appendix iv tariff codes - mytradelink...page 6 of 16 19 - other 7208 54 990 7208.54.00 99 plates,...

APPENDIX IV Tariff Codes

NO PRODUCT TARIFF CODE

TARIFF CODE (ASEAN)

MALAYSIAN STANDARDS / ISO/ FNS

Unglazed /Glazed Ceramic Tiles 6907 / 6908

1 Unglazed Ceramic Tiles (<7cm) 690710100 6907100010 MS ISO 13006:2003

2 Unglazed Ceramic Tiles (>7cm) 690790100 6907900010 MS ISO 13006:2003

3 Glazed Ceramic Tiles (<7cm) 690810100 6908100010 MS ISO 13006:2003

4 Glazed Ceramic Tiles (>7cm) 690890100 6908901010 MS ISO 13006:2003

Ceramic Pipes and Pipe Fittings 6906

1 Ceramic pipes, conduits, guttering and pipe fittings

6906 00 000 6906000000 MS 1061:Part 2:2008

Sanitaryware 6910 / 3922

1 Ceramic Flushing Cisterns Not Equipped With Mechanism

6910 10 900 6910100090 MS 147:2001

2 Ceramic Wash Basin (Pedestal) 6910 10 200 6910100020 MS 147:2001

3 Ceramic Flushing Cisterns Equipped With Mechanism

6910 10 900 6910100090 MS 795:2002, MS 147:2001

4 Ceramic Wash Basin 6910 10 200 6910100020 MS 147:2001

5 Ceramic Water Closet Pans Without Flushing Cisterns

6910 10 900 6910100090 MS 147:2001, MS 1522:2007

6 Ceramic Bidets 6910 10 900 6910100090 MS 147:2001

7 Ceramic Urinals 6910 10 900 6910100090 MS 147:2001

8 Ceramic Water Closet Pans With Flushing Cisterns (One Piece)

6910 90 900 6910900090 MS 147:2001, MS 1522:2007, MS 795:2002

9 Plastic Flushing Cisterns Equipped With Mechanism

3922 90 110 3922901911 MS 795:2002

Portland Cement 2523

1 White Portland Cement 2523 21 000 2523101000 MS 888:1991

2 Portland Cement (Ordinary and Rapid Hardening)

2523 29 900 2523299000 MS 522 Part 1 :2007

3 Sulfate-resisting Portland Cement 2523 29 900 2523299000 MS 1037:1986

4 Pulverised Fuel Ash Portland Cement 2523 29 900 2523299000 MS 1227:2003

5 Blast Furnace Portland Cement 2523 29 900 2523299000 MS 1389:1995

Hydraulic Cement 2523

1 Pozzolonic Pulverised Fuel Ash Cement 2523 90 000 2523900000 MS 1520 :2001

2 High Slag Blast Furnace Cement 2523 90 000 2523900000 MS 1388:1995

3 Masonry Cement 2523 90 000 2523900000 MS 794:2010

of 16

LIST OF ADDITIONAL CONSTRUCTION PRODUCT TO BE ENFORCED, EFFECTIVE DATE TO BE ADVISED

NO PRODUCT TARIFF CODE

TARIFF CODE (ASEAN)

MALAYSIAN STANDARDS

Insulation materials 6806 / 7019

1 Slag wool, rag wool and similar mineral wools, (including intermixtures thereof) in bulk, sheets or rolls

6806 10 000 6806 10 00 00

MS 1020 :2010

2 Thin sheets (voiles), webs, mats, mattresses, boards and similar non-woven products.

7019 19 900 7019.19.90 00

MS 1020 : 2010

3 Fibre (including wool) 7019 19 100 7019.19.10 00 MS 1020 : 2010

Clear Float Glass 7005

1 Other glass, non wired, non-coloured throughout the mass, in square or rectangular shape (including those with one or two or three or four corner cut).

7005 29 910 7005.29.90 10

MS 1138:Part 1-4:2007

2 Other float glass, non-wired, non-coloured throughout the mass other than square or rectangular shape (including those with one or two or three or four corner cut).

7005 29 900 7005.29.90 00

MS1135:2008

Tinted Float Glass 7005

1 Coloured throughout the mass (body tinted), opacified, flashed or merely surface ground: in square or rectangular shape (including those with one or two or three or four corner cut).

