annexure-ii-list of codes & standards

15 Pune Mumbai Road, Sai Chambers, Wakdewadi Pune - 411003 Contact No. - +91-020-66414000

TECHNICAL BID FOR 1 x 6.5MW(Net) POWER PLANT

AT (INDONESIA)) POWER DIVISION

Project Name Proposal No. Revision No. Date Sect Page No.

ACE PROJECT E-0110 0 20-03-2015 Annex-II Page 1 of 25

ANNEXURE-II LIST OF CODES AND STANDARDS

Sr. No.

Codes/Norm (International standards)

Description Codes/Norms/ Standard

(as practiced by Thermax Ltd.)

1. Relevant Indian Standards For structural steelwork design IS:800

2.

Design & Environmental Guidelines required by International Finance

Corporation (IFC), World Bank Group,

Washington , D.C., U.S.A.

World Bank Norms (2008 version) (referred only as

guideline)

3. Industry Standards For terminal blocks IEC 60947-7-1

4. AGMA 2001, B88 For gearing AGMA 6011 I03

5. API 650/ASME Diesel Fuel Storage Tank SAME OR IS 803

6. Relevant ASME Codes For emergency boiler feed systems Relevant ASME Codes

7. Relevant ASME Codes To calculate total head of boiler feed

pumps Relevant ASME Codes

8. Relevant ASME Codes For emergency feed pump system &

to calculate total head

9. OSHA's standard For silencers provided for the

superheater safety valve & start up vent valve

OSHA's standard






Sr. No.




10. Indian Standards For gallery and stairway equipment Indian Standards

11. OSHA's standard Silencer to reduce relief valve noise. OSHA's standard

12.

American Boiler Manufacturer's Association (ABMA/BS. 2486 for a

boiler operating at 48 kg/cm2 a/430 deg C (668 PSIG/806 deg F)

For quality of boiler feed water IS 10392, BS 2486

13. API 650/ASME For boiler feed water storage tank. HEI & ASME VIII

14. American Crane Manufacturers

Association For Electric Operated Overhead

Travelling Bridge Crane IS:3177

15. API 650/ASME For clarified water storage tank IS 803

16. ASME Code Vessel for air receiver ASME VIII, IS:7938/2825

17. ASME B31.3 ASME B31.1

For piping fabrication, installation, inspection & testing

ASME B31.3 ASME B31.1

18. AWS Regulations, ASME B31.3 For welding procedures AS PER IBR OR ASME 31.1

19. AWS & Section IX of the ASME Boiler

and Pressure Vessel Code Welder's qualifications

AWS & Section IX of the ASME Boiler and Pressure

Vessel Code

20. ANSI B31.3 Pipe fabrication required for piping

work ANSI B31.3






Sr. No.




21. ASME B31.3 Flange ratings and facings, bolts,

and gaskets B 16.5

22. EJMA 4th Edition Tolerances for dents & scratches EJMA 4th Edition

23. ASME B31.3 Bevelled ends for butt welded joints ASME B31.3 & B31.3

24. ASME B31.3 Branch connections ASME B31.3 & B31.3

25. ANSI B2 Threaded connections ANSI B2

26. OSHA regulation Field routed piping Relevant IS Code

27. Intergranular Corrosion test specified

in Section 12 of ASTM A 240 Relevant IS Code

28. ASTM A 380 Descaling and cleaning of entire

assembly ASTM A 380

29. ASME B31.3 Code for Pressure Piping For welded connections ASME B31.1 Code for POWER PIPING

30. ASME B31.3 for carbon steel piping PWHT is to be performed IBR & ASME B31.1

31. Code for Pressure Piping ASME

B31.3,"Chemical Plant and Petroleum

Refinery Piping"

For radiography if required IBR & ASME B31.1






Sr. No.




