aocp spec
TRANSCRIPT
-
7/25/2019 aocp spec
1/11
Name of Item: Variable Capacitance type Level Indicator
Specification:
Electronic Level Transmitter:Service: Water
Measuring Principle: Capacitance type
Range: 0500 mm WC
Accuracy: +/- 3 %
Output: 4-20 mA DC
Probe: fully insulated rod probe with preamplifier
Mounted on probe head generates RF signal and converts detected capacitance signal to current Signal.
Sump Tank:
Service : Water
Capacity : 80 liters
MOC : SS-304Pump:
Voltage : 220 V AC
Power : HP
Measuring Tank:
Service : Water
Capacity : 30 liters
MOC : Transparent Acrylic
Range : 0500 mm WC
Necessary piping and fittings should be provided.
The setup should be mounted on MS structure having good quality paint.
-
7/25/2019 aocp spec
2/11
Name of Item:RTD Resistance-bulb Wheatstone Bridge Thermometers
Specification:
Resistance Bulb Thermometer: Pt
100Accuracy: Class A
Insulation: Mineral insulated
Terminal Block: 4 wire termination in ceramic terminal
Block provided in cast Aluminium Block
Length: 200 mm
The construction drawing, Temperature Vs Resistance Table & calibration Checking procedure along with
portable wheatstone bridge (having inbuilt Galvanometer & battery) to measure resistance of Resistance
Bulb Thermometer having measurement accuracy + 0.075 %.
Portable Wheatstnebridge
This set should be designed to provide an accurate and sensitive instrument of resistance and locating
faults in cables by adopting the Varley Loop Circuit for tests. This set should be entirely self-contained witha dry battery and a Galvanometer. The instrument should be equipped with another switch controlling the
sensitivity or short-circuiting the galvanometer. Arrangement should be provided to use the extra
galvanometer or high source voltage for increasing the sensitivity of the bridge.
Range: 0.001 ohm to 11, 11 megohms.
Series Arm: Four decades in steps of thousands, tens and units ohms using manganian coil which can be
used as a series resistance box also with + 0.1% accuracy
Ratio Arms: The ratio arm of bridge are to be capable of selecting
multiplying factors of 0.001, 0.01, 1, 10, 100 and 1000 for
conductive resistance measurements and for varley loop test
Null Detector
Galvanometer: Ri 20 ohms, 1mm/ A sensitivityBattaery: 3 cell of 1.5 V, R 20 size
-
7/25/2019 aocp spec
3/11
Name of Item: Apparatus for determination of flash point
Specification:
This apparatus is made as per IP 34, ASTMD-93 and IS 1448 (Part I) 1270 (P.21) and IS 1209-1953 methodB. It is used for finding out flash point above 70C and below 300C. The instrument having oil test jet/Gas
test jet flame device, stirrer with flexible shaft. The assembly rests in air bath which is covered with dome
shape metal top. The cup is fitted with insulated handle and locking Arrangement near cup flange. The
assemble is kept on round shape electric heater with separate temp. Regulator.
Suitable for operation on 220 volts 50 cycles Ac circuits.
P.M. flash point apparatus electric heated with energy regulator oil test jet.
-
7/25/2019 aocp spec
4/11
Name of Item:Sparkler Filters
Specification:
Sparkler Filters Zero Hold up models in M.O.C. SS-304, 316, 316L and optional with PP, halar,PTFE (PFA), PVDF coating/lining on all wetted parts. 8, 14, 18, 24 and 33 sizes with n no. of
plates. Complete filtrations of batch without any holdup of unfiltered liquid. GMP model with
complete unit mounted on SS trolley. Back wash facility for cleaning the filter without opening the
assembly. SS 304 Jacket for hot filtration, Flameproof Motor, Sight Glass on outlet offered on
request. Ideal for filtration in sugar, beverage, pharmaceuticals, chemicals, dyes, edible and non-
edible oils, resins, paints, perfumes, activated carbonetc. The cake, filter aid and solids remain
totally enclosed allowing filtration of toxic, hazardous and explosive liquids. The top dome
structure ensures fast and easy removal of cartridge assembly and cleaning of cake.
-
7/25/2019 aocp spec
5/11
Name of Item:Leaf Filters
Specification:
Pressure Leaf Filters 1-100m2 filtration area offered in vertical and horizontal models. Stainlesssteel filter elements, hence no repetitive cost, washing and maintenance of filter cloth. Filtration
rates are 2-3 times higher on same filter area of plate and frame type filter. Automatic cake
discharge with mechanical or pneumatic vibrator and optional spray nozzle for wet cake discharge.