7005 21 910 7005.21.90 10

MS1135:2008

2 Other coloured throughout mass (body tinted), opacified, flashed or merely surface ground.

7005 21 990 7005.21.90 10

MS1135:2008

Reflective Glass 7005

1 non wired glass, having and absorbent, reflecting or non-reflecting layer: in square or rectangular shape(including those with one or two or three or four corner cut);

7005 10 910 7005.10.90 10

MS1135:2008

2 Other non wired glass, having and absorbent, reflecting or non- reflecting layer.

7005 10 910 7005.10.90 10

MS1135:2008

Wired Glass 7005

1 Wired glass in square or rectangular shape (including those with one or two or three or four corner cut).

7005 30 100 7005.30.00 10

MS1135:2008

2 Other wired glass.

7005 30 900 7005.30.00 90

MS1135:2008

Radiant Barrier 7607

1 Radiant Barrier 7607 2 90 10 MS 2095:2008

Fibre Cement Flat Sheet 6811

1 Roofing, facing and partition sheets.

6811 82 100 6811.82.00 10

MS 1296 : 1992

2 Floor and wall tiles containing plastics 6811 82 200 6811.82.00 20 MS 1296 : 1992

3 Others 6811 82 900 6811.82.00 90 MS 1296 : 1992

of 16

Aluminum plates, sheets and strip, of a Thickness exceeding 0.2 mm

7606

1 Of aluminum, not alloyed 7606 11 000 7606.11.00 00 MS 2040:2007

2 Of aluminum, alloys 7606 12 000 7606.12.10 00 MS 2040:2007

3 Of aluminum, not alloyed 7606 91 000 7606.91.20 00 MS 2040:2007

4 Of aluminum, alloys 7606 92 000 7606.92.30 00 MS 2040:2007

Aluminum Foil (whether or not printed or backed with paper, paperboard, plastics or similar backing materials of a thickness (excluding any backing) not exceeding 0.2 mm.

7607

1 Rolled but not further worked 7607 11 000 7607.11.00 00 MS 1848:2005

2 Other 7607 19 000 7607.19.10 00 MS 1848:2005

Steel Wire Products

1 Stranded wire, ropes, cables, plated, bands, strings and the like, or iron or steel, not electrically insulated-stranded wire, ropes and cables.

7312 10 000 MS1138:1989

2 Wire of iron or non-alloy-not plated or coated, whether or not polished

7217 10 000 MS 1137:1989

3 Other bars and rods of iron or non-alloy steel, not further worked than forged, hot-rolled, hot drawn or hot-extruded, but included those twisted after rolling, containing indentations, ribs, grooves, or other deformations produced during the rolling process or twisted after rolling.

7214 MS 146:2006

4 (of circular cross-section measuring less than 14 mm in diameter) Bars and rods, hot-rolled, in irregularly wound coils, of iron or non-alloy steel.

7213 91 000 MS 1092:1987 MS 1093:1987

of 16

NO PRODUCT TARIFF

CODE TARIFF CODE (ASEAN)

PRODUCT TYPE STANDARDS IDENTIFIED

Semi-finished products of iron or non-alloy steel

7207

- Containing by weight less than 0.25% of carbon:

1 Other 7207 11 900 7207.11.00 90 Billets, Blooms, Beam Blanks

MS 1494

2 Other 7207 19 900 7207.19.00 90 Blooms MS 1495

Containing by weight 0.25% or more of carbon:

3 containing by weight 0.6 % or more of carbon

7207 20 910 7207.20.91 00, 7207.20.99 90

Beam Blanks MS 1496

4 Other 7207 20 990 7207.20.11 00, 7207.20.19 90

Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, hot-rolled, not clad, plated or coated

7208

5 - In coils, not further worked than hot-rolled, with patterns in relief

7208 10 000 7208.10.00 00 Steel Strip and Sheet MS 1705:2003

6 - - Of a thickness of 4.75 mm or more

7208 25 000 7208.25.10 00, 7208.25.90 00

7 - - Of a thickness of 3 mm or more but less than 4.75 mm

7208 26 000 7208.26.00 00 Pipes and Tubes MS 1768:2004

8 - - Of a thickness of less than 3 mm

7208 27 000 7208.27.00 00

9 - - Of a thickness exceeding 10 mm

7208 36 000 7208.36.00 00

10 - - Of a thickness of 4.75 mm or more but not exceeding 10 mm

7208 37 000 7208.37.00 00

11 - - Of a thickness of 3mm or more but less than 4.75 mm

7208 38 000 7208.38.00 00

- - Of a thickness of less than 3 mm:

12 Containing by weight 0.6 % or more of carbon

7208 39 100 7208.39.00 10 Mild Steel Strip and Sheet

MS 1705:2003 JIS G3131

13 Other 7208 39 990 7208.39.00 99

14 - Not in coils, not further worked than hot-rolled, with patterns in relief

7208 40 000 7208.40.00 00 Pipes and Tubes MS 1768:2004 JIS G3132

15 - - Of a thickness exceeding 10 mm

7208 51 000 7208.51.00 00


7208 52 000 7208.52.00 00 Steel Strip and Sheet MS 1705:2003

of 16

17 - - Of a thickness of 3 mm or

more but less than 4.75 mm 7208 53 000 7208.53.00 00 Plates, Wide Flats and

Wide Strips MS 1721

Structural Steel MS EN 10025:2009

Structural Steel for Ships

ASTM A131 ASTM A283 ASTM A285

High-strength Low-Alloy Structural Steel

ASTM A242

Carbon Structural Steel Strip

ASTM A 36

Pressure Vessel Plate, Carbon Steel

ASTM A 515

Pressure Vessel Plate, Carbon Steel

ASTM A 516

Structural Steel ASTM A 572

Seamless Pipe API 5L

Rolled Steel for General Structure

JIS G 3101

Rolled Steel for Welded Structure

JIS G 3106

Steel Plates, Sheets and Strip

JIS G 3113

Steel Sheets, Plates and Strip for Gas Cylinders

JIS G 3116

Corrosion Resisting Rolled Steel

JIS G 3125

Hot Rolled High Strength Steel Sheets and Strip

JIS G 3134

18 - Containing by weight 0.6 % or more of carbon

7208 54 100 7208.54.00 10 Mild Steel Plates, Sheet and Strip

MS 1705:2003 JIS G 3131

of 16

19 - Other 7208 54 990 7208.54.00 99 Plates, Wide Flats and

Wide Strips MS 1721

Carbon Structural Steel

ASTM A36

Rolled Steel for General Structure

JIS G 3101 JIS G 3106

Pipes and Tubes MS 1768:2004 JIS G 3132



Steel Plates, Sheets and Strips

JIS G 3113

Steel Sheets, Plates JIS G 3116

Corrosion Resisting Rolled Steel

JIS G 3125

Hot-rolled High-strength Steel Sheets

JIS G 3134

Structural Steel for Ships

ASTM A131 ASTM A242 ASTM A283 ASTM A285

Carbon Structural Steel

ASTM A 36

Pressure Vessel Plate, Carbon Steel, Structural Steel

ASTM A515 ASTM A516


Flat-rolled products of iron or non-alloy steel, of a width of 600 mm or more, cold-rolled (cold-reduced), not clad, plated or coated

7209

- In coils, not further worked than cold-rolled (cold-reduced):

20 - - Of a thickness of 3 mm or more

7209 15 000 7209.15.00 00 Steel Sheet MS ISO 3574:2009 (P)

21 - - Of a thickness exceeding 1 mm but less than 3 mm

7209 16 000 7209.16.00 00 MS ISO 4997:2009 (P)


7209 17 000 7209.17.00 00 MS ISO 13887:2009 (P)

- - Of a thickness of less than 0.5 mm:

23 Other 7209 18 990 7209.18.10 99, 7209.18.90 90

Steel Sheet MS ISO 5001:2009 (P)

of 16

- Not in coils, not further worked than cold-rolled (cold-reduced):

24 - - Of a thickness of 3 mm or more

7209 25 000 7209.25.00 00 Steel Sheet MS ISO 5001:2009 (P)

25 - - Of a thickness exceeding 1mm but less than 3 mm

7209 26 000 7209.26.00 00


7209 27 000 7209.27.00 00

- Of a thickness of less than 0.5 mm:

27 Other 7209 28 990 7209.28.90 90 Steel Sheet MS ISO 5001:2009 (P)

Flat rolled products of iron or non-alloy steel, of a width of 600 mm or more, clad, plated or coated

