argox manual

7/22/2019 Argox Manual

http://slidepdf.com/reader/full/argox-manual 1/75

1

Compact Printer Series - User ‟s Manual

COMPACT PRINTER SERIES

USER’S MANUAL

CP-2140 / CP-2140Z / CP-2140E

CP-3140

Website: http://www.argox.com

http://www.argox.com/

http://www.argox.com/



2


Table of Contents

Introduction ....................................................................... 4 Proprietary Statement ................................................... 4 Product Improvements ................................................. 4 FCC Compliance Statement ......................................... 4 Liability Disclaimer ........................................................ 4

Getting Started .................................................................. 6 Unpacking Printer ......................................................... 6

Package Contents .................................................... 7 Printer Overview ........................................................... 8

Front View: CP-2140, CP-2140Z, CP-2140E,

CP-3140 ............................................................... 8 Rear View: CP-2140, CP-2140Z, CP-3140 .............. 9 Rear View: CP-2140E .............................................. 9 Interior View I ......................................................... 10 Interior View II ........................................................ 11

Attaching Power ......................................................... 12 Loading Media ............................................................ 14 Preparing Media ..................................................... 14 Placing Media Roll ................................................. 14

Setting Media Type ..................................................... 19 Loading Ribbon .......................................................... 20

Preparing Ribbon ................................................... 20 Placing Ribbon Rolls .............................................. 21

Cutter Option .............................................................. 26 Installing Cutter ...................................................... 27

Printer Operations .......................................................... 32 Printing Media Calibration & Configuration ................. 32

Steps to Start Media Calibration & Configuration ... 32 Sample of Printer Configuration Label ................... 33



3


Resetting Printer to Factory Defaults .......................... 35 Printer Controls and Indicators ................................... 36 Troubleshooting by LED Indicators Diagnosis ............ 39 Miscellaneous ............................................................. 42 Recovery ..................................................................... 43

Communications ............................................................. 44 Interfaces and Requirements ...................................... 44

USB Interface Requirements .................................. 44 Serial (RS-232) Interface Requirements ................. 45 Parallel Interface Requirements.............................. 45 Serial and Parallel Cabling Requirements .............. 45 Ethernet 10/100 Internal Printer Server Option ....... 46 Ethernet Module Status Indicators .......................... 46

Communicating with the Printer .................................. 47 Installing a Plug and Play printer driver (for USB only)

........................................................................... 47 Installing a Printer Driver (for other interfaces except

USB) ................................................................... 53 Caring for Your Printer .................................................... 60

Print Head Maintenance Guide ................................... 60 Cleaning Interval ..................................................... 60 Cleaning Material .................................................... 60 Cleaning Direction .................................................. 61

Product Specification ..................................................... 62 General Specification .................................................. 62 Fonts, Barcodes, and Graphics Specification ............. 64

Printer Programming Language PPLA.................... 65 Printer Programming Language PPLB.................... 66 Printer Programming Language PPLZ .................... 67

Interface Specification ................................................. 69 USB Interface ......................................................... 69



4


Serial Interface ....................................................... 70 Parallel (Centronics) Interface ................................ 71 Ethernet Interface ................................................... 71



4


Introduction

Proprietary StatementThis manual contains proprietary information of Argox Information Co., Ltd. It is

intended solely for the information and use of parties operating and maintaining theequipment described herein. Such proprietary information may not be used,

reproduced, or disclosed to any other parties for any other purpose without the

expressed written permission of Argox Information Co., Ltd.

Product ImprovementsContinuous improvement of products is a policy of Argox Information Co., Ltd. All

specifications and signs are subject to change without notice.

FCC Compliance StatementThis equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that the

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct the

interference by the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into a different outlet on a different circuit.

Consult the dealer or an experience Radio/TV technician for help.

This unit was tested with shielded cables on the peripheral devices. Shielded cables

must be used with the unit to insure compliance. The user is cautioned that any

changes or modifications not expressly approved by Argox Information Co., Ltd.could void the user‟s authority to operate the equipment.

Liability Disclaimer Argox Information Co., Ltd. takes steps to assure that the company‟s published

engineering specifications and manuals are correct; however, errors do occur. Argox

Information Co., Ltd. reserves the right to correct any such errors and disclaims any

resulting liability. In no event shall Argox Information Co., Ltd. or anyone else

involved in the creation, production, or delivery of the accompanying product

(including hardware and software) be liable for any damages whatsoever (including,



5


without limitation, damages for loss of business profits, business interruption, loss of

business information, or other pecuniary loss) arising out of the use of or the results

of use of or inability to use such product, even if Argox Information Co., Ltd. has been

advised of the possibility of such damages.

