asic and sensor r&d electronics and sensor technology is central to particle physics research...
TRANSCRIPT
ASIC and Sensor R&D
• Electronics and sensor technology is central to Particle Physics research
• Technology is moving very quickly – sensor arrays of unprecedented size and capabilities are possible• CMS tracker• DES focal plane• CDMS sensor arrays• …
• Electronics with extremely high density and speed can be contemplated
• There are many HEP opportunities, we need to take care to use resources wisely
ASIC/Sensor Projects and Technologies
• Lepton Collider Vertex• X-Ray Imaging• CMS Track Trigger• LHC fast tracker• Digital SIPM
Projects
3D Electronics
Silicon-on-insulator
Device processing(with partners)
Technologies
We have focused on a few technologies which can have significant impact on HEP
Future Challenges• Lepton Collider Vertex Detector - precision
• Superb impact parameter resolution ( 5µm 10µm/(p sin3/2) )• Transparency ( ~0.1% X0 per layer )
• Muon Collider – processing to deal with harsh background environments• 1-3 TeV muon collider on FNAL site• Substantial Huge detector and radiation backgrounds• Fast timing for background rejection
• CLIC – speed and precision• Few ns time resolution
• SLHC – large scale, high speed, harsh environment• 200-400 int/25 ns crossing, track trigger required• Large scale systems• On-detector background rejection
• X-Ray Imaging – speed and density• Variety of challenges – timing
• Intensity frontier• Thin, fast electronics
Building a toolboxto deal with thesechallenges
ILC Vertex
• Much of this work started withILC vertex R&D
• ILC vertex detectors present a particularly difficult challenge• < 5 micron resolution -> small pixels• Mass/layer <10% of LHC detectors -> air cooling, low power• Time stamping
• Then available technologies (CCD, CMOS pixel… ) could not cope• Fermilab began to study 3D integration as a way of integrating
complex functionality in a small pixel
3D• 2 or more layers of active
semiconductor devices that have been thinned, bonded and interconnected to form a “monolithic” circuit.
• Industry is moving toward 3D to improve circuit performance. – Reduce R, L, C for higher
speed– Reduce chip I/O pads– Provide increased functionality– Reduce interconnect power and crosstalk
Provides a set of technologies to thin, bond and interconnect heterogeneous circuits and sensors into a monolithic assembly
IBM/Cornell/UCSB Study – vision of 22 nm 10Tflop 3D chip (2018)
3D Layer Stacking
3D Interconnects
(Tezzaron)
(Ziptronix)
(T-Micro)
(RTI)
Indium
Oxide
Cu-Cu
Cu-Sn
Adhesive
(IZM)
3D For ILCOur initial 3D work was in collaborationwith MIT-LL, aimed at a small pixel for International Linear ColliderOxide bonded tiers of 0.18 mm SOI
• 20 micron pitch pixel, 3 tiers• Time stamping and sparse readout• 64 x 64 pixels
• First iteration had a number of processing issues• Learned a lot about dealing with a leading edge R&D process• Second iteration with more
conservative design works well
VIP2a Results
Digital out (for Inject = 50 mV)
Injectinput
openInt. reset
open Disc.reset, take1st sample
Integrator out
Differential analog out :(Before out) – (After out)
Inject = 50 mVInject = 100 mV
Inject = 200 mV
Discriminator fires
Take 2nd sample
Mux high (read out)
Second iteration test chip
Commercial 3D
Recently we have partnered with Tezzaron Inc. (Naperville Ill) to organize the first commercial 3D multiproject run for HEP.•Based on Tezzaron Cu-Cu bonding•0.13 micron CMOS from Chartered/Global Foundries•6 micron imbedded TSVs•Face-to-face bonding
Multiproject Run
Contributions from 17 institutions• Separate PMOS and
NMOS for MAPS• LHC Pixel• ILC Pixel• X-ray imaging• LHC track triggering
Commercialization
• MOSIS/CMP/CMC (silicon brokers in US, France, and Canada)• Agreement with Tezzaron for commercialization• June 2010 - Announced plan to offer 3D services using
Tezzaron• Working with Fermilab to make HEP 3D efforts available to
the commercial world• Design platform is being developed by Kholdoun Torki at
CMP and the first version is now available• MOSIS, CMP, and CMC will all receive designs• MOSIS will assemble designs into a reticule • Tezzaron will handle the final processing of the 3D frame
(e.g. adding bond pad interface fill, etc.) and submit design to Chartered.
