at10.1 series - yokapower...combining the performance and accuracy of a microprocessor with the...

12
AT10.1 Series RESERVE POWER Float Battery Chargers Advanced technology microprocessor control BATTERY CHARGER RANGE SUMMARY Constant potential DC power supplies for: Floating and charging stationary batteries Power for utility, UPS and communications or industrial type loads Publication No: US-AT10-RS-002 April 2013

Upload: others

Post on 15-Feb-2020

1 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: AT10.1 Series - YokaPower...Combining the performance and accuracy of a microprocessor with the reliability of SCR power conversion technology makes the AT10.1 Series the standard

AT10.1 Series

RESERVEPOWER

Float Battery Chargers

Advanced technology microprocessor control

BATTERY CHARGER RANGE SUMMARY

Constant potential DC power supplies for:

• Floating and charging stationary batteries

• Power for utility, UPS and communications or industrial type loads

Pu

blic

atio

n N

o: U

S-A

T10

-RS

-002

A

pri

l 201

3 S

ub

ject

to

ch

ang

e w

ith

ou

t p

rio

r n

oti

ce. E

.& O

.E.

Publication No: US-AT10-RS-002 April 2013

Page 2: AT10.1 Series - YokaPower...Combining the performance and accuracy of a microprocessor with the reliability of SCR power conversion technology makes the AT10.1 Series the standard

Combining the performance and accuracy of a microprocessor with the reliability of SCR power conversion technology makes the AT10.1 Series the standard in stationary battery chargers. AT10.1 chargers are easy to install, operate and maintain. The AT10.1 is packed with the most standard features and best warranty in the industry.

What are the most common applications for the AT10.1?Utility & CommunicationsPower GenerationSubstationsMicrowave Relay SitesSwitchgear

CommercialAlarm SystemsUninterrupted Power SystemsDC Control Systems

ManufacturingEmergency DC PowerDC Operated BreakersAlarm Systems

TransportationSignal SystemsSwitchgearAlarm Systems

Standard Features

AC Input• Group 1 (6-25 Adc) Voltage:

120/208/240Vac Multi-tap 60Hz 480Vac 60Hz 220Vac, 380/416Vac 50/60Hz 550-600Vac 50/60Hz

• Group 2 (30-100 Adc) Voltage: 120, 208, 240 or 480Vac 60Hz 220Vac, 380 or 416Vac 50/60Hz 550-600Vac 50/60Hz

• Input Voltage Tolerance: +10%, -12%

• Input Frequency Tolerance: ±5%

• Efficiency: 85-90% typical for 130Vdc at 50-100% load

• Operating Ambient Temperature 0°F (-18°C) to 122°F (50°C) without derating• Operating Altitude 3300 ft (1000 meters) above sea level without derating• Relative Humidity 0% to 95% (without condensation)• Audible Noise Less than 65 dBA at any point 5ft (1.5m) from any

vertical surface of enclosure• Made in the United States of America

CSA C22.2 · NRTL/C · UL 1012/UL 1564 compliantSeismic qualifiedABS or CE certification available upon request.

What is the AT10.1?

Group AT10.1

• 5 year product warranty

• Universal main control board operates in any AT Series charger

• Alarm assembly with local LEDs and summary relay contact for AC Failure, DC Failure, High Vdc, Low Vdc, Positive(+) and Negative(-) ground fault

• High DC voltage shutdown

• Forced load share during parallel operation

• Float/equalize selector switch with indicating lights

• Manual equalize timer (0-255 hr.) with indicating lights

• AC line failure automatic equalize timer (0-255 hr.) with indicating light

• AC On indicating light

• 1% Digital LED meter for Vdc, Adc, timer hours and alarm settings

• AC input and DC output circuit breakers

• Membrane front panel

• Front panel controls can be disabled for security

• A redundant analog circuit for LVDC alarm, independent of the microprocessor

• Redundant control loops for higher reliability

• Local or remote voltage sense with redundancy to protect against remote sense failure

• Self-diagnostics

• Input & output MOV surge suppressors

• Reverse polarity protection via free wheeling diodes

• CU-AL I/O compression lugs

• Switchboard wire, UL VW-1

• Enclosure pre-treated using a 5-stage iron phosphate process with baked epoxy powder coating in ANSI 61 gray

DC Output• Voltage Ratings:

