24 Upright Owners Clean Household Type Guide Z4700 Series Vacuum e r 4 5 58 9 10 11 11 11 12 12 12 13 15 IMPORTAN T Please read theseinstructions for advice on the maintenance of your cleaner.

13 13 14

IMPORTANT INFORMATION GUARANTE E QUICK REFERENCE HOW TO ASSEMBLE HOW TO USE ROUTINE MAINTENANCE Empty Dust Cup Clean Dust Cup Filter PERIODIC MAINTENANCE Brushrol l Brushroll Belt PROBLEM SOLVING Clear Hose Thermal Cut Off Mini Turbo Nozzle

FILTER EF86b

REPLACEMENT

CODE:

www.electrolux.co.uk

IMPORTANT SAFEGUARDSWhen using an electrical appliance, basic precautions should always be followed, clud ing in following: READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER. the

WARNING

To reduce the risk of fi re, electric shock, or injury: Do not use outdoors or on wet surfaces. leave vacuum cleaner whilst plugged in. Do not Turn off the switch and unplug the electrical cord when not use and before in servicing. DO NOT PLACE CLEANER ON FURNITURE OR STAIRS AS THE BRUSHROLL MAY CAUSE Place cleaner oor with the handle in the storage position while using DAMAGE. on attachments. Do not allow to be used as a toy. Close attention is necessary when used by or near children. as described in this manual. Use only manufacturers recommended Use only attachments. Do not use with damaged cord or plug. If vacuum cleaner is not working as it should, has been dropped, left dam outdoors, or dropped into water, return it to a service centre before using. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or Do not corners. run vacuum cleaner over cord. Keep cord away from heated surfaces. Do not use extension cords or outlets with inadequate current carrying capacity. Turn off all controls before unplugging. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord. Do not handle plug or vacuum cleaner with wet hands. Do not put any object into openings. Do not use with any opening blocked; keep free of dust, lint, hair, and anything may reduce air that ow. This vacuum cleaner creates suction and contains a revolving brushroll. Keep hair, loose clothing, fi ngers, and all of parts body away from openings and moving Doparts.pick up anything that is burning or smoking, such as cigarettes, matches, or hot not ashes. use without the dust cup or fi lter(s) in Do not place. Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt pulley when servicing the drive belt. extra care when cleaning on Use stairs. use to pick up ammable or combustible liquids such as gasoline, or use in areas where they may be Do not present. Store your cleaner indoors in a cool, dry area. your work area well Keep lighted. Unplug electrical appliances before vacuuming them.

aged ,

PLEASE SAVE INSTRUCTIONS

THESE

The symbol on the product or on its packaging indicates that this product may not be treated as household Instead waste. it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the By and human environmenthealth, which could otherwise be caused by inappropriate waste handling of this product. For more information about recycling of this product, please contact your local city offi ce, your household waste disposal service detailed the or shop where you purchased the product. 2

BEFORE YOU STARTCHECK THE VOLTAGE Before connecting the cleaner to an electrical supply, ensure that the voltage shown on the rating plate located beneath thecleaner correct voltage for your electricity supply. If it is not, do not use the cleaner but refer back to your is of the dealer.

CONNECTING TO YOUR TRI ITY Permanently connected to the er is a mains supply (2-core) cable fi tted with a non-rewirable plug incorporating a 13A ELEC C SUPPLY

clean event of the fuse requiring replacement the fuse cover should be fuse. In the moved using a small dri er. The old MUST re re placed by a 13A ASTA proved BS1362 fuse or a BSI approved fuse. The cover must be screw v fuse be placed before the plug is re used again. ap the event of loss of the fuse cover, In place ments can be obtained from your Electrolux Retailers and must be of re the same colour as indicated by the oured insert on the base of the coldiffi culty is pe rienced in tai ing a replacement, plug. If tact Electrolux Customer Services on 08706 055 ex no circumstances must the plugnbe used without a correct fuse cover fi tted. ob con 055. In If the plug that is fi tted to your appliance is not suitable for your socket outlet, it must be cut off and the appropriate plug fi tted. the fuse from the cut off Remove plug.cut off plug should then be The posed of to prevent the hazard of shocks in case it should be plugged into a 13 amp dis another part of your socket in home. The wires in the mains cable of this appliance are coloured in cord ance with the following Blue: Neu tral. Brown: Live. ac the colours of the wires in the mains cable of this appliance may not correspond with code: As oured markings the col iden terminals in your plug, proceed as follows: which is coloured blue must be The wire nect ed to the terminal which is marked with the letter N or coloured con wire which is coloured brown must be black. The nect ed to the terminal which is marked with the letter L or coloured con red. If using a three-pin plug, do not make any nec tion to the terminal marked with the letter E or by the earth symbol or con or green-and-yellow. This cleaner is green ble colsu lated and no earth nec tion is es sary. dou in your interest to ensure that the plug is correctly attached to the mains cable. In case ofnec in con It is doubt, consult a qualifi ed elec as Electrolux cannot regard the repair of faults on the plug connection as a service that can be given free of charge under the of terms the guarantee. 13 Amp Fuse t fying i the

