analog automotive guide - texas instruments

AnalogAutomotiveGuide

2008

Amplifiers

Audio

Comparators

Data Converters

Interface

Power Management

Analog Automotive Guide Texas Instruments 2008

2 Analog Automotive Guide

Table of ContentsOperational Amplifiers/Comparators

Current-Shunt Monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Precision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Low Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Wide Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5High Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6General Purpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6Comparators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Power Management

Low-Dropout Regulators (LDOs) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8DC/DC Controllers and Converters . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10LED Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12PWM Power Supply Controllers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13USB Power Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13Supervisors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Power and Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Interface

CAN/LIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16LVDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17RS-485/422/232 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Data Converters/Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Design Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

TI Worldwide Technical SupportInternetTI Semiconductor Product Information Center Home Pagesupport.ti.comTI Semiconductor KnowledgeBase Home Pagesupport.ti.com/sc/knowledgebase

Product Information CentersAmericasPhone +1(972) 644-5580 Fax +1(972) 927-6377Internet/Email support.ti.com/sc/pic/americas.htm

Europe, Middle East, and AfricaPhone

European Free Call 00800-ASK-TEXAS(00800 275 83927)

International +49 (0) 8161 80 2121

Russian Support +7 (4) 95 98 10 701

Note: The European Free Call (Toll Free) number is not active in all countries. If you havetechnical difficulty calling the free call number, please use the international number above.

Fax +(49) (0) 8161 80 2045Internet support.ti.com/sc/pic/euro.htm

JapanFax

International +81-3-3344-5317 Domestic 0120-81-0036Internet/Email

International support.ti.com/sc/pic/japan.htmDomestic www.tij.co.jp/pic

AsiaPhone

International +91-80-41381665Domestic Toll-Free Number Toll-Free Number

Australia 1-800-999-084 Malaysia 1-800-80-3973China 800-820-8682 New Zealand 0800-446-934Hong Kong 800-96-5941 Philippines 1-800-765-7404India 1-800-425-7888 Singapore 800-886-1028Indonesia 001-803-8861-1006 Taiwan 0800-006800Korea 080-551-2804 Thailand 001-800-886-0010

Fax +886-2-2378-6808 Email [email protected] support.ti.com/sc/pic/asia.htm [email protected]

C010208Important Notice: The products and services of Texas Instruments Incorporated and its subsidiariesdescribed herein are sold subject to TI’s standard terms and conditions of sale. Customers are advised toobtain the most current and complete information about TI products and services before placing orders. TIassumes no liability for applications assistance, customer’s applications or product designs, softwareperformance, or infringement of patents. The publication of information regarding any other company’sproducts or services does not constitute TI’s approval, warranty or endorsement thereof.

Safe Harbor Statement: This publication may contain forward-looking statements that involve a number ofrisks and uncertainties. These “forward-looking statements” are intended to qualify for the safe harbor fromliability established by the Private Securities Litigation Reform Act of 1995. These forward-looking statementsgenerally can be identified by phrases such as TI or its management “believes,” “expects,” “anticipates,”“foresees,” “forecasts,” “estimates” or other words or phrases of similar import. Similarly, such statementsherein that describe the company's products, business strategy, outlook, objectives, plans, intentions or goalsalso are forward-looking statements. All such forward-looking statements are subject to certain risks anduncertainties that could cause actual results to differ materially from those in forward-looking statements.Please refer to TI's most recent Form 10-K for more information on the risks and uncertainties that couldmaterially affect future results of operations. We disclaim any intention or obligation to update any forward-looking statements as a result of developments occurring after the date of this publication.

Trademarks in this issue: The platform bar, FlatLink, PowerPAD and SWIFT are trademarks of TexasInstruments. All other trademarks are the property of their respective owners.

© 2008 Texas Instruments Incorporated

Printed in U.S.A. by (Printer, City, State), on recycled paper

Texas Instruments Commitment to Automotive

Texas Instruments (TI) is committed to providing superior cost-effective solutions to the automotive market along with benchmarkservice in terms of excellent product documentation, on-timedelivery and conformance to specifications.

Availability/CommitmentTI supports the requirements defined by the automotive industry,and continues to add to our automotive portfolio. With more than30 years of experience serving customers with demanding require-ments, TI enables customers to achieve the quality, reliability andcost goals needed to succeed in today’s marketplace.

TI Automotive Capabilities• TS16949 certified• Automotive temperature range• Automotive qualification• Six month product change notification

Texas Instruments 2008 Analog Automotive Guide

Operational Amplifiers/Comparators

Current-Shunt Monitors

3

Current-Shunt Monitors Selection GuideCommon Input Input Small Quiescent

Mode Input Offset (±) Offset CMRR Signal Current (±) VS VS AutoGain Range (min) (max) Drift (±) (typ) (min) Bandwidth (typ) (min) (max) Qual

Device Description (V/V) (V) (mV) (µV/°C) (dB) (typ) (MHz) (mA) (V) (V) (Q1)INA193A/4A/5A Wide common mode 20, 50, 100 –16 to 80 2 2.5 100 0.5, 0.3, 0.2 0.37 2.7 18 YINA196A/7A/8A Wide common mode 20, 50, 100 –16 to 80 2 2.5 100 0.5, 0.3, 0.2 0.37 2.7 18 YINA200/1/2 Integrated comparator and reference 20, 50, 100 –16 to 80 2.5 5 100 0.5, 0.3, 0.2 1.35 2.7 18 PreviewINA203/4/5 Dual integrated comparators and ref 20, 50, 100 –16 to 80 2.5 5 100 0.5, 0.3, 0.2 1.35 2.7 18 PreviewINA206/7/8 Dual integrated comparators and ref 20, 50, 100 –16 to 80 2.5 5 100 0.5, 0.3, 0.2 1.8 2.7 18 PreviewINA209 Bi-directional, current/power with Programmable 0 to 26 0.1 0.1 100 — 1 3.0 5.5 Preview

I2C interfaceINA270/1 Wide common mode, filter option 14, 20 –16 to 80 2.5 2.5 100 0.13 0.7 2.7 18 YINA138 Current output 1 to 100 2.7 to 36 2 1 100 0.8 0.025 2.7 36 YINA139 Current output 1 to 100 2.7 to 36 2 1 100 0.44 0.06 2.7 40 YINA168 Current output, wide supply range 1 to 100 2.7 to 60 2 1 100 0.8 0.025 2.7 60 YINA169 Current output, wide supply range 1 to 100 2.7 to 60 2 1 100 0.44 0.06 2.7 60 Y

TI’s INA270 (G = 14 V/V) and INA271 (G = 20 V/V) are two-stage, high-side current-shunt monitors. They provide a wide common-mode voltage range (–16 to +80 V) that makes themwell-suited for automotive applications where protection against high-voltage transients andbattery reversal is required. Operating from supplies ranging from 2.7 to 18 V, they offer ±3%maximum output error over the extended temperature range of –40 to +125°C.

With a common-mode rejection ratio (CMRR) of 120 dB, the dynamics of common-mode voltagesare no longer an issue. The two-stage topology of the INA270/1 readily enables filtering andpreserves the buffered voltage output, eliminating the need for an additional op amp. Typicalapplications include control of (BL)DC-motors and variable-force solenoids.

GND

IN+ IN–

RL

PREOUT

BUFIN

RS

A2

A1

–16-V to +80-VSupply

V+ 2.7to 18 V

INA270

Output

Load

V+

96 kΩ

5 kΩ 5 kΩ

Key Features• Wide common-mode voltage range

(–16 to +80 V)• Supplies of 2.7 to 18 V• 120-dB CMRR• Offset voltage: 0.5 mV• Total output error: ±3% maximum• Two-stage topology enables filtering with

buffered output

Benefits• Allows for filtering with buffered output• Eliminates the need for an additional

op amp• Filtering can be done with a single cap

Two-Stage, Voltage-Output Current-Shunt Monitor

INA270, INA271

Get samples and datasheets at: www.ti.com/sc/device/INA270A-Q1 or www.ti.com/sc/device/INA271A-Q1



Precision/Low-Voltage Operational Amplifiers

4

Precision Operational Amplifiers (VIO ≤ 1 mV) Selection GuideIq per Slew VIO Offset IB VN at

VS VS Ch. GBW Rate (25°C) Drift (25°) CMRR 1 kHz Rail- Auto(min) (max) (max) (typ) (typ) (max) (typ) (max) (min) (typ) Single to- Qual

Device1 Description Ch. (V) (V) (mA) (MHz) (V/µs) (mV) (µV/°C) (pA) (dB) (nV/√Hz—

