your connectivity partner. locations main office: high tech products lallio, italy usa office: htp...

Your Connectivity Partner

Locations

Main Office:High Tech Products

Lallio, Italy

USA Office:HTP ConnectivityParsippany, NJ

Locations

Manufacturing:HTP CHINA LTD

Guangdon Province, China

DIN 43650 Moulded Assemblies & Connectors

DIN 43650

Typically used to electrically connect hydraulic & pneumatic solenoids, filter & pressure switches and sensors

This connector group is used by the majority of valve manufacturers

DIN 43650 Molded Assemblies

Saves installation time and expense

Available in any length, in all 5 DIN 43650 types

With or without light indication and surge suppression

For 24, 110 & 220 volt applications

DIN 43650 Connectors

Provides a greater range of connectors then offered by the valve manufacturers

Circuits available include– Without components– LED Only– Varistor & LED– Diode & LED

For 24, 110 & 220 volt applications

M12 to DIN 43650

Typically used to connect solenoid valves or sensors to distribution boxes

All DIN 43650 types available With or without LED and

Suppression .5 Meter standard cable

length (other lengths available upon request)

3

41

2

5

DIN Double Y Cable

Used to double the outputs from a Distribution Box

Available in all the DIN43650 Connector Types

With or without LED & Suppression

DIN Triple Y Cable

Used to provide multiple outputs from a single M12 connector

Available in all the DIN43650 Connector Types

With or without LED & Suppression

Multiple Connector Assemblies

Up to 10 connectors

with 1 cable One individual to

each connector Common negatives

and grounds (on 2

position)

DIN 43650 to M12 Connector

Allows connection to a DIN43650A or DIN43650B valve with an M12 Connector

Available also with different circuit

New Big DIN 43650A

Separate circuit board allow larger components to be used

DIN Male Panel Mount (Basis)

Male DIN43650 connectors For panel and special

mounting

Special Industrial Connector

15mm X 15mm with 4 diagonal pins

DIN Extension Cables

Female to Male Connections

Allows DIN43650 Cable to be Extended

Available in all DIN Types

In Line Cycle Timer – Now Available

The HTP in-line timer is designed to cycle power on and off, to either pneumatic or hydraulic solenoid valves.

Typical applications include draining water from compressor tanks, periodic product sampling, and control of lubricating or irrigation systems.

Plugs in-line between male & female connectors

Works with any voltage from 24 to 240 VAC/DC

ON – 0.5 to 10 sec OFF – 0.5 to 45 min For pneumatic or hydraulic solenoid

valves ON and OFF LED status indication Manual push button override

New Products – Now Available

Industrial Form B Molded Assemblies with Dual Ground Pins

Works with both ground down and ground up cable positions

M12 Connectors and Molded Assemblies

M12 Connector Wiring

3 Pole Versions– 1 = Positive– 3 = Negative– 4 = Signal

4 Pole Versions– 1 = Positive– 3 = Negative– 2 = Signal 1– 4 = Signal 2

5 Pole Versions– 1 = Positive– 3 = Negative– 2 = Signal 1– 4 = Signal 2– 5 = Ground

M a l e F r o n t V i e w

4 - S i g n a l

1 - P o s i t i v e

3 - N e g a t i v e

F e m a l e F r o n t V i e w

4 - S i g n a l

1 - P o s i t i v e

3 - N e g a t i v e

2 - S i g n a l 2 - S i g n a l

M12 Connectors are a very popular way to connect sensors & switches.Changing a sensor or switch is much faster when a connector is used,reducing down time and labor expense.

M12 Connector Assemblies

3, 4, 5, 8 or 12 pole versions Male or female Straight or right angle Single or Double Ended PVC, Shielded or PUR cable

(other cable available on request)

Standard Length 3 meters (1meter for double ended)

2 or 3 LED’s for PNP or NPN switch indication

NEW – Fully Shielded Versions Available

M12 “T” Connectors

“T” connectors are designed to expand the ports on hard wired distribution boxes, by splitting the two individual wires into two connectors

NEW – Transparent “T” With Light Indication

M12 Y Cable

Can be used to double the capacity of an M12 Distribution Box, by splitting the individual inputs

M12 Triple Y Cable

Used to provide multiple outputs from a single M12 connector

M12 Field Wire Connectors

4, 5, or 8 pole versions Screw terminals Straight or right angle Single or dual cable entry