12, 24, 48, or 130Vdc nominal

• Current Ratings: GROUPI: 6, 12, 16, 20, 25Adc GROUPII: 30, 40, 50, 75, 100Adc

• Continuous Rating: 110% rated current at maximum equalize voltage at 122ºF (50ºC)

• Current Limit Adjustment Range: 50% to 110% rated output

• Voltage Regulation: ±0.25% for line, load and temperature variations

Third party agency approvals:

*Regulation at maximum equalize voltages may not meet ±0.25%

Environmental

• Electrical Noise: 32dBrnc

• Ripple: 12/24/48Vdc · Unfiltered on battery 1% Vrms · Filtered on battery 30mVrms · Filtered off battery 1% Vrms · Battery Eliminator 30mVrms

130Vdc · Unfiltered on battery 2% Vrms · Filtered on battery 100mVrms · Filtered off battery 2% Vrms · Battery Eliminator 100mVrms

• Surge Withstand Capability: Meets IEEE-472, ANSI C37.90a

Specifications

AT10.1 Float Battery Charger

2

Page 3: AT10.1 Series - YokaPower...Combining the performance and accuracy of a microprocessor with the reliability of SCR power conversion technology makes the AT10.1 Series the standard

Summary of Options

• DC output filtering: per NEMA PE5 1996, standard and battery eliminator

• Medium and High Amp Interrupting Capacity Breakers

• Auxiliary alarm relay board

• Copper ground bus

• AC lightning arrestor

• Fungus proofing (tropicalization)

• Static proofing

• Communications module: DNP3 Level 2 or MODBUS protocols

• Battery temperature compensation

• Fan control contactor

• Custom Paint

• NEMA 4/12 type enclosure with fan

• Rack mounting

• Wall mounting

• Floor mounting stand

• NEMA Type 2 Drip Shield

• Barrier type alarm terminal block

• Forced load share cable

• End of discharge alarm

• Battery discharge alarm

• Zero-center ground detection meter

• Analog AC voltmeter

• Analog AC ammeter

• Cabinet heater assembly

• CE marking upon request

• ABS certification upon request

• Custom drawing package with optional CAD and PDF files

• AT-DC distribution panel

Ordering

Factory Installation

YES

FilteringStandard

Output filtering is essential whenever there is need for low AC ripple and low noise on the DC bus for critical loads. The standard DC output filtering limits ripple to no more than 30mV RMS on 12, 24 and 48Vdc units, and 100mV RMS on 130Vdc units, measured at the battery terminals. This feature meets the specifications of NEMA standard PE5-1996, and is recommended for installations using VRLA or gelled electrolyte batteries.

Factory Installation use Specification Tables on pages

9 & 10

Available for field

installationYES

Field Installation use Part Number

Group I: EJ1072-9#Group II: EJ5023-9#

Contact manufacturer for specific part number.

Medium and High AIC BreakerThis feature provides thermal-magnetic circuit breakers with higher ratings than the standard. See the tables on pages 9 and 10 for Group I and Group II medium and high AIC breaker ratings. For AT10.1 Group 1, AC and DC breakers ratings must be ordered together, and are supplied in a separate penthouse enclosure. For Group 2, AC and DC breakers can be specified separately and are supplied in the standard cabinet.

Ordering

Factory Installation

YES

Factory Installation use Specification Tables on pages

9 & 10

Available for field

installationNO

Not available for field installation.

Auxiliary Alarm Relay BoardThe AT10.1 features several industry-standard alarms, with individual LED indicators on the front instrument panel, and are accessible to the user via one (1) Summary Alarm contact on the Main Control PC Board. This feature provides a separate user-accessed PC board, featuring discreet two (2) form-C relay contacts for all six (6) alarms. In AT10.1 Group I ratings, the board is supplied in an additional penthouse enclosure. In AT10.1 Group II ratings, it is supplied within the standard enclosure.

Factory Installation

YES

Factory Installation use Specification Tables on pages

9 & 10

Available for field

installationYES

Field Installation use Part Number

Group I: EI0213-0#

Contact manufacturer for specific part number

EI0213-02

Battery Eliminator An additional "battery eliminator" feature is also available, meeting the specifications of NEMA standard PE5-1996 with no battery connected, measured at the DC output terminals. This feature is recommended for sites where the battery may occasionally be disconnected from the DC bus for maintenance. Additional filtering is essential to limit AC ripple and noise for critical DC loads.