CAUTION:

Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.



6


Getting Started

Congratulations on choosing CP compact printer series, made by

Argox Information Co., a leader in the world-wide barcode industry.

CP-2140, CP-2140Z, CP-2140E, and CP-3140 are ideally designed

to easily bring more efficiency for your business. This manual will help

you get to know your new printer and provide sufficient information

needed.

Unpacking Printer

After receiving your printer, please check for possible shipping

damage:

Inspect the outside of both the box and the printer for possible

damage.

1. Open the top cover of the printer to see if all parts are in order.

2. Check whether you have received the following accessories

together with the printer. If there is any item missing, please

contact your local dealer.

Note: If shipping damage has been discovered, contact your

shipping company immediately to file a claim.



7


Package Contents

Quick Installation Guide

CD ROM (Documentation & Software)

Power Cord

Media Hanger & Media Shields

Printer

Power Supply

USB cable

Ribbon Core Adaptors

1” ID Core for Ribbon

Quick Installation

Guide

Printer

CD ROM

Power Supply

Power Cord

Media Hanger &

Media Shields Ribbon Core

Adaptors

USB cable

1” ID Core for Ribbon



8


Printer Overview

Front View: CP-2140, CP-2140Z, CP-2140E, CP-3140

Feed Button

Power LED

Ready LED

Top Cover



9


Rear View: CP-2140, CP-2140Z, CP-3140

Rear View: CP-2140E

Power Switch

Parallel Port USB Power Jack

RS232 Serial

Power Switch

EthernetUSB Power Jack

RS232 Serial



10


Interior View I

Module Release Latch

Media Shields

Ribbon

Pick-up

Holder

Media Hanger

PUSH



11


Interior View II

Feed Button

Power LED

Ready LED

Platen Roller

Reflective sensor

Top Cover

Print Head

Front Cover

Media Guides

RibbonSupply

Holder

Transmissive

Sensor

Head-Open Sensor

Media Shaft



12


Attaching Power

1. Make sure the printer‟s power switch is in the off position (down).

2. Insert the AC power cord into the power supply.3. Insert the power supply‟s power connector into the printer‟s power

jack.

4. Plug the other end of the power cord into an appropriate grounded

AC electrical outlet.

CP-2140, CP-2140Z, CP-3140

Power Supply

Warning:

Do not operate the printer and power supply in an area where they

might get wet.

Power CordPower

Connector

Power Jack



13


CP-2140E

Power SupplyPower Cord

Power

Connector

Power Jack



14


Loading Media

Preparing Media

The inside wound or outside wound media rolls can be loaded into

the printer in the same way. In case media roll may become dirty or

dusty during shipment, handling, or storage, firstly remove the outside

length of media, which helps to avoid dragging adhesive or dirty

media between the print head and platen roller. When loading media,

it must be placed onto the media hangers.

Placing Media Roll

1. Open Top Cover of the printer.

Top Cover



15


2. Put the Media Hanger through media supply roll, and then

centrally align with the two Media Shields to closely lean against

the media supply roll.

3. Locate the media supply roll into the Media Compartment of

printer.

Media Shield

Media Hanger

Media Compartment



17


6. Press the lock of Media Guide at the right to adjust media guides‟

positions. Make sure media stays under the Media Shaft and

centrally under both of the Media Guides.

7. Close the printer module and then press firmly at the both sides to

properly latch until you hear a click.

Media

Guides

Media Shaft



18


8. Press the FEED button to feed labels out of the printer.

9. To tear media, pull the media edge against the Tear Bar as in the

direction below:

Tear Bar

Tear Direction



19


Setting Media Type

To index labels with multiple columns, please select media types to

Multi-Column Labels in the label editing software Bartender UL.

Software setting steps:

Argox Bartender UL / Seagull Driver – Media Types – Multi-Column

Labels

Sample of labels with multiple columns:



20


Loading Ribbon

The following steps only apply to thermal transfer printing mode only.

Direct thermal does not need ribbon to be installed.

Preparing Ribbon

Find the two Ribbon Core Adaptors in printer package and fix them

into new ribbon rolls from the left to the right.

Note:

- Media and ribbon types should be matched to provide with

optimal print results.

- Always use ribbon that is wider than the media to protect the print

head from wear.

- For direct thermal printing, do not load ribbon in the printer.

Ribbon Core Adaptor



21


Placing Ribbon Rolls

1. Open Top Cover of the printer.

2. Push the Release Latch to open the printer module.

Top Cover

PUSH

Module

Release Latch



22


3. Lift up the printer module to check the Ribbon Supply Holder.

Ribbon Supply Holder



23


4. Install one ribbon roll and rotate it until the notches align and lock

into the left side of Ribbon Supply hub, and then into the right.

