weidmuller klippon tb enclosures
Post on 26-Nov-2014
211 Views
Preview:
TRANSCRIPT
Klippon® TB – Steel EnclosuresProduct Information
3
Contents
Klippon® TB – Steel Enclosures
Introduction 4 Technical Information
Klippon® TB10 • 229mm x 152mm x 133mm 16
Klippon® TB10A •260mm x 260mm x 150mm 17 • 260mm x 260mm x 200mm
Klippon® TB11 •306mm x 306mm x 150mm 18 •306mm x 306mm x 200mm
Klippon® TB11A •350mm x 260mm x 150mm 19 • 350mm x 260mm x 200mm
Klippon® TB11B •450mm x 400mm x 150mm 20 • 450mm x 400mm x 200mm
Klippon® TB12 •458mm x 382mm x 150mm 21 • 458mm x 382mm x 200mm
Klippon® TB12A •480mm x 480mm x 150mm 22 • 480mm x 480mm x 200mm
Klippon® TB12B •550mm x 350mm x 150mm 23 • 550mm x 350mm x 200mm
Klippon® TB12C •458mm x 300mm x 150mm 24 • 458mm x 300mm x 200mm
Klippon® TB12D •620mm x 450mm x 150mm 25 • 620mm x 450mm x 200mm
Klippon® TB13 •762mm x 508mm x 150mm 26 • 762mm x 508mm x 200mm
Klippon® TB14 •914mm x 610mm x 150mm 27 • 914mm x 610mm x 200mm
Compression Control / 6 Silicone Gaskets
Moisture / Dust Channel 7
Internal Pillar Location 8
Gland Plates 9
Hinges 10
Earth Studs 11
Identification Label Holder 12 Weidmüller Service 28
Technical Overview 14 Industry Segments 31
4
Harmonisation – the key to market success!
Until quite recently ATEX was recognised as the European standard and IEC as the non-European standard for Hazardous Area Equipment.
The Klippon® TB is one of the first enclosures to offer component approval and certification against the newly released IEC / EN 60079 series of standards, which finally present a harmonised approach to the design and construction of equipment intended for use in Hazardous Areas.
Klippon® TB overview
The name Klippon® has long been synonymous with the supply of terminals and enclosures for use in both industrial and hazardous area (Ex) markets. Klippon® is a trade name of the international Weidmüller Group of companies which has sales, production facilities and agents in over 70 countries world-wide.
In fiscal 2006, Weidmüller generated sales of € 443 million and currently employs some 3,000 people world-wide.
Weidmüller started manufacturing enclosures in the 1960’s. Since then our reputation as a competent and reliable partner has been demonstrated on many occasions and this is reinforced by our innovatively designed products that meet the most demanding market requirements.
This experience has been utilised in the design of the New Klippon® TB range, which has been built to withstand the harshest environments. This range of enclosures offers improved on-site accessibility coupled with many more design improvements.
The Klippon® TB range delivers outstanding performance in the severest conditions and meets the needs of the increasingly demanding world-wide environments. As more and more areas fall under the world-wide hazardous area legislation you need an enclosure that is designed to meet these increasingly stringent requirements.
Introduction
5
Introduction
Fixing Bolt Earth StudGland Plates Gland PlatesHinge pin
Silicone Gaskets Gasket Compression Control
Internal Pillar
Moisture /Dust Channel
5
Klippon® TB features overview
6
Klippon® TB – Key Features
Gasket compression control has been incorporated throughout the design of the enclosure. Over compression of gaskets leads to the collapse of the cellular structure and results in loss of the IP rating.
The Klippon® TB features a broad lip around the aperture of the enclosure. This eliminates knife-edge contact, preventing damage to the cellular structure of the gasket. Silicone gasket material is standard across the New Klippon® TB range; offering improved temperature characteristics and resistance to chemical attack.
Compression Control / Silicone Gaskets
7
Klippon® TB – Key Features
The Moisture / Dust Channel runs around the aperture of the body of the enclosure. This ensures that any debris / moisture present on the surface of the enclosure will not enter the enclosure when the lid is opened.
Moisture / Dust Channel
8
Klippon® TB – Key Features
The position of the internal mounting pillars has been optimised to allow the greatest size of mounting plate / assembly rail to be utilised, whilst still allowing full accessibility for tooling.
In addition, the diameter of the pillar has been increased, offering greater clamping stability.
Internal Pillar Location
9
Klippon® TB – Key Features
The dimensions of the gland plates have been optimised to allow the greatest number of entries for each size of enclosure. Weidmüller offer gland plates in 3 mm thick material as standard and 6 mm as an option for applications where tapped entries are required.
The new Klippon® TB range of enclosures is available with 1, 2, 3 or 4 gland plates.The gland plates incorporate rounded corners offering protection against injury.
Gland Plates
10
Klippon® TB – Key Features
The hinge pin is designed to prevent accidental removal of the lid whilst allowing removal without the need for tooling.
Captive hinge pins prevent loose parts being lost in the field. The hinge system also allows the lid to be opened by up to 170 degrees, for ease of access.
Hinges
11
Klippon® TB – Key Features
Earth studs are equipped with a sealing mechanism and are keyed to prevent rotation.
An M10 Internal / External earth stud is fitted as standard – M12, M14 and M16 are also available as option.
Earth Studs
12
Klippon® TB – Key Features
A drop-in label holder (illustrated below) is available as an option, incorporating features to locate and retain the label once it has been inserted.
This feature allows labels to be retro-fitted by users onsite (post installation) without compromising the ingress protection of the enclosure.
The information panel pictured (below) indicates the ATEX markings, the enclosure serial numbers and the maximum dissipated power as required.
Identification Label Holder
PART NUMBER 0929140000DESCRIPTION KLIPPON TB11 303015B3STAG REFERENCE TB1 / 06 / 01
13
14
Technical Overview
Technical Overview
Overview of enclosures
Features
• Electropolished 316L stainless steel or painted sheet steel (RAL 7032)
• With 1, 2, 3 or 4 gland plates; optionally without gland plates
• Fully detachable lid
• Approved to the latest international standards (e.g. ATEX, IEC Ex)
Note: The Weidmüller Customer Specific Assembly Service can create pre-assembled enclosures to your unique specification.
Technical Information
Enclosure material Mild steel 1.0330 or stainless steel 1.4404 (316L) 1.50 mm
Gland plate material Mild steel 1.0330 or stainless steel 1.4404 (316L) 3.00 mm**
Surface Electropolished stainless steel or painted sheet metal, RAL 7032
Gaskets Silicone (Lid and Gland Plates)
Lid fixing Fully detachable lid
Earthing Internal/external M10 earth stud
Enclosure mounting 4 external lugs with 11 mm slots
Equipment mounting 4 or 6 mounting pillars with M 6 threaded hole
Protection class IP 66, IP 67
Impact resistance 10 J
Temperature range –60 °C to +140 °C
Note: The horizontal spacing of the fixing lugs is reduced by 30 mm in the versions without gland plates on the sides (i.e. 0, 1 or 2 gland plate versions).
** 6 mm gland plates are available on request.
Ordering data – Sheet SteelDescription Dimensions 1 Gland Plate 2 Gland Plates 3 Gland Plates 4 Gland PlatesKlippon® TB10 229mm x 152mm x 133mm 0933000000 0933010000 0933020000 0933030000
Klippon® TB10A260mm x 260mm x 150mm 0934020000 0934030000 0934040000 0934050000260mm x 260mm x 200mm 0934080000 0934090000 0934100000 0934110000
Klippon® TB11306mm x 306mm x 150mm 0934140000 0934150000 0934160000 0934170000306mm x 306mm x 200mm 0934200000 0934210000 0934220000 0934230000
Klippon® TB11A350mm x 260mm x 150mm 0934260000 0934270000 0934280000 0934290000350mm x 260mm x 200mm 0934320000 0934330000 0934340000 0934350000
Klippon® TB11B450mm x 400mm x 150mm 0934380000 0934390000 0934400000 0934410000450mm x 400mm x 200mm 0934440000 0934450000 0934460000 0934470000
Klippon® TB12458mm x 382mm x 150mm 0904760000 0904770000 0904780000 0904790000458mm x 382mm x 200mm 0904840000 0904850000 0904860000 0904870000
Klippon® TB12A480mm x 480mm x 150mm 0904920000 0904930000 0904940000 0904950000480mm x 480mm x 200mm 0905000000 0905010000 0905020000 0905030000
Klippon® TB12B550mm x 350mm x 150mm 0905080000 0905090000 0905100000 0905110000550mm x 350mm x 200mm 0905160000 0905170000 0905180000 0905190000
Klippon® TB12C458mm x 300mm x 150mm 0905240000 0905250000 0905260000 0905270000458mm x 300mm x 200mm 0905320000 0905330000 0905340000 0905350000
Klippon® TB12D620mm x 450mm x 150mm 0942130000 0942140000 0942150000 0942160000620mm x 450mm x 200mm 0942180000 0942190000 0942200000 0942210000
Klippon® TB13762mm x 508mm x 150mm 0905400000 0905410000 0905420000 0905430000762mm x 508mm x 200mm 0905480000 0905490000 0905500000 0905510000
Klippon® TB14914mm x 610mm x 150mm 0905560000 0905570000 0905580000 0905590000914mm x 610mm x 200mm 0905640000 0905650000 0905660000 0905670000
15
Technical Overview
ApprovalsEmpty Enclosure (Component)ATEX marking: T II 2GD Ex e II Ex tD A21 IP66 & IP67 Baseefa06ATEX0010U
IECEx marking: Ex e II Ex tD A21 IP66 & IP67 IECEx BAS 06.0003U
Approved to IEC/EN 60079-0 and IEC/EN 60079-7 the latest harmonised standards for equipment used in hazardous areas.
Assembly: The New Klippon® TB range of enclosures can be assembled to customer requirements by Weidmüller to incorporate terminals / certified equipment.
Note: This is a component certified enclosure only, additional certification is required when assembled with other electrical equipment.
Terminal Enclosures(Equipment – Typical)
ATEX marking: T II 2GD Exe II Ex tD A21 T6 85°C / IP66 & IP67 Tamb -60°C to +40°C / Baseefa06ATEX0011X / MDP __ Amps __ Volts __ T II 2GD Exe ia II Ex tD A21 T6 85°C / IP66 & IP67 Tamb -60°C to +40°C / Baseefa06ATEX0011X* / MDP __ Amps __ Volts __
IECEx marking: Exe II Ex tD A21 T6 85°C / IP66 & IP67 Tamb -60°C to +40°C / IECEx BAS 06.0004X / MDP __ Amps __ Volts __ Exe ia II Ex tD A21 T6 85°C / IP66 & IP67 Tamb -60°C to +40°C / IECEx BAS 06.0004X / MDP __ Amps __ Volts __
Note: * For specific hazardous area requirements please contact Weidmüller for a copy of full certificate.