32. ANSI B31.3 or ANSI B31.1 Weldment Inspection IBR & ASME B31.1

33. ASME B31.3 Relevant Post-weld procedures IBR & ASME B31.2

34. ASTM C 552 For insulation IS 14164 / 8183 / 4671

35. ASTM D1557 (Modified Proctor) Soil density tests IS 2720

36. ACI 214 - Recommended Practice for Evaluation of Strength Test Results of

Concrete Cast-in-place Concrete IS:516-1959

37. ACI 301 - Specifications for Structural

Concrete for Buildings Cast-in-place Concrete IS 456:2000

38. ACI 302.1 - Guide for Concrete Floor

and Slab Construction Cast-in-place Concrete IS 2571 : 1970

39. ACI 304 - Guide for Measuring, Mixing,

Transporting and Placing Concrete Cast-in-place Concrete IS 6461 : 1973

40. ACI 305 - Hot Weather Concreting Cast-in-place Concrete IS 7861 (Part-1)

41. ACI 306 - Cold Weather Concreting Cast-in-place Concrete IS 7861 (Part-2)

42. ACI 308 - Standard Practice for Curing

Concrete Cast-in-place Concrete IS 6461 : 1973






Sr. No.




43. ACI 309 - Guide for Consolidation of

Concrete Cast-in-place Concrete IS 7246: 1974

44. ACI 318 - Building Code Requirements

for Structural Concrete Cast-in-place Concrete IS 456:2000

45. ASTM C31 - Standard Practice for Making and Curing Concrete Test

Specimens in the Field Cast-in-place Concrete IS 6461 : 1973

46. ASTM C33 - Standard Specification for

Concrete Aggregates Cast-in-place Concrete IS 383:1970

47. ASTM C39 - Standard Test Method for Compressive Strength of Cylindrical

Concrete Specimens Cast-in-place Concrete IS 516:1959

48. ASTM C94 - Standard Specimen for

Ready-Mixed Concrete Cast-in-place Concrete IS 4926 : 2003

49. ASTM C138 - Standard Test Method for

Unit Weight, Yield, and Air Content (Gravimetric) of Concrete

Cast-in-place Concrete IS 516:1959


Slump of Hydraulic Cement Concrete Cast-in-place Concrete IS 4031: 1996

51. ASTM C150 - Standard Specification

for Portland Cement Cast-in-place Concrete IS 8112

52. ASTM C172 - Standard Practice for Sampling Freshly Mixed Concrete

Cast-in-place Concrete IS 1199:1959

53. ASTM C173 - Standard Test Method for Air Content of Freshly Mixed Concrete

by the Volumetric Method Cast-in-place Concrete IS 7325 : 1974






Sr. No.




54. ASTM C230 - Standard Specification

for Flow Table or Use in Tests of Hydraulic Cement

Cast-in-place Concrete IS 4031 : 1996

55.

ASTM C260 - Standard Specification

for Air-Entraining Admixtures for Concrete


56. ASTM C494 - Standard Specification for Chemical Admixtures for Concrete


57.

ASTM C618 - Standard Specification for Fly Ash and Raw or Calcined

Natural Pozzolan for Use as a Mineral

Admixture in Portland Cement Concrete

Cast-in-place Concrete

Relevant Indian standard code 58.

ASTM E1155 - Standard Test Method for Determining Floor Flatness and

Levelness Using the F-Number System Cast-in-place Concrete

59.

ASTM C1315 - Standard Specification

for Liquid Membrane-Forming Compounds Having Special Properties

for Curing and Sealing Concrete

Cast-in-place Concrete

60. ACI 318, Chapter 5 Concrete mix design proportions IS: 10262

61. ASTM Relevant Indian standard code

62. ASTM C150, Type I Portland Cement IS 8112






Sr. No.




63. ASTM C33 Fine aggregate & Coarse aggregate of

gravel or crushed stone IS 383:1970

64. ACI 318 Size coarse aggregate IS 456:2000

65. ACI 318 Water IS 6461 : 1973

66. ASTM C260 Air Entraining Agent IS 6461 : 1973

67. ASTM C494 High-range water reducer IS 6461 : 1973

68. ASTM C1315 Curing Compound IS 6461 : 1973

69. ASTM C618 Fly ash IS 6461 : 1973

70. ASTM C494 Accelerators IS 6461 : 1973

71. ASTM C494 Retarders IS 6461 : 1973

72. ACI 302 Placing of floors and slabs IS 2571 : 1970

73. ACI 301, ACI 304 and ACI 318 IS 456:2000

74. ACI 301 and ACI 309 IS 456:2000






Sr. No.