M12 Field Wire Connectors

NEW!! 12 pole versions

Metal Field Wire M12 Connector

Housing in Nickel Plated Brass

For Tough Environments Rated IP 67 Completely Shielded

M12 Panel Mount Connectors

4, 5, 8 or 12 pole versions Female or male

connectors Front or back mounting Solder or PCB

connections or pre-wired

M8 Connectors and Assemblies

M8 Connector Wiring

3 Pole Versions– 1 = Positive– 3 = Negative– 4 = Signal

4 Pole Versions– 1 = Positive– 3 = Negative– 2 = Signal 1– 4 = Signal 2

M a l e F r o n t V i e w F e m a l e F r o n t V i e w

3 - N e g a t i v e 3 - N e g a t i v e

4 - S i g n a l 4 - S i g n a l

1 - P o s i t i v e 1 - P o s i t i v e

M a l e F r o n t V i e w F e m a l e F r o n t V i e w 4 - S i g n a l

3 - N e g a t i v e 1 - P o s i t i v e

2 - S i g n a l 4 - S i g n a l 2 - S i g n a l

3 - N e g a t i v e 1 - P o s i t i v e

M8 Connectors are a very popular way to connect sensors & switches.Changing a sensor or switch is much faster when a connector is used,reducing down time and labor expense.

M8 Connector Assemblies

3 or 4 pole versions Male or female Straight or right angle Single or Double Ended PVC, Shielded or PUR cable Standard Length 3 meters

(1meter for double ended) 2 LED’s for PNP or NPN

switch indication NEW – Fully Shielded

Versions Available

M8 “Y” Assemblies

Both the “Y” assemblies are designed to expand the ports on hard wired distribution boxes, by splitting the two individual wires into two connectors

M8 Field Wire Connectors

3 or 4 pole versions Solder or screw

terminals Straight

M8 Panel Mount Connectors

3 or 4 pole versions Female or male

connectors Front mounting Solder or PCB

connections or pre-wired

M12 Distribution Boxes

Distribution Boxes

Distribution Boxes eliminate the need to run multiple cables back to the control panel and create a “plug and play” system

They can be used for both input & output devices Commons within the box reduces wiring time at the

control panel Distribution Boxes are designed around the

standard wiring used for the connectors. Common wiring (to each connector position) is provided for positive, negative and ground positions. Each connector has 2 individual wires available to transfer NO & NC position status for input devices or one wire can be used to provide separate power for output devices

M12 Distribution Boxes – Field Wire

5 pole M12 connector 4, 6 or 8 ports Self wire or molded main

cable With or without LED

indication for PNP or NPN sensors 4 - I n d i v i d u a l S i g n a l ( N O o r P o w e r )

3 - C O M M O N N e g a t i v e

5 - C O M M O N G r o u n d

2 - I n d i v i d u a l S i g n a l ( N C )

1 - C O M M O N P o s i t i v e

M12 Distribution Boxes – Triple signal

5 pole M12 connector 4 or 8 ports Self wire or molded main

cable Without LED indication

for PNP or NPN sensors

M12 Distribution Boxes – Molded Cable

5 pole M12 connector 4, 6 or 8 ports Molded main cable in 5,

10 or 15 meters With or without LED

indication for PNP or NPN sensors

4 - I n d i v i d u a l S i g n a l ( N O o r P o w e r )

3 - C O M M O N N e g a t i v e

5 - C O M M O N G r o u n d

2 - I n d i v i d u a l S i g n a l ( N C )

1 - C O M M O N P o s i t i v e

Magnetic Sensors

For use with aluminum cylinders with target magnetic

Available in dry contact (reed switches) or solid state (PNP or NPN)

With many different mounting and body styles

With molded cable, M12 or M8 connection

New Products – Now Available

7/8 “MINI CHANGE” – 3, 4 and 5 poles

New Products – Now Available

7/8 “MINI CHANGE” male / female 3, 4 and 5 poles

Fieldwire connectors

New Products – Now Available

7/8 “MINI CHANGE” male / female 3, 4 and 5 poles

Molded cable

New Products – Now Available

7/8 “MINI CHANGE” male / female 3, 4 and 5 poles

Panel mount

New Product – now available

7/8 “MINI CHANGE” male / female 3, 4 and 5 poles

T-splitter

New Products – Now Available

M8 Distribution Boxes6 – 8 – 10 Positions

Terminal Blocks

New Products – Now Available

M8 Distribution Boxes6 – 8 – 10 – 12 Positions

Molded cable

New Products – Now Available

M8 Distribution Boxes6 – 12 Positions

M12 with 8 pole connector

New Products in Development

M16 & M23 Connectors and Assemblies

Thank-you!