assa abloy - e.d. locks & security | commercial ... · backplate reed switch chain open / close...
TRANSCRIPT
62
3 1 4
8 7 9 1210
511
Tools required
bull 18rdquo allen wrench (included) bull Power drill and set of drill bitsbull Flat blade screwdriver (potentiometer amp terminal size) bull Center punchbull Screwdriver (Phillips size 2) bull Wire stripperbull Tape ruler bull 7 drill 14-20 tap (metal frame install)
bull servicing or cleaning
bull To reduce the risk of injury or person use the operator only with Pedestrian Swing doors
bull This operator is for indoor use only
Always disconnect the main power to the operator prior to bull circuit from the main circuit breaker panel and must NOT be connected into any building lighting system that operates flourescent lights
bull Maximum door size 48 in (1219mm) wide x 250 lb (1134kg)
120VAC power supplied to the operator must be a dedicated
WARNINGS
reg5700 LEO Power Operator
Installation and Instruction Manual
Series
ASSA ABLOY80-9357-0008-020 (Rev 3)
Item No Description
1 Back plate
2 Door Closer (1601LAP or 1601BFLAP)
3 Motor Assembly (5700M)
4 Inverter (5700IN)
5 Cover (5700CVR)
6 OnOff switch
7 Circuit Breaker
8 120VAC Electrical Connections
9 Activation Inputs
10 Door OpenClosed Position Magnets
11 Optional RF Receiver12 Power Supply - 11A 24V
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Page 2
Hollow Metal Door Frame Reinforcing
FrameMaterial
12 Ga1046 (266)
14 Ga0747 (190)
16 Ga0598 (152)
18 Ga0478 (121)
12 Ga1046 (266)
10 Ga1343 (341)
10 Ga1343 (341)
8 Ga1644 (418)
18 Ga0478 (121)
12 Ga1046 (266)
12 Ga1046 (266)
10 Ga1343 (341)
Reinforcing
Recommended Min Required
Contents
General Informationbull
the 120VAC (60Hz) power input to the LEO door operator be supplied through normally closed alarm contacts of the alarm system alarm panel
bull Power input to LEO door operator must be 120VAC (60Hz) to terminals HOT and COM at terminal strip T1 Earth ground (GND) to green screw on backplate
bull All wiring must conform to standard wiring practice in accordance with national and local wiring codes
bull Note Unless otherwise noted all dimensions are given in inches (millimeters)
bull Minimum suggested and required material thickness for hollow metal frames (skin plus reinforcement) is charted on below
bull Unit is Non-Handed
bull Door must be hung on butt hinges [5rdquo (127mm) max width] or 34rdquo (19mm) offset pivots A separate door and frame preparation template will be supplied for other conditions
bull Door must swing freely through the entire opening and closing cycle before beginning the installation
bull Use of an auxiliary door stop (by others) is always recommended
bull An incorrectly installed or improperly adjusted door operator can cause property damage or personal injury These instructions should be followed to avoid the possibility of misapplication or misadjustment
UL labeled fire or smoke barrier door assemblies require that WARNING Make sure 120VAC (60Hz) input power is turned off at facilityrsquos main circuit breaker before proceeding with installation
General Templating Informationbull Before beginning the installation verify that the door frame is
properly reinforced and is well anchored in the wall
bull Unreinforced hollow metal frames and aluminum frames should be prepared and fitted with 14-20 blind rivet nuts furnished by others
bull Concealed electrical conduit and concealed switch or sensor wires should be pulled to the frame before proceeding
Fasteners for Framebull 14-20 machine screws for hollow metal and aluminumbull No 14 x 2-34rdquo (70mm) long sheet metal screws for wood
Fasteners for Doorbull 14-20 machine screwsbull 38rdquo diameter x 1-58rdquo (41mm) long sex nut
Electrical Informationbull Maximum current draw of unit is 06 amps
bull Breaker Switch protects the motor assembly and inverter and has a 3 amp rating
bull Maximum wire size is12AWG at terminals HOT and COM (120VAC 60Hz) on ldquoT1rdquo Power Input Terminal14AWG at terminals 1 thru 4 on Accessory Terminal 18AWG at terminals 22 thru 25 on ldquoT1rdquo Power Input Terminal
Frame Reinforcement Table
General 2Frame Reinforcement Table Technical Data 2Component Layout 3ADA ANSI UL 3Hinge (Pull) Side Mounting 4Stop (Push) Side Mounting 6 Adjust Power and Opening Closing Cycle 5 7Input Power Configuration 8
Final Setup 8Inverter Details 9Accessory Typical Installations 10Troubleshooting 10RF Receiver Userrsquos Guide 12Hinge (Pull) Side Template 14Stop (Push) Side Template 15
Technical Data
120VAC 60Hz
6 amps
24 V DC max 11 Amp
28 - 48 (71-122 cm)
100-250 lb (45-113 kg)
Input power
Power consumption
Power supply
Door width
Door weight
Door opening angle
Hold open time 5 - 30 seconds (ADA 5 seconds min)
3 ampsCircuit breaker
up to 110deg Pull side up to 170 Push sideManually to 180deg PushPull side
deg
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
BACKPLATE
REED SWITCH
CHAINOPEN CLOSE POSITIONING MAGNETS
ldquoT1rdquo POWER INPUTTERMINAL (3-POSITION)
ACCESSORYTERMINAL(4-POSITION)
PINION EXTENSION CLUTCH ASSEMBLY
INVERTER
MOTOR ASSEMBLY
POWER SWITCH
BREAKER SWITCH
1600 SERIES CLOSER BODY
CONNECTING LINKBUSHING ASSEMBLY
SHOE
SHOE ADJUSTING ROD ASSEMBLY
FOREARMSCREW
MAIN ARM
ADJUSTINGTUBE
MAIN ARM SLIDEUNIT ASSEMBLY
Included with 5710 and 5740 Included with 5730 and 5740
Component Layout
ADA ANSI UL InformationAmericans With Disabilities Act (ADA)These door operators can be installed and adjusted to conform with ADA regulations
ANSI StandardsANSI A1171 ndash These door operators permit door assemblies to conform to the requirements of this specification for buildings and facilities ndash providing accessibility and usability for physically handicapped people
bull ANSI A15619 ndash These products are designed to conform to this specification for power assist and low energy power operated doors
ndash PAS Function is designed to meet or exceed all of the requirements for the Power Assist Door
ndash POR Function is designed to meet or exceed all of the requirements for the Low Energy Power Operated Door
UL Listing Underwriters Laboratories Inc listed for use on
fire and smoke barrier door assemblies when the 120VAC (60Hz) power input is supplied through the normally closed alarm contacts of a compatible UL Listed alarm system or alarm panel
ASSA ABLOY
SLIDE TRACKASSEMBLY
SLIDER
BUFFER STOP
964rdquo HEXDRIVE SOCKET
SCREW
SLIDE ARMTUBE
SLIDE ARMROD
Page 3 Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Note Door must be visible by person operating activation switch(es)
Door OpeningAngle
Dim ldquoArdquo
Up to 110deg
111deg to 180deg
15-12 (394)
13-14 (337)
Notesbull All dimensions are given in inches (mm)bull Thickness recommended for reinforcements in hollow
metal doors and frames is charted on Page 2bull Do not scale drawingbull Right hand door shownbull This template information based upon use of 5
(127mm) maximum width butt hinges A separate template is required for other conditions
bull Maximum frame reveal is 6-78rdquo (175mm) for this application
bull Conduit hole nearest the hinge is suggested for 120 VAC power input
2rdquo (51mm) Min
Frame Face
1-18rdquo(29)
1-14(32)
1-716(37)
11(279)
22(559)
7-916(192)
13-716(341)
1-18(29)
CL Hinge
14-20 Machine Screwsor No 14 Wood Screws
(6 Places)78 (23) Dia(2 Places)
38 DiaSex Nuts(3 Places)
FrameRabbet
FrameStopSoffit
3(76)
13-1316(350)
12(13)
A
11-1116(297)
6rdquo (152mm)
MinClearance
14-316(360)
12-1516(329)
13-1316(351)
Right Hand Dooropening to 110deg shown
58(159)
Stop
1 Hinge (Pull) Side Mounting Instructions
Step 1 Determine hand of door from illustration on upper right of this page
Step 2 Using template above locate and prepare holes in the frame amp door
FrameA Prepare six (6) holes for 14-20 machine screws or
No 14 x 2-34 (70mm) wood screws Blind rivet nuts (by others) are suggested for unreinforced hollow metal frames or for aluminum frames
B Concealed Wired Units Only Two (2) 78 (22mm) diameter holes for conduit for power input and for switchsensor wires
NOTE On new construction these holes will generally be drilled by the frame supplier at their shop or at the time the frame is installed in the wall
DoorC Prepare three (3) holes for 38 diameter sex nuts Standard units
are supplied with sex nuts and screws for 1-34 (44mm) thick door Sex nuts and screws for other door thicknesses are available to order
Step 3 Remove cover from the unit and set cover amp cover screws aside
Step 4 Mount unit to door frame Select A or B below
A Concealed Wired Units Only
B Surface Wired Units Only
(Continue to next page)
Connect conduit to frame side of backplate Fasten unit to door frame (seven screws)
Fasten unit to door frame (seven screws) Mount conduit bracket (found in screw pack) to unitrsquos backplate with two screws provided Connect wiring conduit to bracket
1A Installation Sequence
LeftHandDoor
RightHandDoor
2rdquo (51mm)Min Frame
FaceFrame Reveal
Do
or
6rdquo (152mm)Min CeilingClearance
1-34rdquo (44mm) Min2-14rdquo (57mm) Max
Door Thickness
Please verify desired mounting requires Hinge (Pull) Side
application as shown on this template
Page 4
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
1A Installation Sequence ContinuedStep 5 Mount track assembly to door using 3 14-20 screws amp sex nuts
with buffer assembly toward hinge Open part of track to face top of door
Step 6 Insert slide arm rod into slide arm tube setting the distance between the pinion square and the slide stud at 13-12rdquo (343) Install 964rdquo hex drive socket head screw from screw pack (See illustration below)
Step 7 Using an adjustable wrench rotate pinion 45deg toward hinge as shown below With the arm assembly parallel to the door secure arm to pinion when square of the pinion aligns with the square in the arm Secure with countersunk washer and 14-20 Flat Head Screw (with thread lock) provided Tighten screw with 716rdquo wrench or socket
Step 9to
increase door closing power Door control is shipped set at midpoint of power setting Maximum closing power can be achieved with 8 (360deg) clockwise turns of the power adjustment screw
Step 8 Insert arm stud into slide block in track assembly Secure by pushing in on the retainer clip that extends from the slide block in the track until it is flush with the slide block (see illustration below)
Adjust closing power of unit (See Fig 1) - Using a 18rdquo allen wrench turn the power adjustment shaft clockwise
Step 10 Adjust Hydraulic valves using a 18rdquo hex wrench to obtain proper door closing speeds See following illustrations Refer to Table 1 below for recommended minimum opening closing times per ANSIBHMA A15619
Note ADA requires that from an open position of 70deg the door will take at least 3 seconds to move to a point 3rdquo (75mm) from the latched position measured at the leading edge of the door
Closing Cycle ndash Make adjustments as necessary to the Sweep Speed S valve and Latch Speed L valve See Fig 2 below for location of valves Turn valves clockwise to reduce speed counter clockwise to increase speed
Opening Cycle ndash Adjust Backcheck B valve as necessary for hydraulic resistance to door opening in the backcheck range See illustration in Fig 2 for location of valve
NOTE Too much Backcheck B valve can affect the operation of the units pump preventing units from fully opening the door This valve may require fine tuning after all other adjustments have been made
2
1Attaching Arm Stud to Slide
Retainer Clip
18HexKey
SlowerClosing
FasterClosingClosing Cycle
Closed
10deg
egnaR hctaL
egnaR peewS
18HexKey
IncreaseCushion
DecreaseCushion
Sweep Valve
Latch Valve
BackcheckValve
Figure 2
Power Adjustment
18HexKey
IncreasePower
DecreasePower Figure 1
Opening Cycle
Backcheckgninep
O
13-12(343)
Note Center threaded hole of slider arm should align with seventh hole of the slider tube Stud in slider arm should point to same side as holes in slider tube (see illustration on Page 3)
RHDoor
LHDoor
RotatePinion
Pinion Flats
1A Installation Sequence ContinuedTable 1 - Minimum Opening Closing Times for ANSIBHMA A15619Door Weight in Pounds (kg)Door Leaf
Width -Inches (mm)
Matrix values are in seconds
Backcheck - adjust the backcheck valve to have a minimum opening time to backcheck or 80 degrees (whichever comes first) based on Table 1
Closing Time - adjust Latch and Sweep valves to have a minimum closing time from 90 degrees to Latch Check or 10 degrees (whichever comes first) based on Table 1
Page 5
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Door OpeningAngle
Dim ldquoArdquo Dim ldquoBrdquo
Up to 110deg
111deg to 170deg
12 (305)
9-12 (241) 13-14 (337)
15-34 (400)
Notesbull All dimensions are given in inches (mm)bull Thickness recommended for reinforcements in
hollow metal doors and frames is charted at the left of this page
bull Do not scale drawingbull Left hand door shownbull This template information based upon use of 5
(127mm) maximum width butt hinges or 34 (19mm) offset pivots A separate template will be supplied for other conditions
bull Maximum frame reveal is 7rdquo (178mm) for this application
bull Conduit hole nearest to hinge is suggested for 120 VAC power input
1-1116(43)
1-14(32)
1116(175)
1-34(44)
12-1516(329)
7-916(192)
13-716(341)
38(10)
CL Hinge or Pivot
14-20 Machine Screwsor No 14 Wood Screws
(6 Places)
78(22)
(Conduit Holes - 2 Places)
Dia
FrameRabbet
FrameStopSoffit
A
13-1316(351)
12(13)
B
5-14rdquoMin
Clearance
11-1116(297)
38(19)
14-316(360)
13-1316(351)
Left Hand Dooropen to 110deg shown
58(159)
Stop
Sex Nuts(2 Places)
2 Stop (Push) Side Mounting Instructions
2A Installation Sequence
LeftHandDoor
RightHandDoor
1-12rdquo (38mm)Min Frame Face
Frame Reveal
Do
or
5-14rdquo (133mm)Min CeilingClearance
1-34rdquo (44mm) Min2-14rdquo (57mm) Max
Door ThicknessFor frame reveals less than 3 (76mm) the arm adjusting rod can be field cut to a length of 9-12 (241mm) measured from centerline of connecting link bushing assembly Note Door must be visible by person operating activation switch(es)
Step 1 Determine hand of door from illustration on upper right of this page
Step 2 Using template above locate and prepare holes in the frame amp door
FrameA Prepare six (6) holes for 14-20 machine screws or No 14 x 2-34
(70mm) wood screws Blind rivet nuts (by others) are suggested for unreinforced hollow metal frames or for aluminum frames
B Concealed Wired Units Only Two (2) 78 (22mm) diameter holes for conduit for power input and for switchsensor wires
NOTE On new construction these holes will generally be drilled by the frame supplier at their shop or at the time the frame is installed in the wall
DoorC Prepare two (2) holes for 38 diameter sex nuts Standard units
are supplied with sex nuts and screws for 1-34 (44mm) thick door Sex nuts and screws for other door thicknesses are available to order
Step 3 Remove cover from the unit and set cover amp cover screws aside
Step 4 Mount unit to door frame Select A or B below
A Concealed Wired Units Only
B Surface Wired Units Only
Connect conduit to frame side of backplate Fasten unit to door frame (six screws)
Fasten unit to door frame (six screws) Mount conduit bracket (found in screw pack) to unit backplate with two screws provided Connect wiring conduit to bracket
Please verify desired mounting requires Stop (Push) Side
application as shown on this template
Page 6
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
2A Installation Sequence Continued
Step 5 Install main arm onto pinion shaft of unit at a 90deg angle to the door frame Align arm mark ldquoSrdquo with the flat corner of the pinion shaft square (See Fig 3 below)
Step 6 Secure main arm to pinion with 14-20 Flange Head Screw provided Tighten screw with 716 wrench or socket
Step 9to
increase door closing power Door control is shipped set at midpoint of power setting Maximum closing power can be achieved with 8 (360deg) clockwise turns of the power adjustment screw
Step 7 Mount arm shoe to door using 2 14-20 screws amp sex nuts provided with screw pack
Step 8 PRELOAD ARM (See Fig 4 below) Remove 14-20 hex head screw on adjusting rod and insert adjusting rod into arm slide Reinstall 14-20 screw and leave loose Rotate main arm in direction away from the hinge edge until the adjusting rod and arm slide are perpendicular (at a 90deg angle) to the door frame Tighten the 14-20 hex head screw on the adjusting rod to secure arm in this new position
Adjust closing power of unit (See Fig 5) - Using a 18rdquo allen wrench turn the power adjustment shaft clockwise
Step 10 Adjust Hydraulic valves using a 18rdquo hex wrench to obtain proper door closing speeds See following illustrations Refer to Table 1 on page 5 for recommended minimum opening closing times per ANSIBHMA A15619
Note ADA requires that from an open position of 70deg the door will take at least 3 seconds to move to a point 3rdquo (75mm) from the latched position measured at the leading edge of the door
Step 11 Make wiring connections using Wiring Instructions on Page below and on Page 8
Closing Cycle ndash Make adjustments as necessary to the Sweep Speed S valve and Latch Speed L valve See Fig 6 below for location of valves Turn valves clockwise to reduce speed counter clockwise to increase speed
Opening Cycle ndash Adjust Backcheck B valve as necessary for hydraulic resistance to door opening in the backcheck range See illustration at bottom of this page for location of valve
NOTE Too much Backcheck B valve can affect the operation of the units pump preventing units from fully opening the door This valve may require fine tuning after all other adjustments have been made
R
LYS
Z
Arm Mark Pinion Flat
Figure 3
AdjustingRod
ArmSlide
DoorShoe
MainArm
Figure 4Adjusting
Rod
ArmSlide
DoorShoe
MainArm
PowerAdjustment
18HexKey
IncreasePower
DecreasePower
Figure 5
18HexKey
SlowerClosing
FasterClosing Closing Cycle
Closed
10deg
egnaR hctaL
egnaR peewS
18HexKey
IncreaseCushion
DecreaseCushion
Opening Cycle
Backcheckgninep
O
Sweep ValveLatch Valve
BackcheckValve
Figure 8
Page 7
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Low VoltageControlWiring
IncomingPower
Optional Bracket(for surface wiring)
GroundLead
PowerLeads
GroundScrew(Green)
CableClamps Conduit
by Others(from top)
ldquoT1rdquo PowerInputTerminal
24
23
22
25
HOT
COM
Breaker Switch
T1 TerminalBlock
4 Final Electrical and Mechanical SetupA Confirm all mechanical adjustments have been made
and wiring connected per Page 7 and 8B Turn on facilityrsquos main circuit breakerC Turn power to unit on at the Unit Power Switch and
turn the Breaker Switch to ldquoRESETrdquo
D Using a short jumper cable jump terminals 1 and 2 see Fig 2 below to activate unit When door reaches 20deg switch Breaker Switch to ldquoOFFrdquo position cutting power to the unit Allow door to fully close (door may be manually pulled closed)
1234
1234
Figure 2
3 Input Power ConfigurationsCONCEALED WIRING SURFACE WIRING
Ground Wire Connection ndash Ground wire must be secured to backplate under head of (green) ground screw
Terminal Description
HOT
25
23
24
22
COM Common power lead
Hot power lead
Circuit Breaker
Switch
Circuit Breaker
Common connection to Circuit Breaker Inverter
Thread conduit fitting(s) into backplate as shown A second conduit fitting is required for low voltage control wiring CHECK LOCAL CODES Pull conduit out of header and attach to conduit fittings before mounting Secure operator to door frame Attach incoming ground wire to backplate with ground screw as illustrated in ldquoSurface Wiringrdquo illustration to the Right
Thread conduit fitting(s) into backplate as shown A second conduit fitting is required for low voltage control wiring CHECK LOCAL CODES Pull conduit out of header and attach to conduit fittings before mounting Secure operator to door frame Attach incoming ground wire to backplate with ground screw as illustrated below
Breaker Switch
Unit Power Switch
Page 8
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
4 Final Electrical and Mechanical Setup ContinuedE Adjust Closing Position Magnet (See Fig 3) - With
door in the closed position use finger to slide Closed Position Magnet so it aligns directly with the Reed Switch
F Adjust Open Position Magnet - Use fingers to slide
F cont Open Position Magnet 180deg from Open Position Magnet
G Flip Breaker Switch to ldquoRESETrdquo to turn power on Jump terminals 1 and 2 (as shown in Fig 2) to activate door Note open position of the door Allow door to close
H Use finger to readjust the Open Position Magnet to desired door open position
I Repeat Step G to verify door open position J Make all connections necessary for any accessories to
the 4-position Accessory Terminal (see Pages 10-11)K Make necessary adjustments to inverter (see Page 9)
Replace cover and cover screws
Reed Switch
Closed Position Magnet
Open PositionMagnet
Position Ring
Figure 3
Inverter Adjustmentsmiddot Based on function
adjustment desired use table above to determine which POT is to be adjusted
POT FUNCTIONDESCRIPTION
OBSTR SENS Obstruction Detection on Open CW - IncreaseCCW - Decrease
MDLY Motor Delay on Opening CW - IncreaseCCW - Decrease
P1 Closing Speed CW - IncreaseCCW - Decrease
HO TM Hold Open Time (5 - 30 Seconds) CW - IncreaseCCW - Decrease
P2 Opening Speed CW - IncreaseCCW - Decrease
HO TQMotor Torque at Hold Open Position
CW - IncreaseCCW - Decrease
ON
12
WARNING
120 HIGH VOLT POTENTIAL PRESENT MAKE SURE POWER IS TURNED OFF DURING
INSTALLATION PROCEDURE
Dip Switch Settings
1 Door Mounting -
2 Push Recognition -
ON - pullOFF - pushON - activeOFF - inactive
WARNINGElectric
Shock Risk
(Adjustments made in the shaded area should be performed by
Authorized Factory Personnel)
L2115Y
L1 115230VAC IN
MOTOR OUT
L2230Y
U
V
W
STATUS LEDS
HO TQHO TM
OBSTRSENS
P1
MDLY P2
16
COM
SNS
COM
PB
K1
K2
11
JMP503
NC
NO
TB501
PU
LL P
US
HSW501
ON
12
Inverter Details
Page 9
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Standard Function with Switches
1
2
3
4
1
2
3
4
Notes1Power input to Door
Operator Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
Wall Switch CardReader Key Switchetc
1
2
3
4
1
2
3
4Door 1 Door 2
Operationbull bull Activating either switch will
open both doors Door will close after hold open time delay has elapsed
Doors are normally closed
Wall Switch CardReader Key Switchetc
Normally Open Momentary dry contacts
Normally Open Momentary dry contacts
Radio Frequency Function Option
1 2 3 4
1 2 3 4
Optional Door 2
1 2 3 4
1 2 3 4
Door 1
Notes1Power input to Door Operator
Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
2 Radio Frequency Feature can be purchased as a separate kit
Operationbull
closedbull Activating wireless
switch or hand held wireless transmitter will open the door
bull Door will close after hold open delay elapses
Door is normally
120VAC
GroundC
OM
HO
TL N(AC) -V +V ADJ
+
11A 24V Power Supply12-24 VA
CD
CC
OM
NO
NC
Troubleshooting
Jump activation input
Change the setting of the ONOFF switch
Flip Door Mounting Dip Switch to other direction
Remove object
Re-time and re-install arm
Increase spring tension per preceding instructions
Remove object
Fault Possible reasons why RemediesExplanations
The door does not open- The motor does not start
Control switch is set to OFF position
Electrical power is missing the electrical Check power switch
Activation unit does not function- The motor starts Motor is driving in wrong direction
Something jammed beneath the door
Arm has come loose
The door does not close Spring tension too lowArm has come loose Re-time and re-install arm
Something jammed beneath the door
Circuit breaker is set to OFF position Reset circuit breaker to the ON position
Page 10
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Fail Secure Fail Safe Electric Strike Wiring
120VACSupplied byOthers- +
DC or ACOutput
AC
or
DC
Ele
ctric
Str
ike+
-
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating for strike interface 30VDC 1A or 125VAC 5A
Operationbull bull Activating switch will unlock the electric strike
and the door will automatically open Door will close after hold open time delay has elapsed
bull For Fail Secure Strike - The door will remain locked during power failure
bull For Fail Safe Strike - The door will remain unlocked during power failure
Door is normally closed and latched
1
2
3
4
1
2
3
4
JMP503
NC
NO
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
Fail Safe Electromagnetic Lock 24VDC Wiring
1
2
3
4
1
2
3
4
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
+-24VDC Electromagnetic Lock(Fail Safe)
Operationbull bull Activating switch will cut power to mag lock and the door will automatically
open Door will close after hold open time delay has elapsedbull The door will unlock during power failure
Door is normally closed and latched
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating 30VDC 1A or 125VAC 5A
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
JMP503
NC
NO
120VAC
GroundC
OM
HO
T
L N(AC) -V +V ADJ+
Optional 11A 24V Power Supply
Page 11
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Page 12
Troubleshooting
Red LEDBlue LED
Antenna Wire
Learnwo DelayButton
DelayPotentiometer(Time Adjustment)
Learn wDelay Button
DIP Switch
TerminalStrip
Problem The LED on my receiver is just flickering and Irsquom unable to program andor it wonrsquot workSolution You have a push plate stuck or faulty transmitter Disconnect each push plate until the LED goes out If LED
does not go out remove each transmitter battery until it does Replace the appropriate transmitterProblem Receiver intermittently doesnrsquot receive the transmitter(s) signal
Solution You may extend the receiver antenna wire only in multiples of 6-34rdquo (171) ie 675 x 4 = 27rdquo (686) of extended antenna wire
Removing Transmitter Code(s)
Single Transmitter CodeŸ Press both Delay and No Delay Buttons simultaneously until Red LED flashes once (approximately 1 second)Ÿ Press transmitter button twice within 10 seconds and the transmitter code will be deleted
All Transmitter CodesŸ Press and hold both Delay and No Delay Buttons simultaneously until Blue LED illuminates then release (approximately 10
seconds)
Push Plate Configuration
1 Before beginning it is easiest to have already prepared the installation of the push plate2 Connect the wires from the transmitter to the NO and COM contacts of the push platersquos switch3 Follow Steps 1 - 4 (Hand-Held Configuration) depress the push plate to activate the transmitter4 Attach the transmitter to the inside of the electrical box and complete the installation
Hand-Held Configuration
1 Set dip switches to the receiver to the desired activation cycle (dip switch 1 - Toggle or Pulse and dip switch 2 - 05s or 10s hold
2 Press either Learn w Delay Button or Learn wo Delay Button on the receiver depending on the activation requirements (if delay learn is selected adjust potentiometer to counterclockwise limit 0 second delay) Red LED on receiver will flash After learn cycle is complete adjust potentiometer to desired delay time (0 - 30 sec)
3 Depress transmitter button repeatedly until Blue LED on the receiver illuminates (indicating reception of signal from transmitter) NOTE Repeat Steps 2 - 3 to program additional transmitters
4 To test the system depress transmitter button (Red LED on Transmitter will illuminate) and observe that the Blue LED illuminates on the receiver This indicates that the relay has been activated
433MHz Receiver Userrsquos Guide
2OFFON
Description05s Hold Time10s Hold Time
FunctionRelay will remain active 05 sec after loss of activationRelay will remain active 10 sec after loss of activation
1OFF
ON
DescriptionPulse Relay
Toggle Relay
FunctionPress the transmitter once and the relay will be active momentarilyPress the transmitter once and the relay output is active indefinitely press it again and the relay will de-energize indefinitely
ON
1 2PU
L T
OG
05s
1
0s ON
1 2PU
L T
OG
05s
1
0sIn Toggle Setting (1-ON) the Hold Time is inactive Either setting for 2 dip switch will
have the same result
ON
1 2PU
L T
OG
05s
1
0s
05 second Pulse Setting
ON
1 2PU
L T
OG
05s
1
0s
10 second Pulse Setting
ŸAlways stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door
ŸEnsure compliance with all applicable safety standards upon completion of installation
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
This PageLeft Blank
Page 13
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Hinge (Pull) SideŸ Do not scale drawingŸ Right hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
No
te D
oo
r m
ust
be
visi
ble
by
per
son
o
per
atin
g a
ctiv
atio
n s
wit
ch(e
s)
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Up
to 1
10deg
111deg
to 1
80deg
15-1
2 (
394)
13-1
4 (
337)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull T
hick
ness
rec
omm
ende
d fo
r re
info
rcem
ents
in h
ollo
w
met
al d
oors
and
fram
es is
cha
rted
on
Pag
e 2
bull D
o no
t sca
le d
raw
ing
bull R
ight
han
d do
or s
how
nbull
Thi
s te
mpl
ate
info
rmat
ion
base
d up
on u
se o
f 5
(127
mm
) m
axim
um w
idth
but
t hin
ges
A s
epar
ate
tem
plat
e is
req
uire
d fo
r ot
her
cond
ition
sbull
Max
imum
fram
e re
veal
is 6
-78
rdquo (17
5mm
) fo
r th
is
appl
icat
ion
bull C
ondu
it ho
le n
eare
st th
e hi
nge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
2rdquo (
51m
m)
Min
F
ram
e Fa
ce
1-1
8rdquo(2
9)
1-1
4(3
2)1-
716
(37)
11(2
79)
22(5
59)
7-9
16(1
92)
13-7
16
(341
)
1-1
8(2
9)
C LH
inge
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)7
8 (2
3) D
ia
(2 P
lace
s)
38