Ribbon Supply Holder

Note:

The Ribbon Supply Holder accepts the coated side of ribbon to

be wound ink-side IN or wound ink-side OUT.



24


5. Install the other ribbon roll and rotate it until the notches align and

lock into the left side of Ribbon Pick-up hub, and then the right.

Ribbon

Pick-up

Holder

Note:

The Ribbon Pick-up Holder accepts the coated side of ribbon to

be wound ink-side OUT only.



25


6. Close the printer module and then press firmly at the both sides to

properly latch it until you hear a click.

7. Rotate Thumb Wheel of Ribbon Pick-up Holder to remove slack

and ribbon wrinkle, and to align the ribbon on the spindles.

Thumb Wheel



26


Cutter Option

CP Series printers support cutter option for various media types,

including label liner, tag and receipt media, etc. The following steps

describe how to install the cutter module onto printers.

Note:

- Maximum of. media thickness for this cutter option: 0.2mm.

- Minimum media length (distance between cuts):

0.59 inches (15mm)Cutting shorter media length may cause the cutter to jam.

Warning : Never attempt to insert fingers or objects in to the cutter.



27


Installing Cutter

1. Power off the printer.

2. Open Top Cover. Remove Front Cover.

Middle Cover

Front Cover

Top Cover



28


3. Loose the two screws (item J) under Bottom.

Pull out to unlatch the front side of Middle Cover and then remove it

from Bottom.

4. Loose the screws (item D) at both sides of Printer Module to take

Printer Module off from Bottom. Find Cutter Baby Board in cutter

package, and then install onto JP16 socket on printer main board.



29


Cutter Baby Board

Printer Module

Middle Cover

Bottom



30


5. Remove Mylar Film from Printer Chassis. Thread Cutter

cable through the hole where Mylar Film locates, and then plug onto

JP9 connector (CUTTER) on printer main board. Cutter Cable should

go though the hooks under Printer Chassis to manage cables better.6. Make sure Cutter Cable go upon the font side of Middle Cover.

Assemble back Printer Chassis and Middle Cover with screws.

7. Install Cutter Module by fixing Cutter Bracket (item L) on Printer

Chassis with screws.

Now cutter installation has been completed through the steps above.

To load media, please refer to the section – Loading Media.



31


Mylar film

Middle Cover

Printer

Chassis

Cutter Module

Cutter Cable



32


Printer Operations

Printing Media Calibration & Configuration

Before connecting the printer to your computer, to make sure that

the printer works properly, conduct media calibration and print a

self-test/ configuration label.

Steps to Start Media Calibration & Configuration1. Make sure the media is properly loaded and the top cover of

the printer is closed.

2. Turn off the printer power.

3. Press and hold the FEED button while turning on the power,

until printer motor is activated.

4. Media Calibration will be performed while the printer

automatically feeds the label stock for a certain length; thenthe printer motor suspends for one second and then prints out

a configuration profile. Release the FEED button as soon as

printer starts to print.

Note:

If printer is with Argox PPLB printer language, printer will enter

Dump mode after printing configuration. In Dump mode, allcharacters will be printed in 2 columns: the right shows characters

received from your system, and the left are the corresponding

hexadecimal values of the characters. It allows users or engineers

to verify and debug the program.

To return to normal operation mode from Dump mode, press the

FEED button again. Another way is to turn off printer power, and

then restart printer.



33


Sample of Printer Configuration Label

Memory capacity

Print speed and darkness

Firmware version & date code

Print methodMedia sensor type

Real Time Clock (RTC) setup(available only with RTC Card)

Internal fonts

Printed label length

Serial port settings

Media type settingPrint width setting

Label length setting

Codepage

Backfeed setting

Calibration mode type

Cutter setting



34


Ethernet information -for CP-2140E only

Print head test pattern

Main board DIP switch settings



35


Resetting Printer to Factory Defaults

Follow the steps below to reset printer to default settings:1. Turn on the printer and wait for 5 or more seconds.

2. Press the "FEED" button for 10 seconds, and the "Ready"

indicator and "Power" indicator will go off in order.

3. Once "Power" indicator becomes lit again, release the FEED

button.

4. "Ready" indicator will then become lit, too. At this moment,

the printer has resumed its factory default settings.

Note:

The printer factory default settings are stored in printer ‟s flash;

these settings remain stored, without being erased even the printer

power is disconnected.



37


Control /

Indicator Function

Power

Switch

On: turns on normal operation (at “I” position)

Off: turns off power ( at “O” position)

Note: Turn power off before connecting or

disconnecting cables

Power LED

It will start blinking while “Media Out”, “MediaGap Not Found” or “Ribbon Out” has beendetected.

