toshiba-mw20fp1c_tv+vcr+dvd video player sm

SERVICE MANUAL

COLOR TELEVISION/VIDEO CASSETTE RECORDER/DVD VIDEO PLAYER

MW20FP1C

FILE NO. 140-200417

PREPARATION OF SERVICING

The laser diode used for a pickup head may be destroyed with external static electricity.Moreover, even if it is operating normally after repair, when static electricity discharge is received at thetime of repair, a life of product may become short.Please perform the following measure against static electricity, be careful of destruction of a laser diodeenough at the time of repair, and work.

• It works on the desk which performed measures against static electricity, such as conductive mat.• Soldering iron with ground wire or ceramic type is used.• A worker needs to use a ground conductive wrist strap for body.

Location of the required MarkingThe rating sheet and the safety caution are on the rear of the unit.

CERTIFICATION: COMPLIES WITH FDARADIATION PERFORMANCE STANDARDS,21 CFR SUBCHAPTER J.

CAUTION

THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.

TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS SERVICE MANUAL CARE-FULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE,CONTACT AN AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE.

USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THANTHOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE.VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED. DO NOTSTARE INTO BEAM.

SERVICING NOTICES ON CHECKING

6. AVOID AN X-RAY1. KEEP THE NOTICESAs for the places which need special attentions,they are indicated with the labels or seals on thecabinet, chassis and parts. Make sure to keep theindications and notices in the operation manual.

3. USE THE DESIGNATED PARTS

5. TAKE CARE TO DEAL WITH THECATHODE-RAY TUBE

In the condition that an explosion-proof cathode-ray tube is set in this equipment, safety issecured against implosion. However, whenremoving it or serving from backward, it isdangerous to give a shock. Take enough care todeal with it.

Safety is secured against an X-ray by consider-ing about the cathode-ray tube and the highvoltage peripheral circuit, etc.Therefore, when repairing the high voltage pe-ripheral circuit, use the designated parts andmake sure not modify the circuit.Repairing except indicates causes rising of highvoltage, and it emits an X-ray from the cathode-ray tube.

Please include the following informations when you order parts. (Particularly the VERSION LETTER.)1. MODEL NUMBER and VERSION LETTER

The MODEL NUMBER can be found on the back of each product and the VERSION LETTER can be found at the end of the SERIAL NUMBER.2. PART NO. and DESCRIPTION

You can find it in your SERVICE MANUAL.

HOW TO ORDER PARTS

PERFORM A SAFETY CHECK AFTERSERVICING

Confirm that the screws, parts and wiring whichwere removed in order to service are put in theoriginal positions, or whether there are theportions which are deteriorated around theserviced places serviced or not. Check theinsulation between the antenna terminal orexternal metal and the AC cord plug blades.And be sure the safety of that.

(INSULATION CHECK PROCEDURE)

Unplug the plug from the AC outlet.Remove the antenna terminal on TV and turnon the TV.Insulation resistance between the cord plugterminals and the eternal exposure metal[Note 2] should be more than 1M ohm byusing the 500V insulation resistance meter[Note 1].If the insulation resistance is less than 1Mohm, the inspection repair should berequired.

[Note 1]

If you have not the 500V insulationresistance meter, use a Tester.

[Note 2]External exposure metal: Antenna terminal

2. AVOID AN ELECTRIC SHOCKThere is a high voltage part inside. Avoid anelectric shock while the electric current isflowing.

The parts in this equipment have the specificcharacters of incombustibility and withstandvoltage for safety. Therefore, the part which isreplaced should be used the part which hasthe same character.Especially as to the important parts for safetywhich is indicated in the circuit diagram or thetable of parts as a mark, the designatedparts must be used.

4. PUT PARTS AND WIRES IN THEORIGINAL POSITION AFTERASSEMBLING OR WIRINGThere are parts which use the insulationmaterial such as a tube or tape for safety, orwhich are assembled in the condition thatthese do not contact with the printed board.The inside wiring is designed not to get closerto the pyrogenic parts and high voltage parts.Therefore, put these parts in the originalpositions.

IMPORTANT SAFEGUARDS1.

READ INSTRUCTIONSAll the safety and operating instructions should be read before the unit is operated.RETAIN INSTRUCTIONSThe safety and operating instructions should be retained for future reference.HEED WARNINGSAll warnings on the unit and in the operating instructions should be adhered to.FOLLOW INSTRUCTIONSAll operating and use instructions should be followed.CLEANINGUnplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a dampcloth for cleaning.ATTACHMENTSDo not use attachments not recommended by the unit’s manufacturer as they may cause hazards.WATER AND MOISTUREDo not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, or laundry tub, in a wetbasement, or near a swimming pool.ACCESSORIESDo not place this unit on an unstable cart, stand, tripod, bracket, or table. The unit may fall, causing serious injury, and serious damage to the unit. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer.An appliance and cart combination should be moved with care. Quick stops,excessive force, and uneven surfaces may cause the appliance and cartcombination to overturn.VENTILATIONSlots and openings in the cabinet and in the back or bottom are provided for ventilation, to ensure reliableoperation of the unit, and to protect it from overheating. These openings must not be blocked or covered. Theopenings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unitshould never be placed near or over a radiator or heat source. This unit should not be placed in a built-ininstallation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructionshave been adhered to.POWER SOURCESThis unit should be operated only from the type of power source indicated on the rating plate. If you are not sureof the type of power supply to your home, consult your appliance dealer or local power company. For unitsintended to operate from battery power, or other sources, refer to the operating instructions.GROUNDING OR POLARIZATIONThis unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other).This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plugfully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace yourobsolete outlet. Do not defeat the safety purpose of the polarized plug. If your unit is equipped with a 3-wiregrounding-type plug, a plug having a third (grounding) pin, this plug will only fit into a grounding-type poweroutlet. This too, is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician toreplace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.POWER-CORD PROTECTIONPower-supply cords should be routed so that they are not likely to be walked on or pinched by items placed uponor against them, paying particular attention to cords at plugs, convenience receptacles, and the point where theyexit from the appliance.LIGHTNINGTo protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unitdue to lightning and power line surges.POWER LINESAn outside antenna system should not be located in the vicinity of overhead power lines or other electric light orpower circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system,extreme care should be taken to keep from touching such power lines or circuits, as contact with them might befatal.OVERLOADINGDo not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.OBJECT AND LIQUID ENTRYDo not push objects through any openings in this unit, as they may touch dangerous voltage points or short outparts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.

PORTABLE CART WARNING(symbol provided by RETAC)

S3125A

IMPORTANT SAFEGUARDS (CONTINUED)

OUTDOOR ANTENNA GROUNDINGIf an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is groundedso as to provide some protection against voltage surges and built-up static charges. Section 810 of the NationalElectrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and support-ing structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location ofantenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.SERVICINGDo not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltageor other hazards. Refer all servicing to qualified service personnel.DAMAGE REQUIRING SERVICEUnplug this unit from the wall outlet and refer servicing to qualified service personnel under the followingconditions:

REPLACEMENT PARTSWhen replacement parts are required, be sure the service technician uses replacement parts specified by themanufacturer or those that have the same characteristics as the original parts.Unauthorized substitutions may result in fire, electric shock or other hazards.SAFETY CHECKUpon completion of any service or repairs to this unit, ask the service technician to perform safety checks todetermine that the unit is in proper operating condition.WALL OR CEILING MOUNTINGThe product should be mounted to a wall or ceiling only as recommended by the manufacturer.HEATThe product should be situated away from heat sources such as radiators, heat registers, stoves, or otherproducts (including amplifiers) that produce heat.DISC TRAYKeep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.CONNECTINGWhen you connect the product to other equipment, turn off the power and unplug all of the equipment from thewall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's manual ofthe other equipment carefully and follow the instructions when making any connections.SOUND VOLUMEReduce the volume to the minimum level before you turn on the product. Otherwise, sudden high volume soundmay cause hearing or speaker damage.SOUND DISTORTIONDo not allow the product output distorted sound for a longtime. It may cause speaker overheating and fire.HEADPHONESWhen you use the headphones, keep the volume at a moderate level. If you use the headphones continuouslywith high volume sound, it may cause hearing damage.LASER BEAMDo not look into the opening of the disc tray or ventilation opening of the product to see the source of the laserbeam. It may cause sight damage.DISCDo not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personalinjury and product malfunction.NOTE TO CATV SYSTEM INSTALLERThis reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that providesguidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to thegrounding system of the building, as close to the point of cable entry as practical.

a.b.c.d.

When the power-supply cord or plug is damaged.If liquid has been spilled, or objects have fallen into the unit.If the unit has been exposed to rain or water.If the unit does not operate normally by following the operating instructions. Adjust only those controls thatare covered by the operating instructions, as an improper adjustment of other controls may result indamage and will often require extensive work by a qualified technician to restore the unit to its normaloperation.If the unit has been dropped or the cabinet has been damaged.When the unit exhibits a distinct change in performance, this indicates a need for service.

EXAMPLE OF ANTENNA GROUNDING AS PER THE NATIONAL ELECTRICAL CODE

ANTENNADISCHARGE UNIT(NEC SECTION 810-20)

ANTENNA LEADIN WIRE

GROUNDING CONDUCTORS(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDINGELECTRODE SYSTEM(NEC ART 250, PART H)

GROUNDCLAMP

ELECTRIC SERVICEEQUIPMENT

NEC-NATIONAL ELECTRICAL CODE

S2898A

IMPORTANT SAFEGUARDS (CONTINUED)

Remove the TV/DVD/VCR block from the main unit and the Fig. 1 below can be seen.(Refer to item 1 of the DISASSEMBLY INSTRUCTIONS.)Remove the screw 1 of the Deck Chassis and remove the Loading Motor.Rotate the Pinch Roller Cam in the direction of the arrow by hand to slacken the Video Tape.(Refer to Fig. 2)Rotate the Clutch Ass'y either of the directions to wind the Video Tape in the Cassette Case.Repeat the above step 3~4. Then take out the Video Cassette from the Deck Chassis. Be careful not toscratch on the tape.

TAPE REMOVAL METHOD AT NO POWER SUPPLY

Fig. 1

Pinch Roller Cam

Main CamClutch Ass'y

Main Chassis (Front Side)

Loading Motor

Screw 1

Capstan DD Unit

Fig. 2

Remove the Back Cabinet, TV//DVD/VCR Block and DVD TOP. (Refer to item 1 of the DISASSEMBLYINSTRUCTIONS.)Slide the Rack Loading (White) toward the arrow direction by using a minus driver to release the lock.(Refer to Fig. 1)Draw the Tray.

DISC REMOVAL METHOD AT NO POWER SUPPLY

Fig. 1

DVD DeckRack Loading(White)

TRAY LOCK

Tray cannot be opened by setting the Tray Lock, please follow the steps below.

Turn Unit ON.Set the DVD to the Stop Mode.Press and hold the 'STOP(DVD)' key on the front panel.Simultaneously press and hold the '9' key on the remote control unit.Hold both keys for more than 3 seconds.Press the OPEN/CLOSE key on the front panel to check the Tray Lock setting.

1.2.3.4.5.6.

NB: No indications on the screen when the Tray Lock is setting.

To unlock the Tray Lock, please follow the steps below.

NB: The above procedure will reset ALL of the player's settings to the default factory state.

Turn Unit ON.Set the DVD to the Stop Mode.Set the VOLUME to minimum.Press and hold the 'REC/OTR' button on the front panel.Simultaneously press and hold the '4' key on the remote control unit.Hold both keys for more than 2 second.The On Screen Display message 'INITIALIZE5 COMPLETE' will appear.The Tray Lock has now been cleared.

1.2.3.4.5.6.7.8.

If the stored 4 digit password in the Rating Level menu needs to be cancelled, please follow the stepsbelow.

Turn Unit ON.Set the DVD to the Stop Mode.Check that the 'No disk' is displayed on the screen.Press and hold the 'STOP(DVD)' button on the front panel.Simultaneously press and hold the '2' key on the remote control unit.Hold both keys for more than 2 second.The On Screen Display message 'PASSWORD CLEAR' will appear.The 4 digit password has now been cleared.

1.2.3.4.5.6.7.8.

PARENTAL CONTROL - RATING LEVEL4 DIGIT PASSWORD CANCELLATION

TABLE OF CONTENTSA1-1A1-2A1-2A1-3~A1-5A1-6A1-6A1-7A1-7A2-1A3-1~A3-8

B1-1, B1-2B2-1~B2-6B3-1~B3-4B4-1B5-1, B5-2C1-1, C1-2C2-1C3-1, C3-2C4-1D1-1D1-1D2-1~D2-4D3-1~D3-6

E-1, E-2E-3, E-4E-5, E-6E-7, E-8E-9, E-10E-11, E-12E-13, E-14E-15, E-16E-17, E-18E-19, E-20E-21, E-22

F-1, F-2F-3~F-6F-7, F-8

G-1, G-2G-3, G-4G-5, G-6G-7, G-8G-9, G-10G-11, G-12G-13, G-14G-15, G-16G-17, G-18G-19, G-20G-21, G-22G-23, G-24G-25, G-26G-27, G-28G-29, G-30G-31, G-32G-33, G-34G-35, G-36H-1~H-3I1-1~I1-3I2-1, I2-2I3-1J1-1, J1-2J2-1J3-1J4-1~J4-6

CAUTION .................................................................................................................................SERVICING NOTICES ON CHECKING ..................................................................................HOW TO ORDER PARTS .......................................................................................................IMPORTANT WARNING .........................................................................................................TAPE REMOVAL METHOD AT NO POWER SUPPLY .........................................................DISC REMOVAL METHOD AT NO POWER SUPPLY ..........................................................PARENTAL CONTROL RATING LEVEL ...............................................................................TRAY LOCK .............................................................................................................................TABLE OF CONTENTS ...........................................................................................................GENERAL SPECIFICATIONS ................................................................................................DISASSEMBLY INSTRUCTIONS

1. REMOVAL OF MECHANICAL PARTS AND P. C. BOARDS .........................................2. REMOVAL OF VCR DECK PARTS ................................................................................3. REMOVAL OF DVD DECK PARTS ................................................................................4. REMOVAL OF ANODE CAP ...........................................................................................5. REMOVAL AND INSTALLATION OF FLAT PACKAGE IC ............................................

KEY TO ABBREVIATIONS .....................................................................................................SERVICE MODE LIST .............................................................................................................PREVENTIVE CHECKS AND SERVICE INTERVALS ...........................................................WHEN REPLACING EEPROM (MEMORY) IC ......................................................................SERVICING FIXTURES AND TOOLS ....................................................................................PREPARATION FOR SERVICING ..........................................................................................MECHANICAL ADJUSTMENTS .............................................................................................ELECTRICAL ADJUSTMENTS ...............................................................................................BLOCK DIAGRAMS

DVD.......................................................................................................................................Y/C/AUDIO/HEAD AMP .......................................................................................................MICON ..................................................................................................................................IN/OUT ..................................................................................................................................CHROMA/IF ..........................................................................................................................SOUND AMP/SURROUND ..................................................................................................HiFi/DEMODULATOR ..........................................................................................................DIGITAL COMB FILTER ......................................................................................................DVD IN/OUT .........................................................................................................................REGULATOR........................................................................................................................TV .........................................................................................................................................

PRINTED CIRCUIT BOARDSDVD.......................................................................................................................................VCR.......................................................................................................................................DEFLECTION/CRT/OPERATION/RELAY/SW ....................................................................

SCHEMATIC DIAGRAMSMPEG/MICON ......................................................................................................................

MEMORY..............................................................................................................................RF AMP/DSPAUDIO/VIDEO ......................................................................................................................Y/C/AUDIO/HEAD AMP .......................................................................................................MICON ..................................................................................................................................IN/OUT ..................................................................................................................................CHROMA/IF ..........................................................................................................................SOUND AMP/SURROUND ..................................................................................................HiFi/DEMODULATOR ..........................................................................................................DIGITAL COMB FILTER ......................................................................................................DVD IN/OUT .........................................................................................................................REGULATOR1......................................................................................................................TV POWER ...........................................................................................................................DEFLECTION .......................................................................................................................CRT/OPERATION ................................................................................................................RELAY/SW/FG .....................................................................................................................

INTERCONNECTION DIAGRAM ............................................................................................WAVEFORMS ..........................................................................................................................MECHANICAL EXPLODED VIEWS ........................................................................................CHASSIS EXPLODED VIEWS ................................................................................................DVD DECK EXPLODED VIEWS .............................................................................................MECHANICAL REPLACEMENT PARTS LIST ......................................................................CHASSIS REPLACEMENT PARTS LIST ...............................................................................DVD DECK REPLACEMENT PARTS LIST ............................................................................ELECTRICAL REPLACEMENT PARTS LIST ........................................................................

GENERAL SPECIFICATIONS

G-1 TV CRT CRT Size / Visual Size 20 inch / 508.0mmVSystem CRT Type Flat

Deflection 90 degreeMagnetic Field BV/BH + 0.45 G / 0.18 G

Color System NTSCSpeaker 2 Speaker

Position FrontSize 1.8 x 3.9 InchImpedance 8 ohm

Sound Output MAX 1.5W + 1.5W10%(Typical) 1.5W + 1.5W

G-2 VCR System VHS Player / RecorderSystem Video System NTSC

Hi-Fi STEREO YesNTSC PB -Deck DECK OVD-7

Loading System FrontMotor 3

Heads Video Head 4 Heads

FM Audio Head 2 Heads

Audio /Control Mono /YesErase(Full Track Erase) Yes

Tape Rec PAL -Speed NTSC SP/SLP(EP)

Play PAL -NTSC SP/SLP(EP)

Fast Forward / Rewind Time (Approx.) at 25oC FF:1'48"/REW:1'48"with Cassette T-120

Forward/Reverse NTSC or PAL-M SP/SLP(EP)=3x,5x / 9x,15xPicture SearchFrame Advance YesSlow Speed 1/10

G-3 DVD System Color System NTSCDisc DVD, CD-DA, CD-R/RW, Video CDDisc Diameter 120 mm , 80 mmDeck Disc Loading System Front Loading

Motor 2 MotorsPick up 1-Lens 2-Beams SystemPlayback time(Max) DVD 1-Layer 135min (4.7GB)

DVD 2-Layer 245min (8.5GB)CD 74minVideo CD 74min

Search speed Fwd 2-20 times / 4 stepActual 2-45 times (DVD, VIDEO CD)

4-40 times (CD)Rev 2-20 times / 4 step

Actual 2-45 times (DVD, VIDEO CD)4-40 times (CD)

Slow speed Fwd 1/7 - 1/2 timesActual --

Rev --Actual --

G-4 Tuning Broadcasting System US System MSystem Tuner and System 1 Tuner

Receive CH Destination US(w/CATV)Tuning System F-SynthInput Impedance VHF/UHF 75 ohmCH Coverage 2~69, 4A,A-5~A-1, A~I, J~W,W+1~W+84

Intermediate Picture(FP) 45.75MHzFrequency Sound(FS) 41.25MHz

FP-FS 4.5MHzPreset CH NoStereo/Dual TV Sound US-StereoTuner Sound Muting Yes

G-5 Signal Video Signal Input Level 1 V p-p/75 ohmOutput Level 1 V p-p/75 ohmS/N Ratio (Weighted) at DVD Mode 65dBS/N Ratio (Weighted) at VCR Mode 50dBHorizontal Resolution at DVD Mode 400 Lines Horizontal Resolution at VCR(SP)Mode 220 Lines

RGB Signal Output Level -Audio Signal Input Level -8.0dBm/50k ohm

VCR Output Level(0dB=0.775Vrms) -8.0dBm/1k ohmDVD Output Level(-20dBFs 0dBFs=2.0Vrms) -12.0dBm/1k ohm

Digital Output Level 0.5 V p-p/75 ohm(DVD)S/N Ratio at DVD (Weighted) 90 dBS/N Ratio at VCR (SP)(CCIR Filter:ON) 38 dBHarmonic Distortion at DVD Mode 0.06% (1kHz)Harmonic Distortion at VCR(SP) Mode 1.5% (1kHz) TypicalFrequency Response :

DVD Mode at DVD 4Hz - 22kHzat Video CD 4Hz - 20kHz

at SVCD -at CD 4Hz - 20kHz

VCR Mode at SP 100Hz - 10kHzat LP -

at SLP 100Hz - 4kHzHi-Fi Audio Signal Dynamic Range : More than 90 dB

Frequency Response : 20Hz - 20kHzWow And Flutter : Less than 0.01 %WrmsChannel Separation : More than 60 dBHarmonic Distortion : Less than 1.0 %

G-6 Power Power Source AC 120V,60HzDC -

Power Consumption at AC 110 W at 120 V 60 Hzat DC -

Stand by (at AC) 4 W at 120 V 60 HzPer Year -

Protector Power Fuse YesSafety Circuit YesIC Protector(Micro Fuse) NoDew Sensor No

G-7 Regulation Safety CSARadiation ICX-Radiation HWCLaser DHHS

G-8 Temperature Operation +5oC ~ +40oCStorage -20oC ~ +60oC

G-9 Operating Humidity Less than 80% RH

G-10 On Screen Menu YesDisplay Menu Type Icon(TV/VCR) System Setup Yes

Clock Set YesOn/Off Timer Set YesAuto Clock On/Off YesStandard Time YesDaylight Saving Time Yes

TV Setup YesLanguage YesPicture YesAudio YesPicture Preference Yes

Channel Setup YesTV/CATV YesAuto CH Memory YesAdd/ Delete Yes

V-chip Setup NoTape Setup Yes

Timer Rec Set YesAuto Repeat On/Off Yes

G-CODE(or SHOWVIEW or PLUSCODE)No. Entry NoClock / Date YesTV/VCR YesDVD YesCH/AV(LINE) YesTape Counter(Linear Counter) YesTape Speed YesSleep Time YesStereo/Audio Output Yes

Bilingual NoSAP Yes

Control Volume YesLevel Brightness/Contrast/Sharpness/Color Yes

Tint YesBass/Treble/Balance YesManual Tracking Yes

Play/Stop/FF/Rew/Rec/OTR/T-Rec/Pause/Eject/Tape In (Symbol Mark) YesAuto Tracking/Manual Tracking YesCaption / Text YesIndex NoMute YesHi-Fi YesRepeat YesZero Return YesDEW No

G-11 On Screen Menu (DVD) YesDisplay Menu Type Character(DVD) Language Yes

Menu YesSubtitle YesAudio Yes

Picture YesTV Screen Size YesOSD Display On/Off YesJPEG Interval YesSelect Files Yes

Sound YesDRC (Dynamic Range Control) Yesdts Decode NoOutput(5.1ch/ 2ch) NoSurround On/Off NoCenter On/Off NoSub Woofer On/Off No

Parental YesPassword Lock/ Un Lock YesRating Level Yes

Other YesOSD Language(Set up Language) YesOutput(RGB/Composite) No

Open YesClose YesNo disc YesReading YesPlay YesStill/Pause YesStop YesProhibit Mark YesStep YesSkip(>>|) YesSkip(|<<) YesRandom Yes (CD, VIDEO CD, MP3, WMA, JPEG )Repeat YesSlow+ ## YesSlow- ## NoSearch+ ## YesSearch- ## YesJump YesResume YesTitle No. Yes Chapter No. YesTrack No. YesTime YesSub Title No. YesAngle No. YesVocal On/Off YesAudio No. YesAudio Stereo L/R Yes (Video CD)Zoom YesMarker No. NoProgram Play Back Yes (CD, VIDEO CD, MP3, WMA, JPEG )Surround On/Off NoScreen Saver NoMP3, WMA, JPEG Folder Name Yes

File Name YesFile No Yes

Time Yes (MP3, WMA Only)Track No Yes

G-12 OSD Language TV/VCR English French SpanishDVD English French Spanish

G-13 Clock,Timer Calendar 1990/1/1 ~ 2081/12/31and Timer Timer Events 8 Program/ 1 MonthBack-up One Touch Recording Max Time 6 Hours

OTPB Valid Time -Sleep Timer Max Time 120 Min

Step 10 MinOn/Off Timer Program(On Timer / Off Timer) 1 ProgramAuto Shut Off No Signal 15 Min

No Operation - MinTimer Back-up (at Power Off Mode) 5 Sec

G-14 Remote Unit(for TOSHIBA) RC-FGControl Glow in Dark Remocon YesUnit Format NEC