75. ACI 308 Curing of Concrete IS 6461 : 1973

76. ACI 306 and ACI 308 Curing in cold weather IS 6461 : 1973

77. ACI 301 Finishing of Concrete IS 456:2000

78. ACI 306 Cold weather concreting IS 7861 : Part 2 : 1975

79. ACI 305 Hot weather concreting IS 7861 : Part 1 : 1975

80.

ASTM Specifications D-2241 and D-

1784 with SDR of 26 NSF Approved

AWWA C-900 standards

PVC Pipes IS 4985 : 2000

81.

AWWA C906

ASTM D3350 cell classification of 345434C

HDPE Pipe IS 4984 : 1995

82. AWWA Specifications Standard C-500

AWWA Standards for potable water use Valves As per relevant standards

83. AWWA Standard C-110 Fittings As per relevant standards

84. USA Department of Transportation

Specifications Road & Swale grading Indian road congress (IRC)

85. AASHO-T180 (modified Proctor) Backfill IS 2720






Sr. No.




86. ASTM Specification No. D-3034 Pipes and fittings As per relevant standards

87. ASTM Specification C-12 Crushed Rock IS 383:1970

88. ASTM Specifications C-14 and C-478 Material of manholes IS 12592 : 2002, IS 1726 : 1991

89. U.S. Foundry No. 604-Au-ORS, traffic

bearing Covers for manholes IS 12592 : 2002, IS 1726 : 1991

90. ASTM Specifications C-14 and C-478 Wet well Relevant Indian standard code

91. ASTM Specification A-20 GI Pipe IS 4736

92. AWWA Standard C-500 Gate Valve As per relevant standards

93. ASTM Class 60 Steel casing IS 2062

94. ACI 117 - Standard Specifications for Tolerances for Concrete Construction

and Materials Concrete Formwork IS 456:2000


Concrete for Buildings Concrete Formwork

IS 456:2000


for Structural Concrete Concrete Formwork






Sr. No.




97. ACI 347 - Recommended Practice for

Concrete Formwork Concrete Formwork IS 6461 : Part 5 : 1972

98.

ASTM D1751 - Standard Specification for Preformed Expansion Joint Filler for Concrete Paving and Structural Construction (Non-extruding and

Resilient Bituminous Types)

Concrete Formwork IS 1838 : Part 1 : 1983

99.

ASTM E154 - Standard Test Methods for Water Vapor Retarders used in contact with earth under concrete

slabs, on walls, or as Ground Cover

Concrete Formwork Relevant Indian standard code

100. ACI 117, ACI 301, ACI 318 and ACI

347 Design of Formwork

IS 456:2000, IS 6461 : Part 5 : 1972

101. ACI 301 and ACI 347 Design of Formwork

102. ACI 117 - Standard Specifications for Tolerances for Concrete Construction

and Materials

Concrete Reinforcement IS 456:2000


Concrete for Buildings Concrete Reinforcement IS 456:2000

104. ACI 315 - Details and Detailing of

Concrete Reinforcement Concrete Reinforcement SP-34


for Structural Concrete Concrete Reinforcement IS 456:2000

106. ASTM A185 - Standard Specification

for Steel Welded Wire Fabric, Plain, for Concrete Reinforcement

Concrete Reinforcement IS 1566:1982






Sr. No.




107. ASTM A615 - Standard Specification for Deformed and Plain Billet-Steel Bars for Concrete Reinforcements

Concrete Reinforcement IS 1786: 1985

108.

ASTM A706 - Standard Specification

for Low-Alloy Steel Deformed Bars for Concrete Reinforcements

Concrete Reinforcement Relevant IS code

109.

AWS D12.1 - Recommended Practices for Welding Reinforcement Steel Metal Inserts, and Connections in Reinforced

Concrete Construction.