) Supply Rail (Q1)OPAy333 Zero drift 1, 2 1.8 5.5 0.017 0.35 0.16 0.01 0.02 200 106 1.1 Y I/O PreviewTLE2037A High speed, reduced VIO 1 8.0 38 5.3 50 7.5 0.025 0.2 90000 117 2.5 N N YTLE2037 High speed 1 8.0 38 5.3 50 7.5 0.1 0.4 90000 100 2.5 N N YOPAy365 Zero-crossover, RRIO 1, 2 2.2 5.5 5 50 25 0.2 1 10 100 5 Y I/O PreviewTLE202xA Wide voltage range, reduced VIO 1, 2, 4 4.0 40 0.3 1.2 0.5 0.4 2 70000 82, 85, 87 17 Y — YTLE202x Wide voltage range 1, 2, 4 4.0 40 0.3 1.2 0.5 0.6 2 70000 85, 80 17 Y — YTLC225xA µPower, rail-rail out, reduced VIO 2, 4 4.4 16 0.0625 0.2 0.12 0.85 0.5 60 70 19 Y Out YTLV225xA Low voltage, rail-rail out, reduced VIO 2, 4 2.7 16 0.0625 0.2 0.1 0.85 0.5 60 65 19 Y Out YTLC226xA Rail-rail out, reduced VIO 2, 4 4.4 16 0.25 0.71 0.55 0.95 2 800 70 12 Y Out YTLC227xA Low noise, reduced VIO 2, 4 4.4 16 1.5 2.2 3.6 0.95 2 60 70 9 Y Out YTLV2422A Low voltage, reduced VIO 2 2.7 10 0.075 0.052 0.02 0.95 2 60 70 23 Y Out YTLV243xA RRIO, reduced VIO 2, 4 2.7 10 0.125 0.5 0.25 0.95 2 60 70 18 Y I/O YTLV244xA Reduced VIO 2, 4 2.7 10 1.1 1.75 1.3 0.95 2 260 65 18 Y Out Y

1x indicates: 0 = single with shutdown, 1 = single, 2 = dual, 3 = dual with shutdown, 4 = quad, 5 = quad with shutdown. y indicates: no character = single, 2 = dual, 3 = triple, 4 = quad.

Low-Voltage Operational Amplifiers (VS ≤ 2.7 V) Selection GuideIq per Slew VIO Offset VN at

VS VS Ch. GBW Rate (25°C) Drift IB 1 kHz Rail- Auto(min) (max) (max) (typ) (typ) (max) (typ) (max) (typ) to- Qual

Device1 Description Ch. SHDN (V) (V) (mA) (MHz) (V/µs) (mV) (µV/°C) (pA) (nV/√Hz—

) Rail (Q1)OPAy333 Zero drift 1, 2 N 1.8 5.5 0.017 0.35 0.16 0.01 0.02 200 1.1 I/O PreviewLMV93x 1.8V with RRIO 1, 2, 4 N 1.8 5.5 0.185 1.4 0.35 4 5.5 65000 60 I/O YOPAy348 1MHz, 45µA, RRIO 1, 2, 4 N 2.1 5.5 0.065 1 0.5 5 2 10 35 I/O PreviewTLV277x High slew rate 1, 2, 4 Y 2.5 6.0 2 5.1 2.7 2.5 2 60 21 Out YTLV240x Wide voltage range, sub-µPower, RRIO 1, 2, 4 N 2.5 16 0.00095 0.0055 0.0025 1.2 3 300 — I/O YLMV34x Rail-to-rail output 1, 2, 4 Y 2.5 5.5 0.17 1 1 4 1.7 120 40 Out YLMV82x Wide bandwidth 1, 2, 4 N 2.5 5.5 0.3 5 2.5 6 1 90000 45 Out YTLV2422 Low power, rail-rail output 2 N 2.7 10 0.075 0.052 0.02 2 2 60 23 Out YTLV237x Wide voltage range, 3MHz 1, 2, 4 Y 2.7 16 0.66 3 2.4 4.5 2 60 39 I/O YTLV244x Rail-to-rail output 2, 4 N 2.7 10 1.1 1.75 1.3 2 2 260 18 Out YTLV246x Low noise, wide bandwidth, 25mA drive 1, 2, 4 Y 2.7 6.0 0.575 6.4 1.6 2 2 14000 11 I/O YTLV246xA Low noise, wide bandwidth, 25mA drive 1, 2, 4 Y 2.7 6.0 0.575 6.4 1.6 1.5 2 14000 11 I/O YTLV247x Low bias current, 35mA drive 1, 2, 4 Y 2.7 6.0 0.75 6.4 1.4 2.2 0.4 50 15 I/O YTLV225x Wide voltage range 2, 4 N 2.7 16 0.0625 0.187 0.1 1.5 0.5 60 19 Out YLMV324/LMV358 Low power 2, 4 N 2.7 5.5 0.25 1 1 7 5 250000 39 Out YTLV27x Wide voltage range, 3MHz 1, 2, 4 N 2.7 16 0.66 3 2.4 5 2 60 39 Out YTLV2211 µPower, rail-rail out 1 N 2.7 10 0.025 0.065 0.025 3 0.5 150 22 Out PreviewTL97x Very low noise 1, 2, 4 N 2.7 12 3.2 12 5 6 5 750000 4 Out Preview




Low-Power/Wide-Voltage-Range Operational Amplifiers

5

Low-Power Operational Amplifiers (Iq ≤ 1 mA) Selection GuideIq per Slew VIO Offset VN at

VS VS Ch. GBW Rate (25°C) Drift IB 1 kHz Rail- Auto(min) (max) (max) (typ) (typ) (max) (typ) (max) (typ) to- Qual

Device1 Description Ch. SHDN (V) (V) (mA) (MHz) (V/µs) (mV) (µV/°C) (pA) (nV/√Hz—

) Rail (Q1)TLV240x Wide voltage range, sub-µPower, RRIO 1, 2, 4 N 2.5 16 0.00095 0.0055 0.0025 1.2 3 300 — I/O YOPAy333 Zero drift 1, 2 N 1.8 5.5 0.017 0.35 0.16 0.01 0.02 200 1.1 I/O PreviewTLV2211 µPower, rail-rail out 1 N 2.7 10 0.025 0.065 0.025 3 0.5 150 22 Out PreviewTLV225x Wide voltage range 2, 4 N 2.7 16 0.0625 0.187 0.1 1.5 0.5 60 19 Out YTLC225x µPower, rail-rail out 2, 4 N 4.4 16 0.0625 0.2 0.12 1.5 0.5 60 19 Out YOPAy348 1MHz, 45µA, RRIO 1, 2, 4 N 2.1 5.5 0.065 1 0.5 5 2 10 35 I/O PreviewTLV243x RRIO 2, 4 N 2.7 10 0.125 0.5 0.25 2 2 300 18 I/O YTLV2422 Low power, rail-rail output 2 N 2.7 10 0.075 0.052 0.02 2 2 60 23 Out YLMV93x 1.8V with RRIO 1, 2, 4 N 1.8 5.5 0.185 1.4 0.35 4 5.5 65000 60 I/O YLMV34x Rail-rail output 1, 2, 4 N 2.5 5.5 0.2 1 1 4 1.7 120 40 Out YLMV358 Low power 2 N 2.7 5.5 0.2 1 1 7 5 250000 46 Out YTLC226x Rail-rail output 2, 4 N 4.4 16 0.25 0.82 0.55 2.5 2 100 12 Out YLMV32x Low power 1, 2, 4 N 2.7 5.5 0.25 1 1 7 5 250000 39 Out YTLE202x Wide voltage range 1, 2, 4 N 4.0 40 0.3 1.2 0.5 0.6 2 70000 17 N YLMV82x Wide bandwidth 1, 2, 4 N 2.5 5.5 0.3 5 2.5 6 1 90000 45 Out YTLV246x Low noise, wide bandwidth, 25mA drive 1, 2, 4 Y 2.7 6.0 0.575 6.4 1.6 2 2 14000 11 I/O YTLV237x Wide voltage range, 3MHz 1, 2, 4 Y 2.7 16 0.66 3 2.4 4.5 2 60 39 I/O YTLV27x Wide voltage range, 3MHz 1, 2, 4 N 2.7 16 0.66 3 2.4 5 2 60 39 Out YTLV247x Low bias current, 35mA drive 1, 2, 4 Y 2.7 6.0 0.75 2.8 1.4 2.2 0.4 50 15 I/O Y


