ARMAAX AUTO PVT LTD

ARMAAX AUTO PVT.LTD. Company started its humble operations in the year 1974 atMalad, Mumbai with the manufacture of small components of Tractors and Automobiles for M/s Mahindra & Mahindra. Over the past years ARMAAX AUTO has developed itself as a major vendor of Mahindra & Mahindra for supply of major parts of Tractors for their Farm Equipment Division. Also we are serve for Godrej(Engineering division),Mahindra-international at pune, Larsen & turbo ltd.Dana India Pvt Ltd

ARMAAX AUTO now has the finest state of the art infrastructure for manufacturing for Sheet Metal Stampings, Welded Sub Assemblies, Front Sale Assemblies, Press Shop Tooling and Jigs & Fixtures.

ARMAAX AUTO PVT.LTD. now has under its banner the following units:- 1) Maharashtra Engineering at Kolhapur (An ISO 9001 : 2000 certified company).

2) Ameya Engineering Works at Vasai (An ISO 9001 : 2000 certified company).3) Axelo Industries at Vasai (An ISO 9001 : 2000 certified company).4) R. K. Engineering Works at Malad, Mumbai.5) R. K. Agro Industries at Nagpur.6) R. K. Tooling & Pressing Pvt. Ltd. at Vasai.7) R. K. Motors at Malad, Mumbai..

ARMAAX Group launched its first Electric Bicycle and Three Wheeler at the beginning of the year 2003. The initial sale of the products and the market reports thereafter gave a very satisfactory report. We are developing our product for Indian market & specially for Indian road

With its revamped operations in April 2006, the ARMAAX AUTO is now ready to spread its dealer network of E-Bicycles, All-India, with prompt after-sales service to the end customer. Products marketed by R. K. Motors are as follows:-

Matrix Series:-Matrix-SS,Matrix –Super,Matrix-A,Matrix-1,Matrix-Super Plus, Matrix-Indi Plus,R.K.EBIKE-CHIC.

Three Wheeler Goods Carrier, Model :- Dhanashree. & Dhanashree Deluxe. Power Tiller, Model:- 12 H.P. and 15.. Accessories for Power Tiller such as Single and Double Furrow Plough, Disk

Plough, Sprinklers and other similar accessories for agricultural purposes.

SPECIFICATION

MODEL: MATRIX SUPER

AVERAGE: <=80kms.

Speed: <=25-30 kms

Motor: Gear motor

Battery: 48 Volt/20 amp.

Charging Time: 8 hrs.

Load Capacity:120 Kg.

Tyre Size: 16*3

SPECIFICATION

MODEL: MATRIX 1

AVERAGE: <=100kms.

Speed: <=25-30 kms

Motor: 240 Watt

Battery: 48 Volt/20 amp.

Charging Time: 8 hrs.

Load Capacity:120 Kg.

Tyre Size: 18 *2.5

SPECIFICATION

MODEL: MATRIX INDI-plus

AVERAGE: <=80 kms.

Speed: <=25kms

Motor: Hub motor

Watts: 240 watts

Volts: 48 V

SPECIFICATION

MODEL: MATRIX SS

AVERAGE: <=80kms.

Speed: <=25-30 kms

Motor: Gear motor

Battery: 48 Volt/20 amp.

Charging Time: 8 hrs.

Load Capacity:120 Kg.

Tyre Size : 16*3

SPECIFICATION

MODEL: MATRIX SUPER

PLUS 1

AVERAGE: <=80kms.

Speed: <=35-40 kms

Motor: 850 Watts

Battery: 48 Volt/20 amp.

Charging Time: 8 hrs.

Load Capacity:120 Kg.

SPECIFICATION

MODEL: MATRIX A

AVERAGE: <=50 kms.

Speed: <=25-30 kms

Motor: 240 Watts.

Battery: 48 Volt/20 amp.

Charging Time: 6 hrs.

Load Capacity:100 Kg.

The face of auto industry, that was redefined with the invention of fuel-efficient four-stroke engine technology, is all set to see dawn of a new era in two-wheeler industry. It's not petrol or diesel or any other fuel, but it's electricity that have initiated a revolution in two-wheeler industry in India.

Indian two-wheeler industry has embraced the new concept of Electric Bikes and Scooters that are very popular mode of personal transport in the developed countries like America, Japan and China. With the rising cost of fuel at International and national level, increasing levels of pollution and congestion in transport system specially in Urban areas, higher running and maintenance cost of vehicle, the electrically charged bikes or scooters have very bright future in area of personal transportation

What is Electric Vehicle

An Electric Bike or Scooter is a battery operated vehicle that is very economical with low maintenance cost and zero pollution. Electric two wheelers use the electrical technology of rechargeable battery that converts the electrical energy into mechanical energy. The battery of an EV can be charged easily using a power connection.