Ordering data – Stainless SteelDescription Dimensions 1 Gland Plate 2 Gland Plates 3 Gland Plates 4 Gland PlatesKlippon® TB10 229mm x 152mm x 133mm 0929000000 0929010000 0929020000 0929030000
Klippon® TB10A260mm x 260mm x 150mm 0929040000 0929050000 0929060000 0929070000260mm x 260mm x 200mm 0929080000 0929090000 0929100000 0929110000
Klippon® TB11306mm x 306mm x 150mm 0929120000 0929130000 0929140000 0929150000306mm x 306mm x 200mm 0929160000 0929170000 0929180000 0929190000
Klippon® TB11A350mm x 260mm x 150mm 0929200000 0929210000 0929220000 0929230000350mm x 260mm x 200mm 0929240000 0929250000 0929260000 0929270000
Klippon® TB11B450mm x 400mm x 150mm 0929280000 0929290000 0929300000 0929310000450mm x 400mm x 200mm 0929320000 0929330000 0929340000 0929350000
Klippon® TB12458mm x 382mm x 150mm 0904720000 0904730000 0904740000 0904750000458mm x 382mm x 200mm 0904800000 0904810000 0904820000 0904830000
Klippon® TB12A480mm x 480mm x 150mm 0904880000 0904890000 0904900000 0904910000480mm x 480mm x 200mm 0904960000 0904970000 0904980000 0904990000
Klippon® TB12B550mm x 350mm x 150mm 0905040000 0905050000 0905060000 0905070000550mm x 350mm x 200mm 0905120000 0905130000 0905140000 0905150000
Klippon® TB12C458mm x 300mm x 150mm 0905200000 0905210000 0905220000 0905230000458mm x 300mm x 200mm 0905280000 0905290000 0905300000 0905310000
Klippon® TB12D620mm x 450mm x 150mm 0942230000 0942240000 0942250000 0942260000620mm x 450mm x 200mm 0942280000 0942290000 0942300000 0942310000
Klippon® TB13762mm x 508mm x 150mm 0905360000 0905370000 0905380000 0905390000762mm x 508mm x 200mm 0905440000 0905450000 0905460000 0905470000
Klippon® TB14914mm x 610mm x 150mm 0905520000 0905530000 0905540000 0905550000914mm x 610mm x 200mm 0905600000 0905610000 0905620000 0905630000
16
Klippon® TB10 Bolt 133mm DeepSheet steel enclosures for use in industrial and hazardous area applications
Weight and Dimensions 1 Gland Plate 2 Gland Plates 3 Gland Plates 4 Gland Plates
Height x Width x Depth mm
229mm x 152mm x 133mm 3.5 kg 3.75 kg 4.25 kg 4.5 kg
Elevations
Ordering Data Enclosures Bolt Fastener VersionNumber of Gland Plates Part Number (133 Deep)
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
1 Gland Plate — Positioned on bottom (B) 0933000000 0929000000
2 Gland Plates — Positioned on top & bottom (A & B) 0933010000 0929010000
3 Gland Plates — Positioned on bottom, left & right (B, C & D) 0933020000 09290200004 Gland Plates — Positioned on top, bottom, left & right (A, B, C & D) 0933030000 0929030000
Number of Cable Entries A/B C/D(133 Deep) (133 Deep)
Max number of cable entries per enclosure side* M16 14 18
M20 5 7
M25 2 3
M32 2 2
M40 1 2
M50 0 0
M63 0 0
Max Number of Terminals (Industrial) W series H W series V Z series H Z series V SAK series H SAK series VWDU 2.5 ZDU 2.5 SAK 2.5 1 × 9 1 × 25 1 × 9 1 × 25 2 × 8 1 × 22
WDU 4 ZDU 4 SAK 4 1 × 8 1 × 21 1 × 8 1 × 22 3 × 7 1 × 20
WDU 6 ZDU 6 SAK 6 1 × 6 1 × 16 1 × 6 1 × 16 3 × 6 1 × 16
WDU 10 ZDU 10 SAK 10 1 × 4 1 × 13 1 × 4 1 × 13 3 × 4 1 × 13
WDU 16 ZDU 16 SAK 16 1 × 4 1 × 11 1 × 4 1 × 11 2 × 4 1 × 11
WDU 35 ZDU 35 SAK 35 1 × 3 1 × 8 1 × 3 1 × 8 1 × 2 1 × 7WDU 50N – – – – – –
Ordering Data AccessoriesSheet Steel Mounting Plate 1.5mm Painted RAL7032 Part NumberMounting Plate Sheet Steel painted RAL7032 0908480000
Stainless Sheet Steel Mounting Plate 1.4404 316L
Mounting Plate Sheel Steel 316L 0908470000
Stainless Steel Label Holder
Lid Label Holder S/S 0908760000
Padlock with key
Stainless Steel Padlock with 2 Keys (1 key fits all) 0905680000
Internal mounting spacers10mm Long 0935110000
15mm Long 0935120000
20mm Long 093513000030mm Long 0935140000
Comments * Cable entries based on Weidmüller´s standard IP68 cable glands – For specific hazardous area requirements please contact Weidmüller for a copy of the full certificate – General – 316L Stainless Steel enclosures are Electropolished for high performance under severe weather conditions
Technical Information
208 75
110
152
147
117
53
10565
M10 INTERNAL/EXTERNAL EARTH STUD M6 STANDOFF 15MM HIGH
4 PLACES
152
158
229
177
147
133
105
65
15
Ø 11
D
B
C
A
E
A = TopB = BottomC = LeftD = RightE = Base
A = TopB = BottomC = LeftD = RightE = Base
Note: For 1 gland plate and 2 gland plates versions subtract 30 mm from horizontal fixing centre dimensions
Front view Front view – door removed 133 Deep: View on right hand side and on bottom
Mounting Plate Mounting Plate dimensions
Padlock with key
91.00
75.00
158.00
174.00
17
Klippon® TB10A Bolt 150mm and 200mm DeepSheet steel enclosures for use in industrial and hazardous area applications
Weight and Dimensions 1 Gland Plate 2 Gland Plates 3 Gland Plates 4 Gland Plates
Height x Width x Depth mm
260mm x 260mm x 150mm 5.25 kg 6.0 kg 6.25 kg 7.0 kg
260mm x 260mm x 200mm 6.0 kg 7.0 kg 7.5 kg 8.25 kg
Elevations
Ordering Data Enclosures Bolt Fastener VersionNumber of Gland Plates Part Number (150 Deep) Part Number (200 Deep)
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
1 Gland Plate — Positioned on bottom (B) 0934020000 0929040000 0934080000 0929080000
2 Gland Plates — Positioned on top & bottom (A & B) 0934030000 0929050000 0934090000 0929090000
3 Gland Plates — Positioned on bottom, left & right (B, C & D) 0934040000 0929060000 0934100000 09291000004 Gland Plates — Positioned on top, bottom, left & right (A, B, C & D) 0934050000 0929070000 0934110000 0929110000
Number of Cable Entries A/B C/D A/B C/D(150 Deep) (150 Deep) (200 Deep) (200 Deep)
Max number of cable entries per enclosure side* M16 38 30 54 42
M20 12 10 22 16
M25 9 7 15 12
M32 4 3 8 6
M40 3 2 6 4
M50 2 2 2 2
M63 0 0 2 1M75 – – 1 1
Max Number of Terminals (Industrial) W series H W series V Z series H Z series V SAK series H SAK series VWDU 2.5 ZDU 2.5 SAK 2.5 2 × 30 2 × 31 2 × 30 2 × 31 2 × 26 2 × 27
WDU 4 ZDU 4 SAK 4 2 × 25 2 × 26 2 × 26 2 × 27 2 × 24 2 × 25
WDU 6 ZDU 6 SAK 6 2 × 19 2 × 20 2 × 19 2 × 20 2 × 19 2 × 20
WDU 10 ZDU 10 SAK 10 2 × 15 2 × 16 2 × 15 2 × 16 2 × 15 2 × 16
WDU 16 ZDU 16 SAK 16 2 × 13 2 × 13 2 × 13 2 × 13 2 × 13 2 × 13
WDU 35 ZDU 35 SAK 35 2 × 9 2 × 10 2 × 9 2 × 10 2 × 8 2 × 9WDU 50N 2 × 8 2 × 8 – – – –
Ordering Data AccessoriesSheet Steel Mounting Plate 1.5mm Painted RAL7032 Part NumberMounting Plate Sheet Steel painted RAL7032 0908500000
Stainless Sheet Steel Mounting Plate 1.4404 316L
Mounting Plate Sheel Steel 316L 0908490000
Stainless Steel Label Holder
Lid Label Holder S/S 0908760000
Padlock with key
Stainless Steel Padlock with 2 Keys (1 key fits all) 0905680000
Internal mounting spacers10mm Long 0935110000
15mm Long 0935120000
20mm Long 093513000030mm Long 0935140000
Comments * Cable entries based on Weidmüller´s standard IP68 cable glands – For specific hazardous area requirements please contact Weidmüller for a copy of the full certificate – General – 316L Stainless Steel enclosures are Electropolished for high performance under severe weather conditions
Technical Information
D
B
C
A
E
A = TopB = BottomC = LeftD = RightE = Base
A = TopB = BottomC = LeftD = RightE = Base
Note: For 1 gland plate and 2 gland plates versions subtract 30 mm from horizontal fixing centre dimensions
316 183
127
63
12282
260254224
170
189
260
150
122
82
260254214
200
172
13220
817
8
15
177
105
172132
260
208
168
15
Ø 11
M10 INTERNAL/EXTERNAL EARTH STUD
M6 STANDOFF 15MM HIGH4 PLACES
Front view Front view – door removed 150 Deep: View on right hand side and on bottom 200 Deep: View on right hand side and on bottom
Mounting Plate Mounting Plate dimensions
Padlock with key
199.00
183.00
189.00
205.00
18
Technical Information
Klippon® TB11 Bolt 150mm and 200mm DeepSheet steel enclosures for use in industrial and hazardous area applications
Weight and Dimensions 1 Gland Plate 2 Gland Plates 3 Gland Plates 4 Gland Plates
Height x Width x Depth mm
306mm x 306mm x 150mm 6.5 kg 7.25 kg 7.75 kg 8.5 kg
306mm x 306mm x 200mm 7.5 kg 8.5 kg 9.0 kg 10.0 kg
Elevations
Ordering Data Enclosures Bolt Fastener VersionNumber of Gland Plates Part Number (150 Deep) Part Number (200 Deep)
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
1 Gland Plate — Positioned on bottom (B) 0934140000 0929120000 0934200000 0929160000
2 Gland Plates — Positioned on top & bottom (A & B) 0934150000 0929130000 0934210000 0929170000
3 Gland Plates — Positioned on bottom, left & right (B, C & D) 0934160000 0929140000 0934220000 09291800004 Gland Plates — Positioned on top, bottom, left & right (A, B, C & D) 0934170000 0929150000 0934230000 0929190000
Number of Cable Entries A/B C/D A/B C/D(150 Deep) (150 Deep) (200 Deep) (200 Deep)