Wide-Voltage-Range Operational Amplifiers (VS ≥ 15 V) Selection GuideIq per Slew VIO Offset VN at

VS VS Ch. GBW Rate (25°C) Drift IB CMRR 1 kHz Rail- Auto(min) (max) (max) (typ) (typ) (max) (typ) (max) (min) (typ) Single to- Qual


) Supply Rail (Q1)TLE214x High speed, single supply 1, 2, 4 4.0 44 4.5 5.9 45 0.9, 1.2, 2.4 1.7 1500000 85 10.5 Y N PreviewTLE202x Precision, single supply, low power 1, 2, 4 4.0 40 0.3 1.2 0.5 0.6 2 70000 85 17 Y N YTLE207x Low noise, high speed, JFET-input 1, 2 4.5 38 1.8 10 45 6 2.4 175 80 14 N N YTLE2037 Low noise, high speed, precision 1 8.0 38 5.3 50 7.5 0.1 0.4 90000 100 2.5 N N YTL347x Enhanced general purpose 2, 4 4.0 36 4.5 4 13 12 10 500000 65 49 Y N YTL08x JFET input, general purpose 1, 2, 4 7.0 36 2.8 3 13 15 18 400 70 18 N N YTLV240x Sub-µPower, RRIO 1, 2, 4 2.5 16 0.00095 0.0055 0.0025 1.2 3 300 63 — Y I/O YTLV225x Low power, rail-rail out 2, 4 2.7 16 0.0625 0.2 0.1 1.5 0.5 60 65 19 Y Out YTLV27x 550µA/Ch, 3MHz, rail-rail out 1, 2, 4 2.7 16 0.66 3 1.4 5 2 60 58 39 Y Out YTLV237x 550µA, 3MHz 1, 2, 4 2.7 16 0.66 3 2.4 4.5 2 60 57 39 Y I/O YTLC225x Low power, rail-rail out 2, 4 4.4 16 0.0625 0.2 0.1 1.5 0.5 60 70 19 Y Out YTLC227x Low noise, rail-to-rail out 2, 4 4.4 16 1.5 2.2 3.6 2.5 2 60 70 9 Y Out YTLC226x Low power, rail-rail out 2, 4 4.4 16 0.25 0.82 0.55 2.5 2 800 70 12 Y Out YTLC07x Low noise, high drive 1, 2, 4 4.5 16 2.5 10 16 1.9 1.2 50 100 7 Y N PreviewTLC08x Low noise, high drive, input range incl GND 1, 2, 4 4.5 16 2.5 10 16 1.9 1.2 50 70 8.5 Y N Y




High-Speed/General-Purpose Operational Amplifiers

6

High-Speed Operational Amplifiers (GBW ≥ 10 MHz) Selection GuideIq per Slew VIO Offset VN at

VS VS Ch. GBW Rate (25°C) Drift IB CMRR 1 kHz Rail- Auto(min) (max) (max) (typ) (typ) (max) (typ) (max) (min) (typ) Single to- Qual


) Supply Rail (Q1)THS4509 Wideband fully differential 1 3.0 5.5 38 3000 6600 1 2.6 13000 90 1.9 N N PreviewTHS4041 165MHz C-stable, high output drive 1 9.0 32 10 165 400 13 10 — 70 14 N N YTLE2037 Low-noise, precision, wide voltage range 1 8.0 38 5.3 50 7.5 0.1 0.4 90000 100 2.5 N N YLM218 Wide voltage range 1 10 40 8 15 70 10 — 250000 80 — N N YTL97x Low voltage, low noise 1, 2, 4 2.7 12 3.2 12 5 6 5 750000 60 4 Y Out PreviewTLE207x Low noise, JFET input 1, 2, 4 4.5 38 1.8 10 45 6 2.4 175 80 14 N N YTLC07x Low noise, high drive 1, 2, 4 4.5 16 2.5 10 16 1.9 1.2 50 95 7 Y N PreviewTLC08x Low noise, high drive, input range incl GND 1, 2, 4 4.5 16 2.5 10 16 1.9 1.2 50 70 8.5 Y N Y


General-Purpose Operational Amplifiers Selection GuideIq per Slew VIO Offset VN at

VS VS Ch. GBW Rate (25°C) Drift IB CMRR 1 kHz(V) (V) (mA) (MHz) (V/µs) (mV) (µV/°C) (pA) (dB) (nV/√Hz

—) Single

Device1 Description Ch. (min) (max) (max) (typ) (typ) (max) (typ) (max) (min) (typ) Supply Auto Qual (Q1)LM218 High-speed op amp 1 10 40 8 15 70 10 — 250000 80 — N YLM2902 General purpose 4 3.0 26 0.3 1.2 0.5 7 7 250000 50 35 Y YLM2902KV Voltage enhanced, 2kV ESD 4 3.0 32 0.3 1.2 0.5 7 7 250000 50 35 Y YLM2902KAV Voltage enhanced, 2kV ESD, reduced VIO 4 3.0 32 0.3 1.2 0.5 2 7 250000 50 35 Y YLM2904 General purpose 2 3.0 26 0.6 0.7 0.3 7 7 250000 50 40 Y YLM2904AV Voltage enhanced, reduced VIO 2 3.0 32 0.6 0.7 0.3 2 7 250000 65 40 Y YLM2904V Voltage enhanced 2 3.0 32 0.6 0.7 0.3 7 7 250000 65 40 Y YLMV32x Low voltage, rail-rail output 1, 2, 4 2.7 5.5 0.25 1 1 7 5 250000 50 39 Y YLMV34x Rail-rail output 1, 2, 4 2.5 5.5 0.2 1 1 4 1.7 120 56 40 Y YLMV358 Low voltage, rail-rail output 2 2.7 5.5 0.2 1 1 7 5 250000 46 39 Y YLMV82x Low voltage, low power, rail-rail out 1, 2, 4 2.5 5.5 0.3 5 2.5 6 1 90000 45 42 Y YLMV93x 1.8V with RRIO 1, 2, 4 1.8 5.5 0.185 1.4 0.35 4 5.5 65000 60 60 Y YTL08x Low noise, JFET input 1, 2, 4 7.0 36 2.8 3 13 15 18 400 70 18 N YTL347x Enhanced general purpose 2, 4 4.0 36 4.5 4 13 12 10 500000 65 49 Y YTLC227x Low noise, rail-rail out 2, 4 4.4 16 1.5 2.18 3.6 2.5 2 250000 80 9 Y YTLV27x 550µA/Ch 3MHz rail-rail output 1, 2, 4 2.7 16 0.66 3 1.4 5 2 60 58 39 Y Y




Comparators

7

Comparators Selection GuideIq per VIO tRESP Output

VS VS Ch. (25°C) Low-to- Current Auto(min) (max) (max) (max) High (min) Qual

Device1 Description Ch. (V) (V) (mA) (mV) (µs) (mA) Output Type (Q1)High Speed tRESP ≤ 0.2 µsLM211 High speed, strobed 1 3.5 30 6 3 0.115 — Open drain YLMV331 Low voltage 1 2.7 5.5 0.1 7 0.2 10 Open drain YLMV393 Low voltage 2 2.7 5.5 0.1 7 0.2 5 Open drain YLMV339 Low voltage 4 2.7 5.5 0.1 7 0.2 10 Open drain PreviewLow Power Iq < 0.5 mATLV370x Nanopower, push-pull, RRIO 1, 2, 4 2.5 16 0.0008 5 36 — Push pull YTLV3012A SOT-23 comparator and 1 1.8 5.5 0.005 12 6 — Push pull Preview

voltage referenceTLC370x Fast, low power 2, 4 4.0 16 0.02 5 1 4 Push pull YTLC393 General purpose, low power 2 4.0 16 0.02 5 1 6 Open drain YTLC339 General purpose, low power 4 3.0 16 0.02 5 1 6 Open drain PreviewLMV331 General purpose, low voltage 1 2.7 5.5 0.1 7 0.2 10 Open drain YLMV393 General purpose, low voltage 2 2.7 5.5 0.1 7 0.2 5 Open drain YLP2901 General purpose, low power 4 3.0 30 0.5 5 1.3 6 Open drain YWide Voltage Range VS ≥ 16 VLM2901V Voltage enhanced 4 2.0 32 0.625 7 0.3 6 Open drain YLM2901AV Voltage enhanced, reduced VIO 4 2.0 32 0.625 2 0.3 6 Open drain YLM2903V Voltage enhanced 2 2.0 32 0.5 7 0.3 6 Open drain YLM2903AV Voltage enhanced, reduced VIO 2 2.0 32 0.5 2 0.3 6 Open drain YLM2901 General purpose 4 2.0 30 0.625 7 0.3 6 Open drain YLP2901 General purpose, low power 4 3.0 30 0.5 5 1.3 6 Open drain YLM239A General purpose 4 2.0 30 0.5 2.5 0.3 6 Open drain YLM2903 General purpose 2 2.0 30 0.5 7 0.3 6 Open drain YTLC370x Fast, low power 2, 4 4.0 16 0.02 5 1.1 4 Push pull YTLC393 General purpose, low power 2 4.0 16 0.02 5 1.1 6 Open drain YTLC339 General purpose, low power 4 3.0 16 0.02 5 1 6 Open drain PreviewTLV370x Nanopower, push-pull, RRIO 1, 2, 4 2.5 16 0.0008 5 36 — Push pull Y