Ideal replacement for plate and frame filter. Closed system, no maintenance due to SS filtration
mesh, low retention of oil, less occupancy of space etc. Very low % of unfiltered liquid retention in
cake. Simple and economical bottom opening with 100% opening and optional butterfly valve for
vertical PLF Closed pressurized operating system hence no spillage and loss of liquid, which helps
in handling volatile / inflammable liquids and clean working environment. Pressure leaf filter can
be completely automated with no human intervention.
-
7/25/2019 aocp spec
6/11
Name of Item:Apparatus for determine Frictional losses in straight pipe, pipe fitting
Specification:
RANGE OF EXPERIMENT:-To determine the friction factor (major losses) for Darcy Weisbach equation.
SPECIFICATION:- Block Type Acrylic Differential Manometer (250-0-250 mm) Flow control valve to change Discharge. Two Pipes (Length of pipe between two pressure tapings 1 mtr.)
A. Dia. of pipe - 0.022 m (For pipe )B. Dia. of pipe - 0.016 m (For pipe )
Transparent pizometer tube with scale to measuremeasuring tank discharge. Measuring tank- 295 X 345 X 345 mm Sump tank- 900 X 350 X 350 mm Greaves motor for recalculating type unit.- 0.5H.P. Self-Priming Stop clock.
SERVICE REQUIRED:- Suitable Water supply. Suitable floor space to mount apparatus. 15 amps Single Phase Electrical Connection.
-
7/25/2019 aocp spec
7/11
Name of Item:Evaporator rising falling film evaporator
Specification:
Stainless steel industrial vapor liquid separator.
Shell is rated for vacuum 400 F. Vapor liquid separator has a 50" straight side, an 18"
cone, and a 22" diameter.
Separator has a 4" diameter flanged liquid discharge, a 10" diameter flanged steam inlet,
and a 6" diameter flanged steam outlet.
The separator has a 16" diameter hatch with a 6" diameter sight glass on the side and a 6"
diameter sight glass on top.
The flange on the top sight glass is broken and the hinge to top opening is bent
Name of Item:Triple effect evaporator
Specification:
Tech Data:
Three-effect falling film evaporator
Rated evaporation: 50L / h
Installed power: ~ 6,05KW
feed temperature: room temperature, the material temperature
-
7/25/2019 aocp spec
8/11
Name of Item:Sieve plate distillation column.
Specification:
Materialstainless steel 304
TemperatureRoom temp~260(Electric heating included)
Column sizeDN50*1200mm
InternalsSieve tray columns.
Reboiler10L or 20L
Receiversize&quantity
10L*2
Condenser HTA
0.86 (m2)
Vacuity
MIN:10mbar(depend on the nature of material and vacuum pump& vacuum pump not included)
Floor arealength*width*height=1000*800*2700 (mm)(without vacuum pump)
Power
4KW (without pump)
Estimated Cost:Prepared By:
-
7/25/2019 aocp spec
9/11
Name of Item:Batch type tank crystallizer
Specification:
The setup consists of an open, jacketed and conical bottom vessel fitted with a low RPM
agitator and a heater. Arrangement for Cooling water circulation and flow measurement in
jacket is made by using storage type water tank, a pump and a rotameter.
The feed/mother liquor is prepared in the crystallizer vessel itself using heater and stirrer.
The hot super saturation solution in the crystallizer is then cooled by circulation of cooling
water and crystals are formed. Necessary instrumentation is done for temp measurement
Features
Superb Painted structure
Simple to operate & maintain
Compact & stand alone set up
Utilities Required
Electric supply Provide 230 +/- 10 VAC, 50 Hz, single phase electric supply with proper
earthing. 5A, three pin socket with switch for weighing scale, 15A, three pin socket with
switch for heater
-
7/25/2019 aocp spec
10/11
Name of Item:Mechanical seal (multiple spring)
Specification:
Specifications:
Shaft diameter: 1/2" to 6"
Pressure Unbalanced: Vacuum to 10 bar
Pressure Balanced: Vacuum to 35 bar
Speed: Up to 2900 rpm
Temperature: -50 oC to + 300 oC
-
7/25/2019 aocp spec
11/11
Name of Item:pump cut model
Specification:
Specifications:
Sectioning of an actual ANSI pump. (A Goulds-brand pump is used in the circumstance).
Cleaning, priming and painting using a high-durability urethane coating.
Color-coding of cutaway surfaces, seat and closurel elements, impeller and exterior
surfaces using contrasting colors.
Replacement, plated hardware, where necessary.
All gaskets, seals and bearings visible.
7-Gauge, formed-steel, powder-coated, baseplate, with provision for tabletop mounting andmounting on related workstation and storage products.
Crating for shipment via motor freight.