Max number of cable entries per enclosure side* M16 46 38 66 54
M20 14 12 28 22
M25 12 9 18 15
M32 5 4 8 8
M40 4 3 8 6
M50 3 2 3 2
M63 – – 2 2M75 – – 2 1
Max Number of Terminals (Industrial) W series H W series V Z series H Z series V SAK series H SAK series VWDU 2.5 ZDU 2.5 SAK 2.5 2 × 39 2 × 40 2 × 39 2 × 40 3 × 33 3 × 34
WDU 4 ZDU 4 SAK 4 2 × 33 2 × 34 2 × 33 2 × 34 3 × 31 3 × 32
WDU 6 ZDU 6 SAK 6 2 × 25 2 × 26 2 × 25 2 × 26 3 × 25 3 × 26
WDU 10 ZDU 10 SAK 10 2 × 20 2 × 21 2 × 20 2 × 21 3 × 20 3 × 20
WDU 16 ZDU 16 SAK 16 2 × 17 2 × 17 2 × 16 2 × 17 2 × 16 2 × 17
WDU 35 ZDU 35 SAK 35 2 × 12 2 × 13 2 × 12 2 × 13 2 × 11 2 × 11WDU 50N 2 × 10 2 × 11 – – – –
Ordering Data AccessoriesSheet Steel Mounting Plate 1.5mm Painted RAL7032 Part NumberMounting Plate Sheet Steel painted RAL7032 0908520000
Stainless Sheet Steel Mounting Plate 1.4404 316L
Mounting Plate Sheel Steel 316L 0908510000
Stainless Steel Label Holder
Lid Label Holder S/S 0908760000
Padlock with key
Stainless Steel Padlock with 2 Keys (1 key fits all) 0905680000
Internal mounting spacers10mm Long 0935110000
15mm Long 0935120000
20mm Long 093513000030mm Long 0935140000
Comments * Cable entries based on Weidmüller´s standard IP68 cable glands – For specific hazardous area requirements please contact Weidmüller for a copy of the full certificate – General – 316L Stainless Steel enclosures are Electropolished for high performance under severe weather conditions
361 229
127
64
122
82
306
301
271
203
235
306
150
122
82
306
301261
200
172
132
254
224
15
177
106
172132
306
254
214
15
Ø 11
M10 INTERNAL/EXTERNAL EARTH STUD
M6 STANDOFF 15MM HIGH4 PLACES
Mounting Plate dimensions
245.00
229.00
235.00
251.00
Front view Front view – door removed 150 Deep: View on right hand side and on bottom 200 Deep: View on right hand side and on bottom
Mounting Plate
Padlock with key
D
B
C
A
E
A = TopB = BottomC = LeftD = RightE = Base
A = TopB = BottomC = LeftD = RightE = Base
Note: For 1 gland plate and 2 gland plates versions subtract 30 mm from horizontal fixing centre dimensions
19
Technical Information
Klippon® TB11A Bolt 150mm and 200mm DeepSheet steel enclosures for use in industrial and hazardous area applications
Weight and Dimensions 1 Gland Plate 2 Gland Plates 3 Gland Plates 4 Gland Plates
Height x Width x Depth mm
350mm x 260mm x 150mm 6.2 kg 7.0 kg 7.8 kg 8.4 kg
350mm x 260mm x 200mm 7.25 kg 7.75 kg 9.0 kg 9.75 kg
Elevations
Ordering Data Enclosures Bolt Fastener VersionNumber of Gland Plates Part Number (150 Deep) Part Number (200 Deep)
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
1 Gland Plate — Positioned on bottom (B) 0934260000 0929200000 0934320000 0929240000
2 Gland Plates — Positioned on top & bottom (A & B) 0934270000 0929210000 0934330000 0929250000
3 Gland Plates — Positioned on bottom, left & right (B, C & D) 0934280000 0929220000 0934340000 09292600004 Gland Plates — Positioned on top, bottom, left & right (A, B, C & D) 0934290000 0929230000 0934350000 0929270000
Number of Cable Entries A/B C/D A/B C/D(150 Deep) (150 Deep) (200 Deep) (200 Deep)
Max number of cable entries per enclosure side* M16 38 46 54 66
M20 12 14 22 26
M25 9 11 15 18
M32 4 5 8 8
M40 3 4 6 8
M50 2 3 2 3
M63 – – 2 2M75 – – 1 2
Max Number of Terminals (Industrial) W series H W series V Z series H Z series V SAK series H SAK series VWDU 2.5 ZDU 2.5 SAK 2.5 3 × 30 2 × 49 3 × 30 2 × 49 4 × 26 2 × 42
WDU 4 ZDU 4 SAK 4 3 × 25 2 × 41 3 × 26 2 × 42 3 × 24 2 × 38
WDU 6 ZDU 6 SAK 6 3 × 19 2 × 32 3 × 19 2 × 31 3 × 19 2 × 31
WDU 10 ZDU 10 SAK 10 3 × 15 2 × 25 3 × 15 1 × 25 3 × 15 2 × 25
WDU 16 ZDU 16 SAK 16 3 × 13 2 × 21 3 × 13 1 × 21 3 × 13 2 × 21
WDU 35 ZDU 35 SAK 35 3 × 9 2 × 15 3 × 9 1 × 15 1 × 12 2 × 14WDU 50N 2 × 8 2 × 13 – – – –
Ordering Data AccessoriesSheet Steel Mounting Plate 1.5mm Painted RAL7032 Part NumberMounting Plate Sheet Steel painted RAL7032 0908540000
Stainless Sheet Steel Mounting Plate 1.4404 316L
Mounting Plate Sheel Steel 316L 0908530000
Stainless Steel Label Holder
Lid Label Holder S/S 0908760000
Padlock with key
Stainless Steel Padlock with 2 Keys (1 key fits all) 0905680000
Internal mounting spacers10mm Long 0935110000
15mm Long 0935120000
20mm Long 093513000030mm Long 0935140000
Comments * Cable entries based on Weidmüller´s standard IP68 cable glands – For specific hazardous area requirements please contact Weidmüller for a copy of the full certificate – General – 316L Stainless Steel enclosures are Electropolished for high performance under severe weather conditions
316183
127
64
122
82
260
254
224
250
279
320
150
122
82
260
254
214
200
172
132
298
268
15
177
106
172
132
350
298
258
15
Ø 11
M10 INTERNAL/EXTERNAL EARTH STUD
M6 STANDOFF 15MM HIGH4 PLACES
Mounting Plate dimensions
199.00
183.00
279.00
295.00
Front view Front view – door removed 150 Deep: View on right hand side and on bottom 200 Deep: View on right hand side and on bottom
Mounting Plate
Padlock with key
D
B
C
A
E
A = TopB = BottomC = LeftD = RightE = Base
A = TopB = BottomC = LeftD = RightE = Base
Note: For 1 gland plate and 2 gland plates versions subtract 30 mm from horizontal fixing centre dimensions
20
Technical Information
Klippon® TB11B Bolt 150mm and 200mm DeepSheet steel enclosures for use in industrial and hazardous area applications
Weight and Dimensions 1 Gland Plate 2 Gland Plates 3 Gland Plates 4 Gland Plates
Height x Width x Depth mm
450mm x 400mm x 150mm 10.0 kg 10.9 kg 11.8 kg 12.8 kg
450mm x 400mm x 200mm 11.25 kg 12.25 kg 13.5 kg 14.75 kg
Elevations
Ordering Data Enclosures Bolt Fastener VersionNumber of Gland Plates Part Number (150 Deep) Part Number (200 Deep)
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
1 Gland Plate — Positioned on bottom (B) 0934380000 0929280000 0934440000 0929320000
2 Gland Plates — Positioned on top & bottom (A & B) 0934390000 0929290000 0934450000 0929330000
3 Gland Plates — Positioned on bottom, left & right (B, C & D) 0934400000 0929300000 0934460000 09293400004 Gland Plates — Positioned on top, bottom, left & right (A, B, C & D) 0934410000 0929310000 0934470000 0929350000
Number of Cable Entries A/B C/D A/B C/D(150 Deep) (150 Deep) (200 Deep) (200 Deep)
Max number of cable entries per enclosure side* M16 64 64 96 96
M20 20 20 38 38
M25 16 16 24 24
M32 6 6 12 12
M40 5 5 10 10
M50 4 4 4 4
M63 – – 3 3M75 – – 3 3
Max Number of Terminals (Industrial) W series H W series V Z series H Z series V SAK series H SAK series VWDU 2.5 ZDU 2.5 SAK 2.5 4 × 58 3 × 69 4 × 58 3 × 69 5 × 49 4 × 58
WDU 4 ZDU 4 SAK 4 4 × 48 3 × 57 4 × 49 3 × 58 5 × 45 4 × 54
WDU 6 ZDU 6 SAK 6 4 × 37 3 × 44 4 × 37 3 × 44 5 × 37 4 × 44
WDU 10 ZDU 10 SAK 10 4 × 30 3 × 35 4 × 29 3 × 35 5 × 29 4 × 35
WDU 16 ZDU 16 SAK 16 4 × 24 3 × 29 4 × 24 3 × 29 4 × 24 4 × 29
WDU 35 ZDU 35 SAK 35 4 × 18 3 × 22 4 × 18 3 × 22 4 × 16 3 × 19WDU 50N 3 × 16 3 × 19 – – – –
Ordering Data AccessoriesSheet Steel Mounting Plate 1.5mm Painted RAL7032 Part NumberMounting Plate Sheet Steel painted RAL7032 0908560000
Stainless Sheet Steel Mounting Plate 1.4404 316L
Mounting Plate Sheel Steel 316L 0908550000
Stainless Steel Label Holder
Lid Label Holder S/S 0908760000
Padlock with key
Stainless Steel Padlock with 2 Keys (1 key fits all) 0905680000
Internal mounting spacers10mm Long 0935110000
15mm Long 0935120000
20mm Long 093513000030mm Long 0935140000
Comments * Cable entries based on Weidmüller´s standard IP68 cable glands – For specific hazardous area requirements please contact Weidmüller for a copy of the full certificate – General – 316L Stainless Steel enclosures are Electropolished for high performance under severe weather conditions
455 323
127
63
12282
40039536530
5 379
450
150
124
122
82
400395355
200
172
132
398
368
15
177
105
172132
450
398
368
15
Ø 11
M10 INTERNAL/EXTERNAL EARTH STUD
M6 STANDOFF 15MM HIGH4 PLACES
Mounting Plate dimensions
339.00
323.00
379.00
395.00
Front view Front view – door removed 150 Deep: View on right hand side and on bottom 200 Deep: View on right hand side and on bottom
Mounting Plate
Padlock with key
D
B
C
A
E
A = TopB = BottomC = LeftD = RightE = Base
A = TopB = BottomC = LeftD = RightE = Base
Note: For 1 gland plate and 2 gland plates versions subtract 30 mm from horizontal fixing centre dimensions
21
Technical Information
Klippon® TB12 Bolt 150mm and 200mm DeepSheet steel enclosures for use in industrial and hazardous area applications
Weight and Dimensions 1 Gland Plate 2 Gland Plates 3 Gland Plates 4 Gland Plates
Height x Width x Depth mm
458mm x 382mm x 150mm 9.8 kg 10.7 kg 11.7 kg 12.5 kg
