ashis
TRANSCRIPT
GUIDED BY:Prof. S.S Singh
PRESENTED BY :ASHIS KUMAR JENAREGD NO-1101304073
ANSHUL NISHANT KANDULNAREDG NO-1101304072
MECHANICAL ENGINEERING7th sem
ELECTRO DISCHARGE MAHINE
GITAM
CONTENT OBJECTIVES INTRODUCTION EVOLUTION IN EDM MACHINES TYPES OF EDM CONSTRUCTION WORKING PRINCIPLE TOOL MATERIAL MEDIUM MACHINING RATIO PROCESS PARAMETERS ADVANTAGES DISADVANTAGES APPLICATIONS REFERENCE
OBJECTIVES
TO study about Electro discharge machine.
To give small introduction about the types of electro discharge machining.
To study the process parameter of EDM machine.
INTRODUCTION The history of EDM itself begins in 1943, with the invention of its
principle by Russian scientists Boris and Natalya Lazarenko in
Moscow.
Electro Discharge Machining (EDM) is an electro-thermal non-
traditional machining process, where electrical energy is used to
generate electrical spark and material removal mainly occurs due to
thermal energy of the spark.
Electro discharge machining is also called
as spark machining/spark erosion machining.
TYPES
There are two type‘s of EDM machining process
Die-Sinking EDM ( The Ram Type ):
• In the die - sinker EDM Machining process, two metal parts are
submerged in an insulating liquid and are connected to a source of
current . When the current is switched on, an electric tension is
created between the two metal parts and if the two parts are brought
together to within a fraction of an inch, the electrical tension is
discharged and a spark jumps across. Where it strikes, the metal is
heated up so much that it melts.
• It is also called as cavity type EDM or volume EDM .
Wire-cut EDM: In this process a moving metalic wire made off up copper ,brass and
zinc coated brass wire is acting as electrode is used to cut complex outlines and find the detail in the required work piece.
CONSTRUCTION The setup consist for an EDM are a power supply source ,a dielectric
medium , workpiece ,tool, servo control, speed reduction gear box, a rack and pinion arrangement or other suitable mechanism for tool feed.
In EDM the tool is connected to the negative terminal of DC power
supply act as cathode and the workpiece is connected to positive
terminal of DC power supply, act as anode.
A gap is maintained between the tool and the work piece which is
called as spark gap , the spark gap is usually varies from 0.005mm to
0.05mm.The spark gap is feed by dielectric which brake down when a
proper dc voltage is applied between the tool and the work piece.
when a circuit voltage of 50 to 450v is applied then the electron starts flowing from cathode due to which the gap ionised.
.
WORKING PRINCIPLE
So there is drop in resistance and discharge of electric energy results in electrical brake down . so large amount of spark is generated.
The spark discharges heat to the work piece material with considerable force and velocity and results in development of high temperature around 10000`c.
These forces the work piece to melt and a portion of it is vaporized , these portion is taken away from the spark gap by the flow of dielectric through it.
TOOL MATERIAL
The commonly used tool materials are brass, copper and some other
materials like cast iron , tungsten ,graphite , and alloys of silver etc.
Thus the basic characteristics of electrode materials are:
High electrical conductivity.
• High thermal conductivity .
High density.
High melting point.
Cheap cost.
The tool should be made of
Same material as the work piece.
In EDM material removal generally takes place due to thermal
evaporation and melting .The main aim of providing dielectric is to
maintain a oxygen free environment and it should have strong
dielectric resistance so that it does not breakdown so easily.
Dielectric is used as medium in EDM. The commonly used dielectrics
are paraffin or some light oil like transformer oil or kerosene.
MEDIUM
MACHINING RATIO We know
machining ratio=material removal rate / tool wear• The material removal rate of the work piece is the volume of the material
removed per minute.
So machining ratio depends upon the melting temp. of tool and work piece If melting temp. of tool = melting temp. of work piece then machining ratio will
be 1 to 2. If melting temp. of tool > melting temp. of work piece then machining ratio will
be 8 to 10. If melting temperature of tool < melting temperature of work piece then
machining ratio will be 0.1 to 0.3.
PROCESS PARAMETERS There are two types of process parameters for EDM. Electrical parameters: Pulse Duration.
Pulse Interval.
Electrode gap (spark gap). Polarity.
Non electrical parameters: Rotation of Tool Electrode Tool material (Electrode) Tool Geometry
ADVANTAGES
The deep hole can be produced.
Material removal cost is very low.
The operation is noiseless.
The machined surface are free of stress.
Any material that is electrically conductive can be cut using the EDM process .
Complex dies sections and moulds can be produced accurately, faster, and at
lower costs.
Hardened work pieces can be machined easily.
DISADVANTAGES
The work piece material must be electric conductive.
Perfect square corners cannot be produced by EDM.
It is only used for machining of small work pieces.
Dielectric vapour can be dangerous.
The energy required for the operation is more than that of the
conventional process and hence will be more expensive.
APPLICATION
in the aerospace, automobile and electronics industries in which
production quantities are relatively low.
It is used to machine extremely hard materials that are difficult to
machine like alloys, tool steels, tungsten carbides etc .
It is used for forging, extrusion, wire drawing, thread cutting .
It is used for internal thread cutting and helical gear cutting .
It is used for machining sharp edges .
Ceramic materials that are difficult to machine can be machined by the
EDM machining process.
REFERENCE
International Journal of Engineering Science and Technology Vol. 2(6),
2010, 2172-2191.
International Journal of Modern Engineering Research (IJMER) .
REPUBLIC OF IRAQ. MINISTRY OF HIGHER EDUCATION &SCIENTIFIC
RESEARCH. UNIVERSITY OF TECHNOLOGY PRODUCTION & METALLURGY
ENG. DEP. CONSIDEORATION OF GRADUATIN.
Version 2 ME, IIT Kharagpur .
Mohan, B., Rajadurai, A., Satyanarayana, K. G Journal of Materials Processing
Technology