
����������� �
��������
������ �
��������������
�����������
������'��
����� ��
���� ������
������ � ��
Pulscon LTCNotes on use
DO
CT
-009
4A06
/200
912
0782
10
1.6 Commissioning
1.6.1 Switching on the measuring device
When the instrument is switched on for the first time, the following messages appear on the display:
After 5 s, the following message appears
After 5 s, the following message appears (e. g. on HART devices)
After 5 s or after you have pressed F the following message appears
Select the language(this message appears the first time the instrument is switched on)
Select the basic unit(this message appears the first time the instrument is switched on)
The current message value is displayed
After F is pressed, you reach the group selection
This selection enables you to perform the basic setup
E+–
Pulscon LTCFunction Pulscon LTC
DO
CT
-009
4A06
/200
912
0782
11
2 Function Pulscon LTC
Function group Function Description
basic setup 00 measured value 000 page 13
(see page 13) tank properties 002 page 13
medium property 003 page 14
process propert. 004 page 15
end of probe 030 page 15
probe length 031 page 16
probe 032 page 16
probe length 033 page 16
determine length 034 page 17
empty calibr. 005 page 17
full calibr. 006 page 18
check distance 051 page 19
range of mapping 052 page 20
start mapping 053 page 20
safety settings 01 output on alarm 010 page 22
(see page 22) output on alarm (HART only) 011 page 24
outp. echo loss 012 page 24
ramp %span/min 013 page 25
delay time 014 page 26
safety distance 015 page 26
in safety dist. 016 page 26
ackn. alarm 017 page 28
overspill prot. 018 page 28
broken probe det 019 page 28
length adjustment 03 end of probe 030 page 29
(see page 29) probe length 031 page 29
probe 032 page 29
probe length 033 page 30
determine length 034 page 30
Linearisation 04 level/ullage 040 page 31
(see page 31) linearisation 041 page 32
customer unit 042 page 36
table no. 043 page 37
input level 044 page 37
input volume 045 page 38
max. scale 046 page 38
diameter vessel 047 page 38
extended calibr. 05 selection 050 page 39
(see page 39) check distance 051 page 39
range of mapping 052 page 40
start mapping 053 page 41
pres. map dist. 054 page 41
delete mapping 055 page 41
echo quality 056 page 42
offset 057 page 42
output damping 058 page 42
upper block. dist 059 page 43
Pulscon LTCFunction Pulscon LTC
DO
CT
-009
4A06
/200
912
0782
12
Function group Function Description
output 06 commun. address (HART only) 060 page 45
PROFIBUS param. 06 instrument addr. (PROFIBUS PA only) 060 page 45
PROFIBUS PA only no. of preambels (HART only) 061 page 45
(see page 45) ident number (PROFIBUS PA only) 061 page 46
low output limit (HART only) 062 page 46
set unit to bus (PROFIBUS PA only) 062 page 46
curr. output mode (only HART) 063 page 47
out value (PROFIBUS PA only) 063 page 47
fixed cur. value (HART only) 064 page 48
out status (PROFIBUS PA only) 064 page 48
simulation 065 page 49
simulation value 066 page 50
output current (HART only) 067 page 50
2nd cyclic value (PROFIBUS PA only) 067 page 50
4mA value (HART only) 068 page 50
select v0h0 (PROFIBUS PA only) 068 page 51
20mA value (HART only) 069 page 51
display value (PROFIBUS PA only) 069 page 51
envelope curve 0E plot settings 0E1 page 52
(see page 52) recording curve 0E2 page 52
envelope curve display 0E3 page 53
display 09 language 092 page 55
(see page 55) back to home 093 page 55
format display 094 page 56
no.of decimals 095 page 56
sep. character 096 page 56
display test 097 page 57
diagnostics 0A present error 0A0 page 59
(see page 58) previous error 0A1 page 59
clear last error 0A2 page 59
reset 0A3 page 60
unlock parameter 0A4 page 61
measured dist. 0A5 page 62
measured level 0A6 page 63
detection window 0A7 page 63
application par. 0A8 page 64
system parameter 0C tag no. 0C0 page 65
(see page 65) Profile Version (PROFIBUS PA only) 0C1 page 65
protocol+sw-no. 0C2 page 65
serial no. 0C4 page 65
distance unit 0C5 page 66
download mode 0C8 page 67
service D00 service level D00 page 68
Pulscon LTCFunction group "basic setup" (00)
DO
CT
-009
4A06
/200
912
0782
13
3 Function group "basic setup" (00)
3.1 Function "measured value" (000)
This function displays the current measured value in the selected unit(see "customer unit" (042)) function). The number of digits after decimal point can be selected in the "no.of decimals" (095) function.
3.2 Function "tank properties" (002)
This function is used to select the tank properties.
Selection:• standard• aluminium tank• plastic tank• bypass/pipe• coax probe• concrete wall
standardThe "standard" option is recommended for normal containers for rod and rope probes.
aluminium tankThe "aluminium tank" option is designed especially for high aluminium silos that cause an increased level of noise when empty. This option is only useful for probes longer than 4 m. For short probes (< 4 m) select the "standard" option!
!Note! If "aluminium tank" is selected, the device calibrates of its own accord when first filled, depending on the medium's properties. Slope errors can, therefore, occur when beginning the first filling procedure.
plastic tankSelect the "plastic tank" option when installing probes in wood or plastic containers without metallic surfaces at the process connection (see installation in plastic containers). When using a metallic surface at the process connection, the "standard" option is sufficient!
!Note! In principle the employment of a metallic surface area should be preferred at the process connection!
E+–
E+–
E+–
Pulscon LTCFunction group "basic setup" (00)
DO
CT
-009
4A06
/200
912
0782
14
bypass/pipe
The "bypass/pipe" option is designed especially for the installation of probes in a bypass or a stilling well. If this option is selected, the upper blocking distance is preset to 100 mm.
coax probeSelect the "coax probe" option when using a coax probe. When this setting is made, the evaluation is adapted to the high sensitivity of the coax probe. This option should, therefore, not be selected when using rope or rod probes.
concrete wallThe "concrete wall" option takes into account the signal-damping property of concrete walls when mounting with < 1 m distance to the wall.
3.3 Function "medium property" (003)
This function is used to select the dielectric constant.
Selection:• unknown• 1.4 ... 1.6 (for coax and rod probe with installation in metallic pipes ≤ DN 150)• 1.6 ... 1.9• 1.9 ... 2.5• 2.5 ... 4.0• 4.0 ... 7.0• > 7.0
The lower group applies to very loose or loosened bulk solids. Reduction of the max. possible measuring range by means of:
• extremely loose surfaces of bulk solids, e. g. bulk solids with low piled density when filled pneumatically.
• Build-up, primarily of moist products.
E+–
Medium group
DC (ε r) Typical bulk solids Typical liquids Measuring range
bare metallic probes PA-coated rope probes
1 1.4 … 1.6 – Condensed gases, e. g. N2, CO2 4 m/157", coax probe –
2 1.6 … 1.9 Plastic granulateWhite lime, special cementSugar
Liquefied gas, e. g. PropaneSolventFrigen/FreonPalm oil
25 m ... 30 m/984" ... 1181"
12.5 m ... 15 m/ 492" ... 590"
3 1.9 … 2.5 Portland cement, plaster Mineral oils, fuels 30 m ... 35 m/ 1181" ... 1378"
–
Flour – – 15 m ... 25 m/ 590" ... 984"
4 2.5 … 4 Grain, seeds – – 25 m ... 30 m/ 984" ... 1181"
Ground stonesSand
Benzene, styrene, tolueneFuranNaphthalene
35 m/1378" 25 m ... 30 m/ 984" ... 1181"
5 4 … 7 Naturally moist (ground) stones, oresSalt
Chlorobenzene, chloroformCellulose sprayIsocyanate, aniline
35 m/1378" 35 m/1378"
6 > 7 Metallic powderCarbon blackCoal
Aqueous solutionsAlcoholsAmmonia
35 m/1378" 35 m/1378"
Pulscon LTCFunction group "basic setup" (00)
DO
CT
-009
4A06
/200
912
0782
15
3.4 Function "process propert." (004)
Use this function to adapt the device reaction to the filling speed in the tank. The setting impacts on an intelligent filter.
Selection:• standard• fast change• slow change• test:no filter
3.5 Function "end of probe" (030)
Use this function to select the polarity of the probe end signal. If the probe end is uncovered or in an insulated attachment, there is a negative probe end signal.
The signal from the probe end is positive if the attachment is grounded.
Selection:• free• tie down isol.• tie down gnd.
E+–
Selection: Standard Fast change Slow change Test: no filter
Application: For all normal applications, bulk solids and fluids at low to medium filling speed and sufficiently large tanks.