Custom Code 40-BFh,44-BBhPower Source Voltage(D.C) 3V

UM size x pcs UM-4 x 2 pcsTotal Keys 48 KeyKeys TV/VCR Yes

DVD Yes

Power Yes

Channel- Yes

Channel+ Yes

Volume- Yes

Volume+ Yes

Display Yes

Sleep Yes

Audio Select Yes

Mute Yes

Channel Return / Skip- Yes

Closed Caption / Skip+ Yes

T-REC Yes

Rec(T-Rec/OTR) Yes

Rec/OTR Yes

Slow+ Yes

Play Yes

Stop Yes

Rew Yes

F. Fwd Yes

Pause / Still Yes

CM Skip / Jump Yes

SP/SLP / Return Yes

Counter Reset / Angle Yes

Zero Return / Subtitle Yes

Input Select / Zoom Yes

Menu /Set Up Yes

Program / Repeat A-B Yes

D.Tracking / Top Menu Yes

Tracking+ / DVD Menu Yes

Tracking- / Play Mode Yes

Cancel/Clear Yes

3D Surround No

Cursor Up Yes

Cursor Down Yes

Cursor Left Yes

Cursor Right Yes

Enter YesVCR Plus+ NoOne More Search NoRemain/Counter NoEject NoIndex- NoIndex+ No

G-15 Features Auto Head Cleaning YesAuto Tracking YesHQ (VHS Standard High Quality) YesAuto Power On, Auto Play, Auto Rewind, Auto Eject YesVIDEO PLUS+(SHOWVIEW,G-CODE) NoAuto Clock YesForward / Reverse Picture Search YesAuto CH Memory YesSurround YesStable Sound YesClosed Caption YesTV Auto Shut off Function YesEnd Call NoIndex Search NoSQPB NoCATV YesCM Skip(30sec x 6 Times) YesComb Filter (2Lines) YesVM Circuit NoTV Monitor NoProgram Extend NoChoke Coil NoEnergy Star YesProtect of FBT Leak Circuit YesZero Return YesPower On Memory NoDirty Head NoV-chip USA V-chip No

CANADA V-chip NoParental Lock (DVD Only) YesTray Lock YesAuto Stop (Pause, and Resume Stop after 5min.) YesVideo CD Playback YesSVCD Playback No

Overlay Graphics And Text NoCommand List NoEntry Point Jump No

MP3 Playback YesWMA Playback YesJPEG Playback YesDigital Out (Dolby Digital) Yes

(MPEG) Yes(PCM) Yes(DTS) Yes

Down Mix Out (Dolby Digital) Yes(DTS) No

TruSurround NoScreen Saver NoPicture Preference YesAuto Setup YesAudio DAC 192kHz / 24bitCopy (Disc to Tape) Yes (by Conditioning)

G-16 Accessories Owner's Manual Language English/Frenchw/Guarantee Card Yes

Remote Control Unit YesBattery Yes

UM size x pcs UM-4 x 2 pcsOEM Brand No

Rod Antenna NoPoles -Terminal -

Loop Antenna NoTerminal -

U/V Mixer No300 ohm to 75 ohm Antenna Adapter YesAntenna Change Plug NoDC Car Cord (Center+) NoAC Plug Adapter NoAC Cord NoAV Cord (2Pin-1Pin) NoGuarantee Card NoRegistration Card NoESP Card NoWarning Sheet NoDew/AHC Caution Sheet NoQuick Set-up Sheet NoCircuit Diagram NoService Station List NoImportant Safeguard NoSheet Information (Return) No

G-17 Interface Switch Front Power (Tact) YesChannel Up YesChannel Down YesVolume Up YesVolume Down YesPlay (VCR) YesStop / Eject (VCR) YesF.FWD/Cue (VCR) YesRew/Rev (VCR) YesREC/OTR (VCR) YesPlay (DVD) YesStop (DVD) YesSkip+ /Search+ (DVD) YesSkip- /Search- (DVD) YesOpen/Close (DVD) YesInput Select NoMain Power SW No

Indicator Power Yes(Red)REC/OTR Yes(Red)T-REC Yes(Red)TV/VCR NoDVD No

Terminals Front Video Input RCA x 1Audio Input RCA x 2(Stereo)Other Terminal HeadPhone (Stereo & Mono, 3.5mm)

Rear Video Input RCA x 1Audio Input RCA x 2(Stereo)Video Output RCA x1Audio Output RCA x 2(Stereo)Digital Audio Output Coaxial (DVD Only)VHF/UHF Antenna Input F TypeAC Inlet No

G-18 Set Size Approx. W x D x H (mm) 573 x 481 x 517G-19 Weight Net (Approx.) 27.0kg (59.5lbs)

Gross (Approx.) 30.5kg (67.3lbs)

G-20 Carton Master Carton NoContent -Material -Dimensions W x D x H(mm) -Description of Origin -

Gift Box YesMaterial Double/WhiteDimensions W x D x H(mm) 658 x 575 x 625Design As per Buyer'sDescription of Origin Yes

Drop Test Natural Dropping At 1 Corner / 3 Edges / 6 SurfacesHeight (cm) 31

Container Stuffing (40' container) 216 SetsG-21 Material Cabinet Front PS 94V0 DECABROM

Rear PS 94V0 DECABROMJack Panel -

PCB Non-Halogen Demand NoEyelet Demand Yes

G-22 Environment Pb Free Lead-free Solder NoOther No

Cd Free No

DISASSEMBLY INSTRUCTIONS

1. REMOVAL OF MECHANICAL PARTSAND P.C. BOARDS

1-1: BACK CABINET (Refer to Fig. 1-1)

1.2.3.

Remove the 6 screws 1.Remove the 2 screws 2.Remove the Back Cabinet in the direction of arrow.

1-2: CRT PCB (Refer to Fig. 1-2)

CAUTION: BEFORE REMOVING THE ANODE CAP,DISCHARGE ELECTRICITY BECAUSE ITCONTAINS HIGH VOLTAGE.BEFORE ATTEMPTING TO REMOVE ORREPAIR ANY PCB, UNPLUG THE POWERCORD FROM THE AC SOURCE.

Remove the Anode Cap.(Refer to REMOVAL OF ANODE CAP)Disconnect the following connectors:(CP603B, CP803 and CP805).Remove the CRT PCB in the direction of arrow.

CRT PCBFront Cabinet

Fig. 1-1

Fig. 1-2

Front Cabinet

Back Cabinet

1-3: TV/DVD/VCR BLOCK (Refer to Fig. 1-3)

Remove the 2 screws 1.Disconnect the following connectors:(CP303, CP404 and CP1704).Remove the TV/DVD/VCR Block in the direction of arrow.

Fig. 1-3

1-4: VCR DECK (Refer to Fig. 1-4)

Do not remove the cable at the FE Head section. The FEHead may be damaged if you remove the cable by force.

1.2.3.4.5.6.7.8.9.10.11.

Remove the 2 screws 1.Remove the VCR Top.Remove the 2 screws 2.Remove the VCR Holder.Move the Cassette Holder Ass'y to the back side.Remove the 3 screws 3.Remove the 2 screws 4.Remove the Deck Shield Cover.Remove the screw 5.Remove the FE Head.Disconnect the following connectors:(CP101, CP4501 and CP4502).Remove the VCR Deck in the direction of arrow.

TV/DVD/VCR Block

1Front Cabinet

Fig. 1-4

VCR Top

VCR Holder

Deck Shield Cover

FE Head

VCR Deck

Bottom Plate

1-6: VCR DECK (Refer to Fig. 1-6)

1.2.3.4.5.6.

Remove the 2 screws 1.Remove the DVD Shield.Remove the 4 screws 2.Remove the DVD Block in the direction of arrow (A).Remove the 2 screws 3.Remove the Operation PCB in the direction of arrow (B).

Fig. 1-6

1-7: DVD PCB/DVD DECK (Refer to Fig. 1-7)

2.3.4.

5.6.7.8.

Make the short circuit on the position as shown Fig. 1-7using a soldering. If you remove the DVD Deck with nosoldering, the Laser may be damaged.Remove the 3 screws 1.Remove the DVD Top in the direction of arrow (A).Disconnect the following connectors:(CP2601, CP2602 and CP2603).Remove the 4 screws 2.Remove the DVD Deck in the direction of arrow (B).Remove the 4 screws 3.Remove the DVD PCB in the direction of arrow (C).

NOTEWhen the installation of the DVD Deck, remove all thesoldering on the short circuit position after the connection ofPick Up PCB and DVD PCB connector.

DVD Block

DVD Shield

Operation PCB

Bottom Plate

1-8: DEFLECTION PCB (Refer to Fig. 1-8)

1.2.3.

Remove the 2 screws 1.Remove the 3 screws 2.Remove the Deflection PCB in the direction of arrow.

Fig. 1-8

Deflection PCB

Bottom Plate

Fig. 1-7

Angle Deck

DVD PCB

Pick Up PCB

DVD Top

Make the short circuitusing a soldering.

DVD Deck

1-5: VCR PCB (Refer to Fig. 1-5)

1.2.3.4.

Remove the 6 screws 1.Remove the screw 2.Remove the AV Jack Shield.Disconnect the following connectors:(CP001, CP602B, CP604, CP2201, CP8001 and CP8002).Remove the VCR PCB in the direction of arrow.

Fig. 1-5

12VCR PCB

Bottom Plate

AV Jack Shield

2. REMOVAL OF VCR DECK PARTS2-1: TOP BRACKET (Refer to Fig. 2-1)

Extend the 2 supports 1.Slide the 2 supports 2 and remove the Top Bracket.

After the installation of the Top Bracket, bend the support1 so that the Top Bracket is fixed.

Top Bracket

Main Chassis

Top Bracket

Main Chassis

Fig. 2-1

1.2.3.

2-2: CASSETTE HOLDER ASS'Y (Refer to Fig. 2-2)

Move the Cassette Holder Ass'y to the front side.Push the Locker R to remove the Cassette Side R.Remove the Cassette Side L.

Fig. 2-2

Link Unit Main Chassis

Main Chassis

Cassette Side L

Cassette Side R

Locker R

2-3: CASSETTE SIDE L/R (Refer to Fig. 2-3-A)

Remove the Locker Spring.Unlock the 4 supports 1 and then remove the CassetteSide L/R.Unlock the support 2 and then remove the Locker R.

Locker Spring

Cassette Side LCassette Side R

Locker R

Cassette Holder1

In case of the Locker R installation, check if the oneposition of Fig. 2-3-B are correctly locked.When you install the Cassette Side R, be sure to movethe Locker R after installing.

Locker R

Check if this positionis locked.Cassette Side R

Fig. 2-3-B

2-4: LINK UNIT (Refer to Fig. 2-4)

1.2.3.

Set the Link Unit to the Eject position.Unlock the support 1.Remove the (A) side of the Link Unit first, then removethe (B) side.

Fig. 2-4

Link Unit

Main Chassis

Link Unit

Main Chassis

Fig. 2-3-A

2-5: LINK LEVER/FLAP LEVER (Refer to Fig. 2-5)

1.2.3.

Extend the support 1.Remove the Link Lever.Remove the Flap Lever.

Fig. 2-5

Link Lever

Flap Lever1

2-6: LOADING MOTOR/WORM (Refer to Fig. 2-6-A)

1.2.3.

Remove the screw 1.Remove the Loading Motor.Remove the Worm.

Fig. 2-6-A

Loading Motor

• Screw Torque: 3 ± 0.5kgf•cm

Main Chassis

2-7: TENSION ASS’Y (Refer to Fig. 2-7-B)

2.3.4.5.6.

Turn the Pinch Roller Cam clockwise so that the TensionHolder hook is set to the position of Fig. 2-7-A to movethe Tension Arm Ass’y.Remove the Tension Spring.Unlock the 2 supports 1 and remove the Tension Band.Unlock the support 2 and remove the Tension Arm Ass’y.Unlock the support 3 and remove the Tension Connect.Float the hook 4 and turn it clockwise then remove theTension Holder.

Fig. 2-7-B

Tension BandTension Connect

Tension SpringTension Arm Ass’y

Tension Holder

In case of the Tension Band installation, note the direc-tion of the installation. (Refer to Fig. 2-7-C)In case of the Tension Band installation, install correctlyas Fig. 2-7-D.In case of the Tension Connect installation, install as thecircled section of Fig. 2-7-E.

Fig. 2-7-C

Tension BandTension Connect

Tension Arm Ass’y

Fig. 2-7-A

In case of the Worm installation, check if the value of theFig. 2-6-B is correct.In case of the Loading Motor installation, hook the wireon the Cassette Opener as shown Fig. 2-6-C.When installing the wires between Capstan DD Unit andLoading Motor, connect them correctly as shown Fig. 2-6-D.

Loading Motor Capstan DD Unit

Fig. 2-6-DWhite

Fig. 2-6-B

19.2 ± 0.1mm

Safety surface for pressingof the insert.

Fig. 2-6-C

Loading Motor

Cassette Opener

Fig. 2-7-D

Tension Connect

Tension Band

Tension ConnectTension Band

Fig. 2-7-E

Tension Connect

Main Chassis

2-8: T BRAKE ARM/T BRAKE BAND (Refer to Fig. 2-8-A)

Remove the T Brake Spring.Turn the T Brake Arm clockwise and bend the hooksection to remove it.Unlock the 2 supports 1 and remove the T Brake Band.

Fig. 2-8-A

T Brake Band

Hook section

T Brake Arm

T Brake Spring

1. In case of the T Brake Band installation, install correctlyas Fig. 2-8-B.

Fig. 2-8-B

T Brake Arm

T Brake Band

T Brake Arm

T Brake Band

2-9: S REEL/T REEL/IDLER ARM ASS’Y/IDLER GEAR(Refer to Fig. 2-9-A)

1.2.3.

Remove the S Reel and T Reel.Remove the 2 Polyslider Washers 1.Remove the Idler Arm Ass’y and Idler Gear.

Take care not to damage the gears of the S Reel and TReel.The Polyslider Washer may be remained on the back ofthe reel.Take care not to damage the shaft.Do not touch the section “A” of S Reel and T Reel. (Usegloves.) (Refer to Fig. 2-9-A) Do not adhere the stainson it.When you install the reel, clean the shaft and grease it.(If you do not grease, noise may be heard in FF/REWmode.)After installing the reel, adjust the height of the reel.(Refer to MECHANICAL ADJUSTMENT)

Fig. 2-9-A

Idler Gear

Idler Arm Ass’y

S Reel

T Reel(A)

In case of the S Reel and T Reel installation, check if thecorrect parts are installed. (Refer to Fig. 2-9-B)In case of the Idler Arm Ass’y installation, install correctlyas Fig. 2-9-C. And also set it so that the section “B” ofFig. 2-9-A is placed under the Main Chassis tab.

Fig. 2-9-BBig Hole(S Reel)

Small Hole(T Reel)

Fig. 2-9-C

Clutch GearIdler Arm Ass’y

Idler Arm Ass’y

Clutch Gear

2-10: CASSETTE OPENER/PINCH ROLLER BLOCK/P5ARM ASS’Y (Refer to Fig. 2-10-A)

Unlock the support 1 and remove the Cassette Opener.Remove the Pinch Roller Block and P5 Arm Ass’y.

Fig. 2-10-A

Cassette Opener1

Pinch Roller Block

P5 Arm Ass’y

Main Chassis

Do not touch the Pinch Roller. (Use gloves.)In case of the Pinch Roller Block and the Pinch RollerCam installation, install correctly as Fig. 2-10-B.

Fig. 2-10-B

Pinch Roller Block Can be seen the hole ofthe Pinch Roller Cam.

P5 Arm Ass’y

Can be seen the hole of theMain Cam.

2-11: A/C HEAD (Refer to Fig. 2-11-A)

1.2.3.4.

Remove the screw 1.Remove the A/C Head Base.Remove the 3 screws 2.Remove the A/C Head and A/C Head Spring.

Do not touch the A/C Head. (Use gloves.)When you install the A/C Head Spring, install as shown inFig. 2-11-B.When you install the A/C Head, tighten the screw (1) first,then tighten the screw (2), finally tighten the screw (3).

Fig. 2-11-A

A/C Head

A/C Head Spring

A/C Head Base

• Screw Torque: 5 ± 0.5kgf•cm (Screw 1)

Fig. 2-11-BSpring Position

2-12: FE HEAD (RECORDER ONLY) (Refer to Fig. 2-12)

Remove the screw 1.Remove the FE Head.

Fig. 2-12

FE Head

• Screw Torque: 5 ± 0.5kgf•cm• The FE Head is not installed on the Video Cassette Player.

2-13: AHC ASS'Y/CYLINDER UNIT ASS'Y(Refer to Fig. 2-13)

Unlock the support 1 and remove the AHC Ass'y.Disconnect the following connector: (CD2001)Remove the 3 screws 2.Remove the Cylinder Unit Ass'y.

1.2.3.4.

When you install the Cylinder Unit Ass'y, tighten thescrews from (1) to (3) in order while pulling the Ass'ytoward the left front direction.

Fig. 2-13

Cylinder Unit Ass'y

2• Screw Torque: 3 ± 0.5kgf•cm

AHC Ass'y

2-14: CAPSTAN DD UNIT (Refer to Fig. 2-14-A)

1.2.3.

Remove the Capstan Belt.Remove the 3 screws 1.Remove the Capstan DD Unit.

Fig. 2-14-A

Capstan Belt

Capstan DD Unit

2-15: MAIN CAM/PINCH ROLLER CAM/JOINT GEAR(Refer to Fig. 2-15-A)

Remove the E-Ring 1, then remove the Main Cam.Remove the E-Ring 2, then remove the Pinch RollerCam and Joint Gear.

Fig. 2-15-A

Main Cam

Pinch Roller Cam

Joint Gear

1. In case of the Pinch Roller Cam and Main Cam installa-tion, install them as the circled section of Fig. 2-15-B sothat the each markers are met. (Refer to Fig. 2-15-B)And also can be seen the Main Chassis hole through theMain Cam maker hole.

Fig. 2-15-B

Pinch Roller Cam

Marker

Main Cam

2-16: LOADING GEAR S/T UNIT (Refer to Fig. 2-16-A)

Remove the E-Ring 1 and remove the Main LoadingGear.Remove the Main Rod, Tension Lever, Loading Arm SUnit and Loading Arm T Unit.

Main Loading GearMain Rod

Tension Lever

Loading Arm T Unit

Loading Arm S Unit

Fig. 2-16-A

1. In case of the Capstan DD Unit installation, apply thesilicon bond (TSE3843-W) on the position Fig. 2-14-Bcorrectly. (If no silicon bond applied, abnormal noise willbe heard on the deck operation.)(Refer to Fig. 2-14-B, C)

Fig. 2-14-B

Applied position ofsilicon bond

Be careful not to apply the siliconbond to the Pinch Roller.

Fig. 2-14-C

Silicon Bond

Main Chassis

Capstan DD Unit

Part Name: TSE3843-WPart No.: Y118011000

Clutch Ass’y

Ring Spring

Clutch LeverCoupling Gear

Coupling Spring

Clutch Gear

1. When you install the Loading Arm S Unit, Loading Arm TUnit and Main Loading Gear, align each marker. (Referto Fig. 2-16-B)

Fig. 2-16-B

Marker

Main Loading Gear

Loading Arm T Unit Loading Arm S Unit

Marker

2-17: CLUTCH ASS’Y/RING SPRING/CLUTCH LEVER/CLUTCH GEAR (Refer to Fig. 2-17-A)

1.2.3.4.

Remove the Polyslider Washer 1.Remove the Clutch Ass’y and Ring Spring.Remove the Clutch Lever.Remove the Coupling Gear, Coupling Spring and ClutchGear.

Fig. 2-17-A

1. In case of the Clutch Ass’y installation, install it withinserting the spring of the Clutch Ass’y into the dent of theCoupling Gear. (Refer to Fig. 2-17-B)

Fig. 2-17-B

Clutch Ass’y

Coupling Gear

2-18: CASSETTE GUIDE POST/INCLINED BASE S/TUNIT/P4 CAP (Refer to Fig. 2-18-A)

3.4.5.

Remove the P4 Cap.Unlock the support 1 and remove the Cassette GuidePost.Remove the Inclined Base S/T Unit.Remove the screw 2.Remove the LED Reflector.

Fig. 2-18-A

Do not touch the roller of Guide Roller.In case of the P4 Cap installation, install it with parallelfor “A” and “B” of Fig. 2-18-B.In case of the Cassette Guide Post installation, installcorrectly as the circled section of Fig. 2-18-C.

Fig. 2-18-B

“A” “B”

P4 Cap Cassette Opener

Fig. 2-18-C

Cassette Guide Post

Inclined Base SUnit Inclined Base T

P4 Cap

LED Reflector

3. REMOVAL OF DVD DECK PARTSNOTE

1. Do not disassemble the DVD DECK PARTS except listedparts here. Minute adjustments are needed if the disas-semble is done. If the repair is needed except listed parts,replace the DVD MECHA ASS’Y.

3-1: TRAY (Refer to Fig. 3-1-A)

Set the Tray opened. (Refer to the DISC REMOVALMETHOD AT NO POWER SUPPLY)Unlock the support 1 and remove the Tray.

Main Frame Ass’y

Fig. 3-1-A

1. In case of the Tray installation, install them as the circledsection of Fig. 3-1-B so that the each markers are met.

Fig. 3-1-B

Main Frame Ass’y

3-2: MAIN CHASSIS ASS’Y (Refer to Fig. 3-2-A)

1.2.3.

Remove the Main Chassis Ass’y from the Insulator (R).Unlock the support 1.Remove the Main Chassis Ass’y.

Fig. 3-2-A

Insulator (R)(Green)

1Main Frame Ass’y

Main Chassis Ass’y

3-4: CLAMPER ASS’Y/INSULATOR(R)/LEVER SWITCH(Refer to Fig. 3-4-A)

1.2.3.4.

Remove the screw 1.Remove the Lever Switch.Remove the 2 Insulator (R).Press the Clamper and rotate the Clamper Plate clockwise,then unlock the 3 supports 2.Remove the Clamper Plate, Clamper Magnet and Clamper.

Insulator (R)(Green) Insulator (R)

(Green)

Clamper Plate

Clamper Magnet

Main Frame

Lever Switch

Clamper1

Fig. 3-4-A

Fig. 3-2-B

Rack Loading

Move it to the directionof the arrow.

Main Frame Ass’y

Check Lock

1. In case of the Main Chassis Ass’y, install it from (1) to (6)in order. (Refer to Fig. 3-2-B)

Rack Loading Spring

Rack Loading

Main Gear

Main Frame Ass’y

Rack L Spring

3-3: RACK LOADING/MAIN GEAR/ RACK LOADINGSPRING/ RACK L SPRING (Refer to Fig. 3-3)

1.2.3.

Remove the Rack L Spring.Press down the catcher 1 and slide the Rack Loading.Remove the Rack Loading, Rack Loading Spring andMain Gear.

Fig. 3-3

Fig. 3-5-B

Traverse Holder

Main Chassis Ass'y

3-7: RACK FEED ASS'Y (Refer to Fig. 3-7-A)

Remove the screw 1.Remove the Rack Feed 1 Spring, Rack Feed 1/2 andRack Feed Lever.

Lever Switch

The Lever should be positionbetween A and B.

BRack Loading A

When installing the Clamper Magnet, install it with thegreen face up.When installing the wire of the Lever Switch, install itcorrectly as Fig. 3-4-B.When installing the Lever Switch, install it correctly asFig. 3-4-C.In case of the Lever Switch installation, hook the wire onthe Main Frame as shown Fig. 3-4-D.

Fig. 3-4-B

Fig. 3-4-C

Fig. 3-4-D

3-5: TRAVERSE HOLDER/INSULATOR (F)(Refer to Fig. 3-5-A)

Remove the Traverse Holder.Remove the 2 Insulator (F).

Insulator (F)(Black)

Traverse Holder

Insulator (F)(Black)

Fig. 3-5-A

Lever Switch

BlueWhite

From DVD PCB

1. After the installing of the Traverse Holder, check if thewire is like Fig. 3-5-B.

3-6: SWITCH PCB ASS'Y (Refer to Fig. 3-6-A)

Remove the screw 1.Remove the Switch PCB Ass'y.

Rack Feed 1

Rack Feed Lever

Rack Feed 2

Rack Feed 1 Spring

Main Chassis Ass'y

Fig. 3-6-A

When installing the wire of the Switch PCB, install itcorrectly as Fig. 3-6-B.

