armored riot control

7/29/2019 Armored Riot Control

1/12

Based on a Ford

F-750

ARMORED RIOT CONTROL WATER CANNON TRUCK


2/12

Page 1Tel: +1.703.471.0002 Fax: +1.703.471.0202 www.alpineco.com [email protected]

Engine:

Transmission:

Power:

Tires:

Level A9 (B6), to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51

Level A10 (NIJ IV)

to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51 rounds

ARMORED RIOT CONTROL / WATER CANNON TRUCK

FORD F-750 (Basic Specs)

5.9 L. Cummins Diesel

5-Speed Automatic

215 HP @2300 RPM 520 lb/ft @1600RPMTires:

Goodyear 10R22.5 With Run Flat Inserts

Height:

Length:

Wheelbase:

Width:

117 in. (298 cm.)

312 in. (792 cm.)

158 in. (401 cm.)

93 in. (236 cm.)
http://www.alpineco.com/mailto:[email protected]:[email protected]:[email protected]://www.alpineco.com/


3/12


ARMOR SPECIFICATIONS

Protection on all sides to Level A10

Protection against high power rifles such as: 7.62x39, 5.56x45, .03-06 and 7.62x51 rounds

OPAQUE (AR 500 Steel): 0.50 in thick

TRANSPARENT (Glass/Polycarbonate): 55 mm thick

Seating- two seats up front, bench seating for 4 in rear, 2" padded seat and backs

Special LED Red and Blue lights

White LED dome lights for the Interior

Armored Dual battery compartment

Running boards with grab handles

Rear door opening 6', 8" long and 33" wide

Insulation on all walls and ceiling (2")

Recording equipment for all cameras

Under seat compartments

3 Outside storage cabinets

Removable Plow Control

Revolving Water Cannon

Revolving Camera on rooftop

2 Gun Ports on each side of the front cabin

P/A System with siren


Level A10 (NIJ IV)




4/12


INSTRUCTIONS

Operations of Stryker

Using the remote control, turn on the light by depressing the on/off button

With the 4-way arrows on the remote control, rotate your light to the desired location.

Depending upon conditions, the wireless remote may be used up to 100 feet from the Stryker.

The speed of the light rotation can be controlled by depressing the fast/slow button one timeand by depressing it again to restore the original speed.

The spotlight should not be turned on when the snap on lens (rockguard) is attached.

BULB REPLACEMENT

The GolightStryker utilizes a Philips9011 bulb

IMPORTANT INFORMATION

This GolightStryker is a radio transmitter and receiver operating at 433mhz. Whenever the light

is on, the internally mounted antenna sends out and receives radio frequency (RF) energy.

PROGRAMMABLE REMOTE INSTRUCTIONS

The GolightStryker is controlled with a programmable remote with 6561 different channels.This feature allows you freedom to change the channel

selection, & the receiver relearns the new selection.

Level A9 (B6), to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51Level A9 (B6), to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51

Level A10 (NIJ IV)



GO LIGHTS

* Click here to view PDF link
http://www.alpineco.com/mailto:[email protected]:[email protected]://www.alpineco.com/inventory/riotcontrol/pdf/go-light-stryker_inst.pdfhttp://www.alpineco.com/inventory/riotcontrol/pdf/go-light-stryker_inst.pdfmailto:[email protected]://www.alpineco.com/


5/12


RED

BLUE STROBE LIGHTS

Double, Red/Blue Strobe, Lighter Plug-in. The RVM directional warning device combines the best

warning signal & easiest installation

Inside the dashboard the ON/OFF Strobe Lights Button


Level A10 (NIJ IV)



RED/BLUE LIGHTS


6/12Page 5Tel: +1.703.471.0002 Fax: +1.703.471.0202 www.alpineco.com [email protected]

TOUCH PAD PLOW CONTROL

Plow Is made out of 1/4'" armor steel.

Intuitive design with large illuminated raised rubber indicator arrows for ease of use.

Convenient indicator lights make it simple to see the status of the plow.

Only Up and Down Arrows.

Level A9 (B6), to stop 7.62 x 39, 5.56 x 45, and 7.62 x 51Level A10 (NIJ IV)



PLOW CONTROLS



PUBLIC ADRESS SYSTEM WITH MULTI-MODE SIREN

Two manual functions allow for additional siren tone choices when you need it the most.

PTT (push to talk) switch on microphone overrides all siren functions.

Combination On/Off and horn ring transfer switch.

Pre-wired unidirectional microphone.

Optional plug-in microphone with volume control knob.

Adjustable preset microphone volume.

Adjustable preset radio repeat volume.

Input polarity protection.

Output short circuit protection.

External spade-type fuse.

Bi-polarity horn/ring control activation.

"Aux Enable" activates

Siren tones via input (slide switch, power controls or relay-to-ground connection).

Quick disconnect plug for ease of service or replacement.

Adjustable bail bracket allows the mounting of the siren in a variety of positions.