Small tanks, primarily with fluids, at high filling speeds.
Applications with strong surface movement, e. g. caused by stirrer, primarily large tanks with slow to medium filling speed.
Shortest reaction time:- For test purposes- Measurement in small
tanks at high filling speeds, if "rapid change" setting is too slow.
2-wire electronics: Dead time: 4 sRise time: 18 s
Dead time: 2 sRise time: 5 s
Dead time: 6 sRise time: 40 s
Dead time: 1 sRise time: 0 s
4-wire electronics: Dead time: 2 sRise time: 11 s
Dead time: 1 sRise time: 3 s
Dead time: 3 sRise time: 25 s
Dead time: 0.7 sRise time: 0 s
E+–
Pulscon LTCFunction group "basic setup" (00)
DO
CT
-009
4A06
/200
912
0782
16
3.6 Function "probe length" (031)
Use this function to select whether the probe length was changed after factory calibration. Only then is it necessary to enter or correct the probe length.
Selection:• modified• not modified
!Note! If "modified" was selected in the "probe length" (031) function, the probe length is defined in the next step.
3.7 Function "probe" (032)
Use this function to select whether the probe is at the time of the commissioning uncovered or covered.
If the probe is uncovered, the Pulscon can determine the probe length automatically "determine length" (034) function. If the probe is covered, a correct entry is required in the "probe length" (033) function.
Selection:• free• covered
3.8 Function "probe length" (033)
Use this function, the probe length can be entered manually.
E+–
E+–
E+–
Pulscon LTCFunction group "basic setup" (00)
DO
CT
-009
4A06
/200
912
0782
17
3.9 Function "determine length" (034)
Use this function, the probe length can be determined automatically.
Due to the mounting conditions, the automatically determined probe length may be larger than the actual probe (typically 20 mm ... 30 mm longer). This has no influence on the measuring accuracy. When entering the empty value for a linearisation, please use the "empty calibration" instead of the automatically determined probe length.
Selection:• length ok• too short• too longAfter selection "too short" or "too long", the calculation of the new value need approx. 10 s.
3.10 Function "empty calibr." (005)
This function is used to enter the distance from the flange (reference point of the measurement) to the minimum level (= zero).
E+–
E+–
0 %
EE = empty calibration (= zero)
E = probe length – lower blocking distancemax
Pulscon LTCFunction group "basic setup" (00)
DO
CT
-009
4A06
/200
912
0782
18
3.11 Function "full calibr." (006)
This function is used to enter the distance from the minimum level to the maximum level (= span).
!Note! The usable measuring range lies between the lower and the upper blocking distance. The values for empty distance (E) and span (F) can be set independently of this.
3.12 Display (008)
The distance measured from the reference point to the product surface and the meas. value calculated with the aid of the empty adjustment are displayed. Check whether the values correspond to the actual meas. value or the actual distance. The following cases can occur:
• Distance correct – meas. value correct continue with the next function "check distance" (051).
• Distance correct – meas. value incorrect check "empty calibr." (005)• Distance incorrect – meas. value incorrect continue with the next function
"check distance" (051).
E+–
100 %
0 %
F F = full calibration (= span)
F = E – upper blocking distancemax
E+–
Pulscon LTCFunction group "basic setup" (00)
DO
CT
-009
4A06
/200
912
0782
19
3.13 Function "check distance" (051)
This function triggers the mapping of interference echoes. To do so, the measured distance must be compared with the actual distance to the product surface. The following options are available for selection:
Selection:• distance = ok• dist. too small• dist. too big• dist. unknown• manual• probe free
distance = okUse this function at part-covered probe. Choosing function "manual" or "probe free" at free probe.
• Mapping is carried out up to the currently measured echo• The range to be suppressed is suggested in the "range of mapping" (052) functionAnyway, it is wise to carry out a mapping even in this case.
!Note! At free probe, the mapping should be confirmed with the choice "probe free".
dist. too small• At the moment, an interference is being evaluated• Therefore, a mapping is carried out including the presently measured echoes• The range to be suppressed is suggested in the "range of mapping" (052) function
dist. too big• This error cannot be remedied by interference echo mapping• Check the application parameters (002), (003), (004) and
"range of mapping" (052) function.
E+–
distance too small distance = ok
Pulscon LTCFunction group "basic setup" (00)
DO
CT
-009
4A06
/200
912
0782
20
dist. unknown
If the actual distance is not known, no mapping can be carried out.
manualA mapping is also possible by manual entry of the range to be suppressed. This entry is made in the "range of mapping" (052) function.
"Caution!The range of mapping must end 0.3 m (12") before the echo of the actual level. In case of empty vessel it is possible to make a map over the whole probe length.
probe freeIf the probe is uncovered, mapping is carried out along the whole probe length.
"Caution!Only begin mapping in this function if the probe is safely uncovered. Otherwise, the device will not make correct measurements!
3.14 Function "range of mapping" (052)
This function displays the suggested range of mapping. The reference point is always the reference point of the measurement (see page 2). This value can be edited by the operator.
For manual mapping, the default value is 0.3 m.
3.15 Function "start mapping." (053)
This function is used to start the interference echo mapping up to the distance given in "range of mapping" (052).
Selection:• off: no mapping is carried out• on: mapping is started
E+–
E+–
Pulscon LTCFunction group "basic setup" (00)
DO
CT
-009
4A06
/200
912
0782
21
3.16 Display (008)
The distance measured from the reference point to the product surface and the meas. value calculated with the aid of the empty alignment are displayed again. Check whether the values correspond to the actual meas. value or the actual distance. The following cases can occur:
• Distance correct – meas. value correct basic setup completed• Distance incorrect – meas. value incorrect a further interference echo mapping
must be carried out "check distance" (051).• Distance correct – meas. value incorrect check "empty calibr" (005)
!Note! After the basic setup, an evaluation of the measurement with the aid of the envelope curve ("envelope curve" (0E) function group) is recommended (see page 52).
E+–
After 3 s, the following message appears
E+–
Pulscon LTCFunction "safety settings" (01)
DO
CT
-009
4A06
/200
912
0782
22
4 Function "safety settings" (01)
4.1 Function "output on alarm" (010)
This function is used to select the reaction of output on an alarm.
Selection:• MIN (<= 3.6mA)• MAX (22mA)• Hold• User specific
MIN (<= 3.6mA)
If the instrument is in alarm state, the output changes as follows:
• HART: MIN-Alarm 3.6 mA• PROFIBUS PA: MIN-Alarm -99999
MAX 110% 22mA
If the instrument is in alarm state, the output changes as follows:
• HART: MAX-Alarm 22 mA• PROFIBUS PA: MAX-Alarm +99999
E+–
E+–
(110 %)
(-10 %)3.6
t
[mA]22
-99999
t
HART PA
HART PA(110 %)
(-10 %)3.6
t
[mA]22 +99999
t
Pulscon LTCFunction "safety settings" (01)
DO
CT
-009
4A06
/200
912
0782
23
Hold
If the instrument is in alarm state, the last measured value is held.
user specific
If the instrument is in alarm state, the output is set to the value configured in "output on alarm" (011) (x mA).
"Caution!
This selection is available for HART devices only!
HART PA(110 %)
(-10 %)3.6
t
[mA]22
-10 %
110 %
t
hold hold
Pulscon LTCFunction "safety settings" (01)
DO
CT
-009
4A06
/200
912
0782
24
4.2 Function "output on alarm" (011), HART only
On alarm, the output current is in mA. This function is active when you selected "user specific" in the "output on alarm" (010) function.
"Caution!
This selection is available for HART devices only!
4.3 Function "outp. echo loss" (012)
Use this function to set the output response on echo loss.
Selection:• hold• ramp %/min• alarm
alarm
On echo loss, the instrument switches to alarm state after an adjustable "delay time" (014). The output response depends on the configuration set in "output on alarm" (010).
E+–
E+–
Pulscon LTCFunction "safety settings" (01)
DO
CT
-009
4A06
/200
912
0782
25
hold
On echo loss, a warning is generated after a definable "delay time" (014). Output is held.
ramp %/min
On echo loss, a warning is generated after a definable "delay time" (014). The output is changed towards 0 % or 100 % depending on the slope defined in "ramp %span/min" (013).
4.4 Function "ramp %span/min" (013)
Ramp slope which defines the output value on echo loss. This value is used if "ramp %span/min" is selected in "outp. echo loss" (012). The slope is given in % of the measuring range per minute.
Δ %
E+–
Pulscon LTCFunction "safety settings" (01)
DO
CT
-009
4A06
/200
912
0782
26
4.5 Function "delay time" (014)
Use this function to enter the delay time (Default = 30 s) after which a warning is generated on echo loss, or after which the instrument switches to alarm state.