Ordering

3

Page 4: AT10.1 Series - YokaPower...Combining the performance and accuracy of a microprocessor with the reliability of SCR power conversion technology makes the AT10.1 Series the standard

Ordering

Ordering

Ordering

Ordering

OrderingCommunicationsThis option allows full remote monitoring of the AT10.1 and control of the front panel features, using MODBUS or DNP3 Level 2 protocols. Standard serial connections are provided for use with local SCADA systems.

Additional Ethernet and Fiber Optics Modem interfaces are also available for use with the AT Communications option. Contact EnerSys for part number.

Static ProofingUsed in "arid" environments, this treatment coats electrical components and connections with a static-resistant, non-conductive film (approximately 1 mil thickness). User termination points, relay contacts and any electrical connectors where the spray would interfere with functionality are not coated. The application is fully cured at time of shipment.

Fungus ProofingThis treatment is also referred to as "tropicalization". It coats electrical components and internal wiring connections with a fungus-resistant, non-conductive film (approximately 1 mil thickness). User termination points, relay contacts and any electrical connectors where the spray would interfere with functionality are not coated. The application is fully cured at time of shipment.

AC Lightning ArresterThis options feature an industrial-grade surge arrestor in polycarbonate housing, rated for 20,000 A. It is recommended for installations with risk of frequent AC surges, such as high elevations or severe weather.

Copper Ground BusThis option provides a convenient means to tie the AT10.1 to the site building ground. A copper ground bus bar is provided at the I/O terminal, with an extra CU-AL compression box lug.

Factory Installation

YES

Factory Installation use Specification Tables on pages

9 & 10

Available for field

installationYES

Field Installation use Part Number

Group I: E10195-00 Group II: E10195-02

Factory Installation

YES

Factory Installation use Specification Tables on pages

9 & 10

Available for field

installationYES

Field Installation use Part Number

Group I: EJ1074-00Group II: EJ1074-01

Factory Installation

YES

Factory Installation use Specification Tables on pages

9 & 10

Available for field

installationNO

Not available for field installation.

Factory Installation

YES

Factory Installation use Specification Tables on pages

9 & 10

Available for field

installationNO

Factory Installation

YES

Factory Installation use Part Numbering

when ordering:

Available for field

installation YES

12Vdc: EJ5037-0124Vdc: EJ5037-0248Vdc: EJ5037-03

130Vdc: EJ5037-04

Not available for field installation.

Summary of Options

4

12Vdc: EJ5037-1124Vdc: EJ5037-1248Vdc: EJ5037-13

130Vdc: EJ5037-14

Field Installation use Part Number:

Page 5: AT10.1 Series - YokaPower...Combining the performance and accuracy of a microprocessor with the reliability of SCR power conversion technology makes the AT10.1 Series the standard

Mechanical Lock for Front DoorThe AT10.1 front panel controls can be disabled by setting a jumper on the back of the Main Control PC Board. For installations where extra security is required, the front instrument panel, or door, can be physically locked closed. This option provides a locking provision on the enclosure, a padlock and two (2) keys. A fully installed door key lock is also available.

Fan Control ContractorLead-acid batteries produce hydrogen gas. This small wall-mounted external accessory provides a relay contactor to activate a battery installation vent or exhaust fan. Available in 10A or 20A models, the accessory is factory-set to provide relay closure when the AT10.1 enters into Equalize mode.

Temperature CompensationSupplied in a kit, this option adjusts the AT10.1 DC output voltage up or down, in response to battery temperature fluctuations. Temperature is measured by an epoxy-enclosed thermistor. This probe is mounted on or near the battery, and connected by a cable to the Main Control PC Board. It is compatible with both lead-acid and nickel-cadmium batteries, and recommended for VRLA batteries. Cable lengths of 25, 50, 100 and 200ft. are available.

Barrier Type Alarm Terminal BlockThis option features a separate molded phenolic terminal block, wired directly to the Auxiliary Alarm Relay PC Board. It allows the user to connect remote alarm wiring with ring or fork type lugs. The terminals are rated for 20A at 150 Vac/Vdc and accept wire sizes #16 to #14 AWG.

Custom PaintAT10.1 NEMA Type 1 enclosures feature an ANSI 61 gray epoxy powdercoat finish. Custom exterior and interior (e.g. semigloss white) colors are available in ANSI, PMS, and RAL color codes to meet specific requirements.

Summary of Options

Factory Installation

NO

Can be ordered with charger but must be

field installed.