Dia
S
ex N
uts
(3 P
lace
s)
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
3(7
6)
13-1
316
(350
)
12
(13)
A
11-1
116
(297
)
6rdquo
(152
mm
)M
in
Cle
aran
ce
14-3
16
(360
)
12-1
516
(329
)13
-13
16(3
51)
Rig
ht
Han
d D
oo
ro
pen
ing
to
110
deg sh
ow
n
58
(15
9)S
top
Left
Han
dD
oor
Rig
htH
and
Doo
r
2rdquo (
51m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
6rdquo (
152m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
ax
Do
or T
hic
knes
s
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Hin
ge
(Pu
ll) S
ide
app
licat
ion
as
sho
wn
on
th
is
tem
pla
te
Page 14
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Stop (Push) SideŸ Do not scale drawingŸ Left hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Dim
ldquoB
rdquo
Up
to 1
10deg
111deg
to 1
70deg
12 (
305)
9-1
2 (2
41)
13-1
4 (
337)
15-3
4 (
400)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull Thi
ckne
ss r
ecom
men
ded
for
rein
forc
emen
ts in
ho
llow
met
al d
oors
and
fram
es is
cha
rted
at t
he
left
of th
is p
age
bull D
o no
t sca
le d
raw
ing
bull Le
ft ha
nd d
oor
show
nbull T
his
tem
plat
e in
form
atio
n ba
sed
upon
use
of 5
(1
27m
m)
max
imum
wid
th b
utt h
inge
s or
34
(1
9mm
) of
fset
piv
ots
A s
epar
ate
tem
plat
e w
ill
be s
uppl
ied
for
othe
r co
nditi
ons
bull M
axim
um fr
ame
reve
al is
7rdquo (
178m
m)
for
this
ap
plic
atio
nbull
Con
duit
hole
nea
rest
to h
inge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
1-11
16
(43)
1-1
4(3
2)11
16
(17
5)
1-3
4(4
4)
12-1
516
(329
)
7-9
16(1
92)
13-7
16
(341
)
38
(10)
C LH
inge
or
Piv
ot
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)
78
(22)
(Con
duit
Hol
es -
2
Pla
ces)
Dia
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
A13-1
316
(351
)
12
(13)
B
5-1
4rdquoM
in
Cle
aran
ce
11-1
116
(297
)
38
(19)
14-3
16
(360
)13
-13
16(3
51)
Lef
t H
and
Do
or
op
en t
o 1
10deg
sho
wn
58
(15
9)S
top
Sex
Nu
ts(2
Pla
ces)
Left
Han
dD
oor
Rig
htH
and
Doo
r
1-1
2rdquo (
38m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
5-1
4rdquo (
133m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
axD
oo
r Th
ickn
ess
No
te D
oo
r m
ust
be
visi
ble
by
per
son
op
erat
ing
act
ivat
ion
sw
itch
(es)
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Sto
p (
Pu
sh)
Sid
e ap
plic
atio
n a
s sh
ow
n o
n t
his
te
mp
late
Page 15
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
3000 Highway 74 East bull Monroe NC 28112Tel (800)-438-1951 x4706 bull Fax (800)-338-0965
wwwnor tondoorcontrolscom
ASSA ABLOY
This PageLeft Blank
Page 16
ASSA ABLOY
Page 2
Hollow Metal Door Frame Reinforcing
FrameMaterial
12 Ga1046 (266)
14 Ga0747 (190)
16 Ga0598 (152)
18 Ga0478 (121)
12 Ga1046 (266)
10 Ga1343 (341)
10 Ga1343 (341)
8 Ga1644 (418)
18 Ga0478 (121)
12 Ga1046 (266)
12 Ga1046 (266)
10 Ga1343 (341)
Reinforcing
Recommended Min Required
Contents
General Informationbull
the 120VAC (60Hz) power input to the LEO door operator be supplied through normally closed alarm contacts of the alarm system alarm panel
bull Power input to LEO door operator must be 120VAC (60Hz) to terminals HOT and COM at terminal strip T1 Earth ground (GND) to green screw on backplate
bull All wiring must conform to standard wiring practice in accordance with national and local wiring codes
bull Note Unless otherwise noted all dimensions are given in inches (millimeters)
bull Minimum suggested and required material thickness for hollow metal frames (skin plus reinforcement) is charted on below
bull Unit is Non-Handed
bull Door must be hung on butt hinges [5rdquo (127mm) max width] or 34rdquo (19mm) offset pivots A separate door and frame preparation template will be supplied for other conditions
bull Door must swing freely through the entire opening and closing cycle before beginning the installation
bull Use of an auxiliary door stop (by others) is always recommended
bull An incorrectly installed or improperly adjusted door operator can cause property damage or personal injury These instructions should be followed to avoid the possibility of misapplication or misadjustment
UL labeled fire or smoke barrier door assemblies require that WARNING Make sure 120VAC (60Hz) input power is turned off at facilityrsquos main circuit breaker before proceeding with installation
General Templating Informationbull Before beginning the installation verify that the door frame is
properly reinforced and is well anchored in the wall
bull Unreinforced hollow metal frames and aluminum frames should be prepared and fitted with 14-20 blind rivet nuts furnished by others
bull Concealed electrical conduit and concealed switch or sensor wires should be pulled to the frame before proceeding
Fasteners for Framebull 14-20 machine screws for hollow metal and aluminumbull No 14 x 2-34rdquo (70mm) long sheet metal screws for wood
Fasteners for Doorbull 14-20 machine screwsbull 38rdquo diameter x 1-58rdquo (41mm) long sex nut
Electrical Informationbull Maximum current draw of unit is 06 amps
bull Breaker Switch protects the motor assembly and inverter and has a 3 amp rating
bull Maximum wire size is12AWG at terminals HOT and COM (120VAC 60Hz) on ldquoT1rdquo Power Input Terminal14AWG at terminals 1 thru 4 on Accessory Terminal 18AWG at terminals 22 thru 25 on ldquoT1rdquo Power Input Terminal
Frame Reinforcement Table
General 2Frame Reinforcement Table Technical Data 2Component Layout 3ADA ANSI UL 3Hinge (Pull) Side Mounting 4Stop (Push) Side Mounting 6 Adjust Power and Opening Closing Cycle 5 7Input Power Configuration 8
Final Setup 8Inverter Details 9Accessory Typical Installations 10Troubleshooting 10RF Receiver Userrsquos Guide 12Hinge (Pull) Side Template 14Stop (Push) Side Template 15
Technical Data
120VAC 60Hz
6 amps
24 V DC max 11 Amp
28 - 48 (71-122 cm)
100-250 lb (45-113 kg)
Input power
Power consumption
Power supply
Door width
Door weight
Door opening angle
Hold open time 5 - 30 seconds (ADA 5 seconds min)
3 ampsCircuit breaker
up to 110deg Pull side up to 170 Push sideManually to 180deg PushPull side
deg
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
BACKPLATE
REED SWITCH
CHAINOPEN CLOSE POSITIONING MAGNETS
ldquoT1rdquo POWER INPUTTERMINAL (3-POSITION)
ACCESSORYTERMINAL(4-POSITION)
PINION EXTENSION CLUTCH ASSEMBLY
INVERTER
MOTOR ASSEMBLY
POWER SWITCH
BREAKER SWITCH
1600 SERIES CLOSER BODY
CONNECTING LINKBUSHING ASSEMBLY
SHOE
SHOE ADJUSTING ROD ASSEMBLY
FOREARMSCREW
MAIN ARM
ADJUSTINGTUBE
MAIN ARM SLIDEUNIT ASSEMBLY
Included with 5710 and 5740 Included with 5730 and 5740
Component Layout
ADA ANSI UL InformationAmericans With Disabilities Act (ADA)These door operators can be installed and adjusted to conform with ADA regulations
ANSI StandardsANSI A1171 ndash These door operators permit door assemblies to conform to the requirements of this specification for buildings and facilities ndash providing accessibility and usability for physically handicapped people
bull ANSI A15619 ndash These products are designed to conform to this specification for power assist and low energy power operated doors
ndash PAS Function is designed to meet or exceed all of the requirements for the Power Assist Door
ndash POR Function is designed to meet or exceed all of the requirements for the Low Energy Power Operated Door
UL Listing Underwriters Laboratories Inc listed for use on
fire and smoke barrier door assemblies when the 120VAC (60Hz) power input is supplied through the normally closed alarm contacts of a compatible UL Listed alarm system or alarm panel
ASSA ABLOY
SLIDE TRACKASSEMBLY
SLIDER
BUFFER STOP
964rdquo HEXDRIVE SOCKET
SCREW
SLIDE ARMTUBE
SLIDE ARMROD
Page 3 Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Note Door must be visible by person operating activation switch(es)
Door OpeningAngle
Dim ldquoArdquo
Up to 110deg
111deg to 180deg
15-12 (394)
13-14 (337)
Notesbull All dimensions are given in inches (mm)bull Thickness recommended for reinforcements in hollow
metal doors and frames is charted on Page 2bull Do not scale drawingbull Right hand door shownbull This template information based upon use of 5
(127mm) maximum width butt hinges A separate template is required for other conditions
bull Maximum frame reveal is 6-78rdquo (175mm) for this application
bull Conduit hole nearest the hinge is suggested for 120 VAC power input
2rdquo (51mm) Min
Frame Face
1-18rdquo(29)
1-14(32)
1-716(37)
11(279)
22(559)
7-916(192)
13-716(341)
1-18(29)
CL Hinge
14-20 Machine Screwsor No 14 Wood Screws
(6 Places)78 (23) Dia(2 Places)
38 DiaSex Nuts(3 Places)
FrameRabbet
FrameStopSoffit
3(76)
13-1316(350)
12(13)
A
11-1116(297)
6rdquo (152mm)
MinClearance
14-316(360)
12-1516(329)
13-1316(351)
Right Hand Dooropening to 110deg shown
58(159)
Stop
1 Hinge (Pull) Side Mounting Instructions
Step 1 Determine hand of door from illustration on upper right of this page
Step 2 Using template above locate and prepare holes in the frame amp door
FrameA Prepare six (6) holes for 14-20 machine screws or
No 14 x 2-34 (70mm) wood screws Blind rivet nuts (by others) are suggested for unreinforced hollow metal frames or for aluminum frames
B Concealed Wired Units Only Two (2) 78 (22mm) diameter holes for conduit for power input and for switchsensor wires
NOTE On new construction these holes will generally be drilled by the frame supplier at their shop or at the time the frame is installed in the wall
DoorC Prepare three (3) holes for 38 diameter sex nuts Standard units
are supplied with sex nuts and screws for 1-34 (44mm) thick door Sex nuts and screws for other door thicknesses are available to order
Step 3 Remove cover from the unit and set cover amp cover screws aside
Step 4 Mount unit to door frame Select A or B below
A Concealed Wired Units Only
B Surface Wired Units Only
(Continue to next page)
Connect conduit to frame side of backplate Fasten unit to door frame (seven screws)
Fasten unit to door frame (seven screws) Mount conduit bracket (found in screw pack) to unitrsquos backplate with two screws provided Connect wiring conduit to bracket
1A Installation Sequence
LeftHandDoor
RightHandDoor
2rdquo (51mm)Min Frame
FaceFrame Reveal
Do
or
6rdquo (152mm)Min CeilingClearance
1-34rdquo (44mm) Min2-14rdquo (57mm) Max
Door Thickness
Please verify desired mounting requires Hinge (Pull) Side
application as shown on this template
Page 4
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
1A Installation Sequence ContinuedStep 5 Mount track assembly to door using 3 14-20 screws amp sex nuts
with buffer assembly toward hinge Open part of track to face top of door
Step 6 Insert slide arm rod into slide arm tube setting the distance between the pinion square and the slide stud at 13-12rdquo (343) Install 964rdquo hex drive socket head screw from screw pack (See illustration below)
Step 7 Using an adjustable wrench rotate pinion 45deg toward hinge as shown below With the arm assembly parallel to the door secure arm to pinion when square of the pinion aligns with the square in the arm Secure with countersunk washer and 14-20 Flat Head Screw (with thread lock) provided Tighten screw with 716rdquo wrench or socket
Step 9to
increase door closing power Door control is shipped set at midpoint of power setting Maximum closing power can be achieved with 8 (360deg) clockwise turns of the power adjustment screw
Step 8 Insert arm stud into slide block in track assembly Secure by pushing in on the retainer clip that extends from the slide block in the track until it is flush with the slide block (see illustration below)
Adjust closing power of unit (See Fig 1) - Using a 18rdquo allen wrench turn the power adjustment shaft clockwise
Step 10 Adjust Hydraulic valves using a 18rdquo hex wrench to obtain proper door closing speeds See following illustrations Refer to Table 1 below for recommended minimum opening closing times per ANSIBHMA A15619
Note ADA requires that from an open position of 70deg the door will take at least 3 seconds to move to a point 3rdquo (75mm) from the latched position measured at the leading edge of the door
Closing Cycle ndash Make adjustments as necessary to the Sweep Speed S valve and Latch Speed L valve See Fig 2 below for location of valves Turn valves clockwise to reduce speed counter clockwise to increase speed
Opening Cycle ndash Adjust Backcheck B valve as necessary for hydraulic resistance to door opening in the backcheck range See illustration in Fig 2 for location of valve
NOTE Too much Backcheck B valve can affect the operation of the units pump preventing units from fully opening the door This valve may require fine tuning after all other adjustments have been made
2
1Attaching Arm Stud to Slide
Retainer Clip
18HexKey
SlowerClosing
FasterClosingClosing Cycle
Closed
10deg
egnaR hctaL
egnaR peewS
18HexKey
IncreaseCushion
DecreaseCushion
Sweep Valve
Latch Valve
BackcheckValve
Figure 2
Power Adjustment
18HexKey
IncreasePower
DecreasePower Figure 1
Opening Cycle
Backcheckgninep
O
13-12(343)
Note Center threaded hole of slider arm should align with seventh hole of the slider tube Stud in slider arm should point to same side as holes in slider tube (see illustration on Page 3)
RHDoor
LHDoor
RotatePinion
Pinion Flats
1A Installation Sequence ContinuedTable 1 - Minimum Opening Closing Times for ANSIBHMA A15619Door Weight in Pounds (kg)Door Leaf
Width -Inches (mm)
Matrix values are in seconds
Backcheck - adjust the backcheck valve to have a minimum opening time to backcheck or 80 degrees (whichever comes first) based on Table 1
Closing Time - adjust Latch and Sweep valves to have a minimum closing time from 90 degrees to Latch Check or 10 degrees (whichever comes first) based on Table 1
Page 5
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Door OpeningAngle
Dim ldquoArdquo Dim ldquoBrdquo
Up to 110deg
111deg to 170deg
12 (305)
9-12 (241) 13-14 (337)
15-34 (400)
Notesbull All dimensions are given in inches (mm)bull Thickness recommended for reinforcements in
hollow metal doors and frames is charted at the left of this page
bull Do not scale drawingbull Left hand door shownbull This template information based upon use of 5
(127mm) maximum width butt hinges or 34 (19mm) offset pivots A separate template will be supplied for other conditions
bull Maximum frame reveal is 7rdquo (178mm) for this application
bull Conduit hole nearest to hinge is suggested for 120 VAC power input
1-1116(43)
1-14(32)
1116(175)
1-34(44)
12-1516(329)
7-916(192)
13-716(341)
38(10)
CL Hinge or Pivot
14-20 Machine Screwsor No 14 Wood Screws
(6 Places)
78(22)
(Conduit Holes - 2 Places)
Dia
FrameRabbet
FrameStopSoffit
A
13-1316(351)
12(13)
B
5-14rdquoMin
Clearance
11-1116(297)
38(19)
14-316(360)
13-1316(351)
Left Hand Dooropen to 110deg shown
58(159)
Stop
Sex Nuts(2 Places)
2 Stop (Push) Side Mounting Instructions
2A Installation Sequence
LeftHandDoor
RightHandDoor
1-12rdquo (38mm)Min Frame Face
Frame Reveal
Do
or
5-14rdquo (133mm)Min CeilingClearance
1-34rdquo (44mm) Min2-14rdquo (57mm) Max
Door ThicknessFor frame reveals less than 3 (76mm) the arm adjusting rod can be field cut to a length of 9-12 (241mm) measured from centerline of connecting link bushing assembly Note Door must be visible by person operating activation switch(es)
Step 1 Determine hand of door from illustration on upper right of this page
Step 2 Using template above locate and prepare holes in the frame amp door
FrameA Prepare six (6) holes for 14-20 machine screws or No 14 x 2-34
(70mm) wood screws Blind rivet nuts (by others) are suggested for unreinforced hollow metal frames or for aluminum frames
B Concealed Wired Units Only Two (2) 78 (22mm) diameter holes for conduit for power input and for switchsensor wires
NOTE On new construction these holes will generally be drilled by the frame supplier at their shop or at the time the frame is installed in the wall
DoorC Prepare two (2) holes for 38 diameter sex nuts Standard units
are supplied with sex nuts and screws for 1-34 (44mm) thick door Sex nuts and screws for other door thicknesses are available to order
Step 3 Remove cover from the unit and set cover amp cover screws aside
Step 4 Mount unit to door frame Select A or B below
A Concealed Wired Units Only
B Surface Wired Units Only
Connect conduit to frame side of backplate Fasten unit to door frame (six screws)
Fasten unit to door frame (six screws) Mount conduit bracket (found in screw pack) to unit backplate with two screws provided Connect wiring conduit to bracket
Please verify desired mounting requires Stop (Push) Side
application as shown on this template
Page 6
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
2A Installation Sequence Continued
Step 5 Install main arm onto pinion shaft of unit at a 90deg angle to the door frame Align arm mark ldquoSrdquo with the flat corner of the pinion shaft square (See Fig 3 below)
Step 6 Secure main arm to pinion with 14-20 Flange Head Screw provided Tighten screw with 716 wrench or socket
Step 9to
increase door closing power Door control is shipped set at midpoint of power setting Maximum closing power can be achieved with 8 (360deg) clockwise turns of the power adjustment screw
Step 7 Mount arm shoe to door using 2 14-20 screws amp sex nuts provided with screw pack
Step 8 PRELOAD ARM (See Fig 4 below) Remove 14-20 hex head screw on adjusting rod and insert adjusting rod into arm slide Reinstall 14-20 screw and leave loose Rotate main arm in direction away from the hinge edge until the adjusting rod and arm slide are perpendicular (at a 90deg angle) to the door frame Tighten the 14-20 hex head screw on the adjusting rod to secure arm in this new position
Adjust closing power of unit (See Fig 5) - Using a 18rdquo allen wrench turn the power adjustment shaft clockwise
Step 10 Adjust Hydraulic valves using a 18rdquo hex wrench to obtain proper door closing speeds See following illustrations Refer to Table 1 on page 5 for recommended minimum opening closing times per ANSIBHMA A15619
Note ADA requires that from an open position of 70deg the door will take at least 3 seconds to move to a point 3rdquo (75mm) from the latched position measured at the leading edge of the door
Step 11 Make wiring connections using Wiring Instructions on Page below and on Page 8
Closing Cycle ndash Make adjustments as necessary to the Sweep Speed S valve and Latch Speed L valve See Fig 6 below for location of valves Turn valves clockwise to reduce speed counter clockwise to increase speed
Opening Cycle ndash Adjust Backcheck B valve as necessary for hydraulic resistance to door opening in the backcheck range See illustration at bottom of this page for location of valve
NOTE Too much Backcheck B valve can affect the operation of the units pump preventing units from fully opening the door This valve may require fine tuning after all other adjustments have been made
R
LYS
Z
Arm Mark Pinion Flat
Figure 3
AdjustingRod
ArmSlide
DoorShoe
MainArm
Figure 4Adjusting
Rod
ArmSlide
DoorShoe
MainArm
PowerAdjustment
18HexKey
IncreasePower
DecreasePower
Figure 5
18HexKey
SlowerClosing
FasterClosing Closing Cycle
Closed
10deg
egnaR hctaL
egnaR peewS
18HexKey
IncreaseCushion
DecreaseCushion
Opening Cycle
Backcheckgninep
O
Sweep ValveLatch Valve
BackcheckValve
Figure 8
Page 7
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Low VoltageControlWiring
IncomingPower
Optional Bracket(for surface wiring)
GroundLead
PowerLeads
GroundScrew(Green)
CableClamps Conduit
by Others(from top)
ldquoT1rdquo PowerInputTerminal
24
23
22
25
HOT
COM
Breaker Switch
T1 TerminalBlock
4 Final Electrical and Mechanical SetupA Confirm all mechanical adjustments have been made
and wiring connected per Page 7 and 8B Turn on facilityrsquos main circuit breakerC Turn power to unit on at the Unit Power Switch and
turn the Breaker Switch to ldquoRESETrdquo
D Using a short jumper cable jump terminals 1 and 2 see Fig 2 below to activate unit When door reaches 20deg switch Breaker Switch to ldquoOFFrdquo position cutting power to the unit Allow door to fully close (door may be manually pulled closed)
1234
1234
Figure 2
3 Input Power ConfigurationsCONCEALED WIRING SURFACE WIRING
Ground Wire Connection ndash Ground wire must be secured to backplate under head of (green) ground screw
Terminal Description
HOT
25
23
24
22
COM Common power lead
Hot power lead
Circuit Breaker
Switch
Circuit Breaker
Common connection to Circuit Breaker Inverter
Thread conduit fitting(s) into backplate as shown A second conduit fitting is required for low voltage control wiring CHECK LOCAL CODES Pull conduit out of header and attach to conduit fittings before mounting Secure operator to door frame Attach incoming ground wire to backplate with ground screw as illustrated in ldquoSurface Wiringrdquo illustration to the Right
Thread conduit fitting(s) into backplate as shown A second conduit fitting is required for low voltage control wiring CHECK LOCAL CODES Pull conduit out of header and attach to conduit fittings before mounting Secure operator to door frame Attach incoming ground wire to backplate with ground screw as illustrated below
Breaker Switch
Unit Power Switch
Page 8
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
4 Final Electrical and Mechanical Setup ContinuedE Adjust Closing Position Magnet (See Fig 3) - With
door in the closed position use finger to slide Closed Position Magnet so it aligns directly with the Reed Switch
F Adjust Open Position Magnet - Use fingers to slide
F cont Open Position Magnet 180deg from Open Position Magnet
G Flip Breaker Switch to ldquoRESETrdquo to turn power on Jump terminals 1 and 2 (as shown in Fig 2) to activate door Note open position of the door Allow door to close
H Use finger to readjust the Open Position Magnet to desired door open position
I Repeat Step G to verify door open position J Make all connections necessary for any accessories to
the 4-position Accessory Terminal (see Pages 10-11)K Make necessary adjustments to inverter (see Page 9)
Replace cover and cover screws
Reed Switch
Closed Position Magnet
Open PositionMagnet
Position Ring
Figure 3
Inverter Adjustmentsmiddot Based on function
adjustment desired use table above to determine which POT is to be adjusted
POT FUNCTIONDESCRIPTION
OBSTR SENS Obstruction Detection on Open CW - IncreaseCCW - Decrease
MDLY Motor Delay on Opening CW - IncreaseCCW - Decrease
P1 Closing Speed CW - IncreaseCCW - Decrease
HO TM Hold Open Time (5 - 30 Seconds) CW - IncreaseCCW - Decrease
P2 Opening Speed CW - IncreaseCCW - Decrease
HO TQMotor Torque at Hold Open Position
CW - IncreaseCCW - Decrease
ON
12
WARNING
120 HIGH VOLT POTENTIAL PRESENT MAKE SURE POWER IS TURNED OFF DURING
INSTALLATION PROCEDURE
Dip Switch Settings
1 Door Mounting -
2 Push Recognition -
ON - pullOFF - pushON - activeOFF - inactive
WARNINGElectric
Shock Risk
(Adjustments made in the shaded area should be performed by
Authorized Factory Personnel)
L2115Y
L1 115230VAC IN
MOTOR OUT
L2230Y
U
V
W
STATUS LEDS
HO TQHO TM
OBSTRSENS
P1
MDLY P2
16
COM
SNS
COM
PB
K1
K2
11
JMP503
NC
NO
TB501
PU
LL P
US
HSW501
ON
12
Inverter Details
Page 9
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Standard Function with Switches
1
2
3
4
1
2
3
4
Notes1Power input to Door
Operator Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
Wall Switch CardReader Key Switchetc
1
2
3
4
1
2
3
4Door 1 Door 2
Operationbull bull Activating either switch will
open both doors Door will close after hold open time delay has elapsed
Doors are normally closed
Wall Switch CardReader Key Switchetc
Normally Open Momentary dry contacts
Normally Open Momentary dry contacts
Radio Frequency Function Option
1 2 3 4
1 2 3 4
Optional Door 2
1 2 3 4
1 2 3 4
Door 1
Notes1Power input to Door Operator
Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
2 Radio Frequency Feature can be purchased as a separate kit
Operationbull
closedbull Activating wireless
switch or hand held wireless transmitter will open the door
bull Door will close after hold open delay elapses
Door is normally
120VAC
GroundC
OM
HO
TL N(AC) -V +V ADJ
+
11A 24V Power Supply12-24 VA
CD
CC
OM
NO
NC
Troubleshooting
Jump activation input
Change the setting of the ONOFF switch
Flip Door Mounting Dip Switch to other direction
Remove object
Re-time and re-install arm
Increase spring tension per preceding instructions
Remove object
Fault Possible reasons why RemediesExplanations
The door does not open- The motor does not start
Control switch is set to OFF position
Electrical power is missing the electrical Check power switch
Activation unit does not function- The motor starts Motor is driving in wrong direction
Something jammed beneath the door
Arm has come loose
The door does not close Spring tension too lowArm has come loose Re-time and re-install arm
Something jammed beneath the door
Circuit breaker is set to OFF position Reset circuit breaker to the ON position
Page 10
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Fail Secure Fail Safe Electric Strike Wiring
120VACSupplied byOthers- +
DC or ACOutput
AC
or
DC
Ele
ctric
Str
ike+
-
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating for strike interface 30VDC 1A or 125VAC 5A
Operationbull bull Activating switch will unlock the electric strike
and the door will automatically open Door will close after hold open time delay has elapsed
bull For Fail Secure Strike - The door will remain locked during power failure
bull For Fail Safe Strike - The door will remain unlocked during power failure
Door is normally closed and latched
1
2
3
4
1
2
3
4
JMP503
NC
NO
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
Fail Safe Electromagnetic Lock 24VDC Wiring
1
2
3
4
1
2
3
4
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
+-24VDC Electromagnetic Lock(Fail Safe)
Operationbull bull Activating switch will cut power to mag lock and the door will automatically
open Door will close after hold open time delay has elapsedbull The door will unlock during power failure
Door is normally closed and latched
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating 30VDC 1A or 125VAC 5A
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
JMP503
NC
NO
120VAC
GroundC
OM
HO
T
L N(AC) -V +V ADJ+
Optional 11A 24V Power Supply
Page 11
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Page 12
Troubleshooting
Red LEDBlue LED
Antenna Wire
Learnwo DelayButton
DelayPotentiometer(Time Adjustment)
Learn wDelay Button
DIP Switch
TerminalStrip
Problem The LED on my receiver is just flickering and Irsquom unable to program andor it wonrsquot workSolution You have a push plate stuck or faulty transmitter Disconnect each push plate until the LED goes out If LED
does not go out remove each transmitter battery until it does Replace the appropriate transmitterProblem Receiver intermittently doesnrsquot receive the transmitter(s) signal
Solution You may extend the receiver antenna wire only in multiples of 6-34rdquo (171) ie 675 x 4 = 27rdquo (686) of extended antenna wire
Removing Transmitter Code(s)
Single Transmitter CodeŸ Press both Delay and No Delay Buttons simultaneously until Red LED flashes once (approximately 1 second)Ÿ Press transmitter button twice within 10 seconds and the transmitter code will be deleted
All Transmitter CodesŸ Press and hold both Delay and No Delay Buttons simultaneously until Blue LED illuminates then release (approximately 10
seconds)
Push Plate Configuration
1 Before beginning it is easiest to have already prepared the installation of the push plate2 Connect the wires from the transmitter to the NO and COM contacts of the push platersquos switch3 Follow Steps 1 - 4 (Hand-Held Configuration) depress the push plate to activate the transmitter4 Attach the transmitter to the inside of the electrical box and complete the installation
Hand-Held Configuration
1 Set dip switches to the receiver to the desired activation cycle (dip switch 1 - Toggle or Pulse and dip switch 2 - 05s or 10s hold
2 Press either Learn w Delay Button or Learn wo Delay Button on the receiver depending on the activation requirements (if delay learn is selected adjust potentiometer to counterclockwise limit 0 second delay) Red LED on receiver will flash After learn cycle is complete adjust potentiometer to desired delay time (0 - 30 sec)
3 Depress transmitter button repeatedly until Blue LED on the receiver illuminates (indicating reception of signal from transmitter) NOTE Repeat Steps 2 - 3 to program additional transmitters
4 To test the system depress transmitter button (Red LED on Transmitter will illuminate) and observe that the Blue LED illuminates on the receiver This indicates that the relay has been activated
433MHz Receiver Userrsquos Guide
2OFFON
Description05s Hold Time10s Hold Time
FunctionRelay will remain active 05 sec after loss of activationRelay will remain active 10 sec after loss of activation
1OFF
ON
DescriptionPulse Relay
Toggle Relay
FunctionPress the transmitter once and the relay will be active momentarilyPress the transmitter once and the relay output is active indefinitely press it again and the relay will de-energize indefinitely
ON
1 2PU
L T
OG
05s
1
0s ON
1 2PU
L T
OG
05s
1
0sIn Toggle Setting (1-ON) the Hold Time is inactive Either setting for 2 dip switch will
have the same result
ON
1 2PU
L T
OG
05s
1
0s
05 second Pulse Setting
ON
1 2PU
L T
OG
05s
1
0s
10 second Pulse Setting
ŸAlways stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door
ŸEnsure compliance with all applicable safety standards upon completion of installation
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
