assembly instructions elevatetm original corner€¦ · tm original corner caution moving parts can...

ASSEMBLY INSTRUCTIONS

Anthro Corporation® | 10450 SW Manhasset Dr. | Tualatin, OR 97062Toll-free: 800.325.3841 | Fax: 800.325.0045 | email: [email protected] | anthro.com

Outside the U.S. | Tel: 503.691.2556 | Fax: 503.691.2409

ElevateTM Original Corner

CAUTION

Moving parts can crush.

Use care when

operating.

Part Number: ELBCzz-xx4

November 2013

CAUTION

This table holds up to 300 lbs. of distributed weight and 90 lbs. over one leg.

IHW

Touchboards_stamp

http://www.touchboards.com/

PARTS LISTBefore beginning assembly of your Table, please take a moment to review the parts listed below to verify that your shipment is complete. A Phillips head screwdriver is required for this assembly. A 7/16" Socket with extension and wrench will make this assembly go more smoothly. A 7/16" Open-end Wrench or Adjustable Wrench are useful substitutions.

2

WELCOMEThank you for purchasing Elevate,™Corner! If you have any questions or if we can help you in any way, please contact us at 800.325.3841.

This assembly requires two people.

Product Quantity Part Number

01 Center Shelf 1 101-1143-01-00

02 Side A Wing Shelf 1 101-1145-01-00

03 Side B Wing Shelf 1 101-1146-01-00

04 Cross Tube 4 125-5317-00

05 4" Locking Caster 6 150-5065-00

06 Velcro Tie (not shown) 4 175-5121-03


07 3.5" Grommet 2 175-5147-00

08 Basetube End Cap 4 175-5158-32

09 Wire Managment Clip 3 175-5188-00

10 Crosstube End Cap 4 175-5190-32

11 Shelf Gusset (X) 1 225-2269-00

12 Shelf Gusset (Y) 1 225-2270-00

13 Cableway 2 225-2282-00

14 Junction Plate 4 225-2463-00

15 Draw Latch Plate X 2 225-4785-00

16 Draw Latch Plate Y 2 225-4786-00

17 Leg Plate 1 225-2565-00

18 Corner Gusset 1 225-2566-00

19 Corner Shelf Cap 1 225-2567-00

20 Curved Washer 4 225-3522-00

21 3/4" Button Head PB Screw 8 325-5575-00

22 1/2" Button Head Cap Screw 12 325-5003-00

23 4" Cap Screw 4 325-5166-00

24 3.5" Bolt 8 325-5194-00

25 1/4-20 Lock Nut 2 325-5259-00

(CONTINUED NEXT PAGE)

141516

26

21

22

20

19

18

17

01

02

09

04

03

05

07

08

10

111213

28

29

27 30

26

25

23

24

31

34

37

38

3940

4142

ElevateTM Original Corner Assembly Instructions 3

STEP 1Assemble the Worksurface

� Place the three worksurface components upside down on a non-marring surface. Align each wing to the corner piece so the curved outer edges line up and the channels at the center of each piece meet. [A]

� Align the two halves of each latch assembly so that the threaded bolt hole on one half of the assembly aligns with the unthreaded bolt hole. Loosely connect the two halves of the assembly by driving one 3.5" Bolt through the unthreaded hole and into the threaded hole. [B]

� Place one latch assembly into the center slot of the three slots where the corner worksurface component meets one of the wings. Align the screw holes in the latch assembly with the holes on the worksurface components.

� Attach the latch assembly to the tops with #6-9x1" Flat-hd Screw using a Phillips screwdriver, then tighten the 3.5" Bolt just as tight as it will go. Loosely install two junction plates in the slots surrounding the latch assembly with six more #6-9x1" Flat-hd Screws. [C]

� Repeat for the second latch assembly and junction plates on the other wing.

� Tighten all Phillips screws.