8 Power Management

Low-Dropout Regulators (LDOs)

Standard Linear Voltage Regulators Selection GuideVOUT/VREF Min IOUT

VOUT Tolerance IOUT for Iq VDO VDO VIN VIN – VOUT

(nom) Over Temp. (max) Regulation (max) (typ) (max) (max) (max) Auto QualDevice (V) (%) (mA) (mA) (mA) (V) (V) (V) (V) (Q1)LM317M Adj. (1.2 to 37) 0.7 500 3.5 — — 3 — 40 YUA78Mxx 3.3, 5, 10 5 500 — 6 2 2 to 2.5 25 to 30 — Y

Dual-Output LDOs Selection GuideFeatures

VDO1 VDO2 Iq @ VO VO VIN VIN

IO1 IO2 @ IO1 @ IO2 IO Voltage Accuracy (min) (max) Low (min) (max) Auto QualDevice Description (mA) (mA) (mV) (mV) (µA) (V) (%) (V) (V) /EN SVS Seq Noise (V) (V) (Q1)TPS767D3xx Dual-output, fast LDO with 1000 1000 350 — 125 3.3/2.5, 2 1.2 5 — — 2.7 10 Y

integrated SVS 3.3/1.8,3.3/Adj

TPS70175 Dual-output LDO with power-up 500 250 170 — 190 2.5/5.0 2 — — 2.7 6 Ysequencing for split-voltageDSP systems

The TLE4275-Q1 low-dropout regulator (LDO) is designed specifically for the harsh automotiveoperating environment. The device offers direct connection to the vehicle battery with the abilityto withstand load-dump transient conditions. Output stability has been optimized for typicalautomotive applications and low-cost capacitors.

IN OUT

DELAY

RESET

TLE4275-Q1

1 5

2

4

3

GND

ResetGenerator

BandgapReference

TemperatureSensor

SaturationControl andProtection

Circuit

Key Features• Output voltage: 5 V ±2%• Very low current consumption• Power-on and undervoltage reset• Resets low-level (<1-V) output voltages• Very low dropout voltage• Short-circuit protection• Reverse-polarity protection• ESD protection >6 kV

High-Input-Voltage LDO with Load-Dump Protection

TLE4275-Q1

Get samples and datasheets at: www.ti.com/sc/device/TLE4275-Q1


Power Management

Low-Dropout Regulators (LDOs)

9

LDOs Selection GuideVDO

at IO Iq at IO VIN VIN AutoIO (typ) Full Load Voltage (min) (max) Accuracy Qual

Device (mA) (mV) (µA) (V) Adj. (V) (V) (%) Packages Features1 Comments (Q1)TPS797xx 10 110 5 1.8, 3, 3.3 — 1.8 5.5 5, 4, 4 SC70 PG Low quiescent current YTPS715xx 50 415 3.2 2.5, 3, 3.3, 5 — 2.5 24 4 SC70 — Low quiescent current YTPS770xx 50 48 17 1.2, 1.5, 1,8, 2.5, 2.7 10 3 SOT23 /EN Low quiescent current Y

2.7, 2.8, 3, 3.3, 5TPS769xx 100 70 17 1.2, 1.5, 1.8, 2.5, 2.7 10 3 SOT23 /EN Low cost Y

2.7, 2.8, 3, 3.3, 5TPS791xx 100 38 170 1.8, 3.3, 4.7 2.7 5.5 2 SOT23 /EN RF low noise; high PSRR YTPS731xx 150 30 400 1.5, 1.8, 2.5 1.7 5.5 1 SOT23 /EN Reverse leakage protection Preview

3.0, 3.3, 5.0TPS763xx 150 300 85 1.6, 1.8, 2.5, 2.7, 2.7 10 3 SOT23 /EN Low cost Y

2.8, 3, 3.3, 3.8, 5TPS765xx 150 85 33 1.5, 1.8, 2.5, 2.7, 2.7 10 3 SO8 /EN Low quiescent current Preview

2.8, 3, 3.3, 5TPS771xx 150 265 125 1.5, 1.8, 2.7, 2.7 10 2 MSOP PG, /EN Fast transient response Y

2.8, 3.3, 5TPS793xx 200 100 170 1.8, 2.5, 2.8, 2.7 5.5 2 SOT23, MSOP, SOT223 EN RF low noise, high PSRR Y

2.85, 3, 3.3, 4.75TPS799xx 200 100 40 1.2 to 6 2.7 6.5 2 SOT23 /EN High PSRR PreviewTPS732xx 250 40 400 1.2, 1.5, 1.6, 1,8, 1.7 5.5 1 SOT23 /EN Reverse current protection Y

2.5, 3, 3.3, 5 Cap freeTPS773xx 250 150 90 1.5, 1.6, 1.8, 2.7, 2.7 10 2 MSOP /EN, SVS Low noise Preview

2.8, 3.3, 5.0TLE4275 450 500 150 5 — 5.5 45 2 DDPAK V, LD, RST Automotive LDO YTL760Mxx 500 500 — 1.8, 2.5, 3.3 — 3 45 2 DDPAK V, LD Automotive LDO, TLE4274 alternative YTPS71Hxx 500 150 285 3.3, 4.85, 5.0 4.3 10 2 PWP PG Fast transient response YTPS775xx 500 169 85 1.5, 1.6, 1.8, 2.7 10 2 SO8, PWP SVS Fast transient response Y

2.5, 3.3TPS776xx 500 169 85 1.5, 1.8, 2.5, 2.7 10 2 SO8, PWP PG Fast transient response Y

2.8, 3.3TL720Mxx 450 500 — 5 — 5.5 42 2 TO263, TO252 V Reverse polarity protection YTL750Mxx 750 600 — 5, 8, 12 — 6, 9, 13 60 3 DDPAK V, LD Automotive LDO, TLE4275 alternative YTL751Mxx 750 600 — 5, 8, 12 — 6, 9, 13 60 3 DDPAK V, LD, /EN Automotive LDO YTPS725xx 1000 170 75 1.5, 1.6, 1.8, 2.5 1.8 6 2 SO8 /EN, SVS Low noise, SVS PreviewTPS767xx 1000 230 85 1.5, 1.8, 2.5, 2.7, 2.7 10 2 SO8, PWP SVS Fast transient response Y

2.8, 3, 3.3, 5TPS768xx 1000 230 85 1.5, 1.8, 2.5, 2.7, 2.7 10 2 SO8, PWP PG Fast transient response Y

2.8, 3, 3.3, 5TPS753xx 1500 160 75 1.5, 1.8, 2.5, 3.3 2.7 5 2 PWP /EN, SVS Fast transient response YTPS786xx 1500 580 385 1.8, 2.5, 2.8, 2.7 5.5 3 DDPAK /EN Low noise Preview

3.0, 3.3TPS752xx 2000 210 75 1.5, 1.8, 2.5, 3.3 2.7 5 2 PWP /EN, SVS Fast transient response Y

1V = wide voltage, LD = load dump, PG = power good, /EN = active high enable, SVS = supply voltage supervisor, RST = reset.