This PageLeft Blank
Page 13
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Hinge (Pull) SideŸ Do not scale drawingŸ Right hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
No
te D
oo
r m
ust
be
visi
ble
by
per
son
o
per
atin
g a
ctiv
atio
n s
wit
ch(e
s)
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Up
to 1
10deg
111deg
to 1
80deg
15-1
2 (
394)
13-1
4 (
337)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull T
hick
ness
rec
omm
ende
d fo
r re
info
rcem
ents
in h
ollo
w
met
al d
oors
and
fram
es is
cha
rted
on
Pag
e 2
bull D
o no
t sca
le d
raw
ing
bull R
ight
han
d do
or s
how
nbull
Thi
s te
mpl
ate
info
rmat
ion
base
d up
on u
se o
f 5
(127
mm
) m
axim
um w
idth
but
t hin
ges
A s
epar
ate
tem
plat
e is
req
uire
d fo
r ot
her
cond
ition
sbull
Max
imum
fram
e re
veal
is 6
-78
rdquo (17
5mm
) fo
r th
is
appl
icat
ion
bull C
ondu
it ho
le n
eare
st th
e hi
nge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
2rdquo (
51m
m)
Min
F
ram
e Fa
ce
1-1
8rdquo(2
9)
1-1
4(3
2)1-
716
(37)
11(2
79)
22(5
59)
7-9
16(1
92)
13-7
16
(341
)
1-1
8(2
9)
C LH
inge
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)7
8 (2
3) D
ia
(2 P
lace
s)
38
Dia
S
ex N
uts
(3 P
lace
s)
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
3(7
6)
13-1
316
(350
)
12
(13)
A
11-1
116
(297
)
6rdquo
(152
mm
)M
in
Cle
aran
ce
14-3
16
(360
)
12-1
516
(329
)13
-13
16(3
51)
Rig
ht
Han
d D
oo
ro
pen
ing
to
110
deg sh
ow
n
58
(15
9)S
top
Left
Han
dD
oor
Rig
htH
and
Doo
r
2rdquo (
51m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
6rdquo (
152m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
ax
Do
or T
hic
knes
s
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Hin
ge
(Pu
ll) S
ide
app
licat
ion
as
sho
wn
on
th
is
tem
pla
te
Page 14
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Stop (Push) SideŸ Do not scale drawingŸ Left hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Dim
ldquoB
rdquo
Up
to 1
10deg
111deg
to 1
70deg
12 (
305)
9-1
2 (2
41)
13-1
4 (
337)
15-3
4 (
400)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull Thi
ckne
ss r
ecom
men
ded
for
rein
forc
emen
ts in
ho
llow
met
al d
oors
and
fram
es is
cha
rted
at t
he
left
of th
is p
age
bull D
o no
t sca
le d
raw
ing
bull Le
ft ha
nd d
oor
show
nbull T
his
tem
plat
e in
form
atio
n ba
sed
upon
use
of 5
(1
27m
m)
max
imum
wid
th b
utt h
inge
s or
34
(1
9mm
) of
fset
piv
ots
A s
epar
ate
tem
plat
e w
ill
be s
uppl
ied
for
othe
r co
nditi
ons
bull M
axim
um fr
ame
reve
al is
7rdquo (
178m
m)
for
this
ap
plic
atio
nbull
Con
duit
hole
nea
rest
to h
inge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
1-11
16
(43)
1-1
4(3
2)11
16
(17
5)
1-3
4(4
4)
12-1
516
(329
)
7-9
16(1
92)
13-7
16
(341
)
38
(10)
C LH
inge
or
Piv
ot
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)
78
(22)
(Con
duit
Hol
es -
2
Pla
ces)
Dia
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
A13-1
316
(351
)
12
(13)
B
5-1
4rdquoM
in
Cle
aran
ce
11-1
116
(297
)
38
(19)
14-3
16
(360
)13
-13
16(3
51)
Lef
t H
and
Do
or
op
en t
o 1
10deg
sho
wn
58
(15
9)S
top
Sex
Nu
ts(2
Pla
ces)
Left
Han
dD
oor
Rig
htH
and
Doo
r
1-1
2rdquo (
38m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
5-1
4rdquo (
133m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
axD
oo
r Th
ickn
ess
No
te D
oo
r m
ust
be
visi
ble
by
per
son
op
erat
ing
act
ivat
ion
sw
itch
(es)
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Sto
p (
Pu
sh)
Sid
e ap
plic
atio
n a
s sh
ow
n o
n t
his
te
mp
late
Page 15
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
3000 Highway 74 East bull Monroe NC 28112Tel (800)-438-1951 x4706 bull Fax (800)-338-0965
wwwnor tondoorcontrolscom
ASSA ABLOY
This PageLeft Blank
Page 16
ASSA ABLOY
BACKPLATE
REED SWITCH
CHAINOPEN CLOSE POSITIONING MAGNETS
ldquoT1rdquo POWER INPUTTERMINAL (3-POSITION)
ACCESSORYTERMINAL(4-POSITION)
PINION EXTENSION CLUTCH ASSEMBLY
INVERTER
MOTOR ASSEMBLY
POWER SWITCH
BREAKER SWITCH
1600 SERIES CLOSER BODY
CONNECTING LINKBUSHING ASSEMBLY
SHOE
SHOE ADJUSTING ROD ASSEMBLY
FOREARMSCREW
MAIN ARM
ADJUSTINGTUBE
MAIN ARM SLIDEUNIT ASSEMBLY
Included with 5710 and 5740 Included with 5730 and 5740
Component Layout
ADA ANSI UL InformationAmericans With Disabilities Act (ADA)These door operators can be installed and adjusted to conform with ADA regulations
ANSI StandardsANSI A1171 ndash These door operators permit door assemblies to conform to the requirements of this specification for buildings and facilities ndash providing accessibility and usability for physically handicapped people
bull ANSI A15619 ndash These products are designed to conform to this specification for power assist and low energy power operated doors
ndash PAS Function is designed to meet or exceed all of the requirements for the Power Assist Door
ndash POR Function is designed to meet or exceed all of the requirements for the Low Energy Power Operated Door
UL Listing Underwriters Laboratories Inc listed for use on
fire and smoke barrier door assemblies when the 120VAC (60Hz) power input is supplied through the normally closed alarm contacts of a compatible UL Listed alarm system or alarm panel
ASSA ABLOY
SLIDE TRACKASSEMBLY
SLIDER
BUFFER STOP
964rdquo HEXDRIVE SOCKET
SCREW
SLIDE ARMTUBE
SLIDE ARMROD
Page 3 Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Note Door must be visible by person operating activation switch(es)
Door OpeningAngle
Dim ldquoArdquo
Up to 110deg
111deg to 180deg
15-12 (394)
13-14 (337)
Notesbull All dimensions are given in inches (mm)bull Thickness recommended for reinforcements in hollow
metal doors and frames is charted on Page 2bull Do not scale drawingbull Right hand door shownbull This template information based upon use of 5
(127mm) maximum width butt hinges A separate template is required for other conditions
bull Maximum frame reveal is 6-78rdquo (175mm) for this application
bull Conduit hole nearest the hinge is suggested for 120 VAC power input
2rdquo (51mm) Min
Frame Face
1-18rdquo(29)
1-14(32)
1-716(37)
11(279)
22(559)
7-916(192)
13-716(341)
1-18(29)
CL Hinge
14-20 Machine Screwsor No 14 Wood Screws
(6 Places)78 (23) Dia(2 Places)
38 DiaSex Nuts(3 Places)
FrameRabbet
FrameStopSoffit
3(76)
13-1316(350)
12(13)
A
11-1116(297)
6rdquo (152mm)
MinClearance
14-316(360)
12-1516(329)
13-1316(351)
Right Hand Dooropening to 110deg shown
58(159)
Stop
1 Hinge (Pull) Side Mounting Instructions
Step 1 Determine hand of door from illustration on upper right of this page
Step 2 Using template above locate and prepare holes in the frame amp door
FrameA Prepare six (6) holes for 14-20 machine screws or
No 14 x 2-34 (70mm) wood screws Blind rivet nuts (by others) are suggested for unreinforced hollow metal frames or for aluminum frames
B Concealed Wired Units Only Two (2) 78 (22mm) diameter holes for conduit for power input and for switchsensor wires
NOTE On new construction these holes will generally be drilled by the frame supplier at their shop or at the time the frame is installed in the wall
DoorC Prepare three (3) holes for 38 diameter sex nuts Standard units
are supplied with sex nuts and screws for 1-34 (44mm) thick door Sex nuts and screws for other door thicknesses are available to order
Step 3 Remove cover from the unit and set cover amp cover screws aside
Step 4 Mount unit to door frame Select A or B below
A Concealed Wired Units Only
B Surface Wired Units Only
(Continue to next page)
Connect conduit to frame side of backplate Fasten unit to door frame (seven screws)
Fasten unit to door frame (seven screws) Mount conduit bracket (found in screw pack) to unitrsquos backplate with two screws provided Connect wiring conduit to bracket
1A Installation Sequence
LeftHandDoor
RightHandDoor
2rdquo (51mm)Min Frame
FaceFrame Reveal
Do
or
6rdquo (152mm)Min CeilingClearance
1-34rdquo (44mm) Min2-14rdquo (57mm) Max
Door Thickness
Please verify desired mounting requires Hinge (Pull) Side
application as shown on this template
Page 4
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
1A Installation Sequence ContinuedStep 5 Mount track assembly to door using 3 14-20 screws amp sex nuts
with buffer assembly toward hinge Open part of track to face top of door
Step 6 Insert slide arm rod into slide arm tube setting the distance between the pinion square and the slide stud at 13-12rdquo (343) Install 964rdquo hex drive socket head screw from screw pack (See illustration below)
Step 7 Using an adjustable wrench rotate pinion 45deg toward hinge as shown below With the arm assembly parallel to the door secure arm to pinion when square of the pinion aligns with the square in the arm Secure with countersunk washer and 14-20 Flat Head Screw (with thread lock) provided Tighten screw with 716rdquo wrench or socket
Step 9to
increase door closing power Door control is shipped set at midpoint of power setting Maximum closing power can be achieved with 8 (360deg) clockwise turns of the power adjustment screw
Step 8 Insert arm stud into slide block in track assembly Secure by pushing in on the retainer clip that extends from the slide block in the track until it is flush with the slide block (see illustration below)
Adjust closing power of unit (See Fig 1) - Using a 18rdquo allen wrench turn the power adjustment shaft clockwise
Step 10 Adjust Hydraulic valves using a 18rdquo hex wrench to obtain proper door closing speeds See following illustrations Refer to Table 1 below for recommended minimum opening closing times per ANSIBHMA A15619
Note ADA requires that from an open position of 70deg the door will take at least 3 seconds to move to a point 3rdquo (75mm) from the latched position measured at the leading edge of the door
Closing Cycle ndash Make adjustments as necessary to the Sweep Speed S valve and Latch Speed L valve See Fig 2 below for location of valves Turn valves clockwise to reduce speed counter clockwise to increase speed
Opening Cycle ndash Adjust Backcheck B valve as necessary for hydraulic resistance to door opening in the backcheck range See illustration in Fig 2 for location of valve
NOTE Too much Backcheck B valve can affect the operation of the units pump preventing units from fully opening the door This valve may require fine tuning after all other adjustments have been made
2
1Attaching Arm Stud to Slide
Retainer Clip
18HexKey
SlowerClosing
FasterClosingClosing Cycle
Closed
10deg
egnaR hctaL
egnaR peewS
18HexKey
IncreaseCushion
DecreaseCushion
Sweep Valve
Latch Valve
BackcheckValve
Figure 2
Power Adjustment
18HexKey
IncreasePower
DecreasePower Figure 1
Opening Cycle
Backcheckgninep
O
13-12(343)
Note Center threaded hole of slider arm should align with seventh hole of the slider tube Stud in slider arm should point to same side as holes in slider tube (see illustration on Page 3)
RHDoor
LHDoor
RotatePinion
Pinion Flats
1A Installation Sequence ContinuedTable 1 - Minimum Opening Closing Times for ANSIBHMA A15619Door Weight in Pounds (kg)Door Leaf
Width -Inches (mm)
Matrix values are in seconds
Backcheck - adjust the backcheck valve to have a minimum opening time to backcheck or 80 degrees (whichever comes first) based on Table 1
Closing Time - adjust Latch and Sweep valves to have a minimum closing time from 90 degrees to Latch Check or 10 degrees (whichever comes first) based on Table 1
Page 5
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Door OpeningAngle
Dim ldquoArdquo Dim ldquoBrdquo
Up to 110deg
111deg to 170deg
12 (305)
9-12 (241) 13-14 (337)
15-34 (400)
Notesbull All dimensions are given in inches (mm)bull Thickness recommended for reinforcements in
hollow metal doors and frames is charted at the left of this page
bull Do not scale drawingbull Left hand door shownbull This template information based upon use of 5
(127mm) maximum width butt hinges or 34 (19mm) offset pivots A separate template will be supplied for other conditions
bull Maximum frame reveal is 7rdquo (178mm) for this application
bull Conduit hole nearest to hinge is suggested for 120 VAC power input
1-1116(43)
1-14(32)
1116(175)
1-34(44)
12-1516(329)
7-916(192)
13-716(341)
38(10)
CL Hinge or Pivot
14-20 Machine Screwsor No 14 Wood Screws
(6 Places)
78(22)
(Conduit Holes - 2 Places)
Dia
FrameRabbet
FrameStopSoffit
A
13-1316(351)
12(13)
B
5-14rdquoMin
Clearance
11-1116(297)
38(19)
14-316(360)
13-1316(351)
Left Hand Dooropen to 110deg shown
58(159)
Stop
Sex Nuts(2 Places)
2 Stop (Push) Side Mounting Instructions
2A Installation Sequence
LeftHandDoor
RightHandDoor
1-12rdquo (38mm)Min Frame Face
Frame Reveal
Do
or
5-14rdquo (133mm)Min CeilingClearance
1-34rdquo (44mm) Min2-14rdquo (57mm) Max
Door ThicknessFor frame reveals less than 3 (76mm) the arm adjusting rod can be field cut to a length of 9-12 (241mm) measured from centerline of connecting link bushing assembly Note Door must be visible by person operating activation switch(es)
Step 1 Determine hand of door from illustration on upper right of this page
Step 2 Using template above locate and prepare holes in the frame amp door
FrameA Prepare six (6) holes for 14-20 machine screws or No 14 x 2-34
(70mm) wood screws Blind rivet nuts (by others) are suggested for unreinforced hollow metal frames or for aluminum frames
B Concealed Wired Units Only Two (2) 78 (22mm) diameter holes for conduit for power input and for switchsensor wires
NOTE On new construction these holes will generally be drilled by the frame supplier at their shop or at the time the frame is installed in the wall
DoorC Prepare two (2) holes for 38 diameter sex nuts Standard units
are supplied with sex nuts and screws for 1-34 (44mm) thick door Sex nuts and screws for other door thicknesses are available to order
Step 3 Remove cover from the unit and set cover amp cover screws aside
Step 4 Mount unit to door frame Select A or B below
A Concealed Wired Units Only
B Surface Wired Units Only
Connect conduit to frame side of backplate Fasten unit to door frame (six screws)
Fasten unit to door frame (six screws) Mount conduit bracket (found in screw pack) to unit backplate with two screws provided Connect wiring conduit to bracket
Please verify desired mounting requires Stop (Push) Side
application as shown on this template
Page 6
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
2A Installation Sequence Continued
Step 5 Install main arm onto pinion shaft of unit at a 90deg angle to the door frame Align arm mark ldquoSrdquo with the flat corner of the pinion shaft square (See Fig 3 below)
Step 6 Secure main arm to pinion with 14-20 Flange Head Screw provided Tighten screw with 716 wrench or socket
Step 9to
increase door closing power Door control is shipped set at midpoint of power setting Maximum closing power can be achieved with 8 (360deg) clockwise turns of the power adjustment screw
Step 7 Mount arm shoe to door using 2 14-20 screws amp sex nuts provided with screw pack
Step 8 PRELOAD ARM (See Fig 4 below) Remove 14-20 hex head screw on adjusting rod and insert adjusting rod into arm slide Reinstall 14-20 screw and leave loose Rotate main arm in direction away from the hinge edge until the adjusting rod and arm slide are perpendicular (at a 90deg angle) to the door frame Tighten the 14-20 hex head screw on the adjusting rod to secure arm in this new position
Adjust closing power of unit (See Fig 5) - Using a 18rdquo allen wrench turn the power adjustment shaft clockwise
Step 10 Adjust Hydraulic valves using a 18rdquo hex wrench to obtain proper door closing speeds See following illustrations Refer to Table 1 on page 5 for recommended minimum opening closing times per ANSIBHMA A15619
Note ADA requires that from an open position of 70deg the door will take at least 3 seconds to move to a point 3rdquo (75mm) from the latched position measured at the leading edge of the door
Step 11 Make wiring connections using Wiring Instructions on Page below and on Page 8
Closing Cycle ndash Make adjustments as necessary to the Sweep Speed S valve and Latch Speed L valve See Fig 6 below for location of valves Turn valves clockwise to reduce speed counter clockwise to increase speed
Opening Cycle ndash Adjust Backcheck B valve as necessary for hydraulic resistance to door opening in the backcheck range See illustration at bottom of this page for location of valve
NOTE Too much Backcheck B valve can affect the operation of the units pump preventing units from fully opening the door This valve may require fine tuning after all other adjustments have been made
R
LYS
Z
Arm Mark Pinion Flat
Figure 3
AdjustingRod
ArmSlide
DoorShoe
MainArm
Figure 4Adjusting
Rod
ArmSlide
DoorShoe
MainArm
PowerAdjustment
18HexKey
IncreasePower
DecreasePower
Figure 5
18HexKey
SlowerClosing
FasterClosing Closing Cycle
Closed
10deg
egnaR hctaL
egnaR peewS
18HexKey
IncreaseCushion
DecreaseCushion
Opening Cycle
Backcheckgninep
O
Sweep ValveLatch Valve
BackcheckValve
Figure 8
Page 7
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Low VoltageControlWiring
IncomingPower
Optional Bracket(for surface wiring)
GroundLead
PowerLeads
GroundScrew(Green)
CableClamps Conduit
by Others(from top)
ldquoT1rdquo PowerInputTerminal
24
23
22
25
HOT
COM
Breaker Switch
T1 TerminalBlock
4 Final Electrical and Mechanical SetupA Confirm all mechanical adjustments have been made
and wiring connected per Page 7 and 8B Turn on facilityrsquos main circuit breakerC Turn power to unit on at the Unit Power Switch and
turn the Breaker Switch to ldquoRESETrdquo
D Using a short jumper cable jump terminals 1 and 2 see Fig 2 below to activate unit When door reaches 20deg switch Breaker Switch to ldquoOFFrdquo position cutting power to the unit Allow door to fully close (door may be manually pulled closed)
1234
1234
Figure 2
3 Input Power ConfigurationsCONCEALED WIRING SURFACE WIRING
Ground Wire Connection ndash Ground wire must be secured to backplate under head of (green) ground screw
Terminal Description
HOT
25
23
24
22
COM Common power lead
Hot power lead
Circuit Breaker
Switch
Circuit Breaker
Common connection to Circuit Breaker Inverter
Thread conduit fitting(s) into backplate as shown A second conduit fitting is required for low voltage control wiring CHECK LOCAL CODES Pull conduit out of header and attach to conduit fittings before mounting Secure operator to door frame Attach incoming ground wire to backplate with ground screw as illustrated in ldquoSurface Wiringrdquo illustration to the Right
Thread conduit fitting(s) into backplate as shown A second conduit fitting is required for low voltage control wiring CHECK LOCAL CODES Pull conduit out of header and attach to conduit fittings before mounting Secure operator to door frame Attach incoming ground wire to backplate with ground screw as illustrated below
Breaker Switch
Unit Power Switch
Page 8
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
4 Final Electrical and Mechanical Setup ContinuedE Adjust Closing Position Magnet (See Fig 3) - With
door in the closed position use finger to slide Closed Position Magnet so it aligns directly with the Reed Switch
F Adjust Open Position Magnet - Use fingers to slide
F cont Open Position Magnet 180deg from Open Position Magnet
G Flip Breaker Switch to ldquoRESETrdquo to turn power on Jump terminals 1 and 2 (as shown in Fig 2) to activate door Note open position of the door Allow door to close
H Use finger to readjust the Open Position Magnet to desired door open position
I Repeat Step G to verify door open position J Make all connections necessary for any accessories to
the 4-position Accessory Terminal (see Pages 10-11)K Make necessary adjustments to inverter (see Page 9)
Replace cover and cover screws
Reed Switch
Closed Position Magnet
Open PositionMagnet
Position Ring
Figure 3
Inverter Adjustmentsmiddot Based on function
adjustment desired use table above to determine which POT is to be adjusted
POT FUNCTIONDESCRIPTION
OBSTR SENS Obstruction Detection on Open CW - IncreaseCCW - Decrease
MDLY Motor Delay on Opening CW - IncreaseCCW - Decrease
P1 Closing Speed CW - IncreaseCCW - Decrease
HO TM Hold Open Time (5 - 30 Seconds) CW - IncreaseCCW - Decrease
P2 Opening Speed CW - IncreaseCCW - Decrease
HO TQMotor Torque at Hold Open Position
CW - IncreaseCCW - Decrease
ON
12
WARNING
120 HIGH VOLT POTENTIAL PRESENT MAKE SURE POWER IS TURNED OFF DURING
INSTALLATION PROCEDURE
Dip Switch Settings
1 Door Mounting -
2 Push Recognition -
ON - pullOFF - pushON - activeOFF - inactive
WARNINGElectric
Shock Risk
(Adjustments made in the shaded area should be performed by
Authorized Factory Personnel)
L2115Y
L1 115230VAC IN
MOTOR OUT
L2230Y
U
V
W
STATUS LEDS
HO TQHO TM
OBSTRSENS
P1
MDLY P2
16
COM
SNS
COM
PB
K1
K2
11
JMP503
NC
NO
TB501
PU
LL P
US
HSW501
ON
12
Inverter Details
Page 9
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Standard Function with Switches
1
2
3
4
1
2
3
4
Notes1Power input to Door
Operator Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
Wall Switch CardReader Key Switchetc
1
2
3
4
1
2
3
4Door 1 Door 2
Operationbull bull Activating either switch will
open both doors Door will close after hold open time delay has elapsed
Doors are normally closed
Wall Switch CardReader Key Switchetc
Normally Open Momentary dry contacts
Normally Open Momentary dry contacts
Radio Frequency Function Option
1 2 3 4
1 2 3 4
Optional Door 2
1 2 3 4
1 2 3 4
Door 1
Notes1Power input to Door Operator
Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
2 Radio Frequency Feature can be purchased as a separate kit
Operationbull
closedbull Activating wireless
switch or hand held wireless transmitter will open the door
bull Door will close after hold open delay elapses
Door is normally
120VAC
GroundC
OM
HO
TL N(AC) -V +V ADJ
+
11A 24V Power Supply12-24 VA
CD
CC
OM
NO
NC
Troubleshooting
Jump activation input
Change the setting of the ONOFF switch
Flip Door Mounting Dip Switch to other direction
Remove object
Re-time and re-install arm
Increase spring tension per preceding instructions
Remove object
Fault Possible reasons why RemediesExplanations
The door does not open- The motor does not start
Control switch is set to OFF position
Electrical power is missing the electrical Check power switch
Activation unit does not function- The motor starts Motor is driving in wrong direction
Something jammed beneath the door
Arm has come loose
The door does not close Spring tension too lowArm has come loose Re-time and re-install arm
Something jammed beneath the door
Circuit breaker is set to OFF position Reset circuit breaker to the ON position
Page 10
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Fail Secure Fail Safe Electric Strike Wiring
120VACSupplied byOthers- +
DC or ACOutput
AC
or
DC
Ele
ctric
Str
ike+
-
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating for strike interface 30VDC 1A or 125VAC 5A
Operationbull bull Activating switch will unlock the electric strike
and the door will automatically open Door will close after hold open time delay has elapsed
bull For Fail Secure Strike - The door will remain locked during power failure
bull For Fail Safe Strike - The door will remain unlocked during power failure
Door is normally closed and latched
1
2
3
4
1
2
3
4
JMP503
NC
NO
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
Fail Safe Electromagnetic Lock 24VDC Wiring
1
2
3
4
1
2
3
4
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
+-24VDC Electromagnetic Lock(Fail Safe)
Operationbull bull Activating switch will cut power to mag lock and the door will automatically
open Door will close after hold open time delay has elapsedbull The door will unlock during power failure
Door is normally closed and latched
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating 30VDC 1A or 125VAC 5A
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
JMP503
NC
NO
120VAC
GroundC
OM
HO
T
L N(AC) -V +V ADJ+
Optional 11A 24V Power Supply
Page 11
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Page 12
Troubleshooting
Red LEDBlue LED
Antenna Wire
Learnwo DelayButton
DelayPotentiometer(Time Adjustment)
Learn wDelay Button
DIP Switch
TerminalStrip
Problem The LED on my receiver is just flickering and Irsquom unable to program andor it wonrsquot workSolution You have a push plate stuck or faulty transmitter Disconnect each push plate until the LED goes out If LED
does not go out remove each transmitter battery until it does Replace the appropriate transmitterProblem Receiver intermittently doesnrsquot receive the transmitter(s) signal
Solution You may extend the receiver antenna wire only in multiples of 6-34rdquo (171) ie 675 x 4 = 27rdquo (686) of extended antenna wire
Removing Transmitter Code(s)
Single Transmitter CodeŸ Press both Delay and No Delay Buttons simultaneously until Red LED flashes once (approximately 1 second)Ÿ Press transmitter button twice within 10 seconds and the transmitter code will be deleted
All Transmitter CodesŸ Press and hold both Delay and No Delay Buttons simultaneously until Blue LED illuminates then release (approximately 10
seconds)
Push Plate Configuration
1 Before beginning it is easiest to have already prepared the installation of the push plate2 Connect the wires from the transmitter to the NO and COM contacts of the push platersquos switch3 Follow Steps 1 - 4 (Hand-Held Configuration) depress the push plate to activate the transmitter4 Attach the transmitter to the inside of the electrical box and complete the installation
Hand-Held Configuration
1 Set dip switches to the receiver to the desired activation cycle (dip switch 1 - Toggle or Pulse and dip switch 2 - 05s or 10s hold
2 Press either Learn w Delay Button or Learn wo Delay Button on the receiver depending on the activation requirements (if delay learn is selected adjust potentiometer to counterclockwise limit 0 second delay) Red LED on receiver will flash After learn cycle is complete adjust potentiometer to desired delay time (0 - 30 sec)
3 Depress transmitter button repeatedly until Blue LED on the receiver illuminates (indicating reception of signal from transmitter) NOTE Repeat Steps 2 - 3 to program additional transmitters
4 To test the system depress transmitter button (Red LED on Transmitter will illuminate) and observe that the Blue LED illuminates on the receiver This indicates that the relay has been activated
433MHz Receiver Userrsquos Guide
2OFFON
Description05s Hold Time10s Hold Time
FunctionRelay will remain active 05 sec after loss of activationRelay will remain active 10 sec after loss of activation
1OFF
ON
DescriptionPulse Relay
Toggle Relay
FunctionPress the transmitter once and the relay will be active momentarilyPress the transmitter once and the relay output is active indefinitely press it again and the relay will de-energize indefinitely
ON
1 2PU
L T
OG
05s
1
0s ON
1 2PU
L T
OG
05s
1
0sIn Toggle Setting (1-ON) the Hold Time is inactive Either setting for 2 dip switch will
have the same result
ON
1 2PU
L T
OG
05s
1
0s
05 second Pulse Setting
ON
1 2PU
L T
OG
05s
1
0s
10 second Pulse Setting
ŸAlways stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door
ŸEnsure compliance with all applicable safety standards upon completion of installation
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
This PageLeft Blank
Page 13
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Hinge (Pull) SideŸ Do not scale drawingŸ Right hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
No
te D
oo
r m
ust
be
visi
ble
by
per
son
o
per
atin
g a
ctiv
atio
n s
wit
ch(e
s)
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Up
to 1
10deg
111deg
to 1
80deg
15-1
2 (
394)
13-1
4 (
337)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull T
hick
ness
rec
omm
ende
d fo
r re
info
rcem
ents
in h
ollo
w
met
al d
oors
and
fram
es is
cha
rted
on
Pag
e 2
bull D
o no
t sca
le d
raw
ing
bull R
ight
han
d do
or s
how
nbull
Thi
s te
mpl
ate
info
rmat
ion
base
d up
on u
se o
f 5
(127
mm
) m
axim
um w
idth
but
t hin
ges
A s
epar
ate
tem
plat
e is
req
uire
d fo
r ot
her
cond
ition
sbull
Max
imum
fram
e re
veal
is 6
-78
rdquo (17
5mm
) fo
r th
is
appl
icat
ion
bull C
ondu
it ho
le n
eare
st th
e hi
nge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
2rdquo (
51m
m)
Min
F
ram
e Fa
ce
1-1
8rdquo(2
9)
1-1
4(3
2)1-
716
(37)
11(2
79)
22(5
59)
7-9
16(1
92)
13-7
16
(341
)
1-1
8(2
9)
C LH
inge
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)7
8 (2
3) D
ia
(2 P
lace
s)
38
Dia
S
ex N
uts
(3 P
lace
s)
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
3(7
6)
13-1
316
(350
)
12
(13)
A
11-1
116
(297
)
6rdquo
(152
mm
)M
in
Cle
aran
ce
14-3
16
(360
)
12-1
516
(329
)13
-13
16(3
51)
Rig
ht
Han
d D
oo
ro
pen
ing
to
110
deg sh
ow
n
58
(15
9)S
top
Left
Han
dD
oor
Rig
htH
and
Doo
r
2rdquo (
51m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
6rdquo (
152m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
ax
Do
or T
hic
knes
s
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Hin
ge
(Pu
ll) S
ide
app
licat
ion
as
sho
wn
on
th
is
tem
pla
te
Page 14
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Stop (Push) SideŸ Do not scale drawingŸ Left hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Dim
ldquoB
rdquo
Up
to 1
10deg
111deg
to 1
70deg
12 (
305)
9-1
2 (2
41)
13-1
4 (
337)
15-3
4 (
400)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull Thi
ckne
ss r
ecom
men
ded
for
rein
forc
emen
ts in
ho
llow
met
al d
oors
and
fram
es is
cha
rted
at t
he
left
of th
is p
age
bull D
o no
t sca
le d
raw
ing
bull Le
ft ha
nd d
oor
show
nbull T
his
tem
plat
e in
form
atio
n ba
sed
upon
use
of 5
(1
27m
m)
max
imum
wid
th b
utt h
inge
s or
34
(1
9mm
) of