Once printer cutter mode has been enabled,when Cutter is jammed with paper or Cutter isnot installed, POWER indicator will blink.

When RS-232 communication error isdetected, POWER indicator will blink.

Ready LED

When printer is started, the READY indicatorwill blink. In Ethernet model, the READYindicator will blink for several seconds to waittill Ethernet Card is ready.

When printer receives data from host PC,READY indicator will start blinking.

READY indicator will blink when printing ispaused.

It will start blinking while “Media Out”, “MediaGap Not Found” or “Ribbon Out” has beendetected.

It will blink as soon as the printer module isopened.



38


Note:

When the print head is over-heated, printer ‟sthermal protection function will be activated and

make READY LED blink to indicate printer is in

PAUSE status to wait till print head has been

cooled down. The printing tasks sent previously

will be resumed automatically later.

Feed Button

Press to advance the label media to the firstprinting position.

Press during printing to make printer "pause".

Press and hold while switching on the power toconduct media calibration and print out aconfiguration profile.

To resume printing after “Media Out “or“Ribbon Out “ errors have been resolved.



39


Troubleshooting by LED Indicators Diagnosis

Normally, when the printer is in not working properly, the "Power"

LED blinks continuously, and printing and communication

between the host and printer stops. Refer to LED indications

listed below to understand possible solutions to resolve the

problems printer run into.

LED Indicators: Power and Ready LEDs blink at the same tempo

Power LED Ready LED

ON ON

OFF OFF

Possible Problems Solutions Remarks

Media sensor cannot

index label gaps

Check the label path

Check the label sensor

If a continuous label roll

is in use, set

“continuous media”

printing in driver

settings or commands.

Media out Install a new label roll

Paper jam Recover the jam



40


LED Indicators: Power and Ready LEDs blink alternately

Power LED Ready LEDON OFF

OFF ON


Ribbon out Install a new

ribbon roll

Set “Direct Thermal”

printing by driver or

commands if no ribbon is

required.

LED Indicators: Only the Power LED blinks

Power LED Ready LED

ON ON

OFF ON


Serial IO error Check serial baud rate at

both of your system and

the printer.

For serial

interface only

Cutter has failed, orthere is paper jam

inside the cutter.

Check the cutter orrecover paper jam.

Only applicablewhen cutter

mode to cutter

mode.

Other possible

hardware errors.

Contact the reseller for

further service.



43


Poor printout quality:

The ribbon may not be qualified. The media may not be qualified.

Adjust the Darkness (heat temperature).

Slow down the print speed.

Refer to the next chapter and clean the related spare parts.

Recovery

After correcting problems, simply press the panel button or restart

the printer to continue your print jobs. Make sure the LEDs are not

blinking and remember to resend your files.



44


Communications

Interfaces and Requirements

Argox CP printer series come with a nine-pin Electronics

Industries Association (EIA) RS-232 serial data interface, a USB

interface, Parallel, and Ethernet. A variety of interface options are

suitable for versatile applications:

CP-2140,CP-2140Z,CP-3140: Parallel, USB, and Serial

interfaces

CP-2140E: Ethernet, USB, and Serial interfaces

USB Interface Requirements

The Universal Serial Bus (USB) interface is version 2.0 and 1.1compliant and provides a full-speed (12Mb/s) interface that iscompatible with your existing PC hardware. The USB‟s “plug andplay” design makes installation easy. Multiple printers can share asingle USB port/hub.

Note: 1. You must insert the power supply‟s barrel connector into the

power jack on the back of the printer before connectingcommunication cables.

2. This printer complies with FCC Rules and Regulations, Part 15,for Class A Equipment, for use with fully shielded six-foot datacables. Use of longer cables or unshielded cables may increaseradiated emissions above Class A limits.



45


Serial (RS-232) Interface Requirements

The required cable must have a nine-pin "D" type maleconnector on one end, which is plugged into the mating serialport located on the back of the printer. The other end of thesignal interface cable connects to a serial port on the hostcomputer.

Parallel Interface Requirements

The required cable (IEEE 1284-compliant is recommended)must have a standard 36-pin parallel connector on one end,which is plugged into the parallel port located on the back of theprinter. The other end of the parallel interface cable connects tothe printer connector at the host computer. For pin-outinformation, refer to the Reference Technical Information,Interface Specification.

Serial and Parallel Cabling Requirements

Data cables must be of fully shielded construction and fitted with

metal or metalized connector shells. Shielded cables and

connectors are required to prevent radiation and reception of

electrical noise.