Fig. 3-6-B

From Relay PCB

Switch PCB Ass'y

Main Chassis Ass'y

Switch PCB Ass'y

Main Chassis Ass'y

Fig. 3-7-A• Screw Torque: 3.5 ± 0.5kgf•cm

3-9: GEAR (Refer to Fig. 3-9-A)

Unlock the support 1.Remove the Middle Gear 1/2/3, Idler Gear and Feed Gear.

Middle Gear 2

Middle Gear 1

Middle Gear 3

Feed GearIdler Gear

Fig. 3-9-A

In case of the Idler Gear installation, install correctly asFig. 3-9-B.When installing the Middle Gear 2, check if the MiddleGear 2 is locked correctly as Fig. 3-9-C.

Fig. 3-9-B

Fig. 3-9-C

After the assembly of the Rack Feed, check if the RackFeed 1/2 is moving smoothly. (Refer to Fig. 3-7-B)In case of the Rack Feed Ass’y installation, install cor-rectly as Fig. 3-7-C.

Moving smoothly

Moving smoothly Fig. 3-7-B

Should not be engaged.

Check the position ofthe Rack Feed Lever.

Fig. 3-7-C

3-8: RELAY PCB ASS’Y (Refer to Fig. 3-8-A)

Remove the screw 1.Remove the Relay PCB Ass’y.

Relay PCB Ass’y

• Screw Torque: 4 ± 0.5kgf•cm 1 Fig. 3-8-A

[OK]Idler Gear

Idler Arm

[NG]Idler Gear

Idler Arm

Check Lock

Middle Gear 2

1. When installing the wire of the Relay PCB, install itcorrectly as Fig. 3-8-B.

Fig. 3-8-B

3-10: IDLER ARM (Refer to Fig. 3-10)

Remove the Idler Arm.1.

Fig. 3-10

Idler Arm

Main Chassis Ass'y

Fig. 3-11-A• Screw Torque: 1 ± 0.5kgf•cm

3-11: FEED MOTOR (Refer to Fig. 3-11-A)

Remove the 2 screws 1.Remove the Feed Motor.Remove the Motor Gear.

1.2.3.

Motor Gear

Feed Motor

Main Chassis Ass'y

In case of the Motor Gear installation, check if the valueof the Fig. 3-11-B is correct.When installing the Feed Motor, check if the cable ispositioned as Fig. 3-11-C.

Fig. 3-11-B

6.1 ± 0.1mm

Safety surface for pressingof the insert.

Feed Motor

Motor Gear

Fig. 3-11-C

Main Chassis Ass'y

Feed Motor

Pass the cablebetween 2 pins.

4. REMOVAL OF ANODE CAPRead the following NOTED items before starting work.

After turning the power off there might still be a potentialvoltage that is very dangerous. When removing theAnode Cap, make sure to discharge the Anode Cap'spotential voltage.Do not use pliers to loosen or tighten the Anode Capterminal, this may cause the spring to be damaged.

REMOVAL

1. Follow the steps as follows to discharge the Anode Cap.(Refer to Fig. 4-1.)Connect one end of an Alligator Clip to the metal part of aflat-blade screwdriver and the other end to ground.While holding the plastic part of the insulated Screwdriver,touch the support of the Anode with the tip of theScrewdriver.A cracking noise will be heard as the voltage is discharged.

Flip up the sides of the Rubber Cap in the direction of thearrow and remove one side of the support.(Refer to Fig. 4-2.)

GND on the CRT

Screwdriver

Alligator Clip

SupportCRT

GND on the CRT

Rubber Cap

CRTSupport

Fig. 4-1

Fig. 4-2

3. After one side is removed, pull in the opposite direction toremove the other.

INSTALLATION

1. Clean the spot where the cap was located with a smallamount of alcohol. (Refer to Fig. 4-3.)

NOTEConfirm that there is no dirt, dust, etc. at the spot wherethe cap was located.

Arrange the wire of the Anode Cap and make sure thewire is not twisted.Turn over the Rubber Cap. (Refer to Fig. 4-4.)

Fig. 4-4

4. Insert one end of the Anode Support into the anode button,then the other as shown in Fig. 4-5.

CRTSupport

Fig. 4-5

Confirm that the Support is securely connected.Put on the Rubber Cap without moving any parts.

Location of Anode Cap

Fig. 4-3

Take care not to damage the Rubber Cap.

5. REMOVAL AND INSTALLATION OF FLATPACKAGE IC

REMOVAL

1. Put the Masking Tape (cotton tape) around the FlatPackage IC to protect other parts from any damage.(Refer to Fig. 5-1.)

Masking is carried out on all the parts located within10 mm distance from IC leads.

Fig. 5-1

Masking Tape(Cotton Tape)

2. Heat the IC leads using a blower type IC desolderingmachine. (Refer to Fig. 5-2.)

Do not add the rotating and the back and forth direc-tions force on the IC, until IC can move back and fortheasily after desoldering the IC leads completely.

Fig. 5-2

Blower type ICdesoldering machine

3. When IC starts moving back and forth easily afterdesoldering completely, pickup the corner of the IC usinga tweezers and remove the IC by moving with the ICdesoldering machine. (Refer to Fig. 5-3.)

Some ICs on the PCB are affixed with glue, so becareful not to break or damage the foil of each ICleads or solder lands under the IC when removing it.

Fig. 5-3

Blower type ICdesoldering machine

Tweezers

Peel off the Masking Tape.Absorb the solder left on the pattern using the BraidedShield Wire. (Refer to Fig. 5-4.)

Do not move the Braided Shield Wire in the verticaldirection towards the IC pattern.

Fig. 5-4

Braided Shield Wire

Soldering Iron

IC pattern

Fig. 5-5

INSTALLATION

1. Take care of the polarity of new IC and then install thenew IC fitting on the printed circuit pattern. Then soldereach lead on the diagonal positions of IC temporarily.(Refer to Fig. 5-5.)

Soldering Iron

Solder temporarily Solder temporarily

2. Supply the solder from the upper position of IC leadssliding to the lower position of the IC leads. (Refer to Fig. 5-6.)

Fig. 5-6

Solder

Soldering Iron

Supply solderingfrom upper positionto lower position

3. Absorb the solder left on the lead using the BraidedShield Wire. (Refer to Fig. 5-7.)

Do not absorb the solder to excess.

Fig. 5-7

Soldering Iron

Braided Shield Wire

4. When bridge-soldering between terminals and/or thesoldering amount are not enough, resolder using a Thin-tip Soldering Iron. (Refer to Fig. 5-8.)

Fig. 5-8

Thin-tip Soldering Iron

5. Finally, confirm the soldering status on four sides of theIC using a magnifying glass.Confirm that no abnormality is found on the solderingposition and installation position of the parts around theIC. If some abnormality is found, correct by resoldering.

When the IC leads are bent during soldering and/orrepairing, do not repair the bending of leads. If thebending of leads are repaired, the pattern may bedamaged. So, always be sure to replace the IC in thiscase.

KEY TO ABBREVIATIONS

A/CACCAEAFCAFTAFT DETAGCAMPANTA.PBAPCASS'YATAUTOA/VBGPBOTBPFBRAKE SOLBUFFB/WCCASECAPCARRCHCLKCLOCK (SY-SE)COMBCONVCPMCTLCYLCYL-MCYL SENSDATA (SY-CE)dBDCDD UnitDEMODDETDEVEEFEMPHENCENVEOTEQEXTFFBCFEFFFGFL SWFMFSCFWDGENGND

:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::

Audio/ControlAutomatic Color ControlAudio EraseAutomatic Frequency ControlAutomatic Fine TuningAutomatic Fine Tuning DetectAutomatic Gain ControlAmplifierAntennaAudio PlaybackAutomatic Phase ControlAssemblyAll TimeAutomaticAudio/VideoBurst Gate PulseBeginning of TapeBandpass FilterBrake SolenoidBufferBlack and WhiteCapacitance, CollectorCassetteCapstanCarrierChannelClockClock (Syscon to Servo)Combination, Comb FilterConverterCapstan MotorControlCylinderCylinder-MotorCylinder-SensorData (Syscon to Servo)DecibelDirect CurrentDirect Drive Motor UnitDemodulatorDetectorDeviationEmitterEmitter FollowerEmphasisEncoderEnvelopeEnd of TapeEqualizerExternalFuseFeed Back ClampFull EraseFast Forward, Flip-flopFrequency GeneratorFront Loading SwitchFrequency ModulationFrequency Sub CarrierForwardGeneratorGround

H.P.FH.SWHzICIFINDINVKILLLEDLIMIT AMPLM, LDMLPL.P.FLUMI.MMAXMINIMIXMMMODMPXMS SWNCNROSCOPEPBPB CTLPB-CPB-YPCBP. CONPDPGP-PRRECREC-CREC-YREEL BRKREEL SREFREGREWREV, RVSRFRMCRYS. CLKS. COMS. DATASEGSELSENSSERSISIFSOSOLSP

:::::::::::::::::::::::::::::::::::::::::::::::::::::::::::::

High Pass FilterHead SwitchHertzIntegrated CircuitIntermediate FrequencyIndicatorInverterKillerLeftLight Emitting DiodeLimiter AmplifierLoading MotorLong PlayLow Pass FilterLuminanceMotorMaximumMinimumMixer, mixingMonostable MultivibratorModulator, ModulationMultiplexer, MultiplexMecha State SwitchNon ConnectionNoise ReductionOscillatorOperationPlaybackPlayback ControlPlayback-ChrominancePlayback-LuminancePrinted Circuit BoardPower ControlPhase DetectorPulse GeneratorPeak-to PeakRightRecordingRecording-ChrominanceRecording-LuminanceReel BrakeReel SensorReferenceRegulated, RegulatorRewindReverseRadio FrequencyRemote ControlRelaySerial ClockSensor CommonSerial DataSegmentSelect, SelectorSensorSearch ModeSerial InputSound Intermediate FrequencySerial OutputSolenoidStandard Play

KEY TO ABBREVIATIONS

STBSWSYNCSYNC SEPTRTRACTRICK PBTPUNREGVVCOVIFVPV.PBVRV.RECVSFVSRVSSV-SYNCVTX'TALY/C

:::::::::::::::::::::::

Serial StrobeSwitchSynchronizationSync Separator, SeparationTransistorTrackingTrick PlaybackTest PointUnregulatedVoltVoltage Controlled OscillatorVideo Intermediate FrequencyVertical Pulse, Voltage DisplayVideo PlaybackVariable ResistorVideo RecordingVisual Search Fast ForwardVisual Search RewindVoltage Super SourceVertical-SynchronizationVoltage TuningCrystalLuminance/Chrominance

SERVICE MODE LIST

This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily.To enter SERVICE MODE, press and hold main unit and remocon key simultaneously.

Releasing of PARENTAL LOCK.Refer to the “PARENTAL CONTROL - RATING LEVEL”.NOTE: The function will only work without the setting of DVD disc at DVD

STOP (DVD) 2 2

REC/OTR 4 2

Initialization of the factory on DVD.NOTE: Do not use this for the normal servicing.

The function will only work without the setting of DVD disc at DVDmode.

Set Key Remocon Key OperationsStandard Time

(seconds)

VOL. (-) MIN 0

VOL. (-) MIN 3

VOL. (-) MIN 4

VOL. (-) MIN 2

VOL. (-) MIN 5

VOL. (-) MIN 6

VOL. (-) MIN 1

VOL. (-) MIN 9

Releasing of V-CHIP PASSWORD.

Horizontal position adjustment of OSD.NOTE: Also can be adjusted by using the Adjustment MENU.Refer to the "ELECTRICAL ADJUSTMENT" (OSD HORIZONTAL).

Adjust the PG SHIFTER automatically.Refer to the "ELECTRICAL ADJUSTMENT" (PG SHIFTER).

Adjust the PG SHIFTER manually.Refer to the "ELECTRICAL ADJUSTMENT" (PG SHIFTER).

Adjusting of the Tracking to the center position.

POWER ON total hours and PLAY/REC total hours are displayed on thescreen.Refer to the "PREVENTIVE CHECKS AND SERVICE INTERVALS"(CONFIRMATION OF HOURS USED).

Can be checked of the INITIAL DATA of MEMORY IC.Refer to the "WHEN REPLACING EEPROM (MEMORY) IC".

Display of the Adjustment MENU on the screen.Refer to the "ELECTRICAL ADJUSTMENT" (On-Screen Display Adjustment).

Initialization of the factory.NOTE: Do not use this for the normal servicing.

If you set a factory initialization, the memories are reset such as theclock setting, the channel setting, the POWER ON total hours, andPLAY/REC total hours.

STOP (DVD) 9 3Tray cannot be opened.Refer to the “TRAY LOCK”.NOTE: No indications on the screen when the Tray Lock is setting.

VOL. (-) MIN FF 2The BOT, EOT, and the Reel Sensor do not work and the VCR deck canbe operated without a cassette tape.Refer to the "PREPARATION FOR SERVICING"

Set Key Set Key OperationsStandard Time

(seconds)

PREVENTIVE CHECKS AND SERVICE INTERVALS

The following standard table depends on environmental conditions and usage.Parts replacing time does not mean the life span for individual parts.Also, long term storage or misuse may cause transformation and aging of rubber parts.The following list means standard hours, so the checking hours depends on the conditions.

: Clean: Check it and if necessary, replace it.

TimeParts Name

500hours

1,000hours

Notes1,500hours

2,000hours

2,500hours

Audio Control Head

Full Erase Head(Recorder only)

Capstan Belt

Pinch Roller

Capstan DD Unit

Loading Motor

Tension Band

Capstan Shaft

Tape RunningGuide Post

Cylinder Unit

Clean those parts incontact with the tape.

Clean the rubber, and partswhich the rubber touches.

Replace when rollingbecomes abnormal.

Clean the Head

T Brake Band

Clutch Ass’y

Idler Arm Ass’y

CONFIRMATION OF HOURS USEDPOWER ON total hours and PLAY/REC total hours can be checked on the screen.Total hours are displayed in 16 system of notation.

NOTE: If you set a factory initialization, the total hours is reset to "0".

1.2.3.

POWER ON total hours.PLAY/REC total hours.

(16 x 16 x 16 x thousands digit value) + (16 x 16 x hundreds digit value) + (16 x tens digit value) + (ones digit value)

INIT 00 0F

POWER ON 0010PLAY/REC 0003

Initial setting content of MEMORY IC.

Set the VOLUME to minimum.Press both VOL. DOWN button on the set and the Channel button (6) on the remote control for more than 2 seconds.After the confirmation of using hours, turn off the power.

PREVENTIVE CHECKS AND SERVICE INTERVALS

CLEANINGNOTE

After cleaning the heads with isopropyl alcohol, do notrun a tape until the heads dry completely. If the headsare not completely dry and alcohol gets on the tape,damage may occur.

1. AUDIO CONTROL HEAD

Clean the Audio Control Head with the cotton sticksoaked by alcohol. Clean the full erase head in thesame manner. (Refer to the figure below.)

2. TAPE RUNNING SYSTEM

When cleaning the tape transport system, use thegauze moistened with isopropyl alcohol.

3. CYLINDER

Wrap a piece of chamois around your finger. Dip it inisopropyl alcohol. Hold it to the cylinder head softly.Turn the cylinder head counterclockwise to clean it (inthe direction of the arrow). (Refer to the figure below.)

Do not exert force against the cylinder head. Do not movethe chamois upward or downward on the head.Use the chamois one by one.

Cylinder HeadAudio Control Head

WHEN REPLACING EEPROM (MEMORY) IC

If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken toensure correct data settings while making reference to TABLE 1.

NOTE: Initial Data setting will not be possible if clock has been set. To reset clock, either unplug AC cord and allow atleast 5 seconds before Power On.No need setting for the position of the mark @ due to the adjustment value.No need setting for after INI 44 due to the adjustment value.

4.5.6.7.8.

9.10.11.The unit will now have the correct DATA for the new MEMORY IC.

Table 1

Fig. 1

ADDRESS is now selected and should "blink". Using the UP or DOWN button on the remote, step through the ADDRESS untilrequired ADDRESS to be changed is reached.Press ENTER to select DATA. When DATA is selected, it will "blink".Again, step through the DATA using UP or DOWN button until required DATA value has been selected.Pressing ENTER will take you back to ADDRESS for further selection if necessary.Repeat steps 3 to 6 until all data has been checked.When satisfied correct DATA has been entered, turn POWER off (return to STANDBY MODE) to finish DATA input.

After the data input, set to the initializing of shipping.Turn POWER on.Press both VOL. DOWN button on the set and the Channel button (1) on the remote control for more than 2 seconds.After the finishing of the initializing of shipping, the unit will turn off automatically.

Enter DATA SET mode by setting VOLUME to minimum.Press both VOL. DOWN button on the set and the Channel button (6) on the remote control for more than 2 seconds.ADDRESS and DATA should appear as FIG 1.

INIT 00 0F

POWER ON 0010PLAY/REC 0003

ADDRESS DATA

0F 40 34 02 C3 DD 47 32 86 44

+0 +1 +2 +3 +4 +5 +6 +7 +8 +9 +A +B +C +D +E +FINI

40 E3 52 03 87 00 48 00 F6

9A 97 8C A5 B7 A5 91 B6 1A 0B

45 31 19 40 00

D0 08 A6 A1 86 4500

10 0F 15 4B 1C 54 83 B2

3D 08 37 16 27 30

88 89 88 FF FF40

00 00 23 FF FF FF 80 88 83@ @

--- --- --- --- --- --- --- --- ------ ---

SERVICING FIXTURES AND TOOLS

Taper nut driver

70909228

Back tension cassette gauge

70909103

Torque cassette gauge(KT-300NR)

70909199

AdapterDial Torque Gauge(10~90gf•cm)(60~600gf•cm)

JG185 Tentelometer

VTR cleaning kit VTR lubrication kit Grease JG002BJG002E

JG002F

JG153 X Value AdjustmentScrewdriver

JG022 Master Plane JG024A Reel Disk HeightAdjustment Jig

Alignment Tape

ST-N5ST-NF

RemarksPart No.Ref. No. Parts Name

JG002B

JG002E

JG002F

APJG002B00

APJG002E00

APJG002F00

Adapter

Dial Torque Gauge (10~90gf•cm)

Dial Torque Gauge (60~600gf•cm)

VSR Torque, Brake Torque (S Reel/T Reel Ass'y)

Brake Torque (T Reel Ass'y)

VSR Torque, Brake Torque (S Reel)

APJG022000JG022 Master Plane Reel Disk Height Adjustment

JG024A APJG024A00 Reel Disk Height Adjustment Jig Reel Disk Height Adjustment

JG153 APJG153000 X Value Adjustment Screwdriver X Value Adjustment

PREPARATION FOR SERVICING

Set the VOLUME to minimum.Press both VOL. DOWN button on the set and the FF button on the set for more than 2 seconds.(The BOT, EOT, and the Reel Sensor do not work and the VCR deck can be operated without a cassette tape.)In case of using a cassette tape, press the STOP/EJECT button to insert or eject a cassette tape.Turn on the power and re-check the cable before checking the trouble points.

JG185 APJG185000 Tentelometer Confirmation of Tape Tension on Playback

MECHANICAL ADJUSTMENTS

1. CONFIRMATION AND ADJUSTMENTRead the following NOTES before starting work.

• Place an object which weighs between 450g~500g on theCassette Tape to keep it steady when you want to makethe tape run without the Cassette Holder. (Do not place anobject which weighs over 500g.)

CONFIRMATION AND ADJUSTMENT OF REELDISK HEIGHT

Turn on the power and set to the STOP mode.Set the master plane (JG022) and reel disk heightadjustment jig (JG024A) on the mechanism framework,taking care not to scratch the drum, as shown in Fig. 1-1-A.While turning the reel and confirm the following points.Check if the surface "A" of reel disk is lower than thesurface "B" of reel disk height adjustment jig (JG024A)and is higher than the surface "C". If it is not passed,place the height adjustment washers and adjust to 10(+2,-0)mm.Adjust the other reel in the same way.

Fig. 1-2-B

1-3: CONFIRMATION OF PLAYBACK TORQUE ANDBACK TENSION TORQUE DURING PLAYBACK

Load a video tape (T-120) recorded in standard speed mode.Set the unit to the PLAY mode.Install the tentelometer (JG185) as shown in Fig. 1-3. Confirmthat the meter indicates 20 ± 2gf in the beginning of playback.

• USING A CASSETTE TYPE TORQUE TAPE (KT-300NR)

After confirmation and adjustment of Tension Postposition (Refer to item 1-2), load the cassette type torquetape (KT-300NR) and set to the PLAY mode.Confirm that the right meter of the torque tape indicates50~90gf•cm during playback in SP mode.Confirm that the left meter of the torque tape indicates25~40gf•cm during playback in SP mode.

Tentelometer(JG185)

Video Tape

Guide RollerP1 PostFig. 1-3

1-2: CONFIRMATION AND ADJUSTMENT OF TENSIONPOST POSITION

Set to the PLAY mode.Adjust the adjusting section for the Tension Arm positionso that the Tension Arm top is within the standard line ofMain Chassis.While turning the S Reel clockwise, confirm that the edgeof the Tension Arm is located in the position describedabove.

Fig. 1-2-A

Standard line of Main Chassis

Tension Arm

0.5mm (Adjusting range)

Reel Disk Height Adjustment Jig(JG024A)

Fig. 1-1-A

Reel Disk

Height AdjustmentWasher2.6x4.7xT0.132.6X4.7xT0.25

Master Plane (JG022)

Fig. 1-1-B

10(+0.2, -0)mm

Master Plane (JG022)

Reel Disk HeightAdjustment Jig(JG024A)

Adjusting section for theTension Arm position

Tension Band

The Tension Arm top willmove to the outside directionof the Main Chassis.

The Tension Arm top willmove to the inside directionof the Main Chassis.

S Reel/Tension Band/TensionConnect/Tension Arm Ass'yT Reel/T Brake Band//T BrakeSpring/T Brake Arm

1-4: CONFIRMATION OF VSR TORQUE

Install the Torque Gauge (JG002F) and Adapter (JG002B)on the S Reel. Set to the Picture Search (Rewind) mode.(Refer to Fig.1-4-B)Then, confirm that it indicates 120~180gf•cm.

If the torque is out of the range, replace the following parts.

Check item

Replacement Part

Idler Ass'y/Clutch Ass'y

S Reel side:

T Reel side:

2. CONFIRMATION AND ADJUSTMENTOF TAPE RUNNING MECHANISM

Tape Running Mechanism is adjusted precisely at thefactory. Adjustment is not necessary as usual. When youreplace the parts of the tape running mechanism because oflong term usage or failure, the confirmation and adjustmentare necessary.

2-1: GUIDE ROLLER

Playback the VHS Alignment Tape.Connect CH-1 of the oscilloscope to TP4501 (Envelope)and CH-2 to TP102 (SW Pulse).Press both VOL. DOWN button on the set and theChannel button (5) on the remote control for more than 2seconds to set tracking to center.Trigger with SW Pulse and observe the envelope. (Referto Fig. 2-1-A)When observing the envelope, adjust the Taper Nut Driverslightly until the envelope will be flat.Even if you press the Tracking Button, adjust so thatflatness is not moved so much.Adjust so that the A : B ratio is better than 3 : 2 as shownin Fig. 2-1-B, even if you press the Tracking Button tomove the envelope (The envelope waveform will begin todecrease when you press the Tracking Button).Adjust the PG shifter during playback.(Refer to the ELECTRICAL ADJUSTMENTS)

After adjustment, confirm and adjust A/C head.(Refer to item 2-2)

CH-2SW Pulse (TP102)

CH-1Track

CH-2Track

CH-1Envelope(TP4501)

Fig. 2-1-A

Fig. 2-1-B

Install the Torque Gauge on the reel disk firmly. Press theREW button to turn the reel disk.

1-5: CONFIRMATION OF REEL BRAKE TORQUE

(S Reel Brake) (Refer to Fig. 1-4-B)

Once set to the Fast Forward mode then set to the Stopmode. While, unplug the AC cord when the Pinch RollerBlock is on the position of Fig. 1-4-A.Move the Idler Ass'y from the S Reel.Install the Torque Gauge (JG002F) and Adapter(JG002B) on the S Reel. Turn the Torque Gauge(JG002F) clockwise.Then, confirm that it indicates 60~100gf•cm.