fset
piv
ots
A s
epar
ate
tem
plat
e w
ill
be s
uppl
ied
for
othe
r co
nditi
ons
bull M
axim
um fr
ame
reve
al is
7rdquo (
178m
m)
for
this
ap
plic
atio
nbull
Con
duit
hole
nea
rest
to h
inge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
1-11
16
(43)
1-1
4(3
2)11
16
(17
5)
1-3
4(4
4)
12-1
516
(329
)
7-9
16(1
92)
13-7
16
(341
)
38
(10)
C LH
inge
or
Piv
ot
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)
78
(22)
(Con
duit
Hol
es -
2
Pla
ces)
Dia
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
A13-1
316
(351
)
12
(13)
B
5-1
4rdquoM
in
Cle
aran
ce
11-1
116
(297
)
38
(19)
14-3
16
(360
)13
-13
16(3
51)
Lef
t H
and
Do
or
op
en t
o 1
10deg
sho
wn
58
(15
9)S
top
Sex
Nu
ts(2
Pla
ces)
Left
Han
dD
oor
Rig
htH
and
Doo
r
1-1
2rdquo (
38m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
5-1
4rdquo (
133m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
axD
oo
r Th
ickn
ess
No
te D
oo
r m
ust
be
visi
ble
by
per
son
op
erat
ing
act
ivat
ion
sw
itch
(es)
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Sto
p (
Pu
sh)
Sid
e ap
plic
atio
n a
s sh
ow
n o
n t
his
te
mp
late
Page 15
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
3000 Highway 74 East bull Monroe NC 28112Tel (800)-438-1951 x4706 bull Fax (800)-338-0965
wwwnor tondoorcontrolscom
ASSA ABLOY
This PageLeft Blank
Page 16
ASSA ABLOY
Note Door must be visible by person operating activation switch(es)
Door OpeningAngle
Dim ldquoArdquo
Up to 110deg
111deg to 180deg
15-12 (394)
13-14 (337)
Notesbull All dimensions are given in inches (mm)bull Thickness recommended for reinforcements in hollow
metal doors and frames is charted on Page 2bull Do not scale drawingbull Right hand door shownbull This template information based upon use of 5
(127mm) maximum width butt hinges A separate template is required for other conditions
bull Maximum frame reveal is 6-78rdquo (175mm) for this application
bull Conduit hole nearest the hinge is suggested for 120 VAC power input
2rdquo (51mm) Min
Frame Face
1-18rdquo(29)
1-14(32)
1-716(37)
11(279)
22(559)
7-916(192)
13-716(341)
1-18(29)
CL Hinge
14-20 Machine Screwsor No 14 Wood Screws
(6 Places)78 (23) Dia(2 Places)
38 DiaSex Nuts(3 Places)
FrameRabbet
FrameStopSoffit
3(76)
13-1316(350)
12(13)
A
11-1116(297)
6rdquo (152mm)
MinClearance
14-316(360)
12-1516(329)
13-1316(351)
Right Hand Dooropening to 110deg shown
58(159)
Stop
1 Hinge (Pull) Side Mounting Instructions
Step 1 Determine hand of door from illustration on upper right of this page
Step 2 Using template above locate and prepare holes in the frame amp door
FrameA Prepare six (6) holes for 14-20 machine screws or
No 14 x 2-34 (70mm) wood screws Blind rivet nuts (by others) are suggested for unreinforced hollow metal frames or for aluminum frames
B Concealed Wired Units Only Two (2) 78 (22mm) diameter holes for conduit for power input and for switchsensor wires
NOTE On new construction these holes will generally be drilled by the frame supplier at their shop or at the time the frame is installed in the wall
DoorC Prepare three (3) holes for 38 diameter sex nuts Standard units
are supplied with sex nuts and screws for 1-34 (44mm) thick door Sex nuts and screws for other door thicknesses are available to order
Step 3 Remove cover from the unit and set cover amp cover screws aside
Step 4 Mount unit to door frame Select A or B below
A Concealed Wired Units Only
B Surface Wired Units Only
(Continue to next page)
Connect conduit to frame side of backplate Fasten unit to door frame (seven screws)
Fasten unit to door frame (seven screws) Mount conduit bracket (found in screw pack) to unitrsquos backplate with two screws provided Connect wiring conduit to bracket
1A Installation Sequence
LeftHandDoor
RightHandDoor
2rdquo (51mm)Min Frame
FaceFrame Reveal
Do
or
6rdquo (152mm)Min CeilingClearance
1-34rdquo (44mm) Min2-14rdquo (57mm) Max
Door Thickness
Please verify desired mounting requires Hinge (Pull) Side
application as shown on this template
Page 4
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
1A Installation Sequence ContinuedStep 5 Mount track assembly to door using 3 14-20 screws amp sex nuts
with buffer assembly toward hinge Open part of track to face top of door
Step 6 Insert slide arm rod into slide arm tube setting the distance between the pinion square and the slide stud at 13-12rdquo (343) Install 964rdquo hex drive socket head screw from screw pack (See illustration below)
Step 7 Using an adjustable wrench rotate pinion 45deg toward hinge as shown below With the arm assembly parallel to the door secure arm to pinion when square of the pinion aligns with the square in the arm Secure with countersunk washer and 14-20 Flat Head Screw (with thread lock) provided Tighten screw with 716rdquo wrench or socket
Step 9to
increase door closing power Door control is shipped set at midpoint of power setting Maximum closing power can be achieved with 8 (360deg) clockwise turns of the power adjustment screw
Step 8 Insert arm stud into slide block in track assembly Secure by pushing in on the retainer clip that extends from the slide block in the track until it is flush with the slide block (see illustration below)
Adjust closing power of unit (See Fig 1) - Using a 18rdquo allen wrench turn the power adjustment shaft clockwise
Step 10 Adjust Hydraulic valves using a 18rdquo hex wrench to obtain proper door closing speeds See following illustrations Refer to Table 1 below for recommended minimum opening closing times per ANSIBHMA A15619
Note ADA requires that from an open position of 70deg the door will take at least 3 seconds to move to a point 3rdquo (75mm) from the latched position measured at the leading edge of the door
Closing Cycle ndash Make adjustments as necessary to the Sweep Speed S valve and Latch Speed L valve See Fig 2 below for location of valves Turn valves clockwise to reduce speed counter clockwise to increase speed
Opening Cycle ndash Adjust Backcheck B valve as necessary for hydraulic resistance to door opening in the backcheck range See illustration in Fig 2 for location of valve
NOTE Too much Backcheck B valve can affect the operation of the units pump preventing units from fully opening the door This valve may require fine tuning after all other adjustments have been made
2
1Attaching Arm Stud to Slide
Retainer Clip
18HexKey
SlowerClosing
FasterClosingClosing Cycle
Closed
10deg
egnaR hctaL
egnaR peewS
18HexKey
IncreaseCushion
DecreaseCushion
Sweep Valve
Latch Valve
BackcheckValve
Figure 2
Power Adjustment
18HexKey
IncreasePower
DecreasePower Figure 1
Opening Cycle
Backcheckgninep
O
13-12(343)
Note Center threaded hole of slider arm should align with seventh hole of the slider tube Stud in slider arm should point to same side as holes in slider tube (see illustration on Page 3)
RHDoor
LHDoor
RotatePinion
Pinion Flats
1A Installation Sequence ContinuedTable 1 - Minimum Opening Closing Times for ANSIBHMA A15619Door Weight in Pounds (kg)Door Leaf
Width -Inches (mm)
Matrix values are in seconds
Backcheck - adjust the backcheck valve to have a minimum opening time to backcheck or 80 degrees (whichever comes first) based on Table 1
Closing Time - adjust Latch and Sweep valves to have a minimum closing time from 90 degrees to Latch Check or 10 degrees (whichever comes first) based on Table 1
Page 5
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Door OpeningAngle
Dim ldquoArdquo Dim ldquoBrdquo
Up to 110deg
111deg to 170deg
12 (305)
9-12 (241) 13-14 (337)
15-34 (400)
Notesbull All dimensions are given in inches (mm)bull Thickness recommended for reinforcements in
hollow metal doors and frames is charted at the left of this page
bull Do not scale drawingbull Left hand door shownbull This template information based upon use of 5
(127mm) maximum width butt hinges or 34 (19mm) offset pivots A separate template will be supplied for other conditions
bull Maximum frame reveal is 7rdquo (178mm) for this application
bull Conduit hole nearest to hinge is suggested for 120 VAC power input
1-1116(43)
1-14(32)
1116(175)
1-34(44)
12-1516(329)
7-916(192)
13-716(341)
38(10)
CL Hinge or Pivot
14-20 Machine Screwsor No 14 Wood Screws
(6 Places)
78(22)
(Conduit Holes - 2 Places)
Dia
FrameRabbet
FrameStopSoffit
A
13-1316(351)
12(13)
B
5-14rdquoMin
Clearance
11-1116(297)
38(19)
14-316(360)
13-1316(351)
Left Hand Dooropen to 110deg shown
58(159)
Stop
Sex Nuts(2 Places)
2 Stop (Push) Side Mounting Instructions
2A Installation Sequence
LeftHandDoor
RightHandDoor
1-12rdquo (38mm)Min Frame Face
Frame Reveal
Do
or
5-14rdquo (133mm)Min CeilingClearance
1-34rdquo (44mm) Min2-14rdquo (57mm) Max
Door ThicknessFor frame reveals less than 3 (76mm) the arm adjusting rod can be field cut to a length of 9-12 (241mm) measured from centerline of connecting link bushing assembly Note Door must be visible by person operating activation switch(es)
Step 1 Determine hand of door from illustration on upper right of this page
Step 2 Using template above locate and prepare holes in the frame amp door
FrameA Prepare six (6) holes for 14-20 machine screws or No 14 x 2-34
(70mm) wood screws Blind rivet nuts (by others) are suggested for unreinforced hollow metal frames or for aluminum frames
B Concealed Wired Units Only Two (2) 78 (22mm) diameter holes for conduit for power input and for switchsensor wires
NOTE On new construction these holes will generally be drilled by the frame supplier at their shop or at the time the frame is installed in the wall
DoorC Prepare two (2) holes for 38 diameter sex nuts Standard units
are supplied with sex nuts and screws for 1-34 (44mm) thick door Sex nuts and screws for other door thicknesses are available to order
Step 3 Remove cover from the unit and set cover amp cover screws aside
Step 4 Mount unit to door frame Select A or B below
A Concealed Wired Units Only
B Surface Wired Units Only
Connect conduit to frame side of backplate Fasten unit to door frame (six screws)
Fasten unit to door frame (six screws) Mount conduit bracket (found in screw pack) to unit backplate with two screws provided Connect wiring conduit to bracket
Please verify desired mounting requires Stop (Push) Side
application as shown on this template
Page 6
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
2A Installation Sequence Continued
Step 5 Install main arm onto pinion shaft of unit at a 90deg angle to the door frame Align arm mark ldquoSrdquo with the flat corner of the pinion shaft square (See Fig 3 below)
Step 6 Secure main arm to pinion with 14-20 Flange Head Screw provided Tighten screw with 716 wrench or socket
Step 9to
increase door closing power Door control is shipped set at midpoint of power setting Maximum closing power can be achieved with 8 (360deg) clockwise turns of the power adjustment screw
Step 7 Mount arm shoe to door using 2 14-20 screws amp sex nuts provided with screw pack
Step 8 PRELOAD ARM (See Fig 4 below) Remove 14-20 hex head screw on adjusting rod and insert adjusting rod into arm slide Reinstall 14-20 screw and leave loose Rotate main arm in direction away from the hinge edge until the adjusting rod and arm slide are perpendicular (at a 90deg angle) to the door frame Tighten the 14-20 hex head screw on the adjusting rod to secure arm in this new position
Adjust closing power of unit (See Fig 5) - Using a 18rdquo allen wrench turn the power adjustment shaft clockwise
Step 10 Adjust Hydraulic valves using a 18rdquo hex wrench to obtain proper door closing speeds See following illustrations Refer to Table 1 on page 5 for recommended minimum opening closing times per ANSIBHMA A15619
Note ADA requires that from an open position of 70deg the door will take at least 3 seconds to move to a point 3rdquo (75mm) from the latched position measured at the leading edge of the door
Step 11 Make wiring connections using Wiring Instructions on Page below and on Page 8
Closing Cycle ndash Make adjustments as necessary to the Sweep Speed S valve and Latch Speed L valve See Fig 6 below for location of valves Turn valves clockwise to reduce speed counter clockwise to increase speed
Opening Cycle ndash Adjust Backcheck B valve as necessary for hydraulic resistance to door opening in the backcheck range See illustration at bottom of this page for location of valve
NOTE Too much Backcheck B valve can affect the operation of the units pump preventing units from fully opening the door This valve may require fine tuning after all other adjustments have been made
R
LYS
Z
Arm Mark Pinion Flat
Figure 3
AdjustingRod
ArmSlide
DoorShoe
MainArm
Figure 4Adjusting
Rod
ArmSlide
DoorShoe
MainArm
PowerAdjustment
18HexKey
IncreasePower
DecreasePower
Figure 5
18HexKey
SlowerClosing
FasterClosing Closing Cycle
Closed
10deg
egnaR hctaL
egnaR peewS
18HexKey
IncreaseCushion
DecreaseCushion
Opening Cycle
Backcheckgninep
O
Sweep ValveLatch Valve
BackcheckValve
Figure 8
Page 7
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Low VoltageControlWiring
IncomingPower
Optional Bracket(for surface wiring)
GroundLead
PowerLeads
GroundScrew(Green)
CableClamps Conduit
by Others(from top)
ldquoT1rdquo PowerInputTerminal
24
23
22
25
HOT
COM
Breaker Switch
T1 TerminalBlock
4 Final Electrical and Mechanical SetupA Confirm all mechanical adjustments have been made
and wiring connected per Page 7 and 8B Turn on facilityrsquos main circuit breakerC Turn power to unit on at the Unit Power Switch and
turn the Breaker Switch to ldquoRESETrdquo
D Using a short jumper cable jump terminals 1 and 2 see Fig 2 below to activate unit When door reaches 20deg switch Breaker Switch to ldquoOFFrdquo position cutting power to the unit Allow door to fully close (door may be manually pulled closed)
1234
1234
Figure 2
3 Input Power ConfigurationsCONCEALED WIRING SURFACE WIRING
Ground Wire Connection ndash Ground wire must be secured to backplate under head of (green) ground screw
Terminal Description
HOT
25
23
24
22
COM Common power lead
Hot power lead
Circuit Breaker
Switch
Circuit Breaker
Common connection to Circuit Breaker Inverter
Thread conduit fitting(s) into backplate as shown A second conduit fitting is required for low voltage control wiring CHECK LOCAL CODES Pull conduit out of header and attach to conduit fittings before mounting Secure operator to door frame Attach incoming ground wire to backplate with ground screw as illustrated in ldquoSurface Wiringrdquo illustration to the Right
Thread conduit fitting(s) into backplate as shown A second conduit fitting is required for low voltage control wiring CHECK LOCAL CODES Pull conduit out of header and attach to conduit fittings before mounting Secure operator to door frame Attach incoming ground wire to backplate with ground screw as illustrated below
Breaker Switch
Unit Power Switch
Page 8
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
4 Final Electrical and Mechanical Setup ContinuedE Adjust Closing Position Magnet (See Fig 3) - With
door in the closed position use finger to slide Closed Position Magnet so it aligns directly with the Reed Switch
F Adjust Open Position Magnet - Use fingers to slide
F cont Open Position Magnet 180deg from Open Position Magnet
G Flip Breaker Switch to ldquoRESETrdquo to turn power on Jump terminals 1 and 2 (as shown in Fig 2) to activate door Note open position of the door Allow door to close
H Use finger to readjust the Open Position Magnet to desired door open position
I Repeat Step G to verify door open position J Make all connections necessary for any accessories to
the 4-position Accessory Terminal (see Pages 10-11)K Make necessary adjustments to inverter (see Page 9)
Replace cover and cover screws
Reed Switch
Closed Position Magnet
Open PositionMagnet
Position Ring
Figure 3
Inverter Adjustmentsmiddot Based on function
adjustment desired use table above to determine which POT is to be adjusted
POT FUNCTIONDESCRIPTION
OBSTR SENS Obstruction Detection on Open CW - IncreaseCCW - Decrease
MDLY Motor Delay on Opening CW - IncreaseCCW - Decrease
P1 Closing Speed CW - IncreaseCCW - Decrease
HO TM Hold Open Time (5 - 30 Seconds) CW - IncreaseCCW - Decrease
P2 Opening Speed CW - IncreaseCCW - Decrease
HO TQMotor Torque at Hold Open Position
CW - IncreaseCCW - Decrease
ON
12
WARNING
120 HIGH VOLT POTENTIAL PRESENT MAKE SURE POWER IS TURNED OFF DURING
INSTALLATION PROCEDURE
Dip Switch Settings
1 Door Mounting -
2 Push Recognition -
ON - pullOFF - pushON - activeOFF - inactive
WARNINGElectric
Shock Risk
(Adjustments made in the shaded area should be performed by
Authorized Factory Personnel)
L2115Y
L1 115230VAC IN
MOTOR OUT
L2230Y
U
V
W
STATUS LEDS
HO TQHO TM
OBSTRSENS
P1
MDLY P2
16
COM
SNS
COM
PB
K1
K2
11
JMP503
NC
NO
TB501
PU
LL P
US
HSW501
ON
12
Inverter Details
Page 9
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Standard Function with Switches
1
2
3
4
1
2
3
4
Notes1Power input to Door
Operator Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
Wall Switch CardReader Key Switchetc
1
2
3
4
1
2
3
4Door 1 Door 2
Operationbull bull Activating either switch will
open both doors Door will close after hold open time delay has elapsed
Doors are normally closed
Wall Switch CardReader Key Switchetc
Normally Open Momentary dry contacts
Normally Open Momentary dry contacts
Radio Frequency Function Option
1 2 3 4
1 2 3 4
Optional Door 2
1 2 3 4
1 2 3 4
Door 1
Notes1Power input to Door Operator
Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
2 Radio Frequency Feature can be purchased as a separate kit
Operationbull
closedbull Activating wireless
switch or hand held wireless transmitter will open the door
bull Door will close after hold open delay elapses
Door is normally
120VAC
GroundC
OM
HO
TL N(AC) -V +V ADJ
+
11A 24V Power Supply12-24 VA
CD
CC
OM
NO
NC
Troubleshooting
Jump activation input
Change the setting of the ONOFF switch
Flip Door Mounting Dip Switch to other direction
Remove object
Re-time and re-install arm
Increase spring tension per preceding instructions
Remove object
Fault Possible reasons why RemediesExplanations
The door does not open- The motor does not start
Control switch is set to OFF position
Electrical power is missing the electrical Check power switch
Activation unit does not function- The motor starts Motor is driving in wrong direction
Something jammed beneath the door
Arm has come loose
The door does not close Spring tension too lowArm has come loose Re-time and re-install arm
Something jammed beneath the door
Circuit breaker is set to OFF position Reset circuit breaker to the ON position
Page 10
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Fail Secure Fail Safe Electric Strike Wiring
120VACSupplied byOthers- +
DC or ACOutput
AC
or
DC
Ele
ctric
Str
ike+
-
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating for strike interface 30VDC 1A or 125VAC 5A
Operationbull bull Activating switch will unlock the electric strike
and the door will automatically open Door will close after hold open time delay has elapsed
bull For Fail Secure Strike - The door will remain locked during power failure
bull For Fail Safe Strike - The door will remain unlocked during power failure
Door is normally closed and latched
1
2
3
4
1
2
3
4
JMP503
NC
NO
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
Fail Safe Electromagnetic Lock 24VDC Wiring
1
2
3
4
1
2
3
4
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
+-24VDC Electromagnetic Lock(Fail Safe)
Operationbull bull Activating switch will cut power to mag lock and the door will automatically
open Door will close after hold open time delay has elapsedbull The door will unlock during power failure
Door is normally closed and latched
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating 30VDC 1A or 125VAC 5A
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
JMP503
NC
NO
120VAC
GroundC
OM
HO
T
L N(AC) -V +V ADJ+
Optional 11A 24V Power Supply
Page 11
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Page 12
Troubleshooting
Red LEDBlue LED
Antenna Wire
Learnwo DelayButton
DelayPotentiometer(Time Adjustment)
Learn wDelay Button
DIP Switch
TerminalStrip
Problem The LED on my receiver is just flickering and Irsquom unable to program andor it wonrsquot workSolution You have a push plate stuck or faulty transmitter Disconnect each push plate until the LED goes out If LED
does not go out remove each transmitter battery until it does Replace the appropriate transmitterProblem Receiver intermittently doesnrsquot receive the transmitter(s) signal
Solution You may extend the receiver antenna wire only in multiples of 6-34rdquo (171) ie 675 x 4 = 27rdquo (686) of extended antenna wire
Removing Transmitter Code(s)
Single Transmitter CodeŸ Press both Delay and No Delay Buttons simultaneously until Red LED flashes once (approximately 1 second)Ÿ Press transmitter button twice within 10 seconds and the transmitter code will be deleted
All Transmitter CodesŸ Press and hold both Delay and No Delay Buttons simultaneously until Blue LED illuminates then release (approximately 10
seconds)
Push Plate Configuration
1 Before beginning it is easiest to have already prepared the installation of the push plate2 Connect the wires from the transmitter to the NO and COM contacts of the push platersquos switch3 Follow Steps 1 - 4 (Hand-Held Configuration) depress the push plate to activate the transmitter4 Attach the transmitter to the inside of the electrical box and complete the installation
Hand-Held Configuration
1 Set dip switches to the receiver to the desired activation cycle (dip switch 1 - Toggle or Pulse and dip switch 2 - 05s or 10s hold
2 Press either Learn w Delay Button or Learn wo Delay Button on the receiver depending on the activation requirements (if delay learn is selected adjust potentiometer to counterclockwise limit 0 second delay) Red LED on receiver will flash After learn cycle is complete adjust potentiometer to desired delay time (0 - 30 sec)
3 Depress transmitter button repeatedly until Blue LED on the receiver illuminates (indicating reception of signal from transmitter) NOTE Repeat Steps 2 - 3 to program additional transmitters
4 To test the system depress transmitter button (Red LED on Transmitter will illuminate) and observe that the Blue LED illuminates on the receiver This indicates that the relay has been activated
433MHz Receiver Userrsquos Guide
2OFFON
Description05s Hold Time10s Hold Time
FunctionRelay will remain active 05 sec after loss of activationRelay will remain active 10 sec after loss of activation
1OFF
ON
DescriptionPulse Relay
Toggle Relay
FunctionPress the transmitter once and the relay will be active momentarilyPress the transmitter once and the relay output is active indefinitely press it again and the relay will de-energize indefinitely
ON
1 2PU
L T
OG
05s
1
0s ON
1 2PU
L T
OG
05s
1
0sIn Toggle Setting (1-ON) the Hold Time is inactive Either setting for 2 dip switch will
have the same result
ON
1 2PU
L T
OG
05s
1
0s
05 second Pulse Setting
ON
1 2PU
L T
OG
05s
1
0s
10 second Pulse Setting
ŸAlways stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door
ŸEnsure compliance with all applicable safety standards upon completion of installation
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
This PageLeft Blank
Page 13
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Hinge (Pull) SideŸ Do not scale drawingŸ Right hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
No
te D
oo
r m
ust
be
visi
ble
by
per
son
o
per
atin
g a
ctiv
atio
n s
wit
ch(e
s)
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Up
to 1
10deg
111deg
to 1
80deg
15-1
2 (
394)
13-1
4 (
337)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull T
hick
ness
rec
omm
ende
d fo
r re
info
rcem
ents
in h
ollo
w
met
al d
oors
and
fram
es is
cha
rted
on
Pag
e 2
bull D
o no
t sca
le d
raw
ing
bull R
ight
han
d do
or s
how
nbull
Thi
s te
mpl
ate
info
rmat
ion
base
d up
on u
se o
f 5
(127
mm
) m
axim
um w
idth
but
t hin
ges
A s
epar
ate
tem
plat
e is
req
uire
d fo
r ot
her
cond
ition
sbull
Max
imum
fram
e re
veal
is 6
-78
rdquo (17
5mm
) fo
r th
is
appl
icat
ion
bull C
ondu
it ho
le n
eare
st th
e hi
nge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
2rdquo (
51m
m)
Min
F
ram
e Fa
ce
1-1
8rdquo(2
9)
1-1
4(3
2)1-
716
(37)
11(2
79)
22(5
59)
7-9
16(1
92)
13-7
16
(341
)
1-1
8(2
9)
C LH
inge
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)7
8 (2
3) D
ia
(2 P
lace
s)
38
Dia
S
ex N
uts
(3 P
lace
s)
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
3(7
6)
13-1
316
(350
)
12
(13)
A
11-1
116
(297
)
6rdquo
(152
mm
)M
in
Cle
aran
ce
14-3
16
(360
)
12-1
516
(329
)13
-13
16(3
51)
Rig
ht
Han
d D
oo
ro
pen
ing
to
110
deg sh
ow
n
58
(15
9)S
top
Left
Han
dD
oor
Rig
htH
and
Doo
r
2rdquo (
51m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
6rdquo (
152m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
ax
Do
or T
hic
knes
s
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Hin
ge
(Pu
ll) S
ide
app
licat
ion
as
sho
wn
on
th
is
tem
pla
te
Page 14
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Stop (Push) SideŸ Do not scale drawingŸ Left hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Dim
ldquoB
rdquo
Up
to 1
10deg
111deg
to 1
70deg
12 (
305)
9-1
2 (2
41)
13-1
4 (
337)
15-3
4 (
400)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull Thi
ckne
ss r
ecom
men
ded
for
rein
forc
emen
ts in
ho
llow
met
al d
oors
and
fram
es is
cha
rted
at t
he
left
of th
is p
age
bull D
o no
t sca
le d
raw
ing
bull Le
ft ha
nd d
oor
show
nbull T
his
tem
plat
e in
form
atio
n ba
sed
upon
use
of 5
(1
27m
m)
max
imum
wid
th b
utt h
inge
s or
34
(1
9mm
) of
fset
piv
ots
A s
epar
ate
tem
plat
e w
ill
be s
uppl
ied
for
othe
r co
nditi
ons
bull M
axim
um fr
ame
reve
al is
7rdquo (
178m
m)
for
this
ap
plic
atio
nbull
Con
duit
hole
nea
rest
to h
inge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
1-11
16
(43)
1-1
4(3
2)11
16
(17
5)
1-3
4(4
4)
12-1
516
(329
)
7-9
16(1
92)
13-7
16
(341
)
38
(10)
C LH
inge
or
Piv
ot
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)
78
(22)
(Con
duit
Hol
es -
2
Pla
ces)
Dia
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
A13-1
316
(351
)
12
(13)
B
5-1
4rdquoM
in
Cle
aran
ce
11-1
116
(297
)
38
(19)
14-3
16
(360
)13
-13
16(3
51)
Lef
t H
and
Do
or
op
en t
o 1
10deg
sho
wn
58
(15
9)S
top
Sex
Nu
ts(2
Pla
ces)
Left
Han
dD
oor
Rig
htH
and
Doo
r
1-1
2rdquo (
38m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
5-1
4rdquo (
133m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
axD
oo
r Th
ickn
ess
No
te D
oo
r m
ust
be
visi
ble
by
per
son
op
erat
ing
act
ivat
ion
sw
itch
(es)
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Sto
p (
Pu
sh)
Sid
e ap
plic
atio
n a
s sh
ow
n o
n t
his
te
mp
late
Page 15
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
3000 Highway 74 East bull Monroe NC 28112Tel (800)-438-1951 x4706 bull Fax (800)-338-0965
wwwnor tondoorcontrolscom
ASSA ABLOY
This PageLeft Blank
Page 16
ASSA ABLOY
1A Installation Sequence ContinuedStep 5 Mount track assembly to door using 3 14-20 screws amp sex nuts
with buffer assembly toward hinge Open part of track to face top of door
Step 6 Insert slide arm rod into slide arm tube setting the distance between the pinion square and the slide stud at 13-12rdquo (343) Install 964rdquo hex drive socket head screw from screw pack (See illustration below)
Step 7 Using an adjustable wrench rotate pinion 45deg toward hinge as shown below With the arm assembly parallel to the door secure arm to pinion when square of the pinion aligns with the square in the arm Secure with countersunk washer and 14-20 Flat Head Screw (with thread lock) provided Tighten screw with 716rdquo wrench or socket
Step 9to
increase door closing power Door control is shipped set at midpoint of power setting Maximum closing power can be achieved with 8 (360deg) clockwise turns of the power adjustment screw
Step 8 Insert arm stud into slide block in track assembly Secure by pushing in on the retainer clip that extends from the slide block in the track until it is flush with the slide block (see illustration below)
Adjust closing power of unit (See Fig 1) - Using a 18rdquo allen wrench turn the power adjustment shaft clockwise
Step 10 Adjust Hydraulic valves using a 18rdquo hex wrench to obtain proper door closing speeds See following illustrations Refer to Table 1 below for recommended minimum opening closing times per ANSIBHMA A15619
Note ADA requires that from an open position of 70deg the door will take at least 3 seconds to move to a point 3rdquo (75mm) from the latched position measured at the leading edge of the door
Closing Cycle ndash Make adjustments as necessary to the Sweep Speed S valve and Latch Speed L valve See Fig 2 below for location of valves Turn valves clockwise to reduce speed counter clockwise to increase speed
Opening Cycle ndash Adjust Backcheck B valve as necessary for hydraulic resistance to door opening in the backcheck range See illustration in Fig 2 for location of valve
NOTE Too much Backcheck B valve can affect the operation of the units pump preventing units from fully opening the door This valve may require fine tuning after all other adjustments have been made
2
1Attaching Arm Stud to Slide
Retainer Clip
18HexKey
SlowerClosing
FasterClosingClosing Cycle
Closed
10deg
egnaR hctaL
egnaR peewS
18HexKey
IncreaseCushion
DecreaseCushion
Sweep Valve
Latch Valve
BackcheckValve
Figure 2
Power Adjustment
18HexKey
IncreasePower
DecreasePower Figure 1
Opening Cycle
Backcheckgninep
O
13-12(343)