oure d tr cian i ,

Cover

Fuse

Fuse Blue Brown

WARNING

Cord Clamp

The brush in the cleaning head rotates at high speed and can cause damage to the mains supply cable if the cleaner passes over it during cleaning operations. Care should be taken to ensure that this does not happen. If the cleaning head has accidentally passed over the mains supply cablefollowing action should be the taken: 1. Switch off and remove the plug from the socket outlet. 2. Examine the mains supply cable for damage (only after removing the plug from the socket 3.outlet).supply cord is damaged it must be replaced by a Electrolux Service Agent or similar qualifi ed person in order to If the avoid a hazard 4. . NEVE use the machine with a damaged mains supply R Proprietarycable. conditioning and air freshening carpet te rials ma using proprietary carpet conditioning powders, it is recommended that the fi lters be changed. Some of these preparations After contain es which, if left in the vacuum cleaner for extended periods, could damage the plastic mouldings which form the sub stanc structure of the cleaner. fresheners, household deodorants, sprays and polishes contain a highly Many air ma ble gas am propellant. Because of this, it is particularly important that these products are used strictly cord ance with the in ac manufacturers instructions . t is essential that none of the above products are sprayed directly into the vacuum cleaner or any of its fi lters, hose assembly, I dustbag or dust chamber cup.

relevant

Thermal Cut OffThis vacuum cleaner has a special thermostat that protects the cleaner in case of motor overheating. If the cleaner switches off, push the switch pedal once and unplug the cleaner. Check the cleaner for a possible source of overheating such as a full dust cup, a blocked hose or fi lter. If these conditions are found, fi x them and wait at least 60 minutes before attempting to use the cleaner. After the 60 clogged minute plug the cleaner back in and push the on/off switch On (I). If the cleaner still does not run, please call Electrolux Customer period, Care.

3

SERVICEShould you require service on your Electrolux cleaner, please telephone Electrolux Customer Services on 08706 055 055. Before requesting service, please check whether your problem is covered under Service Checklist (see below). New fi lter pads, brushrollers and drive belts can be obtained from Electrolux Retailers. If diffi culty is experienced in obtaining spares, please contact Electrolux on 08706 055 055.

SERVICE Ifyour cleaner will not operate, check the plug connection, plug fuse and mains CHECKLIST

fuse. Never allow the dust cup to become so full that it impedes the air ow, thus reducing the cleaning effi ciency of the machine. The character of household dust and its effect on the air ow through the machine may vary considerably. Fluffy dust allowspass through readily whereas fi ne powdery dust or proprietary cleaning powders, pack tightly in the dust cup, air to offeringresistance to air ow and will reduce cleaning effi ciency if the cup becomes greater overloaded. Always store your cleaner and spare dust fi lters in a dry place. Renew the fi lter pads three or four times a year. This is essential to ensure continued high fi ltration of dust Suckingparticles. items as stockings, clippings of cloth, sizeable pieces of paper, wrappings from cigarette packets or such up may block the sweets etc., Electrolux regrets that the clearing of blocked hoses cannot be regarded as service that can hose. be given free of charge, under the guarantee. Should a blockage occur, fi rst disconnect the cleaner from the electricity supply, refer to section headed ag es. If these op era tions are not cess ful, contact Electrolux on 08706 055 suc 055. Block pick up hot cinders or lighted cigarette Never ends. Make certain that your cleaner does not come into contact with water or any other liquid. It is not designed as a wet pick up cleaner, and must never be used on damp carpets or wet oors. Important - If the supply cord is damaged it must be replaced by a Electrolux Service Agent or similar qualifi ed person in order avoid to a hazard.