Available for field

installationYES

Field Installation use Part Number

25ft: EJ5033-0050ft: EJ5033-01

100ft: EJ5033-02 200ft: EJ5033-03

Factory Installation

YES

Factory Installation use Part Number when ordering

1 FORM C: EJ5130-01 2 FORM C: EJ5130-02

Available for field

installationYES

Field Installation use Part Number

1 Form C: EJ5130-01 2 Form C: EJ5130-02

Factory Installation

YES

Factory Installation use Part Number when ordering

Available for field

installationYES

Factory Installation

NO

Can be ordered with charger but must be

field installed

Available for field

installationYES

Factory Installation

YES

EI5064-00 Specify when

placing order using your specific paint

requirements

Available for field

installationNO

Not available for field installation.

Field Installation use Part Number

10 Amp Rating: EJ507-0# 20 Amp Rating: EJ507-1#

Contact manufacturer for specific part number

Ordering

Ordering

Ordering

Padlock 586/594: EI0215-00 Padlock 5017/5018: EI0215-01 Keylock 586/594: EI0215-10

Keylock 5017/5018: EI0215-11

Ordering

Ordering

5

Page 6: AT10.1 Series - YokaPower...Combining the performance and accuracy of a microprocessor with the reliability of SCR power conversion technology makes the AT10.1 Series the standard

SUPPLEMENTAL PRODUCT

Floor StandThis accessory is provided with smaller wall-mounted AT10.1 chargers when a vertical surface is not desired. The assembly mounts the AT10.1 approximately 44 in. / 1.12 m from the floor. The kit features mounting brackets, assembly hardware to secure the AT10.1 to the brackets, and user instructions with a drilling pattern. Floor mounting anchor bolts are user-supplied.

NEMA Type 2 Drip ShieldStandard AT10.1 battery chargers are supplied in NEMA Type 1 vented enclosures. The optional drip shield prevents overhead water and small falling particles from entering the top vented panels, protecting internal equipment from damage. NEMA Type 2 specification.

AT-DC Distribution Panel This product augments AT10.1 with a customized DC distribution panel for user-specified loads. The AT-DC is configurable to various combinations of main and branch breakers. The AT-DC panel is optimally supplied from the factory, mounted to the AT10.1 and pre-wired to the charger's DC output terminals. For additional product details, including applicable third party agency approvals, refer to the AT-DC literature (JF5032-00).

NEMA Type 4 CabinetWith this accessory, a fully assembled standard AT10.1 NEMA-1 vented enclosure is installed within another gasketed, sealed cabinet. The combined assembly meets the NEMA Type 4 (and therefore Type 12 and 13) enclosure specification. All ratings feature forced cooling, with user-supplied 120Vac for the fan.

Rack Mounting BracketsThese accessories are provided when the AT10.1 enclosure is to be installed into a standard EIA relay rack. Smaller AT10.1 models may be installed into 19in racks, and all AT10.1s may be installed into 23 in. or 24 in. relay racks. All hardware is included for assembling the brackets to the AT10.1. Relay rack mounting hardware is user-supplied.

Summary of Options

Ordering

Ordering

Ordering

Ordering

Ordering

Factory Installation

YES

Factory Installation use Part Number when

orderingSTYLE 586: EI0214-00 STYLE 594: EI0214-00

STYLE 5017: EI5036-00 STYLE 5018: EI5037-00

Available for field

installationNO

Not available for field installation.

Factory Installation

YES

Factory & Field Installation use Part

Number when ordering

Style 586 (19/23/34in): EI093-00

Style 594 (23/24in): EI093-00

Style 5017 (19in): EI093-01

Style 5017 (23/24in): EI093-02

Style 5018 (23/24in): EI093-03

Available for field

installationYES

Factory Installation

YES

Factory Installation use Part Number when

orderingEI0192-00

Available for field

installationYES

Factory Installation

YES

Factory & Field Installation use Part

Number when ordering

Style 586: EI0191-00

Style 594: EI0191-00

Style 5017: EI0191-01

Style 5018: EI0191-02

Available for field

installationYES

Field Installation use Part Number

EI0192-00

Factory Installation

YES

Factory & Field Installation use Part

Number when orderingEJ5110-##

Refer to document (JF5032-00) for model specific part number

Available for field

installationYES

6

Page 7: AT10.1 Series - YokaPower...Combining the performance and accuracy of a microprocessor with the reliability of SCR power conversion technology makes the AT10.1 Series the standard