Sensor Integration
• 3D technologies can also be used to integrate sensors to ICs
• Pitches as small as 3 microns, thinned to 25 microns
• Provides for fully active sensors as large as 6” (or 8” wafer) based on tiled ROICs
• We have also developed a thinning and laser-based annealing process for low leakage sensors as thin as 50 m
FPIX Chip on FNAL/MIT-LL Sensor
FPIX/Sensor Tests
• BTeV FPIX bonded to MIT-LL sensor
• Thinned to 100 m• Noise studies• Laser, x-ray, beam tests• Good, low cap. bond
Bonding process for Tezzaron chips to BNL sensors
SOI R&D
• Silicon on insulator devices with high resistivity detector handle wafers - OKI and American Semiconductor (ASI)
• Truly integrated sensor/electronics• Last run demonstrated integration of SOI electronics with high
resistivity substrate on 8” wafers
High resistivitySilicon wafer,Thinned to 50-100 microns
Minimal interconnects, low node capacitance not to scale
Backside implanted and laser annealed after processing
Backgate effects• The potential of the substrate can change the fields at the top transistor and
affect performance – “backgate”• Backgate effects significant in OKI process and limit bias that can be applied • Digital-analog coupling can also destroy performance
• FNAL suggested process changes to OKI to fix this• Initial tests show the chips are not significantly affected by back potential
This well separates digital circuitsfrom sensor substrate and preventsback gating effects
This well collects the charge
Patent application underdiscussion
SOI Devices
MAMBO x-ray imaging counting pixel chip
• Maximum counting rate ~ 1 MHz• Each pixel: CSA, CR-RC2 shaper,
discriminator + 12 bit binary counter
47 mm
MAMBO II pixel layout
13 diodesin parallel connection
X-Ray Correlation Spectroscopy
CMS Track Trigger
• At SLHC standard trigger menu saturates
• Track-based triggering needed to explore new physics
We are designing a level 1 track trigger for CMS II• >150 m2 of silicon, >900 M channels• 40 Mhz crossings, 200 interactions/crossing, • 2.75x1013 bits/second of hit data in the tracker• Process this information to make a decision on whether an
event is “interesting”• Can only record ~1/400• Need to make a decision on the event within 3.2 ms
• Filter out data from low momentum tracks-reduce data by >20
• Curvature information in 4T field can be analyzed locally an a 3D chip – minimal data transfer and associated power• Stacked layers ~ 1mm apart• Local processing and local hit
correlation• Exploring the concept for muon
collider as well
Track Trigger Projects
• Large area arrays (see later)• Small demonstrator module
• Interposer• VICTR Chip• Sensors
• Full Module• Interposer development• High speed, fault tolerant,
data flow design• Mechanical supports• Simulation
Shor
t Str
ip T
ier
Long
Str
ip T
ier
Fast Trigger/Tracker• Content Addressable Memory stack (CAM) can simultaneously
compare external patterns to stored templates.• Very fast pattern recognition – at the cost of silicon area
• CAMs were used in the CDF SVT• Similar concept being developed for ATLAS FTK
• FNAL is working on custom ASIC design
Fast Tracker• 3D concept can also be used to correlate hits in a multilayer CAM
stack• Extending the CAM concept to 3D improves density, speed, and
power consumption
Large Area Arrays• The CMS track trigger requires 10x10 cm modules with ~25
chips/module• Bonding yield may be ~ 95%• Overall yield (.95)25 ~ 0
• Use active edge silicon detector to use known good sensor/detector die – use high yield bump bonds to connect to PCB
• Saw cut edges on normal silicon are sources of leakage current – stay 3x depth away to limit leakage current - creates dead areas
• Ion etching used in 3D processes can produce an “atomically smooth” edge – small leakage and sensitive to within a few microns of the edge
ROICDBI
sensor
SOI bond
handle
10m2m
200m
1m
500m
cutTSV wafer
DBI
sensor
SOI bond
etch
ROICDBI
sensor
Active edge
Digital SIPMs
• Geiger mode avalanche photodiodes (SIPMs) are an emerging replacement for the phototube
• They are inherently digital – but read out as analog sum of hit pixels
• Access to digital information using 3D through-silicon-vias would allow• Active quenching – faster, less after-pulsing• Digital hit counting• Position resolution• Pixel masking• Precise timing• Good QE
Digital SIPM Development
1. Establish bonding technology (underway)2. Work with SIPM fabricator to obtain full wafers
• Use vias inserted post fabrication (via last) or pre fabrication (via first)
3. Design electronics4. Build and test
TSV
R&D Collaborations (a partial list)• Industry
• Tezzaron• Ziptronix• OKI• American Semiconductor• Vega Wave
• Laboratories• SLAC• BNL• LBL• CERN• MIT-LL• KEK• Sandia - beginning
• Universities• Cornell (laser anneal, large
area arrays, simulation, testing)
• Brown• Northwestern• UC Davis• North Carolina• + 17 in 3D collaboration
I read these guidelines from Erik after I prepared the talk• A short overview of the various ASIC and sensor projects
• Not so short• How these projects will extend into the future. Do you foresee problems with
resources?• ILC work morphing into other things – other projects have clear paths• Physicist and testing resources are scarce for all projects
• What are the best avenues for new silicon R&D to pursue. Do you need new facilities?• There are many opportunities – the hard part is matching our stomachs to
our eyes. For us 3D is the enabling common thread.• Modern test hardware and design software is crucial and needs continuing
investment• Technology, once developed, needs to be applied – a difficult problem with
decades between experiments• How does this tie in with the national picture? Are we falling behind, or breaking
new ground?• We are real leaders in this field, but we need to collaborate with commercial
firms, universities, and other labs that all have unique capabilities
Frontiers
Precision frontier
ProcessingFrontier
ScaleFrontier
This is obviously a shameless attempt to co-opt the Quantum Universe – anddoesn’t really work – but we are all friends