Power Management

DC/DC Controllers and Converters

10

Switching DC/DC Converters Selection GuideVO VO VREF Driver

VIN (max) (min) Tol Current Auto QualDevice (V) (V) (V) (%) (A) (Q1) CommentsMC33063A 3 to 40 40 1.25 2 1.5 Y 1.5-A peak boost/buck/inverting switching regulatorTPIC74100 1.5 to 40 5 5 2 1 Y Buck/boost switch-mode regulatorTPS61040 1.8 to 6.0 28 VIN — 0.09 Y Boost mode, LED driverTPS61041 1.8 to 6.0 28 VIN — 0.05 Y Boost mode

Switching DC/DC Controllers Selection GuideVO VO VREF Driver Output Adaptive Auto

VIN (max) (min) Tol Current Current Multiple Voltage QualDevice (V) (V) (V) (%) (A) (A)1 Outputs Positioning Protection2 (Q1) CommentsTPS40050 8 to 40 30 0.7 1 1 20 No No OCP, UVLO Y Wide input range sync buck, source onlyTPS40051 8 to 40 30 0.7 1 1 20 No No OCP, UVLO Y Wide input range sync buck, source/sink except SSTPS40053 8 to 40 30 0.7 1 1 20 No No OCP, UVLO Y Wide input range sync buck, source/sinkTPS40057 8 to 40 35 0.7 1 1 20 No No SCP, UVLO Y Wide input range sync buck, source/sink with prebiasTPS5120 4.5 to 30 26 0.9 1.5 1.5 15 (each) Yes No OCP, UVLO, PG, OVP Y Dual 180 degree out-of-phase operationTL1451A 3.6 to 50 50 2.5 4 0.02 Depends on FET driver Yes No UVLO, SCP Y Dual PWM buck/boostTL5001A 3.6 to 40 50 1 3 0.02 Depends on FET driver No No UVLO, SCP Y PWM buck/boostTPS40200 4.5 to 52 46 0.7 2 0.2 Depends on FET driver No No — Y Wide input non-synchronous buck DC/DC controller

1Current levels of this magnitude and beyond can be supported.2OCP = over-current protection; UVLO = under-voltage lockout; SCP = short-circuit protection; PG = power good; OVP = over-voltage protection.

GND

RMOD

REST

AIN

VDRIVER

Cboot2

Cboot1

L1 L2

VOUT

PGND

RESET

SCR1

SCR0

TPIC74100-Q1

ENABLE

VLOGIC

AOUT

5 V

VBattery

5Vg_ENABLE

5Vg

CLP

4.7 nF4.7 nF

L

CR2

R1

470 nF

2.2 to

150 nF

OptionalConnection

5 kΩ

5 kΩ

1 to 100 µF

22 to 470 µF

12 kΩ

22 to 100 µH

5 V

5 V

TI’s TPIC74100-Q1 is an automotive, 5-V,fixed-output buck/boost converter with fixed440-kHz switching frequency. The device hasintegrated power switches for 1-A load cur-rent capability. Its wide input-voltage rangefrom 1.5 to 40 V allows operation even duringcold crank and load-dump conditions. Low-power operation and a standby mode makethe TPIC74100 suitable for applicationswhere power consumption is critical.

Key Features• 5-V output with ±2% accuracy• 1.5- to 40-V input operating range• 1-A load-current capability• 440-kHz switching frequency with spread

spectrum• Low-power operation and standby mode• Auxiliary switched 5-V output• Programmable slew rate and reset delay

Integrated, 5-V-Output Buck/Boost Converter with Extended Input-Voltage Range

TPIC74100-Q1

Get samples and datasheets at: www.ti.com/sc/device/TPIC74100-Q1


Power Management

DC/DC Controllers and Converters

11

SWIFT™ Step-Down Converters Selection GuideVIN Output Current VOUT Auto Qual

Device (V) (A) (V) Pin # / Pkg (Q1)TPS62000/1/2/3/4/5/6/7/8 2.0 to 5.5 0.6 Adj., 0.9, 1.0, 1.2, 1.5, 1.8, 1.9, 2.5, 3.3 10/MSOP YTPS5410 5.5 to 36 1 1.23 to 31 8/SO PreviewTPS62042 2.5 to 6.0 1.2 1.5 10/MSOP PreviewTPS54110 3.0 to 6.0 1.5 0.9 to 4.5 20/HTSSOP PreviewTPS5420 5.5 to 36 2 Adj 8/SO YTPS5430 5.5 to 36 3 Adj 8/HSO YTPS54310/1/2/3/4/5/6 3.0 to 6.0 3 Adj., 0.9, 1.2, 1.5, 1.8, 2.5, 3.3 20/HTSSOP YTPS54380 3.0 to 6.0 3 0.9 to 4.5 20/HTSSOP PreviewTPS5450 5.5 to 36 5 Adj 8/HSO PreviewTPS54372 3.0 to 6.0 6 0.2 to 4.5 20/HTSSOP YTPS54610/1/2/3/4/5/6 3.0 to 6.0 6 Adj., 0.9, 1.2, 1.5, 1.8, 2.5, 3.3 28/HTSSOP YTPS54680 3.0 to 6 6 0.9 to 4.5 28/HTSSOP Y

Inductorless DC/DC Regulators (Charge Pumps) Selection GuideVIN VOUT Adj. Efficiency Switching Frequency Quiescent Current Auto Qual

Device IOUT (mA) (V) (V) (%) (max) (kHz) (typ) (µA) (Q1)TPS60400 60 1.6 to 5.5 – (1.6 to 5.5) 99 375 125 YTPS60401 60 1.6 to 5.5 – (1.6 to 5.5) 99 30 65 YTPS60402 60 1.6 to 5.5 – (1.6 to 5.5) 99 75 120 YTPS60403 60 1.8 to 5.25 – (1.8 to 5.25) 90 325 425 Y

LCD/LED Display Bias Solutions Selection GuideVIN VIN No. of Minimum Switch Operating Auto

(min) (max) Regulated Current Limit Temp Range QualDevice (V) (V) Outputs (A) LDO DC/DC Converter Charge Pump Pin # / Pkg (°C) (Q1)TPS65140 2.7 5.8 4 1.6 1 1 2 24/HTSSOP –40 to 85 YTPS65145 2.7 5.8 4 0.96 1 1 2 24/HTSSOP –40 to 85 Y

VIN

NC

NC

ENA

GND

VSENSE

BOOT

PH

TPS5430

VIN VOUT

Key Features• Wide input voltage range: 5.5 V to 36 V• Up to 3-A continuous (4-A peak) output

current• High efficiency up to 95% enabled by

110-mΩ integrated MOSFET switch• Wide output voltage range: Adjustable

down to 1.22 V with 1.5% initial accuracy• Internal compensation minimizes external

parts count• Fixed 500-kHz switching frequency for

small filter size• Improved line regulation and transient

response by input-voltage feed forward• System overcurrent limiting, overvoltage

protection and thermal shutdown protection

3-A, Wide Input Range, Step-Down SWIFT™ Converter

TPS5430-Q1

Get samples, datasheets, evaluation modules and app reports at: www.ti.com/sc/device/TPS5430-Q1


Power Management

LED Drivers

12

LED Drivers Selection GuideVOUT Max Auto

VIN (max) LED No. of Current Serial QualDevice (V) Type (V) Configuration Channels (mA) Dimming1 Interface Diagnostics2 Protection2 Pin # / Pkg (Q1) CommentsTPS61040 1.8 to 6.0 Inductive 28 Series 1 400 Y N — SS, UVLO SOT-23 Y DC/DC boost converter for

white LEDsTPS61041 1.8 to 6.0 Inductive 28 Series 1 250 Y N — SS, UVLO SOT-23 Y DC/DC boost converter for

white LEDsTPIC6C595/6 4.5 to 5.5 Switch 33 Parallel 8 250 Y Y — OC 16/TSSOP, 16/SO N Power logic multichannel

switchTPIC2810 3.0 to 5.5 Switch 40 Parallel 8 210 Y Y — OT, IL 16/SO N Power logic multichannel

switchTLC5916 3.0 to 5.5 Linear 20 Parallel 8 120 Y Y OL, OT OT 16/TSSOP, 16/SO Y Linear multichannel

constant current sinkTLC5917 3.0 to 5.5 Linear 20 Parallel 8 120 Y Y OL, OT, SC OT 16/TSSOP, 16/SO Y Linear multichannel

constant current sinkTLC5940 3.0 to 5.5 Linear 18 Parallel 16 120 Y Y OL, OT OT 28/HTSSOP Preview Linear multichannel

constant current sink1May be via ENABLE pin, CONTROL pin, analog feedback network or programmable per serial interface.2SS = soft start; UVLO = under-voltage lockout; OC = over current; OT = over temperature; IL = current limit; OL = open load; RB = reverse battery; SC = shorted load.

The TLC5917 is designed for LED displays and LED lighting applications with constant-currentcontrol and open-load, shorted-load and overtemperature detection. It contains an 8-bit shiftregister and data latches that convert serial input data into parallel output format. At the outputstage, eight regulated current ports are designed to provide uniform, constant current for drivingLEDs within a wide range of VF variations.