DC OutputRating

AC Input Ampere RatingBased on maximum rms value of the input current

delivered to the charger under all operating conditions within manufacturer's

specifications

Battery Charger AC Circuit Breaker Ampere Rating

(standard AIC breakers)

DC Circuit

Breaker Rating

Cabinet Style

Approx.Shipping Weightslbs.(kg)

Heat LossWatts

(BTU/hr)

Volts Amps 120Vac

208Vac

220Vac

240Vac

380Vac

416Vac

480Vac

600Vac

120Vac

208Vac

220Vac

240Vac

380Vac

416 Vac

480Vac

600Vac

Float Adjust11.0-

14.5Vdc12Vdc

GROUP I

6 3 2 2 1 1 1 1 1 10 10 10 10 2 2 2 15 10 586 83 (38) 31 (105)

12 3 2 2 2 2 2 1 1 10 10 10 10 4 4 2 15 20 586 87 (40) 58 (199)

16 4 2 3 2 2 2 1 1 10 10 10 10 4 4 2 15 25 586 92 (42) 77 (262)

Equalize Adjust11.7-

15.5.Vdc

20 6 3 3 3 2 2 2 2 10 10 10 10 4 4 3 15 30 586 118 (54) 95 (326)

25 7 4 4 4 3 2 2 2 10 10 10 10 5 5 4 15 40 586 100 (46) 119 (404)

12VdcGROUP

II

30 9 6 5 5 3 3 3 2 15 10 10 10 5 5 5 15 50 5017 184 (84) 142 (483)

40 11 7 6 6 4 3 3 3 20 10 10 10 5 5 5 15 60 5017 189 (86) 188 (641)

Extended Equalizeto 16Vdc*

50 14 8 8 7 5 4 4 3 20 15 15 15 10 10 5 15 80 5017 194 (88) 234 (798)

75 21 13 12 11 7 6 6 5 35 20 20 20 10 10 10 15 100 5018 199 (91) 350 (1192)

100 28 16 15 13 10 8 8 8 40 25 20 25 15 15 15 15 150 5018 225 (103) 465 (1587)

Float Adjust22.0-

29.5Vdc24Vdc

GROUP I

6 5 3 3 3 2 1 1 1 10 10 10 10 3 3 3 15 10 586 99 (45) 40 (136)

12 8 5 4 4 3 2 2 1 10 10 10 10 4 4 3 15 20 586 109 (50) 75 (255)

16 9 6 5 5 4 3 3 2 15 15 15 15 6 6 4 15 25 586 115 (53) 98 (334)

Equalize Adjust23.4-

31.0Vdc

20 11 7 6 6 5 4 4 3 15 15 15 15 8 8 6 15 30 586 119 (54) 121 (413)

25 14 9 8 7 6 4 4 4 20 20 20 20 8 8 6 15 40 586 136 (62) 150 (512)

24VdcGROUP

II

30 16 8 8 8 5 5 4 4 20 10 10 10 10 10 5 15 50 5017 259 (118) 179 (612)

40 20 12 12 11 8 7 6 5 25 15 15 15 10 10 10 15 60 5017 267 (122) 237 (810)

Extended Equalizeto 32Vdc*

50 26 15 15 14 8 8 7 6 35 20 20 20 10 10 10 15 80 5017 342 (156) 295 (1008)

75 42 26 23 22 14 13 11 10 70 35 30 35 20 20 15 15 100 5018 355 (162) 441 (1503)

100 51 25 24 22 14 12 11 11 80 35 30 35 25 25 20 15 150 5018 360 (164) 586 (1999)

Float Adjust44.0-

58.0Vdc48Vdc

GROUP I

6 9 5 5 5 4 3 3 2 15 15 15 15 6 6 4 15 10 586 105 (48) 60 (203)

12 15 9 9 8 5 4 4 3 20 20 20 20 8 8 6 15 20 586 120 (55) 107 (365)

16 18 12 11 10 7 5 5 4 25 25 25 25 10 10 8 15 25 594 155 (71) 139 (473)

Equalize Adjust46.8-

59.0Vdc

20 23 13 13 12 9 6 6 5 30 30 30 30 13 13 8 15 30 594 170 (78) 170 (581)

25 29 17 17 16 12 8 8 7 40 40 40 40 15 15 10 15 40 594 180 (82) 210 (717)