Note Center threaded hole of slider arm should align with seventh hole of the slider tube Stud in slider arm should point to same side as holes in slider tube (see illustration on Page 3)
RHDoor
LHDoor
RotatePinion
Pinion Flats
1A Installation Sequence ContinuedTable 1 - Minimum Opening Closing Times for ANSIBHMA A15619Door Weight in Pounds (kg)Door Leaf
Width -Inches (mm)
Matrix values are in seconds
Backcheck - adjust the backcheck valve to have a minimum opening time to backcheck or 80 degrees (whichever comes first) based on Table 1
Closing Time - adjust Latch and Sweep valves to have a minimum closing time from 90 degrees to Latch Check or 10 degrees (whichever comes first) based on Table 1
Page 5
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Door OpeningAngle
Dim ldquoArdquo Dim ldquoBrdquo
Up to 110deg
111deg to 170deg
12 (305)
9-12 (241) 13-14 (337)
15-34 (400)
Notesbull All dimensions are given in inches (mm)bull Thickness recommended for reinforcements in
hollow metal doors and frames is charted at the left of this page
bull Do not scale drawingbull Left hand door shownbull This template information based upon use of 5
(127mm) maximum width butt hinges or 34 (19mm) offset pivots A separate template will be supplied for other conditions
bull Maximum frame reveal is 7rdquo (178mm) for this application
bull Conduit hole nearest to hinge is suggested for 120 VAC power input
1-1116(43)
1-14(32)
1116(175)
1-34(44)
12-1516(329)
7-916(192)
13-716(341)
38(10)
CL Hinge or Pivot
14-20 Machine Screwsor No 14 Wood Screws
(6 Places)
78(22)
(Conduit Holes - 2 Places)
Dia
FrameRabbet
FrameStopSoffit
A
13-1316(351)
12(13)
B
5-14rdquoMin
Clearance
11-1116(297)
38(19)
14-316(360)
13-1316(351)
Left Hand Dooropen to 110deg shown
58(159)
Stop
Sex Nuts(2 Places)
2 Stop (Push) Side Mounting Instructions
2A Installation Sequence
LeftHandDoor
RightHandDoor
1-12rdquo (38mm)Min Frame Face
Frame Reveal
Do
or
5-14rdquo (133mm)Min CeilingClearance
1-34rdquo (44mm) Min2-14rdquo (57mm) Max
Door ThicknessFor frame reveals less than 3 (76mm) the arm adjusting rod can be field cut to a length of 9-12 (241mm) measured from centerline of connecting link bushing assembly Note Door must be visible by person operating activation switch(es)
Step 1 Determine hand of door from illustration on upper right of this page
Step 2 Using template above locate and prepare holes in the frame amp door
FrameA Prepare six (6) holes for 14-20 machine screws or No 14 x 2-34
(70mm) wood screws Blind rivet nuts (by others) are suggested for unreinforced hollow metal frames or for aluminum frames
B Concealed Wired Units Only Two (2) 78 (22mm) diameter holes for conduit for power input and for switchsensor wires
NOTE On new construction these holes will generally be drilled by the frame supplier at their shop or at the time the frame is installed in the wall
DoorC Prepare two (2) holes for 38 diameter sex nuts Standard units
are supplied with sex nuts and screws for 1-34 (44mm) thick door Sex nuts and screws for other door thicknesses are available to order
Step 3 Remove cover from the unit and set cover amp cover screws aside
Step 4 Mount unit to door frame Select A or B below
A Concealed Wired Units Only
B Surface Wired Units Only
Connect conduit to frame side of backplate Fasten unit to door frame (six screws)
Fasten unit to door frame (six screws) Mount conduit bracket (found in screw pack) to unit backplate with two screws provided Connect wiring conduit to bracket
Please verify desired mounting requires Stop (Push) Side
application as shown on this template
Page 6
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
2A Installation Sequence Continued
Step 5 Install main arm onto pinion shaft of unit at a 90deg angle to the door frame Align arm mark ldquoSrdquo with the flat corner of the pinion shaft square (See Fig 3 below)
Step 6 Secure main arm to pinion with 14-20 Flange Head Screw provided Tighten screw with 716 wrench or socket
Step 9to
increase door closing power Door control is shipped set at midpoint of power setting Maximum closing power can be achieved with 8 (360deg) clockwise turns of the power adjustment screw
Step 7 Mount arm shoe to door using 2 14-20 screws amp sex nuts provided with screw pack
Step 8 PRELOAD ARM (See Fig 4 below) Remove 14-20 hex head screw on adjusting rod and insert adjusting rod into arm slide Reinstall 14-20 screw and leave loose Rotate main arm in direction away from the hinge edge until the adjusting rod and arm slide are perpendicular (at a 90deg angle) to the door frame Tighten the 14-20 hex head screw on the adjusting rod to secure arm in this new position
Adjust closing power of unit (See Fig 5) - Using a 18rdquo allen wrench turn the power adjustment shaft clockwise
Step 10 Adjust Hydraulic valves using a 18rdquo hex wrench to obtain proper door closing speeds See following illustrations Refer to Table 1 on page 5 for recommended minimum opening closing times per ANSIBHMA A15619
Note ADA requires that from an open position of 70deg the door will take at least 3 seconds to move to a point 3rdquo (75mm) from the latched position measured at the leading edge of the door
Step 11 Make wiring connections using Wiring Instructions on Page below and on Page 8
Closing Cycle ndash Make adjustments as necessary to the Sweep Speed S valve and Latch Speed L valve See Fig 6 below for location of valves Turn valves clockwise to reduce speed counter clockwise to increase speed
Opening Cycle ndash Adjust Backcheck B valve as necessary for hydraulic resistance to door opening in the backcheck range See illustration at bottom of this page for location of valve
NOTE Too much Backcheck B valve can affect the operation of the units pump preventing units from fully opening the door This valve may require fine tuning after all other adjustments have been made
R
LYS
Z
Arm Mark Pinion Flat
Figure 3
AdjustingRod
ArmSlide
DoorShoe
MainArm
Figure 4Adjusting
Rod
ArmSlide
DoorShoe
MainArm
PowerAdjustment
18HexKey
IncreasePower
DecreasePower
Figure 5
18HexKey
SlowerClosing
FasterClosing Closing Cycle
Closed
10deg
egnaR hctaL
egnaR peewS
18HexKey
IncreaseCushion
DecreaseCushion
Opening Cycle
Backcheckgninep
O
Sweep ValveLatch Valve
BackcheckValve
Figure 8
Page 7
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Low VoltageControlWiring
IncomingPower
Optional Bracket(for surface wiring)
GroundLead
PowerLeads
GroundScrew(Green)
CableClamps Conduit
by Others(from top)
ldquoT1rdquo PowerInputTerminal
24
23
22
25
HOT
COM
Breaker Switch
T1 TerminalBlock
4 Final Electrical and Mechanical SetupA Confirm all mechanical adjustments have been made
and wiring connected per Page 7 and 8B Turn on facilityrsquos main circuit breakerC Turn power to unit on at the Unit Power Switch and
turn the Breaker Switch to ldquoRESETrdquo
D Using a short jumper cable jump terminals 1 and 2 see Fig 2 below to activate unit When door reaches 20deg switch Breaker Switch to ldquoOFFrdquo position cutting power to the unit Allow door to fully close (door may be manually pulled closed)
1234
1234
Figure 2
3 Input Power ConfigurationsCONCEALED WIRING SURFACE WIRING
Ground Wire Connection ndash Ground wire must be secured to backplate under head of (green) ground screw
Terminal Description
HOT
25
23
24
22
COM Common power lead
Hot power lead
Circuit Breaker
Switch
Circuit Breaker
Common connection to Circuit Breaker Inverter
Thread conduit fitting(s) into backplate as shown A second conduit fitting is required for low voltage control wiring CHECK LOCAL CODES Pull conduit out of header and attach to conduit fittings before mounting Secure operator to door frame Attach incoming ground wire to backplate with ground screw as illustrated in ldquoSurface Wiringrdquo illustration to the Right
Thread conduit fitting(s) into backplate as shown A second conduit fitting is required for low voltage control wiring CHECK LOCAL CODES Pull conduit out of header and attach to conduit fittings before mounting Secure operator to door frame Attach incoming ground wire to backplate with ground screw as illustrated below
Breaker Switch
Unit Power Switch
Page 8
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
4 Final Electrical and Mechanical Setup ContinuedE Adjust Closing Position Magnet (See Fig 3) - With
door in the closed position use finger to slide Closed Position Magnet so it aligns directly with the Reed Switch
F Adjust Open Position Magnet - Use fingers to slide
F cont Open Position Magnet 180deg from Open Position Magnet
G Flip Breaker Switch to ldquoRESETrdquo to turn power on Jump terminals 1 and 2 (as shown in Fig 2) to activate door Note open position of the door Allow door to close
H Use finger to readjust the Open Position Magnet to desired door open position
I Repeat Step G to verify door open position J Make all connections necessary for any accessories to
the 4-position Accessory Terminal (see Pages 10-11)K Make necessary adjustments to inverter (see Page 9)
Replace cover and cover screws
Reed Switch
Closed Position Magnet
Open PositionMagnet
Position Ring
Figure 3
Inverter Adjustmentsmiddot Based on function
adjustment desired use table above to determine which POT is to be adjusted
POT FUNCTIONDESCRIPTION
OBSTR SENS Obstruction Detection on Open CW - IncreaseCCW - Decrease
MDLY Motor Delay on Opening CW - IncreaseCCW - Decrease
P1 Closing Speed CW - IncreaseCCW - Decrease
HO TM Hold Open Time (5 - 30 Seconds) CW - IncreaseCCW - Decrease
P2 Opening Speed CW - IncreaseCCW - Decrease
HO TQMotor Torque at Hold Open Position
CW - IncreaseCCW - Decrease
ON
12
WARNING
120 HIGH VOLT POTENTIAL PRESENT MAKE SURE POWER IS TURNED OFF DURING
INSTALLATION PROCEDURE
Dip Switch Settings
1 Door Mounting -
2 Push Recognition -
ON - pullOFF - pushON - activeOFF - inactive
WARNINGElectric
Shock Risk
(Adjustments made in the shaded area should be performed by
Authorized Factory Personnel)
L2115Y
L1 115230VAC IN
MOTOR OUT
L2230Y
U
V
W
STATUS LEDS
HO TQHO TM
OBSTRSENS
P1
MDLY P2
16
COM
SNS
COM
PB
K1
K2
11
JMP503
NC
NO
TB501
PU
LL P
US
HSW501
ON
12
Inverter Details
Page 9
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Standard Function with Switches
1
2
3
4
1
2
3
4
Notes1Power input to Door
Operator Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
Wall Switch CardReader Key Switchetc
1
2
3
4
1
2
3
4Door 1 Door 2
Operationbull bull Activating either switch will
open both doors Door will close after hold open time delay has elapsed
Doors are normally closed
Wall Switch CardReader Key Switchetc
Normally Open Momentary dry contacts
Normally Open Momentary dry contacts
Radio Frequency Function Option
1 2 3 4
1 2 3 4
Optional Door 2
1 2 3 4
1 2 3 4
Door 1
Notes1Power input to Door Operator
Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
2 Radio Frequency Feature can be purchased as a separate kit
Operationbull
closedbull Activating wireless
switch or hand held wireless transmitter will open the door
bull Door will close after hold open delay elapses
Door is normally
120VAC
GroundC
OM
HO
TL N(AC) -V +V ADJ
+
11A 24V Power Supply12-24 VA
CD
CC
OM
NO
NC
Troubleshooting
Jump activation input
Change the setting of the ONOFF switch
Flip Door Mounting Dip Switch to other direction
Remove object
Re-time and re-install arm
Increase spring tension per preceding instructions
Remove object
Fault Possible reasons why RemediesExplanations
The door does not open- The motor does not start
Control switch is set to OFF position
Electrical power is missing the electrical Check power switch
Activation unit does not function- The motor starts Motor is driving in wrong direction
Something jammed beneath the door
Arm has come loose
The door does not close Spring tension too lowArm has come loose Re-time and re-install arm
Something jammed beneath the door
Circuit breaker is set to OFF position Reset circuit breaker to the ON position
Page 10
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Fail Secure Fail Safe Electric Strike Wiring
120VACSupplied byOthers- +
DC or ACOutput
AC
or
DC
Ele
ctric
Str
ike+
-
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating for strike interface 30VDC 1A or 125VAC 5A
Operationbull bull Activating switch will unlock the electric strike
and the door will automatically open Door will close after hold open time delay has elapsed
bull For Fail Secure Strike - The door will remain locked during power failure
bull For Fail Safe Strike - The door will remain unlocked during power failure
Door is normally closed and latched
1
2
3
4
1
2
3
4
JMP503
NC
NO
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
Fail Safe Electromagnetic Lock 24VDC Wiring
1
2
3
4
1
2
3
4
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
+-24VDC Electromagnetic Lock(Fail Safe)
Operationbull bull Activating switch will cut power to mag lock and the door will automatically
open Door will close after hold open time delay has elapsedbull The door will unlock during power failure
Door is normally closed and latched
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating 30VDC 1A or 125VAC 5A
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
JMP503
NC
NO
120VAC
GroundC
OM
HO
T
L N(AC) -V +V ADJ+
Optional 11A 24V Power Supply
Page 11
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Page 12
Troubleshooting
Red LEDBlue LED
Antenna Wire
Learnwo DelayButton
DelayPotentiometer(Time Adjustment)
Learn wDelay Button
DIP Switch
TerminalStrip
Problem The LED on my receiver is just flickering and Irsquom unable to program andor it wonrsquot workSolution You have a push plate stuck or faulty transmitter Disconnect each push plate until the LED goes out If LED
does not go out remove each transmitter battery until it does Replace the appropriate transmitterProblem Receiver intermittently doesnrsquot receive the transmitter(s) signal
Solution You may extend the receiver antenna wire only in multiples of 6-34rdquo (171) ie 675 x 4 = 27rdquo (686) of extended antenna wire
Removing Transmitter Code(s)
Single Transmitter CodeŸ Press both Delay and No Delay Buttons simultaneously until Red LED flashes once (approximately 1 second)Ÿ Press transmitter button twice within 10 seconds and the transmitter code will be deleted
All Transmitter CodesŸ Press and hold both Delay and No Delay Buttons simultaneously until Blue LED illuminates then release (approximately 10
seconds)
Push Plate Configuration
1 Before beginning it is easiest to have already prepared the installation of the push plate2 Connect the wires from the transmitter to the NO and COM contacts of the push platersquos switch3 Follow Steps 1 - 4 (Hand-Held Configuration) depress the push plate to activate the transmitter4 Attach the transmitter to the inside of the electrical box and complete the installation
Hand-Held Configuration
1 Set dip switches to the receiver to the desired activation cycle (dip switch 1 - Toggle or Pulse and dip switch 2 - 05s or 10s hold
2 Press either Learn w Delay Button or Learn wo Delay Button on the receiver depending on the activation requirements (if delay learn is selected adjust potentiometer to counterclockwise limit 0 second delay) Red LED on receiver will flash After learn cycle is complete adjust potentiometer to desired delay time (0 - 30 sec)
3 Depress transmitter button repeatedly until Blue LED on the receiver illuminates (indicating reception of signal from transmitter) NOTE Repeat Steps 2 - 3 to program additional transmitters
4 To test the system depress transmitter button (Red LED on Transmitter will illuminate) and observe that the Blue LED illuminates on the receiver This indicates that the relay has been activated
433MHz Receiver Userrsquos Guide
2OFFON
Description05s Hold Time10s Hold Time
FunctionRelay will remain active 05 sec after loss of activationRelay will remain active 10 sec after loss of activation
1OFF
ON
DescriptionPulse Relay
Toggle Relay
FunctionPress the transmitter once and the relay will be active momentarilyPress the transmitter once and the relay output is active indefinitely press it again and the relay will de-energize indefinitely
ON
1 2PU
L T
OG
05s
1
0s ON
1 2PU
L T
OG
05s
1
0sIn Toggle Setting (1-ON) the Hold Time is inactive Either setting for 2 dip switch will
have the same result
ON
1 2PU
L T
OG
05s
1
0s
05 second Pulse Setting
ON
1 2PU
L T
OG
05s
1
0s
10 second Pulse Setting
ŸAlways stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door
ŸEnsure compliance with all applicable safety standards upon completion of installation
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
This PageLeft Blank
Page 13
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Hinge (Pull) SideŸ Do not scale drawingŸ Right hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
No
te D
oo
r m
ust
be
visi
ble
by
per
son
o
per
atin
g a
ctiv
atio
n s
wit
ch(e
s)
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Up
to 1
10deg
111deg
to 1
80deg
15-1
2 (
394)
13-1
4 (
337)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull T
hick
ness
rec
omm
ende
d fo
r re
info
rcem
ents
in h
ollo
w
met
al d
oors
and
fram
es is
cha
rted
on
Pag
e 2
bull D
o no
t sca
le d
raw
ing
bull R
ight
han
d do
or s
how
nbull
Thi
s te
mpl
ate
info
rmat
ion
base
d up
on u
se o
f 5
(127
mm
) m
axim
um w
idth
but
t hin
ges
A s
epar
ate
tem
plat
e is
req
uire
d fo
r ot
her
cond
ition
sbull
Max
imum
fram
e re
veal
is 6
-78
rdquo (17
5mm
) fo
r th
is
appl
icat
ion
bull C
ondu
it ho
le n
eare
st th
e hi
nge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
2rdquo (
51m
m)
Min
F
ram
e Fa
ce
1-1
8rdquo(2
9)
1-1
4(3
2)1-
716
(37)
11(2
79)
22(5
59)
7-9
16(1
92)
13-7
16
(341
)
1-1
8(2
9)
C LH
inge
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)7
8 (2
3) D
ia
(2 P
lace
s)
38
Dia
S
ex N
uts
(3 P
lace
s)
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
3(7
6)
13-1
316
(350
)
12
(13)
A
11-1
116
(297
)
6rdquo
(152
mm
)M
in
Cle
aran
ce
14-3
16
(360
)
12-1
516
(329
)13
-13
16(3
51)
Rig
ht
Han
d D
oo
ro
pen
ing
to
110
deg sh
ow
n
58
(15
9)S
top
Left
Han
dD
oor
Rig
htH
and
Doo
r
2rdquo (
51m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
6rdquo (
152m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
ax
Do
or T
hic
knes
s
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Hin
ge
(Pu
ll) S
ide
app
licat
ion
as
sho
wn
on
th
is
tem
pla
te
Page 14
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Stop (Push) SideŸ Do not scale drawingŸ Left hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Dim
ldquoB
rdquo
Up
to 1
10deg
111deg
to 1
70deg
12 (
305)
9-1
2 (2
41)
13-1
4 (
337)
15-3
4 (
400)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull Thi
ckne
ss r
ecom
men
ded
for
rein
forc
emen
ts in
ho
llow
met
al d
oors
and
fram
es is
cha
rted
at t
he
left
of th
is p
age
bull D
o no
t sca
le d
raw
ing
bull Le
ft ha
nd d
oor
show
nbull T
his
tem
plat
e in
form
atio
n ba
sed
upon
use
of 5
(1
27m
m)
max
imum
wid
th b
utt h
inge
s or
34
(1
9mm
) of
fset
piv
ots
A s
epar
ate
tem
plat
e w
ill
be s
uppl
ied
for
othe
r co
nditi
ons
bull M
axim
um fr
ame
reve
al is
7rdquo (
178m
m)
for
this
ap
plic
atio
nbull
Con
duit
hole
nea
rest
to h
inge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
1-11
16
(43)
1-1
4(3
2)11
16
(17
5)
1-3
4(4
4)
12-1
516
(329
)
7-9
16(1
92)
13-7
16
(341
)
38
(10)
C LH
inge
or
Piv
ot
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)
78
(22)
(Con
duit
Hol
es -
2
Pla
ces)
Dia
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
A13-1
316
(351
)
12
(13)
B
5-1
4rdquoM
in
Cle
aran
ce
11-1
116
(297
)
38
(19)
14-3
16
(360
)13
-13
16(3
51)
Lef
t H
and
Do
or
op
en t
o 1
10deg
sho
wn
58
(15
9)S
top
Sex
Nu
ts(2
Pla
ces)
Left
Han
dD
oor
Rig
htH
and
Doo
r
1-1
2rdquo (
38m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
5-1
4rdquo (
133m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
axD
oo
r Th
ickn
ess
No
te D
oo
r m
ust
be
visi
ble
by
per
son
op
erat
ing
act
ivat
ion
sw
itch
(es)
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Sto
p (
Pu
sh)
Sid
e ap
plic
atio
n a
s sh
ow
n o
n t
his
te
mp
late
Page 15
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
3000 Highway 74 East bull Monroe NC 28112Tel (800)-438-1951 x4706 bull Fax (800)-338-0965
wwwnor tondoorcontrolscom
ASSA ABLOY
This PageLeft Blank
Page 16
ASSA ABLOY
Door OpeningAngle
Dim ldquoArdquo Dim ldquoBrdquo
Up to 110deg
111deg to 170deg
12 (305)
9-12 (241) 13-14 (337)
15-34 (400)
Notesbull All dimensions are given in inches (mm)bull Thickness recommended for reinforcements in
hollow metal doors and frames is charted at the left of this page
bull Do not scale drawingbull Left hand door shownbull This template information based upon use of 5
(127mm) maximum width butt hinges or 34 (19mm) offset pivots A separate template will be supplied for other conditions
bull Maximum frame reveal is 7rdquo (178mm) for this application
bull Conduit hole nearest to hinge is suggested for 120 VAC power input
1-1116(43)
1-14(32)
1116(175)
1-34(44)
12-1516(329)
7-916(192)
13-716(341)
38(10)
CL Hinge or Pivot
14-20 Machine Screwsor No 14 Wood Screws
(6 Places)
78(22)
(Conduit Holes - 2 Places)
Dia
FrameRabbet
FrameStopSoffit
A
13-1316(351)
12(13)
B
5-14rdquoMin
Clearance
11-1116(297)
38(19)
14-316(360)
13-1316(351)
Left Hand Dooropen to 110deg shown
58(159)
Stop
Sex Nuts(2 Places)
2 Stop (Push) Side Mounting Instructions
2A Installation Sequence
LeftHandDoor
RightHandDoor
1-12rdquo (38mm)Min Frame Face
Frame Reveal
Do
or
5-14rdquo (133mm)Min CeilingClearance
1-34rdquo (44mm) Min2-14rdquo (57mm) Max
Door ThicknessFor frame reveals less than 3 (76mm) the arm adjusting rod can be field cut to a length of 9-12 (241mm) measured from centerline of connecting link bushing assembly Note Door must be visible by person operating activation switch(es)
Step 1 Determine hand of door from illustration on upper right of this page
Step 2 Using template above locate and prepare holes in the frame amp door
FrameA Prepare six (6) holes for 14-20 machine screws or No 14 x 2-34
(70mm) wood screws Blind rivet nuts (by others) are suggested for unreinforced hollow metal frames or for aluminum frames
B Concealed Wired Units Only Two (2) 78 (22mm) diameter holes for conduit for power input and for switchsensor wires
NOTE On new construction these holes will generally be drilled by the frame supplier at their shop or at the time the frame is installed in the wall
DoorC Prepare two (2) holes for 38 diameter sex nuts Standard units
are supplied with sex nuts and screws for 1-34 (44mm) thick door Sex nuts and screws for other door thicknesses are available to order
Step 3 Remove cover from the unit and set cover amp cover screws aside
Step 4 Mount unit to door frame Select A or B below
A Concealed Wired Units Only
B Surface Wired Units Only
Connect conduit to frame side of backplate Fasten unit to door frame (six screws)
Fasten unit to door frame (six screws) Mount conduit bracket (found in screw pack) to unit backplate with two screws provided Connect wiring conduit to bracket
Please verify desired mounting requires Stop (Push) Side
application as shown on this template
Page 6
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
2A Installation Sequence Continued
Step 5 Install main arm onto pinion shaft of unit at a 90deg angle to the door frame Align arm mark ldquoSrdquo with the flat corner of the pinion shaft square (See Fig 3 below)
Step 6 Secure main arm to pinion with 14-20 Flange Head Screw provided Tighten screw with 716 wrench or socket
Step 9to
increase door closing power Door control is shipped set at midpoint of power setting Maximum closing power can be achieved with 8 (360deg) clockwise turns of the power adjustment screw
Step 7 Mount arm shoe to door using 2 14-20 screws amp sex nuts provided with screw pack
Step 8 PRELOAD ARM (See Fig 4 below) Remove 14-20 hex head screw on adjusting rod and insert adjusting rod into arm slide Reinstall 14-20 screw and leave loose Rotate main arm in direction away from the hinge edge until the adjusting rod and arm slide are perpendicular (at a 90deg angle) to the door frame Tighten the 14-20 hex head screw on the adjusting rod to secure arm in this new position
Adjust closing power of unit (See Fig 5) - Using a 18rdquo allen wrench turn the power adjustment shaft clockwise
Step 10 Adjust Hydraulic valves using a 18rdquo hex wrench to obtain proper door closing speeds See following illustrations Refer to Table 1 on page 5 for recommended minimum opening closing times per ANSIBHMA A15619
Note ADA requires that from an open position of 70deg the door will take at least 3 seconds to move to a point 3rdquo (75mm) from the latched position measured at the leading edge of the door
Step 11 Make wiring connections using Wiring Instructions on Page below and on Page 8
Closing Cycle ndash Make adjustments as necessary to the Sweep Speed S valve and Latch Speed L valve See Fig 6 below for location of valves Turn valves clockwise to reduce speed counter clockwise to increase speed
Opening Cycle ndash Adjust Backcheck B valve as necessary for hydraulic resistance to door opening in the backcheck range See illustration at bottom of this page for location of valve
NOTE Too much Backcheck B valve can affect the operation of the units pump preventing units from fully opening the door This valve may require fine tuning after all other adjustments have been made
R
LYS
Z
Arm Mark Pinion Flat
Figure 3
AdjustingRod
ArmSlide
DoorShoe
MainArm
Figure 4Adjusting
Rod
ArmSlide
DoorShoe
MainArm
PowerAdjustment
18HexKey
IncreasePower
DecreasePower
Figure 5
18HexKey
SlowerClosing
FasterClosing Closing Cycle
Closed
10deg
egnaR hctaL
egnaR peewS
18HexKey
IncreaseCushion
DecreaseCushion
Opening Cycle
Backcheckgninep
O
Sweep ValveLatch Valve
BackcheckValve
Figure 8
Page 7
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Low VoltageControlWiring
IncomingPower
Optional Bracket(for surface wiring)
GroundLead
PowerLeads
GroundScrew(Green)
CableClamps Conduit
by Others(from top)
ldquoT1rdquo PowerInputTerminal
24
23
22
25
HOT
COM
Breaker Switch
T1 TerminalBlock
4 Final Electrical and Mechanical SetupA Confirm all mechanical adjustments have been made
and wiring connected per Page 7 and 8B Turn on facilityrsquos main circuit breakerC Turn power to unit on at the Unit Power Switch and
turn the Breaker Switch to ldquoRESETrdquo
D Using a short jumper cable jump terminals 1 and 2 see Fig 2 below to activate unit When door reaches 20deg switch Breaker Switch to ldquoOFFrdquo position cutting power to the unit Allow door to fully close (door may be manually pulled closed)
1234
1234
Figure 2
3 Input Power ConfigurationsCONCEALED WIRING SURFACE WIRING
Ground Wire Connection ndash Ground wire must be secured to backplate under head of (green) ground screw
Terminal Description
HOT
25
23
24
22
COM Common power lead
Hot power lead
Circuit Breaker
Switch
Circuit Breaker
Common connection to Circuit Breaker Inverter
Thread conduit fitting(s) into backplate as shown A second conduit fitting is required for low voltage control wiring CHECK LOCAL CODES Pull conduit out of header and attach to conduit fittings before mounting Secure operator to door frame Attach incoming ground wire to backplate with ground screw as illustrated in ldquoSurface Wiringrdquo illustration to the Right
Thread conduit fitting(s) into backplate as shown A second conduit fitting is required for low voltage control wiring CHECK LOCAL CODES Pull conduit out of header and attach to conduit fittings before mounting Secure operator to door frame Attach incoming ground wire to backplate with ground screw as illustrated below
Breaker Switch
Unit Power Switch
Page 8
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
4 Final Electrical and Mechanical Setup ContinuedE Adjust Closing Position Magnet (See Fig 3) - With
door in the closed position use finger to slide Closed Position Magnet so it aligns directly with the Reed Switch
F Adjust Open Position Magnet - Use fingers to slide
F cont Open Position Magnet 180deg from Open Position Magnet
G Flip Breaker Switch to ldquoRESETrdquo to turn power on Jump terminals 1 and 2 (as shown in Fig 2) to activate door Note open position of the door Allow door to close
H Use finger to readjust the Open Position Magnet to desired door open position
I Repeat Step G to verify door open position J Make all connections necessary for any accessories to
the 4-position Accessory Terminal (see Pages 10-11)K Make necessary adjustments to inverter (see Page 9)
Replace cover and cover screws
Reed Switch
Closed Position Magnet
Open PositionMagnet
Position Ring
Figure 3
Inverter Adjustmentsmiddot Based on function
adjustment desired use table above to determine which POT is to be adjusted
POT FUNCTIONDESCRIPTION
OBSTR SENS Obstruction Detection on Open CW - IncreaseCCW - Decrease
MDLY Motor Delay on Opening CW - IncreaseCCW - Decrease
P1 Closing Speed CW - IncreaseCCW - Decrease
HO TM Hold Open Time (5 - 30 Seconds) CW - IncreaseCCW - Decrease
P2 Opening Speed CW - IncreaseCCW - Decrease
HO TQMotor Torque at Hold Open Position
CW - IncreaseCCW - Decrease
ON
12
WARNING
120 HIGH VOLT POTENTIAL PRESENT MAKE SURE POWER IS TURNED OFF DURING
INSTALLATION PROCEDURE
Dip Switch Settings
1 Door Mounting -
2 Push Recognition -
ON - pullOFF - pushON - activeOFF - inactive
WARNINGElectric
Shock Risk
(Adjustments made in the shaded area should be performed by
Authorized Factory Personnel)
L2115Y
L1 115230VAC IN
MOTOR OUT
L2230Y
U
V
W
STATUS LEDS
HO TQHO TM
OBSTRSENS
P1
MDLY P2
16
COM
SNS
COM