4.6 Function "safety distance" (015)
A configurable safety distance is placed before the "upper blocking dist." (059) (see page 43). This distance warns you that any further level increase would make the measurement invalid.
Enter the size of the safety distance here. The default value is: 0.1 m.
4.7 Function "in safety dist." (016)
This function defines the response when the level enters the safety distance.
Selection:• alarm• warning• self holding
E+–
safety distance (015)
safety distance (015)
blocking dist. (059)blocking dist. (059)
E+–
E+–
Pulscon LTCFunction "safety settings" (01)
DO
CT
-009
4A06
/200
912
0782
27
alarm
Instrument enters the defined alarm state ("output on alarm" (011)). The alarm message E651 - "level in safety distance - risk of overspill" is displayed.
If the level drops out of the safety distance, the alarm warning disappears and the instrument starts to measure again.
warning
Instrument displays a warning E651 - "level in safety distance - risk of overspill", but continues to measure. If the level leaves the safety distance, the warning disappears.
self holding
Instrument switches to defined alarm state ("output on alarm" (011)). The alarm message E651 - "level in safety distance - risk of overspill" is displayed.
If the level leaves the safety distance, the measurement continues only after a reset of the self holding (function: "ackn. alarm" (017)).
t
[mA]22SD
110 %
3.6 -10 %
WARNING
Pulscon LTCFunction "safety settings" (01)
DO
CT
-009
4A06
/200
912
0782
28
4.8 Function "ackn. alarm" (017)
This function acknowledges an alarm in case of "self holding".
Selection:• no• yes
noThe alarm is not acknowledged.
yesAcknowledgement takes place.
4.9 Function "overspill prot." (018)
When "german WHG" is selected, various parameters relating to WHG overflow protection are defaulted and the instrument is locked against further operation. Select "Standard" to unlock, the WHG parameter settings are retained.
4.10 Function "broken probe det" (019)
This function activates the automatic recognition of broken probes.Before updating the broken probe detection a mapping must be performed (function "range of mapping" (052) and "start mapping" (053), see page 20).
Selection:• off• on
E+–
E+–
E+–
After 3 s, the following message appears
E+–
Pulscon LTCFunction group "length adjustment" (03)
DO
CT
-009
4A06
/200
912
0782
29
5 Function group "length adjustment" (03)
5.1 Function "end of probe" (030)
Use this function to select the polarity of the probe end signal. If the probe end is uncovered or in an insulated attachment, there is a negative probe end signal.
The signal from the probe end is positive if the attachment is grounded.
Selection:• free• tie down isol.• tie down gnd.
5.2 Function "probe length" (031)
Use this function to select whether the probe length was changed after factory calibration. Only then is it necessary to enter or correct the probe length.
Selection:• modified• not modified
!Note!If "modified" was selected in the "probe length" (031) function, the probe length is defined in the next step.
5.3 Function "probe" (032)
Use this function to select whether the probe is at the time of the commisioning uncovered or covered. If the probe is uncovered, the Pulscon LTC can determine the probe length automatically "determine length" (034). function. If the probe is covered, a correct entry is required in the "probe length" (033) function
Selection:• free• covered
E+–
E+–
E+–
E+–
Pulscon LTCFunction group "length adjustment" (03)
DO
CT
-009
4A06
/200
912
0782
30
5.4 Function "probe length" (033)
Use this function to enter the probe length.
5.5 Function "determine length" (034)
Use this function to determine the probe length automatically. Due to the mounting conditions, the automatically determined probe length may be larger than the actual probe (typically 20 mm ... 30 mm longer). This has no influence on the measuring accuracy. When entering the empty value for a linerisation, please use the "empty calibration" instead of the automatically determined probe length.
Selection:• length ok• too short• too longAfter selecting "length too short" or "length too long" the calculation of the new probe length takes up to approx. 10 s.
E+–
E+–
Pulscon LTCFunction group "linearisation" (04)
DO
CT
-009
4A06
/200
912
0782
31
6 Function group "linearisation" (04)
6.1 Function "level/ullage" (040)
Selection:• level CU• level DU• ullage CU• ullage DU
level CULevel in customer units. The measured value can be linearised. The "linearisation" (041) default value is set to a linear 0 % ... 100 %.
level DULevel in the selected "distance unit" (0C5).
ullage CUUllage in customer units. The value can be linearised. The "linearisation" (041) default value is set to a linear 0 % ... 100 %.
ullage DUUllage in the selected "distance unit" (0C5).
!Note!Reference point for the ullage is "full calibr." (006) (= span).
E+–
E+–
20 mA100 %
4 mA0 %
Level
Ullage
Pulscon LTCFunction group "linearisation" (04)
DO
CT
-009
4A06
/200
912
0782
32
6.2 Function "linearisation" (041)
Linearisation defines the ratio of level to container volume or product weight and allows a measurement in customer units, e. g. metres, hectolitres etc. The measured value in (000) is then displayed in the selected unit.
This function is used to select the linearisation modes.
Selection:• linear• horizontal cyl• manual• semi-automatic• table on• clear table
linearThe tank is linear e. g. a cylindrical vertical tank. You can measure in customer units by entering a maximum volume/weight.
You can select the "customer unit" (042). Define the volume value corresponding to the calibration in "max. scale" (046). This value corresponds to an output of 100 % (= 20 mA for HART).
E+–
0 %4 mA
100 %20 mA
kg, m3 , ft3 , ... = customer unit (42)
(046)max.scale
Pulscon LTCFunction group "linearisation" (04)
DO
CT
-009
4A06
/200
912
0782
33
horizontal cyl
The volume, mass etc. are calculated automatically in cylindrical horizontal tanks by entering the "diameter vessel" (047), the "customer unit" (042) and the "max. scale" (046). The "max. scale" (046) corresponds to an output of 100 % (= 20 mA for HART).
manualIf the level is not proportional to the volume or weight within the set measuring range, you can enter a linearisation table in order to measure in customer units. The requirements are as follows:
• The 32 (max.) value pairs for the linearisation curve points are known.• The level values must be given in ascending order. The curve is monotonously
increasing.• The level heights for the first and last points on the linearisation curve correspond
to empty and full calibration respectively.• The linearisation takes place in the basic setup unit ("distance unit" (0C5)).
Each point (2) in the table is described by a value pair: level (3) and, for example, volume (4). The last value pair defines the 100 % output (= 20 mA for HART).
0 %4 mA
100 %20 mA
kg, m3 , ft3 , ... = Customer unit (042)
Max. scale(046)
Diameter vessel (047)
100 %
0 %4 mA
(2)
(4)
(3)
20 mA
kg, m3 , ft3 , ... = Customer unit (042)
Pulscon LTCFunction group "linearisation" (04)
DO
CT
-009
4A06
/200
912
0782
34
!Note!After making entries into the table, activate it with "table on". The 100 % value (= 20 mA for HART) is defined by the last point in the table.
!Note!Before confirming 0.00 m as the level or 0.00 % as the volume, activate the edit mode with O or S.
Entries can be made into the linearisation table in PACTwareTM using the table editor. You can also display the contents graphically.
Select the table point (Point 3).
Enter the level belonging to Point 3.
Enter the corresponding volume.
Enter a further table point?
Next table point.
E+–
Pulscon LTCFunction group "linearisation" (04)
DO
CT
-009
4A06
/200
912
0782
35
semi-automatic
The tank is filled in stages when the linearisation curve is entered semi-automatically. The Pulscon LTC automatically detects the level and the corresponding volume/weight has to be entered. The procedure is similar to manual table entry, where the level value for each table point is given automatically by the instrument.
!Note!If the tank is emptied, pay attention to the following points:
• The number of points must be known in advance.• The first table number = (32 - number of points).• Entries in "Tab. no." (043) are made in reverse order (last entry = 1).
table onAn entered linearisation table only becomes effective when activated.
clear tableBefore making entries into the linearisation table, any existing tables must be deleted. The linearisation mode automatically switches to linear.
!Note!A linearisation table can be deactivated by selecting "linear" or "horizontal cyl" (or the "level/ullage" (040) function = "level DU", "ullage DU"). It is not deleted and can be reactivated at any time by selecting "table on".
Pulscon LTCFunction group "linearisation" (04)
DO
CT
-009
4A06
/200
912
0782
36
6.3 Function "customer unit" (042)
You can select the customer unit with this function.
Selection:• %• l• hl• m3• dm3• cm3• ft3• us_gal• i_gal• kg• t• lb• ton• m• ft• mm• inch
DependenceThe units of the following parameters are changed:
• measured value (000)• input volume (045)• max. scale (046)• simulation value (066)
E+–
Pulscon LTCFunction group "linearisation" (04)
DO
CT
-009
4A06
/200
912
0782
37
6.4 Function "table no." (043)
Position of the value pair in the linearisation table.
