unified-pcmc ver. 7 tda100d ver. 5.1 support tde/ncp ver. 4.2 support 2010/dec/27 2nd version

Unified-PCMCVer. 7

TDA100D ver. 5.1 supportTDE/NCP ver. 4.2 support

2010/Dec/27 2nd version

UPCMC v7 series

Each version supports the following.

V7.0 : KX-TDA100D v5.1 support.V7.1 : KX-TDE100/200/600, KX-NCP500/1000 v4.2 support. KX-TDA50(USA) v6.0 support.

Table of improvements

No. Contents Page

1 Slot structure 8

2 Four DPT interface ports (DLC4) on MPR 9

3 MCSLC24 and MCSLC16 Card 10

4 CLCOT8/16 Card 11

5 Removal of MEC card 12

6 FAX Transfer 13

7 Quick Setup Improvement 14

8 Function supported by other model 15

9 Dealer Control 18

Changes according to TDA100D v5.1 specification

No. Contents Page

1 Connect update 22

1. TDA100D is added 22

2 New update 23

1. TDA100D is added 23

3 PBX Replacement update 24

1. TDA100D V5.1 is supported 24

2. TDE/NCP V4.2 is supported 28

Common tool specification changing

No. Contents Page

1 Change Suffix code description 30

2 Access control to TDA100D 33

Installer update

Improvement Details

Changes according to TDA100D v5.1 specification

7th slot is added to the slot structure of current TDA100. 7th slot is added to the slot structure of current TDA100. 11stst - 7th slots are used as free slot. - 7th slots are used as free slot.

Slot structure (1/1)

DLC ports(DLC4) are mounted on MPR.The slot number of MPR is "11” (fixed).DPT ： T7600/DT300/VM/DPT-CS/HD-CS can connect to DLC4.The extension number is always assigned from the extension of DLC4.

Four DPT interface ports (DLC4) on MPR (1/1)

Caller ID(FSK only) is supported in new MCSLC24 and MCSLC16. (Do not support the Caller ID for DTMF type)Message Wait that is equivalent of MSLC16.PFT (Two Power Failure Transfer) is available.

MCSLC24 and MCSLC26 Card (1/1)

16ports is available with CLCOT8E card.Caller ID of FSK/DTMF/FSK with Visual CIT type are available.PFT (Two Power Failure Transfer) is available.Pay Tone service is not available.Installation CLCOT8E Card can be checked by Card Property.

CLCOT8/16 Card (1/1)

[2.6.2 Quick Dial]

[Personal Speed Dialing No.] of [4.1.3 Speed Dial]

[6.1 System Speed Dial]

[6.2 Hotel & Charge]

Removal of MEC card (1/1)

MEC 1-100 Expand 1-100

Expansion tab is always displayed

Personal Speed Dial is always displayed.

Expanded memory for Tenant is always displayed.

Billing for Guest (Need MEC card)

Billing for Guest

Add the FAX Transfer feature.Add [Fax Extension] in [5.3.2 DISA Message].

This function is supported in TDA30, NCP series, and TDE series.

Specifies the extension number to which to transfer a call when the MSG card detects a fax signal.

FAX Transfer (1/1)

Improve Quick Setup

Add CO Dialing Mode selection

The user can select Extension and ICD Group Number from pull down list.

Quick Setup Improvement (1/1)

The range is 0,10000-65535.

The CTI Port Number range in CTILINK Card is changed.

Function supported by other model (1/3)

"24 Ports Analogue Extension Card HOOK Threshold setting" is supported

Function supported by other model (2/3)

- The password cannot be seen from PCMC. - The password cannot be seen from PCMC. (same as NCP/TDE)(same as NCP/TDE)

- The function to prevent login when you incorrectly input the - The function to prevent login when you incorrectly input the password three times was added. password three times was added. At that time the Error Message(E030113) is displayed.At that time the Error Message(E030113) is displayed.

