AUTOMOTIVE TOOLS

ACCESSORY BELT DRIVE SYSTEMS

BELT MEASURERMEASURES AUTOMOTIVE V-BELTS AND MICRO-V BELTSMeasures V-belts up to 2540mm in length and Micro-V beltsup to 2720mm in length, also measures the belt width.

Part Number: GVMVBM

KRIKIT™ V-BELT TENSION GAUGETHIS EASY-TO-USE GAUGE IS DESIGNED FOR TENSIONING ALLAUTOMOTIVE V-BELTS UP TO, AND INCLUDING, 22M TOP WIDTHS> Scale reads in pounds and kilograms. Measures tension from 30 to 160lbs., and 15 to 75 kg

> Die-cast aluminum body, nylon indicator arm and pressure pad> Fits in pocket with stainless steel pocket clip

> Packaging: Individually boxed

Part Number: 91107

Note: Not for use on timing belts.

KRIKIT™ II MICRO-V AT® (V-RIBBED)BELT TENSION GAUGEDESIGNED FOR TENSIONING V-RIBBED BELTS ON PASSENGER CARS,LIGHT TRUCKS, HEAVY TRUCKS AND BUSES> Bright green pressure pad and indicator arm

> Calibrated to measure tension from 100 to 320 lbs., and 50 to 150 kg

> Measure belts up to eight ribs in width

> Packaging: Individually boxed

Part Number: 91132Note: Not for use on timing belts.

AUTOMOTIVE TOOLS

BELT WEAR GAUGEBELT WEAR GAUGE - NEW AND IMPROVED. EASIER TO USE!

The Gates Belt Wear Gauge was designed with input from automotivetechnicians. It is easy to use and gives instant pass / fail results. You canuse it on or off the vehicle, one-handed, and even in places where youcan’t see.

How To Inspect Today’s BeltsToday’s serpentine belts wear out gradually, much like a tire, and don’t always show signs of visual wear. A serpentine belt can appear to be in good condition when it’s actually near failure. Belts manufactured before the year 2000 show obvious failure signs such as cracks. The Gates Belt Wear Gauge provides a simple and reliable way to determine if a serpentine belt has lost enough material to negatively affect performance and warrant replacement.

Part Number: BELT-WEAR-GAUGE VISIT: WWW.GATESAUSTRALIA.COM.AU/BELTWEAR TO GET A FREE GAUGE.

DRIVEALIGN® LASER TOOLACCURATE ALIGNMENT, EVERY TIME

UPDATED TOOL FOR MISALIGNMENT DETECTIONDesigned to detect misalignment in serpentine drive systems, the

two-piece kit contains a laser tool and a target piece, both of which

are anodised red for high visibility in dark engine compartments.

The laser beam itself is a large vertical line, and when coupled with

the precisely etched groove in the target piece, can be used to easily

identify misaligned pulleys and components. The tool works on

automotive serpentine belt drives with 4 ribs or more.

FEATURES> Laser type: 650nm visible laser diode

> Operating time: 20 hours of continuous service

> Battery type: replaceable lithium battery

> Specially designed magnetic feet to sit perfectly in K-section

Micro-V pulleys

> Neatly packaged in a blow-molded plastic case for durability during

handling and storage

Part Number: 91075

DRIVE ALIGN® LASER ALIGNMENT TOOLEXCLUSIVE, PATENTED TOOL IS COMPATIBLE WITH ALL AUTOMOTIVE SERPENTINE BELT DRIVES

Quickly identifies two most common types of pulley misalignment – parallel offset and angular – that reduce belt and pulley service life and produce unwanted noise. Simply position tool within grooves of pulley and aim laser beam at opposite pulley.

> Lightweight, easy-to-use tool includes special laser enhancement glasses for easy viewing in all light conditions

> Comes with high-impact resistant carrying case

Part Number: 91006

www.GatesAustralia.com.au

GATES AUSTRALIA PTY LTD

1-15 Hydrive Close, Dandenong South, Victoria, 3175

PH: +61 3 9797 9666 FAX: +61 3 9797 9600

BELT WEAR GAUGEBELT WEAR GAUGE - NEW AND IMPROVED. EASIER TO USE!

The Gates Belt Wear Gauge was designed with input from automotive technicians. It is easy to use and gives instant pass / fail results. You can use it on or off the vehicle, one-handed, and even in places where you can’t see.

How To Inspect Today’s Belts Today’s serpentine belts wear out gradually, much like a tire, and don’t always show signs of visual wear. A serpentine belt can appear to be in good condition when it’s actually near failure. Belts manufactured before the year 2000 show obvious failure signs such as cracks. The Gates Belt Wear Gauge provides a simple and reliable way to determine if a serpentine belt has lost enough material to negatively affect performance and warrant replacement.

AUTOMOTIVE TOOLS

Scan to find out more on Gates Automotive Tools.

Gates Tools Flyers x2.indd 2 7/10/2015 11:15 am

DRIVE ALIGN® LASER ALIGNMENT TOOLEXCLUSIVE, PATENTED TOOL IS COMPATIBLE WITH ALL AUTOMOTIVE SERPENTINE BELT DRIVES

Quickly identifies two most common types of pulley misalignment – parallel offset and angular – that reduce belt and pulley service life and produce unwanted noise. Simply position tool within grooves of pulley and aim laser beam at opposite pulley.

> Lightweight, easy-to-use tool includes special laser enhancement glasses for easy viewing in all light conditions

> Comes with high-impact resistant carrying case

Part Number: 91006

www.GatesAustralia.com.au

GATES AUSTRALIA PTY LTD

1-15 Hydrive Close, Dandenong South, Victoria, 3175

PH: +61 3 9797 9666 FAX: +61 3 9797 9600

BELT WEAR GAUGEBELT WEAR GAUGE - NEW AND IMPROVED. EASIER TO USE!

The Gates Belt Wear Gauge was designed with input from automotive technicians. It is easy to use and gives instant pass / fail results. You can use it on or off the vehicle, one-handed, and even in places where you can’t see.

How To Inspect Today’s Belts Today’s serpentine belts wear out gradually, much like a tire, and don’t always show signs of visual wear. A serpentine belt can appear to be in good condition when it’s actually near failure. Belts manufactured before the year 2000 show obvious failure signs such as cracks. The Gates Belt Wear Gauge provides a simple and reliable way to determine if a serpentine belt has lost enough material to negatively affect performance and warrant replacement.

AUTOMOTIVE TOOLS

Scan to find out more on Gates Automotive Tools.

Gates Tools Flyers x2.indd 2 7/10/2015 11:15 am