To see the complete KADO range go to www.reece.com.au/bathrooms

Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.

Tech Page Version 5

ASPECT

SPECIFICATIONSRecommended Use Domestic, Hotel and Commercial

Vanity Top Material White Matte Solid Surface (15mm)

Vanity Unit Material MDF MR E0 (Medium Density Fibreboard, Moisture Resistant, Rated Emission Level E0)

Vanity Colour Variations

(see page 2)

Textured Woodgrain:

Riven: Light grain texture.

Nuance: Deep wide grain texture.

Ravine: Deep wide grain texture.

Natural Woodgrain:

Matte smooth.

Gloss Silk:

Sheen gloss smooth.

Polyurethane:

White Gloss or Matte, Matte Milton Moon Grey, Black Matte. Smooth.

Interior Finish Graphite Grey on Polyurethane units / Exposed Interior on Woodgrain units.

Tap Hole Availability 0 or 1 Tap Hole

Waste Flexi-Dinger Pop-Up Waste Kit (supplied)

Fixing Bolted/Screwed to the wall by a licensed tradesperson- Fixings not included.

Drawers/Inclusions ADP Premium Soft-Close Drawers with LED.

*Optional Extra Grass Sensomatic Auto-Drawer Open (no handle required)

Concealed internal drawer.

Leatherette Tray Organiser and Tissue Box.

White Solid Surface Handle standard.

Ensembles Shaving Cabinets (900mm, 1200mm, 1500mm).

Mobile unit on castors.

Tall Boy wall hung.

Wall Cabinets (1400mm, 1800mm).

STANDARD SIZES 900mm

Offset

1200mm

Offset

1500mm

Offset

Width (mm) 900 1200 1500

Depth (mm) 500 500 500

Height (mm) 515 515 515

Number of Drawers 2 3 3

page 1 of 7

POLYURETHANE FINISH (Available on Plus Models only)

Smooth

Nuance: Deep wide grain texture

Ravine: Deep wide grain texture

WOODMATT FINISH Smooth matte

NATURAL FINISH Smooth matte

GLOSS SILK OR NATURAL FINISH Smooth glossy / matte

SILK FINISH Smooth & glossy

BlackBlackened Linewood

Raw Birch Ply Gloss White

Smoke ElmChalky Teak

Matte White

Antico Oak

Distressed Wood

Classic Oak

Notaio Walnut

Prime Oak

Cherry RiftwoodTawny Linewood

Polar White

Matte Milton Moon Grey

Domain Espresso Ligna

Riven: Light grain texture

Cherished WoodConcrete Formwood Rural OakSeasoned Oak Sublime TeakWashed Knotty Ash

Parchment

Matte Black

Chalk: Subtle linea texture

Delana Oak Aged Walnut

ASPECT

Gesso Lini Rocco Lini Truffle Lini

page 2 of 7

VANITY UNIT:

150

62268

700

811

005

890

900300

51

005

500216

350

622

110

68 90

621

497

005

500216

350

622

110

68 90

621

497

005

1190

120030051

482.5

150

622

316.5

622101

150

675.5

541

150

550 150

62268

365 900

621

005

1490

1500600

51

005

500216

350

622

110

68 90

621

497

150

550 150

62268

365 900

621

005

1490

1500600

51

005

500216

350

622

110

68 90

621

497

ASPECT

Dimensions are nominal measurements only.

page 3 of 7

SENSOMATIC DRAWER OPTION:(OPTIONAL EXTRA)

100

PLUMBING AREA450mm (W)350mm (H)FROM TOP.

PLUMBING AREA350mm (W)350mm (H)FROM TOP.

POWER AREA200mm (W)200mm (H)FROM BASE.

POWER AREA120mm (W)200mm (H)FROM BASE.

POWER AREA120mm (W)200mm (H)FROM BASE.

Recommended240V Power PointLocation.

Recommended240V Power PointLocation.

Recommended240V Power PointLocation.

OPEN SHELF

OPEN SHELF

100

100

70

660

100

100 100

PLUMBING AREA350mm (W)350mm (H)FROM TOP.