DependenceUpdates "input level" (044), "input volume" (045).
6.5 Function "input level" (044)
You can enter the level for each point of the linearisation curve with this function. When the linearisation curve is entered semi-automatically, Pulscon LTC detects the level automatically.
User input:Level in "distance unit" (0C5).
E+–
E+–
Pulscon LTCFunction group "linearisation" (04)
DO
CT
-009
4A06
/200
912
0782
38
6.6 Function "input volume" (045)
Specify the volume for each point of the linearisation curve with this function.
User input:Volume in "customer unit" (042).
6.7 Function "max. scale" (046)
You can enter the end value of the measuring range with this function. This input is necessary if you selected "linear" or "horizontal cyl" in the "linearisation" (041) function.
6.8 Function "diameter vessel" (047)
Enter the tank diameter with this function. This entry is necessary if you selected "horizontal cyl" in the "linearisation" (041) function.
E+–
E+–
E+–
Pulscon LTCFunction group "extended calibr." (05)
DO
CT
-009
4A06
/200
912
0782
39
7 Function group "extended calibr." (05)
7.1 Function "selection" (050)
Select the function of the extended calibration.
Selection:• common (e. g. "level correction", "output damping", etc.)• mapping• delete mapping
7.2 Function "check distance" (051)
This function triggers the mapping of interference echoes. To do so, the measured distance must be compared with the actual distance to the product surface. The following options are available for selection:
Selection:• distance = ok• dist. too small• dist. too big• dist. unknown• manual• probe free
E+–
E+–
E+–
+
+
distance toosmall distance=ok
Pulscon LTCFunction group "extended calibr." (05)
DO
CT
-009
4A06
/200
912
0782
40
distance = ok
Use this function at part-covered probe. Choosing function "manual" or "probe free" at free probe.
• mapping is carried out up to the currently measured echo• The range to be suppressed is suggested in the "range of mapping" (052) functionAnyway, it is wise to carry out a mapping even in this case.
!Note!At free probe, the mapping should be confirmed with the choice "probe free".
dist. too small• At the moment, an interference is being evaluated• Therefore, a mapping is carried out including the presently measured echoes• The range to be suppressed is suggested in the "range of mapping" (052) function
dist. too big• This error cannot be remedied by interference echo mapping• Check the application parameters (002), (003), (004) and "probe length" (033)
dist. unknownIf the actual distance is not known, no mapping can be carried out.
manualA mapping is also possible by manual entry of the range to be suppressed. This entry is made in the "range of mapping" (052) function.
"Caution!The range of mapping must end 0.3 m (12") before the echo of the actual level.
7.3 Function "range of mapping" (052)
This function displays the suggested range of mapping. The reference point is always the reference point of the measurement (see page 2). This value can be edited by the operator.
For manual mapping, the default value is 0.3 m.
E+–
Pulscon LTCFunction group "extended calibr." (05)
DO
CT
-009
4A06
/200
912
0782
41
7.4 Function "start mapping" (053)
This function is used to start the interference echo mapping up to the distance given in "range of mapping" (052).
Selection:• off: no mapping is carried out• on: mapping is started
7.5 Function "pres. map dist." (054)
Displays the distance up to which a mapping has been recorded. A value of 0 indicates that no mapping was recorded so far.
7.6 Function "delete mapping" (055)
This function allows cancellation of the available mapping.
Selection:• no• yes
noThe available mapping is not cancelled and remains active.
yesAfter mapping is cancelled, the device skips to the "dist./meas.value" (008) display.
E+–
E+–
pres. map dist. (054)
E+–
Pulscon LTCFunction group "extended calibr." (05)
DO
CT
-009
4A06
/200
912
0782
42
7.7 Function "echo quality" (056)
The echo quality is the benchmark for measurement reliability. It describes the amount of reflected energy and depends primarily on the following conditions:
• Dielectric constant of the medium• probe type• Distance between sensor and productLow values increase the probability that the echo is lost through a change in measurement conditions, e. g. angels of repose or large measuring distance.
7.8 Function "offset" (057)
This function corrects the measured level by a constant value. The entered value is added to the measured level.
7.9 Function "output damping" (058)
Influences the time an output requires to react to a sudden level jump (63 % of steady state). A high value attenuates, for example, the influences of rapid changes on the measured variable.
User input:0 s ... 255 s
The default value depends on the selected application parameter "process cond." (004).
E+–
20 mA100 %
4 mA0 %
echo quality (056)
E+–
E+–
Pulscon LTCFunction group "extended calibr." (05)
DO
CT
-009
4A06
/200
912
0782
43
7.10 Function "upper block. dist" (059)
For rod and rope probes with lengths of up to 8 m, the upper blocking distance is preset to 0.2 m on delivery. For rope probes with lengths of more than 8 m, the upper blocking distance is preset to 2.5 % of the probe lengths.
For media DC > 7, the upper blocking distance for rod and rope probes can be reduced to 0.1 m, if the probe is mounted flush with the wall or in a nozzle of maximum 50 mm.
Blocking distance and measuring rangeAt the lower end of the probe there is no blocking distance but a transition region with reduced accuracy, see section "Maximum measured error".
1. Larger measurement range available on request.
2. The indicated blocking distances are preset. At media with DC > 7, the upper blocking distance UB can be reduced to 0.1 mm for rod and rope probes. The upper blocking distance UB can be entered manually.
!Note! Within the upper and lower blocking distance, a reliable measurement can not be guaranteed.
For stilling well applicationsThe upper blocking distance (UB) is preset to 100 mm when the "bypass/pipe" parameter has been selected in the "tank properties" (002) function.
Maximum measured errorTypical statements for reference conditions:DIN EN 61298-2, percentage of the span.
If the reference conditions are not met, the offset/zero arising from the mounting situation may be up to ± 12 mm. This additional offset/zero can be compensated for by entering a correction (function "offset" (057)) during commissioning.
E+–
LTC LN [m] UB [m]
min max min
Rope probe 1 351) 0.22)
6 mm rod probe 0.3 2 0.22)
16 mm rod probe 0.3 4 0.22)
Coax probe 0.3 4 0
Output: digital analogue
sum of non-linearity, non-repeatability and hysteresis
measuring range:- up to 10 m: ± 3 mm- > 10 m: ± 0.03 %for PA coated ropemeasuring range:- up to 5 m: ± 5 mm- > 5 m: ± 0.1 %
± 0.06 %
Offset/zero ± 4 mm ± 0.03 %
Pulscon LTCFunction group "extended calibr." (05)
DO
CT
-009
4A06
/200
912
0782
44
Differing from this, the following measuring error is present in the vicinity of the probe end:
!Note! Please re-enter the blocking distance in the function group "extended calibr." (05) function "upper block. dist" (059) when installing the device in a high nozzle: upper blocking distance (UB) = nozzle high (H) + 50 mm.
-80
-60
-40
-20
0
20
40
60
80
0 50 100 150 200 250 300
Rod probe and coax probe
Distance from probe end [mm]
Su
m o
f n
on
-lin
eari
ty, n
on
-rep
eata
bilit
yan
d h
yste
resis
[mm
]
DC = 2
DC > 7
-80
-60
-40
-20
0
20
40
60
80
0 50 100 150 200 250 300
Distance from probe end [mm]
Su
m o
f n
on
-lin
eari
ty, n
on
-rep
eata
bilit
yan
d h
yste
resis
[mm
]
Rope probe
DC > 7
UBH
50
After 3 s, the following message appears
E+–
Pulscon LTCFunction group "output" (06), - "profibus param." (06), PROFIBUS PA only
DO
CT
-009
4A06
/200
912
0782
45
8 Function group "output" (06), - "profibus param." (06), PROFIBUS PA only
8.1 Function "commun. address" (060), HART only
Enter the communication address for the instrument with this function.
• Standard: 0• Multidrop: 1 ... 15In multidrop mode, the standard output current is 4 mA. This can be changed in the "fixed cur. value" (064) function.
"Caution!This function is available for HART devices only!
8.2 Function "instrument addr." (060),PROFIBUS PA only
The PA bus address is displayed in this field. The address is set either directly on the instrument using DIP switches (see instrument operating instructions) or using a special Set Slave Address command via the bus, e. g. by the PACTwareTM.
"Caution!This function is available for PROFIBUS PA devices only!
8.3 Function "no. of preambels" (061), HART only
Enter the number of preambles for the HART protocol with this function. An increase in the value is advisable for "bad" lines with communications problems.
"Caution!This user input is available for HART devices only!