(T Reel Brake) (Refer to Fig. 1-4-B)

Once set to the Fast Forward mode then set to the Stopmode. While, unplug the AC cord when the Pinch RollerBlock is on the position of Fig. 1-4-A.Move the Idler Ass'y from the T Reel.Install the Torque Gauge (JG002E) and Adapter(JG002B) on the T reel. Turn the Torque Gauge(JG002E) counterclockwise.Then, confirm that it indicates 30~50gf•cm.

Torque Gauge/Adapter(JG002F/JG002B)

T Reel

S Reel

Torque Gauge/Adapter(JG002E/JG002B)

Fig. 1-4-A

The position at FF mode.

The position atSTOP mode.

CassetteOpener

Pinch Roller Block

Capstan DD Unit

Cassette Holder Ass'y

Stop at this position.

Fig. 1-4-B

Entrance Exit

Max A MaxB

A : B ≥ 3 : 2

2-3:2-2:

When the Tape Running Mechanism does not work well,adjust the following items.

CONFIRMATION AND ADJUSTMENT OF AUDIO/CONTROL HEAD

When the height is not correct, turn the screw 3 toadjust the height. Then, adjust the 1~3 again.

Playback the VHS Alignment Tape.Confirm that the reflected picture of stamp mark isappeared on the tape prior to P4 Cap as shown in Fig. 2-2-A.a)

Turn the screw 2 to set the audio level to maximum.Confirm that the bottom of the Audio/ Control Head andthe bottom of the tape is shown in Fig. 2-2-C.c)

When the reflected picture is distorted, turn the screw1 clockwise until the distortion is disappeared.When the reflected picture is not distorted, turn thescrew 1 counterclockwise until little distortion isappeared, then adjust the a).

P4 Cap

Fig. 2-2-A

Audio/Control Head

Fig. 2-2-B

Audio/Control Head

Fig. 2-2-C

TAPE RUNNING ADJUSTMENT(X VALUE ADJUSTMENT)

Confirm and adjust the height of the Reel Disk.(Refer to item 1-1)Confirm and adjust the position of the Tension Post.(Refer to item 1-2)Adjust the Guide Roller. (Refer to item 2-1)Confirm and adjust the Audio/Control Head.(Refer to item 2-2)Connect CH-1 of the oscilloscope to TP102, CH-2 toTP4501 and CH-3 to HOT side of Audio Out Jack.Playback the VHS Alignment Tape.Press both VOL. DOWN button on the set and theChannel button (5) on the remote control for more than 2seconds to set tracking to center.Set the X Value adjustment driver (JG153) to the 4 ofFig. 2-2-B. Adjust X value so that the envelope waveformoutput becomes maximum. Check if the relation betweenAudio and Envelope waveform becomes (1) or (2) of Fig.2-3.

Audio/Control Head

Reflected picture ofStamp Mark

Stamp Mark

0.25±0.05mm

Envelope

CH-3Audio

Fig. 2-3

3. MECHANISM ADJUSTMENT PARTS LOCATION GUIDE

1. Tension Connect2. Tension Arm3. Guide Roller4. Audio/Control Head5. X value adjustment driver hole

6.7.8.9.

P4 PostT Brake SpringT ReelS ReelAdjusting section for the Tension Arm position

ELECTRICAL ADJUSTMENTS

Read and perform these adjustments when repairing thecircuits or replacing electrical parts or PCB assemblies.

CAUTION

Use an isolation transformer when performing any serviceon this chassis.Before removing the anode cap, discharge electricitybecause it contains high voltage.When removing a PCB or related component, afterunfastening or changing a wire, be sure to put the wireback in its original position.When you exchange IC and Transistor for a heat sink,apply the silicon grease on the contact section of the heatsink. Before applying new silicon grease, remove all the oldsilicon grease. (Old grease may cause damages to the ICand Transistor).

BEFORE MAKING ELECTRICALADJUSTMENTS

Prepare the following measurement tools for electricaladjustments.

1. Oscilloscope2. Digital Voltmeter3. Multi-sound Generator4. Pattern Generator

FUNCTIONOSD HOSD CCUT OFFH.POSIH.BLK LH.BLK RV.SIZEV.POSIV.LINVS.CORRV.COMPR.BIASG.BIASB.BIASR.DRVG.DRVB.DRVBRI CENT

NO.000102030405060708091011121314151617

FUNCTIONBRI MAXBRI MINCONT CENTCONT MAXCONT MINCOL CENTCOL MAXCOL MINTINTSHARPSUB BIASH.SIZEPARABOLATRAPEZIUMCOR TOPCOR BTMH.COMPT.STE

NO.181920212223242526272829303132333435

Fig. 1-2

(VCR SECTION)2-1: PG SHIFTER

Connect CH-1 on the oscilloscope to TP102 and CH-2 toTP4201.Playback the alignment tape.Press both VOL. DOWN button on the set and theChannel button (5) on the remote control for more than 2seconds to set tracking to center.Press the VOL. DOWN button on the set and the channelbutton (3) on the remote control for more than 2 secondsuntil the indicator REC disappears. If the indicator RECdisappears, adjustment is completed.

(If the above adjustments doesn't work well:)

Press the VOL. DOWN button on the set and the channelbutton (3) on the remote control for more than 2 secondsuntil the indicator REC disappears.When the REC indicator is blinking, press both VOL.DOWN button on the set and the channel button (4) onthe remote control for more than 2 seconds and adjustthe Tracking +/- button until the arising to the down ofHead Switching Pulse becomes 6.5 ± 0.5H.(Refer to Fig. 2-1-A, B)

Fig. 2-1-B

Fig. 2-1-A

2. BASIC ADJUSTMENTS

On-Screen Display Adjustment

Set the VOLUME to minimum.Press the VOL. DOWN button on the set and theChannel button (9) on the remote control for more than 2seconds to appear the adjustment mode on the screen asshown in Fig. 1-1.

Fig. 1-1

Use the Channel UP/DOWN button or Channel button (0-9) on the remote control to select the options shown inFig. 1-2.Press the MENU button on the remote control to end theadjustments.

00 OSD 9

2-2: CONSTANT VOLTAGE

Set condition is AV MODE without signal.Using the remote control, set the brightness and contrastto normal position.Connect the digital voltmeter to TP401.Adjust the VR1701 until the digital voltmeter is 114 ± 0.5V.

2-3: CUT OFF

2.3.4.

Adjust the unit to the following settings.R.BIAS=127, G.BIAS=127, B.BIAS=127, R.DRV=63,G.DRV=07, B.DRV=63,Place the set with Aging Test for more than 15 minutes.Set condition is AV MODE without signal.Using the remote control, set the brightness and contrastto normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (02) on the remote control toselect "CUT OFF".Adjust the Screen Volume until a dim raster is obtained.

(TV SECTION)

2-5: FOCUS

1.2.3.

Receive the monoscope pattern.Turn the Focus Volume fully counterclockwise once.Adjust the Focus Volume until picture is distinct.

2-4: WHITE BALANCE

NOTE: Adjust after performing CUT OFF adjustment.

Place the set with Aging Test for more than 15 minutes.Receive the gray scale pattern from the PatternGenerator.Using the remote control, set the brightness and contrastto normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (11) on the remote control toselect "R.BIAS".Press the CH. UP/DOWN button on the remote control toselect the "R.BIAS", "G.BIAS", "B.BIAS", "R.DRV","B.DRV" or "G.DRV".Adjust the VOL. UP/DOWN button on the remote controlto whiten the R.BIAS, G.BIAS, B.BIAS, R.DRV, B.DRV,and G.DRV at each step tone sections equally.Perform the above adjustments 5 and 6 until the whitecolor is looked like a white.

2-6: HORIZONTAL POSITION

Receive the monoscope pattern.Using the remote control, set the brightness and contrastto normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (03) on the remote control toselect "H.POSI".Press the VOL. UP/DOWN button on the remote controluntil the SHIFT quantity of the OVER SCAN on right andleft becomes minimum.

2-8: VERTICAL SIZE

Receive the monoscope pattern.Using the remote control, set the brightness and contrastto normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (06) on the remote control toselect "V.SIZE".Press the VOL. UP/DOWN button on the remote controluntil the Up/Down OVER SCAN Quantity becomes equalto the Right/Left OVER SCAN Quantity.

2-9: VERTICAL LINEARITY

NOTE: Adjust after performing adjustments in section 2-8.After the adjustment of Vertical Linearity, reconfirmthe Vertical Position and Vertical Size adjustments.

Receive the monoscope pattern.Using the remote control, set the brightness and contrastto normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (08) on the remote control toselect "V.LIN".Press the VOL. UP/DOWN button on the remote controluntil the SHIFT quantity of the OVER SCAN on upsideand downside becomes minimum.

2-7: VERTICAL POSITION

Receive the monoscope pattern.Using the remote control, set the brightness and contrastto normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (07) on the remote control toselect "V.POSI".Check if the step No. V.POSI is "02".Adjust the VR404 until the horizontal line becomes fit tothe notch of the shadow mask.

2-10: OSD HORIZONTAL

Activate the adjustment mode display of Fig. 1-1.Press the VOL. UP/DOWN button on the remote controluntil the difference of A and B becomes minimum. (Referto Fig. 2-2)

00 OSD 9

Fig. 2-2

2-12: TINT

Receive the color bar pattern. (RF Input)Using the remote control, set the brightness, contrast,color and tint to normal position.Connect the oscilloscope to TP803.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (26) on the remote control toselect "TINT".Press the VOL. UP/DOWN button on the remote controluntil the section "A" becomes a straight line(Refer to Fig. 2-3).Receive the color bar pattern. (Audio Video Input)Press the INPUT SELECT button on the remote controlto set to the AV mode. Then perform the aboveadjustments 2~5.Press the DVD button on the remote control to set to theDVD mode.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (26) on the remote control toselect "TNT".Press the VOL. UP/DOWN button on the remote controlto set the same step numbers as the AV mode.

Fig. 2-3

2-11: BRIGHT CENTER

Receive the monoscope pattern. (RF Input)Using the remote control, set the brightness and contrastto normal position.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (17) on the remote control toselect "BRI CENT".Press the VOL. UP/DOWN button on the remote controluntil the white 10% is starting to be visibleReceive the monoscope pattern. (Audio Video Input)Press the INPUT SELECT button on the remote controlto set to the AV mode. Then perform the aboveadjustments 2~4.Press the DVD button on the remote control to set to theDVD mode.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (17) on the remote control toselect "BRI CENT".Press the VOL. UP/DOWN button on the remote controlto set the same step numbers as the AV mode.

2-13: COLOR CENTER

Receive the color bar pattern. (RF Input)Using the remote control, set the brightness, contrast,color and tint to normal position.Connect the oscilloscope to TP802.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (23) on the remote control toselect "COL CENT".Adjust the VOLTS RANGE VARIABLE knob of theoscilloscope until the range between white 100% and 0%is set to 4 scales on the screen of the oscilloscope.Press the VOL. UP/DOWN button on the remote controluntil the red color level is adjusted to 85 ± 5% of thewhite level. (Refer to Fig. 2-4)Receive the color bar pattern. (Audio Video Input)Press the INPUT SELECT button on the remote controlto set to the AV mode. Then perform the aboveadjustments 2~6.Press the DVD button on the remote control to set to theDVD mode.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (23) on the remote control toselect "COL CENT".Press the VOL. UP/DOWN button on the remote controlto set the same step numbers as the AV mode.

Fig. 2-4

White 0%

White 100%

Red Level

2-14: SUB CONTRAST MAX

Activate the adjustment mode display of Fig. 1-1 andpress the channel button (21) on the remote control toselect "CONT MAX".Press the VOL. UP/DOWN button on the remote controluntil the contrast step No. becomes "60".Receive a broadcast and check if the picture is normal.Press the INPUT SELECT button on the remote controlto set to the AV mode. Then perform the aboveadjustments 1~3.Receive a broadcast and check if the picture is normal.Press the DVD button on the remote control to set to theDVD mode.Activate the adjustment mode display of Fig. 1-1 andpress the channel button (21) on the remote control toselect "CONT MAX".Press the VOL. UP/DOWN button on the remote controlto set the same step numbers as the AV mode.

Please check if the fixed values of the each adjustmentitems are set correctly referring below.

2-15: Confirmation of Fixed Value (step No.)

NO.010405091015181920222425272829303132333435

FUNCTIONOSD CH.BLK LH.BLK RVS.CORRV.COMPG.DRVBRI MAXBRI MINCONT CENTCONT MINCOL MAXCOL MINSHARPSUB BIASH.SIZEPARABORATRAPEZIUMCOR TOPCOR BTMH.COMPT.STE

RF030202070307

100253010

12700302000000000000000

AV030202070307

100253010

12700302000000000000000

DVD030202070307

100253010

12700152000000000000000

Receive the green raster pattern from color bargenerator.Adjust the pair of purity magnets to center thecolor on the screen.Adjust the pair of purity magnets so the color at theends are equally wide.Move the deflection yoke backward (to neck side)slowly, and stop it at the position when the wholescreen is green.Confirm red and blue colors.Adjust the slant of the deflection yoke while watching thescreen, then tighten the fixing screw.

DEFLECTION YOKEDEFLECTION YOKE SCREWMAGNET SCREW

6 POLE MAGNETS4 POLE MAGNETSPURITY MAGNETS

Fig. 3-1

PURITY AND CONVERGENCEADJUSTMENTS

3-1: STATIC CONVERGENCE (ROUGH ADJUSTMENT)

Turn the unit on and let it warm up for at least 30minutes before performing the following adjustments.Place the CRT surface facing east or west to reduce theterrestrial magnetism.Turn ON the unit and demagnetize with a Degauss Coil.

3-3: STATIC CONVERGENCE

3-4: DYNAMIC CONVERGENCE

Adjust after performing adjustments in section 3-3.

Adjust the differences around the screen by movingthe deflection yoke upward/downward and right/left.(Refer to Fig. 3-2-a)Insert three wedges between the deflection yoke andCRT funnel to fix the deflection yoke.(Refer to Fig. 3-2-b)

Fig. 3-2-a

WEDGE WEDGE

WEDGE POSITION

Fig. 3-2-b

Receive the crosshatch pattern from the color bargenerator.Combine red and blue of the 3 color crosshatch patternon the center of the screen by adjusting the pair of4 pole magnets.Combine red/blue (magenta) and green by adjusting thepair of 6 pole magnets.

UPWARD/DOWNWARD SLANT RIGHT/LEFT SLANT

3-2: PURITY

Tighten the screw for the magnet. Refer to the adjustedCRT for the position. (Refer to Fig. 3-1)If the deflection yoke and magnet are in one body,untighten the screw for the body.Receive the green raster pattern from the color bargenerator.Slide the deflection yoke until it touches the funnelside of the CRT.Adjust center of screen to green, with red and blue on thesides, using the pair of purity magnets.Switch the color bar generator from the green rasterpattern to the crosshatch pattern.Combine red and blue of the 3 color crosshatch patternon the center of the screen by adjusting the pair of4 pole magnets.Combine red/blue (magenta) and green by adjusting thepair of 6 pole magnets.Adjust the crosshatch pattern to change to whiteby repeating steps 6 and 7.

NOTENOTE

2. ELECTRICAL ADJUSTMENT PARTS LOCATION GUIDE (WIRING CONNECTION)

CP2201

DVD DECK

OPERATION PCB

DVD PCB

CD2301

CD2001

CP8502

CD4002

CP2601

CP2603

CP2602

CD2251

CP8001

CP1702

CP4502

AC HEADCP603B

TP4501

DVD DECK

TP401VCR DECK

CP802A

CP802B

SPEAKER

CP4503

FE HEAD

VR1701

CD1703CP1704

CRT PCB

DEFLECTION PCB

VCR PCB

802CD1704

CD2302

DVD BLOCK DIAGRAM

READ CHANNEL

IC2601ZR36708TQC

Dual OP-AMPIC2602

BA10358F-E2

FLASH IC4007

SST39VF800A-70-4C-EK-D

MPEG/MICON/DSPIC4001

ZR36762 REG+1.8VIC4003

PQ070XZ01ZP

64M SDRAMIC4005

M12L64164A-7T

Pick up

Loading Motor

Spindle/SledMotor

DVD LOADERDM II

Motor DriverIC2301LA6560

A, B, C, D, E, F

SPDL+/– SPDL_SENS

VCR BLOCK

P.CON+3.3VCD, DVD, LD

RFA_SDEN, DATA, SCLK

EEPROMIC4002

S-24C04BFJ-TB

CD4002

RFAAF_CE, FE, TE, PI

FNN, FNP

VBIASS0, S1

DEFECT, LINK, MIRR, LDON

HOME, TIN SW, TOUT SW

TR+/–, FO+/–

SPDL+/–, SLED+/–

SPINDLE, SLED_PWM

TRACK, FOCUS_DAC

ADC IN 5, 6, 7

S MUTE

HA0~HA20, HD0~HD15

I CDAT2 I CCLK2

P.CON+5V

P.CON+9V

DVD RESET

CP8502

DVD AUDIO LDVD AUDIO R

STEREO DACIC8502

PCM1742KEG/2KDVD AUDIO R

ASDATA0AMCLKABCLKALRCLK

DVD VIDEO

DVD AUDIO L

VIDEO BUFFERQ8502~Q8504

DAC B, C, D

E-1 E-2

Y/C/AUDIO/HEAD AMP BLOCK DIAGRAM

4 35 78 76

H.AMPSW

REC AMP

CP4502

AUDIO REC

AUDIO PB

CTL+HEAD

AUDIOCONTROL 3

AE HEAD(+)

AE HEAD(-)

Y/C/AUDIO/HEAD AMP ICIC4501LA71205M-MPB

BUFFER

TIMMING CCD

DRIVER CLAMP

74H.SW

NLEMPHA

RECFM-EQ

AGCAMP

PBFM-EQ

PBPHASE-EQ

GCAB-UPAMP

ACCAMP

MainCONV

3.58MBPF2

AUTO BIAS

RKILB.D.

3.58MBPF1

DOUBLELIM

SUBLPF

V/ICONV P

RY-LPF

YNR/COMB

N.L.DEEM

Y/C MIX

SYNCSEP

CharaINS.

RV-AGC

LINEAMP

Y/C_CS

Y/C_DATA

Y/C_CLK

H. AMP_SW1

C. ROTARY

ENV. DET

DUMMY_V. SYNC

AUX_V[F/R]

TUNER_VIDEO

NORMAL_A

Y/C_AUDIO

BIAS CTL

H.AMP SW/AUDIO MUTE

C ROTRF SW IN

ENV DET

COMPOUT

BIAS OSC

Q4501, Q4502

AUDIO PB SW

HI-FI/DEMODULATOR HF_COM

COIL, BIAS OSC

X45013.579545MHz

BUFFER

DIGITALCOMB FILTER

HI-FI/DEMODULATOR

SERIAL

DECODER

VCR_A_MUTE

V.REC_ST_H

ALCDET

VIDEO OUT

EP/LP-CH1 (R)

EP/LP-CH2 (L)

CP4501

SP-CH1 (R)

SP_COM

SP-CH2 (L)

EP/LP_COM

HF2 (L)

HF_COM

HF1 (R)

FE HEAD (HOT)

FE HEAD (GND)FE HEAD

CP4503

DETALENH

DVD_VIDEO

Y/C_VIDEO

BUFFER

DVD IN/OUT

Y/C_VIDEO

V SYNC CHROMA/IF

E-3 E-4

SYSCON/TIMER/SERVO ICIC101 OEC8076A

Y/C/AUDIO/HEAD AMP

DRUM PWM

MS SEN-B

POWER FAIL

Y/C CS

DUMMY.V.SYNC

C_ROTARY

IN/OUT

POWER_FAIL

CYL SPEED UP58

CYL_FG/PG65

VCR.A.MUTE 54

CHROMA/IF

LDM CTL78

REMOCON IN

REEL-T3

REEL-S4

REEL SENSQ107

BOT SENSORQ101 EOT SENSOR

REEL SENSQ108

P.CON+5V_C

11 CYL FG/PG

12 CYL DRIVE

CAP PWM33

CAP LIMIT21

CAP FULL32

CAP_F/R64

I LIMIT

CAP CTL1 CAP FG

4 CAP.M F/R

MS SEN-A83

MS_SEN AQ105

MS_SEN BQ104

CAPSTANDD UNIT

H.AMP SW1 99

Y/C_CS

DUMMY_V.SYNC

C.ROTARY

VCR_A_MUTE

H.AMP_SW1

ENV.DET

V.REC START-H 93

89 ENV.DET

V.REC_ST-H

CTL(+) 74

CTL(-) 75

AFT 85

DEGAUSS 60

SCL 18

DEGAUSS_H

REMOCON_IN

TAB SW 97 TAB SW

RESET 1

IC103PST3231NR

SYSTEM RESET IC

EEP ROM ICIC199S-24C04BDP-LA

Y/C DATA 13

Y/C CLK 11

Y/C_DATA

Y/C_CLK

CVN2 50 Y/C VIDEO

COMP 100 COMP

REC/OTR LED

EXT_A_MUTE

EXT_MUTE6

REC_LED

EXT_A_MUTE

EXT_MUTE

ST SELECT 87

HIFI H.SW 26

HIFI ENV 88

ST_SELECT

HIFI_H.SW

HIFI_ENV

SDASCLVCR_A_MUTEV.REC_ST_H

HI-FI/DEMODULATOR

VCR_POWER_ON-H92VCR_POWER_H

EMERGENCY 86 EMERGENCY

MICON BLOCK DIAGRAM

X10132.768KHz

DVD RESET95DVD RESET

T-REC LED90T-REC_LED

RXDVD IN/OUT

X10214.31818MHz

OSCI 38

TV_POWER_HCENT_LED_CTL29

CENT LED SW

CENT LEDD101

10 LDM CTL

CHROMA/IF

BLK 59

VSYNC 45

46 H.SYNC

V.SYNC

TV_POWER_H

TV_MUTE 20

TV_A_MUTE

R OSD_R

2 CAP VCO8 LD/CY_VCO

AT+12V

REGULATOR

DVD_HDVD_H

AV_SW17

AV_SW1

BUFFER

AV_SW235

AV_SW1

AV_SW2COMB FILTER

CVIN 49

TV_POWER_ON-H 56

TV_POWER_HVCR_A_MUTE

VIDEO OUT

SOUND AMP/SURROUND

IN/OUT

PROTECT 94 PROTECT

DIGITALCOMB FILTER

P.CON+5V_C

E-5 E-6

CH.DOWN

REC/OTR

STOP/EJECT

OS2201

REC/OTR

LED D2205

REC LED SW

MUTE SW

Q4202 Q4201

BUFFER

SW_AUDIO_OUT_R

EXT_A_MUTE

SOUND_R+

IN/OUT BLOCK DIAGRAM

VOL UP

VOL DOWN

OPEN/CLOSE

LED D2206T-REC LED

LED D2207POWER LED

REMOCON_IN

TV_POWER_H

T-REC_LED

REC_LED

VCR_A_MUTE

MUTE SW

CH MUTE

MUTE SW

REAR OUT JACKJ4202

HEADPHONE JACKJ2201

SOUND_L+

SP_OUT_R

SP_OUT_L

MUTE SW

EXT_MUTE

JACK_OUT

REAR IN JACKJ4201

FRONT_V_IN

REAR_A_IN_L

REAR_A_IN_R

REAR_V_IN

FRONT VIDEO JACKJ2202

FRONT_A_IN_L

FRONT AUDIO L JACKJ2203

FRONT_A_IN_R

FRONT AUDIO R JACKJ2204

SOUND AMP/SURROUND

DIGITALCOMB FILTER

HI-FI/DEMODULATOR

ZERO SW

D AUDIO DRIVER

COAXIALJ8007

SPDIF_134

DVD IN/OUT

P.CON+5V

P.CON+8V

REGULATOR

SW_AUDIO_OUT_L

E-7 E-8

CHROMA/IF_ ICIC601LA76319M-MPB-E

MOTOR+12V

8.5V REG

REGULATOR

CHROMA/IF BLOCK DIAGRAM

AT+5.7V REG

X6013.579545MHz

P.CON+8V

36 P.CON+5V

10V_REG.IC602 KIA78L10F-RTF

V_SYNC

H.SYNC

COMB FSC

Y/C_VIDEO_Y

DVD_Y/C_Y

V_SYNC

DIGITALCOMB FILTER

DVD IN/OUT

PROTECT

CUT OFF

FROM TO CRTCP603

CLAMP OFF

FROM TO DEFLECTIONCP602

TV_POWER_HTV_POWER_H

EMERGENCYMICON

PROTECT MICON

Y/C/AUDIO/HEAD AMP

P.CON+5V

EMERGENCY

9+B DOWN

E-9 E-10

IN/OUT

25 9 6 8

SOUND AMP ICIC352 AN7522N

SOUND_L+

SOUND_R+

1012 4

SP_OUT_R

SP_OUT_L

SOUND AMP/SURROUND BLOCK DIAGRAM

SPEAKERSP352

SPEAKERSP351

TV_POWER_H

TV_A_MUTE

P.CON+8V

SURROUND-ICIC302

AN5891SA-E1V

SW_AUDIO_OUT_L

SW_AUDIO_OUT_R

SW_AUDIO_OUT_L

REGULATOR

IN/OUT

DVD IN/OUT

SOUND +BTV

E-11 E-12

HI-FI AUDIO/H.AMP/DEM ICIC5501AN3663FBP

HIFI_H.SW

TUNER_AUDIO

VCR_A_MUTE

V. REC_ST-H

HIFI_ENV

ST_SELECT

REAR_A_IN_L

REAR_A_IN_R

HF_COM

Y/C_AUDIO

NORMAL_A

IN/OUT

Y/C/AUDIO/HEAD AMP

P.CON+12V

P.CON+5V_A

INPUT SW

OUTPUT SW

FM LIM

DEM BLOCK

VCO-FOADJ

DBXNOISE

REDUCTION

L/RMIX

RECLPF VCO

HIFI/DEMODULATOR BLOCK DIAGRAM

DVD_A_OUT_L

DVD_A_OUT_RDVD IN/OUT

REGULATOR

10 FRONT_A_IN_R

FRONT_A_IN_L

AUDIO_OUT_L

AUDIO_OUT_R

DIGITALCOMB FILTER

E-13 E-14

Y/C_VIDEO_Y

DIGITAL COMB FILTER BLOCK DIAGRAM

AV_SW1

AV_SW2

DVD_Y/C-C

DVD_VIDEO

JACK_OUT

AUX_V[F/R]

