amplitude modulation transmission
TRANSCRIPT
![Page 1: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/1.jpg)
Amplitude Modulation (AM) Transmission
![Page 2: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/2.jpg)
AM Transmission
• Signals are transmitted between a transmitter over some form of transmission medium
• But normally signals are not in the form that is suitable for transmission and need to be transformed
• Modulation is a process of impressing (applying) a low frequency information signals onto a relatively high frequency carrier signal
![Page 3: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/3.jpg)
Principles of AM
• Amplitude Modulation - is a process of changing the amplitude of a relatively high frequency carrier signal with the instantaneous value of the modulating signal (information signal).
• 2 inputs to the modulation devise (modulator)
A single, high frequency RF carrier signal of constant amplitude.
Low frequency information signals that maybe a single frequency or a complex waveform made up of many frequencies.
![Page 4: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/4.jpg)
• In the modulator, the information signal modulates the RF carrier signal to produce a modulated waveform made up of many frequencies. This modulated waveform also called as AM envelope.
![Page 5: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/5.jpg)
AM Envelope The most commonly used AM
modulation technique is the AM double- sideband full carrier (DSBFC) scheme.
Given a signals representation as follow,
• Carrier signal = Vc sin [2 fc t ]
• Modulating signal = Vm sin [2 fm t ]
• Modulated wave = Vam [t ]
When a modulating signal (information signal) is applied to the carrier signal, the amplitude of the output wave varies in accordance with the modulating signal
![Page 6: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/6.jpg)
AM Frequency Spectrum and Bandwidth • Output envelop is a complex wave made
up of a DC voltage, the carrier frequency, sum frequencies (fc + fm) and difference frequencies (fc -fm).
• The sum and difference frequencies are displaced from carrier frequency by an amount equal to modulating frequency.
• The AM signal spectrum contains frequency components spaced fm Hz on either side of the carrier as shown in figure 4-2.
![Page 7: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/7.jpg)
The AM spectrum ranges from fc - fm(max) to fc + fm(max).
Parameters : Lower sideband (LSB) = band of frequencies between
fc -
fm(max) and fc Lower side frequency (LSF) = any frequency within LSB Upper sideband (USB) = band of frequencies between fc and fc +
fm(max) Upper side frequency (USF) = any frequencies within USB
Bandwidth : twice the highest modulating signal frequency
B = 2 fm(max)
![Page 8: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/8.jpg)
Phasor Representation of an Amplitude-Modulation Wave
• AM envelope is produced from the vector addition of the carrier and the upper and lower side frequencies.
• The two side frequencies combine and produce a resultant components that combines with the carrier vector .
![Page 9: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/9.jpg)
Coefficient of Modulation and Percent Modulation
Coefficient of Modulation is a term used to describe the amount of amplitude change presents in an AM waveform.
Percent Modulation is the coefficient of modulation stated as a percentage.
![Page 10: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/10.jpg)
Mathematical representation :
• m= (1)
• M = ×100= m×100 (2)
Where:
m = modulation coefficient where usually
0 < m 1
M = percent modulation
= peak change in the amplitude of the
output waveform
= peak amplitude of the unmodulated
carrier waveform
![Page 11: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/11.jpg)
Graphical representation of the relationship between m, and .
Based from the above figure, = ( ) (3) = ( + ) (4)
![Page 12: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/12.jpg)
M = 100
= 100 (5)
can also be defined as the sum of voltages from upper and lower side frequencies.
= (6)
(7)
![Page 13: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/13.jpg)
Therefore,
(8)
Where:
= peak amplitude of the upper side frequency (volts)
= peak voltage of the lower side frequency (volts)
![Page 14: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/14.jpg)
![Page 15: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/15.jpg)
Ex : For the AM waveform shown below, determine
a) Peak amplitude of the upper and lower side frequencies
b) Peak amplitude of the unmodulated carrier
c) Peak change in the amplitude of the envelope
d) Coefficient of modulation Percent modulation
![Page 16: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/16.jpg)
AM Voltage Distribution and Analysis The amplitude of the AM wave varies in proportional to the amplitude of the modulating signal and the maximum amplitude of the AM wave is + .
Given the unmodulated carrier signal as
(t) = sin (2t) (9)
Where:
(t) = time-varying voltage waveform for the carrier
= peak carrier amplitude (volts)
= carrier frequency (hertz)
![Page 17: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/17.jpg)
Based on the following characteristics of the AM wave :
• the repetition rate of an AM envelope is equal to the frequency of the modulating signal
• the amplitude of the AM wave varies proportional to the amplitude of the modulating signal
• the maximum amplitude of the modulated wave is equal to +
![Page 18: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/18.jpg)
therefore, the output modulated wave can be expressed as
(t ) = [ + sin ( 2t )][sin (2t )] (10)
Where:
[ + sin ( 2t )] = amplitude of the modulated wave
= peak carrier signal amplitude
= carrier signal frequency
= modulating signal frequency
= peak modulated output signal amplitude
![Page 19: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/19.jpg)
substituting (1) into (10),
(t) = [+ sin(2t )][sin (2t )] (11)
rearranging equation (11), we get
(t) = [1 + m sin(2t )] [ sin (2t )] (12)
Where:
[1 + m sin(2t )] = constant + modulating signal
[ sin (2t )] = unmodulated carrer
(t) = sin (2t )+[ sin(2t)][sin(2t )] (13)
![Page 20: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/20.jpg)
Then by using a trigonometric function, equation (13) can be represented as, ( t ) = sin (2t ) cos [2 ( + )t ] + cos [2 ( )t ] (14)
Where:
sin (2t ) = carrier signal (volts)
cos [2 ( + )t ] = upper side frequency signal (volts)
+ cos [2 ( )t ] = lower side frequency signal (volts)
![Page 21: Amplitude Modulation Transmission](https://reader036.vdocuments.us/reader036/viewer/2022081419/554a2f2bb4c90542548b532a/html5/thumbnails/21.jpg)
From equation (14) there are few characteristics of AM DSBFC that can be deduced as follow :
1. the amplitude of the carrier signal is unaffected by the modulation process.
2. the amplitude of USF and LSF depends on both the carrier amplitude and the coefficient of modulation.
3. for 100% modulation (m = 1) and from previous section,