100 100

600 250

566 450 484

350

70

350

Power point240v (not supplied)

Power packand plug (supplied)

Hot and Cold water outlet (if applicable)

ASPECT

Dimensions are nominal measurements only.

page 4 of 7

SHAVING CABINET:

MOBILE: TALL BOY:

873

900

413 482

70

004

130

03263

8

004

150

873

1200

004

374 374 445

70130

03263

8

004

150

873

1500

004

521 451 521

70 70130

03263

8

004

150

285

400

120 120

405

285

407

400

036051

68

289

400

81

405

216252

511

289

407

402

350

28

USB-charge 10-light LED sensor light included.

ASPECT

Dimensions are nominal measurements only.

page 5 of 7

1400

400

1400

134

150

1800

600

1800

200

216

WALL CABINETS:

1400MM:

1800MM:

ASPECT

Dimensions are nominal measurements only.

page 6 of 7

INSTALLATION INSTRUCTIONS

Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference

INSTALLATION INSTRUCTIONS

Prior to installation it is important to unpack & inspect your products to ensure no damage has occurred in transit and that the product IS CORRECT. If damage has occurred, or a visible defect exists, do not proceed with installation and contact supplier IMMEDIATELY.

NO claims for damages / defects will be recognized after installation

1. Check that wall is level (fig 1 and 2) and plumb both vertically and horizontally. If your wall is out of plumb, or is not flat, you will need to pack your vanity so as not to follow the wall. Your vanity must be level, otherwise it will twist and your doors and drawers will be out of alignment.

2. Mark base and back of vanity for drilling to allow for plumbing pipes.

3. Drill holes for pipes with appropriate size hole saw.

4. Position vanity over pipes in correct position. It may be an idea to use a level support / noggin to assist in levelling a wall hung unit and help identify any un-plumb surfaces which may require packing prior to fixing the unit to the wall.

5. Check with spirit level that the vanity unit is completely level. (fig 3 and 4)

6. Fix vanity to wall through back of vanity ensuring the correct screw/dynabolt size is used by the installer to suit the installation situation.

Where studs cannot be located, it is recommended to use toggle bolts or appropriate hollow-wall fixings. Allow enough fixing points, evenly spaced at the top AND bottom of the back panel, to sufficiently hold the particular unit size onto the situation of the installation area. It may be handy to apply some silicone/adhesive to the rear of the unit prior to fixing, this may assist in levelling and fixing the unit to the wall.

7. Adjust doors and drawers if required as there may have been some movement during transportation and installation.

(refer instructions included in unit)

8. Vanity top is then to be siliconed to the top of the cabinet using non Acidic silicone. Apply an unbroken bead of silicone on

all four edges of the top of the vanity and at the back where the top meets the wall. Ensure to seal any visible gaps between

the cabinet and the top with an unbroken bead of silicone.

9. All edges where vanity top and cabinet meet wall and floor are to be sealed with silicone. Gap filler sealant can be used in place of silicone where unit meets tiled surfaces. All areas need to be sealed to prevent water penetration. Materials used for construction of this unit are water resistant NOT water proof. Care must be taken to dry any spillage or leakage of water which may gain access to cabinet. It is recommended that vanities are installed over 300mm from any wet areas such as baths, spas and showers.

10. Where a separate basin is to be fitted it is essential that the basin is fully sealed to the cabinet and top to prevent any water penetration.

11. Waste is not to be over tightened to avoid stress on basin or top. (recommendation for waste to be HAND tight only)

Fig.1 Fig.2 Fig.3 Fig.4

CLEANING RECOMMENDATIONSThis bathroom product should not be cleaned with abrasive materials eg. steel wool/scourers. Do not use any corrosive or abrasive cleaning agents containing acids or scouring agents. To maintain finish on your top, use only a soft cloth or weak solution of non-abrasive detergent. To restore accidental scratches, marks, etc. rub gently with car cutting compound, car polish or household brass/silver cleaner. Bleaches can discolour products and therefore should not be used. Damage caused by any improper treatment or excessive heat is not covered by the product warranty - refer to Warranty Conditions.

ASPECT

page 7 of 7