Spares

New fi lters, brushrollers and drive belts can be obtained from Authorised Electrolux Dealers and electrical retailers. If diffi culty is experienced in obtaining spares please call us on 08706 055 055 or visit our website at www.shop.electrolux.co.uk

GUARANTEEThis guarantee is in addition to your statutory and other legal rights. This product is for household use only. Electrolux products are carefully designed, manufactured, tested and inspected and, in consequence, we undertake to replace or part found to be defective in materials or workmanship, within one year of delivery to the original purchaser, free of repair any charge. be required to take the product to your nearest service provider if the product requires attention during the fi rst You may year. There are certain conditions which may invalidate this guarantee: a.It is dependent upon the appliance being correctly installed and used in accordance with the Companys instructions under normal domestic conditions within the United Kingdom or the Republic of Ireland. b.Service at all times must be carried out by an Electrolux Service Representative or authorised agent. c. The guarantee may be invalidated by unauthorised repair or modifi cation of the appliance. d.You may be charged by Electrolux if you call for an engineer to resolve a problem that we believe is covered in the instruction booklet. (example: blocked/dirty fi lters) Electrolux does not accept liability for all defects arising from neglect, misuse or accident. This guarantee excludes such normal wearing drive belts, brushes and fi lters as the life of these depends upon the amount and nature of parts as use. of purchase will be required before service under guarantee is provided. Please call 08706 055 055 for Proof assistance. IMPORTANT : or future reference we suggest you record the following details here, and keep the receipt with the handbook as proof of F purchase. from ____________________________________________________ Purchased Date purchased __________________ Model no __________________________

101 Oakley Road, LUTON, BEDFORDSHIRE, LU4 9QQ Features of the Electrolux vacuum cleaner and ces so ries supplied with it are tect ed in Great Britain and abroad by Patents or ac pro Registered Designs . This appliance conforms with the requirements of the ed E.E.C. directive No. 89/336/EEC lat ing to tromag net ic amend re elec compatibility (EMC) CE. Electrolux may introduce modifi cations to their product from time to time, se quen ly the details given in this booklet are and con t subject to alteration without notice.

4

Quick ReferenceA C

B

EF G G1

AWan d BCrevice Tool CDusting Brush DHose EBase F Dust Cup with Lid and Filter GHandle G1Turbo ( Handle) HTool Caddy IRear Housing JHose Retainer KStair Brush

D

K

H Stair Brush (some models only) JI

How To Assemble CAUTION: Assemble the cleanerusing.

completely before

L1

NOTE: All screws must be installed to properly secure the parts of the vacuum. CAUTION: Moving parts, make sure the on/off switch is in the off position and stay clear of the brushroll when plugging in. NOTE: Features may vary by model yet all parts assemblethe same. Remove all components from the carton and check that all of the partsavailable from the parts list are above. Have a Phillips screwdriver available (one is NOT provided in the package) .

L2

(NOT provided package)

in

the

5

How Assemble

To

(continued)E

I to the base Step 1: Assemble the rear housing by sliding it on top of the base and attaching to the base using a long screw L2. (FIG. 1) provided

FIG. 1

I

L2

E H to the top of the rear Step 2: Attach the tool housing caddy sliding it onto the housing, lining up I by the screw holes, and then attaching it using the 2 short screws L1 provided. (FIG. 2)

FIG. 2L1 L1 H

I

FIG. 3G to top of tool caddy Hb Step 3: Attach the handle sliding it downward and then securing with a long y screw L2. (FIG. 3) G

L2

H

6

How Assemble

Tothe the

(continued)

FIG. 4 hose rear the hose Iwith 2 short screwsD to

Step 4: Secure assembly connection on housing 4). L1 (FIG.

D L1 L1 I

Step 5: Thread the hose inside the lower hose retainer J and then attach the lower hose retainer to the rear L1 (FIG. 5). housing I with a short screw

FIG. 5

I

L1 J

Step 6: Pull the electrical cord up to the cord retainer and fi rmly push into the retainer (FIG. 6a). This will the cord out of the way for next use. Wrap the keep cord the carrying handle on the tool caddy and around then around the cord release hook. (FIG. wrap 6) FIG. 6a

FIG. 6

7

How Assemble Step 7:

To

(continued)

Then wrap the hose up and over the hose hook G as shown. Plug the end of the on the handle hose retainer hole on the hose into the E (FIG. 7a) base then snap the hose into the hose holder on and the caddy H. (FIG. 7b) tool