Concrete Reinforcement

IS 2751:1979

110. AWS D1.4 - Structural Weld Code -

Reinforcing Steel Concrete Reinforcement

111. CRSI - Manual of Practice, and

Documents 63 and 65 Concrete Reinforcement IS 12461:1988 & IS 11370:1985

112.

U.S.Army Corps of Engineers

Specification CRD C621 - Specification for Non-Shrink Grout

Non Shrink Grout Relevant Indian standard code


Compressive Strength of Hydraulic

Cement Mortars

Non Shrink Grout IS 4031 : 1988

114. AISC - Code of Standard Practice for

Steel Buildings and Bridges Structural Steel Requirements IS 800 / IS 1915

115.

AISC - Load and Resistance Factor

Design (LRFD) Specification for Structural Steel Buildings

Structural Steel Requirements IS 800

116. AISC - Specifications of Structural

Joints using ASTM A325 or A490 Bolts

approved by the Research Council in

Structural Steel Requirements IS 800 / IS 4000






Sr. No.




Structural Connections

117. AWS D1.1 - Structural Welding Code Structural Steel Requirements IS 816 / IS 1323

118. AWS A5.1 - Specification for Carbon Steel Electrodes for Shield Metal Arc

Welding Structural Steel Requirements

As per reputed approved manufacturer's standard or relevant IS Standard

119. AWS A5.5 - Specifications for Low-Alloy Steel Covered Arc Welding Electrodes

Structural Steel Requirements

As per reputed approved manufacturer's standard or relevant IS Standard

120. AWS A5.17 - Specification of Carbon

Steel Electrodes and Fluxes for Submerged Arc Welding


121. AWS A5.20 - Specification for Carbon Steel Electrodes for Flux Cored Arc

Welding


122. SSPC - Steel Structures Painting

Manual Structural Steel Requirements

As per Thermax's Standard Painting Specifications

for Export Projects

123. ASTM A36 - Standard Specification for

Structural Steel Structural Steel Requirements IS 2062

124.


for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products)



for Zinc Coating (Hot-Dip) on Iron and Steel Hardware


126. ASTM A780 - Standard Practice for Repair of Damaged and Uncoated







Sr. No.




Areas of Hot-Dip Galvanized Coatings


for Carbon Steel Bolts and Studs, 60,000 PSI Tensile Strength

Structural Steel Requirements HT BOLTS - B7/2HIS 1367

128.

ASTM A325 - Standard Specification for Structural Bolts, Heat Treated,

120/105 KSI Minimum Tensile Strength



for Heat-Treated Steel Structural Bolts,

150 KSI Minimum Tensile Strength


130.

ASTM A500 - Standard Specification for Cold-Formed Welded and Seamless Carbon Steel Tubings in Rounds and

Shapes

Structural Steel Requirements IS 1239 / 3589

131.


for Hot-Formed Welded and Seamless Carbon Steel Structural Tubing

Structural Steel Requirements Relevant IS Code

132. ASTM A992 - Standard Specification for Steel and Structural Shapes For

Use in Building Framing

Structural Steel Requirements SP6 / IS 2062

133. ASTM F436 - Standard Specification

for Hardened Steel Washers Structural Steel Requirements Relevant IS Code

134. ASTM F844 - Standard Specification

for Washers, Steel, Plain (Flat), Unhardened for General Use

Structural Steel Requirements B 16.20






Sr. No.




135.

American Institute of Steel Construction (AISC) Quality

Certification Program for Conventional Steel Buildings (Sbd)

Fabricator's qualifications Relevant IS Code

136. AWS Certified Welding Inspectors Fabricator's qualifications IBR

137. ASTM B633 Adhesive Anchors Relevant IS Code

138. ASTM B695 Galvanizing IS4736

139. NEC Articles 501 and 502 IS 1913, IS 8224.

140. IEC Codes Electrical Construction

IS 12943, IS 2148, IS8309, IS3043, IS9537, IS3837, IS2667, IS3419, IS3480, IS6946, IS4649, IS1293,

IS3070. 141.

