awe mkv k04 kit

8/14/2019 AWE MKV K04 Kit

1/4

Congratulations on your purchase of the AWE Tuning K04 Turbo Kit for your Mk5 2.0T.

Please note that a full turbo back performance exhaust is required for safe operation of this

kit. We highly recommend 2.5 diameter exhaust systems for optimum power and boostpressure production. 3 diameter exhaust systems can negatively impact the turbo spoolcharacteristics, resulting in slow boost production and also throttle/boost cut upon fullboost production.

Installation of this turbo kit can be completed on jack stands or ramps. Never work under a vehicle onlysupported by a jack. If you do not feel comfortable installing this system yourself, contact a local pro-fessional for installation.

05-> VW GTI/GLIK04 Turbo Kit

Copyright 2008, AWE Tuning. No part of this document may be reused or duplicated without the express permission of AWE Tuning/Secor Ltd. All rights reserved. Page 1 of 3

Installation of this turbo kit is very straight forward.

1. Before installing the AWE Tuning K04 turbo, remove the

factory installed outlet silencer by removing the three boltsand then pulling the silencer free (see Figure 1).

2. After silencer removal, place rubber o-ring aside for re-assembly (see Figure 2).

Figure 2

Figure 1

Parts list:

1 A.W.E. Tuning K041 A.W.E. Tuning turbo outlet

1 A.W.E. Tuning DV relocation housing1 Manifold to head gasket1 Turbo to down pipe gasket1 Oil return line gasket1 PCV line to turbo gasket4 Oil line crush washer

8 Coolant line crush washer4 Turbo to down pipe stud

4 Turbo to down pipe nut5 Manifold to head nut3 M6 Allen bolts for compressor outlet4 30-42mm hose clamp2 2.25 T-bolt clamp2 1 ID silicone coupler1 2 ID silicone coupler


2/4


3. Assembly of the new turbo outlet/diverter valve relocationkit is easier done once the K04 turbo is installed in vehicle.See Figure 3 for sample assembly picture out of vehicle.Use the enclosed hex head bolts to fasten the turbo outlet tothe turbo, reusing the o-ring removed in Step 2.Use the enclosed 1 silicone couplers and 30-42mm hose

clamps to fasten the diverter valve relocation adapter to theturbo and turbo outlet.

4. Consult factory manual for K03 turbo removal. Removalof driver side axle greatly eases removal and install of K04.

5. After install of K04 turbo, ensure there is proper clearancearound all hoses and A/C lines.

6. The stock turbo compressor outlet pipe needs to be modi-fied to meet up with the AWE Tuning K04 turbo outlet. Care-fully cut the metal clamp and remove the OEM silicone cou-pler shown at arrow in Figure 4.

7. Using a hack saw, cut the end off the outlet pipe just tothe outside of the second bead roll (at arrow in Figure 5).Cut the pipe so that it matches the pipe pictured in Figure 6.

8. Attach the enclosed 2 silicone coupler to the cut end ofthe outlet pipe, using the enclosed t-bolt clamp. Use the re-

maining t-bolt clamp to fasten the coupler to the AWE Tuningturbo outlet (installed on the K04 turbo in Step 3).

9. All new exhaust gaskets, coolant/oil crush washers, andPCV gaskets are included with the kit. Also included are newturbo to downpipe studs and nuts.

Figure 4

Figure 5

Figure 6

Figure 3


3/4

Any questions of comments, please do not hesitate to contact us:

1-888-565-2257 AWE-Tuning.com [email protected]


10. After the K04 turbocharger has been bolted to cylinder head and the oil feed and return lines havebeen reconnected, replace oil filter and refill engine with fresh oil. Because of extreme oil operatingtemps, use synthetic engine oil only.