48VdcGROUP

II

30 28 16 16 15 8 8 7 6 35 20 20 20 15 15 15 15 50 5017 217 (99) 250 (852)

40 38 22 19 19 12 11 9 8 50 30 25 30 15 15 15 15 60 5017 225 (103) 329 (1122)

Extended Equalizeto 61Vdc*

50 52 28 28 26 16 15 12 11 70 35 35 35 20 20 15 15 80 5017 250 (114) 408 (1392)

75 79 48 43 39 25 22 19 17 100 60 60 60 35 35 25 25 100 5018 433 (197) 606 (2068)

100 88 50 48 44 28 25 22 19 125 70 60 70 40 40 35 25 150 5018 450 (205) 804 (2743)

Float Adjust110.0-

140.0Vdc130VdcGROUP

I

6 15 9 8 8 5 5 4 4 20 20 20 20 8 8 8 15 10 586 130 (59) 99 (337)

12 32 18 16 15 10 9 8 7 40 40 40 40 13 13 13 15 20 594 155 (71) 167 (571)

16 34 20 18 17 11 10 9 8 50 50 50 50 13 13 13 15 25 594 215 (98) 213 (727)

Equalize Adjust117.0-

143.0Vdc

20 40 24 23 23 15 14 12 11 60 60 60 60 20 20 20 15 30 594 225 (103) 259 (883)

25 50 30 28 27 18 16 14 12 70 70 70 70 25 25 20 15 40 594 265 (120) 316 (1078)

130VdcGROUP

II

30 75 44 42 40 23 22 20 16 100 60 60 60 35 35 25 20 50 5017 285 (130) 373 (1273)

Extended Equalize

to 149Vdc*

40 100 59 57 53 35 32 28 17 125 80 80 80 60 60 35 30 60 5018 340 (155) 484 (1664)

50 N/A 72 68 63 40 36 32 28 N/A 100 100 100 50 50 40 35 80 5018 375 (171) 602 (2054)

75 N/A 100 83 81 52 47 40 36 N/A 125 125 125 70 70 50 50 100 5018 482 (219) 888 (3030)

*Regulation at max. equalize voltages may not meet ±0.25%

AT10.1 Specification Chart

7

Page 8: AT10.1 Series - YokaPower...Combining the performance and accuracy of a microprocessor with the reliability of SCR power conversion technology makes the AT10.1 Series the standard

NOTE: Dimensions shown are for reference only; for installation and mounting please refer to user manual.

Group 1 6-25Adc

Cabinet Style 586

Cabinet Style 5018

Cabinet Style 5017

Group 2 30-100Adc

Cabinet Style 594

8

Page 9: AT10.1 Series - YokaPower...Combining the performance and accuracy of a microprocessor with the reliability of SCR power conversion technology makes the AT10.1 Series the standard

Group 1 6-25Adc

MicroprocessorControl Board

I/O Assembly

Filter Assembly

Output Circuit Breaker

Input Circuit Breaker

Main InductorMain Transformer

Rectifier Assembly

A B C D E F G H J K L

AT10 0 1 2 0 0 6 E 2 4 0 S A U X G L X X

AT10

Description Code Features

A AT10 AT10 Series

BNominal DC

Output Voltage

012 12Vdc

024 24Vdc

048 48Vdc

130 130Vdc

CNominal DC

Output Current

006 6Adc

012 12Adc

016 16Adc

020 20Adc

025 25Adc

DDC OutputFiltering

U Unfiltered

F Filtered

E Batt. Eliminator

EAC Input Voltage

120 120V 60Hz

208 208V 60Hz

240 240V 60Hz

480 480V 60Hz

220 220V 50/60Hz

380 380V 50/60Hz

416 416V 50/60Hz

600 550-600V 50/60Hz

This ordering code is unique for AT10.1 chargers rated 6-25A output.

Description Code Feature

FCircuit

Breaker Rating

S Standard AIC

M Medium AIC

H High AIC

GAuxiliary Alarm

Relay BoardAUX Installed

XXX Not Supplied

HCopper

Ground BusG Installed

X Not Supplied

JAC Lightning

ArrestorL Installed

X Not Supplied

K Fungus ProofingF Applied

X Not Supplied

L Static ProofingS Applied

X Not Supplied

SAMPLE

YOUR CODE

GROUP I (6-25 Adc) - Specification Table

Circuit Breaker AC & DC Ratings

*For chargers 16Adc and larger; consult factory for other ratings.