458mm x 382mm x 200mm 11.0 kg 12.0 kg 13.5 kg 14.5 kg
Elevations
Ordering Data Enclosures Bolt Fastener VersionNumber of Gland Plates Part Number (150 Deep) Part Number (200 Deep)
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
1 Gland Plate — Positioned on bottom (B) 0904760000 0904720000 0904840000 0904800000
2 Gland Plates — Positioned on top & bottom (A & B) 0904770000 0904730000 0904850000 0904810000
3 Gland Plates — Positioned on bottom, left & right (B, C & D) 0904780000 0904740000 0904860000 09048200004 Gland Plates — Positioned on top, bottom, left & right (A, B, C & D) 0904790000 0904750000 0904870000 0904830000
Number of Cable Entries A/B C/D A/B C/D(150 Deep) (150 Deep) (200 Deep) (200 Deep)
Max number of cable entries per enclosure side* M16 60 66 90 96
M20 20 20 36 40
M25 15 17 24 24
M32 6 7 12 12
M40 5 5 10 10
M50 4 5 4 4
M63 – – 3 3M75 – – 3 3
Max Number of Terminals (Industrial) W series H W series V Z series H Z series V SAK series H SAK series VWDU 2.5 ZDU 2.5 SAK 2.5 4 × 54 3 × 70 4 × 54 3 × 70 5 × 46 4 × 60
WDU 4 ZDU 4 SAK 4 4 × 45 3 × 59 4 × 46 3 × 60 5 × 42 4 × 55
WDU 6 ZDU 6 SAK 6 4 × 35 3 × 45 4 × 34 3 × 45 5 × 34 4 × 45
WDU 10 ZDU 10 SAK 10 4 × 28 3 × 36 4 × 27 3 × 36 5 × 27 4 × 36
WDU 16 ZDU 16 SAK 16 4 × 23 3 × 30 4 × 23 3 × 30 4 × 23 3 × 30
WDU 35 ZDU 35 SAK 35 4 × 17 3 × 22 4 × 17 3 × 22 4 × 15 3 × 20WDU 50N 3 × 15 3 × 19 – – – –
Ordering Data AccessoriesSheet Steel Mounting Plate 1.5mm Painted RAL7032 Part NumberMounting Plate Sheet Steel painted RAL7032 0908580000
Stainless Sheet Steel Mounting Plate 1.4404 316L
Mounting Plate Sheel Steel 316L 0908570000
Stainless Steel Label Holder
Lid Label Holder S/S 0908760000
Padlock with key
Stainless Steel Padlock with 2 Keys (1 key fits all) 0905680000
Internal mounting spacers10mm Long 0935110000
15mm Long 0935120000
20mm Long 093513000030mm Long 0935140000
Comments * Cable entries based on Weidmüller´s standard IP68 cable glands – For specific hazardous area requirements please contact Weidmüller for a copy of the full certificate – General – 316L Stainless Steel enclosures are Electropolished for high performance under severe weather conditions
437 305
127
63
12282
382377347
305
387 458
150
122
82
382
377
337
200
172
132
406
376
15
177
105
172
132
458
406
366
15
Ø 11
M10 INTERNAL/EXTERNAL EARTH STUD
M6 STANDOFF 15MM HIGH4 PLACES
Mounting Plate dimensions
321.00
305.00
387.00403.00
Front view Front view – door removed 150 Deep: View on right hand side and on bottom 200 Deep: View on right hand side and on bottom
Mounting Plate
Padlock with key
D
B
C
A
E
A = TopB = BottomC = LeftD = RightE = Base
A = TopB = BottomC = LeftD = RightE = Base
Note: For 1 gland plate and 2 gland plates versions subtract 30 mm from horizontal fixing centre dimensions
22
Technical Information
Klippon® TB12A Bolt 150mm and 200mm DeepSheet steel enclosures for use in industrial and hazardous area applications
Weight and Dimensions 1 Gland Plate 2 Gland Plates 3 Gland Plates 4 Gland Plates
Height x Width x Depth mm
480mm x 480mm x 150mm 11.9 kg 13.0 kg 13.9 kg 14.9 kg
480mm x 480mm x 200mm 13.25 kg 14.75 kg 15.75 kg 17.25 kg
Elevations
Ordering Data Enclosures Bolt Fastener VersionNumber of Gland Plates Part Number (150 Deep) Part Number (200 Deep)
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
1 Gland Plate — Positioned on bottom (B) 0904920000 0904880000 0905000000 0904960000
2 Gland Plates — Positioned on top & bottom (A & B) 0904930000 0904890000 0905010000 0904970000
3 Gland Plates — Positioned on bottom, left & right (B, C & D) 0904940000 0904900000 0905020000 09049800004 Gland Plates — Positioned on top, bottom, left & right (A, B, C & D) 0904950000 0904910000 0905030000 0904990000
Number of Cable Entries A/B C/D A/B C/D(150 Deep) (150 Deep) (200 Deep) (200 Deep)
Max number of cable entries per enclosure side* M16 78 70 114 102
M20 24 22 48 42
M25 20 18 30 27
M32 8 7 16 14
M40 6 6 12 12
M50 5 5 5 5
M63 – – 4 4M75 – – 3 3
Max Number of Terminals (Industrial) W series H W series V Z series H Z series V SAK series H SAK series VWDU 2.5 ZDU 2.5 SAK 2.5 4 × 73 4 × 75 4 × 73 4 × 75 5 × 62 5 × 63
WDU 4 ZDU 4 SAK 4 4 × 61 4 × 62 4 × 62 4 × 63 5 × 58 5 × 58
WDU 6 ZDU 6 SAK 6 4 × 47 4 × 48 4 × 47 4 × 47 5 × 47 5 × 47
WDU 10 ZDU 10 SAK 10 4 × 38 4 × 38 4 × 37 4 × 38 5 × 37 5 × 38
WDU 16 ZDU 16 SAK 16 4 × 31 4 × 32 4 × 31 4 × 31 4 × 31 4 × 31
WDU 35 ZDU 35 SAK 35 4 × 23 4 × 23 4 × 23 4 × 23 4 × 20 4 × 21WDU 50N 4 × 20 4 × 20 – – – –
Ordering Data AccessoriesSheet Steel Mounting Plate 1.5mm Painted RAL7032 Part NumberMounting Plate Sheet Steel painted RAL7032 0908600000
Stainless Sheet Steel Mounting Plate 1.4404 316L
Mounting Plate Sheel Steel 316L 0908590000
Stainless Steel Label Holder
Lid Label Holder S/S 0908760000
Padlock with key
Stainless Steel Padlock with 2 Keys (1 key fits all) 0905680000
Internal mounting spacers10mm Long 0935110000
15mm Long 0935120000
20mm Long 093513000030mm Long 0935140000
Comments * Cable entries based on Weidmüller´s standard IP68 cable glands – For specific hazardous area requirements please contact Weidmüller for a copy of the full certificate – General – 316L Stainless Steel enclosures are Electropolished for high performance under severe weather conditions
535403
127
64
12282
480475445
327
409
480
150
122
82
480
475435
200
172
132
428
398
15
177
106
172132
480
428
399
15
Ø 11
M10 INTERNAL/EXTERNAL EARTH STUD
M6 STANDOFF 15MM HIGH4 PLACES
Mounting Plate dimensions
419.00
403.00
409.00
425.00
Front view Front view – door removed 150 Deep: View on right hand side and on bottom 200 Deep: View on right hand side and on bottom
Mounting Plate
Padlock with key
D
B
C
A
E
A = TopB = BottomC = LeftD = RightE = Base
A = TopB = BottomC = LeftD = RightE = Base
Note: For 1 gland plate and 2 gland plates versions subtract 30 mm from horizontal fixing centre dimensions
23
Technical Information
Klippon® TB12B Bolt 150mm and 200mm DeepSheet steel enclosures for use in industrial and hazardous area applications
Weight and Dimensions 1 Gland Plate 2 Gland Plates 3 Gland Plates 4 Gland Plates
Height x Width x Depth mm
550mm x 350mm x 150mm 10.5 kg 11.3 kg 12.8 kg 13.6 kg
550mm x 350mm x 200mm 11.75 kg 12.25 kg 14.75 kg 15.75 kg
Elevations
Ordering Data Enclosures Bolt Fastener VersionNumber of Gland Plates Part Number (150 Deep) Part Number (200 Deep)
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
1 Gland Plate — Positioned on bottom (B) 0905080000 0905040000 0905160000 0905120000
2 Gland Plates — Positioned on top & bottom (A & B) 0905090000 0905050000 0905170000 0905130000
3 Gland Plates — Positioned on bottom, left & right (B, C & D) 0905100000 0905060000 0905180000 09051400004 Gland Plates — Positioned on top, bottom, left & right (A, B, C & D) 0905110000 0905070000 0905190000 0905150000
Number of Cable Entries A/B C/D A/B C/D(150 Deep) (150 Deep) (200 Deep) (200 Deep)
Max number of cable entries per enclosure side* M16 54 82 78 120
M20 18 26 32 50
M25 14 21 21 33
M32 5 8 10 16
M40 4 7 8 14
M50 4 6 4 6
M63 – – 3 4M75 – – 2 4
Max Number of Terminals (Industrial) W series H W series V Z series H Z series V SAK series H SAK series VWDU 2.5 ZDU 2.5 SAK 2.5 5 × 48 3 × 88 5 × 48 3 × 88 6 × 41 4 × 75
WDU 4 ZDU 4 SAK 4 5 × 40 3 × 74 5 × 41 3 × 75 6 × 38 3 × 69
WDU 6 ZDU 6 SAK 6 5 × 31 3 × 57 5 × 30 3 × 56 6 × 30 3 × 56
WDU 10 ZDU 10 SAK 10 5 × 24 3 × 45 5 × 24 3 × 45 6 × 24 3 × 45
WDU 16 ZDU 16 SAK 16 5 × 20 3 × 38 5 × 20 3 × 37 5 × 20 3 × 37
WDU 35 ZDU 35 SAK 35 5 × 15 3 × 28 5 × 15 3 × 28 5 × 13 3 × 25WDU 50N 4 × 13 2 × 24 – – – –
Ordering Data AccessoriesSheet Steel Mounting Plate 1.5mm Painted RAL7032 Part NumberMounting Plate Sheet Steel painted RAL7032 0908620000
Stainless Sheet Steel Mounting Plate 1.4404 316L
Mounting Plate Sheel Steel 316L 0908610000
Stainless Steel Label Holder
Lid Label Holder S/S 0908760000
Padlock with key
Stainless Steel Padlock with 2 Keys (1 key fits all) 0905680000
Internal mounting spacers10mm Long 0935110000
15mm Long 0935120000
20mm Long 093513000030mm Long 0935140000
Comments * Cable entries based on Weidmüller´s standard IP68 cable glands – For specific hazardous area requirements please contact Weidmüller for a copy of the full certificate – General – 316L Stainless Steel enclosures are Electropolished for high performance under severe weather conditions
405 273
127
64
12282
350
345315
350 47
9
550
150
122
82
350345305
200
172
132
498
468
15
177
105
172132
550
498
458
15
Ø 11
M10 INTERNAL/EXTERNAL EARTH STUD
M6 STANDOFF 15MM HIGH6 PLACES