PB
K1
K2
11
JMP503
NC
NO
TB501
PU
LL P
US
HSW501
ON
12
Inverter Details
Page 9
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Standard Function with Switches
1
2
3
4
1
2
3
4
Notes1Power input to Door
Operator Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
Wall Switch CardReader Key Switchetc
1
2
3
4
1
2
3
4Door 1 Door 2
Operationbull bull Activating either switch will
open both doors Door will close after hold open time delay has elapsed
Doors are normally closed
Wall Switch CardReader Key Switchetc
Normally Open Momentary dry contacts
Normally Open Momentary dry contacts
Radio Frequency Function Option
1 2 3 4
1 2 3 4
Optional Door 2
1 2 3 4
1 2 3 4
Door 1
Notes1Power input to Door Operator
Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
2 Radio Frequency Feature can be purchased as a separate kit
Operationbull
closedbull Activating wireless
switch or hand held wireless transmitter will open the door
bull Door will close after hold open delay elapses
Door is normally
120VAC
GroundC
OM
HO
TL N(AC) -V +V ADJ
+
11A 24V Power Supply12-24 VA
CD
CC
OM
NO
NC
Troubleshooting
Jump activation input
Change the setting of the ONOFF switch
Flip Door Mounting Dip Switch to other direction
Remove object
Re-time and re-install arm
Increase spring tension per preceding instructions
Remove object
Fault Possible reasons why RemediesExplanations
The door does not open- The motor does not start
Control switch is set to OFF position
Electrical power is missing the electrical Check power switch
Activation unit does not function- The motor starts Motor is driving in wrong direction
Something jammed beneath the door
Arm has come loose
The door does not close Spring tension too lowArm has come loose Re-time and re-install arm
Something jammed beneath the door
Circuit breaker is set to OFF position Reset circuit breaker to the ON position
Page 10
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Fail Secure Fail Safe Electric Strike Wiring
120VACSupplied byOthers- +
DC or ACOutput
AC
or
DC
Ele
ctric
Str
ike+
-
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating for strike interface 30VDC 1A or 125VAC 5A
Operationbull bull Activating switch will unlock the electric strike
and the door will automatically open Door will close after hold open time delay has elapsed
bull For Fail Secure Strike - The door will remain locked during power failure
bull For Fail Safe Strike - The door will remain unlocked during power failure
Door is normally closed and latched
1
2
3
4
1
2
3
4
JMP503
NC
NO
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
Fail Safe Electromagnetic Lock 24VDC Wiring
1
2
3
4
1
2
3
4
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
+-24VDC Electromagnetic Lock(Fail Safe)
Operationbull bull Activating switch will cut power to mag lock and the door will automatically
open Door will close after hold open time delay has elapsedbull The door will unlock during power failure
Door is normally closed and latched
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating 30VDC 1A or 125VAC 5A
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
JMP503
NC
NO
120VAC
GroundC
OM
HO
T
L N(AC) -V +V ADJ+
Optional 11A 24V Power Supply
Page 11
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Page 12
Troubleshooting
Red LEDBlue LED
Antenna Wire
Learnwo DelayButton
DelayPotentiometer(Time Adjustment)
Learn wDelay Button
DIP Switch
TerminalStrip
Problem The LED on my receiver is just flickering and Irsquom unable to program andor it wonrsquot workSolution You have a push plate stuck or faulty transmitter Disconnect each push plate until the LED goes out If LED
does not go out remove each transmitter battery until it does Replace the appropriate transmitterProblem Receiver intermittently doesnrsquot receive the transmitter(s) signal
Solution You may extend the receiver antenna wire only in multiples of 6-34rdquo (171) ie 675 x 4 = 27rdquo (686) of extended antenna wire
Removing Transmitter Code(s)
Single Transmitter CodeŸ Press both Delay and No Delay Buttons simultaneously until Red LED flashes once (approximately 1 second)Ÿ Press transmitter button twice within 10 seconds and the transmitter code will be deleted
All Transmitter CodesŸ Press and hold both Delay and No Delay Buttons simultaneously until Blue LED illuminates then release (approximately 10
seconds)
Push Plate Configuration
1 Before beginning it is easiest to have already prepared the installation of the push plate2 Connect the wires from the transmitter to the NO and COM contacts of the push platersquos switch3 Follow Steps 1 - 4 (Hand-Held Configuration) depress the push plate to activate the transmitter4 Attach the transmitter to the inside of the electrical box and complete the installation
Hand-Held Configuration
1 Set dip switches to the receiver to the desired activation cycle (dip switch 1 - Toggle or Pulse and dip switch 2 - 05s or 10s hold
2 Press either Learn w Delay Button or Learn wo Delay Button on the receiver depending on the activation requirements (if delay learn is selected adjust potentiometer to counterclockwise limit 0 second delay) Red LED on receiver will flash After learn cycle is complete adjust potentiometer to desired delay time (0 - 30 sec)
3 Depress transmitter button repeatedly until Blue LED on the receiver illuminates (indicating reception of signal from transmitter) NOTE Repeat Steps 2 - 3 to program additional transmitters
4 To test the system depress transmitter button (Red LED on Transmitter will illuminate) and observe that the Blue LED illuminates on the receiver This indicates that the relay has been activated
433MHz Receiver Userrsquos Guide
2OFFON
Description05s Hold Time10s Hold Time
FunctionRelay will remain active 05 sec after loss of activationRelay will remain active 10 sec after loss of activation
1OFF
ON
DescriptionPulse Relay
Toggle Relay
FunctionPress the transmitter once and the relay will be active momentarilyPress the transmitter once and the relay output is active indefinitely press it again and the relay will de-energize indefinitely
ON
1 2PU
L T
OG
05s
1
0s ON
1 2PU
L T
OG
05s
1
0sIn Toggle Setting (1-ON) the Hold Time is inactive Either setting for 2 dip switch will
have the same result
ON
1 2PU
L T
OG
05s
1
0s
05 second Pulse Setting
ON
1 2PU
L T
OG
05s
1
0s
10 second Pulse Setting
ŸAlways stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door
ŸEnsure compliance with all applicable safety standards upon completion of installation
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
This PageLeft Blank
Page 13
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Hinge (Pull) SideŸ Do not scale drawingŸ Right hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
No
te D
oo
r m
ust
be
visi
ble
by
per
son
o
per
atin
g a
ctiv
atio
n s
wit
ch(e
s)
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Up
to 1
10deg
111deg
to 1
80deg
15-1
2 (
394)
13-1
4 (
337)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull T
hick
ness
rec
omm
ende
d fo
r re
info
rcem
ents
in h
ollo
w
met
al d
oors
and
fram
es is
cha
rted
on
Pag
e 2
bull D
o no
t sca
le d
raw
ing
bull R
ight
han
d do
or s
how
nbull
Thi
s te
mpl
ate
info
rmat
ion
base
d up
on u
se o
f 5
(127
mm
) m
axim
um w
idth
but
t hin
ges
A s
epar
ate
tem
plat
e is
req
uire
d fo
r ot
her
cond
ition
sbull
Max
imum
fram
e re
veal
is 6
-78
rdquo (17
5mm
) fo
r th
is
appl
icat
ion
bull C
ondu
it ho
le n
eare
st th
e hi
nge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
2rdquo (
51m
m)
Min
F
ram
e Fa
ce
1-1
8rdquo(2
9)
1-1
4(3
2)1-
716
(37)
11(2
79)
22(5
59)
7-9
16(1
92)
13-7
16
(341
)
1-1
8(2
9)
C LH
inge
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)7
8 (2
3) D
ia
(2 P
lace
s)
38
Dia
S
ex N
uts
(3 P
lace
s)
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
3(7
6)
13-1
316
(350
)
12
(13)
A
11-1
116
(297
)
6rdquo
(152
mm
)M
in
Cle
aran
ce
14-3
16
(360
)
12-1
516
(329
)13
-13
16(3
51)
Rig
ht
Han
d D
oo
ro
pen
ing
to
110
deg sh
ow
n
58
(15
9)S
top
Left
Han
dD
oor
Rig
htH
and
Doo
r
2rdquo (
51m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
6rdquo (
152m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
ax
Do
or T
hic
knes
s
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Hin
ge
(Pu
ll) S
ide
app
licat
ion
as
sho
wn
on
th
is
tem
pla
te
Page 14
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Stop (Push) SideŸ Do not scale drawingŸ Left hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Dim
ldquoB
rdquo
Up
to 1
10deg
111deg
to 1
70deg
12 (
305)
9-1
2 (2
41)
13-1
4 (
337)
15-3
4 (
400)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull Thi
ckne
ss r
ecom
men
ded
for
rein
forc
emen
ts in
ho
llow
met
al d
oors
and
fram
es is
cha
rted
at t
he
left
of th
is p
age
bull D
o no
t sca
le d
raw
ing
bull Le
ft ha
nd d
oor
show
nbull T
his
tem
plat
e in
form
atio
n ba
sed
upon
use
of 5
(1
27m
m)
max
imum
wid
th b
utt h
inge
s or
34
(1
9mm
) of
fset
piv
ots
A s
epar
ate
tem
plat
e w
ill
be s
uppl
ied
for
othe
r co
nditi
ons
bull M
axim
um fr
ame
reve
al is
7rdquo (
178m
m)
for
this
ap
plic
atio
nbull
Con
duit
hole
nea
rest
to h
inge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
1-11
16
(43)
1-1
4(3
2)11
16
(17
5)
1-3
4(4
4)
12-1
516
(329
)
7-9
16(1
92)
13-7
16
(341
)
38
(10)
C LH
inge
or
Piv
ot
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)
78
(22)
(Con
duit
Hol
es -
2
Pla
ces)
Dia
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
A13-1
316
(351
)
12
(13)
B
5-1
4rdquoM
in
Cle
aran
ce
11-1
116
(297
)
38
(19)
14-3
16
(360
)13
-13
16(3
51)
Lef
t H
and
Do
or
op
en t
o 1
10deg
sho
wn
58
(15
9)S
top
Sex
Nu
ts(2
Pla
ces)
Left
Han
dD
oor
Rig
htH
and
Doo
r
1-1
2rdquo (
38m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
5-1
4rdquo (
133m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
axD
oo
r Th
ickn
ess
No
te D
oo
r m
ust
be
visi
ble
by
per
son
op
erat
ing
act
ivat
ion
sw
itch
(es)
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Sto
p (
Pu
sh)
Sid
e ap
plic
atio
n a
s sh
ow
n o
n t
his
te
mp
late
Page 15
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
3000 Highway 74 East bull Monroe NC 28112Tel (800)-438-1951 x4706 bull Fax (800)-338-0965
wwwnor tondoorcontrolscom
ASSA ABLOY
This PageLeft Blank
Page 16
ASSA ABLOY
2A Installation Sequence Continued
Step 5 Install main arm onto pinion shaft of unit at a 90deg angle to the door frame Align arm mark ldquoSrdquo with the flat corner of the pinion shaft square (See Fig 3 below)
Step 6 Secure main arm to pinion with 14-20 Flange Head Screw provided Tighten screw with 716 wrench or socket
Step 9to
increase door closing power Door control is shipped set at midpoint of power setting Maximum closing power can be achieved with 8 (360deg) clockwise turns of the power adjustment screw
Step 7 Mount arm shoe to door using 2 14-20 screws amp sex nuts provided with screw pack
Step 8 PRELOAD ARM (See Fig 4 below) Remove 14-20 hex head screw on adjusting rod and insert adjusting rod into arm slide Reinstall 14-20 screw and leave loose Rotate main arm in direction away from the hinge edge until the adjusting rod and arm slide are perpendicular (at a 90deg angle) to the door frame Tighten the 14-20 hex head screw on the adjusting rod to secure arm in this new position
Adjust closing power of unit (See Fig 5) - Using a 18rdquo allen wrench turn the power adjustment shaft clockwise
Step 10 Adjust Hydraulic valves using a 18rdquo hex wrench to obtain proper door closing speeds See following illustrations Refer to Table 1 on page 5 for recommended minimum opening closing times per ANSIBHMA A15619
Note ADA requires that from an open position of 70deg the door will take at least 3 seconds to move to a point 3rdquo (75mm) from the latched position measured at the leading edge of the door
Step 11 Make wiring connections using Wiring Instructions on Page below and on Page 8
Closing Cycle ndash Make adjustments as necessary to the Sweep Speed S valve and Latch Speed L valve See Fig 6 below for location of valves Turn valves clockwise to reduce speed counter clockwise to increase speed
Opening Cycle ndash Adjust Backcheck B valve as necessary for hydraulic resistance to door opening in the backcheck range See illustration at bottom of this page for location of valve
NOTE Too much Backcheck B valve can affect the operation of the units pump preventing units from fully opening the door This valve may require fine tuning after all other adjustments have been made
R
LYS
Z
Arm Mark Pinion Flat
Figure 3
AdjustingRod
ArmSlide
DoorShoe
MainArm
Figure 4Adjusting
Rod
ArmSlide
DoorShoe
MainArm
PowerAdjustment
18HexKey
IncreasePower
DecreasePower
Figure 5
18HexKey
SlowerClosing
FasterClosing Closing Cycle
Closed
10deg
egnaR hctaL
egnaR peewS
18HexKey
IncreaseCushion
DecreaseCushion
Opening Cycle
Backcheckgninep
O
Sweep ValveLatch Valve
BackcheckValve
Figure 8
Page 7
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Low VoltageControlWiring
IncomingPower
Optional Bracket(for surface wiring)
GroundLead
PowerLeads
GroundScrew(Green)
CableClamps Conduit
by Others(from top)
ldquoT1rdquo PowerInputTerminal
24
23
22
25
HOT
COM
Breaker Switch
T1 TerminalBlock
4 Final Electrical and Mechanical SetupA Confirm all mechanical adjustments have been made
and wiring connected per Page 7 and 8B Turn on facilityrsquos main circuit breakerC Turn power to unit on at the Unit Power Switch and
turn the Breaker Switch to ldquoRESETrdquo
D Using a short jumper cable jump terminals 1 and 2 see Fig 2 below to activate unit When door reaches 20deg switch Breaker Switch to ldquoOFFrdquo position cutting power to the unit Allow door to fully close (door may be manually pulled closed)
1234
1234
Figure 2
3 Input Power ConfigurationsCONCEALED WIRING SURFACE WIRING
Ground Wire Connection ndash Ground wire must be secured to backplate under head of (green) ground screw
Terminal Description
HOT
25
23
24
22
COM Common power lead
Hot power lead
Circuit Breaker
Switch
Circuit Breaker
Common connection to Circuit Breaker Inverter
Thread conduit fitting(s) into backplate as shown A second conduit fitting is required for low voltage control wiring CHECK LOCAL CODES Pull conduit out of header and attach to conduit fittings before mounting Secure operator to door frame Attach incoming ground wire to backplate with ground screw as illustrated in ldquoSurface Wiringrdquo illustration to the Right
Thread conduit fitting(s) into backplate as shown A second conduit fitting is required for low voltage control wiring CHECK LOCAL CODES Pull conduit out of header and attach to conduit fittings before mounting Secure operator to door frame Attach incoming ground wire to backplate with ground screw as illustrated below
Breaker Switch
Unit Power Switch
Page 8
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
4 Final Electrical and Mechanical Setup ContinuedE Adjust Closing Position Magnet (See Fig 3) - With
door in the closed position use finger to slide Closed Position Magnet so it aligns directly with the Reed Switch
F Adjust Open Position Magnet - Use fingers to slide
F cont Open Position Magnet 180deg from Open Position Magnet
G Flip Breaker Switch to ldquoRESETrdquo to turn power on Jump terminals 1 and 2 (as shown in Fig 2) to activate door Note open position of the door Allow door to close
H Use finger to readjust the Open Position Magnet to desired door open position
I Repeat Step G to verify door open position J Make all connections necessary for any accessories to
the 4-position Accessory Terminal (see Pages 10-11)K Make necessary adjustments to inverter (see Page 9)
Replace cover and cover screws
Reed Switch
Closed Position Magnet
Open PositionMagnet
Position Ring
Figure 3
Inverter Adjustmentsmiddot Based on function
adjustment desired use table above to determine which POT is to be adjusted
POT FUNCTIONDESCRIPTION
OBSTR SENS Obstruction Detection on Open CW - IncreaseCCW - Decrease
MDLY Motor Delay on Opening CW - IncreaseCCW - Decrease
P1 Closing Speed CW - IncreaseCCW - Decrease
HO TM Hold Open Time (5 - 30 Seconds) CW - IncreaseCCW - Decrease
P2 Opening Speed CW - IncreaseCCW - Decrease
HO TQMotor Torque at Hold Open Position
CW - IncreaseCCW - Decrease
ON
12
WARNING
120 HIGH VOLT POTENTIAL PRESENT MAKE SURE POWER IS TURNED OFF DURING
INSTALLATION PROCEDURE
Dip Switch Settings
1 Door Mounting -
2 Push Recognition -
ON - pullOFF - pushON - activeOFF - inactive
WARNINGElectric
Shock Risk
(Adjustments made in the shaded area should be performed by
Authorized Factory Personnel)
L2115Y
L1 115230VAC IN
MOTOR OUT
L2230Y
U
V
W
STATUS LEDS
HO TQHO TM
OBSTRSENS
P1
MDLY P2
16
COM
SNS
COM
PB
K1
K2
11
JMP503
NC
NO
TB501
PU
LL P
US
HSW501
ON
12
Inverter Details
Page 9
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Standard Function with Switches
1
2
3
4
1
2
3
4
Notes1Power input to Door
Operator Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
Wall Switch CardReader Key Switchetc
1
2
3
4
1
2
3
4Door 1 Door 2
Operationbull bull Activating either switch will
open both doors Door will close after hold open time delay has elapsed
Doors are normally closed
Wall Switch CardReader Key Switchetc
Normally Open Momentary dry contacts
Normally Open Momentary dry contacts
Radio Frequency Function Option
1 2 3 4
1 2 3 4
Optional Door 2
1 2 3 4
1 2 3 4
Door 1
Notes1Power input to Door Operator
Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
2 Radio Frequency Feature can be purchased as a separate kit
Operationbull
closedbull Activating wireless
switch or hand held wireless transmitter will open the door
bull Door will close after hold open delay elapses
Door is normally
120VAC
GroundC
OM
HO
TL N(AC) -V +V ADJ
+
11A 24V Power Supply12-24 VA
CD
CC
OM
NO
NC
Troubleshooting
Jump activation input
Change the setting of the ONOFF switch
Flip Door Mounting Dip Switch to other direction
Remove object
Re-time and re-install arm
Increase spring tension per preceding instructions
Remove object
Fault Possible reasons why RemediesExplanations
The door does not open- The motor does not start
Control switch is set to OFF position
Electrical power is missing the electrical Check power switch
Activation unit does not function- The motor starts Motor is driving in wrong direction
Something jammed beneath the door
Arm has come loose
The door does not close Spring tension too lowArm has come loose Re-time and re-install arm
Something jammed beneath the door
Circuit breaker is set to OFF position Reset circuit breaker to the ON position
Page 10
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Fail Secure Fail Safe Electric Strike Wiring
120VACSupplied byOthers- +
DC or ACOutput
AC
or
DC
Ele
ctric
Str
ike+
-
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating for strike interface 30VDC 1A or 125VAC 5A
Operationbull bull Activating switch will unlock the electric strike
and the door will automatically open Door will close after hold open time delay has elapsed
bull For Fail Secure Strike - The door will remain locked during power failure
bull For Fail Safe Strike - The door will remain unlocked during power failure
Door is normally closed and latched
1
2
3
4
1
2
3
4
JMP503
NC
NO
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
Fail Safe Electromagnetic Lock 24VDC Wiring
1
2
3
4
1
2
3
4
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
+-24VDC Electromagnetic Lock(Fail Safe)
Operationbull bull Activating switch will cut power to mag lock and the door will automatically
open Door will close after hold open time delay has elapsedbull The door will unlock during power failure
Door is normally closed and latched
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating 30VDC 1A or 125VAC 5A
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
JMP503
NC
NO
120VAC
GroundC
OM
HO
T
L N(AC) -V +V ADJ+
Optional 11A 24V Power Supply
Page 11
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Page 12
Troubleshooting
Red LEDBlue LED
Antenna Wire
Learnwo DelayButton
DelayPotentiometer(Time Adjustment)
Learn wDelay Button
DIP Switch
TerminalStrip
Problem The LED on my receiver is just flickering and Irsquom unable to program andor it wonrsquot workSolution You have a push plate stuck or faulty transmitter Disconnect each push plate until the LED goes out If LED
does not go out remove each transmitter battery until it does Replace the appropriate transmitterProblem Receiver intermittently doesnrsquot receive the transmitter(s) signal
Solution You may extend the receiver antenna wire only in multiples of 6-34rdquo (171) ie 675 x 4 = 27rdquo (686) of extended antenna wire
Removing Transmitter Code(s)
Single Transmitter CodeŸ Press both Delay and No Delay Buttons simultaneously until Red LED flashes once (approximately 1 second)Ÿ Press transmitter button twice within 10 seconds and the transmitter code will be deleted
All Transmitter CodesŸ Press and hold both Delay and No Delay Buttons simultaneously until Blue LED illuminates then release (approximately 10
seconds)
Push Plate Configuration
1 Before beginning it is easiest to have already prepared the installation of the push plate2 Connect the wires from the transmitter to the NO and COM contacts of the push platersquos switch3 Follow Steps 1 - 4 (Hand-Held Configuration) depress the push plate to activate the transmitter4 Attach the transmitter to the inside of the electrical box and complete the installation
Hand-Held Configuration
1 Set dip switches to the receiver to the desired activation cycle (dip switch 1 - Toggle or Pulse and dip switch 2 - 05s or 10s hold
2 Press either Learn w Delay Button or Learn wo Delay Button on the receiver depending on the activation requirements (if delay learn is selected adjust potentiometer to counterclockwise limit 0 second delay) Red LED on receiver will flash After learn cycle is complete adjust potentiometer to desired delay time (0 - 30 sec)
3 Depress transmitter button repeatedly until Blue LED on the receiver illuminates (indicating reception of signal from transmitter) NOTE Repeat Steps 2 - 3 to program additional transmitters
4 To test the system depress transmitter button (Red LED on Transmitter will illuminate) and observe that the Blue LED illuminates on the receiver This indicates that the relay has been activated
433MHz Receiver Userrsquos Guide
2OFFON
Description05s Hold Time10s Hold Time
FunctionRelay will remain active 05 sec after loss of activationRelay will remain active 10 sec after loss of activation
1OFF
ON
DescriptionPulse Relay
Toggle Relay
FunctionPress the transmitter once and the relay will be active momentarilyPress the transmitter once and the relay output is active indefinitely press it again and the relay will de-energize indefinitely
ON
1 2PU
L T
OG
05s
1
0s ON
1 2PU
L T
OG
05s
1
0sIn Toggle Setting (1-ON) the Hold Time is inactive Either setting for 2 dip switch will
have the same result
ON
1 2PU
L T
OG
05s
1
0s
05 second Pulse Setting
ON
1 2PU
L T
OG
05s
1
0s
10 second Pulse Setting
ŸAlways stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door
ŸEnsure compliance with all applicable safety standards upon completion of installation
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
This PageLeft Blank
Page 13
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Hinge (Pull) SideŸ Do not scale drawingŸ Right hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
No
te D
oo
r m
ust
be
visi
ble
by
per
son
o
per
atin
g a
ctiv
atio
n s
wit
ch(e
s)
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Up
to 1
10deg
111deg
to 1
80deg
15-1
2 (
394)
13-1
4 (
337)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull T
hick
ness
rec
omm
ende
d fo
r re
info
rcem
ents
in h
ollo
w
met
al d
oors
and
fram
es is
cha
rted
on
Pag
e 2
bull D
o no
t sca
le d
raw
ing
bull R
ight
han
d do
or s
how
nbull
Thi
s te
mpl
ate
info
rmat
ion
base
d up
on u
se o
f 5
(127
mm
) m
axim
um w
idth
but
t hin
ges
A s
epar
ate
tem
plat
e is
req
uire
d fo
r ot
her
cond
ition
sbull
Max
imum
fram
e re
veal
is 6
-78
rdquo (17
5mm
) fo
r th
is
appl
icat
ion
bull C
ondu
it ho
le n
eare
st th
e hi
nge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
2rdquo (
51m
m)
Min
F
ram
e Fa
ce
1-1
8rdquo(2
9)
1-1
4(3
2)1-
716
(37)
11(2
79)
22(5
59)
7-9
16(1
92)
13-7
16
(341
)
1-1
8(2
9)
C LH
inge
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)7
8 (2
3) D
ia
(2 P
lace
s)
38
Dia
S
ex N
uts
(3 P
lace
s)
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
3(7
6)
13-1
316
(350
)
12
(13)
A
11-1
116
(297
)
6rdquo
(152
mm
)M
in
Cle
aran
ce
14-3
16
(360
)
12-1
516
(329
)13
-13
16(3
51)
Rig
ht
Han
d D
oo
ro
pen
ing
to
110
deg sh
ow
n
58
(15
9)S
top
Left
Han
dD
oor
Rig
htH
and
Doo
r
2rdquo (
51m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
6rdquo (
152m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
ax
Do
or T
hic
knes
s
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Hin
ge
(Pu
ll) S
ide
app
licat
ion
as
sho
wn
on
th
is
tem
pla
te
Page 14
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Stop (Push) SideŸ Do not scale drawingŸ Left hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Dim
ldquoB
rdquo
Up
to 1
10deg
111deg
to 1
70deg
12 (
305)
9-1
2 (2
41)
13-1
4 (
337)
15-3
4 (
400)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull Thi
ckne
ss r
ecom
men
ded
for
rein
forc
emen
ts in
ho
llow
met
al d
oors
and
fram
es is
cha
rted
at t
he
left
of th
is p
age
bull D
o no
t sca
le d
raw
ing
bull Le
ft ha
nd d
oor
show
nbull T
his
tem
plat
e in
form
atio
n ba
sed
upon
use
of 5
(1
27m
m)
max
imum
wid
th b
utt h
inge
s or
34
(1
9mm
) of
fset
piv
ots
A s
epar
ate
tem
plat
e w
ill
be s
uppl
ied
for
othe
r co
nditi
ons
bull M
axim
um fr
ame
reve
al is
7rdquo (
178m
m)
for
this
ap
plic
atio
nbull
Con
duit
hole
nea
rest
to h
inge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
1-11
16
(43)
1-1
4(3
2)11
16
(17
5)
1-3
4(4
4)
12-1
516
(329
)
7-9
16(1
92)
13-7
16
(341
)
38
(10)
C LH
inge
or
Piv
ot
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)
78
(22)
(Con
duit
Hol
es -
2
Pla
ces)
Dia
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
A13-1
316
(351
)
12
(13)
B
5-1
4rdquoM
in
Cle
aran
ce
11-1
116
(297
)
38
(19)
14-3
16
(360
)13
-13
16(3
51)
Lef
t H
and
Do
or
op
en t
o 1
10deg
sho
wn
58
(15
9)S
top
Sex
Nu
ts(2
Pla
ces)
Left
Han
dD
oor
Rig
htH
and
Doo
r
1-1
2rdquo (
38m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
5-1
4rdquo (
133m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
axD
oo
r Th
ickn
ess
No
te D
oo
r m
ust
be
visi
ble
by
per
son
op
erat
ing
act
ivat
ion
sw
itch
(es)
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Sto
p (
Pu
sh)
Sid
e ap
plic
atio
n a
s sh
ow
n o
n t
his
te
mp
late
Page 15
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
3000 Highway 74 East bull Monroe NC 28112Tel (800)-438-1951 x4706 bull Fax (800)-338-0965
wwwnor tondoorcontrolscom
ASSA ABLOY
This PageLeft Blank
Page 16
ASSA ABLOY
Low VoltageControlWiring
IncomingPower
Optional Bracket(for surface wiring)
GroundLead
PowerLeads
GroundScrew(Green)
CableClamps Conduit
by Others(from top)
ldquoT1rdquo PowerInputTerminal
24
23
22
25
HOT
COM
Breaker Switch
T1 TerminalBlock
4 Final Electrical and Mechanical SetupA Confirm all mechanical adjustments have been made
and wiring connected per Page 7 and 8B Turn on facilityrsquos main circuit breakerC Turn power to unit on at the Unit Power Switch and
turn the Breaker Switch to ldquoRESETrdquo
D Using a short jumper cable jump terminals 1 and 2 see Fig 2 below to activate unit When door reaches 20deg switch Breaker Switch to ldquoOFFrdquo position cutting power to the unit Allow door to fully close (door may be manually pulled closed)
1234
1234
Figure 2
3 Input Power ConfigurationsCONCEALED WIRING SURFACE WIRING
Ground Wire Connection ndash Ground wire must be secured to backplate under head of (green) ground screw
Terminal Description
HOT
25
23
24
22
COM Common power lead
Hot power lead
Circuit Breaker
Switch
Circuit Breaker
Common connection to Circuit Breaker Inverter
Thread conduit fitting(s) into backplate as shown A second conduit fitting is required for low voltage control wiring CHECK LOCAL CODES Pull conduit out of header and attach to conduit fittings before mounting Secure operator to door frame Attach incoming ground wire to backplate with ground screw as illustrated in ldquoSurface Wiringrdquo illustration to the Right
Thread conduit fitting(s) into backplate as shown A second conduit fitting is required for low voltage control wiring CHECK LOCAL CODES Pull conduit out of header and attach to conduit fittings before mounting Secure operator to door frame Attach incoming ground wire to backplate with ground screw as illustrated below
Breaker Switch
Unit Power Switch
Page 8
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
4 Final Electrical and Mechanical Setup ContinuedE Adjust Closing Position Magnet (See Fig 3) - With
door in the closed position use finger to slide Closed Position Magnet so it aligns directly with the Reed Switch
F Adjust Open Position Magnet - Use fingers to slide
F cont Open Position Magnet 180deg from Open Position Magnet
G Flip Breaker Switch to ldquoRESETrdquo to turn power on Jump terminals 1 and 2 (as shown in Fig 2) to activate door Note open position of the door Allow door to close
H Use finger to readjust the Open Position Magnet to desired door open position
I Repeat Step G to verify door open position J Make all connections necessary for any accessories to
the 4-position Accessory Terminal (see Pages 10-11)K Make necessary adjustments to inverter (see Page 9)