AFBMA Anti-Friction Bearing Manufacturers Association

Electrical Construction

142. ANSI American National Standards

Institute Electrical Construction

143. ASME American Society of Mechanical

Engineers Electrical Construction


IS3070.

144. ASTM American Society for Testing and

Materials Electrical Construction

145. FM Factory Mutual Electrical Construction






Sr. No.




146. ICEA Insulated Cable Engineers

Association Electrical Construction

147. ICS Institute for Industrial Controls

and Enclosures Electrical Construction


IS3070.

148. ISA Instrument Society of America Electrical Construction

149. IEEE Institute of Electrical and

Electronic Engineers Electrical Construction

150. IES Illuminating Engineering Society of

North America Electrical Construction

151. MG 1 Standard Publications for Motors

and Generators Electrical Construction


IS3070. 152. NEC National Electrical Code Electrical Construction

153. NEMA National Electrical

Manufacturers Association Electrical Construction

154. OSHA Occupational Safety and Health

Administration Electrical Construction


IS3070.

155. National Electrical Safety Code (NESC) Electrical Construction OSHA

156. API RP 500 Section 14 and NFPA 497 Electrical area classification drawing Not applicable for Power plant area as it is safe area.






Sr. No.




157. NEC Article 392 For cable tray system IS 9537, IS3837, IS2667

158. IEC Codes and Standards or NEMA VE

2 and Aluminium Association's Specifications

Material of cable trays IS 9537, IS3837, IS2667

159. IEC Codes and Standards or NEMA FG

1 and UL 568 For fiberglass cable trays Not applicable.

160. ICEA Codes and Standards For all wires and cables IS: 7098, IS: 1554, IS10810.

161. ICEA S-66-524 and UL 1569 For 600 V multiple conductor power

wiring Indian Electricity Act, Electricity supply Act, Indian

Electricity Rules.

162. NEC Article 310 For 600 V single conductor power

and control wiring IS 694

163. NEMA WC 70 For multi conductor cable IS: 7098, IS: 1554, IS10810.

164. ANSI MC 96.1 For single pair thermocouple

extension cable ANSI MC 96.1

165. ASA/ISA Color coding of conductors IS: 7098, IS: 1554, IS10810.

166. NEC Article 100 For medium voltage power cables IS: 7098, IS: 1554, IS10810.

167. NEC Article 344, 501 or 502 Conduit systems for medium voltage

power cables IS 9537,IS3837,IS2667






Sr. No.




168. ICEA S-68-516 and UL 1072 Material for multiconductor 15 kV

power cable IS 7098

169. AEIC CS6 For Insulated conductors IS: 8130

170. ASTM B-496 and UL 1072 For grounding conductor IS 3043

171. IEEE 576 For installing, terminating and

testing cables IS: 10810

172. NFPA Codes and Standards For emergency and egress lighting IS 9583

173. NEMA 12 and NEMA 4X For pull boxes and junction boxes IS 3837, IS 2667.

174.

ANSI/NEMA Std. Pub. No. FB 1, "Fittings and Supports for Conduit and

Cable Assemblies" and National Electrical Contractor's Association's

"Standard of Installation" and UL

Compliance

For anchors, fasteners, hangers, supports and equipment mounting

IS 3837, IS 2667.

175. NEC/IEC For substation grounding IEEE 80-2000

176. IEEE 80-2000 Grounding of outdoor 66 kV open

bus substation section IEEE 80-2000

177. NFPA 780 and UL 96 Common ground bonding with Lightning Protection System

IS 2309.






Sr. No.