7210

- Plated or coated with tin:

Electrolytically plated or coated with zinc:

28 1.5 mm or less in thickness 7210 30 910 7210.30.10 00 Steel Sheet MS ISO 5002:2009 29 more than 1.5 mm but less than

3 mm in thickness 7210 30 920 7210.30.90 91

-- Corrugated:

30 1.5 mm or less in thickness 7210 41 910 7210.41.10 90, 7210.41.20 00

Hot Dip Zinc Coated Sheet and Coil

MS 606

-- Other:

31 1.5 mm or less in thickness 7210 49 910 7210.49.20 00 Hot Dip Zinc Coated Sheet and Coil

MS 606

32 Other 7210 49 990 7210.49.10 90, 7210.49.90 90

-- Plated or coated with aluminium-zinc alloys:

Corrugated:

33 1.5 mm or less in thickness 7210 61 210 7210.61.10 10 Hot Dip Zinc Coated Sheet and Coil

MS 1196:2004

34 more than 1.5 mm in thickness 7210 61 220 7210.61.90 12

35 1.5 mm or less in thickness 7210 61 921 7210.61.10 90


- Painted, varnished or coated with plastics:

37 1.5 mm or less in thickness 7210 70 910 7210.70.10 00 Hot Dip Zinc Coated Steel Sheet and Coil Aluminium-zinc Alloy-coated Steel Sheet in Coil

JIS G 3312 JIS G 3322


of 16

Flat rolled products of iron or

non-alloy steel, of a width of less than 600 mm, not clad, plated or coated

7211

- Not further worked than hot rolled:

-- Rolled on four faces or in a close box pass, of a width exceeding 150 mm and a thickness of not less than 4 mm, not in coils and without patterns in relief:

39 universal plates 7211 13 910 7211.13.90 12 Steel Strip and Sheet MS 1705:2003

40 exceeding 150 mm but not exceeding 400 mm in width

7211 13 921 7211.13.10 90

41 other 7211 13 929 7211.13.90 22

-- Other, of thickness of 4.75 mm or more:

42 universal plates 7211 14 910 7211.14.90 12 Pipes and Tubes MS 1768:2004

43 not exceeding 25 mm in width 7211 14 921 7211.14.10 21


7211 14 922 7211.14.10 22

45 other 7211 14 929 7211.14.90 22

46 coils for re-rolling 7211 14 930 7211.14.90 30 SAE J 403:2009

47 other 7211 14 990 7211.14.90 99 Steel Strip and Sheet MS 1705:2003

-- Other:

Containing by weight 0.6% or more of carbon:

Hoop and strip:

48 not exceeding 25 mm in width 7211 19 911 7211.19.10 21 Pipes and Tubes MS 1768:2004


7211 19 912 7211.19.10 22

50 other 7211 19 919 7211.19.90 12

51 coils for re-rolling 7211 19 920 7211.19.90 30

52 of a thickness of 0.17 mm or less

7211 19 991 7211.19.30 90

53 other 7211 19 999 7211.19.90 99

- Not further worked than cold-rolled (cold-reduced):

-- Containing by weight less than 0.25% of carbon:

Hoop and strip:

54 not exceeding 25 mm in width 7211 23 110 7211.23.20 10 Steel Strip MS ISO 6932:2009 55 exceeding 25 mm but not more

than 400 mm in width 7211 23 120 7211.23.20 20

56 other 7211 23 190 7211.23.90 10


7211 23 910 7211.23.30 00

58 other 7211 23 990 7211.23.90 90

of 16

-- Other:

Containing by weight 0.25% or more but less than 0.6% of carbon:

Hoop and strip:

59 not exceeding 25 mm in width 7211 29 111 7211.29.20 11 Steel Strip MS ISO 4960:2009 60 exceeding 25 mm but not

exceeding 400 mm in width 7211 29 112 7211.29.20 12

61 other 7211 29 119 7211.29.90 11


7211 29 191 7211.29.30 10

63 other 7211 29 199 7211.29.90 91

64 not exceeding 25 mm in width 7211 29 211 7211.29.20 21


7211 29 212 7211.29.20 22

66 other 7211 29 219 7211.29.90 12

67 other 7211 29 290 7211.29.10 20, 7211.29.30 20, 7211.29.90 99

Flat-rolled products of iron or non-alloy steel, of a width of less than 600 mm, not clad, plated or coated

