ams® flange boss™ procedures
TRANSCRIPT
![Page 1: AMS® FLANGE BOSS™ Procedures](https://reader034.vdocuments.us/reader034/viewer/2022050907/55a81fbe1a28ab16188b4627/html5/thumbnails/1.jpg)
FLANGE BOSS™ SPREADER
INSTRUCTIONS
![Page 2: AMS® FLANGE BOSS™ Procedures](https://reader034.vdocuments.us/reader034/viewer/2022050907/55a81fbe1a28ab16188b4627/html5/thumbnails/2.jpg)
Follow all plant safety procedures, including permits to open flanges.
Check and be certain no pressure exists and process material has been drained
before opening flanges.
If line pressure exists or process material is present, follow plant safety procedure
to remove before opening any flanges.
![Page 3: AMS® FLANGE BOSS™ Procedures](https://reader034.vdocuments.us/reader034/viewer/2022050907/55a81fbe1a28ab16188b4627/html5/thumbnails/3.jpg)
Select correct Flange Boss for flange rating. In many situations
2 Flange Boss Spreaders should be used.
FBX-150-300 fits 150 lb - 300 lb ANSI flanges from ½” to 24”
FBX-400-600 fits 400 lb - 600 lb ANSI flanges from ½” to 24”
FBX-900-2500 fits 900 lb - 1500 lb ANSI flanges from ½” to 24”
2500 lb flanges from ½” to 12” including ring joint flanges
![Page 4: AMS® FLANGE BOSS™ Procedures](https://reader034.vdocuments.us/reader034/viewer/2022050907/55a81fbe1a28ab16188b4627/html5/thumbnails/4.jpg)
Remove only the necessary bolts to complete the work.
![Page 5: AMS® FLANGE BOSS™ Procedures](https://reader034.vdocuments.us/reader034/viewer/2022050907/55a81fbe1a28ab16188b4627/html5/thumbnails/5.jpg)
Make sure the nuts on the remaining bolts are
loosened enough to make the spread.
Locate the bolt hole where the Flange Boss™
spreader will be installed.
Loosen all bolts
![Page 6: AMS® FLANGE BOSS™ Procedures](https://reader034.vdocuments.us/reader034/viewer/2022050907/55a81fbe1a28ab16188b4627/html5/thumbnails/6.jpg)
Make sure the nuts on the remaining bolts are
loosened enough to make the spread.
Locate the bolt hole where the Flange Boss™
spreader will be installed.
Loosen all bolts
![Page 7: AMS® FLANGE BOSS™ Procedures](https://reader034.vdocuments.us/reader034/viewer/2022050907/55a81fbe1a28ab16188b4627/html5/thumbnails/7.jpg)
Make sure the nuts on the remaining bolts are
loosened enough to make the spread.
Locate the bolt hole where the Flange Boss™
spreader will be installed.
Loosen all bolts
![Page 8: AMS® FLANGE BOSS™ Procedures](https://reader034.vdocuments.us/reader034/viewer/2022050907/55a81fbe1a28ab16188b4627/html5/thumbnails/8.jpg)
Make sure the nuts on the remaining bolts are
loosened enough to make the spread.
Locate the bolt hole where the Flange Boss™
spreader will be installed.
Loosen all bolts
![Page 9: AMS® FLANGE BOSS™ Procedures](https://reader034.vdocuments.us/reader034/viewer/2022050907/55a81fbe1a28ab16188b4627/html5/thumbnails/9.jpg)
Make sure the nuts on the remaining bolts are
loosened enough to make the spread.
Locate the bolt hole where the Flange Boss™
spreader will be installed.
Loosen all bolts
![Page 10: AMS® FLANGE BOSS™ Procedures](https://reader034.vdocuments.us/reader034/viewer/2022050907/55a81fbe1a28ab16188b4627/html5/thumbnails/10.jpg)
Make sure the nuts on the remaining bolts are
loosened enough to make the spread.
Locate the bolt hole where the Flange Boss™
spreader will be installed.
Locate a bolt hole to install tool
![Page 11: AMS® FLANGE BOSS™ Procedures](https://reader034.vdocuments.us/reader034/viewer/2022050907/55a81fbe1a28ab16188b4627/html5/thumbnails/11.jpg)
Connect the Flange Boss™ with the flange pin.
Refer to flange pin tag for proper flange bolt sizes.
Push tool link against flange on both sides
![Page 12: AMS® FLANGE BOSS™ Procedures](https://reader034.vdocuments.us/reader034/viewer/2022050907/55a81fbe1a28ab16188b4627/html5/thumbnails/12.jpg)
Lubricate cam-wedge and flange surfaces for easier
use.
lubricate
![Page 13: AMS® FLANGE BOSS™ Procedures](https://reader034.vdocuments.us/reader034/viewer/2022050907/55a81fbe1a28ab16188b4627/html5/thumbnails/13.jpg)
Rotate cam-wedge into flange gap. Make sure that
the cam wedge is rotated in the correct direction
(narrow end first).
Rotate into Gap
![Page 14: AMS® FLANGE BOSS™ Procedures](https://reader034.vdocuments.us/reader034/viewer/2022050907/55a81fbe1a28ab16188b4627/html5/thumbnails/14.jpg)
The cam-wedge can be rotated with either a breaker-
bar or impact tool or hydraulic tool.
Mechanical, pneumatic or hydraulic tool
![Page 15: AMS® FLANGE BOSS™ Procedures](https://reader034.vdocuments.us/reader034/viewer/2022050907/55a81fbe1a28ab16188b4627/html5/thumbnails/15.jpg)
Rotate until safety stop indicator nears flange and
flange is spread. Do not over rotate and damage
safety stop indicator.
Rotate
![Page 16: AMS® FLANGE BOSS™ Procedures](https://reader034.vdocuments.us/reader034/viewer/2022050907/55a81fbe1a28ab16188b4627/html5/thumbnails/16.jpg)
As a precaution a Block Boss™ should be installed
to prevent accident flanges closures
Block Boss™
![Page 17: AMS® FLANGE BOSS™ Procedures](https://reader034.vdocuments.us/reader034/viewer/2022050907/55a81fbe1a28ab16188b4627/html5/thumbnails/17.jpg)
AMS® American Maintenance Systems
12407 N. Mopac Expwy, Suite 250-469
Austin, Texas 78758 USA
Telephone 512 238 0962
Fax 512 238 0961
Email [email protected]
www.american-maintenance-systems.com
Copyright AMS® 2009