Supplyand

Biasing

SerialInterface Logic

Constant-CurrentDrivers

Diagnosticsand

Protection

RegistersR-EXT

SDO

GND

CLK

SDILE

OE

VDDOUT1

OUT2

OUT3

OUT4

OUT5

OUT6

OUT7

OUT8

3 to 5.5 V

LED SupplyVoltage

up to 20 V

Micro-controller

TLC59xx

Reference

Key Features• Constant-output-current range: 5 mA to

120 mA• Programmable global current gain:

256 steps• Excellent output-current accuracy:

•• Between channels: < ±3% (max)•• Between ICs: < ±6% (max)

• Clock frequency: 30 MHz• Schmitt-trigger input• Supply voltage: 3.3 V or 5 V

8-Bit Constant-Current LED Sink Driver

TLC5917

Get samples and datasheets at: www.ti.com/sc/device/TLC5917-Q1


Power Management

PWM Power Supply Controllers/USB Power Switches

13

PWM Power Supply Controllers Selection GuideTypical Max OutputPower Max Supply UVLO: VREF Duty Voltage LeadingLevel Practical Start-Up Operating Voltage On/Off VREF Tol. Cycle Soft Feed- Edge Auto Qual

Device1 (W) Frequency Current Current (V) (V) (V) (%) (%) Start E/A Shutdown forward Blanking (Q1)Peak Current Mode ControllersUCC2800 10 to 200 1MHz 100µA 500µA 7.2 to 15 7.2/6.9 5 1.5 100 Yes Yes No No 100 ns YUCC2801 10 to 200 1MHz 100µA 500µA 9.4 to 15 9.4/7.4 5 1.5 50 Yes Yes No No 100 ns YUCC2802 10 to 200 1MHz 100µA 500µA 12.5 to 15 12.5/8.3 5 1.5 100 Yes Yes No No 100 ns YUCC2803 10 to 200 1MHz 100µA 500µA 4.1 to 15 4.1/3.6 4 1.5 100 Yes Yes No No 100 ns YUCC2804 10 to 200 1MHz 100µA 500µA 12.5 to 15 12.5/8.3 5 1.5 50 Yes Yes No No 100 ns YUCC2805 10 to 200 1MHz 100µA 500µA 4.1 to 15 4.1/3.6 4 1.5 50 Yes Yes No No 100 ns YUCC2808A-1/A-2 50 to 500 1MHz 130µA 1mA 4.3 to 15 12.5/8.34/4.1 — — Prog Yes Yes No No No YUCC2813-0 10 to 200 1MHz 100µA 500µA 7.2 to 15 7.2/6.9 5 1.5 100 Yes Yes No No 100 ns YUCC2813-1 11 to 200 1MHz 100µA 500µA 9.4 to 15 9.4/7.4 5 1.5 50 Yes Yes No No 100 ns YUCC2813-2 12 to 200 1MHz 100µA 500µA 12.5 to 15 12.5/8.3 5 1.5 100 Yes Yes No No 100 ns YUCC2813-3 13 to 200 1MHz 100µA 500µA 4.1 to 15 4.1/3.6 4 1.5 100 Yes Yes No No 100 ns YUCC2813-4 14 to 200 1MHz 100µA 500µA 12.5 to 15 12.5/8.3 5 1.5 100 Yes Yes No No 100 ns YUCC2813-5 15 to 200 1MHz 100µA 500µA 4.1 to 15 4.1/3.6 4 1.5 100 Yes Yes No No 100 ns YUCC2895 — 1MHz 150µA 5mA 9 to 17 11/9 5 1.2 100 Yes Yes No No No PreviewUCC28220 — 2MHz 200µA 3.5mA 8 to 14.5 10/8 — — 90 Yes No No No No PreviewUC2524A 50 to 500 450kHz 4mA 5mA 8 to 40 7.5/7 5 2 Prog Yes Yes Yes No No PreviewUC2825A — 1MHz 100µA — 22 16/10 5 1 50 Yes Yes No No Yes YUC2842A 30 to 350 500kHz 0.3mA 11mA 10 to 30 16/10 5 1.5 100 No Yes No Yes No NUC2843A 30 to 350 500kHz 0.mA 11mA 7.8 to 30 8.5/7.9 5 1.5 100 No Yes No Yes No YUC2844A 30 to 350 500kHz 0.3mA 11mA 10 to 30 16/10 5 1.5 50 No Yes No Yes No NUC2845A 30 to 350 500kHz 0.3mA 11mA 7.8 to 30 8.5/7.9 5 1.5 50 No Yes No Yes No NUC2856 — 1MHz — 18mA 7.7 to 40 7.7 5 1 50 Yes Yes Yes No No Preview

1The extra "C" in UCC means BiCMOS technology; therefore, UC2842 is bipolar and UCC2800 is BiCMOS.

USB Power Switches Selection GuideVIN VIN rDS(on) per Operating Continuous Current Limit Auto

(min) (max) FET (typ) Temp Range Current (max) (typ) Number of QualDevice (V) (V) (mΩ) Pin # / Pkg (°C) (A) (A) Switches Enable (Q1)TPS2022 2.7 5.5 33 8/SO –40 to 85 1 1.5 1 Low YTPS2024 2.7 5.5 33 8/SO –40 to 85 2 3 1 Low YTPS2030 2.7 5.5 33 8/SO –40 to 85 0.2 0.3 1 High YTPS2042B 2.7 5.5 70 8/SO –40 to 125 0.5 1 2 Low YTPS2051B 2.7 5.5 70 8/SO –40 to 125 0.5 1 1 High Y

USB Transient Voltage Suppressor Selection GuideSupply Number Peak Power Stand-off OperatingVoltage of USB Dissipation Voltage (min) Temp Range Auto Qual

Device (V) Ports (W) (V) (°C) Pin # / Pkg (Q1)SN652201 3.3 1 60 6 –40 to 85 6/SOT-23 Y

1USB 1.1 compatible.


Power Management

Supervisors/References

14

Supervisors Selection GuideIDD Time Manual Active-High Watchdog

Number of Supervised (typ) Delay Reset Reset Timer Auto QualDevice Supervisors Voltages Pin # / Pkg (µA) (ms) Input/MR Output WDI (Q1)TLC77xx 1 Adj./2.5/3.3/5.0 8/TSSOP 9 Prog — — YTPS3306 2 1.5/1.8/2.0/2.5/3.3 8/SO 15 100 — — YTPS3307 3 1.8/2.5/3.3 8/SO 40 200 — YTPS3803 1 Adj./1.5 5/SC-70 3 0.0055 — — YTPS3805 2 Adj./3.3 5/SC-70 3 0.0055 — — YTPS3808 1 Adj./3.0/3.3 SOT-23 3 Prog — — YTPS3809 1 2.5/3.0/3.3/5.0 3/SOT-23 9 200 — — — YTPS3813 1 2.25/2.64/2.93/4.55 6/SOT-23 9 25 — PreviewTPS3820/8-xx 1 3.3/5.0 5/SOT-23 15 25/200 — YTPS3823 1 2.5/3.0/3.3/5.0 5/SOT-23 15 200 — YTPS3824-xx 1 2.5/3.0/3.3/5.0 5/SOT-23 15 200 — YTPS3825-xx 1 3.3/5.0 5/SOT-23 15 200 — YTPS3836/8 1 1.8/2.5/3.0/3.3 5/SOT-23 0.25 10/200 — YTPS3837 1 1.8/2.5/3.0/3.3 5/SOT-23 0.25 10/200 — — YUCC2946 1 Adj. 8/TSSOP 12 Prog — Y

All devices feature an Active-Low Reset Output, except TPS3837.