10kAIC - 240Vac 10kAIC - 480Vac10kAIC - 125Vdc*

Input:

Output:

25kAIC - 240Vac 18kAIC - 480Vac18kAIC - 600Vac10kAIC - 250Vdc

Input:

Output:

65kAIC - 240Vac25kAIC - 480Vac 18kAIC - 600Vac 20kAIC - 250Vdc

Input:

Output:

Standard

Medium

High

9

Page 10: AT10.1 Series - YokaPower...Combining the performance and accuracy of a microprocessor with the reliability of SCR power conversion technology makes the AT10.1 Series the standard

A B C D E F G H J K L M N P

AT10 1 3 0 0 5 0 F 4 8 0 S F S X A X X X X

AT10

Description Code Feature

A AT10 AT10 Series

BNominal DC

Output Voltage

012 12Vdc

024 24Vdc

048 48Vdc

130 130Vdc

CNominal DC

Output Current

030 30Adc

040 40Adc

050 50Adc

075 75Adc

100 100Adc

DDC OutputFiltering

U Unfiltered

F Filtered

E Batt. Eliminator

E

AC Input Voltage*

*Group 2 inputs cannot be

retapped in field

120 120V 60Hz

208 208V 60Hz

240 240V 60Hz

480 480V 60Hz

220 220V 50/60Hz

380 380V 50/60Hz

416 416V 50/60Hz

600 550-600V 50/60Hz

Description Code Feature

FAC Input

Circuit Breaker Rating

S Standard AIC

M Medium AIC

H High AIC

0 No Breaker

G AC Input FusesF Installed

X Not Supplied

HDC Output Circuit

Breaker Rating

S Standard AIC

M Medium AIC

H High AIC

0 No Breaker

J DC Output FusesF Installed

X Not Supplied

KAuxiliary Alarm

Relay BoardA Installed

X Not Supplied

LCopper

Ground BusG Installed

X Not Supplied

MAC Lightning

ArrestorL Installed

X Not Supplied

N Fungus ProofingF Applied

X Not Supplied

P Static ProofingS Applied

X Not Supplied

I/O Assembly

Output Circuit Breaker

Input Circuit Breaker

Main Inductor

Main Transformer

Rectifier Assembly

This ordering code is unique for AT10.1 chargers rated 30-100A output.

MicroprocessorControl Board

YOUR CODE

Circuit Breaker AC & DC Ratings

5kAIC - 120/208/240/480Vac5kAIC - 125Vdc

Input:Output:

25kAIC - 120/208/240/480Vac18kAIC - 600Vac10kAIC - 250Vdc

Input:

Output:

65kAIC - 120/208/240/480Vac25kAIC - 600Vac20kAIC - 250Vdc

Input:

Output:

Standard

Medium

High

GROUP II (30-100 Adc) - Specification TableSAMPLE

Group 2 30-100Adc

10

Page 11: AT10.1 Series - YokaPower...Combining the performance and accuracy of a microprocessor with the reliability of SCR power conversion technology makes the AT10.1 Series the standard

• AT30 Microprocessor Battery Charger• AT Series Options and Accessories• AT Series Communications Module• AT-DC Series Distribution Panel• SCR/SCRF Series Utility Battery Charger

• UMC Universal Maintenance Charger• Single Cell Charger• Mobile DC Power System• The EPIC Series Console• Best Battery Selector

Other products available

11

Notes

Page 12: AT10.1 Series - YokaPower...Combining the performance and accuracy of a microprocessor with the reliability of SCR power conversion technology makes the AT10.1 Series the standard

EnerSysWorld Headquarters2366 Bernville RoadReading, PA 19605USATel: +1 610 208 1991 +1 800 538 3627Fax: +1 610 372 8613

EnerSys EMEAEH Europe GmbHLöwenstrasse 328001 ZurichSwitzerland Tel: +41 44 215 7410

EnerSys Asia152 Beach Road Gateway East Building#11-03189721 Singapore Tel: +65 6508 1780

© 2013 EnerSys. All rights reserved. Trademarks and logos are the property of EnerSys

and its affiliates unless otherwise noted.

Pu

blic

atio

n N

o: U

S-A

T10

-RS

-002

A

pri

l 201

3 S

ub

ject

to

ch

ang

e w

ith

ou

t p

rio

r n

oti

ce. E

.& O

.E.

#