To minimize electrical noise pickup in the cable:

1. Keep data cables as short as possible.

(6 ft or 1.83m recommended)

2. Do not tightly bundle the data cables with power cords.

Note:

For technical and pin-out information, please refer to the Technical

Reference, Interface Specifications in this manual.



47


Communicating with the Printer

The bundled printer driver can be applied to all applications under

Windows XP/ Vista/ Windows 7, supporting 32-bit/ 64-bit

operation systems. With this driver you can operate any popular

Windows software applications including Argox Bartender UL

label editing software or MS Word, etc., to print to this printer.

The following installation steps are based on CP-2140 as anexample. The screens included for these steps are taken fromWindows XP; steps in other versions of operation systems aresimilar. Drivers can be installed via the CD-Rom included inprinter package; or it can be downloaded from Argox website >>Technical Support >> Download Center >> select product modelto access: http://www.argox.com/content.php?sno=0000033

Installing a Plug and Play printer driver (for USB only)

Note:

We strongly recommend that you use the Seagull Driver Wizard

instead of the Microsoft Windows Add Printer Wizard when

installing and updating your Drivers by Seagull.

(Even though the "Add Printer Wizard" is from Microsoft, it tooeasily performs a number of tasks incorrectly when updating

existing drivers. It also badly handles the situation where a printer

driver is already in use by a Windows application.)

http://www.argox.com/content.php?sno=0000033

http://www.argox.com/content.php?sno=0000033



49


4. Under CP-2140/ CP-2140Z/ CP-2140E/ CP-3140 product

selection prompt, choose Seagull Driver version and then start

installation:

Instead of the flash prompt above, another way to install

Seagull driver is to run the DriverWizard utility from the

Installation Directory where the Seagull driver files are located.



50


5. On the Seagull Driver Wizard prompt, select the first radio

button to “Install a driver for a Plug and Play printer ”:

Then click “Next.”



51


6. Enter Printer name (i.e. Argox CP-2140 PPLB) and select "do

not share this printer”, and click "Next"

7. Check all the data on the showing screen, if it is correct, click

"Finish".

Argox CP-2140 PPLB

Argox CP-2140 PPLB

Argox CP-2140 PPLB

USB002



53


Installing a Printer Driver (for other interfaces except USB)

1. Turn off the printer. Plug the power cable into the power

socket on the wall, and then connect the other end of the

cable to printer's power socket. Connect the Parallel cable,

Serial cable, or Ethernet cable to the proper port on the printer

and on your computer.

2. Prepare the documentation and software CD-Rom fromprinter package and then install to CD-Rom drive of your

computer. The CD-Rom will bring out the following prompt.

Click “Go”:



54


3. Under CP-2140/ CP-2140Z/ CP-2140E/ CP-3140 product

selection prompt, choose Seagull Driver version and then start

installation:

Instead of the flash prompt above, another way to installSeagull driver is to run the DriverWizard utility from theInstallation Directory where the Seagull driver files are located.



55


4. On the prompt, Windows Printer Driver, select “I accept…” and click "Next".

5. Assign the directory to keep Seagull driver, (for example:

C:\Seagull) and click "Next".



56


6. Click "Finish".

7. Select Install printer drivers and Click "Next"



57


8. Select model & emulation - the following examples are based

on model CP-2140 PPLB:

9. Select the port of the printer and click "Next".

Argox CP-2140 PPLB

LPT1 Parallel Port40 PPLB



58


10. Enter Printer name (i.e. Argox CP-2140 PPLB) and select

"do not share this printer”, and click "Next".

11. Check all the data on the showing screen, if it is correct, click

"Finish".

Argox CP-2140 PPLB

Argox CP-2140 PPLB

Argox CP-2140 PPLB

Argox CP-2140 PPLB

LPT1



59


12. After the related files have been copied to your system, click

"Finish".

13. After driver installation is complete, click "Close".

The driver should now be installed.

Installing printer „Argox CP-2140 PPLB‟…

Installed printer Argox CP-2140



60


Caring for Your Printer

Print Head Maintenance GuideTo keep the Print Head remain in the best conditions and

efficiency and to extend duration for use, regular cleaning action

is needed:

Cleaning Interval

It‟s strongly recommended to regularly clean print heads at leastwhen changing every one label roll (in direct thermal printingmode) or every one ribbon roll (in thermal transfer printing mode).In addition, if printers are operated under critical applications and

environments, or if it‟s f ound that print quality is degraded, pleaseclean print heads more frequently.

Cleaning Material

Surface of print head‟s heating element is very fragile. To preventfrom any possible damage, please use soft cloth/ cotton buds with“Ethanol” or “IPA” to clean print head surface.It‟s strongly recommended to wear hand gloves during cleaning

progress.Do not touch print head surface by bare hands or with any hardequipment.Water or spit should be kept away in case of corrosion on heatingelements.