References Selection GuideInitial Accuracy Temp Coeff IOUT/IZ Iq VI VI Operating

VO @ 25°C (max) (max) (max) (min) (max) Temp Range Auto QualDevice (V) (%) (ppm/°C) (mA) (µA) (V) (V) Pin # / Pkg (°C) (Q1)Low-Noise, Very Low-Drift, Precision Series Voltage ReferencesREF5020A 2.048 0.01 8 10 1000 2.7 18 8/SO –40 to 125 PreviewREF5025A 2.5 0.01 8 10 1000 2.7 18 8/SO –40 to 125 PreviewREF5030A 3 0.01 8 10 1000 3.2 18 8/SO –40 to 125 PreviewREF5040A 4.096 0.01 8 10 1000 4.296 18 8/SO –40 to 125 PreviewREF5045A 4.5 0.01 8 10 1000 4.7 18 8/SO –40 to 125 PreviewREF5050A 5 0.01 8 10 1000 5.2 18 8/SO –40 to 125 PreviewTL1431 2.5 to 36 0.4 — 100 2 2.49 2.51 8/SO –40 to 125 YTL431A 2.5 to 36 1 — — 0.5 2.47 2.52 3/SOT-23, 5/SOT-23 –40 to 125 YTL431B 2.5 to 36 0.5 — — 0.5 2.48 2.51 3/SOT-23 –40 to 125 YTL4050B 2.048 to 10 0.2 50 15 — — — 5/SC70 –40 to 125 Preview


Power Management

Power and Control

15

Power + Logic™: 8-Bit Devices Selection GuideVDS (max) ICC (typ) IO IPEAK rDS (on) (typ) EAS (max) tPLH (typ) ESD (max)

Device Description (V) (µA) (A) (A) (W) (mJ) (ns) (kV) Pin # / PkgTPIC6259 Addressable latch 45 15 0.25 0.75 1.3 75 625 3 20/SO (DW), 20/PDIP (N)TPIC6273 D-type latch 45 15 0.25 0.75 1.3 75 625 3 20/SO (DW), 20/PDIP (N)TPIC6595 Shift register 45 15 0.25 0.75 1.3 75 650 3 20/SO (DW), 20/PDIP (N)TPIC6596 Shift register 45 15 0.25 0.75 1.3 75 650 3 20/SO (DW), 20/PDIP (N)TPIC6A2591 Addressable latch 50 500 0.35 1.1 1 75 125 2.5 24/SO (DW), 20/PDIP (NE)TPIC6A5951 Shift register 50 500 0.35 1.1 1 75 125 2.5 24/SO (DW), 20/PDIP (NE)TPIC6B2592 Addressable latch 50 20 0.15 0.5 5 30 150 2.5 20/SO (DW), 20/PDIP (N)TPIC6B2732 D-type latch 50 20 0.15 0.5 5 30 150 2.5 20/SO (DW), 20/PDIP (N)TPIC6B5952 Shift register 50 20 0.15 0.5 5 30 150 2.5 20/SO (DW), 20/PDIP (N)TPIC6B5962 Shift register 50 20 0.15 0.5 5 30 150 2.5 20/SO (DW), 20/PDIP (N)TPIC6C5952 Sift register 33 20 0.1 0.25 7 30 80 2.5 16/SO (D), 16/PDIP (N), 16/TSSOP (PW)TPIC6C5962 Shift register 33 20 0.1 0.25 7 30 80 2.5 16/SO (D), 16/PDIP (N), 16/TSSOP (PW)TPIC28102 Shift register 40 620 0.1 0.21 5 — 1150 3 16/SO (D)

1Fault protection and diagnosis. 2Fault protection.

Mixed-Signal Power + Control Selection GuideVBAT Range VOS (max) ID/IPEAK rDS(on) (typ) Freq

Device Description (V) (V) (A) (W) (kHz) Pin # / PkgTPIC26031 6-channel serial interface low-side controller 5.5 to 25 68 0.35/2.25 0.7 4000 20/PDIP (NE), 24/SO (DW)

VBAT Range IBAT (typ) IGD (max) fOSC (typ) tr/tf (max)Device Description (V) (mA) (mA) (kHz) (µs) Pin # / PkgTPIC21012 DC brush motor controller 0 to 16 4 50 20 1/0.8 14/SO (D), 14/PDIP (N)

VCC Range VIT± (HL) Range I (LGX/UGX) (typ) fPWM (typ) fOSC/fOSC1 (max)Device Description (V) (mA) (mA) (kHz) (MHz) Pin # / PkgTPIC43T012 Three-phase DC brushless motor RPM controller 18 to 28 ±4 to ±12 ±10 22.7 10/10 38/TSSOP (DA)TPIC43T022 Three-phase DC brushless motor RPM controller 18 to 28 ±4 to ±12 ±10 22.7 10/10 38/TSSOP (DA)

VBAT Range VGATE Range IBAT (typ) fSCLK (max)Device Description (V) (V) (mA) (mHz) Pin # / PkgTPIC44H011 4-channel serial/parallel high-side FET pre-driver 8 to 24 VBAT+4 to VBAT+18 4 5 38/TSSOP (DA)TPIC44LO11 4-channel serial/parallel low-side FET pre-driver 8 to 24 7 to 13.5 0.5 10 24/SSOP (DB)TPIC44LO21 4-channel serial/parallel low-side FET pre-driver 8 to 24 7 to 13.5 0.5 10 24/SSOP (DB)TPIC44L031 4-channel serial/parallel low-side FET pre-driver 8 to 24 7 to 13.5 0.5 10 24/SSOP (DB)TPIC46L011 6-channel serial/parallel low-side FET pre-driver 8 to 24 7 to 13.5 0.5 10 24/SSOP (DB)TPIC46L021 6-channel serial/parallel low-side FET pre-driver 8 to 24 7 to 13.5 0.5 10 24/SSOP (DB)TPIC46L031 6-channel serial/parallel low-side FET pre-driver 8 to 24 7 to 13.5 0.5 10 24/SSOP (DB)

1Fault protection and diagnosis. 2Fault protection.

Peripheral Drivers and Actuators Selection GuideOutput Peak DelayVoltage Switching Output Drivers Time Operating(max) Voltage Current per Input (typ) Temp Range Auto Qual

Device Description (V) (V) (mA) Package Compatibility (ns) (°C) Pin # / Pkg (Q1)ULQ2003A High-voltage, high-current 50 50 500 7 CMOS, TTL 1000 –40 to 125 16/SO Y

Darlington transistor arrayULQ2004A High-voltage, high-current 50 50 500 7 CMOS 1000 –40 to 105 16/SO Y

Darlington transistor array


16 Interface

CAN/LIN

CAN/LIN Selection GuideHBM Maximum Bus Pin Typical

CAN/LIN Maximum Supply Maximum Bus Pin Loop Standoff ICC in Low- AutoPhysical Signaling Voltage Junction Temp ESD Delay Voltage Bus Power Mode Qual

Device Layer Standard Rate (V) TJ (°C) (kV) (ns) (V) Wake-Up (µA) (Q1) Pin # / PkgSN65HVD1040-Q1 ISO-11898-5 1Mbps 5 150 ±8 230 –27 to +40 Y 6 Y 8/SO (D)SN65HVD1050-Q1 ISO-11898-2 1Mbps 5 150 ±8 230 –27 to +40 N/A N/A Y 8/SO (D)SN65HVD1040V33-Q1 ISO-11898-5 1Mbps 5, 3.3 150 ±8 230 –27 to +40 Y 6 Preview 8/SO (D)SN65HVD251-Q1 ISO-11898-2 1Mbps 5 150 ±9 150 ±36 N 190 Y 8/SO (D)SN65HVD230Q-Q1 ISO-11898-2 1Mbps 3.3 150 ±15 135 –2 to +7 Y 370 Y 8/SO (D)SN65HVD231Q-Q1 ISO-11898-2 1Mbps 3.3 150 ±15 135 –2 to +7 N 0.1 Y 8/SO (D)SN65HVD232Q-Q1 ISO-11898-2 1Mbps 3.3 150 ±15 135 –2 to +7 N/A N/A Y 8/SO (D)TPIC1021 LIN 2.0 / 2.1 20kbps Vbat 150 ±12 N/A –40 to +40 Y 20 Y 8/SO (D)TPIC1021E-Q1 LIN 2.0 / 2.1 20kbps Vbat 150 ±12 N/A –40 to +40 Y 10 Preview 8/SO (D)

TI’s SN65HVD1040-Q1 EMC-optimized CAN transceiver provides a wide common-mode voltagerange and protection from cross-wire, overvoltage, loss-of-ground and overtemperature conditions.It also withstands significant voltage transients. Its ruggedness and signaling rates of up to 1 Mbps make the SN65HVD1040-Q1 ideal for automotive applications.