Display at HART instrument
E+–
Display at PROFIBUS PA instrument
E+–
E+–
E+–
E+–
Pulscon LTCFunction group "output" (06), - "profibus param." (06), PROFIBUS PA only
DO
CT
-009
4A06
/200
912
0782
46
8.4 Function "ident number" (061), PROFIBUS PA only
• manufacturer• profile
manufacturerSet to XXXX hex according to manufacturer (PNO registered).
profileSetting defined as in PROFIBUS PA Profile 3.0: 9700 hex - instrument with one AI block.
"Caution!This function is available for PROFIBUS PA devices only!
8.5 Function "low output limit" (062), HART only
The output of negative level values can be suppressed with this function.
Selection:• off: minimum output -10 % (3.8 mA for HART)• on: minimum output 0 % (4 mA for HART)
"Caution!This user input is available for HART devices only!
8.6 Function "set unit to bus" (062), PROFIBUS PA only
• confirmAfter confirming this function, the unit of the measured variable is taken over in the AI block (PV scale -> out scale). This function must always be executed after changing the unit.
"Caution!This function is available for PROFIBUS PA devices only!
E+–
E+–
OFF ON
E+–
Pulscon LTCFunction group "output" (06), - "profibus param." (06), PROFIBUS PA only
DO
CT
-009
4A06
/200
912
0782
47
8.7 Function "curr. output mode" (063), HART only
Use this function to specify the current output mode for HART devices.
Selection:• standard• curr. turn down• fixed current
standardThis selection displays the complete measuring range (0 % ... 100 %) across the full current interval (4 mA ... 20 mA).
curr. turn downThis selection only displays a part of the measuring range across the full current interval (4 mA ... 20 mA). This range is specified using the "4mA value" (068) and "20mA value" (069) functions.
fixed currentSelecting this outputs a fixed current. The measured value is only transmitted using the HART signal. The current output value is set using the "fixed cur. value" (064) function.
"Caution!This selection is available for HART devices only!
8.8 Function "out value" (063), PROFIBUS PA only
This displays the AI block output.
"Caution!This function is available for PROFIBUS PA devices only!
E+–
[mA]20
[mA]20
4
100 [%]0
4
100 [%]0
fixed current
curr. turn down
standard
E+–
Pulscon LTCFunction group "output" (06), - "profibus param." (06), PROFIBUS PA only
DO
CT
-009
4A06
/200
912
0782
48
8.9 Function "fixed cur. value" (064), HART only
Set the fixed current value with this function. This data is necessary if you have selected the "fixed current" option in the "curr. output mode" (063) function.
User input:3.8 mA ... 20.5 mA
"Caution!This user input is available for HART devices only!
8.10 Function "out status" (064), PROFIBUS PA only
Displays the current output status (for value, see operating instructions of relevant instrument).
"Caution!This function is available for PROFIBUS PA devices only!
E+–
E+–
Pulscon LTCFunction group "output" (06), - "profibus param." (06), PROFIBUS PA only
DO
CT
-009
4A06
/200
912
0782
49
8.11 Function "simulation" (065)
If necessary, linearisation, the output signal and the current output can be tested with the simulation function. You have the following simulation options:
Selection:• sim. off• sim. level• sim. volume• sim. current (HART only)
sim. offSimulation is switched off.
sim. levelEnter the level value in "simulation value" (066).
The functions
• measured value (000)• measured level (0A6)• output current (067) - only with HART instruments!follow the entered values.
sim. volumeEnter the volume value in "simulation value" (066).
The functions
• measured value (000)• output current (067) - only with HART instruments!follow the entered values.
sim. current (HART only)Enter the current value in "simulation value" (066).
The function
• output current (067) - only with HART instruments!follows the entered values.
E+–
sim. current(HART only)
sim. volume
sim. level
E+–
Pulscon LTCFunction group "output" (06), - "profibus param." (06), PROFIBUS PA only
DO
CT
-009
4A06
/200
912
0782
50
8.12 Function "simulation value" (066)
8.13 Function "output current" (067), HART only
Displays the output current in mA.
"Caution!This function is available for HART devices only!
8.14 Function "2nd cyclic value" (067), PROFIBUS PA only
Selects the second cyclical value.
• height/dist.Pulscon LTC always transmits the distance as the second cyclical value.
"Caution!This function is available for PROFIBUS PA devices only!
8.15 Function "4mA value" (068), HART only
In this function, enter the level (or volume, weight) at which the output current should be 4 mA. This entry is only required if you selected the "current turn down" option in the "curr. output mode" (063) function.
"Caution!This function is available for HART devices only!
After selecting the "sim. level" option in the "simulation" (065) function, the following message appears in the display: you can enter the level.E+–
After selecting the "sim. volume" option in the "simulation" (065) function, the following message appears in the display: you can enter the volume.E+–
After selecting the "sim. current" option in the "simulation" (065) function, the following message appears in the display: Enter the output current (only for HART instruments).E+–
E+–
E+–
E+–
Pulscon LTCFunction group "output" (06), - "profibus param." (06), PROFIBUS PA only
DO
CT
-009
4A06
/200
912
0782
51
8.16 Function "select v0h0" (068), PROFIBUS PA only
Selects the value displayed in "measured value" (000).
Selection:• measured value• display value
measured valueThe configured measured value is displayed in the "measured value" (000) function.
display valueThe value in "display value" (069) is displayed in the "measured value" (000) function.
"Caution!This function is available for PROFIBUS PA devices only!
8.17 Function "20mA value" (069), HART only
In this function, enter the level (or volume, weight) at which the output current should be 20 mA. This entry is only required if you have selected the "current turn down" option in the "curr. output mode" (063) function.
"Caution!This function is available for HART devices only!
8.18 Function "display value" (069), PROFIBUS PA only
This field can be set externally, e. g. from a PLC. The value is then displayed as the main measured variable in the display by selecting the "select v0h0" (068) = "display value" function.
"Caution!This function is available for PROFIBUS PA devices only!
E+–
E+–
E+–
Pulscon LTCFunction group "envelope curve" (0E)
DO
CT
-009
4A06
/200
912
0782
52
9 Function group "envelope curve" (0E)
9.1 Function "plot settings" (0E1)
Here you can select which information is shown on the display:
• envelope curve• subtracted signal• mapping
9.2 Function "recording curve" (0E2)
This function determines whether the envelope curve is read as
• single curve or• cyclic
!Note! If the cyclical envelope curve is active in the display, the measured variable is refreshed in a slower cycle time. It is therefore recommended to exit the envelope curve display after optimising the measuring point.
E+–
E+–
E+–
Pulscon LTCFunction group "envelope curve" (0E)
DO
CT
-009
4A06
/200
912
0782
53
9.3 Function "envelope curve display" (0E3)
You can obtain the following information from the envelope curve display in this function:
Navigation in the envelope curve displayUsing navigation, the envelope curve can be scaled horizontally and vertically and shifted to the left or the right. The active navigation mode is indicated by a symbol in the top left hand corner of the display.
minimum distanceof the plot
maximum distanceof the plot
distance ofevaluated echo
evaluated echois marked
quality ofevaluated echo empty calibr.
empty calibr.
empty calibr.
envelope curve
substracted signal
mapping
level echo
level echo
full calibr.
full calibr.
probe length
probe length
…
Move mode:
- m
-
oved to the left
moved to the right
Horizontal zoom mode:
- h
-
orizontal zoom in
horizontal zoom out
Vertical zoom mode:
- vertical zoom (4 steps)
Pulscon LTCFunction group "envelope curve" (0E)
DO
CT
-009
4A06
/200
912
0782
54
Horizontal zoom mode
Press O or S, to switch to the envelope curve navigation. You are then in horizontal zoom mode. Either or is displayed.
You now have the following options:
• O increases the horizontal scale.• S decreases the horizontal scale.
Move modeThen press F, to switch to move mode. Either or is displayed.
You now have the following options:
• O shifts the curve to the right.• S shifts the curve to the left.
Vertical zoom modePress F, once more to switch to vertical zoom mode. is displayed.
You now have the following options:
• O increases the vertical scale.• S decreases the vertical scale.The display icon shows the current zoom factor ( to ).
Exiting the navigation• Press F again to run through the different modes of the envelope curve navigation.• Press O and S to exit the navigation. The set increases and shifts are retained.
Only when you reactivate the "recording curve"(0E2) function does the Pulscon use the standard display again.
OS
OS
OS
After 3 s, the following message appears
E+–
Pulscon LTCFunction group "display" (09)
DO
CT
-009
4A06
/200
912
0782
55
10 Function group "display" (09)
10.1 Function "language" (092)
Selects the display language.
Selection:• English• Deutsch• Français• Español• Italiano• Nederlands• Katakana (japanese)
DependenceAll texts are changed.
"Caution!This function is not visualised in PACTwareTM!
10.2 Function "back to home" (093)
If no entry is made using the display during the specified time period, the display returns to the measured value display.
9999 s means that there is no return.