Y/C_VIDEO

REAR_V_IN

FRONT_V_IN

REGULATOR

CHROMA/IF

DIGITAL COMB FILTER IC

IC1501TC90A45F

AV SW ICIC1502 MM1501XNRE

AV SW ICIC1504 MM1501XNRE

VIDEO OUT SW ICIC1505 MM1504XNRE

BUFFER

COMB_FSC

BUFFER

P.CON+5V

P.CON+12V

BUFFER

DVD IN/OUT

Y/C/AUDIO/HEAD AMP

IN/OUT

P.CON+8V

3 10 11

TU001115-V-K015AR_B

12 14 15 17

TUNER_AUDIOHI-FI/DEMODULATOR

TUNER VIDEO

AT+30V

Y/C/AUDIO/HEAD AMP

E-15 E-16

DVD IN/OUT BLOCK DIAGRAM

AUDIO SW ICIC8001 MM1501XNRE

REGULATOR

CP8001

P.CON+9V

P.CON+D5V

P.CON+3.3V

SPDIF-134

CP80022

DVD_RESET

AUDIO-R

AUDIO-L

C (CVBS)

12 CVBS

P.CON+9V_D

P.CON+5V_D

P.CON+3.3V

SPDIF-134

DVD_RESET

MIXER ICIC8004 NJM4580M(TE1)

AUDIO SW ICIC8002 MM1501XNRE

Q8006, Q8007

ZERO MUTESW

IN/OUT

AUDIO_OUT_L

AUDIO_OUT_R

DVD_A_OUT_L

DVD_A_OUT_R

P.CON+12V

AV SW1

DVD_Y/C_Y

DVD_Y/C_C

DVD_VIDEO

CHROMA/IF

Y/C/AUDIO/HEAD AMP

HI-FI/DEMODULATOR

DVD_VIDEO

SW_AUDIO_OUT_L

SW_AUDIO_OUT_R

DIGITALCOMB FILTER

SOUND AMP/SURROUND

E-18E-17

REGULATOR BLOCK DIAGRAM

UNREG+8V

AT+5V OUT

P.CON+5V

P.CON+5V_A

P.CON+12V

P.CON+8V

P.CON+5V_A

UNREG+5V

P.CON+8V

P.CON+5V_C

P.CON+5V OUT ICIC3004KIA278R05PI

P.CON+5V_A OUT ICIC3003KIA278R05PI

P.CON+5V_D OUT ICIC3001KIA278R05PI

P.CON+9V_D OUT ICIC3002KIA278R09PI

BACKUP+5V

BUFFER

MOTOR+12V

P.CON+5V_C SW

AT+12V

VCR_POWER_H

P.CON+5V_A

BACKUP+5V

P.CON+12V

P.CON+8V

IN/OUT

HI-FI/DEMODULATOR

3.3V OUTQ3004

3.3V CTLQ3006

3.3V CTL

P.CON+12V SW

DIGITALCOMB FILTER

P.CON+12V

P.CON+5V_D

P.CON+9V_D

P.CON+3.3V

P.CON+5V

P.CON+8V

8.5V REG

AT5.7V REG

DVD IN/OUT

CHROMA/IF

SOUND AMP/SURROUND

P.CON+5V

P.CON+12V

P.CON+8V

Y/C/AUDIO/HEAD AMP

P.CON+8V SW

Q3008,Q3009 SW

E-19 E-20

TRANSFORMER SWITCHINGT1701

L1703DEGAUSS COIL

DEGAUSS RELAYRY1701

FEED BACKIC1701

PS2561L1-1-V(W)

CURRENT DET

TV BLOCK DIAGRAM

MOTOR+12V

SOUND +B

D1705, D1706,D1710, D1711

DEGAUSS_H

Q1705, Q1706

SWITCHING

V801CRT

V.OUTPUT ICIC401 LA78040

H.DRIVE 2

FL OUT

RED AMP

Q802, Q803

GREEN AMP

Q804, Q805,

BLUE AMP

Q806, Q807

SOUND AMP

REGULATORRELAYDRIVER

P.CON+5V

CP602B

TV_POWER_H

H_VOLT_SW

CUT OFF

CLAMP OFF

FEED BACK SWITCHING

IC1702KIA431A-AT

1 3 10

UNREG+8V

UNREG+5V

H_VOLT_SW

EMERGENCY

+B DOWN

E-21 E-22

VMC319A

105157

IC2601

05 R2622

HS2301

R2327 C2309

R2326C23

07 R2322

IC4003

C4095C4039

C8506 C8509

02R4017

33 C40

R4012 R4042

21 R40

26 R4027

IC4001

R8509R8508R8507

36 R4016 R4045

R8518 R8519 R8520L

C8521_1

C8517_1

C8513_1

C8514_1

C8519_1

C2641_1

C2640_1

C2608_1

C2646_1

C2643_1

C2644_1

C4084_1

C4011_1

C4069_1

C4070_1

C4068_1

C4071_1

C4067_1

C4009_1

C4051_1 C4052_1

C4063_1

C4078_1C4083_1

IC4007

VMC319A

PRINTED CIRCUIT BOARDS

DVD (TOP SIDE) DVD (BOTTOM SIDE)

F-1 F-2

TO DVD DECK

.J4202

VR1701

TU001C

4206_1

C4212_1

C8094_1

TP4201

C326_1

C323_1

L301_1

C311_1C

C305_1

C329_1 C

C308_2

C306_1

R356HS351

D1707C

1728_1

L5502_1

C5545_1

C5515 C

5519 C5543

C5542_2

C5540_1

C5555_2

SW2201

C4565_1

C4564_1

C4523_1

C4544_1

C4539_1

C4532_1

W143 C4506_1

C1534_1

C5505_1

C5525_1

C5520_1

C5524_1

W241W242

C8001_1

C8006_1

L8001W

C8007_1

C8009_1

CP2201

C5526_1

L4509_1

J2202J2203

W319 W

316 W314

W303 R153

W247W248

W228W229W230

CP8001

W237W239

C122_1

C119_1

C113_1

R4563 D5502

R114 R

X601W282

W136W856

CP8002

IC1701

C1713_1

R1722R1731

HS1701

C1707_1

FH1702

CD1703

CD1704

C4205_1

C4204_1

W049W050

W096 W

W293 W

R627 W046

W173 L1505

C104_1

W213W214

CP4503

D601 D

IC3001

IC3002R3009

IC3003 D3004

IC3004

CP1702

D1703 D1716

D1726R1710

L602_1

IC1702

C3002_1

CD1702

L1502_1

C3004_1

C331_1

C328_1

6.3A125V

PRINTED CIRCUIT BOARDSVCR (INSERTED PARTS)

SOLDER SIDE

F-3 F-4

Q4211Q4210

22_1C55

63 R55

IC4501

49 R45

55 Q4509

R4553 Q4511

51R4540R4536

IC8004 C80

8020 R

Q2201 Q2203

IC8002

IC1504

10 C15

IC1501

R116R115

IC1502

15Q4202

R4214 Q4201

08 R4212

Q601_1

IC1505

IC8001

01W346W347

Q605W81

PRINTED CIRCUIT BOARDSVCR (CHIP MOUNTED PARTS)

SOLDER SIDE

F-5 F-6

TO DVD DECK

TO VCR DECK

C408_1

T401_1

C405_1

Q401 R423

R421_1

R432R428

R443 C429

CP602B

CP802A

CD2251

Q408D418

D410 D408

W002D411

D403W812

C406_1

L804_1

PRINTED CIRCUIT BOARDS

DEFLECTION/CRT/OPERATION(SOLDER SIDE)

S1002XS1003X

S1005XS1004XS1001X

RELAY (INSERTED PARTS) SOLDER SIDE

RELAY (CHIP MOUNTED PARTS) SOLDER SIDE

SW SOLDER SIDE

S1005YS1004Y

F-7 F-8

A B C D E F G H

IC4001ZR36762

MPEG/MICON/DSP IC

101102103104

157158159160161162163164165166167168169170171172173174175176177178179180181182183184185186187188189190191192193194195196197198199200201202203204205206207208

53 54 55 56 57 58 59

60 61 62 63 64 65 66 67 68 69

70 71 72 73 74 75 76 77 78 79

80 81 82 83 84 85 86 87 88 89

90 91 92 93 94 95 96 97 98 99

MCL4148

22P CH

0.01 B

C40880.01 B

0.01 B

C4016 0.1 F

C4017 0.1 F

C4014 0.1 F

C4030 0.1 F

C4031 0.01 B

C4026 0.1 F

C4028 0.1 F

C4013 0.1 F

C4010 0.1 F

C4008 0.1 F

C4029 0.1 F

C4033 0.1 F

C4081 0.1 F

C4032 0.001 B

C4096 0.001 B

0.01 B

C4027 0.1 F

R4014 4.7K

R4005 75 +-1%

R4003 75 +-1%

R4004 75 +-1%

R4002 75 +-1%

R40244.7K

R4020 33R4019 33

R4021 33

R4025 220

R4026 100R4027 100

R4058 47

R4047 4.7K

R4035 4.7K

R4031 4.7K

W4BRH3.5X6X1.0X2

FCM2012H-102T04

W833W832

Q4004KTC3875S_Y_RTK

LEVEL CONVERT

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICENOTE:THIS SCHEMATIC DIAGRAM IS THE LATEST AT THE TIME

DURING PLAYBACK.MEASURED WITH THE DIGITAL TESTER

NOTE:THE DC VOLTAGE EACH PART WAS

TP4014

TP4010

TP4003

TP4005TP4006

TP4004

TP4012

TP4013

TP4007

TP4015TP4016

TP4009

TP4008

2.2uH0305

DIGITAL AUDIO SIGNAL(PB)

X4001100BT02701

IC4003 PQ070XZ01ZPREG+1.8V IC

1 2 3 4 56

5 6 7 8

CD4002CU2B3301

200/330mm

W5T29X7.5X19

LINK FN

DAC_VIDEO_CDAC_VIDEO_BDAC_VIDEO_DASDATA0ABCLKALRCLKDUPTD1AMCLKDUPRD1 MDMCDUPTD0MLV_GNDDUPRD0 RESETGNDP.CON+3.3VP.CON+5VP.CON+A5VP.CON+5VGND

SPDL_SENSTOUT_SWTIN_SW+1.8VRFA_SDEN+3.3V

D_GND RFA_DATAP.CON+3.3V RFA_SCLK

AAF_CEAAF_FE

HA0 DUPTD1 AAF_TEHA1 AAF_PIDUPRD1HA2 VR_SELHA3 FNNHA15 DUPTD0HA4 FNPHA5 HA16 DUPRD0 VBIASS0HA6 VBIASS1HA14HA7 DEFECTHA13 VR_SELHA8 LINKHA12 TRAY_OPENHA9 MIRR

HA10 HD15 TOUT_SW LDONHA11 SMUTEHA11 TRAY_CLOSEHA12 TRACK_DACHD7 TIN_SWHA13 FOCUS_DACSMUTEHA14 SPINDLE_PWMHA15 HA10 SLED_PWMHA16 HD14HA17 HA9HA18 P.CON+A5VHD6HA19 P.CON+3.3VHA20 HA8 RESET VCC+9V

HD0 P.CON+5VHD13HD1 ADCIN_7HD5HD2 ADCIN_6HA20 HOME HOMEHD3 ADCIN_5HD4 LDON

M_GNDHD5 HD12 D_GNDHD6 GNDWR DJTDO MLHD7 HD4 DJTDI MC DUPTD1HD8HD9 DJTMS MD

HD10 HD11 ICETCKHD11 HD3 ICETDOHD12 HA19 ICETDIHD13HD14 A_MUTE

HD15 I2CCLKHD10MEMCS0 HA18 I2CDAT

RDWR HD2 I2CDAT

HA17HD9 I2CCLK

SD_A0 HA7

SD_A1 HD1 P.CON+3.3VSD_A2 HA6SD_A3 HD8 IAMCLK AMCLKSD_A4 D_GNDSD_A5 HA5

SD_A6 IABCLK ABCLKSD_A7 HD0 IALRCLK ALRCLKSD_A8 HA4SD_A9 P.CON+5V

SD_A10 RD ASDATA0

SD_A11 HA3 ASDATA1SD_D0 HA2 ASDATA2 DUPRD1SD_D1 MEMCS0 SPDIFSD_D2SD_D3 HA1 M_GNDSD_D4 HA0SD_D5 VCC+9V

SD_D6 P.CON+A5VSD_D7SD_D8SD_D9 P.CON+3.3V

SD_D10SD_D11 P.CON+3.3VSD_D12SD_D13 GNDSD_D14SD_D15

RAMCS0# SPDIFRAMCS1#RAMRAS#RAMCAS#

SD_BA0RAMDQMRAMWE#RAMCLK

PCB130VMC319

FROM/TO AUDIO/VIDEO

3.2 0 3.33.2

SSCRXD

SPDIFAOUT(2)

AOUT(0)AOUT(1)

ABCLKGNDP-A2

AMCLKVDDP-A2

VDDPVID(7)

VID(3)VID(2)VID(1)VID(0)

GPCI/O(31)

RESET#

XOGCLKPGCLKA

VDDPGPCI/O(32)

GPCI/O(33)

GPCI/O(34)

GNDPDUPRD0DUPTD0VDD-IPDUPRD1DUPTD1

RAMADD(4)

RAMADD(3)

RAMADD(5)

RAMADD(2)

RAMDAT(14)

RAMDAT(1)

RAMDAT(15)

RAMDAT(0)

SPINDLEPULSE

SSCCLK

SSCTXD

SLEDPULSE 157

GNDDACD

CVBS/G/Y

CVBS/C

VDDDAC

MEMAD(5)MEMDA(8)MEMAD(6)MEMDA(1)MEMAD(7)MEMDA(9)MEMAD(17)MEMDA(2)GNDPMEMAD(18)MEMDA(10)

MEMAD(9)MEMDA(6)MEMAD(8)

MEMDA(5)

MEMDA(4)VDDC

MEMWR#MEMDA(12)VDDPMEMAD(20)

MEMDA(3)

GNDCMEMAD(19)

MEMAD(15)

MEMAD(14)MEMAD(13)MEMAD(12)MEMDA(15)MEMAD(11)

MEMAD(10)MEMDA(14)

MEMDA(0)VDDP

MEMAD(0)MEMAD(1)

MEMAD(2)MEMAD(3)

MEMAD(4)MEMRD#

GNDPVDD-IPVDDP VD

ICGPCI/O(0)IDGPCI/O(0)

ALRCLKGPAI/O

AINGNDC

VSYNCVDDC

HSYNCGNDP

IDGPCI/O(2)

ICGPCI/O(4)

ICGPCI/O(5)

IDGPCI/O(3)

MEMAD(16)

MEMCS(1)

MEMDA(7)

MEMDA(13)

MEMDA(11)

MEMCS(0)#

GPCI/O(20)

STBY-L

D1 1D1 2

BOOTSEL2 BOOTSEL1

01.21.93.33.3

FROM/TO MEMORY

P.CON+3.3V

P.CON+5V

P.CON+9V

GND(M)

(DVD PCB)

3.300001.600001.61.701.73.33.303.31.63.303.33.33.33.33.30003.33.33.3

03.31.80003.33.1003.303.305.03.33.35.13.3

3.2 0 0

1.9000

2.12.0

03.30.63.32.61.82.72.9

0.62.72.70.60.45.53.30.43.3

3.13.13.2

03.33.3

3.33.33.33.03.03.03.33.3

00.52.6

0000.9

0000.7

0003.3

FROM/TO RF AMP/DSP

3.3 3.3

MPEG/MICON SCHEMATIC DIAGRAM

SPDIF-134

(CP8001)

V_IN V_C V_OUT V_ADJ GND

NCNCNCGND

VCCWPSCLSDA

FROM/TO REGLATOR

A B C D E F G H

IC4007 SST39VF800-70-4C-EKFLASH IC 8M

242526

IC4005 M12L64164A-7T64M SDRAM IC

262728

0.1 FC4062

B4007FCM2012H-102T04

B4008FCM2012H-102T04

SD_A0SD_A1 HA16 HA15SD_A2SD_A3SD_A4 HA14SD_A5SD_A6SD_A7 HA13SD_A8SD_A9

SD_A10 HD15 HA12SD_A11 SD_D15 SD_D0

SD_D0SD_D1 HD7 HA11SD_D2SD_D3 SD_D14 SD_D1SD_D4 HD14 HA10SD_D5 SD_D13 SD_D2SD_D6SD_D7 HD6 HA9SD_D8SD_D9 SD_D12 SD_D3

SD_D10 HD13 HA8SD_D11 SD_D11 SD_D4SD_D12SD_D13 HD5 HA19SD_D14SD_D15 SD_D10 SD_D5

RAMCS0# HD12 HA20RAMCS1# SD_D9 SD_D6RAMRAS#RAMCAS# HD4 WR

SD_BA0RAMDQM SD_D8 SD_D7RAMWE# RESETRAMCLK

HA0HA1 HD11 RAMDQMHA2HA3 RAMDQM RAMWE#HA4 HD3HA5 RAMCLK RAMCAS#HA6HA7 HD10 HA19 RAMRAS#HA8HA9 RAMCS1#

HA10 HD2 HA18HA11 SD_A11 SD_BA0HA12HA13 HD9 HA17 SD_A9 RAMCS0#HA14HA15 SD_A8 SD_A10HA16 HD1 HA7HA17 SD_A7 SD_A0HA18HA19 HD8 HA6 SD_A6 SD_A1HA20

HD0 SD_A5 SD_A2HD1 HD0 HA5HD2 SD_A4 SD_A3HD3HD4 RD HA4HD5HD6HD7 HA3HD8HD9

HD10 MEMCS0 HA2HD11HD12HD13 HA0 HA1HD14HD15

MEMCS0RDWR

P.CON+3.3V

PCB130VMC319

MEMORY SCHEMATIC DIAGRAM(DVD PCB)

2.5 1.6

3.3WE#

A10/AP

FROM/TO MPEG/MICON

FROM AUDIO/VIDEO

A B C D E F G H

Q26012SA1036K

DVD LD CTL

Q26022SA1036K

CD LD CTL

1 10 11 12 13 14 15 16 17 18

20212223242526272829

30313233343536

4 5 6 7 8 9

IC2601ZR36708TQC

READ CHANNEL IC

17 18 19

20 21 22 23 24 25 26 27 28 29

30 31 32

50515253545556575859

6061626364

D2601KDS120RTK

CP2603A2001WR2-3P

Q26042SK3018

VR CD CTLS

Q26032SK3018

VR DVD CTL

Q26052SK3018

VR SEL CTL

CP2602IMSA-9615S-08C-PP

CD26022H080701

FFC(P=1.0mm)

CD26012H0O1901

FFC(P=0.5mm)

CP2601IMSA-9631S-24Y901

C26200.0056 BC26210.0056 BC26220.0056 BC2623

0.001 B

C2619560P CH

C26540.01 B

C2302 0.1 B

0.001 B

C26150.1 F

220P CH

470P CH

0.1 FC2648

C2303 0.1 BC2308

0.0022 B

33P CH

0.0022 B

0.0022 BC2604

0.0022 B

0.01 B

C2640_1

1006.3V KA

C2641_1

1006.3V KA

476.3V

R26124.7K

R26134.7K

R26114.7K

R2303 2.2

27K R2

100R2653

1.2KR2608

1.2K R2609

R26105.1K +-1%

1KR2618

R2304 2.2

1.2 1/2W

R260510K +-1%

4.7K R2627

B2601FCM2012H-102T04

FCM2012H-102T04

B2604FCM2012H-102T04

FCM2012H-102T04

TP12 TP11

5 6 7 8

SPDL_SENS

TOUT_SW

TIN_SWMOT_SPDL+RFA_SDENRFA_DATAMOT_SPDL- P.CON+5VRFA_SCLKAAF_CEAAF_FEAAF_TEAAF_PIVR_SELFNNTR-FNPTR+VBIASS0VBIASS1FO- FNNDEFECTFO+LINKFNPMIRRDVDPDLDONOPU_RFHOME

VR_DVD RF_GND GND

D_GND D_GNDDVDLD

P.CON+5VCDLDRF_A5V P.CON+A5VVR_CD

RF_GND RFA_SDENP.CON+3.3VCDPD

RFA_DATA

OPU_RF RFA_SCLKOPU_C

OPU_F SMUTEOPU_E

TRACK_DAC

FOCUS_DACOPU_VREF

SPINDLE_PWMAAF_CESLED_PWM

ADCIN_7OPU_D AAF_FE

ADCIN_5OPU_C AAF_TE

ADCIN_6P.CON+3.3VVCC+9VOPU_B AAF_PIM_GNDM_GND

VBIASS0

VBIASS1MOT_SLED-

DEFECTMOT_SLED+

MOT_SPDL-LINK

MOT_SPDL+

P.CON+9VLD

RF_GND SGND

TIN_SW

TOUT_SW

P.CON+3.3V

PCB130VMC319

0.9 1.6NCNCNC

16 CD_ACD

VC DVDL

RFACVP

1 DVDRFP

DVDRFN

33 LINK

SDEN48

MON(DVD)

NC(SW)

VOL(DVD)

GND(DVD)

LD(DVD)

LD(CD)

VOL(CD)

GND(CD)

MON(COM)

GND(PDIC)

GND(NC) NC

4.14.34.34.0NC

0.29.100 5.3 3.1 4.2 4.2 9.1 2.5 0 2.5 2.5

LIMIT SW

GND(D)

5.2 0.7 7.3 5.2

0 5.2 4.1 4.1

OUT1-IN1+IN1GND

VCCOUT2-IN2+IN20.7 0.5

0 00.7

3.02.52.52.62.53.300 2.5 2.5 2.5 5.02.6

4.53.9

(DVD PCB)

00002.33.53.52.62.45.14.34.33.13.101.5

2.6 02.6 5.1 5.1 3.7 5.1 0.2 0.2 0 3.3 2.7 2.2 2.3 2.9 0.2

FROM LODER

FROM/TO LODER

FROM/TO MPEG/MICON

RF AMP/DSP SCHEMATIC DIAGRAM

A B C D E F G H

10 11 12 13 14 15 16

2345678

CP8502IMSA-9604S-12Z13

AUDIO SIGNAL(PB)PLAYBACK VIDEO SIGNAL

R.SIGNALB.SIGNAL

Q8502KTA1504S_Y_RTK

VIDEO_BUFFER

Q8503KTA1504S_Y_RTK

VIDEO_BUFFER

Q8504KTA1504S_Y_RTK

VIDEO_BUFFER

CD85012H0C2204

FFC(1.25P)