Note: Always switch off printer power before cleaning.



61


Cleaning Direction

When cleaning the print head, always wipe in One-Way Direction- from Left to Right only, or, from Right to Left only, to clean“Heating Line” of print head gently without excessive stress.Do not wipe back and forth, to avoid dust or dirt on cleaning cottonwould be attached onto print head again.

Special Caution:

Warranty of print heads will be void if print head serial number is

removed, altered, defected, or made illegible, under every

circumstance.



62


Product Specification

General Specification

SpecificationsCP-2140

CP-2140ZCP-2140E CP-3140

Printing Method Direct Thermal / Thermal Transfer

PrintingResolution

203 dpi(8 dots/mm)300 dpi

(12 dots/mm)

Printing Speed 2~4ips (50.8~101.6mm/s)1~up to 4ips(25.4~101.6

mm/s)

Printing LengthMax 100”(2540mm)

Min 0.2”(5mm) Max 50”(1270mm)

Min 0.2”(5mm)

Printing Width Max 4.1”(104mm)

Memory8MB DRAM (5MB user available)

4MB Flash ROM (2MB user available)

8MB DRAM(5MB useravailable)

8MB Flash ROM(6MB user

available)CPU Type 32 bit RISC microprocessor

Sensors

Media Reflective sensor x 1 (movable) &Media Transmissive sensor x 1 (Center fixed) /

Head open switch /Ribbon end sensor

OperationInterface

LED indicator (Power/Ready)x 2, Button(Feed) x 1

CommunicationInterface

Parallel,RS-232(Baud rate:2400~115200 bps),

USB(2.0)

Ethernet

RS-232(Baudrate:

2400~115200bps), USB(2.0),

Parallel,

RS-232(Baudrate:

2400~115200bps), USB(2.0)

Fonts

Internal character sets standard5 alpha-numeric fonts from 0.049”H ~ 0.23” H(1.25mm ~ 6.0mm)Internal fonts are expandable up to 24x244 direction 0 ~ 270 rotation



63


Soft fonts are downloadable

1D Barcodes

PPLA: Code 39 (standard/with checksum digit), Code 93

Interleaved 2of 5 (standard/with checksum digit/with humanreadable check digit), EAN-8, EAN-13,UPC-A, UPC-E,Postnet, Codabar, Code 128 subset A/B/C, UCC/EAN-128,UCC/EAN-128 K-MART, UCC/EAN-128 , Random Weight,Plessey, HBIC, Telepen, FIM, UPC2, UPC5, GS1 Data Bar

PPLB: Code 39 (standard/with checksum digit),Code 93Interleaved 2 of 5 (standard/with checksum digit/with humanreadable check digit), EAN-8 (standard/2 digit add-on/5 digitadd-on), EAN-13 (standard/2 digit add-on/5 digit add-on),UPC-A (standard/2 digit add-on/5digit add-on), UPC-E(standard/2 digit add-on/5 digit add-on), Postnet, Codabar,Code 128 subset A/B/C, Code 128 UCC (Shipping ContainerCode), Code 128 Auto, German, Postcode, Matrix 2 of 5,UCC/EAN 128, UPC Interleaved 2 of 5, GS1 Data Bar

PPLZ: Code39、UPC-A、UPC-E、Postnet、Code128 subset A/B/C、Interleave 2 of 5、Interleaved 2 of 5 with checksun、Interleaved 2 of 5 with human readable check digit、

Code 93、

Code 39 with check sun digit、

EAN-8、

Codabar 、

EAN-13、Plessey、GS1 Data bar

2D BarcodesPPLA/PPLB/PPLZ:MaxiCode, PDF417, Data Matrix (ECC 200 only), QR code,Composite codes

Graphics

PPLA: PCX, BMP, IMG, GDI, HEX format filesPPLB: PCX, binary raster, BMP, GDI

PPLZ: GRF, Hex, GDI

Emulation

CP-2140, CP-2140E, CP-3140: PPLA, PPLB

CP-2140Z: PPLZSoftware -Label editing

Seagull Driver, BarTender

Software - Utility Printer Utility, Font Utility

Media TypeRoll-feed, die-cut, continuous, fan-fold, tags, ticket in

thermal paper or plain paper and fabric label

MediaMax Width:4.33”(110mm) Min Width:1”(25.4mm)Thickness:0.0025”~0.01”(0.0635~0.254mm)Max roll capacity(OD):5”(127mm) Core size:1”(25.4mm) /



64


Max roll capacity(OD):4.5”(114.3mm) Coresize:0.5”(12.7mm) (optional)