Complements all Whelen's under dash products.

Backward compatible to the original 295HF100 and

WS2100 Series connector.

Optional 24 volt DC model available, contact factory.

DIMENSIONS

Height: 63mmx Width: 152mmx Depth: 138mm




CONTROL BOX
http://www.alpineco.com/mailto:[email protected]:[email protected]://www.alpineco.com/inventory/riotcontrol/pdf/pa-system.pdfmailto:[email protected]://www.alpineco.com/



COLOR CCD IR BULLET CAMERA #1, #3, #4

Camera #1 Right Side

Camera #3 Left Side

Camera #4 Rear View

Night Vision, High Resolution

COLOR CCD IR BULLET CAMERA #2

Camera #2 Front View

Mini 10x weatherproof PTZ Camera

WTX-1200A KEYBOARD CONTROLS

Pan/Tilt Operating Di : 4,000ft (1,092m)

on 24 AWG wire

3-Axis, vector solving, with twisting,

return-to-center head

THIN FILM TRANSISTOR (TFT)

LIQUID CRYSTAL DISPLAY (LCD) MONITOR




CAMERA SYSTEM
http://www.alpineco.com/mailto:[email protected]:[email protected]://www.alpineco.com/inventory/riotcontrol/pdf/bullet-camera.pdfhttp://www.alpineco.com/inventory/riotcontrol/pdf/mini-ptz-camera.pdfhttp://www.alpineco.com/inventory/riotcontrol/pdf/control-joystick.pdfhttp://www.alpineco.com/inventory/riotcontrol/pdf/control-joystick.pdfhttp://www.alpineco.com/inventory/riotcontrol/pdf/mini-ptz-camera.pdfhttp://www.alpineco.com/inventory/riotcontrol/pdf/bullet-camera.pdfmailto:[email protected]://www.alpineco.com/






WATER CANNON
http://www.alpineco.com/mailto:[email protected]:[email protected]://www.alpineco.com/inventory/riotcontrol/pdf/8494-Sidewinder-Instructions.pdfmailto:[email protected]://www.alpineco.com/






CONTROL BOX
http://www.alpineco.com/mailto:[email protected]:[email protected]://www.alpineco.com/inventory/riotcontrol/video/controls/controls.htmlmailto:[email protected]://www.alpineco.com/



HOW TO OPERATE WATER CANNON CONTROLS

1.

Turn on Button on Box Control

2. Lower pressure

3. Start Engine Pump

4. Hold button to add pressure till desired distance and pressure shows

5. Use joystick to move cannon

6.

To use Dye Push trigger on joystick

7.

Push Button to Spread/Fan Effect on Nozzle




CONTROL BOX

1

2

3

4

5

6

7
http://www.alpineco.com/mailto:[email protected]:[email protected]://www.alpineco.com/inventory/riotcontrol/video/controls/controls.htmlhttp://www.alpineco.com/inventory/riotcontrol/video/controls/controls.htmlmailto:[email protected]://www.alpineco.com/


12/12Tel: +1.703.471.0002 Fax: +1.703.471.0202 www.alpineco.com [email protected]

COMPOSITE RUN FLAT (CRF) INSTALLATION

Ensure the CRF properly fits the wheel before mounting the tire

Clean wheel and install metal valve supplied.

Use a soft cloth or brush to apply supplied lubricant to evenly inside crown of the tire, around entire circumference.

With flanges and washers facing up, position CRF arcs against wheel and confirm they are properly mated to wheel profile.

Install bolts to ensure CRF is secure to the wheel drop center. Bolts should be tightened to 30 +/- 5 ft.lbs

If needed place the steel mounting rods in the holes on each side of the CRF joint.

Slip adjustment band over rods and pull outward to bring arcs together.

Attempt to rotate CRF around wheel to assure it is snug.

For additional tightness, unfasten set screw on washer, rotate one or both washers 180 as needed. Re-install set screw.

INSTALLATION IN TIRE

Insert arcs into the tire with the flanges and washers facing up.

Apply supplied loctite to one bolt. Connect arcs loosely with one bolt

Fit inboard tire bead on wheel and allow CRF to move into wheels drop center

With outboard tire bead above the wheel flange, place steel mounting rods vertically in holes on each side of CRF joint.

Rotate CRF until the joint is centered over the valve

Slip adjustment band over mounting rods. Laterally spread the rods at top closing the CRF.

Apply loctite on the remaining bolt and tighten ALL bolts to 30 +/- 5 ft.lbs

Secure mechanical lock over all connection bolts. Attached with #2 phillips head screw driver.

Mount outer tire bead and inflate to manufacturers recommended pressure for load carried.

Page 11




RUN FLAT INSTALLATION
http://www.alpineco.com/mailto:[email protected]:[email protected]://www.alpineco.com/inventory/riotcontrol/pdf/HutchinsonCRFInstall.pdfmailto:[email protected]://www.alpineco.com/

armored riot control

Documents