FIG. 7

FIG. 7a

G E H

FIG. 7b

Step 8: Place the dust cup F on the vacuum by aligning the bottom groove of the dust cup against the tab on cleaner base. Pivot the dust cup up against cleaner and to secure as it snaps into place. (FIG. push 8) Step 8A: (in some models only). Place stair brush in slot in the special handle holder. (FIG. 8a)

FIG. 8

FIG. 8aF

A / B tool in the Step 9: Place the wand/crevice wand holder on the side of the vacuum. Store the C on the brush holder on the dusting brush back of the handle. (FIG. 9)

FIG. 9C B

A

8

How Use

ToCAUTION: Do not plug in cleaner until you understand all controls and features. FIG. 10

Plug in Vacuum (FIG. 10). Unwrap the cord by turning the quick release cord hook (FIG. 10a), unwind the cord and plug into an appropriate outlet.

FIG. 10a Put Cord on Cord To use, push Retainer. cord down into cord retainer (FIG. electrical 11a). will fi nd your cord retainer on the You handle the upper cord hook. This will place above the out of the way the next time you cord vacuum. (FIG. 11) FIG. 11

ON/OFF Switch PedalThe ON/OFF Switch Pedal is on the base. Press to turn on and press again to turn off. once (FIG.12) Cleaner Height Setting (FIG. 12a) The cleaner has an adjustment that raises or lowers the cleaner base to match the type of oor surface. With the cleaner cord unplugged, set the adjustment to lowest setting for maximum carpet cleaning If the cleaner is diffi cult to push, . move adjustment to next highest setting until cleaner is comfortable to The brushroll must push. the carpet for effective cleaning. For reach ease in moving the adjustment knob, place handle in operating position and tilt cleaner back to remove weight from front wheels. WARNING: Avoid injury. Keep loose clothing, hair, fi ngers, and all other parts of body away from any moving part (such as the revolving brush). FIG. 11a

FIG. 12

FIG. 12a

9

How To (continued) Use Stair CleaningPlace the cleaner on the oor with the back of the cleaner the stair riser. An additional stair hose can against be purchased if required. Please ring Electrolux Customer Care on 08706 055 055. CAUTION: Do not place the cleaner on stairs or on a stair above you when cleaning stairs.

Use Handle ReleaseStep on handle release (FIG. 14a) pull handle back to a and comfortable position. Press again to lower handle to clean under furniture. Return to further full upright position to use the hose and attachments. (FIG. 14) HELPFUL HINT: Before cleaning under low furniture, check fi rst for area objects that might harm the or block unit the vacuum hose.

FIG. 14

14a

How To Use AccessoriesCAUTION: Do not place cleaner on furniture or steps for any period of time as the brushroll may cause damage. Place cleaner on oor with the handle in storage position while using accessories. Do not allow cleaner to tilt forward when using accessories. Remove hose from hose adapter on the base of cleaner. Place desired accessory onto end of hose or wand. Nested Extension A to add reach. Grasp Wand near ridges. Pull apart. Turn ridge end to both wands center. wands together. (FIG. Push 15) Crevice Tool B cleans corners, baseboards and cushions. between Dusting/Upholstery C is for furniture, blinds, Brush lampshades, shelves, curtains, draperies, books, cushions and fabrics. NOTE: When using on hard oors an additional hard oor nozzle is available. Please ring Electrolux Customer Care on 08706 055 055.10

FIG. 15

B

C

A

ROUTINE MAINTENANCE switch and unplug the electrical NOTE: Turn off thecord

Empty Dust Cup

before routine maintenance. Never operate the vacuum cleaner without the dust cup fi lter in place.