Replace cover and cover screws
Reed Switch
Closed Position Magnet
Open PositionMagnet
Position Ring
Figure 3
Inverter Adjustmentsmiddot Based on function
adjustment desired use table above to determine which POT is to be adjusted
POT FUNCTIONDESCRIPTION
OBSTR SENS Obstruction Detection on Open CW - IncreaseCCW - Decrease
MDLY Motor Delay on Opening CW - IncreaseCCW - Decrease
P1 Closing Speed CW - IncreaseCCW - Decrease
HO TM Hold Open Time (5 - 30 Seconds) CW - IncreaseCCW - Decrease
P2 Opening Speed CW - IncreaseCCW - Decrease
HO TQMotor Torque at Hold Open Position
CW - IncreaseCCW - Decrease
ON
12
WARNING
120 HIGH VOLT POTENTIAL PRESENT MAKE SURE POWER IS TURNED OFF DURING
INSTALLATION PROCEDURE
Dip Switch Settings
1 Door Mounting -
2 Push Recognition -
ON - pullOFF - pushON - activeOFF - inactive
WARNINGElectric
Shock Risk
(Adjustments made in the shaded area should be performed by
Authorized Factory Personnel)
L2115Y
L1 115230VAC IN
MOTOR OUT
L2230Y
U
V
W
STATUS LEDS
HO TQHO TM
OBSTRSENS
P1
MDLY P2
16
COM
SNS
COM
PB
K1
K2
11
JMP503
NC
NO
TB501
PU
LL P
US
HSW501
ON
12
Inverter Details
Page 9
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Standard Function with Switches
1
2
3
4
1
2
3
4
Notes1Power input to Door
Operator Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
Wall Switch CardReader Key Switchetc
1
2
3
4
1
2
3
4Door 1 Door 2
Operationbull bull Activating either switch will
open both doors Door will close after hold open time delay has elapsed
Doors are normally closed
Wall Switch CardReader Key Switchetc
Normally Open Momentary dry contacts
Normally Open Momentary dry contacts
Radio Frequency Function Option
1 2 3 4
1 2 3 4
Optional Door 2
1 2 3 4
1 2 3 4
Door 1
Notes1Power input to Door Operator
Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
2 Radio Frequency Feature can be purchased as a separate kit
Operationbull
closedbull Activating wireless
switch or hand held wireless transmitter will open the door
bull Door will close after hold open delay elapses
Door is normally
120VAC
GroundC
OM
HO
TL N(AC) -V +V ADJ
+
11A 24V Power Supply12-24 VA
CD
CC
OM
NO
NC
Troubleshooting
Jump activation input
Change the setting of the ONOFF switch
Flip Door Mounting Dip Switch to other direction
Remove object
Re-time and re-install arm
Increase spring tension per preceding instructions
Remove object
Fault Possible reasons why RemediesExplanations
The door does not open- The motor does not start
Control switch is set to OFF position
Electrical power is missing the electrical Check power switch
Activation unit does not function- The motor starts Motor is driving in wrong direction
Something jammed beneath the door
Arm has come loose
The door does not close Spring tension too lowArm has come loose Re-time and re-install arm
Something jammed beneath the door
Circuit breaker is set to OFF position Reset circuit breaker to the ON position
Page 10
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Fail Secure Fail Safe Electric Strike Wiring
120VACSupplied byOthers- +
DC or ACOutput
AC
or
DC
Ele
ctric
Str
ike+
-
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating for strike interface 30VDC 1A or 125VAC 5A
Operationbull bull Activating switch will unlock the electric strike
and the door will automatically open Door will close after hold open time delay has elapsed
bull For Fail Secure Strike - The door will remain locked during power failure
bull For Fail Safe Strike - The door will remain unlocked during power failure
Door is normally closed and latched
1
2
3
4
1
2
3
4
JMP503
NC
NO
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
Fail Safe Electromagnetic Lock 24VDC Wiring
1
2
3
4
1
2
3
4
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
+-24VDC Electromagnetic Lock(Fail Safe)
Operationbull bull Activating switch will cut power to mag lock and the door will automatically
open Door will close after hold open time delay has elapsedbull The door will unlock during power failure
Door is normally closed and latched
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating 30VDC 1A or 125VAC 5A
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
JMP503
NC
NO
120VAC
GroundC
OM
HO
T
L N(AC) -V +V ADJ+
Optional 11A 24V Power Supply
Page 11
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Page 12
Troubleshooting
Red LEDBlue LED
Antenna Wire
Learnwo DelayButton
DelayPotentiometer(Time Adjustment)
Learn wDelay Button
DIP Switch
TerminalStrip
Problem The LED on my receiver is just flickering and Irsquom unable to program andor it wonrsquot workSolution You have a push plate stuck or faulty transmitter Disconnect each push plate until the LED goes out If LED
does not go out remove each transmitter battery until it does Replace the appropriate transmitterProblem Receiver intermittently doesnrsquot receive the transmitter(s) signal
Solution You may extend the receiver antenna wire only in multiples of 6-34rdquo (171) ie 675 x 4 = 27rdquo (686) of extended antenna wire
Removing Transmitter Code(s)
Single Transmitter CodeŸ Press both Delay and No Delay Buttons simultaneously until Red LED flashes once (approximately 1 second)Ÿ Press transmitter button twice within 10 seconds and the transmitter code will be deleted
All Transmitter CodesŸ Press and hold both Delay and No Delay Buttons simultaneously until Blue LED illuminates then release (approximately 10
seconds)
Push Plate Configuration
1 Before beginning it is easiest to have already prepared the installation of the push plate2 Connect the wires from the transmitter to the NO and COM contacts of the push platersquos switch3 Follow Steps 1 - 4 (Hand-Held Configuration) depress the push plate to activate the transmitter4 Attach the transmitter to the inside of the electrical box and complete the installation
Hand-Held Configuration
1 Set dip switches to the receiver to the desired activation cycle (dip switch 1 - Toggle or Pulse and dip switch 2 - 05s or 10s hold
2 Press either Learn w Delay Button or Learn wo Delay Button on the receiver depending on the activation requirements (if delay learn is selected adjust potentiometer to counterclockwise limit 0 second delay) Red LED on receiver will flash After learn cycle is complete adjust potentiometer to desired delay time (0 - 30 sec)
3 Depress transmitter button repeatedly until Blue LED on the receiver illuminates (indicating reception of signal from transmitter) NOTE Repeat Steps 2 - 3 to program additional transmitters
4 To test the system depress transmitter button (Red LED on Transmitter will illuminate) and observe that the Blue LED illuminates on the receiver This indicates that the relay has been activated
433MHz Receiver Userrsquos Guide
2OFFON
Description05s Hold Time10s Hold Time
FunctionRelay will remain active 05 sec after loss of activationRelay will remain active 10 sec after loss of activation
1OFF
ON
DescriptionPulse Relay
Toggle Relay
FunctionPress the transmitter once and the relay will be active momentarilyPress the transmitter once and the relay output is active indefinitely press it again and the relay will de-energize indefinitely
ON
1 2PU
L T
OG
05s
1
0s ON
1 2PU
L T
OG
05s
1
0sIn Toggle Setting (1-ON) the Hold Time is inactive Either setting for 2 dip switch will
have the same result
ON
1 2PU
L T
OG
05s
1
0s
05 second Pulse Setting
ON
1 2PU
L T
OG
05s
1
0s
10 second Pulse Setting
ŸAlways stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door
ŸEnsure compliance with all applicable safety standards upon completion of installation
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
This PageLeft Blank
Page 13
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Hinge (Pull) SideŸ Do not scale drawingŸ Right hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
No
te D
oo
r m
ust
be
visi
ble
by
per
son
o
per
atin
g a
ctiv
atio
n s
wit
ch(e
s)
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Up
to 1
10deg
111deg
to 1
80deg
15-1
2 (
394)
13-1
4 (
337)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull T
hick
ness
rec
omm
ende
d fo
r re
info
rcem
ents
in h
ollo
w
met
al d
oors
and
fram
es is
cha
rted
on
Pag
e 2
bull D
o no
t sca
le d
raw
ing
bull R
ight
han
d do
or s
how
nbull
Thi
s te
mpl
ate
info
rmat
ion
base
d up
on u
se o
f 5
(127
mm
) m
axim
um w
idth
but
t hin
ges
A s
epar
ate
tem
plat
e is
req
uire
d fo
r ot
her
cond
ition
sbull
Max
imum
fram
e re
veal
is 6
-78
rdquo (17
5mm
) fo
r th
is
appl
icat
ion
bull C
ondu
it ho
le n
eare
st th
e hi
nge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
2rdquo (
51m
m)
Min
F
ram
e Fa
ce
1-1
8rdquo(2
9)
1-1
4(3
2)1-
716
(37)
11(2
79)
22(5
59)
7-9
16(1
92)
13-7
16
(341
)
1-1
8(2
9)
C LH
inge
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)7
8 (2
3) D
ia
(2 P
lace
s)
38
Dia
S
ex N
uts
(3 P
lace
s)
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
3(7
6)
13-1
316
(350
)
12
(13)
A
11-1
116
(297
)
6rdquo
(152
mm
)M
in
Cle
aran
ce
14-3
16
(360
)
12-1
516
(329
)13
-13
16(3
51)
Rig
ht
Han
d D
oo
ro
pen
ing
to
110
deg sh
ow
n
58
(15
9)S
top
Left
Han
dD
oor
Rig
htH
and
Doo
r
2rdquo (
51m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
6rdquo (
152m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
ax
Do
or T
hic
knes
s
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Hin
ge
(Pu
ll) S
ide
app
licat
ion
as
sho
wn
on
th
is
tem
pla
te
Page 14
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Stop (Push) SideŸ Do not scale drawingŸ Left hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Dim
ldquoB
rdquo
Up
to 1
10deg
111deg
to 1
70deg
12 (
305)
9-1
2 (2
41)
13-1
4 (
337)
15-3
4 (
400)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull Thi
ckne
ss r
ecom
men
ded
for
rein
forc
emen
ts in
ho
llow
met
al d
oors
and
fram
es is
cha
rted
at t
he
left
of th
is p
age
bull D
o no
t sca
le d
raw
ing
bull Le
ft ha
nd d
oor
show
nbull T
his
tem
plat
e in
form
atio
n ba
sed
upon
use
of 5
(1
27m
m)
max
imum
wid
th b
utt h
inge
s or
34
(1
9mm
) of
fset
piv
ots
A s
epar
ate
tem
plat
e w
ill
be s
uppl
ied
for
othe
r co
nditi
ons
bull M
axim
um fr
ame
reve
al is
7rdquo (
178m
m)
for
this
ap
plic
atio
nbull
Con
duit
hole
nea
rest
to h
inge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
1-11
16
(43)
1-1
4(3
2)11
16
(17
5)
1-3
4(4
4)
12-1
516
(329
)
7-9
16(1
92)
13-7
16
(341
)
38
(10)
C LH
inge
or
Piv
ot
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)
78
(22)
(Con
duit
Hol
es -
2
Pla
ces)
Dia
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
A13-1
316
(351
)
12
(13)
B
5-1
4rdquoM
in
Cle
aran
ce
11-1
116
(297
)
38
(19)
14-3
16
(360
)13
-13
16(3
51)
Lef
t H
and
Do
or
op
en t
o 1
10deg
sho
wn
58
(15
9)S
top
Sex
Nu
ts(2
Pla
ces)
Left
Han
dD
oor
Rig
htH
and
Doo
r
1-1
2rdquo (
38m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
5-1
4rdquo (
133m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
axD
oo
r Th
ickn
ess
No
te D
oo
r m
ust
be
visi
ble
by
per
son
op
erat
ing
act
ivat
ion
sw
itch
(es)
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Sto
p (
Pu
sh)
Sid
e ap
plic
atio
n a
s sh
ow
n o
n t
his
te
mp
late
Page 15
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
3000 Highway 74 East bull Monroe NC 28112Tel (800)-438-1951 x4706 bull Fax (800)-338-0965
wwwnor tondoorcontrolscom
ASSA ABLOY
This PageLeft Blank
Page 16
ASSA ABLOY
4 Final Electrical and Mechanical Setup ContinuedE Adjust Closing Position Magnet (See Fig 3) - With
door in the closed position use finger to slide Closed Position Magnet so it aligns directly with the Reed Switch
F Adjust Open Position Magnet - Use fingers to slide
F cont Open Position Magnet 180deg from Open Position Magnet
G Flip Breaker Switch to ldquoRESETrdquo to turn power on Jump terminals 1 and 2 (as shown in Fig 2) to activate door Note open position of the door Allow door to close
H Use finger to readjust the Open Position Magnet to desired door open position
I Repeat Step G to verify door open position J Make all connections necessary for any accessories to
the 4-position Accessory Terminal (see Pages 10-11)K Make necessary adjustments to inverter (see Page 9)
Replace cover and cover screws
Reed Switch
Closed Position Magnet
Open PositionMagnet
Position Ring
Figure 3
Inverter Adjustmentsmiddot Based on function
adjustment desired use table above to determine which POT is to be adjusted
POT FUNCTIONDESCRIPTION
OBSTR SENS Obstruction Detection on Open CW - IncreaseCCW - Decrease
MDLY Motor Delay on Opening CW - IncreaseCCW - Decrease
P1 Closing Speed CW - IncreaseCCW - Decrease
HO TM Hold Open Time (5 - 30 Seconds) CW - IncreaseCCW - Decrease
P2 Opening Speed CW - IncreaseCCW - Decrease
HO TQMotor Torque at Hold Open Position
CW - IncreaseCCW - Decrease
ON
12
WARNING
120 HIGH VOLT POTENTIAL PRESENT MAKE SURE POWER IS TURNED OFF DURING
INSTALLATION PROCEDURE
Dip Switch Settings
1 Door Mounting -
2 Push Recognition -
ON - pullOFF - pushON - activeOFF - inactive
WARNINGElectric
Shock Risk
(Adjustments made in the shaded area should be performed by
Authorized Factory Personnel)
L2115Y
L1 115230VAC IN
MOTOR OUT
L2230Y
U
V
W
STATUS LEDS
HO TQHO TM
OBSTRSENS
P1
MDLY P2
16
COM
SNS
COM
PB
K1
K2
11
JMP503
NC
NO
TB501
PU
LL P
US
HSW501
ON
12
Inverter Details
Page 9
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Standard Function with Switches
1
2
3
4
1
2
3
4
Notes1Power input to Door
Operator Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
Wall Switch CardReader Key Switchetc
1
2
3
4
1
2
3
4Door 1 Door 2
Operationbull bull Activating either switch will
open both doors Door will close after hold open time delay has elapsed
Doors are normally closed
Wall Switch CardReader Key Switchetc
Normally Open Momentary dry contacts
Normally Open Momentary dry contacts
Radio Frequency Function Option
1 2 3 4
1 2 3 4
Optional Door 2
1 2 3 4
1 2 3 4
Door 1
Notes1Power input to Door Operator
Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
2 Radio Frequency Feature can be purchased as a separate kit
Operationbull
closedbull Activating wireless
switch or hand held wireless transmitter will open the door
bull Door will close after hold open delay elapses
Door is normally
120VAC
GroundC
OM
HO
TL N(AC) -V +V ADJ
+
11A 24V Power Supply12-24 VA
CD
CC
OM
NO
NC
Troubleshooting
Jump activation input
Change the setting of the ONOFF switch
Flip Door Mounting Dip Switch to other direction
Remove object
Re-time and re-install arm
Increase spring tension per preceding instructions
Remove object
Fault Possible reasons why RemediesExplanations
The door does not open- The motor does not start
Control switch is set to OFF position
Electrical power is missing the electrical Check power switch
Activation unit does not function- The motor starts Motor is driving in wrong direction
Something jammed beneath the door
Arm has come loose
The door does not close Spring tension too lowArm has come loose Re-time and re-install arm
Something jammed beneath the door
Circuit breaker is set to OFF position Reset circuit breaker to the ON position
Page 10
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Fail Secure Fail Safe Electric Strike Wiring
120VACSupplied byOthers- +
DC or ACOutput
AC
or
DC
Ele
ctric
Str
ike+
-
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating for strike interface 30VDC 1A or 125VAC 5A
Operationbull bull Activating switch will unlock the electric strike
and the door will automatically open Door will close after hold open time delay has elapsed
bull For Fail Secure Strike - The door will remain locked during power failure
bull For Fail Safe Strike - The door will remain unlocked during power failure
Door is normally closed and latched
1
2
3
4
1
2
3
4
JMP503
NC
NO
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
Fail Safe Electromagnetic Lock 24VDC Wiring
1
2
3
4
1
2
3
4
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
+-24VDC Electromagnetic Lock(Fail Safe)
Operationbull bull Activating switch will cut power to mag lock and the door will automatically
open Door will close after hold open time delay has elapsedbull The door will unlock during power failure
Door is normally closed and latched
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating 30VDC 1A or 125VAC 5A
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
JMP503
NC
NO
120VAC
GroundC
OM
HO
T
L N(AC) -V +V ADJ+
Optional 11A 24V Power Supply
Page 11
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Page 12
Troubleshooting
Red LEDBlue LED
Antenna Wire
Learnwo DelayButton
DelayPotentiometer(Time Adjustment)
Learn wDelay Button
DIP Switch
TerminalStrip
Problem The LED on my receiver is just flickering and Irsquom unable to program andor it wonrsquot workSolution You have a push plate stuck or faulty transmitter Disconnect each push plate until the LED goes out If LED
does not go out remove each transmitter battery until it does Replace the appropriate transmitterProblem Receiver intermittently doesnrsquot receive the transmitter(s) signal
Solution You may extend the receiver antenna wire only in multiples of 6-34rdquo (171) ie 675 x 4 = 27rdquo (686) of extended antenna wire
Removing Transmitter Code(s)
Single Transmitter CodeŸ Press both Delay and No Delay Buttons simultaneously until Red LED flashes once (approximately 1 second)Ÿ Press transmitter button twice within 10 seconds and the transmitter code will be deleted
All Transmitter CodesŸ Press and hold both Delay and No Delay Buttons simultaneously until Blue LED illuminates then release (approximately 10
seconds)
Push Plate Configuration
1 Before beginning it is easiest to have already prepared the installation of the push plate2 Connect the wires from the transmitter to the NO and COM contacts of the push platersquos switch3 Follow Steps 1 - 4 (Hand-Held Configuration) depress the push plate to activate the transmitter4 Attach the transmitter to the inside of the electrical box and complete the installation
Hand-Held Configuration
1 Set dip switches to the receiver to the desired activation cycle (dip switch 1 - Toggle or Pulse and dip switch 2 - 05s or 10s hold
2 Press either Learn w Delay Button or Learn wo Delay Button on the receiver depending on the activation requirements (if delay learn is selected adjust potentiometer to counterclockwise limit 0 second delay) Red LED on receiver will flash After learn cycle is complete adjust potentiometer to desired delay time (0 - 30 sec)
3 Depress transmitter button repeatedly until Blue LED on the receiver illuminates (indicating reception of signal from transmitter) NOTE Repeat Steps 2 - 3 to program additional transmitters
4 To test the system depress transmitter button (Red LED on Transmitter will illuminate) and observe that the Blue LED illuminates on the receiver This indicates that the relay has been activated
433MHz Receiver Userrsquos Guide
2OFFON
Description05s Hold Time10s Hold Time
FunctionRelay will remain active 05 sec after loss of activationRelay will remain active 10 sec after loss of activation
1OFF
ON
DescriptionPulse Relay
Toggle Relay
FunctionPress the transmitter once and the relay will be active momentarilyPress the transmitter once and the relay output is active indefinitely press it again and the relay will de-energize indefinitely
ON
1 2PU
L T
OG
05s
1
0s ON
1 2PU
L T
OG
05s
1
0sIn Toggle Setting (1-ON) the Hold Time is inactive Either setting for 2 dip switch will
have the same result
ON
1 2PU
L T
OG
05s
1
0s
05 second Pulse Setting
ON
1 2PU
L T
OG
05s
1
0s
10 second Pulse Setting
ŸAlways stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door
ŸEnsure compliance with all applicable safety standards upon completion of installation
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
This PageLeft Blank
Page 13
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Hinge (Pull) SideŸ Do not scale drawingŸ Right hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
No
te D
oo
r m
ust
be
visi
ble
by
per
son
o
per
atin
g a
ctiv
atio
n s
wit
ch(e
s)
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Up
to 1
10deg
111deg
to 1
80deg
15-1
2 (
394)
13-1
4 (
337)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull T
hick
ness
rec
omm
ende
d fo
r re
info
rcem
ents
in h
ollo
w
met
al d
oors
and
fram
es is
cha
rted
on
Pag
e 2
bull D
o no
t sca
le d
raw
ing
bull R
ight
han
d do
or s
how
nbull
Thi
s te
mpl
ate
info
rmat
ion
base
d up
on u
se o
f 5
(127
mm
) m
axim
um w
idth
but
t hin
ges
A s
epar
ate
tem
plat
e is
req
uire
d fo
r ot
her
cond
ition
sbull
Max
imum
fram
e re
veal
is 6
-78
rdquo (17
5mm
) fo
r th
is
appl
icat
ion
bull C
ondu
it ho
le n
eare
st th
e hi
nge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
2rdquo (
51m
m)
Min
F
ram
e Fa
ce
1-1
8rdquo(2
9)
1-1
4(3
2)1-
716
(37)
11(2
79)
22(5
59)
7-9
16(1
92)
13-7
16
(341
)
1-1
8(2
9)
C LH
inge
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)7
8 (2
3) D
ia
(2 P
lace
s)
38
Dia
S
ex N
uts
(3 P
lace
s)
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
3(7
6)
13-1
316
(350
)
12
(13)
A
11-1
116
(297
)
6rdquo
(152
mm
)M
in
Cle
aran
ce
14-3
16
(360
)
12-1
516
(329
)13
-13
16(3
51)
Rig
ht
Han
d D
oo
ro
pen
ing
to
110
deg sh
ow
n
58
(15
9)S
top
Left
Han
dD
oor
Rig
htH
and
Doo
r
2rdquo (
51m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
6rdquo (
152m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
ax
Do
or T
hic
knes
s
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Hin
ge
(Pu
ll) S
ide
app
licat
ion
as
sho
wn
on
th
is
tem
pla
te
Page 14
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Stop (Push) SideŸ Do not scale drawingŸ Left hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Dim
ldquoB
rdquo
Up
to 1
10deg
111deg
to 1
70deg
12 (
305)
9-1
2 (2
41)
13-1
4 (
337)
15-3
4 (
400)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull Thi
ckne
ss r
ecom
men
ded
for
rein
forc
emen
ts in
ho
llow
met
al d
oors
and
fram
es is
cha
rted
at t
he
left
of th
is p
age
bull D
o no
t sca
le d
raw
ing
bull Le
ft ha
nd d
oor
show
nbull T
his
tem
plat
e in
form
atio
n ba
sed
upon
use
of 5
(1
27m
m)
max
imum
wid
th b
utt h
inge
s or
34
(1
9mm
) of
fset
piv
ots
A s
epar
ate
tem
plat
e w
ill
be s
uppl
ied
for
othe
r co
nditi
ons
bull M
axim
um fr
ame
reve
al is
7rdquo (
178m
m)
for
this
ap
plic
atio
nbull
Con
duit
hole
nea
rest
to h
inge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
1-11
16
(43)
1-1
4(3
2)11
16
(17
5)
1-3
4(4
4)
12-1
516
(329
)
7-9
16(1
92)
13-7
16
(341
)
38
(10)
C LH
inge
or
Piv
ot
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)
78
(22)
(Con
duit
Hol
es -
2
Pla
ces)
Dia
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
A13-1
316
(351
)
12
(13)
B
5-1
4rdquoM
in
Cle
aran
ce
11-1
116
(297
)
38
(19)
14-3
16
(360
)13
-13
16(3
51)
Lef
t H
and
Do
or
op
en t
o 1
10deg
sho
wn
58
(15
9)S
top
Sex
Nu
ts(2
Pla
ces)
Left
Han
dD
oor
Rig
htH
and
Doo
r
1-1
2rdquo (
38m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
5-1
4rdquo (
133m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
axD
oo
r Th
ickn
ess
No
te D
oo
r m
ust
be
visi
ble
by
per
son
op
erat
ing
act
ivat
ion
sw
itch
(es)
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Sto
p (
Pu
sh)
Sid
e ap
plic
atio
n a
s sh
ow
n o
n t
his
te
mp
late
Page 15
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
3000 Highway 74 East bull Monroe NC 28112Tel (800)-438-1951 x4706 bull Fax (800)-338-0965
wwwnor tondoorcontrolscom
ASSA ABLOY
This PageLeft Blank
Page 16
ASSA ABLOY
Standard Function with Switches
1
2
3
4
1
2
3
4
Notes1Power input to Door
Operator Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
Wall Switch CardReader Key Switchetc
1
2
3
4
1
2
3
4Door 1 Door 2
Operationbull bull Activating either switch will
open both doors Door will close after hold open time delay has elapsed
Doors are normally closed
Wall Switch CardReader Key Switchetc
Normally Open Momentary dry contacts
Normally Open Momentary dry contacts
Radio Frequency Function Option
1 2 3 4
1 2 3 4
Optional Door 2
1 2 3 4
1 2 3 4
Door 1
Notes1Power input to Door Operator
Unit is at ldquoT1rdquo Power Input Terminal (not shown) 120VAC 60Hz
2 Radio Frequency Feature can be purchased as a separate kit
Operationbull
closedbull Activating wireless
switch or hand held wireless transmitter will open the door
bull Door will close after hold open delay elapses
Door is normally
120VAC
GroundC
OM
HO
TL N(AC) -V +V ADJ
+
11A 24V Power Supply12-24 VA
CD
CC
OM
NO
NC
Troubleshooting
Jump activation input
Change the setting of the ONOFF switch
Flip Door Mounting Dip Switch to other direction
Remove object
Re-time and re-install arm
Increase spring tension per preceding instructions
Remove object
Fault Possible reasons why RemediesExplanations
The door does not open- The motor does not start
Control switch is set to OFF position
Electrical power is missing the electrical Check power switch
Activation unit does not function- The motor starts Motor is driving in wrong direction
Something jammed beneath the door
Arm has come loose
The door does not close Spring tension too lowArm has come loose Re-time and re-install arm
Something jammed beneath the door
Circuit breaker is set to OFF position Reset circuit breaker to the ON position
Page 10
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Fail Secure Fail Safe Electric Strike Wiring
120VACSupplied byOthers- +
DC or ACOutput
AC
or
DC
Ele
ctric
Str
ike+
-
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating for strike interface 30VDC 1A or 125VAC 5A
Operationbull bull Activating switch will unlock the electric strike
and the door will automatically open Door will close after hold open time delay has elapsed
bull For Fail Secure Strike - The door will remain locked during power failure
bull For Fail Safe Strike - The door will remain unlocked during power failure
Door is normally closed and latched
1
2
3
4
1
2
3
4
JMP503
NC
NO
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
Fail Safe Electromagnetic Lock 24VDC Wiring
1
2
3
4
1
2
3
4
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
+-24VDC Electromagnetic Lock(Fail Safe)
Operationbull bull Activating switch will cut power to mag lock and the door will automatically
open Door will close after hold open time delay has elapsedbull The door will unlock during power failure
Door is normally closed and latched
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating 30VDC 1A or 125VAC 5A
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
JMP503
NC
NO
120VAC
GroundC
OM
HO
T
L N(AC) -V +V ADJ+
Optional 11A 24V Power Supply
Page 11
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Page 12
Troubleshooting
Red LEDBlue LED
Antenna Wire
Learnwo DelayButton
DelayPotentiometer(Time Adjustment)
Learn wDelay Button
DIP Switch
TerminalStrip
Problem The LED on my receiver is just flickering and Irsquom unable to program andor it wonrsquot workSolution You have a push plate stuck or faulty transmitter Disconnect each push plate until the LED goes out If LED
does not go out remove each transmitter battery until it does Replace the appropriate transmitterProblem Receiver intermittently doesnrsquot receive the transmitter(s) signal
Solution You may extend the receiver antenna wire only in multiples of 6-34rdquo (171) ie 675 x 4 = 27rdquo (686) of extended antenna wire
Removing Transmitter Code(s)
Single Transmitter CodeŸ Press both Delay and No Delay Buttons simultaneously until Red LED flashes once (approximately 1 second)Ÿ Press transmitter button twice within 10 seconds and the transmitter code will be deleted
All Transmitter CodesŸ Press and hold both Delay and No Delay Buttons simultaneously until Blue LED illuminates then release (approximately 10
seconds)
Push Plate Configuration
1 Before beginning it is easiest to have already prepared the installation of the push plate2 Connect the wires from the transmitter to the NO and COM contacts of the push platersquos switch3 Follow Steps 1 - 4 (Hand-Held Configuration) depress the push plate to activate the transmitter4 Attach the transmitter to the inside of the electrical box and complete the installation
Hand-Held Configuration
1 Set dip switches to the receiver to the desired activation cycle (dip switch 1 - Toggle or Pulse and dip switch 2 - 05s or 10s hold
2 Press either Learn w Delay Button or Learn wo Delay Button on the receiver depending on the activation requirements (if delay learn is selected adjust potentiometer to counterclockwise limit 0 second delay) Red LED on receiver will flash After learn cycle is complete adjust potentiometer to desired delay time (0 - 30 sec)
3 Depress transmitter button repeatedly until Blue LED on the receiver illuminates (indicating reception of signal from transmitter) NOTE Repeat Steps 2 - 3 to program additional transmitters
4 To test the system depress transmitter button (Red LED on Transmitter will illuminate) and observe that the Blue LED illuminates on the receiver This indicates that the relay has been activated
433MHz Receiver Userrsquos Guide
2OFFON
Description05s Hold Time10s Hold Time
FunctionRelay will remain active 05 sec after loss of activationRelay will remain active 10 sec after loss of activation
1OFF
ON
DescriptionPulse Relay
Toggle Relay
FunctionPress the transmitter once and the relay will be active momentarilyPress the transmitter once and the relay output is active indefinitely press it again and the relay will de-energize indefinitely
ON
1 2PU
L T
OG
05s
1
0s ON
1 2PU
L T
OG
05s
1
0sIn Toggle Setting (1-ON) the Hold Time is inactive Either setting for 2 dip switch will