Mounting Plate dimensions
289.00273.00
239.50479.00
495.00
Front view Front view – door removed 150 Deep: View on right hand side and on bottom 200 Deep: View on right hand side and on bottom
Mounting Plate
Padlock with key
D
B
C
A
E
A = TopB = BottomC = LeftD = RightE = Base
A = TopB = BottomC = LeftD = RightE = Base
Note: For 1 gland plate and 2 gland plates versions subtract 30 mm from horizontal fixing centre dimensions
24
Technical Information
Klippon® TB12C Bolt 150mm and 200mm DeepSheet steel enclosures for use in industrial and hazardous area applications
Weight and Dimensions 1 Gland Plate 2 Gland Plates 3 Gland Plates 4 Gland Plates
Height x Width x Depth mm
458mm x 300mm x 150mm 8.3 kg 9.0 kg 10.1 kg 10.9 kg
458mm x 300mm x 200mm 9.25 kg 10.0 kg 11.75 kg 12.5 kg
Elevations
Ordering Data Enclosures Bolt Fastener VersionNumber of Gland Plates Part Number (150 Deep) Part Number (200 Deep)
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
1 Gland Plate — Positioned on bottom (B) 0905240000 0905200000 0905320000 0905280000
2 Gland Plates — Positioned on top & bottom (A & B) 0905250000 0905210000 0905330000 0905290000
3 Gland Plates — Positioned on bottom, left & right (B, C & D) 0905260000 0905220000 0905340000 09053000004 Gland Plates — Positioned on top, bottom, left & right (A, B, C & D) 0905270000 0905230000 0905350000 0905310000
Number of Cable Entries A/B C/D A/B C/D(150 Deep) (150 Deep) (200 Deep) (200 Deep)
Max number of cable entries per enclosure side* M16 46 64 66 96
M20 14 20 26 38
M25 11 16 18 24
M32 5 6 8 12
M40 4 5 8 10
M50 3 4 3 4
M63 – – 2 3M75 – – 2 3
Max Number of Terminals (Industrial) W series H W series V Z series H Z series V SAK series H SAK series VWDU 2.5 ZDU 2.5 SAK 2.5 4 × 38 2 × 70 4 × 38 2 × 70 5 × 32 3 × 60
WDU 4 ZDU 4 SAK 4 4 × 32 2 × 59 4 × 32 2 × 60 5 × 30 3 × 55
WDU 6 ZDU 6 SAK 6 4 × 24 2 × 45 4 × 24 2 × 45 5 × 24 3 × 45
WDU 10 ZDU 10 SAK 10 4 × 19 2 × 36 4 × 19 2 × 36 5 × 19 3 × 36
WDU 16 ZDU 16 SAK 16 4 × 16 2 × 30 4 × 16 2 × 30 4 × 16 2 × 30
WDU 35 ZDU 35 SAK 35 4 × 12 2 × 22 4 × 12 2 × 22 4 × 10 2 × 20WDU 50N 3 × 10 2 × 19 – – – –
Ordering Data AccessoriesSheet Steel Mounting Plate 1.5mm Painted RAL7032 Part NumberMounting Plate Sheet Steel painted RAL7032 0908640000
Stainless Sheet Steel Mounting Plate 1.4404 316L
Mounting Plate Sheel Steel 316L 0908630000
Stainless Steel Label Holder
Lid Label Holder S/S 0908760000
Padlock with key
Stainless Steel Padlock with 2 Keys (1 key fits all) 0905680000
Internal mounting spacers10mm Long 0935110000
15mm Long 0935120000
20mm Long 093513000030mm Long 0935140000
Comments * Cable entries based on Weidmüller´s standard IP68 cable glands – For specific hazardous area requirements please contact Weidmüller for a copy of the full certificate – General – 316L Stainless Steel enclosures are Electropolished for high performance under severe weather conditions
361 223
127
63
12282
300295265
305
387
458
150
122
82
300
295
255
200
172
132
398
368
15
177
105
172132
458
398
358
15
Ø 11
M10 INTERNAL/EXTERNAL EARTH STUD
M6 STANDOFF 15MM HIGH4 PLACES
Mounting Plate dimensions
239.00
223.00
387.00
403.00
Front view Front view – door removed 150 Deep: View on right hand side and on bottom 200 Deep: View on right hand side and on bottom
Mounting Plate
Padlock with key
D
B
C
A
E
A = TopB = BottomC = LeftD = RightE = Base
A = TopB = BottomC = LeftD = RightE = Base
Note: For 1 gland plate and 2 gland plates versions subtract 30 mm from horizontal fixing centre dimensions
25
Technical Information
Klippon® TB12D Bolt 150mm and 200mm DeepSheet steel enclosures for use in industrial and hazardous area applications
Weight and Dimensions 1 Gland Plate 2 Gland Plates 3 Gland Plates 4 Gland Plates
Height x Width x Depth mm
620mm x 450mm x 150mm 13.6 kg 14.7 kg 16.2 kg 17.2 kg
620mm x 450mm x 200mm 15.3 kg 16.6 kg 18.7 kg 20.0 kg
Elevations
Ordering Data Enclosures Bolt Fastener VersionNumber of Gland Plates Part Number (150 Deep) Part Number (200 Deep)
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
1 Gland Plate — Positioned on bottom (B) 0942130000 0942230000 0942180000 0942280000
2 Gland Plates — Positioned on top & bottom (A & B) 0942140000 0942240000 0942190000 0942290000
3 Gland Plates — Positioned on bottom, left & right (B, C & D) 0942150000 0942250000 0942200000 09423000004 Gland Plates — Positioned on top, bottom, left & right (A, B, C & D) 0942160000 0942260000 0942210000 0942310000
Number of Cable Entries A/B C/D A/B C/D(150 Deep) (150 Deep) (200 Deep) (200 Deep)
Max number of cable entries per enclosure side* M16 72 94 108 144
M20 22 30 44 58
M25 19 24 27 36
M32 7 10 14 18
M40 6 8 12 16
M50 5 7 5 7
M63 – – 4 5M75 – – 3 4
Max Number of Terminals (Industrial) W series H W series V Z series H Z series V SAK series H SAK series VWDU 2.5 ZDU 2.5 SAK 2.5 5 × 48 3 × 88 5 × 48 3 × 88 6 × 41 4 × 75
WDU 4 ZDU 4 SAK 4 5 × 40 3 × 74 5 × 41 3 × 75 6 × 38 3 × 69
WDU 6 ZDU 6 SAK 6 5 × 31 3 × 57 5 × 30 3 × 56 6 × 30 3 × 56
WDU 10 ZDU 10 SAK 10 5 × 24 3 × 45 5 × 24 3 × 45 6 × 24 3 × 45
WDU 16 ZDU 16 SAK 16 5 × 20 3 × 38 5 × 20 3 × 37 5 × 20 3 × 37
WDU 35 ZDU 35 SAK 35 5 × 15 3 × 28 5 × 15 3 × 28 5 × 13 3 × 25WDU 50N 4 × 13 2 × 24 – – – –
Ordering Data AccessoriesSheet Steel Mounting Plate 1.5mm Painted RAL7032 Part NumberMounting Plate Sheet Steel painted RAL7032 0942740000
Stainless Sheet Steel Mounting Plate 1.4404 316L
Mounting Plate Sheel Steel 316L 0942710000
Stainless Steel Label Holder
Lid Label Holder S/S 0908760000
Padlock with key
Stainless Steel Padlock with 2 Keys (1 key fits all) 0905680000
Internal mounting spacers10mm Long 0935110000
15mm Long 0935120000
20mm Long 093513000030mm Long 0935140000
Comments * Cable entries based on Weidmüller´s standard IP68 cable glands – For specific hazardous area requirements please contact Weidmüller for a copy of the full certificate – General – 316L Stainless Steel enclosures are Electropolished for high performance under severe weather conditions
M10 INTERNAL/EXTERNAL EARTH STUD
506450
150
12282
200
172132
450445405
450445405
106
373
450
549
620
568
528
620
568
528
150
122
82 200
15
63,5
15
172
132
620
Mounting Plate dimensions
321.00
305.00
387.00
403.00
Front view Front view – door removed 150 Deep: View on right hand side and on bottom 200 Deep: View on right hand side and on bottom
Mounting Plate
Padlock with key
D
B
C
A
E
A = TopB = BottomC = LeftD = RightE = Base
A = TopB = BottomC = LeftD = RightE = Base
Note: For 1 gland plate and 2 gland plates versions subtract 30 mm from horizontal fixing centre dimensions
26
Technical Information
Klippon® TB13 Bolt 150mm and 200mm DeepSheet steel enclosures for use in industrial and hazardous area applications
Weight and Dimensions 1 Gland Plate 2 Gland Plates 3 Gland Plates 4 Gland Plates
Height x Width x Depth mm
762mm x 508mm x 150mm 17.9 kg 18.6 kg 20.7 kg 21.8 kg
762mm x 508mm x 200mm 19.25 kg 20.0 kg 23.25 kg 24.75 kg
Elevations
Ordering Data Enclosures Bolt Fastener VersionNumber of Gland Plates Part Number (150 Deep) Part Number (200 Deep)
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
1 Gland Plate — Positioned on bottom (B) 0905400000 0905360000 0905480000 0905440000
2 Gland Plates — Positioned on top & bottom (A & B) 0905410000 0905370000 0905490000 0905450000
3 Gland Plates — Positioned on bottom, left & right (B, C & D) 0905420000 0905380000 0905500000 09054600004 Gland Plates — Positioned on top, bottom, left & right (A, B, C & D) 0905430000 0905390000 0905510000 0905470000
Number of Cable Entries A/B C/D A/B C/D(150 Deep) (150 Deep) (200 Deep) (200 Deep)
Max number of cable entries per enclosure side* M16 84 120 126 180
M20 26 38 50 74
M25 21 31 33 48
M32 8 12 16 24
M40 7 10 14 20
M50 6 9 6 8
M63 – – 5 7M75 – – 4 6
Max Number of Terminals (Industrial) W series H W series V Z series H Z series V SAK series H SAK series VWDU 2.5 ZDU 2.5 SAK 2.5 7 × 79 4 × 128 7 × 79 4 × 128 9 × 67 6 × 108
WDU 4 ZDU 4 SAK 4 7 × 66 4 × 107 7 × 67 4 × 108 9 × 62 5 × 100
WDU 6 ZDU 6 SAK 6 7 × 51 4 × 82 7 × 50 4 × 81 9 × 50 5 × 81
WDU 10 ZDU 10 SAK 10 7 × 40 4 × 66 7 × 40 4 × 65 9 × 40 5 × 65
WDU 16 ZDU 16 SAK 16 7 × 34 4 × 54 7 × 33 4 × 54 8 × 33 5 × 54
WDU 35 ZDU 35 SAK 35 7 × 25 4 × 40 7 × 25 4 × 40 7 × 22 4 × 36WDU 50N 6 × 21 4 × 35 – – – –
Ordering Data AccessoriesSheet Steel Mounting Plate 1.5mm Painted RAL7032 Part NumberMounting Plate Sheet Steel painted RAL7032 0908660000
Stainless Sheet Steel Mounting Plate 1.4404 316L
Mounting Plate Sheel Steel 316L 0908650000
Stainless Steel Label Holder