User input:3 s ... 9999 s
"Caution!This function is not visualised in PACTwareTM!
E+–
E+–
E+–
Pulscon LTCFunction group "display" (09)
DO
CT
-009
4A06
/200
912
0782
56
10.3 Function "format display" (094)
Selects the display format.
Selection:• decimal• ft-in-1/16"
decimalThe measured value is given in decimal form in the display (e. g. 10.70 %).
ft-in-1/16"The measured value is given in the display in this format (e. g. 5'05-14/16"). This option is only possible for "distance unit" (0C5) - "ft" and "in"!
"Caution!This function is not visualised in PACTwareTM!
10.4 Function "no.of decimals" (095)
Selection:• x• x.x• x.xx• x.xxx
10.5 Function "sep. character" (096)
Selection:• .• ,
.The decimal place is separated by a point.
,The decimal place is separated by a comma.
E+–
E+–
E+–
Pulscon LTCFunction group "display" (09)
DO
CT
-009
4A06
/200
912
0782
57
10.6 Function "display test" (097)
All display pixels are switched on. If the whole LCD is dark, it is working correctly.
E+–
After 3 s, the following message appears
E+–
Pulscon LTCFunction group "diagnostics" (0A)
DO
CT
-009
4A06
/200
912
0782
58
11 Function group "diagnostics" (0A)
In the "diagnostics" function group, you can display and confirm error messages.
Type of errorErrors that occur during commissioning or measuring are displayed immediately on the local display. If two or more system or process errors occur, the error with the highest priority is the one shown on the display.
The measuring system distinguishes between two types of error:
• A (Alarm):Instrument goes into a defined state (e. g. MAX)Indicated by a constant symbol.(For a description of the codes, see page 72)
• W (Warning):Instrument continue measuring, error message is displayed.Indicated by a flashing symbol.(For a description of the codes, see page 72)
• E (Alarm/Warning):Configurable (e. g. loss of echo, level within the safety distance)Indicated by a constant/flashing symbol.(For a description of the codes, see page 72)
Error messagesError messages appear as four lines of plain text on the display. In addition, a unique error code is also output. A description of the error codes is given on page 72.
• The "diagnostics" (0A) function group can display current errors as well as the last errors that occurred.
• If several current errors occur, use O or S to page through the error messages.• The last occurring error can be deleted in the "diagnostics" (0A) function group
with the function "clear last error" (0A2).
E+–
Pulscon LTCFunction group "diagnostics" (0A)
DO
CT
-009
4A06
/200
912
0782
59
11.1 Function "present error" (0A0)
The present error is shown using this function.
11.2 Function "previous error" (0A1)
The last error presented is shown with this function.
11.3 Function "clear last error" (0A2)
Selection:• keep• erase
E+–
E+–
E+–
Pulscon LTCFunction group "diagnostics" (0A)
DO
CT
-009
4A06
/200
912
0782
60
11.4 Function "reset" (0A3)
"Caution!A reset sets the instrument back to the factory settings. This can lead to an impairment of the measurement. Generally, you should perform a basic setup again following a reset.
A reset is only necessary:
• if the instrument no longer functions• if the instrument must be moved from one measuring point to another• if the instrument is being de-installed/put into storage/installed
Entry ("reset" (0A3)):• 333 = customer parameters (HART)• 33333 = customer parameters (PROFIBUS PA)333 = reset customer parameters for HART33333 = reset customer parameters for PROFIBUS PAThis reset is recommended whenever an instrument with an unknown "history" is to be used in an application:
• The Pulscon LTC is reset to the default values.• The customer specific tank map is not deleted.• A linearisation is switched to "linear" although the table values are retained. The
table can be reactivated in the "linearisation" (04) function group.List of functions that are affected by a reset:
The mapping can also be deleted in the "cust. tank map" (055) function of the "extended calibr." (05) function group.
A complete "basic setup" (00) must be activated.
E+–
• tank properties (002)• medium cond. (003)• process proper. (004)• empty calibr. (005)• full calibr. (006)• output on alarm (010)• output on alarm (011)• outp. echo loss (012)• ramp %span/min (013)• delay time (014)• safety distance (015)• in safety dist. (016)• overspill protection (018)• end of probe (030)• level/ullage (040)• linearisation (041)• customer unit (042)
• max. scale (046)• diameter vessel (047)• check distance (051)• range of mapping (052)• start mapping (053)• offset (057)• output damping (058)• low output limit (062)• curr. output mode (063)• fixed cur. value (064)• 4mA value (068)• language (092)• back to home (093)• format display (094)• no of decimals (095)• sep. character (096)• unlock parameter (0A4)
Pulscon LTCFunction group "diagnostics" (0A)
DO
CT
-009
4A06
/200
912
0782
61
11.5 Function "unlock parameter" (0A4)
Set-up can be locked and unlocked with this function.
11.5.1 Locking of the configuration mode
The Pulscon LTC can be protected in two ways against unauthorised changing of instrument data, numerical values or factory settings:
"unlock parameter" (0A4):A value <> 100 for HART (e. g. 99) or <> 2457 for PROFIBUS PA (e. g. 2456) must be entered in "unlock parameter" (0A4) in the "diagnostics" (0A) function group. The lock is shown on the display by the symbol and can be released again either via the display or by communication.
Hardware lock:The instrument is locked by pressing the O and S and F keys at the same time. The lock is shown on the display by the symbol and can only be unlocked again via the display by pressing the O and S and F keys at the same time again. It is not possible to unlock the hardware by communication.
All parameters can be displayed even if the instrument is locked.
E+–
O and S and F press simultaneous
The LOCK_SYMBOL appears on the LCD.
E+–
Pulscon LTCFunction group "diagnostics" (0A)
DO
CT
-009
4A06
/200
912
0782
62
11.5.2 Unlocking of configuration mode
If an attempt is made to change parameters when the instrument is locked, the user is automatically requested to unlock the instrument:
"unlock parameter" (0A4):By entering the unlock parameter (on the display or via communication)
100 = for HART devices2457 = for PROFIBUS PA devices
the Pulscon LTC is released for operation.
Hardware lock:After pressing the O and S and F keys at the same time, the user is asked to enter the unlock parameter
100 = for HART devices2457 = for PROFIBUS PA devices.
"Caution!Changing certain parameters such as all sensor characteristics, for example, influences numerous functions of the entire measuring system, particularly measuring accuracy. There is no need to change these parameters under normal circumstances and consequently, they are protected by a special code known only to the P+F service organisation. Please contact Pepperl+Fuchs if you have any questions.
11.6 Function "measured dist." (0A5)
Display of measured distance in the selected "distance unit" (0C5).
O and S and F press simultaneous
Please enter unlock code and confirm with F.
E+–
E+–
Pulscon LTCFunction group "diagnostics" (0A)
DO
CT
-009
4A06
/200
912
0782
63
11.7 Function "measured level" (0A6)
Display of measured level in the selected "distance unit" (0C5).
11.8 Function "detection window" (0A7) (from Software 01.04.00)
Is used to switch the detection window on and off and to reset an existing detection window. If this function is switched on, a window is defined surrounding the current level echo (typical width: 1 m ... 2.5 m; depending on the application parameters). The window always moves together with a rising a falling echo.
Echos beyond the limits of the window are ignored for a certain time.
Selection:• off• on• reset
After selection of this option, the current window is reset, the level echo is looked for in the complete measuring range and a new window is defined surrounding the current level echo.
E+–
20mA100 %
4 mA0 %
measureddist.(0A5)
measured level (0A6)
E+–
Pulscon LTCFunction group "diagnostics" (0A)
DO
CT
-009
4A06
/200
912
0782
64
11.9 Function "application par." (0A8)
Displays whether or not one of the settings dependent on the "tank shape" (002), "medium property" (003) and "process cond." (004) application parameters has been changed or not.
If, for example, the "output damping" (058) is changed, the "application par." shows "modified".
Selection:• not modified• modified
E+–
After 3 s, the following message appears
E+–
Pulscon LTCFunction group "system parameters" (0C)
DO
CT
-009
4A06
/200
912
0782
65
12 Function group "system parameters" (0C)
12.1 Function "tag no." (0C0)
You can define the tag number with this function.
User input:• 16 alphanumeric characters for HART instruments
(8 using the HART universal command)• 32 alphanumeric characteristics for PROFIBUS PA instruments
12.2 Function "profile version" (0C1), PROFIBUS PA only
The PROFIBUS PA profile version is shown using this function (Profile 3.0).
"Caution!This function is available for PROFIBUS PA devices only!
12.3 Function "protocol+sw-no." (0C2)
This function shows the protocol and the hardware and software version: Vxx.yy.zz.prot.
