unit heater kbp · ... kbp-rt provision for remote thermostat (line voltage) n/a n/a ......
Post on 26-Apr-2018
227 Views
Preview:
TRANSCRIPT
Charley’s Home Page Charley’s Bubble Insulation
Charley’s Greenhouses Greenhouse Building Supplies
Greenhouse Supplies See All Heaters
10-13 #C4017 Super Heater
(800) 322-4707
SERIES
www.king-electric.com
King Electrical Manufacturing Company / 9131 10th Avenue South, Seattle, WA 98108 / phone 206.762.0400 / fax 206.763.7738
unit heaterPIC-A-WATT® / MULTI-PURPOSE / 950 or 6000 WATTS / CEILINGS UNDER 10 FT
KBP
FEATURES:
Pic-A-Watt® Element Cast Iron Motor Aluminum Fan Blade Built-in Thermostat Quiet Running
•Multiplewattageselection•Powder-coatedfinish•Standardcolor:almond•Universalmountingbracket•Fandelay•Selectorswitch- Fan / Heat / Off•TestedunderUL1278•Bi-metallic limit turns elementoffifanovertemperatureconditionoccursthenautomaticallyresetswhennormaltemperaturereturns
ENGINEERING SPECIFICATIONS:
The KBP is an excellent choice for a garage or shop heater withthecapacitytoeasilyheatalargespace.Theflow-throughdesignmovesairefficientlybypullingairfromthebackoftheheateranddischargingitoutthefront.
This rugged heater has qualitycomponentssuitableforcommercialapplicationsaswell.Itcomesstandardwitha3-positionswitchandanaccuratebuilt-inthermostat listing degrees on thelabelforprecisetemperaturecontrol.Anincludedfandelayhelpsdissipateheatfromtheelements.
Thisheatercanbepurchasedwithoptional(-K1)(120Volt)or(-K2)(240Volt)accessorykits.
Tested under UL1278
ContractorshallsupplyandinstallKBPSeriesunitheatersmanufacturedbyKingElectricalMfg.Company.Heaters shall beof thewattageandvoltageasindicatedontheplans.
Pic-A-Watt® Heating Element: Exclusive Kingmulti-tap elementallowsfieldadjustmenttoseveralwattagesattimeofinstallation.Steelsheathelementsofvariousresistancearecopperbrazedtosteelplatefinsproducingamulti-wattageheatingelement.
Built-in Thermostat:SinglePolefactoryinstalledhydrauliccapillarytube thermostatwith precision heating control.Operating range40ºto90ºF.
Fan / Heat / Off Switch: 3-position switch provides heating andsummerfanonlyoperation.TheDPSToffswitchprovidesa“positiveoff”thatdisconnectsallungroundedconductors.Notavailablein480Vand3-Phasemodels.
Fan Delay Switch:Thefancontinuestooperateafterthethermostatshutsoff inordertoremovetheresidualheatleft intheelements.Powermustnotbeinterrupted.
Universal Mounting Bracket:Combinationceiling/wall/floorbracketisincludedwitheveryheater.
Unit Bearing Motor: Permanentlylubricated,castiron,4-Polemotorwith20ccofoil.Enclosedrotorprovideslong-lasting,trouble-freeoperation.Thermallyprotected.1300RPM.
Auto-Reset Thermal Limit Control:Heatershutsoffwhenanovertemperatureconditionsexistandautomaticallyresetswhenthenormaloperatingtemperaturereturns.
Exterior: Texturedacrylicpowder-coatingprovidesanattractivedurablefinishinalmondcolor.