STB

RXD

TXD

CANH

CANL

SPLIT

Port x

RXD

TXD

8

1

4

2

37

5

6

GND

VBattery

VoltageRegulator

TPS7A6xxx-Q1

MCU(TMS470 Family)

VSUP

SN65HVD1040-Q1CAN

Transceiver

VCC

VCCVCC

Key Features• High speed (1 Mbps)• Compliant with ISO 11898-5• Ultralow-power standby mode with

wake up (<12 µA maximum)• Bus pin short-circuit protection:

–27 to +40 V• Unpowered node does not disturb bus• Dominant time-out protection• ESD protection up to ±8 kV (human-body

model) on bus pins

High-Speed CAN Transceiver with Wake Up

SN65HVD1040-Q1

Get samples and datasheets at: www.ti.com/sc/device/SN65HVD1040-Q1


Interface

LVDS, MLVDS, RS-485/422/232

17

LVDS Selection GuideNo. No. Signal Tx tpd Rx tpd ICC ESD Supplyof of Input Output Rate (typ) (typ) (max) HBM Voltage Auto Qual

Device Description Tx Rx Signal Signal (Mbps) (ns) (ns) (mA) (kV) (V) (Q1)LVDSSN65LVDS1 Single LVDS transmitter 1 — LVTTL LVDS 630 1.7 — 8 15 3.3 NSN65LVDS2 Single LVDS receiver — 1 LVDS LVTTL 400 — 2.6 7 15 3.3 NSN65LVDS180 Single full-duplex LVDS transceiver 1 1 LVTTL, LVDS LVTTL, LVDS 400 1.7 3.7 12 12 3.3 YSN65LVDS051 Dual LVDS transmitter/receiver 2 2 LVDS, LVTTL LVDS, LVTTL 400 1.7 3.7 20 12 3.3 YSN65LVDS84A FlatLink™ transmitter 3 — LVDS LVDS 197 4.5 — 35 4 3.3 YSN65LVDS86A FlatLink receiver — 3 LVDS LVDS 163 — 5 68 4 3.3 YSN65LVDS95 LVDS SerDes transmitter 3 — LVDS LVDS 170 4.2 — 110 6 3.3 YMLVDSSN65LVDM050 Dual LVDM transmitter/receiver 2 2 LVTTL, LVDM LVTTL, LVDM 500 1.7 3.7 27 12 3.3 YSN65LVDM051 Dual LVDM transmitter/receiver 2 2 LVTTL, LVDM LVTTL, LVDM 500 1.7 3.7 27 12 3.3 Y

RS-485/422/232 Selection GuideTemperature Supply Signaling Rate ICC (max) ESD Auto QualPrefix Device No. of Tx No. of Rx Voltage (V) (Mbps) (mA) (kV) Footprint (Q1)SN75 176A 1 1 5 10 50 2 SN75176 NSN65, SN75 176B 1 1 5 10 70 2 SN75176 NSN75 178B 1 1 5 10 70 2 SN75176 NSN75 179B 1 1 5 10 70 2 SN75179 NSN55, SN65, SN75 LBC176 1 1 5 10 1.5 2 SN75176 YSN65, SN75 LBC176A 1 1 5 30 15 12 SN65176 NSN65, SN75 LBC179 1 1 5 10 5 2 SN75179 NSN65, SN75 LBC179A 1 1 5 30 15 16 SN75179 NSN65, SN75 LBC180 1 1 5 10 5 2 SN75LBC180 NSN65, SN75 LBC180A 1 1 5 30 15 12 SN75180 NSN65 C3221 1 1 3.3 or 5 1 1 15 SN75C3221 YMAX3238 — 5 3 3.3 or 5 0.25 2 15 — Y


18 Data Converters/Audio

Data Converters/Audio

ADCs Selection GuideNo. of Power No Analog Analog

Sample Input Consumption DNL INL Missing Voltage Voltage Logic Voltage Logic Voltage AutoResolution Rate Channels (typ) (max) (max) Codes AV/DD (min) AV/DD (max) DV/DD (min) DV/DD (max) Input Qual

Device (Bits) (max) Architecture (SE) (mW) (±LSB) (±LSB) (Bits) (V) (V) (V) (V) Type Pin # / Pkg (Q1)ADS5204 10 40MSPS Pipeline 2 275 1 1.5 10 0 3.6 0 3.6 Voltage 48/TQFP YTLC2543 12 66kSPS SAR 11 5 1 1 12 4.5 5.5 4.5 5.5 Voltage 20/SOP YTLV1548 10 85kSPS SAR 8 — 1 1 10 2.7 5.5 2.7 5.5 Voltage 20/SOP YTLV2553 12 200kSPS SAR 11 2.43 1 1 12 2.7 5.5 2.7 5.5 Voltage 20/SO, Preview

20/TSSOPTLV5535 8 35MSPS Pipeline 1 106 2.4 2.4 — 3 3.6 3 3.6 Voltage 28/TSSOP Y

Class-D Audio Amplifiers Selection GuideHalf Power Iq per

Output THD + N channel Operating AutoPower Supply @ 1 kHz (%) (typ) ISD PSRR Temp Range Qual

Device Description (W) (V) (kHz) (mA) (µA) (dB) (°C) Pin # / Pkg (Q1)TPA2000D1 Mono filter-free class-D audio amplifier 2 2.7 to 5.5 0.2 4 0.05 77 –40 to 105 16/TSSOP YTPA2005D1 1.4-W mono filter-free class-D audio 1.18 2.5 to 5.5 0.2 2.8 0.5 75 –40 to 85 8/SON Y

power amplifier

Codecs Selection GuideNo. of Sampling SNR DAC/ Digital PD Analog Digital Operating AutoDACs/ Rate (max) Resolution ADC (typ) Audio Control (typ) Supply Supply Temp Qual

Device Description ADCs (kHz) (Bits) (dB) Interface Interface (mW) (V) (V) Range (°C) Pin # / Pkg (Q1)TLV320AIC23B Stereo audio codec, 8- to 96-kHz, 2/2 96 24 100 / 90 L, R, I2S, DSP SPI, I2C 23 2.7 to 3.6 1.42 to 3.6 –40 to 85 28/TSSOP Y

with integrated headphone ampTWL1103T Voice-band audio processor (VBAP) — — 15 — — I2C — 2.7 to 3.3 2.7 to 3.3 –40 to 105 32/TQFP Y


Design Support 19

TI’s Analog eLab™ Design Center Can Help You with All Your Design Needs

LEARN from TI experts to solve your real-world design problems

SELECT the right TI product for your design using tools to narrow your choices based on your criteria

DESIGN circuits quickly using recommendations for circuit topologies and TI’s reference designs

SIMULATE using downloadable SPICE and IBIS models for a working simulation environment

SAMPLE various analog products and receive within 24 hours

Texas Instruments

Design CenterAnalog

TM

www.ti.com/analogelab

Receive Updates on TI’s Solutions for Automotive Applications

By registering with my.TI andtelling us your areas of interestby application, product, etc.,you can receive the latestinformation valuable to you. Toreceive automotive updates,be sure to select “Automotive”under “Edit Areas of Interest”.

PRSRT STDU.S. POSTAGE

PAIDDALLAS, TEXAS

PERMIT NO. 2758

Texas Instruments Incorporated

14950 F.A.A. Blvd.

Fort Worth, Texas 76155

Address service requested

SGZB002D

Amplifier and Data ConverterAnalog SwitchClocks and TimingDSPInterface

LogicLow-Power RFMSP430Power Management

To download these guides, please visit:www.ti.com/selection

IMPORTANT NOTICETexas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers shouldobtain the latest relevant information before placing orders and should verify that such information is current and complete. All products aresold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standardwarranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except wheremandated by government requirements, testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products andapplications using TI components. To minimize the risks associated with customer products and applications, customers should provideadequate design and operating safeguards.TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Informationpublished by TI regarding third-party products or services does not constitute a license from TI to use such products or services or awarranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectualproperty of the third party, or a license from TI under the patents or other intellectual property of TI.Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompaniedby all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptivebusiness practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additionalrestrictions.Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids allexpress and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is notresponsible or liable for any such statements.TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonablybe expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governingsuch use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, andacknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their productsand any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may beprovided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products insuch safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products arespecifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet militaryspecifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely atthe Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products aredesignated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designatedproducts in automotive applications, TI will not be responsible for any failure to meet such requirements.Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers amplifier.ti.com Audio www.ti.com/audioData Converters dataconverter.ti.com Automotive www.ti.com/automotiveDSP dsp.ti.com Broadband www.ti.com/broadbandClocks and Timers www.ti.com/clocks Digital Control www.ti.com/digitalcontrolInterface interface.ti.com Medical www.ti.com/medicalLogic logic.ti.com Military www.ti.com/militaryPower Mgmt power.ti.com Optical Networking www.ti.com/opticalnetworkMicrocontrollers microcontroller.ti.com Security www.ti.com/securityRFID www.ti-rfid.com Telephony www.ti.com/telephonyRF/IF and ZigBee® Solutions www.ti.com/lprf Video & Imaging www.ti.com/video

Wireless www.ti.com/wireless

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265Copyright 2008, Texas Instruments Incorporated

analog automotive guide - texas instruments

Documents