Features of Electric Bikes and Scooters

Electric bikes or scooters, light in weight, trendy, efficient and eco-friendly, are becoming potent alternative to the conventional two-wheelers and the Electric two-wheeler industry in India is developing at rapid speed. Have a look at the unavoidable advantages of Electric Bikes and Scooters :

License and registration is not required for E Bikes and Scooters.

Electric two wheelers run on re-chargeable battery and uses electricity as fuel in place of conventional Petrol/Diesel.

E Bikes and Scooters can beat the rising prices of Petrol/Diesel.

Simple design, light weight and economical Electric vehicles are very low in running and maintenance cost.

With the ease of handling, Electric two wheelers saves the commuting time in congested roads specially in urban areas.

Electric vehicles are more efficient in terms of generating usable energy from their electric engine's battery in comparison to the regular fuel conversion. In this way E Bikes and Scooters are innovative and efficient mode of personal transport.

Electric bikes or scooters use electricity therefore no emission of harmful gases like Carbon dioxide (CO2) or Nitrogen dioxide (NO2).

Major Components of an Electric Bike or Scooter

ELECTRIC HUB MOTOR :-to drive the rear wheel directly and there are two types of Electric Hub Motor i.e. DC Brush Motor and DC Brush less motor having two basic parts namely Permanent Magnet Stator and Wound Rotor.

ELECTRONIC MOTOR CONTROLLER:- is the central controlling unit of any Electric two wheeler provides electric power to the motor based on inputs from the accelerator.

ELECTRONIC ACCELERATOR :-sends electronic signals to the Electronic Motor Controller to maneuver the bike or scooter.

BATTERY PACK:- is like the fuel tank of E Bike or Scooter. There are different kinds of batteries like Lead Acid, Nickel Metal Hydrate (Ni-MH), Lithium, etc. that are used for supplying energy.

BATTERY CHARGER:- is used to charge the battery pack of E Bikes or Scooters, just like a mobile phone or a laptop. Some battery chargers are in-built and some are separate that carried always on the move. The charger converts an AC supply to DC to store power in the battery and it can be used with any normal domestic AC plug point. This makes charging of battery pack easy and convenient

PARTICULAR PETROL-SCOOTER E-BICYCLE

RANGE 50/PER-LIT 100/PER-CHARGE

COST/100KMS 122(2lit) 7.00 PER KM

COST OF FUEL:-S./KM1.22 PAISE PER KM 0.07 PAISE PER KM

COST OF FUEL-POWER OVER 30,000KMS RS. 36600 2100

SERVICE & MAINTENANCE 9000 1000

BATTERY REPLACEMENT COST(AFTER 300 CYCLE CHARGE) N-A 6700

TOTAL EXPENSES 45600 9800

COST OF VEHICLE(*EX-SHOWROOM) 45000 25000

REGISTRATION 3500 N-A

INSURANCE 1000 550(IF REQUIRES)

HANDLING 200 80

TOTAL INVESTMENT ON VEHICLE 49700 25630

TOTAL INVESTMENT + RUNNING COST 86300 35430

TOTAL SAVINGS!50870

SPECIFICATION

MODEL: Three-Wheeler

AVERAGE: <=50 kms.(un-load)

<=35 kms( With Load)

Speed: <=25-30 kms

Motor: 240 Watts.

Battery: 48 Volt/20 amp.

Charging Time: 6 hrs.

Load Capacity:50 Kg.

ENGINEC.CStartingWheel-baseLoad-Cap.Break

Petrol,4-stroke125Kick/Electric1800 MM300 kgs*Mechanical

Engine 6.5 HP (Petrol- 4-Stroke)

Stroke 4 Stroke

CC 196 cc,DI

Fuel Capacity 3.6 Litre

Working Width 30-50-85 Cm.

Working Depth 35 Cm.

Weight 55 Kgs.

Dimension 42 cm.*78cm.*82cm.

RPM. 3600

Displacement 163 CC.

Driving Mode BeltGear Shifting (Speed) 1-Forward,1-Reverse

Starting System recoilStandard Accessaries 2 Back Wheels

2 Group Big Blades

PP Plastic Outerstreet

Working Capacity For 1 Acre-4 hrs.

(For 1 Acre require 4 Litre Petroll)

Adjustable For 2 Ft.,3Ft,4 Ft.

OUR STRENGTH Technocrat-CMD Sheet Metal & Plastic Components Design to Supply under

one roof. Long Term Attachment with M&M-33 Years Investment for up gradation of plant for continuous

improvement. All Group companies ISO certified. Successful implementation of Kan Ban. Rated as one the Best Supplier for Prototyping [Fast, Cost

effective, Flexible] Well equipped Tool-Room to support Fast, timely

development of Product. In house Design facility “Unigraphics” Ability & willingness to Invest. Heavy duty stamping & fabrication facility. State of the Art powder coating facility. Latest version of Injection molding Machines. Already in Export to US OEMS

Let us strengthen the

Association

Thank You