12P CH

1 1025

C8514_1

4.750V KA

C8513_1

4.750V KA

FCM2012H-102T04 B8502

FCM2012H-102T04

1uH 0305

DIGITAL AUDIO SIGNAL(PB)

DAC_C[C]_VIDEO

DAC_B[Y]_VIDEO

P.CON+A5V P.CON+A5V DAC_D_DVD_VIDEO

DAC_VIDEO_CDAC_VIDEO_BDAC_VIDEO_D

P.CON+5VP.CON+3.3V

RESETMC DAC_VIDEO_C

AMCLKABCLK

ALRCLKASDATA0

DAC_VIDEO_B

DAC_VIDEO_D

DAC_D_DVD_VIDEO

DAC_C[C]_VIDEO

DAC_B[Y]_VIDEO

L_AUDIO

R_AUDIO

+ COMPONENT SIGNAL(U)+ COMPONENT SIGNAL(V)

PCB130VMC319

FROM/TO DVD IN/OUT

C(CVBS)

AUDIO-L

AUDIO-R

DVD RESET

1.40.6

1.61.11.63.34.92.5

3.3 0 0 3.3 1.7

CVBS CVBS

AUDIO/VIDEO SCHEMATIC DIAGRAM(DVD PCB)

FROM/TO MPEG/MICON

TO MEMORY

(CP8002)

A B C D E F G H

CP4503B2013H02-2P

CP4501TOC-C09X-A1

L45021626009

COIL,BIAS OSC

CP4502IMSA-9604S-06Z14

Q4503DTA124EKA

IC4501LA71205M-MPB

Y/C/AUDIO/HEAD AMP IC

1 10 11 12 13 14 15 16 17 18 192 20

414243444546474849

50515253545556575859

CAUTION: DIGITAL TRANSISTOR

S808X S808Y

Q45092SA1037AK

BUFFER

Q4505KTA1266

BIAS CTL

Q45112SA1037AK

BUFFER

4706.3V YK

C4532_1

3310V KA

C4523_1

2216V KA

2206.3V KA

0.3350V KA

C4514_1

0.047 B

C4522_1

0.047 B

0.068 B

0.01 B

820P CH

0.01 B

390P CHC4552

0.01 B

476.3V KA

150V KA

C4565_1

1025V KA

150V KA

476.3V KA

C4564_1

3310V KA

0.2250V KA

4.750V KA

10016V KA

R45371.8K 1/4W

82K 1/4W R4560

10 1/4W

W880W864

Q4501KTC3875S_Y_RTK

AUDIO PB SW

Q4502KTC3875S_Y_RTK

AUDIO PB SW

Q45062SC2412K

Q45072SC2412K

BUFFER

Q4504KTC3203_Y

BIAS OSC

L4509_1

100uH 9A06B

100uH 0305

P.CON+8VP.CON+5V_A

NORMAL_A

Y/C_AUDIO

HF2 Y/C_CLK

HF_COM Y/C_DATA

HF1 Y/C_CS

VIDEO_OUT

ENV_DET

VCR_A_MUTE

C_ROTARY

DUMMY_V.SYNC

V.REC_ST_H

H.AMP_SW1

Y/C_VIDEO

P.CON+5V_A

TUNER_VIDEO

V.SYNC

AUX_V[F/R]

DVD_VIDEO

Y/C_VIDEO

AUX_V[F/R]DUMMY_V.SYNC

TUNER_VIDEOP.CON+5V_A

P.CON+8V_BY/C_VIDEO

GNDVIDEO_OUT

NORMAL_AP.CON+8V

P.CON+5V_A

V.REC_ST_H

P.CON+8V_B

Y/C_AUDIO

PCB010VMC293

FROM/TO TV POWER

SP-CH1 (R)

SP-CH2 (L)

EP/LP-CH1 (R)

EP/LP-CH2 (L)

HF1 (R)

HF COM

HF2 (L)

SP COM

EP/LP COM

FROM/TO CYL

FROM/TO DIGITAL COMB FILTER

FROM DVD IN/OUT

FROM CHROMA/IF

FROM/TO MICON

FROM/TO HI-FI/DEMODULATOR

FROM REGULATOR1

Vref2.3V

HAPRE GND

REC:LP<EPPB:EP

PB,EEPB,EE

RECAMP MUTE

AUTOBIAS

LINEAMP

RECFM-EQ

VHS SOPBP R

PBFM EQ P RS-EQ

MAINDE-EM

LIMDOUBBLE FM

DEMSUBLPF

EMPHAFIL

MAIN 4.7K

V.SYNCSEP

6DBQV/QH

AGCTC2

BALTC1

VDD 4Fsc CLOCK

TIMMING OUT

DRIVER AUTO-BIAS

CLAMPCCD

VCAVCA

ALWAYS5V

BVX01 320FHVCO

PHASEEQ

fo-ADJ

PHASEEQ

FMAGCFIL Y-GND

FBC1/2

VIDEOAGC

Y/CMIXNC1

N.L.DEEM

CLAMPDETAILENH

NLEMPHA

NORMALR-EQTEST

YNR/COMB

3.58MBPF1

BGABGA

BEFORE

3.58MBPF2

B-UPAMP

MainCONV

ACCAMP

DETACC

4.21MBPF

SubCONV R

RECAFC

RECAPC

C-VCCSERAILDECODER

C-GNDC-ROTRF-SW

AUDIOMUTE

ENVDET

ACCDET

HA VCC

COMPOUT

KILLDET

DETCHROMA

2.2 2.2 2.3 2.2 2.2 2.5 2.3 2.2 2.3 2.4 5.0 1.0 1.0 1.7 1.4 0 1.5 0.1 2.2

0.82.205.05.02.33.33.34.02.61.95.04.84.84.80002.80.5

FE HEAD(GND)

FE HEAD(HOT)

TO FULL ERASE HEAD

AE HEAD(+)

AE HEAD(-)

AUDIO REC

AUDIO PB

FROM/TO HEAD AUDIO CONTROL

(VCR PCB)Y/C/AUDIO/HEAD AMP SCHEMATIC DIAGRAM

A B C D E F G H

MTZJ15B

Q102DTC124EKA

CENT LED SW

Q110DTC114EKA

Q106DTC124EKA

Q103ST-304L

EOT SENSOR

Q101ST-304L

BOT SENSOR

Q108RPI-303

REEL SENSOR

Q107RPI-303

REEL SENSOR

34Q104

RPI-352C40N

MS_SEN B1

Q105RPI-352C40N

MS_SEN A

LSA-1144EAU

TAB SW

IC101OEC8076A

SYSCON/TIMER/SERVO IC

26272829

30313233343536373839

40414243444546474849

6869 7

76 77 78 79

80 81 82 83 84 85 86 87 88 89

90 91 92 93 94 95 96 97 98 99

CP101TMC-J12P-B2

Q1142SA1037AK

BUFFER

C141 470

1SS133

0.01 BC111 0.1

0.0047 B

0.0039 B

68P CH

C156 1

0.0022 B

0.01 B

C113_1

1025V KA

C119_1

1025V KA

C103 47

10010V KA

C122_1

3310V KA

C102 10

C146 22

22016V YK

R164 4.7K

2.7K R160 4.7K

2.2M 1/4W

R124 10

R135 10

R103 27

1K 1/4W

4.7KR140

R139 10K

2.7K R159 4.7K

1K 1/2W

TP102H.SW

Q1162SC2412K

Q1122SC2412K

5 6 7 8

BACKUP+5V

BACKUP+5V SDA

VCR_POWER_H

AT+12VP.CON+5V_CP.CON+5V_A

Y/C_VIDEOTXY/C_CLKRXY/C_DATA RESET

Y/C_CS DVD_RESETDUMMY_V.SYNCH.SW AV_SW1

VIDEO_OUT H.SW

ENV_DET VCR_A_MUTE IIC_OFFVCR_A_MUTE

KEY_BCTL+ CAP_LIMIT

CTL- KEY_ATV_POWER_H TV_A_MUTEC_ROTARY REC_LED

DUMMY_V.SYNC T-REC_LEDV.REC_ST_H

REMOCON_INCYL_DRIVE SCLH.AMP_SW1

EXT_A_MUTECOMP OSD_Y SDA

VCR_A_MUTEDEGAUSS_H TX EXT_MUTE

TV_POWER_HOSDR RX

OSDB Y/C_DATA

OSD_RCAP_F/R Y/C_CS

OSD_GCYL_FG/PG Y/C_CLKOSD_B

H_CONTROL OSD_Y

TV_POWER_HEXT_A_MUTE

V.SYNCEOT

H_CONTROLBOTH.SYNCAV_SW1

SDAEXT_MUTE

SCLREMOCON_INVCR_POWER_H

REEL-S PROTECT

IIC_OFFREEL-T

EMERGENCYCTL+CENT_LED_CTL

TAB_SW CTL-

V.REC_ST_H

HIFI_ENVAT+5V

HIFI_H.SW

VCR_A_MUTE

SDAPOWER_FAILSCL

ST_SELECT

TV_POWER_H

TV_A_MUTECAP_F/R

BACKUP+5V OSD_RSCLCAP_LIMIT

MOTOR_GND

TV_POWER_H

AV_SW1AT+5VCONTROL_INOSD_BLDM_CTL

AV_SW2CYL_FG/PG SDA

SCLCYL_DRIVE

GNDDEGAUSS_HPOWER_FAILMOTOR_GND

PCB010VMC293

FROM/TO DVD IN/OUT

FROM/TO IN/OUT

FROM/TO CHROMA/IF

FROM/TO SOUND AMP/SURROUND

FROM/TO TV POWER

FROM/TO Y/C/AUDIO/HEAD AMP

FROM/TO REGULATOR1

0.9 1.4

5.1 GNDIN

A2 A1 A0

TEST VC

4.8 4.8 0 5.0

2.5 0 2.6 0.1 5.1 5.1 4.9 4.9 0 2.6 2.4 0 3.4 3.6 0 0 5.0 0 0.1 0 0 4.9 03.50

3.505.05.0002.7NC NC

3.6 3.64.95.00001.03.35.0004.94.7001.62.2

POWER_FAILREC/

CTL(+)

CTL(-)

CAP_F/R

CYL_SPEED_UP

REEL-S

REEL-T

DEGAUSS

TV_POWER_ON-H

VDD251:

VCR.A.MUTE

TV_MUTE

CAP_LIMIT

IIC_OFF

FSCLPF

AFCLPF

52: AFCC

REMOCON IN

VSSXIXOSXI

CYL_FG/PG

25:RESET

24:DUMMY.V.SYNC

EXT_A_MUTE

AV_SW1

RENT_H

EXT_MUTE

FF/REW_L

Y/C_CLK

Y/C_CS

Y/C_DATA

TV/DVD_LED

98:C_ROTARY99:H.AMP.SW1

100:COMP

TUNER_H

NCNCNCNC

NCNCNC NC

VM_OSD_SW

5.1 4.4

NC NC00

5.2 5.1 0

CAP CTL

LDM CTL

CAP VCO

CAP.M F/R

MOTOR GND

CYL FG/PG

CYL CTL

CAP FG

I LIMIT

LD/CY VCO

FROM/TO CAPSTAN DD UNIT

2.4 1.2

0.9 5.1

0.5 1.4

(VCR PCB)MICON SCHEMATIC DIAGRAM

A B C D E F G H

H1H1 H2

MSP-213V1-432_NI_LF

REAR OUT JAK

1SS133

H1NCH1H2

J4201MSP-213V2-432_NI_LF

REAR IN JACK

2 3H NC

J8007MSP-251V-05PBSN

COAXIAL

J2201MSJ-2000_AG

HEADPHONE_JACK

12 3 4 567

:SINCE THESE PARTS MARKED BYCAUTIONDESCRIBED IN PARTS LIST ONLYCRITICAL FOR SAFETY,USE ONES

DANS LA NOMENCLATURE DES PIECESN’UTILISER QUE CELLS DECRITESDANGEREUSES AN POINT DE VUE SECURITE

:LES PIECES REPAREES PAR UN ETANTATTENTION

OS2201RPM7138-WH10

MTZJ5.6B

MTZJ6.8B

Q2203DTC114EKA

T-REC LED SW

Q2201DTC114EKA

REC LED SW

Q2202DTC114EKA

POWER_LED_SW

Q4204DTC124EKA

ZERO_SW

CP2201A2001WV2-2P

Q4202DTA124EKA

MUTE SW

Q42102SA1037AK

MUTE SW

Q42122SA1037AK

BUFFER

47016V YK

C8094_1

10010V YK

1SS133

CHC221

470P CH

470P B

0.022 B

100P CH

C4206_1

1025V KA

C4212_1

1025V KA

C4205_1

1025V KA

C4204_1

1025V KA

220 1/4W

4.7K 1/4W

330 1/4W

W4BRH3.5X6X1.0X2

Q80022SC2412K

D AUDIO DRIVER

Q42032SC2412K

MUTE SW

Q42012SC2412K

MUTE SW

Q42112SC2412K

CH MUTE

SOUND_R+

SOUND_L+

SP_OUT_R

SP_OUT_L

REC_LED

T-REC_LED

TV_POWER_H

P.CON+5V

P.CON+8V

REC_LED

T-REC_LED

REMOCON_IN

EXT_A_MUTE

VCR_A_MUTE

EXT_MUTE

TV_POWER_H

REAR_V_IN

FRONT_V_IN

JACK_OUT

P.CON+5V_E

EXT_A_MUTEFRONT_A_IN_R

FRONT_A_IN_L

VCR_A_MUTEREAR_A_IN_R

REAR_A_IN_L

SW_AUDIO_OUT_RSW_AUDIO_OUT_L

P.CON+5V_EZERO

SPDIF-134

SOUND_GNDGND

FROM CRT

(CD2251)

FROM/TO SOUND AMP/SURROUND

FROM REGULATOR1

FROM/TO MICON

TO HI-FI/DEMODULATOR

FROM DVD IN/OUT NC

PCB010

8.98.1

YELLOW REDWHITE

0.15.2

5.25.2

VMC293

IN/OUT SCHEMATIC DIAGRAM(VCR PCB)

FROM/TO TV POWER

A B C D E F G H

CP601A2001WR2-4P

IS NON POLAR ONE.THE ALUMI ELECTROLYTIC CAPACITOR MARKED NPTHE RESISTOR MARKED F IS FUSE RESISTOR.NOTE:

W5T29X7.5X19

L603W5T29X7.5X19

IC602KIA78L10F-RTF

10V_REG IC

MTZJ12B

Q601_1DTC114EK

BUFFER

CP602B2013H02-9P

Q605DTA114EKA

LA76319M-MPB-E

CHROMA/IF_IC

1 10 11 12 13 14 15 16

33343536373839

404142434445464748

CP603B2013H02-8P

CD602CU291701

CD603CU284501

0.015 B

0.33 B

0.01 B

0.47 B

1 BC603

C609 10

C612 10

C624 22

R603 100

27K 1/4W

330 1/4W

R626 22K

100 1/2W

4.7K +-1%

4.7K 1/4W

3.3K 1/4W

390 1/4W

1K 1/4W

Q6062SC2412K

Q6022SC2412K

PROTECT

L601 100uH 0305

P.CON+5V

P.CON+8V

AT5.7VREG

8.5VREG

P.CON+5V_C

Y/C_VIDEO-Y

COMB_FSC

DVD_Y/C-Y

V.SYNC

V.OUTSDA DVD_Y/C-YTV_POWER_H

H.OUTOSD_YP.CON+5V

EMERGENCY OSD_B

OSD_G AFC

H.OUTOSD_R

H.SYNC

V.SYNC P.CON+8V

VCR_POWER_H H_CONTROL

SCL TV_POWER_HSDA

IIC_OFF

MOTOR+12V

MOTOR_GND

P.CON+5V_BP.CON+8V

8.5VREG

P.CON+5V_B

PROTECT ACLEMERGENCY Y/C_VIDEO-Y

V.SYNC MOTOR+12V

H.SYNC AT5.7VREG

VCR_POWER_H

IIC_OFF

H_CONTROL

TV_POWER_H

CHROMA/IF SCHEMATIC DIAGRAM (VCR PCB)

PCB010VMC293

FROM TV POWER

4.45.0

FROM DVD IN/OUT

TO Y/C/AUDIO/HEAD AMP

FROM/TO MICON

FROM/TO REGULATOR1

NCNC4.9NCNC

(CP603B)

FROM/TO CRT

CLAMP_OFF

CUT_OFF

VIDEOSW

LPF ATT

REG-SW

CLSHARP

COLOPCLAMPMATRIX

OSDCONTRAST

CEMOBPF YC SN ACC

VERRAMP

VERC/D

VERSEP

HORVCC

HOROUT

PHASESHIFTER

AFSW X-RAY

HORVCO

HORC/D

1/256BUS

ORIVE/OUT-OFF

RST 5V/8V-REG

AUDIOSW

ABL/ACL

DC REST CONTRASTBRIGHT

SYNCSEP

+B_DOWN

EMERGENCY

P.CON+5V

TV_POWER_H

8.6 2.5 2.5 4.3 8.5 2.6 7.8 3.4 3.4

2.20 0 5.2 3.4 3.5

2.73.53.15.0NCNC 2.6 NC3.63.94.32.52.64.80000

10.0 0 12.0

IIC_OFF

FROM/TO DEFLECTION

NC NC NC

(CP602B)

OUT GND IN

TEST POINT

A B C D E F G H

C331_1

1016V KANP

HS351763WAA0255

SPEAKER

SP352SG04H02BRA8 OHM

SPEAKER

SP351SG04H02BRA8 OHM

CD303CU149001

IC352 AN7522NSOUND AMP IC

1 10 11 122 3 4 5 6 7 8 9

1 10 11 12 13 14 15 16

171819

20212223242526272829

303132

4 5 6 7 8 9

CP303A2502WV2-4P

470P B

0.0056 BC302

0.0056 B

470P B

0.033BC3

C350 22

220025V YK

_1 1025

C315 1

_1 1025

C357 22

100 1/4W

56K 1/4WR359

47K 1/4W

100K 1/4W

Q3502SC2412K

MUTE SW

L301_1

100uH 9A06B

SOUND_R+

SOUND_L+

SP_OUT_RSOUND+BSP_OUT_L

SOUND_GND

TV_POWER_H

TV_A_MUTE

SW_AUDIO_OUT_L

SW_AUDIO_OUT_R

P.CON+8V

PCB010VMC293

FROM/TO IN/OUT

FROM REGULATOR1

FROM DVD IN/OUT

FROM/TO MICON

FROM TV POWER

(VCR PCB)SOUND AMP/SURROUND SCHEMATIC DIAGRAM

L R-+ - +

SOUND R+

SOUND L+

SOUND L-

SOUND R-

controlMODE

R IN VrefVCC

PF1 AGC L IN

SURRAGC +

L ONTVDBDLBLTGNDPF4PF3PF2NCNC

SCLSDAR OUT

NCTDBLD

Balance/MUTEControl

Volume 2.2K

RTRBBBNCNC

Control

6.6 3.5 0 3.5 1.33.9 0 1.3 6.6 3.5 0 3.5

NC NC NC

NC4.2 1.9 4.6 0 0 4.1 4.2 4.2 0 4.4 4.0 0 0

NC2.3 4.0 4.5

2.5 7.8 4.6 3.9 NC0 0 3.9 4.0 4.2 3.4 2.3 0 0 4.5 5.02 5.02

A B C D E F G H

IC5501AN3663FBP

HI-FI/AUDIO/HEAD AMP/DEM IC

1 10 11 12 13 14 15 16

33343536373839

404142434445464748

C5559476.3V KA

1050V YK

0.2250V YK

2235V YK

2.250V YK

C5505_1

4716V KA

2235V YK

1SS133

11EQS04N

C5557 0.1 B

C5549 0.1 F

C5556 0.01 B

0.015 B

0.047 B

0.01 F

C5553 0.015 B

C5552 0.1 B

82P CH

C556682P CH

C5558 0.01 F

C5555_2

1025V KA

C5554 1050V YK

0.2250V YK

4716V YK

0_1 33

YK C553

1.2K 1/4W

TP5501HIFI ENV.

L5502_1

22uH 0305

22uH0305

FRONT_A_IN_R

FRONT_A_IN_L

REAR_A_IN_R

REAR_A_IN_L

TUNER_AUDIO

P.CON+5V_A

V.REC_ST_H

AUDIO_OUT_R HIFI_ENV

HIFI_H.SW

ST_SELECT P.CON+5V_A

AUDIO_OUT_L HF2

P.CON+12V

HF_COM

FSCNORMAL_AY/C_AUDIO

NORMAL_AY/C_AUDIO

P.CON+5V_A

P.CON+12V

V.REC_ST_H

HIFI_ENV

HIFI_H.SW

VCR_A_MUTE

ST_SELECT

DVD_A_OUT_L

DVD_A_OUT_R

AUDIO_OUT_L

AUDIO_OUT_R

FROM IN/OUT

FROM DIGITAL COMB FILTER

FROM REGULATOR1

FROM/TO MICON

FROM/TO DVD IN/OUT

FROM/TO TV POWER

2.41.604.94.72.30

2.40.7

4.5MTRAP

CUEBPF

AMDEMOD

95HMzBPF

SUBBPF

SUB DET

3.5MVCO

DEM_BLK

FMDEMOD

OUTPUT SW

SUB DEEN MATRIX

LOGAMP

INPUT_SW(R)

INPUT_SW(L)

MAINDEEN

MUTE VCO-F0ADJ

ZZ-PROM

COMPPNR RCH

SW NOISE

LCH BPF

RCH BPF

PC PB LPF

PB LPF

AUDIO LIMIT

PNR LCH

SW NOISE

RCHVCO

REC LPF

LCH VCO

REC LPF

NOISEDET

SW4SW2

SW22 LMIX

LINERSW

HOLD TIMING

AMPCURR

FROM 1PIN

FROM 3PIN

MIXHIFI

AN3672FBPJ

0 2.3 02.3 2.2 2.4 2.1 0.5 0 0 0 2.0 2.2 0 0 2.4

0004.72.13.52.2

(VCR PCB)

HIFI/DEMODULATOR SCHEMATIC DIAGRAM

PCB010VMC293

A B C D E F G H

TU001 115-V-K015AR_BMONITOR TUNER

11011121314151617

3456789

IC1505 MM1504XNREVIDEO OUT SW IC

IC1502 MM1501XNREAV SW IC

IC1504 MM1501XNREAV SW IC

3.350V KANP

L1502_1

10111213141516

2 3 4 5 6 7 8

4716V KA

47P CH

0.01 B

0.47 B

10006.3V YK

4706.3V YK

C1534_1

1025V KA

1K R151

Q15012SC2412K

BUFFER

Q1502KTC3875S_Y_RTK

BUFFER

Q1503KTC3875S_Y_RTK

BUFFER

P.CON+5V

TUNER_AUDIO

COMB_FSC

Y/C_VIDEO

Y/C_VIDEO-Y

COMB_FSC

Y/C_VIDEO

AUX_V[F/R]

TUNER_VIDEO

P.CON+8V_B

GNDY/C_VIDEO-Y

AV_SW1

DVD_Y/C-CP.CON+8VDVD_VIDEO

DVD_Y/C-C

AV_SW2

AV_SW1

AV_SW2

SDAP.CON+12VSCL

AT+30VP.CON+5VFRONT_V_IN

P.CON+12VP.CON+8V

REAR_V_IN

FRONT_V_IN

JACK_OUT

PCB010VMC293

FROM/TO CHROMA/IF

FROM/TO TV POWER

FROM DVD IN/OUT

FROM/TO MICON

FROM REGULATOR1

FROM/TO IN/OUT

(VCR PCB)

DIGITAL COMB FILTER SCHEMATIC DIAGRAM

AVSS DD

AV Y C DV

OUT SS

2.4 3.0 2.6 2.6

2.2 2.5

VccVin2

5.4 3.8 1.4 4.2 3.6 0

5.5000

TO DVD DECK

+BNC NC NC NC NC NC NCNCNC AUDI

NCNCNCNCNC0

31.5 0 0 2.1

4.2 0 0 0 0 0 0

NC 4.8

NC0 0NC

A B C D E F G H

IC8002 MM1501XNREAUDIO SW IC

IC8001 MM1501XNREAUDIO SW IC

2.250V NA

Q8007DTC124EKA

ZERO MUTE SW

S801YS801X

CP8002IMSA-9604S-12Z14

0.01 B

56P CH

820P CH

100P CH

2216V KA

C8001_1

1025V KA

C8009_1

1025V KA

2216V KA

100K 1/4W

10 1/4WR8054

4.7K 1/4W

Q80062SC2412K

ZERO MUTE SW

100uH 0305

IC8004NJM4580M(TE1)