FIG. 16

16a

Lift up the latch and pull out to release the dust cup from the housing. To open, turn dust cup lid counter clockwise (move to OPEN position) (FIG. 16a) then grasp dust cup lid and pull dust cupout and away from the cup (FIG. 16b). The fi lter stays attached lid to lid to make it easier to empty any dust or dirt from the cup the intotrash without touching the fi lter (FIG.16c). Just hold the lid the and the fi lter on the edge of the trash can to clean. After cleaning tap the fi lter, place the lid back on the cup, rotating it clockwise until it points LOCK symbol. (FIG. to the 16)

16b

Clean Dust Cup Filter, EF86bNOTE: Turn off the switch and unplug the electricalcord before changing the Pleated Filter. Never the vacuum cleaner without the dust operate cupthe pleated fi lter assembly. To maintain or good performance, check the Pleated Filter each timedust cup is emptied and clean if needed. the The can be cleaned by rinsing it with warm fi lter water. pleated fi lter is completely dry Be sure before reinstalling . Cleaning the Pleated Filter: Step 1: Step 2: Step 3: Remove the dust cup lid assembly by turning the lid clockwise and lifting upward and out of the dust counter cup. Grasp the pleated fi lter and turn counter clockwise to (FIG. remove. 17) Shake off dust and hair from fi lter into the trash. Brush between pleats to remove dust and debris. To wash, inonly rinse with warm water. Shake excess water from fi lter. Do submerge fi lter not assembly. Step When all parts are completely dry, replace pleated fi lter turn clockwise to lock in 4: and place. Step Allow fi lter to dry for 24 hours before 5: reusing. CAUTION: The dust cup can be washed in warm water, if desired, but strong detergents should not be used. thoroughly before using Dry again.

16c

FIG. 17

FIG. 18

Emptying The Dust Cup:

It is clearly visible when the dust cup is full and needs emptying. There line to help determine when the cup is full. Remove dust cup a fi ll is from cleaner body, remove the lid and dump debris in a waste container. Reinstalling The Dust Cup: To mount the fi lter assembly into cleaner body, make certain the fi lter assembly is fully seated in top of dust cup lid (FIG. 18). Replace dust by aligning front of the bottom of dust cup into groove on cup cleaner. cup up against cleaner and push in place until the dust Pivot dust cup latch is secure.

11

PERIODIC MAINTENANCE CAUTION: Turn offelectrical

Brushroll

the switch and unplug the cord before replacing belt. Motor shaft can become hot during normal use. To prevent avoid touching the motor shaft injury, when checking the belt. (FIG. 20 )

The brushroll turns as it sweeps and combs the carpet nap. Remove threads from the brushroll so it continues brushing hair and the carpet. To maintain the most effi cient cleaning, the bristles must the carpet. To test the bristle length, hold a ruler against touch the underneath side of the cleaner. If the bristles no longer touch the ruler, replace the brushroll.

19a

Brushroll Belt

Brushroll Performance Window (FIG. 19). To check condition watch to see if white dots on the belt are of the belt moving the performance window (FIG. 19a). This through indicates the brushroll is turning. The brushroll belt turns the brushroll to agitate, sweep, and comb the carpet nap. Check the belt regularly to be sure it is in good condition. Replace the belt if it stretches, cracks or loses tension. any hair or threads wound around the brushroll or Cut away the pulley because the buildup could cause the belt to belt rotate unevenly . NOTE: Ensure that objects such as edges and fringes of rugs do not stop the rotation of the brushroll.

FIG. 19

To Change BeltStep 1: Step 2: Step 3: Step 4: Step 5: Step 6: Step 7: Step 8: Step 9: Step 10: Step 11: Step 12: Lower handle to oor to change belt. Remove two screws to release hood (FIG. 19). hood to expose belt and brushroll (FIG. Lift 20). Lift left end of brushroll and pull out of base. Remove and discard belt. debris from brushroll area. Clean Clean any urnt rubber from motor shaft using fi b ne sandpaper or an emery board. Place new belt around motor shaft. belt around right side of Place brushroll. side of brushroll to stretch belt. Pull right Secure end cap into right base. Align left end cap with square in base. Push end cap into place. Rotate brushroll to position belt on brushroll pulley. Replace the hood. Tighten screws. NOTE: Use ELECTROLUX replacement ZE090. only GENUINE brushroll belt, Code

Motor Shaft

FIG. 20

12

PLEASE NOTE: The new belt will be smaller in diameter compared with the used Therefore, it belt. will require stretching into place. This is normal.