Lid Label Holder S/S 0908760000
Padlock with key
Stainless Steel Padlock with 2 Keys (1 key fits all) 0905680000
Internal mounting spacers10mm Long 0935110000
15mm Long 0935120000
20mm Long 093513000030mm Long 0935140000
Comments * Cable entries based on Weidmüller´s standard IP68 cable glands – For specific hazardous area requirements please contact Weidmüller for a copy of the full certificate – General – 316L Stainless Steel enclosures are Electropolished for high performance under severe weather conditions
564 431
127
64
12282
506
503473
508 67
9
762
150
122
82
508
503
463
200
172
132
710
680
15
177
106
172
132
762
710
670
15
Ø 11
M10 INTERNAL/EXTERNAL EARTH STUD
M6 STANDOFF 15MM HIGH8 PLACES
Mounting Plate dimensions
447.00431.00
215.50
679.40339.70
695.40
Front view Front view – door removed 150 Deep: View on right hand side and on bottom 200 Deep: View on right hand side and on bottom
Mounting Plate
Padlock with key
D
B
C
A
E
A = TopB = BottomC = LeftD = RightE = Base
A = TopB = BottomC = LeftD = RightE = Base
Note: For 1 gland plate and 2 gland plates versions subtract 30 mm from horizontal fixing centre dimensions
27
Technical Information
Klippon® TB14 Bolt 150mm and 200mm DeepSheet steel enclosures for use in industrial and hazardous area applications
Weight and Dimensions 1 Gland Plate 2 Gland Plates 3 Gland Plates 4 Gland Plates
Height x Width x Depth mm
914mm x 610mm x 150mm 23.1 kg 24.5 kg 26.9 kg 28.3 kg
914mm x 610mm x 200mm 25.25 kg 26.25 kg 30.0 kg 32.0 kg
Elevations
Ordering Data Enclosures Bolt Fastener VersionNumber of Gland Plates Part Number (150 Deep) Part Number (200 Deep)
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
Sheet Steel Painted RAL7032
Stainless Sheet Steel 1.4404 316L
1 Gland Plate — Positioned on bottom (B) 0905560000 0905520000 0905640000 0905600000
2 Gland Plates — Positioned on top & bottom (A & B) 0905570000 0905530000 0905650000 0905610000
3 Gland Plates — Positioned on bottom, left & right (B, C & D) 0905580000 0905540000 0905660000 09056200004 Gland Plates — Positioned on top, bottom, left & right (A, B, C & D) 0905590000 0905550000 0905670000 0905630000
Number of Cable Entries A/B C/D A/B C/D(150 Deep) (150 Deep) (200 Deep) (200 Deep)
Max number of cable entries per enclosure side* M16 102 148 150 222
M20 32 46 62 92
M25 26 39 39 57
M32 10 15 20 30
M40 9 13 16 24
M50 7 11 7 10
M63 – – 6 8M75 – – 5 7
Max Number of Terminals (Industrial) W series H W series V Z series H Z series V SAK series H SAK series VWDU 2.5 ZDU 2.5 SAK 2.5 8 × 99 5 × 157 8 × 99 5 × 157 11 × 84 7 × 134
WDU 4 ZDU 4 SAK 4 8 × 83 5 × 132 8 × 84 5 × 134 10 × 78 7 × 123
WDU 6 ZDU 6 SAK 6 8 × 64 5 × 101 8 × 63 5 × 100 10 × 63 7 × 100
WDU 10 ZDU 10 SAK 10 8 × 51 5 × 81 8 × 50 5 × 80 10 × 50 7 × 80
WDU 16 ZDU 16 SAK 16 8 × 42 5 × 67 8 × 42 5 × 67 9 × 42 6 × 67
WDU 35 ZDU 35 SAK 35 8 × 31 5 × 50 8 × 31 5 × 50 8 × 28 5 × 44WDU 50N 7 × 27 5 × 43 – – – –
Ordering Data AccessoriesSheet Steel Mounting Plate 1.5mm Painted RAL7032 Part NumberMounting Plate Sheet Steel painted RAL7032 0908680000
Stainless Sheet Steel Mounting Plate 1.4404 316L
Mounting Plate Sheel Steel 316L 0908670000
Stainless Steel Label Holder
Lid Label Holder S/S 0908760000
Padlock with key
Stainless Steel Padlock with 2 Keys (1 key fits all) 0905680000
Internal mounting spacers10mm Long 0935110000
15mm Long 0935120000
20mm Long 093513000030mm Long 0935140000
Comments * Cable entries based on Weidmüller´s standard IP68 cable glands – For specific hazardous area requirements please contact Weidmüller for a copy of the full certificate – General – 316L Stainless Steel enclosures are Electropolished for high performance under severe weather conditions
666 533
127
64
12282
610
605
575
559
831 914
150
122
82
610
605565
200
172
132
862
832
15
177
105
172132
914
862
822
15
Ø 11
M10 INTERNAL/EXTERNAL EARTH STUD
M6 STANDOFF 15MM HIGH8 PLACES
Mounting Plate dimensions
549.00533.00
415.70831.40
266.50
847.40
Front view Front view – door removed 150 Deep: View on right hand side and on bottom 200 Deep: View on right hand side and on bottom
Mounting Plate
Padlock with key
D
B
C
A
E
A = TopB = BottomC = LeftD = RightE = Base
A = TopB = BottomC = LeftD = RightE = Base
Note: For 1 gland plate and 2 gland plates versions subtract 30 mm from horizontal fixing centre dimensions
28
A solutions business that fits your business
We manage all projects from cradle to grave, so you are guaranteed a coherent and controlled approach to all projects and solutions. At the outset to all projects we start with intensive dialogue concerning the task in hand at this stage. We primarily offer detailed advice on:
• Choosing the best products• Recommending a suitable solution customised to your
requirements• Taking account of Industry specific requirements like: – Hazardous area certifications (e.g. ATEX, IEC Ex) – Global regional specifications – Ingress protection – Environmental conditions
Our vision is to understand your business needs which in turn will mean meeting and exceeding your expectations on all aspects of delivering our solutions offer.
Weidmüller Service
Customer solutions
29
Weidmüller Service
RailDesigner®
With our RailDesigner® software you are much more flexible: This design program enables you to configure individual enclosures by simply selecting the enclosure type from our standard range. You can add drill holes and adapt the enclosure to suit your needs. Furthermore you can incorporate it into your CAD program and create labels via an export interface with the Weidmüller M-Print® PRO software which can be printed out with our PrintJet.
On-line catalogue
If you are looking for detailed information on our whole assortment of enclosures or if you would like to search for all available accessories for our enclosures please go to: http://catalog.weidmueller.com
Customer support
30
Weidmüller Service
Customer specific assembly - capabilites
• Design engineering.• Complete assembly solutions.• Cable harnessing.• Full test facilities.• PCB design and manufacture.• Integrated solutions.• Inclusion of third party products.
As an external services provider, we can increase your capabilities with our range of services. We offer constantly high quality to the given standards. We have a wide range of expertise within the Weidmüller group. With extensive knowledge within many markets some areas we focus on are:
• The hazardous areas market – in particular oil and gas products.
• Transportation including over ground, under ground rolling stock and infrastructure.
• Power generation from diesel and gas generation to nuclear power.
• Commercial construction sector. • Caravans to super yachts.• Automative and machine tooling.
More than just services
At Weidmüller service & solution we aim to provide
• Highest quality• Within budget• On time • Right first time
Weidmüller bespoke solutions
• Vendor reduction• Increase capacity• Customer to focus on core competences• Reduced overhead recovery• Utilise human resources• Part no. / purchasing consolidation
31
Industry Segments
Oil, gas & petrochemical industry
Applications placed into a harsh or hazardous environments require an approval. Our Klippon® TB range of enclosures are certified to a variety of international standards including the latest European ATEX 94/9/EG and IEC-EX standards. These enclosures are typically used in instrumentation and control applications and are ideally suited to meet the demanding needs of the petrochemical industries.
Power industry
Designed to meet the quality and high standards demanded by the power industry (power generation and distribution). The enclosures are suitable for low voltage distribution, lighting and instrumentation applications.
Standard industrial application
Weidmüller Klippon® TB enclosures are also ideally suited for a variety of industrial applications where control, measurement or power connections are required. For demanding environments these enclosures offer a high ingress protection and an impact resistance of up to 10 Joules. The pad-lockable designed door offers both easy access and enhanced product security
Transportation
The demand for mobility in our society is growing constantly. Both our enclosures and our reliable connection technologies have long been supplied to the transportation industry. Suitable for use in applications such as shipping, rolling stock, commercial vehicles and trackside applications, including signaling systems within the transport networks of major cities around the world.
