aquator manual training

7/27/2019 Aquator Manual Training

http://slidepdf.com/reader/full/aquator-manual-training 1/13

of 13

Infravera Sdn. Bhd.(920487-X) No 6-3, JalanPuteri 2/4, Bandar PuteriPuchong, 47100 Puchong, Selangor.Website : www.infravera.com

Tel: 03-8063 5733 Fax: 03-8051 4637 Email: [email protected] (Sales) [email protected] (Tech. Support)

AQUATOR VERSION 2

MODELING AT CAD

ITEM STEP

1. Clean The Drawing

a.

Faster analysis in the

software

b.

Prevent bad/error

entities

c.

More accurate result

d.

Smoother modeling

experience

i.

Ensure the drawing does not contain 3D element /entities.

ii.

To ensure higher quality of clean drawing, copy necessary layers and

paste to a new drawing.

2. Scale

a.

To prevent error or

entities

i.

The best scale to import to the Aquator is 1:1.

3. Add New Layers

a.

CSSS-USERWATER

i.

Select LAYERS icon

ii.

Select NEW icon to add new layers.

iii.

Type for new layer (make sure in capital letter and spell with right )

and change any colour user want;

a.

CSSS-USERWATER

Select NEW layer icon

Insert both layer names



of 13



ITEM STEP

4. Draw water

reticulation lines.

a.

Need to use single line

to draw.

b.

Make sure stop at

intersection.

a) CSSS-USERWATER

i.

Make sure change the current layer to CSSS-USERWATER

ii.

Select single line and start to draw the water reticulation line.

iii.

Make sure draw the single line and stop at every intersection.

iv.

Node will be created based the mouse click.

5. Save project

a.

Project need to be

close before import the

drawing into the

INFRAVERA software

i.

Select FILE.

ii.

Select SAVE AS to save the project.

iii.

Save the project

iv.

Close/Exit the project before import into the software

SELECT FILE

SELECT SAVE AS

WATEREC LINE



of 13



SOFTWARE

1. IMPORT DRAWING

STEP

1.

Select the CAD IMPORT button.

2.

Located the CAD drawing.

3.

Drawing Scale will pop up after select the CAD drawing.4.

Select ACCEPT for drawing scale.

5.

Water Supply Guideline will pop up, select the design guide based the project.

6.

For example, select SYABAS.

7.

The layout CAD will appear.

SELECT CAD IMPORT

SELECT ACCEPT

i. SELECT SYABAS

ii. SELECT OK



of 13



2. WATER TAB

STEP

1. Select WATER tab to start design water reticulation

2. To show the water reticulation line only, press space bar at keyboard

SELECT WATER TAB



of 13



3. ADD TAPPING POINT & PRESSURE HEAD

STEP

1. Select first node as tapping point. In yellow colour, the node is selected.

2. Go to properties tab , at left hand side software.

3. At properties tab, Input term, change tapping point to TRUE.

4. Indicate the value for tapping pressure head by insert the number.

4. WATER DEMAND (Q)

i)

Have two method’s to key in;

a.

By Table

b.

By Properties

STEP

a.

By table

1.

Select last nodes, for example, node number 5.

2.

By right click mouse at nodes, the mouse properties will pop up.

3.

Select for table.

CHANGE TO TRUE

KEY IN THE PRESSURE

HEAD VALUE



of 13



4.

Table for water demand will pop up.

5.

Select ADD button to add the table.

6.

Select CALC button to calculate the sub total Q.7.

Item for type of house, unit of house and water demand unit can be choosing based user.

8.

Select OK if satisfied with the data.

9.

Done water demand for that node.

b.

By Properties1.

Select the nodes, and go to properties.

2.

Indicate the level for that water demand manually.

3.

For example, 0.52.

i. SELECT THE NODES

ii. SELECT TABLE

ii.

SELECT CALC

BUTTON

iii. SELECT OK BUTTON

i. SELECT ADD

BUTTON



of 13



4.

Press ENTER button at keyboard.

5. HYDRANT

STEP

1.

Select the nodes.

2.

Go to properties, select for Hydrant.

3.

Change the hydrant to TRUE.

4.

Hydrant will pop up at layout.

SELECT THE NODES

KEY IN THE WATER

DEMAND

SELECT THE NODES

CHANGE HYDRANT

TO TRUE



of 13



6. FITTING/PUMP

STEP

1.

By select the pipe, right click mouse at that pipe.

2.

Select for fitting or pump. If select for fitting, choose the types of fitting to add on.

3.

For example, select for air valve fitting.

4.

Air valve fitting icon will appear at layout.

5. Key in the head loss for air valve, by select component at properties.

i. SELECT FITTING

ii. SELECT AIR VALVE

i. SELECT THE

COMPONENT

ii. KEY IN THE HEAD

LOSS



of 13



7. RUN RESULT

STEP

1.

Select INTEGRITY icon before run.

2.

INTEGRITY PASS information will pop up.3.

Select OK button

4. The output data can be check at information tab (below tab)

8. SECTIONS

STEP

1.

Select SECTIONS icon.

2.

Section Data will be appearing at left side. Tick all the section.

3.

Select BUILD button to generate section.

SELECT OK

SELECT SECTIONS



of 13



STEP

4.

Section will appear at section layout.

5.

To change the datum of slope, select SETUP button.

6.

Setup for CAD section will pop up, search for DATUM, and change the value. For example 80.

7.

Done change the datum value, select OK button.

8.

The data need to be change by re-select BUILD button.

9.

The section with new datum will be pop up again at layout section too.

TICK ALL THE SECTION

SELECT BUILD

CHANGE THE

DATUM VALUE

SELECT OK

BUTTON



of 13



10. 3D VIEW

i) To view data input in 3D environment.

STEP

1.

Select 3D View icon.

2.

3D image will appear.

11. CALCULATION

i) Break down water reticulation calculation.

STEP

. Select Calculation icon.

2. The data calculation table will be pop up.

3. Click Select All button, and then Select show button.

4. The calculation will be appear.



of 13



STEP

12. SAVE PROJECT

STEP

1.

Select file icon.

2.

Select save as to save the project.

3. Make sure save the project in one’s folder.

SELECT ALL

BUTTON

SELECT SHOW

SELECT SAVE AS



of 13



13. GENERATE REPORT

STEP

1.

Select REPORT tab.

2. Select WATER iconto generate the report.

3. The report will be pop up.

4. To change the format of report,select file and select EXPORT DOCUMENT and choose the format.

5. Or user also can select Export Document icon to change the format.

SELECT REPORTS

TAB

aquator manual training

Documents