Error Message(E030113)You have reached the maximum number of login attempt. Please login in after a while again.

Improved password protection

Function supported by other model (3/3)

TDA100D PCMC refuses connection to ‘other area’ model.

Dealer control (1/3)

PCMC BXTDA100D RU, CN

Connection Refused !

(Different suffix of PBX)

TDA100D RU/UC, CNTDA100D RU/UC, CN

- If Registration Key is not input, you can not use some functions. - If Registration Key is not input, you can not use some functions.

When you access the following When you access the following menus, this error ismenus, this error is displayed. displayed.

- Port Property of PRI30- Port Property of PRI30- [1.2 Portable Station]- [1.2 Portable Station]- [9.1 TIE Table]- [9.1 TIE Table]

Dealer control (2/3)

You can input the You can input the Registration Key from this.Registration Key from this.

TDA100D RU/UCTDA100D RU/UC

-You can also input the Registration Key at You can also input the Registration Key at -““Tool(T) - License Registration(L)”.Tool(T) - License Registration(L)”.

Dealer control (3/3)TDA100D RU/UCTDA100D RU/UC

Common tool specification changes.

Connect update (1/1)1. TDA100D is added

New update (1/1)1. TDA100D is added

Note;- If a card is installed inSlot8,Slot9,Slot10 or Slot11, PBX Replacement can not run. It is necessary to delete these cards.

- If DHLC8 or SLC8 is installed, PBX Replacement can not run. It is necessary to delete these cards.

- If MSLC16,SLC16 or CSLC16 are installed, they are converted to MCSLC16 automatically.

Support TDA100/200(v5.0) -> TDA100D(v5.1) replacement

PBX Replacement update (1/5)1. TDA100D V5.1 is supported

- TDA100D -> TDA100/200/600 is not supported. - TDA100D -> TDE100/200/600 is not supported.

(1) When you convert the system data of TDA100/200 from versions other than Version 5.

-> You cannot convert the system data and the following error message is displayed.

You have to convert to V.5 before converting to TDA100D .

PBX Replacement update (2/5)

(1) When you convert the system data of TDA100/200 which includes DHLC cards and/or SLC cards.

-> You cannot convert the system data and the following error message is displayed.

You have to remove these cards.

PBX Replacement update (3/5)

(1) When you convert the system data of TDA200 with cards assigned to Slots 8~11.

-> You cannot convert the system data and the following error message is displayed.

You have to remove the cards in Slots 8~11.

PBX Replacement update (4/5)

PBX Replacement update (5/5)2. TDE/NCP V4.2 is supported

DSYS Converter

UPCMC TDE/NCP

DSYS Converter output

V7.0 v4.x

V7.1 v4.x

PBX Replacement

UPCMC TDA100/200

　 TDE100/200

TDE100/200

　 TDE600

TDA600

　 TDE600

V7.0 v5.0 v4.x v3.0 v4.x v5.0 v4.x

V7.1 v5.0 v4.x v3.0 v4.x v5.0 v4.x

Note: Because v4.x has common system data format, the output file of DSYS Converter is same between UPCMC v7.0 and v7.1.

Note: Because v4.x has common system data format, the output file of the above PBX Replacement is same between UPCMC v7.0 and v7.1.

Installer Update

Change Suffix code description (1/3)Installer of UPCMC V7 (Suffix)

New design for supporting KX-TDA100D.

Change Suffix code description (2/3)Installer of UPCMC V7 (Area selection for NE)

Change Suffix code description (3/3)Installer of UPCMC V7 (Area selection for CE)

Access control to TDA100D

UPCMC Suffix. Area

NE All area

CE All area

GR

E/UK

HK(TDE600XE/TDA100DXE)

SN(TDE600XE/TDA100DXE)

TW(TDE600XE/TDA100DXE)

BX/SU/BA

You can access the contents of KX-TDA100D only when you select the correct suffix when installing the UPCMC.

Thank You Very MuchFor Your Attention

“ We are Panasonic Family”