Industry Segments
32
AE UAE
United Arab Emirates Weidmuller Middle East FZE P.O. Box # 8591 SAIF-Zone Sharjah – VAE Phone +971 6 5572723 Fax +971 6 5572724 info@weidmueller.ae
AR Argentina
CPI SA Bauness 2660 1431 Buenos Aires Phone +54 11 45238008 Fax +54 11 45220546 compras@cpi.com.ar
AT Austria
Weidmüller Ges.m.b.H. Industriezentrum Nö Süd Straße 2, Objekt M2 2355 Wiener Neudorf Phone +43 2236 6708-0 Fax +43 2236 6708-199 office.at@weidmueller.com
AU Australia
Weidmüller Pty. Ltd. 43 Huntingwood Drive Huntingwood, NSW, 2148 P.O.Box 6944 Blacktown NSW, 2148 Phone +61 2 9671-9999 Fax +61 2 9671-9911 info@weidmuller.com.au www.weidmuller.com.au
AZ Azerbaijan
West Industries Ltd. Caspian Plaza, 5-th Floor 44 J. Jabbarly Str., Baku, Azerbaijan Phone +99412 499 15 15 Fax +99412 499 14 93 sales@west-i.com
BA Bosnia-Herzegovina
BH ES Elektrosistem d.o.o. ul. J. Veselinovica 18 78000 Banja Luka Bosna Phone +387 51 317500 Fax +387 51 317500 elsist@inecco.net www.elektrosistem.co.yu
BE Belgium
Weidmüller Benelux B.V. Mechelsesteenweg 519 bus 6 en 7 1930 Nossegem Phone +32 (0)2 752 40 70 Fax +32 (0)2 751 36 06 info@weidmueller.be
BG Bulgaria
Weid-Bul eOOd ul. Nezabravka 33 A, bl. 315/3/10 1113 Sofia Phone +359 2 9632560 Fax +359 2 9631098 weidbul@nat.bg
BH Bahrain
Khayber Trading Company P.O. Box 1976 Manama, Bahrain Phone +973 17720747 Fax +973 17720331 khayber@batelco.com.bh
BR Brazil
Conexel Conexoes Elétricas Ltda. Rua Garcia Lorca, 176- V. Paulicéia, 09695-900, Sao Bernado do Campo - SP, Brasil Phone +55 11 43669600 Fax +55 11 43621677 vendas@conexel.com.br www.conexel.com.br
BY Belarus
TECHNIKON Ltd. Oktyabrskaya Str. 16/5 Apt. 704 220030 Minsk Belarus Phone +375 17 2104626 Fax +375 17 2275830 technikon@belsonet.net
CA Canada
W Interconnections Canada Inc. 10 Spy Court, Markham, Ontario L3 R5 H6 Phone +1 905 475-1507 Fax +1 905 475-5855 info1@weidmuller.ca www.weidmuller.ca
CG Republic of Montenegro
Please contact ES-YU Elektrossistem, Republic of Serbia
CH Switzerland
Weidmüller Schweiz AG Rundbuckstrasse 2 8212 Neuhausen am Rheinfall Phone +41 52 6740707 Fax +41 52 6740708 info@weidmueller.ch www.weidmueller.ch
CL Chile
Felipe Bahamondes S.A./ATS AGRO Servicios Agroindustriales Maria Luisa Santander 0475 Providencia Casilla 3425 Santiago Phone +56 2 341-1271 Fax +56 2 341-1275 felipe@atsintech.com
CN China
Weidmüller Interface International Trading (Shanghai) Co., Ltd. 12 F, Century Ba-Shi Building, No. 398 Huaihai Road (M) Shanghai 200020 P.R. China Phone +86 21 63868188 Fax +86 21 63867177 www.cnweidmuller.com
CO Colombia
Automatizacion Avanzada S. A. Carrera 97 No. 42 A-23 B3, Santafe de Bogotá Colombia. Phone +57 1 4132048 Fax +57 1 4159788 mgallegos@ automatizacionavanzada.com
CR Costa Rica
ELVATRON S.A. 400 Norte Banco Costa Rica, la Uruca, San José, Costa Rica Phone +506 2 961060 Fax +506 2 960328 dirk.haase@elvatron.com
CS Republic of Serbia
ES-YU Elektrosistem Pariske komune 41 11070 Novi Beograd Serbien Phone +381 11 697212 Fax +381 11 693608 esyu@eunet.yu www.elektrosistem.co.yu
CZ Czech Republic
Weidmüller s. r. o. Videnska ul. 340 25242 Vestec u Prahy Phone +420 2 44001400 Fax +420 2 44001499 office@weidmueller.cz
DE Germany
Weidmüller GmbH & Co. KG Ohmstraße 9 32758 Detmold Phone +49 5231 1428-0 Fax +49 5231 1428-116 weidmueller@weidmueller.de www.weidmueller.de
DK Denmark
Knud Wexøe A/S Skaettekaeret 11 P.O. Box 152 2840 Holte Phone +45 45465800 Fax +45 45465801 wexoe@wexoe.dk
EC Ecuador
Elsystec S.A. Electricidad Sistemas y Tecnología Joaquin Tinajero E 3-25 y Jorge Drom Edificio Oquendo, Planta baja, Oficina 101 Quito, Ecuador Phone +593 2 2245 241 Fax +593 2 2456 755 Sales.est@uio.satnet.net
EE Estonia
Alter Electric OÜ Türi 6, 11313 Tallinn, Estonia Phone +372 65 19 666 Fax +372 65 19667 alter@alter.ee
EG Egypt
Standard Electric 87, Mohamed Farid Street Heliopolis, Cairo, Egypt Phone +20 6 42 29 77/ 6 42 29 88 Fax +20 6 42 29 55 stdelec@rite.com
ES Spain
Weidmüller S. A. Narcis Monturiol 11-13 Pol.Ind. Sudoeste 08960 Sant Just Desvern Barcelona Phone +34 93 4803386 Fax +34 93 3718055 weidmuller@weidmuller.es www.weidmuller.es
FI Finland
JUHA-ELEKTRO OY Kylvöpolku 6, P. O. Box 57 00681 Helsinki Phone +358 10 8328 100 Fax +358 10 8328 169
FR France
Weidmüller EURL 12, Chaussée Jules César B.P. 263 Osny 95523 CERGY PONTOISE Cedex Phone +33 1 34245500 Fax +33 1 34245501 mail@weidmuller.fr www.weidmueller.com
GB United Kingdom
Weidmuller Ltd. 1 Abbey Wood Road Kings Hill, West Malling Kent ME19 4YT Phone +44 1732 877000 Fax +44 1732 873873 info@weidmuller.co.uk www.weidmueller.com
GR Greece
Electrorama S.A. 1 An. Martali Str. 41335 Larissa Phone +30 2410 552533 Fax +30 2410 283463 valvizos@electrorama.com.gr
HK Hong Kong
United Equity Limited Suite B, 11/F International Industrial Centre 2-8 Kwei Tei Street, Fotan, Shatin Hong Kong Phone +852 26876739 Fax +852 26876735 united_equity@sinatown.com
HR Croatia
Elektro Partner d.o.o. Radnicka cesta 22 10000 Zagreb Phone +385 1 6184793 Fax +385 1 6184795 elektropartner@zg.htnet.hr
HU Hungary
Weidmüller Kereskedelmi Kft Mádi u. 50 1104 Budapest P. O. Box 22 1507 Budapest Phone +36 1 464-7888 Fax +36 1 3827701 info@weidmueller.hu
ID Indonesia
P. T. Nego Electrindo Komplek Sentra Kramat, Blok A18 Jl. Kramat Raya No. 7-9 Jakarta 10450 Indonesia Phone +62 21 315 6218 Fax +62 21 315 6219 sutrisno@negoelectrindo.co.id
IE Ireland
A.P. Haslam Ltd. 14 Sunshine Ind. Estate Crumlin Road Dublin 12 Phone +353 1 453-2522 Fax +353 1 453-2949 paul.haslam@aphaslam.ie
IL Israel
A.U. Shay Ltd. Embar Street 23/25 P.O.Box 10049 Petach-Tikva 49222 Phone +972 3 9233601 Fax +972 3 9234601 shay@uriel-shay.com
IL Israel
ATEKA Ltd. 23 Hayetzira St. Kiryat Aryeh 49130 Petach-Tikva, Israel Phone +972 3 9392344 Fax +972 3 9243273 marketing@ateka.co.il www.ateka.co.il
IN India
Weidmüller Representative office Vijay Dattani # 156-4th cross, Prashant Extension Whitefield Bangalore - 560 066 Phone +91 80 8453999 vdattani@eth.net
IR Iran
TAF Co. 72, Iranshahr Av. Unit 5, 15816 Teheran Phone +98 21 8831-7851 Fax +98 21 8882-0268 info@taf-co.com
IS Iceland
Samey Automation Center Lyngas 13, 210 Garoabaer, Iceland Phone +354 510 5200 Fax +354 510 5201 samey@samey.is
IT Italy
Weidmüller S.r.l. Via Albert Einstein 4 20092 Cinisello Balsamo Milano Phone +39 02 660681 Fax +39 02 6124945 weidmuller@weidmuller.it www.weidmuller.it
JO Jordan
Trans Jordan for Electro Mechanic Supplies PLC. P.O.Box: 330607 Amman 11133, Jordan Phone +962 6 533 2020 Fax +962 6 533 5800 transjordan@batelco.jo
JP Japan
Nihon Weidmüller Co. Ltd. Asahi Seimei Bldg. 11F 1-14-1 Fuchucho Fuchu-shi Tokyo 183-0055 Japan Phone +81 42 330-7891 Fax +81 42 330-7895 www.weidmuller.co.jp
KR South Korea
Weidmüller Co., Ltd. 6floor, Seahwa building, 242-54 Nonhyun-dong, Kangnam-Gu Seoul Korea, Zip: 135-830 Phone +82 2 5160003 Fax +82 2 5160090 info@weidmuller.co.kr
Worldwide activities
33
KW Kuwait
KANA CONTROLS General Trading & Cont. CO. W.L.L. Al Rai Industrial Area, Plot 28-30, St. 31, Kuwait P.O.Box: 25593 Safat, 13116 Kuwait Phone +965-474 1373/4 Fax +965-474 1537 info@kanacontrols.com
KZ Kazakhstan
SEA STAR INTERNATIONAL. L.L.P. 42-A, Suite-15, Dostyk Ave Almaty - 050010 Republic of Kazakhstan Phone +7 3272 2 662502 / 938842 /
910580 / 911193 Fax +7 3272 2 501780
sales@seastargroup.com www.seastar.kz
LB Lebanon
Progress Engineering & Trading Enterprises P.O. Box 11-1111 Pharaon Bldg., Opp Electr. du Liban Chafaca Str., Al Nahr Beirut - Lebanon Phone +961 1 444664 Fax +961 1 561880 progress@inco.com.lb
LT Lithuania
ELEKTROS IRANGA Tinklu g.29a, 5319 Panevezys, Lithuania Phone +370 45582828 Fax +370 45582727 info@eliranga.lt
LU Luxembourg
Weidmüller Benelux B.V. Phone +352 24 527145 Fax +352 24 527147 info@weidmueller.lu
LV Latvia
PROFS Latvija SIA K. Ulmana gatve 140 LV-1029 Riga Latvia Phone +371 7870557 Fax +371 7870541 edgars.vilkins@profs.lv www.profs.lv
MD Moldova
BERHORD A&D srl 44, srt. Sarmizegetusa 37/3 Off 414. b-dul Decebal, 3, MD2001 Chisinau, Republic of Moldova Phone +373 22 507137 Fax +373 22 507134 atiuleanu@berhord.com