26 20mm Socket Head Cap Screw 16 325-5272-00

27 #6-9x1" Flat Hd Screw 44 325-5716-00

28 3/4" Phillips Head Screw 4 325-5370-00

29 Flat Washer 4 325-5379-00

30 Zip Tie Screw Mount 4 400-5152-00

31 Keypad Assembly 1 Keypad 400-5357-00 Keypad Slider 400-5358-00

32 2-meter Control Box Cable 1 400-5180-00 (not shown)

33 1-meter Control Box Cable 3 400-5182-00 (not shown)

34 Control Box 2 400-5215-00

35 Zip Tie Panel Mount 2 400-5239-00

36 10' Power Cord Y (not shown) 1 400-5240-00

37 Patch Cable (not shown) 1 400-5241-00

38 Basetube 2 500-1005-00


39 Cross Tube (X) 1 500-5024-00

40 Cross Tube (Y) 1 500-5025-00

41 Leg 4 575-5018-00

42 Anthro Medallion 2 725-5014-00

43 Anthro 3 Way Wrench (not shown) 1 225-5196-00

44 Hex Driver (not shown) 1 375-5000-00

45 5/32" Hex Driver Bit (not shown) 1 375-5003-00

46 5mm Hex Key (not shown) 1 375-5014-00

47 Rubber Mallet (not shown) 1 375-5022-00

48 5mm Hex Key (not shown) 1 375-5014-00

49 1/4" Hex Key (not shown) 1 375-5024-00

50 #2 Phillips Bit (not shown) 1 375-5009-00

PARTS LIST (CONTINUED)

3.5” Bolt325-5194-00 #6-9x1” Flat-Hd Screw

325-5716-00

A

B

C

4 Questions? Call us at 800.325.3841 or visit anthro.com. We’re happy to walk you through the assembly!

STEP 7Assemble the Corner Leg Assembly and Install

� Align a leg with the inside of the Corner Gusset so that the Slot is facing the open corner and the cord goes to the inside. Attach using eight Socket Head Cap Screws.

� Repeat for the second leg.

� Align the Corner Leg Assembly with the hole array on the Top. Make sure that the cords are to the inside. Secure the Leg Assembly to the Top Assembly using 1" Button-hd PB Screws.

STEP 6Assemble the Outside Legs

� Align a leg with the opening on the base tube so that the welded slot bracket on the legs is facing the hole on the base tube and that the cord comes out the top.

� Attach with four Socket Head Cap Screws.

� Repeat for the other leg.

� Align each shelf gusset with a leg as shown so that the side of the gusset doesn't block the cord.

� Attach each shelf gusset to a leg with four Socket Head Cap Screws.

20mm Socket Head Cap Screw 325-5272-00

Shelf Gusset (X) Shelf Gusset (Y)

Rear

Front Front


Slot Slot

Slot

1” Button Hd PB Screw325-5580-00


STEP 9Install the Outside Leg Assemblies

� Align one Outside Leg Assembly with the hole array on the Top Assembly. Make sure that the Leg Gusset is to the outside of the table and the cable is to the inside of the table. Also verify that the slot on the leg lines up with the hole in the base tube. (See the image on Step 6.)

� Tilt this Outside leg Assembly into place with the top of its Cap Screws seated into the notches on the shelf. But don't attach with wood screws...not yet. [Image A]

� Loosely attach the Cross Tubes into this Leg Assembly using 4" Cap Screws and Curved Washers. Make sure that the curves at the ends of the Cross Tubes line up with the round Base Tube. [Image B]

� Repeat for the other outside leg.

STEP 8Assemble the Corner Base Assembly

� Attach a pair of Cross Tubes to one side of the Corner Shelf Cap using two Flat Washers and two 3.5" Bolts. Tighten the fasteners all the way.

� Repeat for the second pair of Cross Tubes.

� Align the Leg Plate over the Corner Shelf Cap and slide into place. Using a 7/16" socket, open end wrench, adjustable wrench, or the Anthro three-way wrench, tighten four Lock Nuts onto the threaded pins.

� Secure the side of the Leg Plate to the Corner Shelf Cap using 1/2" Button Head Cap Screws. Drive the screws from the outside in.

� Lift this Corner Base Assembly over the center legs and seat them in place, but don’t attach them!

3.5" Bolt 325-5194-00

Flat Washer325-5379-00

1/2" Button Head Cap Screw 325-5003-00

Lock Nut 325-5259-00

A

4" Cap Screw325-5166-00

Curved Washer225-3522-00

B


STEP 11AInstall Control Boxes, Key Pad, and Connect Cables

� Align one Control Box with the hole pattern on the Top Assembly inside the Corner Gusset. Secure using four 3/4" Button-hd PB Screws.

� Align another Control Box with the hole pattern on either side of the Top Assembly in between the Corner Gusset and the Junction Plate. Secure using 3/4" Button-hd PB Screws.

� Connect the Leg Cables to the Control Boxes. Send the short cables to the closer legs and the long cable to the furthest outside leg.