MIXER IC

5 6 7 8

CP8001A2001WV2-11P

SW_AUDIO_OUT_L

SW_AUDIO_OUT_RAV_SW1

TXAUDIO_OUT_L

P.CON+9V_DH

P.CON+5V_D

P.CON+3.3V

SW_AUDIO_OUT_L

SW_AUDIO_OUT_RSPDIF-134

SPDIF-134SW_AUDIO_OUT_L

P.CON+5V_EP.CON+12V

DVD_Y/C-C

DVD_VIDEO

AUDIO_OUT_R

DVD_Y/C-YAV_SW1

SW_AUDIO_OUT_R

P.CON+12VTX

DVD_RESET

AV_SW1

DVD_VIDEO

DVD_Y/C-C

DVD_Y/C-YGND

P.CON+5V_E

DVD_RESET P.CON+3.3V

P.CON+5V_D

P.CON+12V

P.CON+9V_DH

AT+5VDVD_A_OUT_L

DVD_A_OUT_R

P.CON+12V

DVD_VIDEO

DVD_A_OUT_L

DVD_A_OUT_R

AUDIO_OUT_L

AUDIO_OUT_R

PCB010VMC293

FROM REGULATOR1

(VCR PCB)DVD IN/OUT SCHEMATIC DIAGRAM

(CD8505)

FROM/TO REGULATOR2TO SOUND AMP/SURROUND

TO IN/OUT

TO DIGITAL COMB FILTER

TO CHROMA/IF

FROM MICON

FROM/TO TV POWER

(CP8502)

FROM/TO AUDIO/VIDEO

0 6.1 6.1 6.1

6.1 6.1 6.1 12.3

0.7 0.70

P.CON+D5V

SPDIF-134

P.CON+3.3V

P.CON+9V

P.CON+3.3V

C(CVBS)

AUDIO-L

AUDIO-R

DVD RESET

A B C D E F G H

10uHTSL0808

IC3003KIA278R05PI

P.CON+5V_A OUT IC

1 2 3 4

IC3001 KIA278R05PIP.CON+5V_D OUT IC

1 2 3 4

IC3002 KIA278R09PIP.CON+9V_D OUT IC

1 2 3 4

IC3004KIA278R05PI

P.CON+5V OUT IC

1 2 3 4

HS3001763WAA0184

Q3009DTC114EKA

Q3008DTA143EKA

Q3005KTB1366

3.3V OUT

Q3007KTA1281_Y

P.CON+12V SW

10V YK

11EQS04N

11E1-EIC

C3002_1

10010V YK

4706.3V YK

C3013150V KA

10R3008

2201/4W

3301/4W

1801/4W

56K 1/2W

100 1/4W

10 R302

100 1/4W

4.7KR3004

10K 1/4W

100 1/4W

Q3003KTC3209_Y

AT+5V OUT

Q3014KTC3209_Y

BACKUP+5V

Q30152SC2412K

BUFFER

Q30012SC2412K

BUFFER

Q30042SC2412K

3.3V CTL

Q30062SC2412K

3.3V CTL

Q3002KTC3209_Y

P.CON+8V SW

Q30112SC2412K

Q3010KTC3209_Y

P.CON+5V_C SW

P.CON+12V

MOTOR+12VUNREG+8VUNREG+5V

+BAT5.7VREG

P.CON+5V

P.CON+12V

P.CON+8VVCR_POWER_HAT+30V

P.CON+5V_AAT+12V

P.CON+8VP.CON+5V_A

UNREG+5V

BACKUP+5V

P.CON+8V

VCR_POWER_H8.5VREG

AT+12VP.CON+5V_CDVD_H

BACKUP+5V

P.CON+5V_A

P.CON+5V

P.CON+8VP.CON+9V_DH

P.CON+5V_D

P.CON+8V

P.CON+5V

P.CON+3.3V8.5VREGAT5.7VREG

P.CON+8VDVD_H

P.CON+5V

P.CON+5V_C

P.CON+5V

P.CON+5V_A

P.CON+12V

VCR_POWER_H+BAT+5V

P.CON+12V

P.CON+3.3V

P.CON+5V_D

P.CON+9V_DHP.CON+5V_C

P.CON+12V

AT+30V

PCB010VMC293

REGULATOR1 SCHEMATIC DIAGRAM

5.0 3.3

FROM/TO TV POWER

TO DIGITAL COMB FILTER

FROM/TO MICON

TO SOUND AMP/SURROUND

FROM/TO CHROMA/IF

TO DVD IN/OUT

TO IN/OUT

IN OUT GND SW

IN OUT GND SWIN OUT GND SW

5.05.0

8.0 5.0 0 5.0 8.0 5.0 0 5.0 12.0 9.0 0 5.0

7.5 5.0 0 5.0

12.0 7.8

4.03.6

5.0 5.0

(VCR PCB)

GND SWIN OUT

A B C D E F G H

0.22 1W

CP1704A1561WV2-2P

CD1704

CD1703

TH1701ZPB45BL3R0A

IC1701PS2561L1-1-V(W)

FEED BACK

1.2 7W

F17016.3A125V6.3V125V

FH1702EYF-52BCY

FH1701EYF-52BCY

RY1701ALKS321

L17038R200024

DEGAUSS COIL

L17012R2A752F28

COIL,LINE FILTER

IS THE LIVE CONNECTIONCAUTION:

6.3A 125V

WHITEBLAD

CD17020R415906

AC120V_60Hz T17018142065S

N’UTILISER QUE DES FUSIBLE DE MEME TYPE

CAUTIONREPLACE ONLY WITH THE SAME TYPE FUSE

:FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,

:POUR UNE PROTECTION CONTINUE LES RISQUES D’INCEIEATTENTIONWAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST

NOTE:THE DC VOLTAGE AT EACH PART WAS MEASURED

330 2W

0.15 1W

HS1701763WAA0238

L1704W5T_20*10*10A

IC1702 KIA431A-AT

FEED BACKSWITCHING IC

MTZJ18B

MTZJ2.7B

Q17052SK3326(2)

SWITCHING

CP1702B2013H02-8P

CD604CU282401

1N4937

1SS133

FE201-6L49

21DQ09N

1SS133

1N4937

SB340L-6737

FE201-6L49

RGP15J

1SS133

1N4937

C1713_1

0.047100V MMTSC170

560P2KV R

0.0033500V B

0.0056 B

0.00222KV B

0.0033 B

0.01 B

1001/4W

680 1/4W

1K 1/4W

100 1/2W

1K 1/4W

W4BRH3.5X6X1.0

Q1702KTC3198

RELAY DRIVE

Q1706KTC3203_Y

SWITCHING

POWER_FAIL

DEGAUSS_H

MOTOR_GND

SOUND+B

SOUND_GND

MOTOR+12V

MOTOR_GND

SOUND_GND

UNREG+5V

MOTOR+12V

UNREG+8V

P.CON+12V

PCB010

(CP604)

TO DEFLECTION

FROM/TO Y/C/AUDIO/HAED AMP

FROM/TO DVD IN/OUT

FROM/TO REGULATOR1

FROM/TO IN/OUT

TO CHROMA/IF

TO SOUND AMP/SURROUND

FROM/TO MICON

10.7 9.7

16.3 1.5

2.5 0 4.0

168 6.5

(S811)

TV POWER SCHEMATIC DIAGRAM(VCR PCB)

P.CON+12V

H VOLT

VMC293

6.3A 125V

(F1701)

A B C D E F G H

ELH5L4113

IC401 LA78040V.OUTPUT IC

1 2 3 4 5 6 7

V801A51AKL13X04

T401_1ETH14Y47AY

15K +-1%

27K+-1%

TERHEA

FB401_1 FJN20A003

CP404A1561WV2-A5P

CP802AB2013H02-5P

CD805CU823001

CD803CU823001

R4403.3K 10W C1

R4302.710W C 1 2

CD808CH011202

CD807CH012801

WAS RECEIVED IN GOOD CONDITION AND PICTURE IS NORMAL.WITH THE DIGITAL TESTER WHEN THE COLOR BROADCAST

0.47 2W

180 2W

CP001003P-2100

C406_1

2.250V KANP

HS401763WAA0212

HS402763WAA0181

MTZJ5.6B

Q407KRC102MAT

H.VOLT_SW

CP602BA2001WV2-9P

Q4062SA1624

CURRENTDET.

Q4092SA1624

H.VOLT_SW

CP604A2001WV2-8P

C403 22

C407 22

AU02A-EIC

1N4005-EIC

AU02A-EIC

1SS133

_1 0.01

0.0022500V B

0.1100V MKT

0.0012KV R

C423 22P

0V MHE

100035V MHE

47160V BXA

22250V MHE

2.2100V YK

8.2K 1/4W

68K 1/2W

47K 1/4W

R419 15

2.7K 1/4W

12K 1/2W

R441 10

42 15K

47K 1/4W

B403W5RH3.5X5X1.0

B401W5RH3.5X5X1.0

Q4032SD2499(LBOEC1)

FL OUT

Q401KTC3227_Y

H.DRIVE

Q408KTC3207

P.CON+5V

HEATER

TMC564PCB080

(CP1702)

(CP602)

FROM/TO CHROMA/IF

(CD002)

TO CRT

(CP802B)

(CP803)(CP805)

TO CRT

HEATER

THERMAL PROTECTION

VCC GNDPUMP UP

0115.0

P.CON+5V

EMERGENCY

+B_DOWN

TV_POWER_H

AFCACL

TO DVD DECK

TO VCR DECK

H.VOLT

FROM/TO TV POWER

DEFLECTION SCHEMATIC DIAGRAM

12.0 12.0

(DEFLECTION PCB)

4.0 2.0 0 12.025.0 4.0

SCREEN

FORCUS

FROM/TO DY

A B C D E F G H

J801ISHS62S

CRT SOCKET

CC8018990TPA002

BT002R03(AB)E_2P_G

BT001R03(AB)E_2P_G TM101

ORV201N36010 BL001HPN-01

CP802BB2013H02-5P

15K 2W

:LES PIECES REPAREES PAR UN ETANTATTENTIONCD2251CU220701

1 2 CP80

CP603BA2001WV2-8P1

1SS133

560P CH

680P CH

100P B

100P CH

C819 1

1.8K 1/4W

1K 1/4W

820 1/4W

560 1/4W

3.3K 1/4W

4.7K 1/4W

15K 1/4W

1.8K 1/4W

220 1/4W

1.8K 1/4W

56 1/4W

1.8K 1/4W

2.7K 1/4W

Q8022SC4217

RED AMP

Q803KTC3199_Y

RED AMP

Q807KTC3199_Y

BLUE AMP

Q8042SC4217

GREEN AMP

Q8062SC4217

BLUE AMP

Q805KTC3199_Y

GREEN AMP

L804_1

100uH 9A06B

HEATER

(CP802A)

FROM DEFLECTION

EN(CP2201)

TO IN/OUT

KEY-BPCB270

CRT BLOCK

7.87.3

7.33.0

HEATER

121.00

119.00

TECB10

ACCESSORY

PCB110TCC426

(OPERATION PCB)

CRT/OPERATION SCHEMATIC DIAGRAM (CRT PCB)

FROM/TO CROMA/IF

CLAMP_OFF

CUT OFF

(CP603)

A B C D E F G H

M2002BCD3B02

M2001JCL9B61

D1SG-107F6

R2 82K

R1 560

S1002X

S1001X

S1004X

S1003X

S1005X

S1002Y

S1001Y

S1004Y

S1003Y

S1005Y

SW1AB-271-10ACP1

IMSA-9615S-08C-PP

RELAY/SW/FG SCHEMATIC DIAGRAM

(RELAY PCB)

(SW PCB)

SP.MTR(+)

SLD.MTR(-)

SLD.MTR(+)

SP.MTR(-)

BEC001PCB640

BEC002PCB68A

A B C D E F G H

CP602B

CP4501

21CP80

7654321

4 3 2 14321

CP2603

CP2601

CP1702

CP2602

OF PRINTING AND SUBJECT TO CHANGE WITHOUT NOTICETHE TIMETHIS INTERCONNECTION DIAGRAM IS THE LATEST ATNOTE:

CP1704

CD1703

CD1704

L1703DEGAUSS COIL

WHITEBLAD

CD1702AC120V_60Hz

TU001MONITOR TUNER

4 3 2 1CD30

H1H1 H2

J4202REAR OUT JAK

H1 NC H1 H2

J4201REAR A/V JACK(STEREO)

EJ2203

FRONT AUDIO JACK

2 3H NC

EJ2202

FRONT VIDEO JACK

2 3HNC

EJ2204

FRONT AUDIO JACK

J8007COAXIAL

J2201HEADPHONE_JACK

1 2345 6 7

OS2201

CYLINDER UNIT ASS’Y

CD803CD805

12116 5 4

7 1CRT

TCC426

FFCCD603

CP603B

CUT_OFF

VM COIL

CLAMP_OFF

VM_OSD_Y

EW OUT EW OUT

P.CON+12V P.CON+12V

CAPSTAN DD UNIT ASS’Y

AUDIOOUT

OUTVIDEO

AT+30V

VM_OUT

VM_OSD_Y

CD2601

CD2602

CD4002

VMC319

CRT PCBPCB110

TM101COMMAND TRANSMITTER

CLAMP_OFF

CD602FFC

P.CON+5V

EMERGENCY

+B_DOWN

TV_POWER_H

AFCACL

H VOLT

P.CON+5V

EMERGENCY

+B_DOWN

TV_POWER_H

AFCACL

CD604FFC

H.VOLT

SCREEN

TMC564PCB080

TV MT PCB

VMC293

CP8001

CP8002CP8502

NC(SW)

MON(DVD)

AUDIO PB

AUDIO REC

REDYELLOW WHITE

SPDIF-134 SPDIF-134

GND(M)GND(M)

VCR MT PCB

DVD MT PCB

AFT OUT

SIF OUT

EP/LP_COM

SP_COM

HF_COM

HF1_(R)

SP-CH1 (R)

SP-CH2 (L)

EP/LP-CH1 (R)

EP/LP-CH2 (L)

HF2 (L)

CP4502

C(CVBS)

AUDIO-L

AUDIO-R

DVD RESET

P.CON+D5V

P.CON+3.3V

P.CON+9V

P.CON+3.3V

LD/CY VCO

I LIMIT

CAP FG

CYL CTL

CYL FG/PG

MOTOR GND

CAP.M F/R

CAP VCO

LDM CTL

CAP CTL

AE HEAD(-)

AE HEAD(+)

AUDIO PB

AUDIO REC

PCB130

GND(D)

AUDIO-R

CD8501FFC

C(CVBS)

DVD RESET

AUDIO-L

P.CON+3.3V

P.CON+5V

P.CON+9V

FG SENSER

SPINDLE MOTOR

SLED,LOADING MOTOR

GND(D)

LIMIT SW

VOL(DVD)

GND(DVD)

LD(DVD)

LD(CD)

VOL(CD)

GND(CD)

MON(COM)

GND(NC)

GND(PDIC)

MON(DVD)

NC(SW)

VOL(DVD)

GND(DVD)

LD(DVD)

LD(CD)

VOL(CD)

GND(CD)

MON(COM)

GND(NC)

GND(PDIC)

DRIVEDVD

OPTICAL PICK-UP

AE HEAD(+)

AE HEAD(-)

H5001HEAD AUDIO CONTROL ASS’Y

CONTROL

EP/LP HEAD

SP HEAD

HI-FI HEAD

UN4001

ROTORMAGNETCOIL

MAINHALLSENSOR

7654321FF

7654321

WHITERED

LOADING MOTOR

O GVCC

MRFG SENSOR

LOGICSWITCH

HALLVCCHALL

PCB010

INTERCONNECTION DIAGRAM

FULL ERASE HEAD ASS’Y

WAVEFORMSY/C/AUDIO/HEAD AMP

The following waveforms were measured at the point of the correspondingballoon number in the schematic diagram.

MPEG/MICON

100µs

500µs

MEMORY

RF AMP/DSP

AUDIO/VIDEO

WAVEFORMSMICON

CHROMA/IF

SOUND AMP/SURROUND

DEFLECTION

HI-FI/DEMODULATOR

DEFLECTION

DVD IN/OUT

DEFLECTION

WAVEFORMS

0.5µs

DIGITAL COMB FILTER

CRT/OPERATION

CHROMA/IF

MECHANICAL EXPLODED VIEW

PCB110(CRT PCB ASS'Y)

135202

101E212

101F212101K

101J101H

101O212

111150

207207

205210

208208

209209

PCB080(DEFLECTION PCB ASS'Y)

103103

104106

207207

121128

208134

PCB010(VCR PCB ASS'Y)

MECHANICAL EXPLODED VIEW

PCB270(OPERATION PCB ASS'Y)

121208

211208

133 208 121

214208

208137118

208208

215122

206206

206118

PCB130(DVD PCB ASS'Y)

MECHANICAL EXPLODED VIEW(PACKING DIAGRAM)

146, 147, 148, BL001, TM101

CHASSIS EXPLODED VIEW (TOP VIEW)

302312

UN4001

335342

322508

334333

346345

CD1501

CD1502

Applying positions AA for the grease are displayed for this section.Check if the correct grease is applied for each position.

NOTE:MARKCLASS

GREASE AA

CHASSIS EXPLODED VIEW (BOTTOM VIEW)

300303

329311

340509

CD1501

CD1502

NOTE:MARKCLASS

GREASE AA

DVD DECK EXPLODED VIEW

606613

617701

SW1CD2302

620609

PCB68A(RELAY PCB ASS'Y)

604 602

PCB640(SW PCB ASS'Y)

CD2001

CD2301

Do not replace the parts. Because, minute adjustments are needed if this condition is disassembled further more.If the repair is needed, replace the DVD MECHA ASS'Y.

NOTE:CLASS

GREASE

MECHANICAL REPLACEMENT PARTS LIST

Location No. TSB P/N Reference No. Description

101 AE003099 7A701A032A FRONT CABI ASS'Y101A AE003100 701WPJC516 CABINET,FRONT101B AE003101 711WPA0200 PLATE,FRONT101C AE003102 712WPJB973 FLAT,FLAP101D AE003103 712WPJB987 FLAP,DVD101E AE003104 713WPA0311 GLASS,LED101F AE003105 713WPA0312 GUIDE,REMOCON101G AD302008 7235490036 BADGE,BRAND101H AE003106 735WPA0805 STOPPER,BUTTON101I AE003107 735WPA0808 BUTTON,FRAME-DVD101J AE003108 735WPA0809 BUTTON,FRAME-VCR101K AE003109 735WPEA001 BUTTON,CAP101L AD301686 743WKA0037 SPRING,FLAP101M AE001324 742WKA0001 SPRING,DVD-FLAP101N AE003110 800WQ0A052 FELT SHEET101O AE003462 752WSAA068 SHIELD BUTTON,DVD

102 AE003111 7A702A002A BACK CABI ASS'Y102A AE000224 702WPA1000 CABINET,BACK102B AE003112 800WQ0A032 FELT SHEET102C AE003113 800WQ0A036 FELT SHEET

103 BZ710658 701WPA0751 HOLDER,DECK104 BZ710466 752WSA0230 SHIELD,CASE HEAD AMP105 BZ710659 752WSA0290 SHIELD,COMPO106 BZ710331 753WUAA006 SPRING,EARTH HEAD AMP107 AD301956 752WSA0308 SHIELD,COVER HEAD AMP108 BZ710498 85OP700038 HOLDER,END SENSOR109 BZ710459 761WPA0223 HOLDER,FBT

110 BZ710660 741WUA0021 SPRING,EARTH111 AE000007 7220001107 SHEET,HWC112 AD301957 755WPA0035 COVER,PCB113 AE004260 761WSA0158 ANGLE,DECK114 BZ710577 701WPA0686 HOLDER,DECK115 BZ710677 752WSA0287 ANGLE,FRONT116 BZ710259 762WPA0011 HOLDER,CRT WIRE117 BZ710260 899HV3T000 HOLDER,ANODE WIRE118 AD301574 744WUA0013 SPRING,EARTH119 AD301966 752WSA0327 SHIELD,COVER FPC

120 AD301688 7260000341 SHEET,CAUTION121 BZ710039 8995034000 CORD CLIP UL CO.122 AE002846 752WSA0384 ANGLE,DVD 2123 BZ710376 769WSA0011 WASHER CRT T=0.5124 AE000164 774WPA0005 HOLDER,WIRE-2125 AE000159 7260000346 SHEET,CRT NO.126 AE000733 7230007691 SHEET,JACK127 AE000157 724WNA0009 SHEET,PVC128 AE000160 752WSA0331 SHIELD,COVER DECK129 BZ710671 752WSA0292 SHIELD,AV JACK

130 AE004444 752WSAA086 DVD,TOP131 AE003463 752WSAA067 PLATE,BOTTOM132 AD301964 752WSA0324 VCR,TOP133 BZ710694 774WPA0002 HOLDER,WIRE134 BZ710618 755WPAA012 PLATE,COVER LIGHT (L)135 AE004167 722549A363 SHEET,RATING136 AD300132 7230006818 SHEET,CAUTION137 AE000161 752WSA0337 SHIELD,DVD138 AE000162 752WSA0343 HOLDER,VCR139 AE003764 899EFBA001 WIRING CLIP

140 AE004168 723000C599 SHEET,BAR CODE141 AE000010 791WHA0085 LAMIFILM,BAG142 AE003117 792WHA0522 PACKAGE,TOP143 AE003118 792WHA0523 PACKAGE,BOTTOM144 AE004169 793WCDC240 GIFT BOX145 AE004170 A5L0054975 INSTRUCTION BOOK KIT146 AD302406 JB5UD200 POLYBAG,INSTRUCTION(RED CAUTION)147 AE004171 J5L00501A INSTRUCTION BOOK(E)148 AE004172 J5L00510A INSTRUCTION BOOK(F)149 AE004445 795WCDA009 PAD

MECHANICAL REPLACEMENT PARTS LIST

150 AE000006 7220001119 SHEET,CSA WARNING151 AE004173 723000C600 POP LABEL

201 AD302054 8141J50C54 SCREW,TAP TITE(P) GW22 5x35202 BZ710035 8117540A64 SCREW,TAPPING(B0) TRUSS 4x16203 BZ710320 8117540804 SCREW,TAPPING(B0) TRUSS 4x8204 BZ710582 8109130B94 SCREW,TAP TITE(B) R PAN 3x29205 BZ710239 8109I30A04 SCREW,TAP TITE(B) WH7 3x10206 BZ710562 8109I30804 SCREW,TAP TITE(B) WH7 3x8207 BZ710019 8109630802 SCREW,TAP TITE(B) BRAZIER 3x8208 BZ710678 8109230804 SCREW,TAP TITE(B) BIND 3x8209 BZ710409 8107630B04 SCREW,TAP TITE(S) BRAZIER 3x20

210 BZ710018 8107630804 SCREW,TAP TITE(S) BRAZIER 3x8211 AD301968 8107230404 SCREW,TAP TITE(S) BIND 3x4212 BZ710030 8110630804 SCREW,TAP TITE(P) BRAZIER 3x8213 BZ710299 8107230604 SCREW,TAP TITE(S) BIND 3x6214 BZ710337 8107930604 SCREW,CUP(S) 3x6215 AE002618 810F130804 SEMS(F) 3x8

CHASSIS REPLACEMENT PARTS LIST

300 AE003122 A5J9027420A DECK ASS'Y A5J9027420A301 AE002754 85OA400240 PINCH ROLLER BLOCK (VA)302 BZ710682 85OA500026 AHC ASS'Y303 BZ710193 85OP200290 BELT,CAPSTAN (S)304 BZ710515 85OP600581 WORM305 BZ710094 85OP500083 BASE,AC HEAD306 BZ710112 85OP800324 SPRING,AC HEAD307 BZ710516 85OA000459 MAIN CHASSIS ASS'Y308 BZ710517 85OA200089 CLUTCH ASS'Y309 BZ710518 85OA200090 ARM IDLER ASS'Y