Min Length: 0.59“(15mm) for cutter option

Ribbon

Ribbon roll – max OD: 2.6”(67mm)Ribbon Length: max 300mCore size – ID: 1”(25.4mm)Ribbon Width: 1”~4” Wax, Wax/Resin, Resin(Ribbon wound ink-side out or ink-side in)

Dimensions L 273mm x W 225mm x H 186mm

Weight 2.1kg

Power SourceUniversal Switching Power Supply ACInput: 100~240V,1.8A, 50-60Hz, DCOutput: 60W Max.24V 2.4A

Universal

Switching PowerSupply AC Input:100~240V,1.5A,50-60Hz,DC Output: 24V,2.91A Typical,70W Max.

OperationEnvironment

Operation Temperature: 40F~100F (4C~38C), 10% ~90% non-condensing,

Storage Temperature: -4F~122

F (-20

C~50

C)Optional Items Cutter, Stacker, RTC Card, ArgoKee

Agency Listing CE, FCC, cTUVus, CCC, RoHS

Fonts, Barcodes, and Graphics Specification

The specifications of fonts, bar codes and graphics depends on

the printer emulation. The emulations PPLA, PPLB, and PPLZ are

printer programming languages, through which the host can

communicate with your printer.



65


Printer Programming Language PPLA

ProgrammingLanguage

PPLA

Internal fonts 9 fonts with different point size6 fonts with ASD smooth font.Courier font with different symbol sets.

Symbol sets(Code pages)

Courier font symbol set: Roman-8, ECMA-94, PC,PC-A, PC-B, Legal, andPC437 (Greek), Russian.

Soft fonts Downloadable soft fonts

Font size1x1 to 24x24 times

Characterrotation

0, 90, 180, 270 degree, 4 direction rotation

GraphicsPCX, BMP, IMG, GDI and HEX format files

1D Barcodes Code 39、

UPC-A、

UPC-E、

Code 128 subset A/B/C、

EAN-13、EAN-8、HIBC、Codabar 、Plessey、UPC2、

UPC5、Code 93、Postnet 、CC/EAN Code 128 、

K-MARK、UCC/EAN Code 128 Random、Telepen、

FIM、UCC/EAN code 128、Interleave 2 of 5 、

Standard/with checksum/with human readable 、

heck digit) 、GS1 Data bar (RSS)

2D Barcodes MaxiCode、

PDF417、

Data Matrix (ECC 200only) 、QR code、Composite Codes



66


Printer Programming Language PPLB

ProgrammingLanguage

PPLB

Internal fonts 5 fonts with different point size


8 bits code page : 437, 850, 852, 860, 863, 865,857, 861, 862, 855, 866,737,851,869, 1252, 1250, 1251,

1253, 1254, 12557 bits code page: USA, BRITISH, GERMAN,FRENCH, DANISH, ITALIAN,SPANISH, SWEDISH andSWISS.

(300dpi printer models support Code page 437,850, 852, 860, 863, 865 only)

Soft fonts Downloadable soft fonts

Font size1x1 to 24x24 times

Characterrotation


GraphicsPCX , Binary Raster, BMP and GDI

1D Barcodes Code 39、UPC-A、UPC-E、German Postnet、Matrx

2 of 5、UPC-Interleaved 2 of 5、

Code 39 with check sum digit 、Code 93、EAN-13、

EAN-8 (Standard, 2 /5digit add-on) 、Codabar 、

Postnet、Code128 subset A/B/C、

Code 128 UCC shipping container code) 、

Code 128 auto、UCC/EAN code 128 (GS1-128) 、

Interleave 2 of 5、Interleaved 2 of 5 with check

sum、

Interleaved 2 of 5 with human readable check digit

German Postcode、Matrix 2 of 5、UPC Interleaved



67


2 of 5、EAN-13 2/5 digit add-on、UPCA2/5 digit

add-on、

UPCE 2/5 digit add-on、GS1 Data bar (RSS)2D Barcodes MaxiCode、PDF417、Data Matrix (ECC 200

only) 、QR code、Composite Codes

Printer Programming Language PPLZ

Programming

Language

PPLZ

Internal fonts 8 (A~H) fonts with different point size.8 AGFA fonts: 7 (P~V) fonts with fixed differentpoint size (not scalable). 1 (0) font with scalingpoint size.


USA1, USA2, UK, HOLLAND,DENMARK/NORWAY,

SWEDEN/FINLAND, GERMAN, FRANCE1,FRANCE2, ITALY,

SPAIN, MISC, JAPAN, IBM850.