7212

- Electrolytically plated or coated with zinc:

68 not exceeding 25 mm in width 7212 20 911 7212.20.10 21 Steel Sheet MS ISO 5002:2009 69 exceeding 25 mm but not

exceeding 400 mm in width 7212 20 912 7212.20.10 22

70 other 7212 20 919 7212.20.90 22


72 other 7212 20 999 7212.20.90 99

- Otherwise plated or coated with zinc:

73 not exceeding 25 mm in width 7212 30 911 7212.30.10 21 Hot Dip Zinc Coated Sheet in Coil

MS 606

74 exceeding 25 mm but not more than 400 mm in width

7212 30 912 7212.30.10 22

75 other 7212 30 919 7212.30.90 22


77 other 7212 30 999 7212.30.90 99

- Painted, varnished or coated with plastics:

78 not exceeding 25 mm in width 7212 40 911 7212.40.10 21 Hot Dip Zinc Coated Steel Sheets and Coils

JIS G 3312


7212 40 912 7212.40.10 22

80 other 7212 40 919 7212.40.90 22

81 1.5 mm or less in thickness 7212 40 991 7212.40.20 00 Aluminium-zinc Alloy-coated Steel Sheet and Coil

JIS G 3322


of 16

- Otherwise plated or coated:

83 not exceeding 25 mm in width 7212 50 911 7212.50.10 21 Hot Dip Zinc Coated Steel Sheets and Coils

MS 1196:2004

84 exceeding 25 mm but not more than 400 mm in width

7212 50 912 7212.50.10 22

85 other 7212 50 919 7212.50.90 22



Bars and rods, hot-rolled, in irregularly wound coils, of iron or non-alloy steel

7213

88 - Containing indentations, ribs, grooves or other deformations produced during the rolling process

7213 10 000 7213.10.00 00 Hot Rolled Steel Reinforcement Bar

MS 146:2006

89 - Other, of free-cutting steel 7213 20 000 7213.20.00 00 Free Cutting Steel MS 1495

90 - - Of circular cross section measuring less than 14 mm in diameter

7213 91 000 7213.91.00 00 Steel Wire Rod MS ISO 16120: Part 1 & 2

91 - - Other 7213 99 000 7213.99.00 00 MS ISO 16120: Part 3 MS ISO 16120: Part 4

Other bars and rods of iron or non-alloy steel, not further worked than forged, hot-rolled, hot-drawn or hot-extruded, but including those twisted after rolling

7214

- Forged:

92 round 7214 10 110 7214.10.21 00 Carbon Steel for Structural Machine Use

MS 2247:2009

93 round 7214 10 910 7214.10.11 00 Hot Rolled Steel Reinforcement Bar

MS 146:2006

94 other 7214 10 990 7214.10.19 00 Carbon Steel for Structural Machine Use

MS 2247:2009

-Containing indentations, ribs, grooves or other deformations produced during the rolling process or twisted after rolling:


MS 2246:2009

96 round 7214 20 910 7214.20.11 00 Hot Rolled Steel Reinforcement Bar

MS 146:2006

- Of free-cutting steel:

97 Round 7214 30 100 7214.30.00 10 Free Cutting Steel MS 1495

of 16

-- Other:


MS 2247:2009

99 round 7214 99 910 7214.99.90 21 Structural Steel MS EN 10025:2009 MS 2247:2009

Other bars and rods of iron or non-alloy steel

7215

- Of free-cutting steel, not further worked than cold-formed or cold-finished:

100 Round 7215 10 100 7215.10.00 10 Free Cutting Steel MS 1495

- Other, not further worked than cold-formed or cold-finished:

101 round 7215 50

110

7215.50.90 10 PC Strand MS 1138: Part 1 – 4:2007

102 round 7215 50

910

7215.50.90 20

- Other:

103 Round 7215 90 100 7215.90.00 10 PC Strand MS 1138: Part 1 – 4:2007

Angles, shapes and sections of iron or non-alloy steel

7216

- U, I or H sections, not further worked than hot-rolled, hot-drawn or extruded, of height of less than 80 mm:

104 of a thickness of 5 mm or less 7216 10 100 7216.10.00 10 Structural Steel and Sheet Pile

MS 1490 MS 1491 105 other 7216 10 900 7216.10.00 90

- L or T sections, not further worked than hot-rolled, hot-drawn or extruded, of height of less than 80 mm:

-- L sections:

106 Other 7216 21 900 7216.21.00 90 Structural Steel and Sheet Pile

MS 1490 MS 1491

-- T sections:


MS 1490 MS 1491 108 other 7216 22 900 7216.22.00 90

- U, I or H sections, not further worked than hot-rolled, hot-drawn or extruded, of height of 80 mm or more:

-- U sections:

109 of a thickness 5 mm or less 7216 31 100 7216.31.00 10 Structural Steel and Sheet Pile

MS 1490 MS 1491 110 other 7216 31 900 7216.31.00 90

-- I sections:


MS 1490 MS 1491 112 other 7216 32 900 7216.32.00 90

of 16

-- H sections:

113 Containing by weight 0.6 % or more carbon

7216 33 100 7216.33.00 10 Structural Steel and Sheet Pile

MS 1490 MS 1491

114 thickness of web of 9 mm and above

7216 33 911 7216.33.00 21

115 other 7216 33 919 7216.33.00 22

- L or T sections, not further worked than hot-rolled, hot-drawn or extruded, of height of 80 mm or more:

116 L section 7216 40 100 7216.40.00 10 Structural Steel and Sheet Pile

MS 1490 MS 1491 117 of a thickness of 5 mm or less 7216 40 910 7216.40.00 21

118 other, T sections 7216 40 990 7216.40.00 29

- Other angles, shapes and sections, not further worked than hot-rolled, hot-drawn or extruded:

Angles, other than slotted angles:

119 of a height of 80 mm or more 7216 50 191 7216.50.90 12 Structural Steel and Sheet Pile

MS 1490 MS 1491 120 of a height of less than 80 mm 7216 50 192 7216.50.10 12

121 of a thickness of 5 mm or less 7216 50 211 7216.50.10 21

122 other 7216 50 219 7216.50.10 29

123 of a thickness of 5 mm or less 7216 50 221 7216.50.90 21

124 other 7216 50 229 7216.50.90 29

- Angles, shapes and sections, not further worked than cold-formed or cold-finished:

-- Obtained from flat-rolled products:


125 of a height of 80mm or more 7216 61 191 7216.61.00 13 Structural Steel and H Pile

MS 2259:2009

126 of a height of less than 80 mm 7216 61 192 7216.61.00 14

127 of a thickness of 5 mm or less 7216 61 211 7216.61.00 21 MS 1490 MS 1491 128 other, shapes and sections 7216 61 219 7216.61.00 29

-- Other:


129 of a thickness of 5 mm or less 7216 69 211 7216.69.00 21 Structural Steel and H Pile

MS 2259:2009

130 other, shapes and sections 7216 69 219 7216.69.00 29

Wire of iron and non-alloy steel

7217

131 - Not plated or coated, whether or not polished

7217 10 000 7217.10.10 00, 7217.10.22 00, 7217.10.29 00, 7217.10.31 00, 7217.10.39 00

MS 1137 MS 144

132 - Plated or coated with zinc 7217 20 000 7217.20.10 00, 7217.20.20 00, 7217.20.91 00, 7217.20.99 00

MS 1238 MS 1239 MS 1240

133 - Plated or coated with other base metals

7217 30 000 7217.30.10 00, 7217.30.20 00, 7217.30.31 00, 7217.30.39 00

MS ISO 16650:2009

134 - Other 7217 90 000 7217.90.00 00 Steel Wire and Fabric ASTM A 933

of 16

Other bars and rods of

stainless steel; angles, shapes and sections of stainless steel

7222

- Bars and rods, not further worked than cold-formed or cold-finished:

135 Round 7222 20 100 7222.20.10 00 MS 2240-2

- Other bars and rods:

136 Round 7222 30 100 7222.30.10 00

Other bars and rods of alloy steel; angles, shapes and sections, of other alloy steel; hollow drill bars and rods, of alloy or non-alloy steel

7228

- Angles, shapes and sections:

137 of a height of 80 mm or more 7228 70 110 7228.70.00 11

138 of a height of less than 80 mm 7228 70 120 7228.70.00 12

139 of a thickness of 5 mm or less 7228 70 211 7228.70.00 21 Structural Steel and H Pile

MS 1490 MS 1491

Wire of other alloy steel 7229

- Of silico-manganese steel:

140 Other 7229 20 900 7229.20.00 90 PC Strand MS 1138: Part 1 – 4:2007

Sheet piling of iron and steel, whether or not drilled, punched or made from assembled elements, welded angles, shapes and sections, of iron or steel

7301

141 - Sheet piling 7301 10 000 7301.10.00 00

Sheet Pile MS 2025-1 MS 2025-2

142 - Angles, shapes and sections 7301 20 000 7301.20.00 00

Structural Steel and H Pile

MS 1490 MS 1491

Railway or tramway track construction material of iron or steel

7302

143 - Rails

7302 10 000 7302.10.00 00 Steel Rails Light Rail Crane Rail

BS 11 AS 1085.1 & 2 JIS E 1103 DIN 536

144 Sleepers (cross-ties) 7302 90 100 7302.90.10 00

Tubes, pipes and hollow profiles of cast iron

7303

145 Tubes, pipes and hollow profiles, of cast iron.

7303 00 000 7303.00.10 00, 7303.00.90 00

Ductile Iron Pipes, Fittings, Accessories

BS EN 545:2006 BS EN 598:2007

of 16

Tubes, pipes and hollow

profiles, seamless, of iron (other than cast iron) or steel

7304

- Line pipe of a kind used for oil or gas pipelines:

146 - - Of stainless steel 7304 11 000 7304.11.00 00 Boiler, Super Heater, Heat Exchange Tubes

ASTM/SA 213

Condenser Tube ASTM A249

Stainless Steel Pipe ASTM 312 ASTM A358 ASTM A376 ASTM A409 ASTM A813

147 - - Other 7304 19 000 7304.19.00 00 Steel Pipe ASTM A53


Carbon Steel Pipe ASTM A106

Steel Pipe ASTM A333

Carbon Steel Pipe ASTM A106

Steel Boiler and Super Heater Tubes

ASTM A210

148 - - Drill pipe of stainless steel 7304 22 000 7304.22.00 00 Boiler, Super Heater, and Heater Exchanger

ASTM/SA 213

149 - - Other drill pipe 7304 23 000 7304.23.00 00

150 - - Other, of stainless steel 7304 24 000 7304.24.00 00 Condenser Tubes ASTM A249

151 - - Other 7304 29 000 7304.29.00 00 Stainless Steel Pipes ASTM 312

- Other, of circular cross-section, of iron or non-alloy steel:

-- Cold-drawn or cold-rolled (cold-reduced):

152 High pressure hydro-electric conduits

7304 31 100 7304.31.10 10, 7304.31.90 10

ASTM A358

153 Other 7304 31 900 7304.31.10 90, 7304.31.90 90

ASTM A376

-- Other:


7304 39 100 7304.39.00 10 ASTM A409

155 Other 7304 39 900 7304.39.00 90 ASTM A813

- Other, of circular cross-section, of stainless steel:



7304 41 100 7304.41.00 10 Boiler, Super Heater, and Heater Exchanger Tubes

ASTM/SA 213

157 Other 7304 41 900 7304.41.00 90 Condenser Tubes

ASTM A249

-- Other:


7304 49 100 7304.49.00 10 Stainless Steel Pipes ASTM 312

159 Other 7304 49 900 7304.49.00 90 ASTM A358

- Other, of circular cross-section, of other alloy steel:



7304 51 100 7304.51.10 10, 7304.51.90 10

ASTM A376

161 Other 7304 51 900 7304.51.10 90, 7304.51.90 90

ASTM A409

of 16

-- Other:


7304 59 100 7304.59.00 10 ASTM A813

163 Other 7304 59 900 7304.59.00 90

- Other:


7304 90 100 7304.90.00 10

Other tubes and pipes (e.g. welded, riveted or similarly closed), having circular cross-sections, the external diameter of which exceeds 406.4 mm, of iron or steel