11. Before restarting the engine for the first time, the engine, oil lines and turbocharger must beprimed with oil. To perform this procedure, first locate the engine ECU and disconnect the multipin con-nectors from the ECU. Next turn the ignition to the RUN position and crank the starter motor in several4-5 second bursts. (Your oil pump will circulate oil, however no spark or fuel will be introduced into theengine.) Next turn the ignition key to the OFF/LOCK position and reconnect the multipin connectors tothe ECU. Specific GIAC software is to be used with this kit, and it should be installed at thispoint.After initial start-up, allow the vehicle to idle for several minutes. Do not rev the motor at this time.Shut down the engine and check the oil level. Top off if necessary.

OPERATION

K04 users should always bring their vehicle to a complete stop and allow the engine to idle prior toshutting down the engine. Recommended idle times vary from 1 minute after mild driving, to 5 minutesafter aggressive driving. The idle-down procedure circulates fresh oil and coolant through the turbo-

charger, allowing it to cool gradually, prior to shutdown.

Cool down is required to be performed at the end of every hard driving session. Otherwise,the rapid heat build-up from high boost/high rpm operation can cause the turbine shaft tosoften, and allow the turbine head to droop. The result is an imbalance that ultimatelyleads to turbine shaft failure. Improper cool down in the most common cause of turbo fail-ure and is grounds for warranty denial.

Aftermarket boost control devices, electronic or mechanical, are not to be used with thiskit. All boost control is done by fuel injection computer, and excessive boost without fuelinjection control can lead to engine and turbo damage. Use of these devices is grounds forwarranty denial.

MAINTENANCE

1. Engine oil and filter should be replaced every 3000 miles. Do not change engine oil without install-ing a new oil filter. Check your engine oil level frequently. The turbocharger shaft spins over 10 timesfaster than your engine's crankshaft, so an adequate oil supply is critical.

2. Periodically inspect the turbocharger to determine if the wastegate rod and hardware has been bentor damaged. The K04 wastegate rod comes from the factory with a locking clip over the adjustmentnuts. DO NOT attempt to recalibrate the wastegate by moving the adjustment nuts. Any tamperingwith the wastegate can dramatically alter the boost characteristic of the turbocharger and lead to seri-ous engine damage.

3. In the event that any air intake hoses are removed or disconnected during any service, thoroughlyinspect every hose and remove any foreign objects or debris that may have fallen or collected inside the

hose(s). Any loose objects inside the air intake tract may be sucked into the turbocharger upon startup, seriously damaging the compressor blades.


4/4

Thank you for choosing A.W.E. Tuning as your performance automotive parts supplier. Please re-member that a performance car is only as strong as its weakest link. Therefore, it is vital that youmaintain your vehicle to factory specifications.

By installing or using the purchased product, the Consumer accepts this warranty andany specific Manufacturer warranties enclosed.

Limited Warranty

The following warranty is valid only in the United States and Canada.

The Manufacturers full warranty applies to all products sold.

Secor Ltd. (A.W.E. Tuning) warrants to the original retail purchaser (Consumer) this product:

90 days on turbo unitBalance of parts 1 year

Upon verification of warranty coverage, A.W.E. Tuning will replace the defective product withoutcharge. This is the only remedy the Consumer has for any loss or damage, however arising, due tononconformity in or defect of the product. This warranty does not cover consequential damage, loss

of time or revenues, inconvenience, loss of use of vehicle, damage to the vehicle or components, orother incidental or indirect damage.

All warranties are void if the product was not installed by a certified auto mechanic, improperly ser-viced, modified, or used in a way not intended by the Manufacturer. Use of product in Motorsportsor Racing conditions is grounds for warranty denial. Motorsports and Racing is an inherently abusiveoperational condition, and it is impossible to warranty for this type of usage.

The Consumer is responsible for ensuring that the product is installed in a safe and proper manner,and should cease usage of the product immediately if an unsafe or improper condition is noted. Ifan unsafe or improper condition is noted, the Consumer should then immediately contact the facilitywhere the product was installed or A.W.E. Tuning.

Please contact us first for any warranty claims or explanations of this document.

AWE Tuning2385C Maryland RoadWillow Grove, PA 19090215-658-1670

[email protected]

awe mkv k04 kit

Documents