Approval:cCSAus(LR43323)
•30Ampplug,cord,handlekit•Remotethermostat(-RT)•24Voltcontrol(-RTLV)
OPTIONS:
LR43323
Hobby Greenhouse Kits Propagation Supplies Greenhouse Gardening Tips
Garden Supplies Portable Greenhouses Sign up for our Gardening Email
10-13
www.king-electric.com
King Electrical Manufacturing Company / 9131 10th Avenue South, Seattle, WA 98108 / phone 206.762.0400 / fax 206.763.7738
SELECTION:
ACCESSORIES:
DIMENSIONS:
StandardColor:TexturedAlmond
MODEL CODE:
Series
Volts
Watts
1or3Phase
RemoteT-Stat
24VRemoteT-Stat
KBP2006-3MP-RT-RTLV
KBP
208
5700
3MP
RT
RTLV
30Amp120VoltN.E.M.A.#5-30PModelKBP-K1
30Amp250VoltN.E.M.A.#6-30PModelKBP-K2
Receptacleconfigurationsincludedforcordset
380V-3ØHeatersareavailableinmostkWratings
*Approvedfor208Voperation.Heaterwilldraw13%lessAmpsand25%lesswattage**3-PhaseunitsdonothaveHeat/Fan/Off***480Voltmodelsare24Voltcontrol
MODELUPC
#093319PART #
VOLTS PHASE WATTAGE RANGEPHASE AMPS
SINGLE / THREE
MOTOR SIZE CFM TEMP RISE
(°F) AIR THROW WT.(lbs.)
KBP1230 15191 120 1 2850•1900•950 24 5W 270 35° 16ft. 26
KBP2406 15190 240* 15700•4750•
38002850•1900•950
24 5W 270 70° 16ft. 24
KBP2006-3MP** 15193 208 1-3 5700•2850 27/16 5W 270 70° 16ft. 26
KBP2406-3MP** 15188 240* 1-3 5700•2850 24/14 5W 270 70° 16ft. 25
KBP2704 15187 277 14000•30002000•1000
15 5W 270 47° 16ft. 26
KBP4804-3MP** 15196 480*** 1-3 4160 9 / 5 5W 270 49° 16ft. 26
KBP4806-3MP** 15197 480*** 1-3 6000 13/8 5W 270 71° 16ft. 26
*Factoryinstalledonly-Heat/Fan/Offactivatedatunitonly-cannotoperateremotely
MODEL DESCRIPTIONUPC
#093319PART #
WT. (lbs.)
KBP-K16ft.Cord/HandleKit-120V,1-Phase,30Amp
(receptacleincluded)15198 2
KBP-K26ft.Cord/HandleKit-240V,1-Phase,30Amp
(receptacleincluded)15199 2
KBP-RT ProvisionforRemoteThermostat(linevoltage) N/A N/A
*KBP-RTLV1 ProvisionforRemoteThermostat–1-Phase(24V) N/A N/A
*KBP-RTLV3 ProvisionforRemoteThermostat–3-Phase(24V) N/A N/A
INSTALLATION WIRING FOR REMOTE THERMOSTAT
Powermustberoutedtoheaterfirst,thentoremotethermostat.Thisisduetothefandelaycircuitneededtocooltheelementsonshutdown.
Bracketsideandbottomview
2MOUNTINGSTYLESMulti-positionalbracketallowsunlimitedmountingoptions
13½"Hx10"Wx11½"D
111/16"
25/16"
113/16"
23/8"
¾"knockout ½"knockout
FRONT BACK
INSTALLATION & MAINTENANCE MANUAL
WARNINGModel: KBP2406 is 240 volt. It is important that you verify the power supply voltage is the same as the nameplate voltage of the heater. Improper installation or failure to follow the procedures as outlined in this manual can result in damage to the heater. Note that the KBP2406 will operate at 208 volt but will produce 25% less wattage and draw 13% less Amps. Discon-nect all power from the heater at the main service panel before attempting to install or service this unit. All electrical wiring must conform to local electrical codes. Heater circuit must be properly protected.Unpack & Inspect Your New Heater
Remove heater from box and inspect it for any damage. Verify you have received the mounting bracket and accessories.