7305

165 - - Longitudinally submerged arc welded

7305 11 000 7305.11.00 00 Tubes and Pipes MS ISO 3183

166 - - Other, longitudinally welded 7305 12 000 7305.12.00 00

167 - - Other 7305 19 000 7305.19.00 00

168 - Casing of a kind used in drilling for oil or gas

7305 20 000 7305.20.00 00 Casing Tubes API 5CT

169 - - Longitudinally welded 7305 31 000 7305.31.10 00, 7305.31.90 00

Boiler, Super Heater and Heat Exchanger Tubes

ASTM/SA 213

Stainless Steel Pipes ASTM 312 ASTM A376 ASTM A333 ASTM A53 ASTM A135

170 - - Other 7305 39 000 7305.39.00 00 Non-alloy Steel Tube and Fittings

MS 1968:2007

171 - Other 7305 90 000 7305.90.00 00 Non-alloy Steel Tube and Fittings

MS 1968 MS 1862

Other tubes, pipes and hollow profiles (e.g. open seam or welded, riveted or similarly closed), of iron or steel

7306

172 - - Welded, of stainless steel 7306 11 000 7306.11.00 00 Seamless Pipe Boiler, Super Heater and Heat Exchanger Tubes Stainless Steel Pipes

API 5L ASTM/SA 213 ASTM 312 ASTM A376 ASTM A333 ASTM A53 ASTM A135

173 - - Other 7306 19 000 7306.19.00 00

174 - - Welded, of stainless steel 7306 21 000 7306.21.00 00 Stainless Steel Pipes MS 1841

175 - Other, welded, of circular cross section, of iron or non-alloy steel

7306 30 000 7306.30.10 00, 7306.30.20 00, 7306.30.30 00, 7306.30.90 00

Carbon Steel Tubes Welded Steel Pipes

MS 1862 MS 1968 MS 863:2004

176 - Other, welded, of circular cross-section, of stainless steel

7306 40 000 7306.40.10 00, 7306.40.20 00, 7306.40.30 00, 7306.40.90 00

Stainless Steel Pipes JIS G3459

ASTM 312 SUS 304 SUS 316 SUS 317 SUS 321

of 16

177 - Other, welded, of circular cross-section, of other alloy steel

7306 50 000 7306.50.10 00, 7306.50.90 00

Carbon Steel Tubes MS 1862

178 - - Of square or rectangular cross-section

7306 61 000 7306.61.00 00

179 - - Of other non-circular cross-section

7306 69 000 7306.69.00 00

180 - Other 7306 90 000 7306.90.10 00, 7306.90.90 00

Non-alloy Steel and Tubes and Fittings

MS 1968 MS 863:2004 MS 275

Structures (Bridges, towers, doors, windows, scaffoldings)

7308

- Equipment for scaffolding, shuttering, propping or pit-propping:

181 Other 7308 40 900 7308.40.10 90, 7308.40.90 90

Tube for Scaffolding MS 1462

Stranded wire, ropes, cables, plaited, bands, slings and the like, of iron or steel, not electrically insulated

7312

182 - Stranded wire, ropes and cables

7312 10 000 7312.10.10 00, 7312.10.20 00, 7312.10.40 00, 7312.10.90 00

Wire Ropes and Wire Strand, Wire Cable Single Wire for Wire Strand, Wire Cable

MS ISO 2408 MS 551 MS 552 MS ISO 4344 BS EN 13414-1 BS EN 13414-2 BS EN 13414-3

183 - Other 7312 90 000 7312.90.00 00

Cloth (including endless bands), grill, netting and fencing, expanded metal of iron or steel

7314

184 - Grill, netting and fencing, welded at the intersection, of wire with a maximum cross-sectional dimension of 3 mm or more and having a mesh size of 100 cm2 or more

7314 20 000 7314.20.00 00 Steel Fabric, Mesh for Fencing

MS 145

185 - Expanded metal 7314 50 000 7314.50.00 00 Steel Grating BS 405

Other cast articles of iron and steel

7325

- Of non-malleable cast iron:

186 Manhole covers, gratings and frames thereof

7325 10 100 7325.10.90 10 Manhole Tops and Gully

BS EN 124:1994

-- Other:

187 Manhole covers, gratings and frames thereof

7325 99 100 7325.99.90 10

appendix iv tariff codes - mytradelink...page 6 of 16 19 - other 7208 54 990 7208.54.00 99 plates,...

Documents