Display:xx: hw-versionyy: sw-versionzz: sw-revisionprot: protocoll type (e. g. HART)
12.4 Function "serial no." (0C4)
This function displays the instrument serial number.
E+–
E+–
E+–
E+–
E+–
Pulscon LTCFunction group "system parameters" (0C)
DO
CT
-009
4A06
/200
912
0782
66
12.5 Function "distance unit" (0C5)
You can select the basic distance unit with this function.
Selection:• m• ft• mm• inch
Dependencem, mm: "format display" (094) can only be "decimal".
The units are changed for the following parameters:
• empty calibr. (005)• full calibr. (006)• safety distance (015)• input level (044)• diameter vessel (047)• range of mapping (052)• cust. tank map (055)• offset (057)• simulation value (066)• measured dist. (0A5)• measured level(0A6)
E+–
Pulscon LTCFunction group "system parameters" (0C)
DO
CT
-009
4A06
/200
912
0782
67
12.6 Function "download mode" (0C8)
This parameter defines which values are written to the instrument during a PACTwareTM download.
Selection:• parameter only• param+cust.map• mapping only
!Note! This parameter must not be described explicitly in PACTwareTM. The various possibilities can be selected from the download dialog.
E+–
After 3 s, the following message appears
E+–
Pulscon LTCFunction group "service" (0D)
DO
CT
-009
4A06
/200
912
0782
68
13 Function group "service" (0D)
You can find a detailed description of the "Service" function group as well as a detailed overview of the function menu in the service manual for Pulscon LTC.
Pulscon LTCEnvelope curve (echo curve)
DO
CT
-009
4A06
/200
912
0782
69
14 Envelope curve (echo curve)
14.1 Envelope curve with the PACTwareTM
Signal analysis via envelope curve (echo curve)
See page 52 ff for the envelope curve in the local display.
Pulscon LTCTrouble-shooting
DO
CT
-009
4A06
/200
912
0782
70
15 Trouble-shooting
If you have followed the instructions in this operating manual, the Pulscon LTC should work correctly. If this is not the case, Pulscon LTC has facilities for analysing and correcting errors.
You can find a structured approach for locating errors on page 71 or in the appropriate instrument operating manual.
Pulscon LTCTrouble-shooting
DO
CT
-009
4A06
/200
912
0782
71
15.1 Trouble-shooting instructions
Instrument doesnot respond
Check voltage andcompare it with thespecifications on thenameplate.
Connect thecorrect voltage Instrument works? Ready
Check the polarityof the voltage.
Check power connectionto electronic board
Correct the polarity
Connect plug
Instrument works?
Instrument works?
Ready
Ready
Values on displayinvissible
ok
ok
ok
Yes
Yes
Yes
No
No
No
No
Not ok
Not ok
Not ok
Check plug contactof the display.
Connect the plugcorrectly
Correct configuration
Display works? Ready
Ready
Yes
ok
No
Not ok
Yes
No
ok
Output current between3.6 … 22mA?
Contrast: F O+
The display is possibly defective.Yes
Output current< 3.6 mA ? (2 wire)< 2.4 mA ? (4 wire)
No
Check cabling Correct thecabling Current is ok? Ready
Yes
No
Possibly defective electronics
HARTcommunicationdoes notfunction
Is the communicationresistor installedaccording to theOM?
Install the fuse(see the OM) Communication ok? Ready
Ready
ok
Yes
Yes
No
No
Connect theHART modem(see the OM)
Communication ok? Ready
Set the switchcorrectly Communication ok Ready
Ready
ok
ok
ok
Yes
No
Yes
Yes
No
No
ok
Not ok
Not ok
Not ok
Not ok
Not ok
Not ok
?
Is the switch on theHART modem forselecting HARTin the correct position?
Is the HART modemconnected accordingto the OM?
Communicationvia Service adapterdoes not function
Instrumentmeasuresincorrectly
Check configurationof COM port on PC
Check basic setup
Proceed accordingto sectionTrouble shooting in OM
Repeatbasic setup
Not ok
Yes
Yes
Yes
Yes
Yes
CommunicationPA does notfunction
Check cabling +terminator
EMC interference?
ok
Correct cabling +terminator
Not ok
Check screening(see BA sectionConnection)
Yes
Communication ok?
Communication ok?
Measurement ok?
ReadyYes
No
Communication ok? ReadyYes
No
Contact Pepperl+Fuchs service.
Contact Pepperl+Fuchs service.
Contact Pepperl+Fuchs service.
Contact Pepperl+Fuchs service.
Contact Pepperl+Fuchs service.
Pulscon LTCTrouble-shooting
DO
CT
-009
4A06
/200
912
0782
72
15.2 System error messages
Code Description Possible cause Remedy
A102 checksum errorgeneral reset & new calibr. required
device has been powered off before data could be stored; EMC problem; E2PROM defect
resetavoid EMC problem;if alarm prevails after reset, exchange electronics
W103 initialising - please wait E2PROM storage not yet finished wait some seconds; if warning prevails, exchange electronics
A106 downloading please wait processing data download wait until warning disappears
A110 checksum errorgeneral reset & new calibr. required.
device has been powered off before data could be stored;EMC problem; E2PROM defect
resetavoid EMC problem;if alarm prevails after reset, exchange electronics
A111 electronics defect RAM defective resetif alarm prevails after reset, exchange electronics
A113 electronics defect ROM defective resetif alarm prevails after reset, exchange electronics
A114 electronics defect E2PROM defective resetif alarm prevails after reset, exchange electronics
A115 electronics defect general hardware problem resetif alarm prevails after reset, exchange electronics
A116 download errorrepeat download
checksum of stored data not correct restart download of data
A121 electronics defect no factory calibration existant; E2PROM defective
contact service
W153 initialising - please wait initialisation of electronics wait some seconds; if warning prevails, power off device and power on again
A160 checksum errorgeneral reset & new calibr. required.
device has been powered off before data could be stored; EMC problem; E2PROM defect
resetavoid EMC problem;if alarm prevails after reset, exchange electronics
A164 electronics defect hardware problem resetif alarm prevails after reset, exchange electronics
A171 electronics defect hardware problem resetif alarm prevails after reset, exchange electronics
A221 probe pulse deviation from average values
HF module or cable between HF module and electronics defective
check contacts on HF moduleif fault cannot be eliminated: replace HF module
A241 broken probe broken probe or value for probe length is too short
check the probe length in 033, check the probe itself, if the probe is broken, change the probe, or change to a non contact system
broken probe detection is activated, without carry out the mapping before
deactivate broken probe detection; carry out mapping; activate broken probe detection
A251 feedthrough lost contact in the process feedthrough
replace process feedtrough
A261 HF cable defective HF cable defective or HF connector removed
check HF connector, replace cable if defective
W275 offset too high temperature at the electronics too high or HF module defective
check temperature, replace HF module if defective
W512 recording of mapping please wait mapping active wait some seconds until alarm disappears
W601 linearisation ch1 curve not monotone linearisation not monotonously increasing
correct linearisation table
W611 less than 2 linearisation points for channel 1
number of entered linearisation points < 2
correct linearisation table
W621 simulation ch. 1 on simulation mode is active switch off simulation mode
E641 no usable echochannel 1check calibr.
echo lost due to application conditions of built up on antenna
check installation; clean probe (see operating instructions)
W650 signal/noise ratio too low or no echo noise on signal to high eliminate electromagnetic interference
E651 level in safety distance - risk of overspill
level in safety distance alarm will disappear as soon as level leaves safety distance
A671 linearisation ch1 not complete, not usable
linearisation table is in edit mode activate linearisation table
W681 current ch1 out of range current out of range(3.8 mA ... 21.5 mA)
check calibration and linearisation
Pulscon LTCTrouble-shooting
DO
CT
-009
4A06
/200
912
0782
73
15.3 Application errors
Error Output Possible cause Remedy
A warning or alarm has occurred.
Depending on the configuration see table oferror messages (see page 72)
1. see table of error messages (see page 72)
Measured value (00) is incorrect
"measured distance" (008) OK?
yes → 1. check "empty calibr." (005) and"full calibr." (006)
2. check linearisation:→ "level/ullage" (040)→ "max. scale" (046)→ "diameter vessel" (047)→ check table
no ↓An interference echo may have been evaluated.
yes → 1. carry out tank mapping→ basic setup
No change off measured value on filling/emptying
interference echo from installations, nozzle or extension on the probe
1. carry out tank mapping→ basic setup
2. if necessary, clean probe
3. if necessary, select better mounting position
E 641 (loss of echo) after turn on the power supply
If the instrument is configured to HOLD by loss of echo the output is set to any value/current.
noise level during the initialisation phase to high.
repeat once more "empty calibr." (005).Caution! Before conformation change with O or S to the edit mode.