How to Check and Clear Hose BlockagesLow suction or poor pick-up may be due to a lockage in the vacuum b cleaner. Step Remove hose from hose retainer on 1: the and check suction at end of hose. base If little or no suction, check dust cup. Empty if needed. If no improvement, proceed to 2. step CAUTION: Turn off the switch and unplug the electrical cord before hose. clearing Step 2: Remove electrical cord from cord hooks. Disconnect the clear tube by unscrewing the 2 screws, then lift away from cleaner.for any obstructions that may Check be the tube or hose. Obstructions in may removed by using a blunt be instrument tube or hose. Flexing to clear the the may help loosen the blockage. hose After blockage, reverse above steps clearing to reassemble unit. (FIG. 21)

Thermal Cut-Off

This cleaner has a special thermostat that protects the cleaner in case of motor overheating. If the cleaner suddenly turns off, follow this procedure: Step Push on/off switch to 1: off. Step Unplug 2: cleaner. Step Check for source of overheating 3: problem (i.e. full dust cup, clogged hose or clogged fi lters). Step If a full dust cup, clogged hose or 4: clogged are found, empty the dust fi lters cup, unclog the hose or replace the fi lters. Step Wait at least 30 minutes before 5: attempting to reuse the cleaner. Step After a 30-minute cool down period, 6: plug cleaner in and push the switch the pedal. The cleaner should turn on. Step If the cleaner still does not 7: operate, call Electrolux Customer Care please on 08706 055 055.

FIG. 21

13

Models equipped with Mini Turbo NozzleThis convenient air-driven Turbo Nozzle is perfect for on upholstery, stairs and area rugs. Turbo Nozzle use is designed for use on end of hose.

Maintenance Instructions:To remove any clogs or debris from around the brushroll or belt of the turbo, follow the steps below:Screws

Step 1:

To open Turbo Nozzle, unscrew the two screws on the side (as (2) pictured).

Step 2:

Lift up housing.

the

bottom

Step 3:

Clear blockage from brushroll area.

Step 4:

To close align top and bottom housings and tighten with the two (2) screws.

14

Problem Cause SolutionMotor will not start. Electric Plug Push plug securely into outlet. Try another outlet. Check circuit breaker. to page Refer 3. Motor suddenly stops. Thermal Cut Off Refer to page 13. not clean the carpet/ oor. Dust Cup Empty the dust Does cup.Make sure dust cup is installed properly and Filter Make sure pleated fi lter is clean. Replace broken, loose, out-of-shape Belt belt. Brushroll Clean hair and thread from bristles and end Replace brushroll if bristles are worn. Remove any clogs from the hose that Hose restrict Refer to pages 11, 12, and 13. suction at the hose. Dust Cup and Filter Empty the dust No cup. Clean and install fi lter properly. sure dust cup is installed properly Make and Hose restrict Remove any clogs from the hose that dust cup secured. latch is

cap area. the ow. air

dust cup secured. the ow. air

latch

Check both ends of the hose. Refer to pages 11 and 13. from the brushroll area. Brushroll Remove hood and clean debris from Noise brushroll the area. Belt Replace broken, loose, out-of-shape belt. Refer to page 12. Cleaner is hard to push. Cleaner Height Setting Put handle in operating position. Tilt cleaner back to raise the front wheels off the oor. the Then turn the knob to a higher setting. Refer to page 9. Cleaner height knob will not turn. Cleaner Height Setting Replace broken, loose, out-of-shape belt.Refer to pages 9 and 12. Brushroll will not turn. Brushroll Remove hood and clean debris from the Hint:Put handle in operating position. Tilt cleaner back to raise the front wheels off the oor. the Then turn the knob.

Refer to page 12. Burning smell. Belt Remove hood and clean debris from brushroll and belt the area. Refer to page 12. brush doesn't work. Brushroll/Belt Remove any clogs from the opening or Stair around the brushroll or debris belt. Refer to page 14. Missing parts. the More questions? the Call Electrolux on 08706 055 055. Have model and call. See you cleaner. model and call. you See cleaner. serial numbers ready when rating plate beneath the serial numbers ready when rating plate beneath the 15

brushroll area.

Call Electrolux on 08706 055 055. Have

If you experience any problems with your cleaner, dont struggle taking it back to the shop.

Call our dedicated Customer Helpline for help advice and also to order fi lters and and accessories.

08706 055 055in

Items CartonDusting Brush Wan d Base

thisHandle Rear Housing

Screws

Dust Cup Lid with and Filter

Stair Brush (on some models only) Hose Crevice Tool

Tool Cadd y

Hose Retainer

Thank you for an purchasing Electrolux cleaner. Forget to DontUse Genuine Parts ElectroluxCaution: Damages caused by the use of non-genuine parts not covered by the Electrolux are Guarantee.

Part No. 75598B_REV 1

(09/06)

Printed PRC

in