� Connect the two Control Boxes with the Patch Cable.

� Align the Keypad and its housing with the four pre-drilled holes at the front of the table so that the buttons are face-down at the front edge of the table and the flat side of the housing is against the shelf. Using four silver 3/4" Phillips Head Screws, attach the Keypad and its housing to the table.

� Plug the power cords into the control boxes.

STEP 11BInstall Cable Ties

� Insert Cable Clips into the Table and route cords through them. Make sure that cords will clear sharp edges and pinch points when the legs are in motion.

�Plug the Keypad Cable into the Control Box. Insert a Cable Clip into the Table and route the cable through it.

STEP 10Connect the Legs to the Corner Base Assembly

� Using the 3/16" Hex Key, loosely attach the Corner Base Assembly to the Legs with Socket Head Cap Screws.

� Using the 5/32" Hex Driver (or the 5/32" Hex Bit and your electric driver/drill), attach the Outside Leg Assemblies to the top with 1" Button-hd PB Screws.

� Tighten all the screws except the outside screws on the Cross Tubes.

3/4" Phillips Head Screw325-5370-00

Wire Managment Clip

Zip Tie Screw MountZip Tie Panel Mount


Keypad Detail


3/4" Button Hd PB Screw 325-5575-00


STEP 14Cross Bars

� Using the keypad, move the shelf all the way up. (Check the legs for excess lubricant and wipe down if needed.)

� Align one Cross Bar so that the tapered ends of the cross bar brackets line up with the leg brackets. Using the mallet, drive the Cross Bar completely into place (a few whacks on the left, a few on the right, then left, then right…).

� Repeat for the second Cross Bar.

� Tighten the outside screws on the Cross Tubes.

STEP 13Install casters and turn it over!

� Thread casters into the inserts in each leg. This is a lot easier if you lock the casters first.

� With the help of another person, carefully rotate the Table onto its casters.

� Plug the power cord into the Control Boxes and an outlet. Insert a cable clip into the base tube closest to the Control Boxes and route the power cord through it.

STEP 12Install the Cable Troughs

� Align each cable trough with the flanges on each leg gusset and the pre-drilled holes on the shelf. Before installing the trough, make sure that cables are routed through the ends of the trough, not into the side of the trough. Secure the troughs to the gussets with Button Head Cap Screws. Secure the troughs to the shelf using 1" Button-hd PB Screws.

1/2" Button Head Cap Screw 325-5003-00

Cable Snap-in Clip175-51188-00



STEP 15Home the legs

� Press down button until the table reaches its lowest point and stops moving. Release the button for 1-2 seconds. Press down button again for 3-5 seconds and you will see the table home itself.

� Press up button until the table tops at the highest point and hold for 3-5 seconds. Press the down button for 2-3 seconds, then the up button again until it tops at the highest point and hold again for 3-5 seconds. (The goal is to have the table hold at it’s highest point twice.)

� If the legs ever fail to function properly, unplug the power cord, wait 10 seconds, plug the power cord back in and repeat the above steps.

� Legs must also be homed any time that power is disconnected from the legs.

� If the legs are not homed at both the top and the bottom, the table will only move at half its normal speed.

STEP 16Add Accessories and Install Your Equipment

� Now add your Anthro accessories and install your equipment.

� A word of caution: the height range of Elevate may be longer than the cords on your equipment. Equipment that is mounted in a SideRack w/Caster or Equipment Shelf, for example, will not move up and down with the table. Raise and lower the table to its highest and lowest positions when all equipment is installed to make sure that the cords are long enough. Double-check that all the table's cords and cables reach comfortably through the table's entire range of motion.

STEP 17Insert Grommets and End Caps

� Slip the grommet covers into place. (Gently whack them with the mallet if they’re stubborn.)

� Pop end caps into the cross bars and base tubes. Use the mallet to set them into place.

Congratulations! Your assembly is complete! End Cap

Grommet

*300-5596-00*300-5596-00

Warranty: Elevate Original Corner has a Lifetime Warranty against manufacturing defects, two years for the electrical system. Cords and plugs

are not warranted.

Notices:Technology Furniture and Elevate are trademarks of Anthro Corporation. Anthro reserves the right to modify the design and

specifications without prior notice.

IHW

Touchboards_stamp

http://www.touchboards.com/

assembly instructions elevatetm original corner€¦ · tm original corner caution moving parts can...

Documents