Font size 1x1 to 24x24

Characterrotation


Soft fonts True Type fonts can be downloaded by FontUtility

(Two-byte Asian fonts also can be downloaded to

X-3200Z / X-2300ZE / X-3200ZE)1D Barcodes Code39

UPC-AUPC-EPostnetCode128 subset A/B/CInterleave 2 of 5Interleaved 2 of 5 with check sunInterleaved 2 of 5 with human readable check



68


digitCode 93

Code 39 with check sun digitEAN-8CodabarEAN-13PlesseyGS1 Data bar (RSS)

2D Barcodes MaxiCodePDF417Data Matrix (ECC 200 only)

QR codeComposite Codes

Graphics GRF, Hex and GDI



69


Interface Specification

This section presents the interface specifications of IO ports forthe printer. These include pin assignments, protocols and detailed

information about how to properly interface your printer with your

host or terminal.

USB Interface Complies with USB 2.0 Full Speed.

Connector Terminal Pin Assignment

Pin Signal Description

1 VBUS 5V

2 D - Differential data signaling pair -

3 D + Differential data signaling pair +

4 GND Ground

12

3 4

12

3 4

USB series “B” Receptacle Interface



70


Serial Interface

The RS232 connector on the printer side is a female, DB-9.

Pin Signal Description

1 No function Shorted to Pin - 6

2Received Data,RxD

Input. Serial “Received Data”

3 Transmitted Data,TxD

Output. Serial “TransmittedData”.

4 No function No connection

5 GND Signal Ground

6 No function Shorted to Pin - 1

7Request to Send,RTS

Output. Used as the controlsignal for “H/W Flow Control “

8 Clear to Send, CTS

Input. Used as the control

signal for “H/W Flow Control”

9 +5VOutput. Pin 9 is reserved forKDU (keyboard device unit)

Note :

Pin 9 are reserved fo r KDU (keyboard device unit), therefore

do not conn ect these pins i f you are using a general hos t l ike

a PC.



71


Parallel (Centronics) Interface

The parallel port is a standard 36-pin Centronics, which complieswith IEEE 1284 standard (compatibility mode). Pin assignments

are as follows:

Pin Direction Definition Pin Direction Definition

1 In n/STROBE 16 - Ground

2~9 In Data 1~8 17 - Ground

10 Out nACK 18 - NC

11 Out BUSY 19~30 - Ground

12 Out PE 31 In NC

13 Out 5V 32 Out nFAULT

14 In NC 33~35 - NC

15 - NC. 36 In NC

Auto Polling

Both the serial port and parallel port of this printer can be

activated at the same time, i.e the printer can simultaneously

communicate with two PCs via different ports. However as no port

contention is made for this printer, if both PCs transmit data at the

same time the data may become damaged in the receiving buffer.

Ethernet Interface



72


The following port complies with Ethernet communication.

Pin Signal

1 Transmit+

2 Transmit-

3 Receive+

4 Reserved

5 Reserved

6 Receive-

7 Reserved

8 Reserved

1 2 3 4 5 6 7



73


Connection with Host

Host 25S Printer 9P Host 9S Printer

9P(PC or compatible) (PC or compatible)

DTR 20 …… 1 DSR DTR 4 …… 1 DSR

DSR 6 …… 6 DTR DSR 6 …… 6 DTR

TX 2 …… 2 RX TX 3 …… 2 RX

RX 3 …… 3 TX RX 2 …… 3 TXCTS 5 …… 7 RTS CTS 8 …… 7 RTS

RTS 4 …… 8 CTR RTS 7 …… 8 CTS

GND 7 …… 5 GND GND 5 …… 5 GND

Alternatively you can just connect the 3 wires in the following

way.

Host 25S Printer 9P Host 9S Printer

9P

(PC or compatible) (PC or compatible)

TX 2 …… 2 RX TX 3 …… 2 RX

RX 3 …… 3 TX RX 2 …… 3 TX

GND 7 …… 5 GND GND 5 …… 5 GND

pin 4 pin 4

pin 5 pin 6

pin 6 pin 7

pin 20 pin 8



The simplest way to connect to other hosts (not PC compatible)

or terminals is:

Printer Terminal/Hos

t

Pin 2- RxData ……… TxData

Pin 3- TxData ……… RxData

Pin 5- Ground ……… Ground

In general, as long as the data quantity is not too large and you

use Xon/Xoff as flow control, it will be problem free.

Baud rate: 2400, 4800, 9600(default), 19200, 38400, 57600,

115200 bauds.(programmable by command)

Data format: always 8 data bits, 1 start bit and 1 stop bit.

Parity: always non parity

Handshaking: XON/XOFF as well as CTS/RTS (hardware flow

control).

argox manual

Documents