vertex tube and fabrication
Post on 13-Jan-2017
111 Views
Preview:
TRANSCRIPT
APROJECT
PRESENATETION ON
FABRICATION OF VORTEX TUBE
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
AProject
Presentation on“Design and fabrication of vortex tube”
Presented by Shah Mohd AsifUjjawal SinghSubhadeep De
Santosh PalUnder the guidancePro. Nitin Galwade
Mechanical department
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
CONTENTS
•INTRODUCTION•CONSTRUCTION•WORKING•EXPRIMENTAL SETUP•VORTEX TUBE ASSEMBLY•EXPECTED OUT COME•FACILITIES RQUIRED•ADVANTAGE•APPLICATION•CONCLUSION
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
INTRODUCTIONA vortex tube is device without moving the mechanical parts which converts the gas flow in initially homogeneous in temperature, in to separate flow of different temperatures. This device was described by Ranque (1933) and examined experimentally in the 1940’s by Hilsch (1940). The vortex tube requires no work or heat.
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
CONSTRUCTION
Pressure gaugeSpinnerHot pipeCold pipeThermo meterMagnetic stand
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
PRESSURE GAUGE
The function of pressure gauge in vortex tube to the measured inlet pressure of air.
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
SPINNER
The function of the spinner is to convert the normal flow of the air to the radial flow.
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
FORNT SIDE
It is used for flow the hot pressurized air. It is manufactured of Brass.
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
Hot pipe:
Cold pipe:Cold pipe is a flexible pipe in which cold pressurized air flows. It is manufactured of fiber
HOT PIPE
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
COLD PIPE
Thermometer is a device it to be measured temperature.in vortex tube, it is used to measure the temperature of hot and cold air.
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
Thermometer
Digital thermometer
MAGNETIC STAND
Basically, magnetic stand is used to hold the vortex tube and a magnet is fixed on the base of the stand with a
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
WORKINGCompressed air is passed through the nozzle, vortex flow is created in the chamber and air travels in spiral like motion along the periphery of the hot side. , air stream through the core gets cooled below the inlet temperature of the air in the vortex tube, while air stream in forward direction get s heated up. The cold stream is escaped through the diaphragm hole into the cold side,
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
while hot stream is passed through the opening of the valve. By controlling the opening of the valve, the quantity of the cold air and its temperature can be varied.
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
EXPERIMENTAL SETUP
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
Experimental setup consist of compressor vortex tube and temperature indicator. The inlet pressure is measured using the pressure gauge. the temperature of the at cold end, at hot end and ambient air are measured using thermocouple.
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
VORTEX TUBE ASSEMBLY
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
EXPECTED OUTCOMES
Digital flow signal Wire rangibility
No zero drift Low pressure drop
Pulse outcome for totalizing Liquid stream or
gas Applications
Low installed cost
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
FACILITIES REQUIRED
Proper Vortex Sizing Process conditions Piping requirements Full pipe Good alignment of piping Concentric Reducers if required THEEM COLLEGE OF ENGINEERING
Guide Pro. NITIN GALWADE
ADVANTAGES OF VORTEX TUBE•No moving parts, maintenance free, high reliability •Output easily controlled •Constant temperature •No electricity or RF interference •Intrinsically safe •No refrigerant or chemicals •Effective spot cooling •Low cost •Compact, lightweight
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
APPLICATION
1)Vortex tubes are extremely small and as it produce hot as well as cold air. It may be of use in industries where both are simultaneously required. 2) Temperature as low as –500C can be obtained without any difficulty, so it is very much useful in industries for spot cooling of electronic components. 3) It is commonly used for body cooling of the workers in mines.4) Grinding operation
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
CONCLUSIONA simple model of the vortex tube is described that captures the physics related to one possible operating mechanism. The model is shown to faithfully reproduce a limited set of data if two empirical parameters are adjusted. The semi-empirical model is subsequently used to evaluate the potential performance benefit associated with replacing the throttling valve in a refrigeration system with an appropriately optimized vortex tube.
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
THANK YOU!
THEEM COLLEGE OF ENGINEERINGGuide Pro. NITIN GALWADE
top related