MK Macedonia
ELEKTRO – SMK dooel UL. III Makedonska brigada b.b. 1000 Skopje Macedonia Phone +389 22 460 295 Fax +389 22 460 298 Elektro-smk@telekabel.net.mk
MT Malta
E.S.S. Electrical Supplies & Services Ltd 104 J. Sciberras Str. Hamrun Malta HMR 08 Phone +356 21 255 777 Fax +356 21 255 999 robert@ess.com.mt
MX Mexico
W Interconnections, S.A. de C.V. Blvd. Hermanos Serdán No. 698 Col. San Rafael Oriente Puebla, Pue. C.P. 72029 Phone +52 222 2686266 to 68 ext.101 Fax +52 222 2686219 clientes@weidmuller.com.mx www.weidmuller.com.mx
MY Malaysia
Connect Plus Technology Sdn Bhd 9, Jalan PJS 11/24, Bandar Sunway, 46150 Petaling Jaya, Selangor Darul Ehsan, Malaysia Phone +60 3 5633 7363 Fax +60 3 5633 6562 andy@cptech.com.my www.cptech.com.my
NL Netherlands
Weidmüller Benelux B.V. Franciscusweg 221 1216 SE Hilversum Postbus 1505 1200 BM Hilversum Phone +31 35 6261261 Fax +31 35 6234569 info@weidmuller.nl www.weidmuller.nl
NO Norway
Siv. Ing. J. F. Knudtzen A/S Billingstadsletta 97 1396 Billingstad, P.O. Box 160 1378 Nesbru Phone +47 66 983350 Fax +47 66 980955 patorgersbraaten@jfknudtzen.no
NZ New Zealand
Cuthbert S. Steward Limited 27 Te Puni Street POB 38496 Petone Petone, Wellington Phone +64 4 5686156 Fax +64 4 5686056
OM Oman
DAN INTERNATIONAL LLC. PO.BOX 2901 111 Seeb Oman Phone +968 503 677 Fax +968 503 755 yedu@danintl.com
PE Peru
TECNOLOGÍA ELÉCTRICA Y SOLUCIONES S.A.C. Calle Huandoy 501, Lima 32 – Perú Phone +51 1 5620004 Fax +51 1 5620004 info@tecsol-peru.com
PH Philippines
El Criscent Corporation B-41 L-10, Villa Palao, Banlic, Calamba City Laguna 4027, Philippines Phone +63 49 345 6329 Fax +63 49 345 6329 ecc@laguna.net
PH Philippines
Enclosure Systems Specialists Inc G/F, GE Building 2291 Don Chino Roces Ava Ext Makati City 1231, Philippines Phone +63 2 813 8580 Fax +63 2 813 8596 encsys@mozcom.com
PL Poland
Weidmüller Sp. z o.o. ul. Goledzinowska 10 03-302 Warszawa Poland Phone +48 22 5100940 Fax +48 22 5100941 biuro@weidmuller.com.pl www.weidmuller.pl
PT Portugal
Weidmüller - Sistemas de Interface, S. A. Estrada Outeiro Polima, Lote B, N° B2, Escritório 2 - Abóboda 2785-518 Sao Domingos de Rana Lisboa Phone +351 21 4459190 Fax +351 21 4455871 weidmuller@weidmuller.pt www.weidmuller.pt
PY
Paraguay Please contact CPI S.A., Buenos Aires, Argentina
QA Qatar
Doha Motors (Technical Division) Post Box No. 145 Al Wakrath Road Doha-Qatar Phone +974 465 1441 Fax +974 465 4579 dmtctech@qatar.net.qa
RO Romania
Rominterface Impex SRL Str. Gh. Dem Teodorescu 30A 030916 Bukarest - sector 3 Phone +40 21 3220230 Fax +40 21 3228857 office@rominterface.ro
RU Russia
Weidmüller Representative Office Shabolovka street 2 119049 Moskau, Russia Phone +7 095 771-6940 Fax +7 095 771-6941 info@weidmueller.ru www.weidmueller.ru
SA Saudi Arabia
Saudi Electric Supply Co. P.O. Box 3298, Al Khobar 31952 Saudi Arabien Phone +966 3 882-9546227 Fax +966 3 882-9547 customer.service@sesco-ge.com
SA Saudi Arabia
Al Abdulkarim Holding Co. P. O. Box 4 Dammam 31411 Saudi Arabien Phone +966 3 833 7110 Fax + 966 3 833 8242 akte@akte.com.sa
SE Sweden
Weidmüller AB Axel Danielssons väg 271 P.O. box 31025 200 49 Malmö Phone +46 (0) 7 71 43 00 44 Fax +46 (0) 40 37 48 60 www.weidmuller.se info@weidmuller.se
SG Singapore
Weidmüller Pte. Ltd 70 Bendemeer Road #04–03 Luzerne Singapore 339940 Phone +65 6841 5311 Fax +65 6841 5377 info@weidmuller.com.sg www.weidmuller.com.sg
SI Slovenia
ELEKTROSPOJI d.o.o. Stegne 25 1000 Ljubljana Phone +38 6 15113810 Fax +38 6 15111604 elektrospoji@siol.net
SK Slovakia
Elektris s.r.o. Racianska 188 SK 83153 Bratislava, Slovakia Phone +421 2 49200113 Fax +421 2 44680328 weidmueller@computel.sk
SY Syria
Please contact Weidmüller Middle-East United Arab Emirates
TH Thailand
Pisanu Engineering Co., Ltd. 800/2 Asoke Dindaeng Road, Dindaeng, Bangkok 10400, Thailand Phone +66 2 2459113 Fax +66 2 2463214 ecsales@pisanu.co.th www.pisanu.co.th
TR Turkey
Weidmüller Elektronik Ticaret Ltd. Sti. Kavacik Mah. Mihrabad Cad. 143/1 34810 Beykoz –
.Istanbul / Turkey
Phone +90 216 5371070 (Pbx) Fax +90 216 5371077 info@weidmuller.com.tr
TW Taiwan
Fittatek Co., Ltd. 12F No. 185 Fu-Kuo Road, Tso Ying Dist Kaohsiung, Taiwan Phone +886 7 556 0858 Fax +886 7 556 3279 stanley@fittatek.com.tw
TW Taiwan
Eucan Enterprise Ltd. No. 145 He Ping 2nd Rd Kaohsiung, Taiwan Phone +886 7 715 6610 Fax +886 7 715 8748 mark@eucan.com.tw www.eucan.com.tw
UA Ukraine
TEKO INTERFACE ooo ul. Lewanewskogo 6 03058 Kiew Phone +38 044 401 09 90/91/92 Fax +38 044 401 08 64 weidmueller@tekointerface.com www.tekointerface.com.ua
US USA
W-Interconnections, Inc. 821 Southlake Boulevard, Richmond, VA 23236 Phone +1 804 7942877 Fax +1 804 3792593 info@weidmuller.com www.weidmuller.com
UY Uruguay
Rewo Uruguay S.A. AV. Bolivia 2001 Esq Rocafuerte Carrasco Montevideo Phone +598 260 4 8439 Fax +598 260 4 8439 clorda@rewouruguay.com.uy
VE Venezuela
Somerinca C. A. Edificio Esteban Piso 2 Calle Vargas Bolleita Notre Caracas 1070 A Venezuela Phone +58 212 2352748 Fax +58 212 2385625 klocmoeller@cantv.net
VN Vietnam
New Sky Co., Ltd 206 Nguyen Thai Binh Str., Ward 12., Tan Binh Dist., Ho Chin Minh City Vietnam Phone +848 811 6768 Fax +848 811 7899 newsky-e@hcm.vnn.vn www.newsky-e.com
YE Yemen
Please contact Weidmüller Middle-East United Arab Emirates
ZA South Africa
Phambili Interface (Pty.) Ltd. 5 Bundo Road Sebenza Extension Edenvale 1609 P.O.Box 193 Edenvale 1610 Phone +27 11 452-1930 Fax +27 11 452-6455 alockyer@radinterface.co.za
DE Other countries
Weidmüller Interface GmbH & Co. KG Postfach 3030 32720 Detmold Klingenbergstraße 16 32758 Detmold Phone +49 5231 14-0 Fax +49 5231 14-20 83 info@weidmueller.com www.weidmueller.com
Group companies
Agency abroad
Without own Agency
DE
DE
DE
34
We cannot guarantee that there are no mistakes in the publications or software provided by us to the customer for the purpose of making orders. We try our best to quickly correct errors in our printed media. For this purpose we list corrections, which have been identified after publishing printed media, on our web site at www.weidmueller.com. For convenience we list these corrections against product catalogue number and/or page number. This Internet-database is part of our catalogue.
All orders are based on our general terms of delivery, which can be reviewed on the websites of our group companies where you place your order. On demand we can also send the general terms of delivery to you.
Order number:5661080000/12/2007/SMMD
United Kingdom Weidmüller Ltd.1 Abbey Wood Road, Kings Hill,West Malling, Kent, ME19 4YT.Sales +44 (0) 845 094 2006Technical +44 (0) 845 094 2007www.weidmueller.com
USA W-Interconnections, Inc.821 Southlake Boulevard,Richmond, VA 23236.Sales +1 840 794 2877Fax +1 840 379 2593www.weidmueller.com
Other CountriesWeidmüller Interface GmbH & Co. KGP.O. Box 303032720 Detmold.Sales +49 5231 14 0Fax +49 5231 14 20 83www.weidmueller.com
www.weidmueller.com
ArgentinaAustraliaAustriaAzerbaijan BahrainBelarusBelgiumBosnia-HerzegovinaBrazilBulgariaCanadaChileChinaColombiaCosta RicaCroatiaCzech RepublicDenmarkEcuadorEgyptEstoniaFinlandFranceGermanyGreeceHong KongHungaryIcelandIndiaIndonesia
IranIrelandIsraelItalyJapanJordanKazakhstanKuwaitLatviaLebanonLithuaniaLuxembourgMacedoniaMalaysiaMaltaMexicoMoldovaMontenegroNetherlandsNew ZealandNorwayOmanParaguayPeruPhilippinesPolandPortugalQatarRomaniaRussiaSaudi Arabia
SerbiaSingaporeSlovakiaSloveniaSouth AfricaSouth KoreaSpainSwedenSwitzerlandSyriaTaiwanThailandTurkeyUAEUkraineUnited KingdomUruguay USAVenezuelaVietnamYemen
Weidmüller is the leading provider of solutions for electrical connectivity, transmission and conditioning of power, signals and data in industrial environments.The company develops, produces and sells products in the field of electrical connectivity, functional and communication electronics. For OEM suppliers the company sets international standards in engineering, procurement, manufacturing and distribution of customized solutions.
top related