178. ANSI C57, IEC, IEEE and NEMA Codes

and Standards For Power Transformers IS:2026 (Part I-IV)

179. ANSI C57 For Total losses and overload capacity and noise levels of

Transformers IEC: 85

180. NEMA MG-1 For motors in MCC IS: 325

181. IEC1131-3 For Graphical User Interface IEC1131-3

182. ISA-S5.4 - 1989 For loop wiring diagrams ISA-S5.4 - 1989

183. NFPA 85 Standard for Boiler and

Combustion Systems Hazards Code For safety trips and burner

management NFPA 85 Standard for Boiler and Combustion

Systems Hazards Code

184. IEC 100 (Electromagnetic Compatibility

Standard)* Instrumentation Specifications

Vendor Specific, Shall be confirmed during detail engineering stage

185. IEC1131-3 (Confirmation Software

Standard) Instrumentation Specifications IEC1131-3 (Confirmation Software Standard)

186. ISA S88 (Batch Software Standard) Instrumentation Specifications ISA S88 (Batch Software Standard)

187. ISA Instrumentation Specifications ISA

188. IEC60068-2-1* IEC60068-2-2*

IEC 60068-2-14*

Temperature Test, Quality Requirements

Vendor Specific, Shall be confirmed during detail engineering stage






Sr. No.




189. IEC 60068-2-30* Humidity Test, Quality Requirements Vendor Specific, Shall be confirmed during detail

engineering stage 190. IEC 60068-2-6* Vibration Test, Quality Requirements

191. IEC 60068-2-27* Shock Test, Quality Requirements

Vendor Specific, Shall be confirmed during detail

engineering stage

192. CISPR 11: Group 1, Class A* Emissions Test, Quality

Requirements

193. IEC 60068-4-2* ESD Immunity Test, Quality

Requirements

194. IEC 60068-4-3* Radiated RF Immunity Test, Quality

Requirements

195. IEC 60068-4-4* EFT/B Immunity Test, Quality

Requirements

196. IEC 60068-4-5* Surge Transient Immunity Test,

Quality Requirements Vendor Specific, Shall be confirmed during detail

engineering stage 197. IEC 60068-4-6*

Conducted RF Immunity Test,

Quality Requirements

198. Not Mentioned Instrument and apparatus for

temperature measurement ASME PTC 19.3 (1974)

199. Not Mentioned Temperature Measurement -

Thermocouples ANSI - MC 96.1 - 1982

200. Not Mentioned Temperature Measurement by

electrical resistance thermometers IS: 2806






Sr. No.




201. Not Mentioned Thermometer-element-Platinum

resistance IS: 2848 / DIN 43760

202. Not Mentioned Instrument and apparatus for

pressure measurement ASME PTC 19.2 (1964)

203. Not Mentioned Bourdon tube pressure and vacuum

gauges IS: 3624/1996

204. Not Mentioned Instruments and apparatus for flow

measurement ASME PTC 19.5 (1972) Interim supplement, Part-II

205. Not Mentioned Measurements of fluid flow in closed

conduit ISO-5167

206. Not Mentioned

Safety requirements for electrical

and electronic measuring and controlling instrumentation

ANSI C 39.5 / 1974

207. Not Mentioned Compatibility of analog signals for

electronic industrial process

instruments

ISA-S 50.1: ANSI MC 12.1 / 1975

208. Not Mentioned Dynamic response testing of process

control instrumentation ANSI MC 4.1 (1975) - ISA -S26 (1968)

209. Not Mentioned Surge withstand capability (SWC)

tests ANSI C 37.90A (1989), IEC-255.4

210. Not Mentioned Printed circuit boards IPC TM-650, IEC 326C

211. Not Mentioned General requirements and tests for

printed wiring boards IS-7405 (Part-I)/1973






Sr. No.




212. Not Mentioned Edge socket connectors IEC 130-11

213. Not Mentioned Requirements and methods of testing

of wire wrap terminations DIN 41611 Part-2

214. Not Mentioned Dimensions of attachment plugs and

receptacles ANSI C73-1973.(Supplement ANSI C73a 1980)

215. Not Mentioned Contact Rating - AC services NEMA ICS Part-2 125, A-600

216. Not Mentioned Contact Rating - DC services NEMA ICS Part-2 125, N-600

217. Not Mentioned Types of enclosures IS 13947 (Part I) 1993

218. Not Mentioned Racks, panels and associated

equipment EIA: RS-310-C-1983 (ANSI C83.9 - 1972)