have the same result
ON
1 2PU
L T
OG
05s
1
0s
05 second Pulse Setting
ON
1 2PU
L T
OG
05s
1
0s
10 second Pulse Setting
ŸAlways stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door
ŸEnsure compliance with all applicable safety standards upon completion of installation
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
This PageLeft Blank
Page 13
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Hinge (Pull) SideŸ Do not scale drawingŸ Right hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
No
te D
oo
r m
ust
be
visi
ble
by
per
son
o
per
atin
g a
ctiv
atio
n s
wit
ch(e
s)
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Up
to 1
10deg
111deg
to 1
80deg
15-1
2 (
394)
13-1
4 (
337)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull T
hick
ness
rec
omm
ende
d fo
r re
info
rcem
ents
in h
ollo
w
met
al d
oors
and
fram
es is
cha
rted
on
Pag
e 2
bull D
o no
t sca
le d
raw
ing
bull R
ight
han
d do
or s
how
nbull
Thi
s te
mpl
ate
info
rmat
ion
base
d up
on u
se o
f 5
(127
mm
) m
axim
um w
idth
but
t hin
ges
A s
epar
ate
tem
plat
e is
req
uire
d fo
r ot
her
cond
ition
sbull
Max
imum
fram
e re
veal
is 6
-78
rdquo (17
5mm
) fo
r th
is
appl
icat
ion
bull C
ondu
it ho
le n
eare
st th
e hi
nge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
2rdquo (
51m
m)
Min
F
ram
e Fa
ce
1-1
8rdquo(2
9)
1-1
4(3
2)1-
716
(37)
11(2
79)
22(5
59)
7-9
16(1
92)
13-7
16
(341
)
1-1
8(2
9)
C LH
inge
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)7
8 (2
3) D
ia
(2 P
lace
s)
38
Dia
S
ex N
uts
(3 P
lace
s)
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
3(7
6)
13-1
316
(350
)
12
(13)
A
11-1
116
(297
)
6rdquo
(152
mm
)M
in
Cle
aran
ce
14-3
16
(360
)
12-1
516
(329
)13
-13
16(3
51)
Rig
ht
Han
d D
oo
ro
pen
ing
to
110
deg sh
ow
n
58
(15
9)S
top
Left
Han
dD
oor
Rig
htH
and
Doo
r
2rdquo (
51m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
6rdquo (
152m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
ax
Do
or T
hic
knes
s
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Hin
ge
(Pu
ll) S
ide
app
licat
ion
as
sho
wn
on
th
is
tem
pla
te
Page 14
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Stop (Push) SideŸ Do not scale drawingŸ Left hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Dim
ldquoB
rdquo
Up
to 1
10deg
111deg
to 1
70deg
12 (
305)
9-1
2 (2
41)
13-1
4 (
337)
15-3
4 (
400)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull Thi
ckne
ss r
ecom
men
ded
for
rein
forc
emen
ts in
ho
llow
met
al d
oors
and
fram
es is
cha
rted
at t
he
left
of th
is p
age
bull D
o no
t sca
le d
raw
ing
bull Le
ft ha
nd d
oor
show
nbull T
his
tem
plat
e in
form
atio
n ba
sed
upon
use
of 5
(1
27m
m)
max
imum
wid
th b
utt h
inge
s or
34
(1
9mm
) of
fset
piv
ots
A s
epar
ate
tem
plat
e w
ill
be s
uppl
ied
for
othe
r co
nditi
ons
bull M
axim
um fr
ame
reve
al is
7rdquo (
178m
m)
for
this
ap
plic
atio
nbull
Con
duit
hole
nea
rest
to h
inge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
1-11
16
(43)
1-1
4(3
2)11
16
(17
5)
1-3
4(4
4)
12-1
516
(329
)
7-9
16(1
92)
13-7
16
(341
)
38
(10)
C LH
inge
or
Piv
ot
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)
78
(22)
(Con
duit
Hol
es -
2
Pla
ces)
Dia
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
A13-1
316
(351
)
12
(13)
B
5-1
4rdquoM
in
Cle
aran
ce
11-1
116
(297
)
38
(19)
14-3
16
(360
)13
-13
16(3
51)
Lef
t H
and
Do
or
op
en t
o 1
10deg
sho
wn
58
(15
9)S
top
Sex
Nu
ts(2
Pla
ces)
Left
Han
dD
oor
Rig
htH
and
Doo
r
1-1
2rdquo (
38m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
5-1
4rdquo (
133m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
axD
oo
r Th
ickn
ess
No
te D
oo
r m
ust
be
visi
ble
by
per
son
op
erat
ing
act
ivat
ion
sw
itch
(es)
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Sto
p (
Pu
sh)
Sid
e ap
plic
atio
n a
s sh
ow
n o
n t
his
te
mp
late
Page 15
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
3000 Highway 74 East bull Monroe NC 28112Tel (800)-438-1951 x4706 bull Fax (800)-338-0965
wwwnor tondoorcontrolscom
ASSA ABLOY
This PageLeft Blank
Page 16
ASSA ABLOY
Fail Secure Fail Safe Electric Strike Wiring
120VACSupplied byOthers- +
DC or ACOutput
AC
or
DC
Ele
ctric
Str
ike+
-
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating for strike interface 30VDC 1A or 125VAC 5A
Operationbull bull Activating switch will unlock the electric strike
and the door will automatically open Door will close after hold open time delay has elapsed
bull For Fail Secure Strike - The door will remain locked during power failure
bull For Fail Safe Strike - The door will remain unlocked during power failure
Door is normally closed and latched
1
2
3
4
1
2
3
4
JMP503
NC
NO
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
Fail Safe Electromagnetic Lock 24VDC Wiring
1
2
3
4
1
2
3
4
Wall Switch CardReader Key SwitchetcNormally Open Momentary dry contacts
+-24VDC Electromagnetic Lock(Fail Safe)
Operationbull bull Activating switch will cut power to mag lock and the door will automatically
open Door will close after hold open time delay has elapsedbull The door will unlock during power failure
Door is normally closed and latched
Notes1Power input to Door Operator Unit is at ldquoT1rdquo
Power Input Terminal (not shown) 120VAC 60Hz
2Unitrsquos Relay Rating 30VDC 1A or 125VAC 5A
Jumper SettingsPlace jumper to upper position for normally closed operation or to lower position for normally open operation
JMP503
NC
NO
120VAC
GroundC
OM
HO
T
L N(AC) -V +V ADJ+
Optional 11A 24V Power Supply
Page 11
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Page 12
Troubleshooting
Red LEDBlue LED
Antenna Wire
Learnwo DelayButton
DelayPotentiometer(Time Adjustment)
Learn wDelay Button
DIP Switch
TerminalStrip
Problem The LED on my receiver is just flickering and Irsquom unable to program andor it wonrsquot workSolution You have a push plate stuck or faulty transmitter Disconnect each push plate until the LED goes out If LED
does not go out remove each transmitter battery until it does Replace the appropriate transmitterProblem Receiver intermittently doesnrsquot receive the transmitter(s) signal
Solution You may extend the receiver antenna wire only in multiples of 6-34rdquo (171) ie 675 x 4 = 27rdquo (686) of extended antenna wire
Removing Transmitter Code(s)
Single Transmitter CodeŸ Press both Delay and No Delay Buttons simultaneously until Red LED flashes once (approximately 1 second)Ÿ Press transmitter button twice within 10 seconds and the transmitter code will be deleted
All Transmitter CodesŸ Press and hold both Delay and No Delay Buttons simultaneously until Blue LED illuminates then release (approximately 10
seconds)
Push Plate Configuration
1 Before beginning it is easiest to have already prepared the installation of the push plate2 Connect the wires from the transmitter to the NO and COM contacts of the push platersquos switch3 Follow Steps 1 - 4 (Hand-Held Configuration) depress the push plate to activate the transmitter4 Attach the transmitter to the inside of the electrical box and complete the installation
Hand-Held Configuration
1 Set dip switches to the receiver to the desired activation cycle (dip switch 1 - Toggle or Pulse and dip switch 2 - 05s or 10s hold
2 Press either Learn w Delay Button or Learn wo Delay Button on the receiver depending on the activation requirements (if delay learn is selected adjust potentiometer to counterclockwise limit 0 second delay) Red LED on receiver will flash After learn cycle is complete adjust potentiometer to desired delay time (0 - 30 sec)
3 Depress transmitter button repeatedly until Blue LED on the receiver illuminates (indicating reception of signal from transmitter) NOTE Repeat Steps 2 - 3 to program additional transmitters
4 To test the system depress transmitter button (Red LED on Transmitter will illuminate) and observe that the Blue LED illuminates on the receiver This indicates that the relay has been activated
433MHz Receiver Userrsquos Guide
2OFFON
Description05s Hold Time10s Hold Time
FunctionRelay will remain active 05 sec after loss of activationRelay will remain active 10 sec after loss of activation
1OFF
ON
DescriptionPulse Relay
Toggle Relay
FunctionPress the transmitter once and the relay will be active momentarilyPress the transmitter once and the relay output is active indefinitely press it again and the relay will de-energize indefinitely
ON
1 2PU
L T
OG
05s
1
0s ON
1 2PU
L T
OG
05s
1
0sIn Toggle Setting (1-ON) the Hold Time is inactive Either setting for 2 dip switch will
have the same result
ON
1 2PU
L T
OG
05s
1
0s
05 second Pulse Setting
ON
1 2PU
L T
OG
05s
1
0s
10 second Pulse Setting
ŸAlways stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door
ŸEnsure compliance with all applicable safety standards upon completion of installation
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
This PageLeft Blank
Page 13
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Hinge (Pull) SideŸ Do not scale drawingŸ Right hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
No
te D
oo
r m
ust
be
visi
ble
by
per
son
o
per
atin
g a
ctiv
atio
n s
wit
ch(e
s)
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Up
to 1
10deg
111deg
to 1
80deg
15-1
2 (
394)
13-1
4 (
337)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull T
hick
ness
rec
omm
ende
d fo
r re
info
rcem
ents
in h
ollo
w
met
al d
oors
and
fram
es is
cha
rted
on
Pag
e 2
bull D
o no
t sca
le d
raw
ing
bull R
ight
han
d do
or s
how
nbull
Thi
s te
mpl
ate
info
rmat
ion
base
d up
on u
se o
f 5
(127
mm
) m
axim
um w
idth
but
t hin
ges
A s
epar
ate
tem
plat
e is
req
uire
d fo
r ot
her
cond
ition
sbull
Max
imum
fram
e re
veal
is 6
-78
rdquo (17
5mm
) fo
r th
is
appl
icat
ion
bull C
ondu
it ho
le n
eare
st th
e hi
nge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
2rdquo (
51m
m)
Min
F
ram
e Fa
ce
1-1
8rdquo(2
9)
1-1
4(3
2)1-
716
(37)
11(2
79)
22(5
59)
7-9
16(1
92)
13-7
16
(341
)
1-1
8(2
9)
C LH
inge
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)7
8 (2
3) D
ia
(2 P
lace
s)
38
Dia
S
ex N
uts
(3 P
lace
s)
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
3(7
6)
13-1
316
(350
)
12
(13)
A
11-1
116
(297
)
6rdquo
(152
mm
)M
in
Cle
aran
ce
14-3
16
(360
)
12-1
516
(329
)13
-13
16(3
51)
Rig
ht
Han
d D
oo
ro
pen
ing
to
110
deg sh
ow
n
58
(15
9)S
top
Left
Han
dD
oor
Rig
htH
and
Doo
r
2rdquo (
51m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
6rdquo (
152m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
ax
Do
or T
hic
knes
s
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Hin
ge
(Pu
ll) S
ide
app
licat
ion
as
sho
wn
on
th
is
tem
pla
te
Page 14
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Stop (Push) SideŸ Do not scale drawingŸ Left hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Dim
ldquoB
rdquo
Up
to 1
10deg
111deg
to 1
70deg
12 (
305)
9-1
2 (2
41)
13-1
4 (
337)
15-3
4 (
400)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull Thi
ckne
ss r
ecom
men
ded
for
rein
forc
emen
ts in
ho
llow
met
al d
oors
and
fram
es is
cha
rted
at t
he
left
of th
is p
age
bull D
o no
t sca
le d
raw
ing
bull Le
ft ha
nd d
oor
show
nbull T
his
tem
plat
e in
form
atio
n ba
sed
upon
use
of 5
(1
27m
m)
max
imum
wid
th b
utt h
inge
s or
34
(1
9mm
) of
fset
piv
ots
A s
epar
ate
tem
plat
e w
ill
be s
uppl
ied
for
othe
r co
nditi
ons
bull M
axim
um fr
ame
reve
al is
7rdquo (
178m
m)
for
this
ap
plic
atio
nbull
Con
duit
hole
nea
rest
to h
inge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
1-11
16
(43)
1-1
4(3
2)11
16
(17
5)
1-3
4(4
4)
12-1
516
(329
)
7-9
16(1
92)
13-7
16
(341
)
38
(10)
C LH
inge
or
Piv
ot
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)
78
(22)
(Con
duit
Hol
es -
2
Pla
ces)
Dia
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
A13-1
316
(351
)
12
(13)
B
5-1
4rdquoM
in
Cle
aran
ce
11-1
116
(297
)
38
(19)
14-3
16
(360
)13
-13
16(3
51)
Lef
t H
and
Do
or
op
en t
o 1
10deg
sho
wn
58
(15
9)S
top
Sex
Nu
ts(2
Pla
ces)
Left
Han
dD
oor
Rig
htH
and
Doo
r
1-1
2rdquo (
38m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
5-1
4rdquo (
133m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
axD
oo
r Th
ickn
ess
No
te D
oo
r m
ust
be
visi
ble
by
per
son
op
erat
ing
act
ivat
ion
sw
itch
(es)
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Sto
p (
Pu
sh)
Sid
e ap
plic
atio
n a
s sh
ow
n o
n t
his
te
mp
late
Page 15
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
3000 Highway 74 East bull Monroe NC 28112Tel (800)-438-1951 x4706 bull Fax (800)-338-0965
wwwnor tondoorcontrolscom
ASSA ABLOY
This PageLeft Blank
Page 16
ASSA ABLOY
Page 12
Troubleshooting
Red LEDBlue LED
Antenna Wire
Learnwo DelayButton
DelayPotentiometer(Time Adjustment)
Learn wDelay Button
DIP Switch
TerminalStrip
Problem The LED on my receiver is just flickering and Irsquom unable to program andor it wonrsquot workSolution You have a push plate stuck or faulty transmitter Disconnect each push plate until the LED goes out If LED
does not go out remove each transmitter battery until it does Replace the appropriate transmitterProblem Receiver intermittently doesnrsquot receive the transmitter(s) signal
Solution You may extend the receiver antenna wire only in multiples of 6-34rdquo (171) ie 675 x 4 = 27rdquo (686) of extended antenna wire
Removing Transmitter Code(s)
Single Transmitter CodeŸ Press both Delay and No Delay Buttons simultaneously until Red LED flashes once (approximately 1 second)Ÿ Press transmitter button twice within 10 seconds and the transmitter code will be deleted
All Transmitter CodesŸ Press and hold both Delay and No Delay Buttons simultaneously until Blue LED illuminates then release (approximately 10
seconds)
Push Plate Configuration
1 Before beginning it is easiest to have already prepared the installation of the push plate2 Connect the wires from the transmitter to the NO and COM contacts of the push platersquos switch3 Follow Steps 1 - 4 (Hand-Held Configuration) depress the push plate to activate the transmitter4 Attach the transmitter to the inside of the electrical box and complete the installation
Hand-Held Configuration
1 Set dip switches to the receiver to the desired activation cycle (dip switch 1 - Toggle or Pulse and dip switch 2 - 05s or 10s hold
2 Press either Learn w Delay Button or Learn wo Delay Button on the receiver depending on the activation requirements (if delay learn is selected adjust potentiometer to counterclockwise limit 0 second delay) Red LED on receiver will flash After learn cycle is complete adjust potentiometer to desired delay time (0 - 30 sec)
3 Depress transmitter button repeatedly until Blue LED on the receiver illuminates (indicating reception of signal from transmitter) NOTE Repeat Steps 2 - 3 to program additional transmitters
4 To test the system depress transmitter button (Red LED on Transmitter will illuminate) and observe that the Blue LED illuminates on the receiver This indicates that the relay has been activated
433MHz Receiver Userrsquos Guide
2OFFON
Description05s Hold Time10s Hold Time
FunctionRelay will remain active 05 sec after loss of activationRelay will remain active 10 sec after loss of activation
1OFF
ON
DescriptionPulse Relay
Toggle Relay
FunctionPress the transmitter once and the relay will be active momentarilyPress the transmitter once and the relay output is active indefinitely press it again and the relay will de-energize indefinitely
ON
1 2PU
L T
OG
05s
1
0s ON
1 2PU
L T
OG
05s
1
0sIn Toggle Setting (1-ON) the Hold Time is inactive Either setting for 2 dip switch will
have the same result
ON
1 2PU
L T
OG
05s
1
0s
05 second Pulse Setting
ON
1 2PU
L T
OG
05s
1
0s
10 second Pulse Setting
ŸAlways stop pedestrian traffic through the doorway when performing tests that may result in unexpected reactions by the door
ŸEnsure compliance with all applicable safety standards upon completion of installation
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
This PageLeft Blank
Page 13
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Hinge (Pull) SideŸ Do not scale drawingŸ Right hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
No
te D
oo
r m
ust
be
visi
ble
by
per
son
o
per
atin
g a
ctiv
atio
n s
wit
ch(e
s)
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Up
to 1
10deg
111deg
to 1
80deg
15-1
2 (
394)
13-1
4 (
337)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull T
hick
ness
rec
omm
ende
d fo
r re
info
rcem
ents
in h
ollo
w
met
al d
oors
and
fram
es is
cha
rted
on
Pag
e 2
bull D
o no
t sca
le d
raw
ing
bull R
ight
han
d do
or s
how
nbull
Thi
s te
mpl
ate
info
rmat
ion
base
d up
on u
se o
f 5
(127
mm
) m
axim
um w
idth
but
t hin
ges
A s
epar
ate
tem
plat
e is
req
uire
d fo
r ot
her
cond
ition
sbull
Max
imum
fram
e re
veal
is 6
-78
rdquo (17
5mm
) fo
r th
is
appl
icat
ion
bull C
ondu
it ho
le n
eare
st th
e hi
nge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
2rdquo (
51m
m)
Min
F
ram
e Fa
ce
1-1
8rdquo(2
9)
1-1
4(3
2)1-
716
(37)
11(2
79)
22(5
59)
7-9
16(1
92)
13-7
16
(341
)
1-1
8(2
9)
C LH
inge
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)7
8 (2
3) D
ia
(2 P
lace
s)
38
Dia
S
ex N
uts
(3 P
lace
s)
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
3(7
6)
13-1
316
(350
)
12
(13)
A
11-1
116
(297
)
6rdquo
(152
mm
)M
in
Cle
aran
ce
14-3
16
(360
)
12-1
516
(329
)13
-13
16(3
51)
Rig
ht
Han
d D
oo
ro
pen
ing
to
110
deg sh
ow
n
58
(15
9)S
top
Left
Han
dD
oor
Rig
htH
and
Doo
r
2rdquo (
51m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
6rdquo (
152m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
ax
Do
or T
hic
knes
s
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Hin
ge
(Pu
ll) S
ide
app
licat
ion
as
sho
wn
on
th
is
tem
pla
te
Page 14
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Stop (Push) SideŸ Do not scale drawingŸ Left hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Dim
ldquoB
rdquo
Up
to 1
10deg
111deg
to 1
70deg
12 (
305)
9-1
2 (2
41)
13-1
4 (
337)
15-3
4 (
400)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull Thi
ckne
ss r
ecom
men
ded
for
rein
forc
emen
ts in
ho
llow
met
al d
oors
and
fram
es is
cha
rted
at t
he
left
of th
is p
age
bull D
o no
t sca
le d
raw
ing
bull Le
ft ha
nd d
oor
show
nbull T
his
tem
plat
e in
form
atio
n ba
sed
upon
use
of 5
(1
27m
m)
max
imum
wid
th b
utt h
inge
s or
34
(1
9mm
) of
fset
piv
ots
A s
epar
ate
tem
plat
e w
ill
be s
uppl
ied
for
othe
r co
nditi
ons
bull M
axim
um fr
ame
reve
al is
7rdquo (
178m
m)
for
this
ap
plic
atio
nbull
Con
duit
hole
nea
rest
to h
inge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
1-11
16
(43)
1-1
4(3
2)11
16
(17
5)
1-3
4(4
4)
12-1
516
(329
)
7-9
16(1
92)
13-7
16
(341
)
38
(10)
C LH
inge
or
Piv
ot
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)
78
(22)
(Con
duit
Hol
es -
2
Pla
ces)
Dia
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
A13-1
316
(351
)
12
(13)
B
5-1
4rdquoM
in
Cle
aran
ce
11-1
116
(297
)
38
(19)
14-3
16
(360
)13
-13
16(3
51)
Lef
t H
and
Do
or
op
en t
o 1
10deg
sho
wn
58
(15
9)S
top
Sex
Nu
ts(2
Pla
ces)
Left
Han
dD
oor
Rig
htH
and
Doo
r
1-1
2rdquo (
38m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
5-1
4rdquo (
133m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
axD
oo
r Th
ickn
ess
No
te D
oo
r m
ust
be
visi
ble
by
per
son
op
erat
ing
act
ivat
ion
sw
itch
(es)
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Sto
p (
Pu
sh)
Sid
e ap
plic
atio
n a
s sh
ow
n o
n t
his
te
mp
late
Page 15
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
3000 Highway 74 East bull Monroe NC 28112Tel (800)-438-1951 x4706 bull Fax (800)-338-0965
wwwnor tondoorcontrolscom
ASSA ABLOY
This PageLeft Blank
Page 16
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
This PageLeft Blank
Page 13
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Hinge (Pull) SideŸ Do not scale drawingŸ Right hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
No
te D
oo
r m
ust
be
visi
ble
by
per
son
o
per
atin
g a
ctiv
atio
n s
wit
ch(e
s)
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Up
to 1
10deg
111deg
to 1
80deg
15-1
2 (
394)
13-1
4 (
337)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull T
hick
ness
rec
omm
ende
d fo
r re
info
rcem
ents
in h
ollo
w
met
al d
oors
and
fram
es is
cha
rted
on
Pag
e 2
bull D
o no
t sca
le d
raw
ing
bull R
ight
han
d do
or s
how
nbull
Thi
s te
mpl
ate
info
rmat
ion
base
d up
on u
se o
f 5
(127
mm
) m
axim
um w
idth
but
t hin
ges
A s
epar
ate
tem
plat
e is
req
uire
d fo
r ot
her
cond
ition
sbull
Max
imum
fram
e re
veal
is 6
-78
rdquo (17
5mm
) fo
r th
is
appl
icat
ion
bull C
ondu
it ho
le n
eare
st th
e hi
nge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
2rdquo (
51m
m)
Min
F
ram
e Fa
ce
1-1
8rdquo(2
9)
1-1
4(3
2)1-
716
(37)
11(2
79)
22(5
59)
7-9
16(1
92)
13-7
16
(341
)
1-1
8(2
9)
C LH
inge
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)7
8 (2
3) D
ia
(2 P
lace
s)
38
Dia
S
ex N
uts
(3 P
lace
s)
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
3(7
6)
13-1
316
(350
)
12
(13)
A
11-1
116
(297
)
6rdquo
(152
mm
)M
in
Cle
aran
ce
14-3
16
(360
)
12-1
516
(329
)13
-13
16(3
51)
Rig
ht
Han
d D
oo
ro
pen
ing
to
110
deg sh
ow
n
58
(15
9)S
top
Left
Han
dD
oor
Rig
htH
and
Doo
r
2rdquo (
51m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
6rdquo (
152m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
ax
Do
or T
hic
knes
s
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Hin
ge
(Pu
ll) S
ide
app
licat
ion
as
sho
wn
on
th
is
tem
pla
te
Page 14
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Stop (Push) SideŸ Do not scale drawingŸ Left hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Dim
ldquoB
rdquo
Up
to 1
10deg
111deg
to 1
70deg
12 (
305)
9-1
2 (2
41)
13-1
4 (
337)
15-3
4 (
400)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull Thi
ckne
ss r
ecom
men
ded
for
rein
forc
emen
ts in
ho
llow
met
al d
oors
and
fram
es is
cha
rted
at t
he
left
of th
is p
age
bull D
o no
t sca
le d
raw
ing
bull Le
ft ha
nd d
oor
show
nbull T
his
tem
plat
e in
form
atio
n ba
sed
upon
use
of 5
(1
27m
m)
max
imum
wid
th b
utt h
inge
s or
34
(1
9mm
) of
fset
piv
ots
A s
epar
ate
tem
plat
e w
ill
be s
uppl
ied
for
othe
r co
nditi
ons
bull M
axim
um fr
ame
reve
al is
7rdquo (
178m
m)
for
this
ap
plic
atio
nbull
Con
duit
hole
nea
rest
to h
inge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
1-11
16
(43)
1-1
4(3
2)11
16
(17
5)
1-3
4(4
4)
12-1
516
(329
)
7-9
16(1
92)
13-7
16
(341
)
38
(10)
C LH
inge
or
Piv
ot
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)
78
(22)
(Con
duit
Hol
es -
2
Pla
ces)
Dia
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
A13-1
316
(351
)
12
(13)
B
5-1
4rdquoM
in
Cle
aran
ce
11-1
116
(297
)
38
(19)
14-3
16
(360
)13
-13
16(3
51)
Lef
t H
and
Do
or
op
en t
o 1
10deg
sho
wn
58
(15
9)S
top
Sex
Nu
ts(2
Pla
ces)
Left
Han
dD
oor
Rig
htH
and
Doo
r
1-1
2rdquo (
38m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
5-1
4rdquo (
133m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
axD
oo
r Th
ickn
ess
No
te D
oo
r m
ust
be
visi
ble
by
per
son
op
erat
ing
act
ivat
ion
sw
itch
(es)
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Sto
p (
Pu
sh)
Sid
e ap
plic
atio
n a
s sh
ow
n o
n t
his
te
mp
late
Page 15
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
3000 Highway 74 East bull Monroe NC 28112Tel (800)-438-1951 x4706 bull Fax (800)-338-0965
wwwnor tondoorcontrolscom
ASSA ABLOY
This PageLeft Blank
Page 16
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Hinge (Pull) SideŸ Do not scale drawingŸ Right hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
No
te D
oo
r m
ust
be
visi
ble
by
per
son
o
per
atin
g a
ctiv
atio
n s
wit
ch(e
s)
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Up
to 1
10deg
111deg
to 1
80deg
15-1
2 (
394)
13-1
4 (
337)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull T
hick
ness
rec
omm
ende
d fo
r re
info
rcem
ents
in h
ollo
w
met
al d
oors
and
fram
es is
cha
rted
on
Pag
e 2
bull D
o no
t sca
le d
raw
ing
bull R
ight
han
d do
or s
how
nbull
Thi
s te
mpl
ate
info
rmat
ion
base
d up
on u
se o
f 5
(127
mm
) m
axim
um w
idth
but
t hin
ges
A s
epar
ate
tem
plat
e is
req
uire
d fo
r ot
her
cond
ition
sbull
Max
imum
fram
e re
veal
is 6
-78
rdquo (17
5mm
) fo
r th
is
appl
icat
ion
bull C
ondu
it ho
le n
eare
st th
e hi
nge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
2rdquo (
51m
m)
Min
F
ram
e Fa
ce
1-1
8rdquo(2
9)
1-1
4(3
2)1-
716
(37)
11(2
79)
22(5
59)
7-9
16(1
92)
13-7
16
(341
)
1-1
8(2
9)
C LH
inge
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)7
8 (2
3) D
ia
(2 P
lace
s)
38
Dia
S
ex N
uts
(3 P
lace
s)
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
3(7
6)
13-1
316
(350
)
12
(13)
A
11-1
116
(297
)
6rdquo
(152
mm
)M
in
Cle
aran
ce
14-3
16
(360
)
12-1
516
(329
)13
-13
16(3
51)
Rig
ht
Han
d D
oo
ro
pen
ing
to
110
deg sh
ow
n
58
(15
9)S
top
Left
Han
dD
oor
Rig
htH
and
Doo
r
2rdquo (
51m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
6rdquo (
152m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
ax
Do
or T
hic
knes
s
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Hin
ge
(Pu
ll) S
ide
app
licat
ion
as
sho
wn
on
th
is
tem
pla
te
Page 14
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Stop (Push) SideŸ Do not scale drawingŸ Left hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Dim
ldquoB
rdquo
Up
to 1
10deg
111deg
to 1
70deg
12 (
305)
9-1
2 (2
41)
13-1
4 (
337)
15-3
4 (
400)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull Thi
ckne
ss r
ecom
men
ded
for
rein
forc
emen
ts in
ho
llow
met
al d
oors
and
fram
es is
cha
rted
at t
he
left
of th
is p
age
bull D
o no
t sca
le d
raw
ing
bull Le
ft ha
nd d
oor
show
nbull T
his
tem
plat
e in
form
atio
n ba
sed
upon
use
of 5
(1
27m
m)
max
imum
wid
th b
utt h
inge
s or
34
(1
9mm
) of
fset
piv
ots
A s
epar
ate
tem
plat
e w
ill
be s
uppl
ied
for
othe
r co
nditi
ons
bull M
axim
um fr
ame
reve
al is
7rdquo (
178m
m)
for
this
ap
plic
atio
nbull
Con
duit
hole
nea
rest
to h
inge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
1-11
16
(43)
1-1
4(3
2)11
16
(17
5)
1-3
4(4
4)
12-1
516
(329
)
7-9
16(1
92)
13-7
16
(341
)
38
(10)
C LH
inge
or
Piv
ot
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)
78
(22)
(Con
duit
Hol
es -
2
Pla
ces)
Dia
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
A13-1
316
(351
)
12
(13)
B
5-1
4rdquoM
in
Cle
aran
ce
11-1
116
(297
)
38
(19)
14-3
16
(360
)13
-13
16(3
51)
Lef
t H
and
Do
or
op
en t
o 1
10deg
sho
wn
58
(15
9)S
top
Sex
Nu
ts(2
Pla
ces)
Left
Han
dD
oor
Rig
htH
and
Doo
r
1-1
2rdquo (
38m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
5-1
4rdquo (
133m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
axD
oo
r Th
ickn
ess
No
te D
oo
r m
ust
be
visi
ble
by
per
son
op
erat
ing
act
ivat
ion
sw
itch
(es)
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Sto
p (
Pu
sh)
Sid
e ap
plic
atio
n a
s sh
ow
n o
n t
his
te
mp
late
Page 15
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
3000 Highway 74 East bull Monroe NC 28112Tel (800)-438-1951 x4706 bull Fax (800)-338-0965
wwwnor tondoorcontrolscom
ASSA ABLOY
This PageLeft Blank
Page 16
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
Removable Template - Stop (Push) SideŸ Do not scale drawingŸ Left hand door shownŸ All dimensions given in inches (mm)Ÿ Maximum frame reveal is 18rdquo (3 mm)
for this application
Do
or
Op
enin
gA
ng
leD
im ldquo
Ardquo
Dim
ldquoB
rdquo
Up
to 1
10deg
111deg
to 1
70deg
12 (
305)
9-1
2 (2
41)
13-1
4 (
337)
15-3
4 (
400)
No
tes
bull A
ll di
men
sion
s ar
e gi
ven
in in
ches
(m
m)
bull Thi
ckne
ss r
ecom
men
ded
for
rein
forc
emen
ts in
ho
llow
met
al d
oors
and
fram
es is
cha
rted
at t
he
left
of th
is p
age
bull D
o no
t sca
le d
raw
ing
bull Le
ft ha
nd d
oor
show
nbull T
his
tem
plat
e in
form
atio
n ba
sed
upon
use
of 5
(1
27m
m)
max
imum
wid
th b
utt h
inge
s or
34
(1
9mm
) of
fset
piv
ots
A s
epar
ate
tem
plat
e w
ill
be s
uppl
ied
for
othe
r co
nditi
ons
bull M
axim
um fr
ame
reve
al is
7rdquo (
178m
m)
for
this
ap
plic
atio
nbull
Con
duit
hole
nea
rest
to h
inge
is s
ugge
sted
for
120
VA
C p
ower
inpu
t
1-11
16
(43)
1-1
4(3
2)11
16
(17
5)
1-3
4(4
4)
12-1
516
(329
)
7-9
16(1
92)
13-7
16
(341
)
38
(10)
C LH
inge
or
Piv
ot
14-
20 M
ach
ine
Scr
ews
or
No
14
Wo
od
Scr
ews
(6 P
lace
s)
78
(22)
(Con
duit
Hol
es -
2
Pla
ces)
Dia
Fra
me
Rab
bet
Fra
me
Sto
pS
off
it
A13-1
316
(351
)
12
(13)
B
5-1
4rdquoM
in
Cle
aran
ce
11-1
116
(297
)
38
(19)
14-3
16
(360
)13
-13
16(3
51)
Lef
t H
and
Do
or
op
en t
o 1
10deg
sho
wn
58
(15
9)S
top
Sex
Nu
ts(2
Pla
ces)
Left
Han
dD
oor
Rig
htH
and
Doo
r
1-1
2rdquo (
38m
m)
Min
Fra
me
Face
Fra
me
Rev
eal
Door
5-1
4rdquo (
133m
m)
Min
Cei
ling
Cle
aran
ce
1-3
4rdquo (
44m
m)
Min
2-
14rdquo
(57
mm
) M
axD
oo
r Th
ickn
ess
No
te D
oo
r m
ust
be
visi
ble
by
per
son
op
erat
ing
act
ivat
ion
sw
itch
(es)
Ple
ase
veri
fy d
esir
ed m
ou
nti
ng
re
qu
ires
Sto
p (
Pu
sh)
Sid
e ap
plic
atio
n a
s sh
ow
n o
n t
his
te
mp
late
Page 15
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
3000 Highway 74 East bull Monroe NC 28112Tel (800)-438-1951 x4706 bull Fax (800)-338-0965
wwwnor tondoorcontrolscom
ASSA ABLOY
This PageLeft Blank
Page 16
ASSA ABLOY
Nortonreg is a registered trademark of Yale Security Inc an ASSA ABLOY Group company Copyright copy 2015 Yale Security Inc an ASSA ABLOY Group company All rights reserved Reproduction in whole or in part without the express written permission of Yale Security Inc is prohibited 80-9357-0008-020 (Rev 3)
3000 Highway 74 East bull Monroe NC 28112Tel (800)-438-1951 x4706 bull Fax (800)-338-0965
wwwnor tondoorcontrolscom
ASSA ABLOY
This PageLeft Blank
Page 16
ASSA ABLOY