Device displays a level when the tank is empty.
incorrect probe length
1. carry out automatic probe length detection when the tank is empty.
2. carry out mapping over entire probe when the tank is empty (probe free!).
Measured value incorrect (slope error in the entire measuring range)
tank properties incorrect.
medium properties incorrect.
LN < 4 m and "aluminium tank" tank properties selected→ calibration not possible→ selection→ select standard→ thresholds too high
Select lower medium properties.
20 mA/100 %F m/ft
E m/ft4 mA/0 % t →
D m
/ft (
008)
actual
expected
20 mA/100 %
4 mA/0 % t →
actual
expected
20 mA/100 %
4 mA/0 % t →
actual
expected
20 mA/100 %
4 mA/0 % t →
2.) actual
1.) actual
expected
Pulscon LTCTrouble-shooting
DO
CT
-009
4A06
/200
912
0782
74
15.4 Software history
Software version/date Software modifications Documentation
HART PA HART, PA
V 01.02.00/04.2002 Original software.Operated via:- PACTwareTM
- HART communicator 375 with Rev. 1, DD 1.
BA242O/00/en/06.09 BA243O/00/en/06.09 BA245O/00/en/06.09
V 01.02.02/08.2003 - Function group: envelope curve display
- Katakana (Japanese)- Current turn down (HART
only)- the customer tank map
can be editedOperated via:- PACTwareTM
- HART communicator 375 with Rev. 1, DD 1.
— — —
V 01.02.04/07.2004 - "mapping" function improved
- Specification of the measuring accuracy at the end of probe
BA242O/00/en/06.09 BA243O/00/en/06.09 BA245O/00/en/06.09
V 01.02.06/01.2005 "echo lost" function improved — — —
V 01.04.00/03.2006 - "detection window" function
- Description of instrument function
- Operating menu extended
BA242O/00/en/06.09 BA243O/00/en/06.09 BA245O/00/en/06.09
Pulscon LTCIndex function menu
DO
CT
-009
4A06
/200
912
0782
75
Function group00 = basic setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
01 = safety settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
03 = length adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . 2904 = linearisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
05 = extended calibr. . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
06 = output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4506 = PROFIBUS Param. (PROFIBUS PA only) . . . . . . . 45
09 = display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
0A = diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 580C = system parameter . . . . . . . . . . . . . . . . . . . . . . . . . 65
0D = service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
0E = envelope curve. . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Function000 = measured value . . . . . . . . . . . . . . . . . . . . . . . . . . 13
002 = tank properties . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
003 = medium property . . . . . . . . . . . . . . . . . . . . . . . . . 14004 = process propert. . . . . . . . . . . . . . . . . . . . . . . . . . . 15
005 = empty calibr. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
006 = full calibr. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18008 = display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 21
010 = output on alarm . . . . . . . . . . . . . . . . . . . . . . . . . . 22
011 = output on alarm (HART only) . . . . . . . . . . . . . . . . 24012 = outp. echo loss . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
013 = ramp %span/min . . . . . . . . . . . . . . . . . . . . . . . . . 25
014 = delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26015 = safety distance . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
016 = in safety dist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
017 = ackn. alarm. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28018 = overspill prot. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
019 = broken probe det . . . . . . . . . . . . . . . . . . . . . . . . . 28
030 = end of probe. . . . . . . . . . . . . . . . . . . . . . . . . . 15, 29
031 = probe length. . . . . . . . . . . . . . . . . . . . . . . . . . 16, 29032 = probe. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 29
033 = probe length. . . . . . . . . . . . . . . . . . . . . . . . . . 16, 30
034 = determine length. . . . . . . . . . . . . . . . . . . . . . . 17, 30040 = level/ullage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
041 = linearisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
042 = customer unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36043 = table no. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
044 = input level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
045 = input volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38046 = max. scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
047 = diameter vessel . . . . . . . . . . . . . . . . . . . . . . . . . . 38
050 = Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39051 = check distance . . . . . . . . . . . . . . . . . . . . . . . . 19, 39
052 = range of mapping . . . . . . . . . . . . . . . . . . . . . . 20, 40
053 = start mapping . . . . . . . . . . . . . . . . . . . . . . . . . 20, 41
054 = pres. Map dist. . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
055 = delete mapping. . . . . . . . . . . . . . . . . . . . . . . . . . . 41056 = echo quality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
057 = offset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
058 = output damping . . . . . . . . . . . . . . . . . . . . . . . . . . 42059 = upper block.dist . . . . . . . . . . . . . . . . . . . . . . . . . . 43
060 = commun.address (HART only) . . . . . . . . . . . . . . 45
060 = instrument addr. (PROFIBUS PA only) . . . . . . . . 45061 = no. of preambels (HART only) . . . . . . . . . . . . . . . 45
061 = ident number (PROFIBUS PA only) . . . . . . . . . . 46
062 = low output limit (HART only) . . . . . . . . . . . . . . . . 46062 = set unit to bus (PROFIBUS PA only) . . . . . . . . . . 46
063 = curr. output mode (HART only) . . . . . . . . . . . . . . 47
063 = out value (PROFIBUS PA only). . . . . . . . . . . . . . . 47064 = fixed cur. value (HART only) . . . . . . . . . . . . . . . . 48
064 = out status (PROFIBUS PA only) . . . . . . . . . . . . . 48
065 = simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49066 = simulation value. . . . . . . . . . . . . . . . . . . . . . . . . . 50
067 = output current (HART only) . . . . . . . . . . . . . . . . . 50
067 = 2nd cyclic value (PROFIBUS PA only) . . . . . . . . 50068 = 4mA value (HART only). . . . . . . . . . . . . . . . . . . . 50
068 = select v0h0 (PROFIBUS PA only) . . . . . . . . . . . . 51
069 = 20mA value (HART only). . . . . . . . . . . . . . . . . . . 51069 = display value (PROFIBUS PA only). . . . . . . . . . . 51
092 = language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
093 = back to home. . . . . . . . . . . . . . . . . . . . . . . . . . . . 55094 = format display . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
095 = no.of decimals . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
096 = sep. character . . . . . . . . . . . . . . . . . . . . . . . . . . . 56097 = display test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
0A0 = present error . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
0A1 = previous error . . . . . . . . . . . . . . . . . . . . . . . . . . . 590A2 = clear last error . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
0A3 = reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
0A4 = unlock parameter . . . . . . . . . . . . . . . . . . . . . . . . 61
0A5 = measured dist.. . . . . . . . . . . . . . . . . . . . . . . . . . . 620A6 = measured level . . . . . . . . . . . . . . . . . . . . . . . . . . 63
0A7 = detection window. . . . . . . . . . . . . . . . . . . . . . . . . . 63
0A8 = application par. . . . . . . . . . . . . . . . . . . . . . . . . . . 640C0 = tag no. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
0C1 = profile version (PROFIBUS PA only) . . . . . . . . . 65
0C2 = protocoll+sw-no. . . . . . . . . . . . . . . . . . . . . . . . . . 650C4 = serial no. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
0C5 = distance unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
0C8 = download mode. . . . . . . . . . . . . . . . . . . . . . . . . . 670E1 = plot settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
0E2 = recording curve . . . . . . . . . . . . . . . . . . . . . . . . . . 52
0E3 = envelope curve display . . . . . . . . . . . . . . . . . . . . 53Index function menu
Pulscon LTCNotes
DO
CT
-009
4A06
/200
912
0782
76
Pulscon LTCNotes
DO
CT
-009
4A06
/200
912
0782
77
Pulscon LTCNotes
DO
CT
-009
4A06
/200
912
0782
78
With regard to the supply of products, the current issue of the following document is applicable: The General Terms of
Delivery for Products and Services of the Electrical Industry, published by the Central Association of the
"Elektrotechnik und Elektroindustrie (ZVEI) e.V." including the supplementary clause: "Erweiterter Eigentumsvorbehalt".
We at Pepperl+Fuchs recognise a duty to make a contribution to the future,
For this reason, this printed matter is produced on paper bleached without the use of chlorine.
Subject to modificationsCopyright PEPPERL+FUCHS • Printed in Germany
www.pepperl-fuchs.com
Worldwide HeadquartersPepperl+Fuchs GmbH68307 Mannheim · GermanyTel. +49 621 776-0E-mail: [email protected]
USA HeadquartersPepperl+Fuchs Inc.Twinsburg, Ohio 44087 · USATel. +1 330 4253555E-mail: [email protected]
Asia Pacific HeadquartersPepperl+Fuchs Pte Ltd.Company Registration No. 199003130ESingapore 139942Tel. +65 67799091E-mail: [email protected]
PROCESS AUTOMATION – PROTECTING YOUR PROCESS
BA245O/98/en/06.09
FM7.0
DOCT-0094A 120782
06/2009
52013052