219. Not Mentioned Classification of degree of protection

provided by enclosure IEC 529

220. Not Mentioned Classification of hazardous area NEMA Article 500, Volume-6, 1978

221. Not Mentioned Electrical Instruments in hazardous

dust locations ISA-RP 12.11

222. Not Mentioned Intrinsically safe apparatus NFPA Article 493 Volume-4 1978

223. Not Mentioned Purged and pressurized enclosure for

electrical equipment in hazardous NFPA Article 496 Volume-4, 1978






Sr. No.




location

224. Not Mentioned Stainless Steel material of tubing and valves, for sampling system

ASTM A 269-79 GRTO-316

225. Not Mentioned Submerged helical coil heat

exchangers for sample coolers ASTM D11-98

226. Not Mentioned Specifications and guides for the use

of general-purpose annunciators ISA RP 18.1

227. Not Mentioned Surge withstand capability tests for

Anunciators ANSI C37.90 a -1971 and IEEE Standard 472-1974

228. Not Mentioned Relays and relay system associated

with electric power apparatus IEEE Standards 3.13


Interlocks & Protections ANSI C37.90 a - 1971 and IEEE Standard 472-

1974

230. Not Mentioned

General requirements and tests for switching devices for control and

auxiliary circuits including contactor

relays

IS-6875 (Part-I)/1973

231. Not Mentioned Turbine water damage prevention ASME-TDP-1-1980

232. Not Mentioned Boiler safety interlocks NFPA Section 85B, 85D, 85E, 85F, 85G

233. Not Mentioned Practice and requirements for semi-

conductor power rectifiers ANSI C34.2






Sr. No.





UPS ANSI C 70.90 A/1971, IEC-255.4

235. Not Mentioned Recommended practice for sizing

large VRLA batteries for generating stations and sub-stations

IEEE-485

236. Not Mentioned Flow equation for Sizing Control

Valve ISA-S39.2 / 1972

237. Not Mentioned Control Valve seat leakage ANSI / FCI 70.2

238. Not Mentioned Face to face dimensions of Control

Valves ANSI B16.10, ISA S75.03 & ISA S75.16

239. Not Mentioned Steel pipe, Flanges and flanged

fittings ANSI B16.5

240. Not Mentioned Steel valves, flanges and Butt weld

ends ANSI B16.34

241. Not Mentioned Control Valve Capacity Test

Procedure ISA S75.02

242. Not Mentioned Seamless Carbon Steel Pipe for

Instrument Tubing ASTM-A-106

243. Not Mentioned Material for socket weld fittings ASTM-A-105

244. Not Mentioned Dimensions of fittings ANSI-B16.11






Sr. No.




245. Not Mentioned Code for pressure piping, welding,

hydrostatic testing ANSI-B 31.1

246. Not Mentioned Nomenclature for instrument tube

fittings ISA-RP 42.1 / 1982

247. Not Mentioned Seamless Stainless Steel Tubes for

Instrument Tubing ASTM A-312 TP 304

248. Not Mentioned Alloy Steel Pipe for Instrument

Tubing ASTM A 335 Gr P22

249. Not Mentioned Thermocouple extension wires /

cables ANSI MC96.1

250. Not Mentioned Color-coding of single or multi-pair

cables IPCEA S-61-402

251. Not Mentioned Guide for design and installation of cable system in power generating

station (insulation, jacket materials)

IEEE Standard 422

252. Not Mentioned Requirements of vertical tray flame

test IEEE 383

253. Not Mentioned Standard specification for tinned soft or annealed copper wire for electrical

purpose ASTM B33

254. Not Mentioned

Guide for the design and installation of cable system in power generating

station (cable trays, support systems, conduits)

IEEE Standard 422, NEMA VE-1, NEC-1981. Test Standards NEMA VE-1-1979

255. Not Mentioned Galvanizing of carbon steel cable

trays ASTM A-386






Sr. No.




256. Not Mentioned Mono-mode fiber ITU-T G.652

*Note: Adherence/Compliance of these codes is vendor specific, shall be confirmed during detailed engineering stage.