Tools NeededYou will need the following tools to install your unit heater: -Screwdriver - (Phillips & Slotted) -Wire Cutters -Pliers -Adjustable Wrench -Electric Drill
Hardware NeededYou will need the following hardware: -Adequate gauge & length of wire for your application -Proper size fuses or breakers to handle amperage -Proper wire connectors for your application -Appropriate size fasteners to mount heater.
In certain applications conduit may be required by code. Check local electrical codes. If you want to be able to turn the heater be sure to use flexible conduit.
Mounting HeightWhen the air flow of the heater is directed vertically or horizontally the minimum mounting height is 6 feet in USA and 8 feet in Canada. Mounting heights depend upon building utilization and heater kW capacity.
Distance From WallsMaintain 6" minimum clearance to side walls and 2" to ceiling in back of the heater (air intake side). Maintain 18" clearance in front of the heater (discharge side).
Mounting Heater Locate a stud in ceiling or wall and securely fasten bracket with a minimum of two #12 fasteners 1-1/4" long. Attach heater to bracket with 3/8" x 1" wingnut & lock washer supplied. Install the lock washer between the bracket and heater. Do not put lock washer on the plastic wingnut. After desired air discharge position has been determined tighten wingnut so heater will not pivot.
Location of HeaterThe heater should be installed out-of-reach of persons. The direction of airflow should not be restricted by machinery, beams, etc. and the airflow should wipe exposed walls, rather than blowing directly at them. When more than one heater is used in an area the heaters should be arranged so that the air discharge of each heater supports the airflow of the others to provide best circulation of warm air. (see airflow chart)
Model: KBP2406 240V-1phase Unit Heater
2007KBP2406.indd : 3/08
INSTALLATION INSTRUCTIONSSAVE THESE INSTRUCTIONS
OWNERS GUIDE & INSTALLATION INSTRUCTIONS SHOULD BE LEFT WITH HEATER FOR HOME OWNER
KING ELECTRICAL MFG. COMPANY • 9131 10th Ave So. • Seattle, WA 98108 • Ph: 206.762.0400 • Fax: 206.763.7738 • www.king-electric.com
21¾"
13"
½"
This heater includes a visual alarm to warn that parts of the heater are getting excessively hot. If the alarm flashes immediately turn the heater off and inspect for any objects on or adjacent to the heater that may cause high temperatures. Do not operate the heater with the alarm flashing.
1250 • 1500 • 1750 • 2000 • 2500 • 2750WATTAGES AVAILABLE IN ONE UNIT
INSTALLATION INSTRUCTIONSThis heater is shipped from the factory wired for maximum wattage of 2750 Watts at 120 Volts. To reduce the watt-age unplug (disconnect) an insulated push on terminal and wrap with electri-cal tape to prevent the possibility of electrical contact with other parts.
Feild Wattage Selection A - ORANGE Disconnects 750 Watts B - BLUE Disconnects 500 Watts C - YELLOW Disconnects 250 WattsD - BLACK Do Not Disconnect (Common)E - RED Do Not Disconnect
Insulated Push on Terminal
A
BLUE
750 WATT
250 WATT
RED
YELLOW C
B
E
ORANGE
RED E
BLA
CK
#14
END VIEW OF ELEMENTSHOWING QUICK CONNECT TERMINALS
A E
D Common
750
E
E C
D Common
750
B
500
250 500
500 WATT
500 WATT
LIMIT
RE
D #
14
BLACK #16
1 2 3 4
L2
BLA
CK
ORANGE #14
Insulated Push on Terminal
OFF ....... L1-0, L2-0FAN ....... L1-2, L2-4HEAT...... L1-1, L2-4, L2-3
750 WATT
Rotary Switch
L1
L1 L2
VISUALALARM
D
D
LPW1227
Pic-A-WattMetal Sheath Element
FAN DELAY1-3 N.C. , 1-2 N.C.1-2 Closes on Temp Rise
LPW1227.indd : 4/08
Safety Light
BLACK#16
ORANGE#14GRAY #16
PURPLE #16
ThermostatConnections
FAN2
3
1
FANDELAY
ORANGE#14
top related