310 BZ710519 85OA300065 LOADING ARM S UNIT311 BZ710520 85OA300066 LOADING ARM T UNIT312 BZ710521 85OA400223 INCLINED BASE T UINT 3S313 BZ710522 85OA400232 P5 ARM ASS'Y 2314 BZ710650 85OA400235 TENSION ARM ASS'Y 2315 BZ710524 85OA400231 INCLINED BASE S UNIT316 AE000442 85OP800367 SPRING,LOCKER317 BZ710526 85OP900736 CASS,HOLDER318 BZ710527 85OP900748 CASS,SIDE L319 BZ710528 85OP900749 CASS,SIDE R

320 BZ710529 85OP900739 LOCKER,R321 BZ710530 85OA900228 LINK UNIT322 BZ710531 85OP000496 POST,CASS GUIDE323 BZ710532 85OP200316 REEL,S (S)324 BZ710533 85OP200317 REEL,T (S)325 BZ710534 85OP200308 GEAR,IDLER326 BZ710535 85OP200311 GEAR,CLUTCH327 BZ710536 85OP200312 GEAR,COUPLING328 BZ710537 85OP200313 LEVER,CLUTCH329 BZ710538 85OP300194 GEAR,MAIN LOADING

330 BZ710092 85OP400490 LEVER,TENSION331 BZ710093 85OP400492 HOLDER,TENSION332 BZ710366 85OP400520 CAP.P4333 BZ710762 85OP400542 BAND,TENSION334 BZ710540 85OP400533 CONNECT,TENSION335 BZ710541 85OP600573 ARM,BRAKE T336 BZ710763 85OP600584 BAND,BRAKE T337 BZ710543 85OP600577 CAM,PINCH ROLLER338 BZ710544 85OP600578 CAM,MAIN339 BZ710545 85OP600579 ROD,MAIN

340 BZ710546 85OP600582 GEAR,JOINT341 BZ710110 85OP800322 SPRING,TENSION342 BZ710547 85OP800360 SPRING,BRAKE T343 BZ710548 85OP800355 SPRING,COUPLING344 BZ710549 85OP800356 SPRING,RING345 BZ710565 85OP900750 LEVER,LINK 2346 BZ710551 85OP900744 LEVER,FLAP347 BZ710552 85OP900745 CASS,OPENER348 BZ710106 85OP700035 REFLECTOR,LED349 BZ710514 85OP900746 BRACKET,TOP 3V

501 BZ710049 8107226804 SCREW,TAP TITE(S) BIND 2.6x8502 BZ710058 83ETW30000 E-RING 3.0503 BZ710371 8107226404 SCREW,TAP TITE(S) BIND 2.6x4504 BZ710046 8102120604 SCREW,PAN M2x6505 BZ710050 8109126604 SCREW,TAP TITE(B) PAN 2.6x6506 BZ710553 810A130404 SCREW/WASHER(A) M3x4507 BZ710219 810A126504 SCREW/WASHER(A) M2.6x5508 BZ710056 82Q264713N POLYSLIDER WASHER 2.6x4.7xT0.13509 BZ710054 82P184505N POLYSLIDER WASHER(CUT) 1.8x4.5xT0.5

510 BZ710017 8107226604 SCREW,TAP TITE(S) BIND 2.6x6

CD1501 BZ614292 122H071704 CORD JUMPER 2H071704CD1502 AD301953 122Y021002 CORD JUMPER 2Y021002H5001 AD301675 1523Q91003 HEAD (AUDIO CONTROL) VTR-1X2RPE22-756H5002 AD301676 1543Q02014 HEAD (FULL ERASE) VTR-1X2ERS11-154

! M101 BZ710554 1596S98001 MOTOR (LOADING) MDB2B66 ! M2001 AE002696 1510S98040 CAPSTAN DD UNIT F2QVB33B

M2003 BZ710657 1589S11017 MICRO MOTOR I2OAL05 ! UN4001 AE003123 A5J9016500 CYLINDER UNIT ASS'Y A5J9016500

DVD DECK REPLACEMENT PARTS LIST

600 AE003124 A2D006A650 DVD MECHA ASS'Y A2D006A650601 AD301822 92P100022A TRAVERSE HOLDER602 AE002480 92P100080A RACK,FEED 1A603 AE002481 92P100081A RACK,FEED 2A604 AD301825 92P100035A LEVER,RACK FEED605 AD301826 92P200006A INSULATOR(F)606 AD301827 92P200007A INSULATOR(R)607 AD301846 92P100029A GEAR,FEED608 AE001179 92P300009A SPRING,RACK L609 AD301845 92P100028A GEAR,MIDDLE 3

610 AE002482 92P300019A SPRING,RACK FEED 1A611 AE002179 92P100040A ARM,IDLER 2612 AD301833 92P000001A CLAMPER PLATE613 AD301834 92P100019A RACK,LOADING614 AD301835 92P100020A MAIN FRAME M615 AE001336 92P100039A TRAY616 AD301837 92P100023A GEAR,MAIN617 AE002647 92P100082A CLAMPER 2618 AD301839 92P300002A SPRING,RACK LOADING619 AD301840 92P400002A MAGNET,CLAMPER

620 AD301847 92P100030A GEAR,IDLER621 AD301842 92P100025A GEAR,MOTOR622 AE002180 92P100083A GEAR,MIDDLE 1623 AD301844 92P100027A GEAR,MIDDLE 2

701 BZ710187 8110226804 SCREW,TAP TITE(P) BIND 2.6x8702 AD301851 8110120604 SCREW,TAP TITE(P) PAN 2x6703 AD301852 8107220504 SCREW,TAP TITE(S) BIND 2x5704 AD301853 8140117254 SCREW,PAN M1.7x2.5 P3705 AD301913 8110220804 SCREW,TAP TITE(P) BIND 2x8

CD2001 AD301855 122H0O1901 CORD JUMPER 2H0O1901CD2301 AD301856 122H080701 CORD JUMPER 2H080701CD2302 AE000148 06CH232101 CORD CONNECTOR CH232101CP1 AD301858 069JV80180 CONNECTOR PCB SIDE IMSA-9615S-08C-PP-A

! M2602 AD301861 1515S98001 FEED MOTOR BCD3B81PCB640 AD301862 A5E601V640 PCB ASS'Y BEC001APCB68A AD301863 A5E601V680 PCB ASS'Y BEC002ASW1 AD301866 0515S32001 SWITCH SSS-23-6SW2 AE001158 0500101036 PUSH SWITCH ESE22MH22

ELECTRICAL REPLACEMENT PARTS LIST

Location No. TSB P/N Reference No. DescriptionRESISTORS

! R401 BZ210244 R4X5T6562F R,METAL 5.6K OHM 1/6W ! R403 BZ210231 R4X5T6153F R,METAL 15K OHM 1/6W ! R405 BZ210231 R4X5T6153F R,METAL 15K OHM 1/6W ! R406 AD302023 R3X28A181J R,METAL 180 OHM 2W ! R412 BZ210021 R65582680J R,FUSE 68 OHM 1/2W ! R417 AD302023 R3X28A181J R,METAL 180 OHM 2W ! R423 BZ210051 R3X18AR47J R,METAL OXIDE 0.47 OHM 2W ! R429 BZ210150 R002T2010J RC 1 OHM 1/2W ! R430 AD301920 R5X34F2R7J R,CEMENT 0 2.7 OHM 10W ! R440 AD301921 R5X34F332J R,CEMENT 0 3.3K OHM 10W ! R445 BZ210104 R6558A2R7J R,FUSE 2.7 OHM 2W

R449 AE000746 R00202561J RC 560 OHM 1/2W ! R454 BZ210003 R3K181102J R,METAL 1K OHM 1W ! R814 BZ210026 R3X18A153J R,METAL OXIDE 15K OHM 2W ! R815 BZ210026 R3X18A153J R,METAL OXIDE 15K OHM 2W ! R816 BZ210026 R3X18A153J R,METAL OXIDE 15K OHM 2W ! R1701 BZ210206 R002T2155J RC 1.5M OHM 1/2W ! R1702 BZ210080 R0G3K2275K RC 2.7M OHM 1/2W ! R1706 AD300651 R002T4272J RC 2.7K OHM 1/4W ! R1714 BZ210248 R3X181R15J R,METAL OXIDE 0.15 OHM 1W ! R1717 BZ210249 R3X28A331J R,METAL OXIDE 330 OHM 2W ! R1718 BZ210250 R5Y2CE1R2J R,CEMENT 1.2 OHM 7W ! R1720 BZ210190 R63581R22J R,FUSE 0.22 OHM 1W

R2344 AE002014 R002021R2J RC 1.2 OHM 1/2WR2345 AE002014 R002021R2J RC 1.2 OHM 1/2WR3010 AD302206 R3X181180J R,METAL OXIDE 18 OHM 1WR3021 AE000147 R3X181220J R,METAL OXIDE 22 OHM 1W

CAPACITORSC005 BZ110154 E02L00102M CE 1000 UF 6.3VC321 BZ210176 E02LF3222M CE 2200 UF 25V

! C403 BZ110195 E02LU8220M CE 22 UF 100VC404 BZ110023 E62DFB470M CE 47 UF 160V

! C408 BZ210157 P4N8FJ562H CMPP 0.0056UF 1.25KVC412 BZ110136 P4J7F3394J CMPP 0.39 UF 250V PMS

! C418 BZ210161 P4N8FJ682H CMPP 0.0068UF 1.25KV ! C429 AD301434 E02LU4101M CE 100 UF 35V ! C430 BZ110101 E5EZF3222M CE 2200 UF 25V ! C434 BZ110055 E5EZF4102M CE 1000 UF 35V ! C446 BZ110225 E5EZFD220M CE 22 UF 250V

C449 BZ110202 C0PLRR713K CC 0.001 UF 2KV RC801 AD301321 CQG0CH412J CC 100 PF 50V CHC820 BZ110247 C0JBB0713K CC 0.001 UF 2KV B

! C1701 BZ110025 P2122B224M CMP 0.22 UF 275V ECQULC1705 AE000699 C0PLRR7S2K CC 560 PF 2KV RC1707 BZ110203 C0PLRR7W2K CC 820 PF 2KV RR

! C1708 BZ110226 C0JBB07H3K CC 0.0022UF 2KV B ! C1710 BZ110226 C0JBB07H3K CC 0.0022UF 2KV B ! C1711 AE002878 CD39E0MQ3M CC 0.0047UF 250V ! C1714 AE000700 E52DHC681M CE 680 UF 200V ! C1716 BZ110010 E02L03222M CE 2200 UF 25V ! C1717 BZ110055 E5EZF4102M CE 1000 UF 35V ! C1720 BZ110228 E62NFB221M CE 220 UF 160V ! C1728 AE001253 E02L01222M CE 2200 UF 10V

C1729 AE000699 C0PLRR7S2K CC 560 PF 2KV R ! C1732 BZ110078 E02L03102M CE 1000 UF 25V ! C1733 AE000467 E02LU54R7M CE 4.7 UF 50V

C3009 BZ110154 E02L00102M CE 1000 UF 6.3VDIODES

D101 AD301638 0010E00330 INFRARED LED LTE-3271T-012A-OD102 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77D103 BZ410021 D97U05R61B DIODE,ZENER MTZJ5.6B T-77D105 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77D106 BZ410094 D97U01501B DIODE,ZENER MTZJ15B T-77D108 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77

! D402 BZ410063 D2WTAU02A0 DIODE,SILICON AU02A-EICD403 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77D404 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77

! D408 BZ410021 D97U05R61B DIODE,ZENER MTZJ5.6B T-77D410 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EICD411 BZ410021 D97U05R61B DIODE,ZENER MTZJ5.6B T-77

! D412 BZ410063 D2WTAU02A0 DIODE,SILICON AU02A-EICD413 BZ410019 D97U03001B DIODE,ZENER MTZJ30B T-77

Location No. TSB P/N Reference No. DescriptionDIODES

D414 BZ410019 D97U03001B DIODE,ZENER MTZJ30B T-77 ! D415 BZ410063 D2WTAU02A0 DIODE,SILICON AU02A-EIC

D416 BZ410085 D2WXN40050 DIODE,SILICON 1N4005-EICD417 BZ410022 D97U06R81B DIODE,ZENER MTZJ6.8B T-77D418 BZ410037 D97U03301B DIODE,ZENER MTZJ33B T-77D419 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77D601 AD300070 D97U01201B DIODE,ZENER MTZJ12B T-77D602 AD300070 D97U01201B DIODE,ZENER MTZJ12B T-77D603 AD300070 D97U01201B DIODE,ZENER MTZJ12B T-77D605 AD300070 D97U01201B DIODE,ZENER MTZJ12B T-77D801 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77D802 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77D803 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77D804 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77D805 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77D806 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77D1702 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77D1703 AE000141 D97U02R71B DIODE,ZENER MTZJ2.7B T-77

! D1704 BZ410007 D23TGP15J0 DIODE,SILICON RGP15J-G23 ! D1705 BZ410062 D2WTRM11C0 DIODE,SILICON RM11C-EIC ! D1706 BZ410062 D2WTRM11C0 DIODE,SILICON RM11C-EIC ! D1707 BZ410007 D23TGP15J0 DIODE,SILICON RGP15J-G23

D1709 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77 ! D1710 BZ410062 D2WTRM11C0 DIODE,SILICON RM11C-EIC ! D1711 BZ410062 D2WTRM11C0 DIODE,SILICON RM11C-EIC

D1712 BZ410067 D97U02R21B DIODE,ZENER MTZJ2.2B T-77 ! D1713 BZ410010 D28T21DQN9 DIODE,SCHOTTKY 21DQ09N-TA2B1

D1715 AD300671 D97U01801B DIODE,ZENER MTZJ18B T-77D1716 AD300731 D2WXN49370 DIODE,SILICON 1N4937D1717 AD300671 D97U01801B DIODE,ZENER MTZJ18B T-77

! D1718 AD300731 D2WXN49370 DIODE,SILICON 1N4937 ! D1719 BZ410115 D2LKB340L0 DIODE,SCHOTTKY SB340L-6737

D1720 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77D1721 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77

! D1722 AD300731 D2WXN49370 DIODE,SILICON 1N4937 ! D1723 AD301980 D2CF2016L0 DIODE,SILICON FE201-6L49

D1724 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77D1726 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77D1727 BZ410022 D97U06R81B DIODE,ZENER MTZJ6.8B T-77D1728 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77D1730 AD301980 D2CF2016L0 DIODE,SILICON FE201-6L49D1732 AD300070 D97U01201B DIODE,ZENER MTZJ12B T-77D1733 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77

! D1734 BZ410010 D28T21DQN9 DIODE,SCHOTTKY 21DQ09N-TA2B1D2201 BZ410022 D97U06R81B DIODE,ZENER MTZJ6.8B T-77D2205 BZ410087 0021E2Q140 LED LTL-1CHEE-002AD2206 BZ410087 0021E2Q140 LED LTL-1CHEE-002AD2207 BZ410087 0021E2Q140 LED LTL-1CHEE-002AD2601 BZ410121 DDARDS1200 DIODE,SILICON KDS120RTKD3001 BZ410037 D97U03301B DIODE,ZENER MTZJ33B T-77D3002 BZ410021 D97U05R61B DIODE,ZENER MTZJ5.6B T-77D3003 BZ410090 D97U04R71B DIODE,ZENER MTZJ4.7B T-77D3004 BZ410077 D2WXSB1400 DIODE,SCHOTTKY SB140-EICD3005 BZ410012 D28TQS04N0 DIODE,SCHOTTKY 11EQS04N-TA1B2D3007 BZ410043 D2WT011E10 DIODE,SILICON 11E1-EICD3008 BZ410010 D28T21DQN9 DIODE,SCHOTTKY 21DQ09N-TA2B1D3011 BZ410010 D28T21DQN9 DIODE,SCHOTTKY 21DQ09N-TA2B1D4001 BZ410119 DDDRL41480 DIODE,SILICON MCL4148D4201 BZ410021 D97U05R61B DIODE,ZENER MTZJ5.6B T-77D4204 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77D4205 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77D4207 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77D5501 BZ410012 D28TQS04N0 DIODE,SCHOTTKY 11EQS04N-TA1B2D5502 BZ410006 D1VT001330 DIODE,SILICON 1SS133T-77

ICSIC101 AE003125 I51F58076A IC OEC8076AIC103 AD301641 I9UF032310 IC PST3231NRIC199 AE004165 A5L0054015 INIT DATA IC302 AD301983 I01FF58910 IC AN5891SA-E1V

! IC352 AD302184 I0FSP7522N IC AN7522N ! IC401 BZ611025 I03TD80400 IC LA78040

IC601 AD301765 I03FC63190 IC LA76319M-MPB-E

Location No. TSB P/N Reference No. DescriptionICS

IC602 AE000143 I1KF98L100 IC KIA78L10F-RTFIC1501 BZ611079 I05FE90A45 IC TC90A45FIC1502 AD301988 I0UF015010 IC MM1501XNREIC1504 AD301988 I0UF015010 IC MM1501XNREIC1505 AD301927 I0UF015040 IC MM1504XNRE

! IC1701 AD301771 000220001W PHOTO COUPLER PS2561L1-1-V(W) ! IC1702 AD302211 I1KJ9A431A IC KIA431A-AT

IC2301 BZ611126 I03F065600 IC LA6560IC2601 AE002837 ICQK067080 IC ZR36708TQCIC2602 AD301770 I07E00358F IC BA10358F-E2

! IC3001 AD301931 I1KA78R050 IC KIA278R05PI ! IC3002 AD301929 I1KA78R090 IC KIA278R09PI ! IC3003 AD301931 I1KA78R050 IC KIA278R05PI

IC3004 AD301931 I1KA78R050 IC KIA278R05PIIC4001 AE000842 ICQK067620 IC ZR36762IC4002 BZ611124 I5HJ004BF0 IC S-24C04BFJ-TBIC4003 BZ611130 I0GF9XZ010 IC PQ070XZ01ZPIC4005 AE000843 IF9J0164A7 IC M12L64164A-7TIC4007 AE003430 ICMJ0F8009 IC SST39VF800-70-4C-EKIC4501 BZ611095 I03F3205M0 IC LA71205M-MPBIC5501 BZ611114 I01F63FBP0 IC AN3663FBPIC8001 AD301988 I0UF015010 IC MM1501XNREIC8002 AD301988 I0UF015010 IC MM1501XNREIC8004 AE001295 I0QJ045800 IC NJM4580M(TE1)IC8502 AE002835 I17F02KEG0 IC PCM1742KEG/2K

TRANSISTORSQ101 BZ410097 0000M00390 PHOTO TRANSISTOR ST-304LQ102 BZ510021 TNYJC05001 COMPOUND TRANSISTOR DTC124EKAT146Q103 BZ410097 0000M00390 PHOTO TRANSISTOR ST-304LQ104 BZ410106 0002700680 PHOTO COUPLER RPI-352C40NQ105 BZ410106 0002700680 PHOTO COUPLER RPI-352C40NQ106 BZ510021 TNYJC05001 COMPOUND TRANSISTOR DTC124EKAT146Q107 BZ410107 0002700690 PHOTO COUPLER RPI-303Q108 BZ410107 0002700690 PHOTO COUPLER RPI-303Q110 BZ510020 TNYJB05001 COMPOUND TRANSISTOR DTC114EKAT146Q112 AE002626 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,SQ114 BZ510001 T6YJ1037K0 TRANSISTOR,SILICON 2SA1037AKT146R,SQ116 AE002626 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,SQ350 AE002626 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,S

! Q401 BZ510097 TCAT03227Y TRANSISTOR,SILICON KTC3227_Y-AT ! Q403 BZ510040 TDUU024990 TRANSISTOR,SILICON 2SD2499(LB0EC1) ! Q406 BZ510004 TA3T016240 TRANSISTOR,SILICON 2SA1624-AA

Q407 BZ510096 TNATB03005 COMPOUND TRANSISTOR KRC102MATQ408 BZ510087 TCAT032070 TRANSISTOR,SILICON KTC3207-ATQ409 BZ510004 TA3T016240 TRANSISTOR,SILICON 2SA1624-AAQ601 BZ510039 TNYTB05001 COMPOUND TRANSISTOR DTC114EKT147Q602 AE002626 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,SQ605 BZ510025 TPYJB05001 COMPOUND TRANSISTOR DTA114EKAT146Q606 AE002626 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,S

! Q802 BZ510009 TC3F042170 TRANSISTOR,SILICON 2SC4217(D,E)-RAC ! Q803 BZ510100 TCATC3199Y TRANSISTOR,SILICON KTC3199_Y-AT ! Q804 BZ510009 TC3F042170 TRANSISTOR,SILICON 2SC4217(D,E)-RAC ! Q805 BZ510100 TCATC3199Y TRANSISTOR,SILICON KTC3199_Y-AT ! Q806 BZ510009 TC3F042170 TRANSISTOR,SILICON 2SC4217(D,E)-RAC ! Q807 BZ510100 TCATC3199Y TRANSISTOR,SILICON KTC3199_Y-AT

Q1501 AE002626 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,SQ1502 BZ510109 TCAA3875SY TRANSISTOR,SILICON KTC3875S_Y_RTKQ1503 BZ510109 TCAA3875SY TRANSISTOR,SILICON KTC3875S_Y_RTKQ1702 BZ510069 TCATC31980 TRANSISTOR,SILICON KTC3198-AT(Y,GR)

! Q1705 BZ510098 T220033260 FET 2SK3326(2) ! Q1706 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-AT

Q2201 BZ510020 TNYJB05001 COMPOUND TRANSISTOR DTC114EKAT146Q2202 BZ510020 TNYJB05001 COMPOUND TRANSISTOR DTC114EKAT146Q2203 BZ510020 TNYJB05001 COMPOUND TRANSISTOR DTC114EKAT146Q2601 BZ510112 T67J1036K0 TRANSISTOR,SILICON 2SA1036KT146Q2602 BZ510112 T67J1036K0 TRANSISTOR,SILICON 2SA1036KT146Q2603 BZ510113 T27T030180 FET 2SK3018Q2604 BZ510113 T27T030180 FET 2SK3018Q2605 BZ510113 T27T030180 FET 2SK3018Q3001 AE002626 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,S

! Q3002 BZ510105 TCAT03209Y TRANSISTOR,SILICON KTC3209_Y-AT ! Q3003 BZ510105 TCAT03209Y TRANSISTOR,SILICON KTC3209_Y-AT

Location No. TSB P/N Reference No. DescriptionTRANSISTORS

Q3004 AE002626 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,S ! Q3005 AD301934 TBA0013660 TRANSISTOR,SILICON KTB1366(O,Y)

Q3006 AE002626 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,S ! Q3007 BZ510057 TAAT01281Y TRANSISTOR,SILICON KTA1281_Y

Q3008 BZ510081 TPYJA05001 COMPOUND TRANSISTOR DTA143EKAT146Q3009 BZ510020 TNYJB05001 COMPOUND TRANSISTOR DTC114EKAT146Q3010 BZ510105 TCAT03209Y TRANSISTOR,SILICON KTC3209_Y-ATQ3011 AE002626 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,S

! Q3014 BZ510105 TCAT03209Y TRANSISTOR,SILICON KTC3209_Y-ATQ3015 AE002626 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,SQ4004 BZ510109 TCAA3875SY TRANSISTOR,SILICON KTC3875S_Y_RTKQ4201 AE002626 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,SQ4202 BZ510026 TPYJC05001 COMPOUND TRANSISTOR DTA124EKAT146Q4203 AE002626 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,SQ4204 BZ510021 TNYJC05001 COMPOUND TRANSISTOR DTC124EKAT146Q4210 BZ510001 T6YJ1037K0 TRANSISTOR,SILICON 2SA1037AKT146R,SQ4211 AE002626 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,SQ4212 BZ510001 T6YJ1037K0 TRANSISTOR,SILICON 2SA1037AKT146R,SQ4501 BZ510109 TCAA3875SY TRANSISTOR,SILICON KTC3875S_Y_RTKQ4502 BZ510109 TCAA3875SY TRANSISTOR,SILICON KTC3875S_Y_RTKQ4503 BZ510026 TPYJC05001 COMPOUND TRANSISTOR DTA124EKAT146Q4504 BZ510070 TCAT032034 TRANSISTOR,SILICON KTC3203_Y-ATQ4505 BZ510073 TAATA12660 TRANSISTOR,SILICON KTA1266-AT(Y,GR)Q4506 AE002626 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,SQ4507 AE002626 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,SQ4509 BZ510001 T6YJ1037K0 TRANSISTOR,SILICON 2SA1037AKT146R,SQ4511 BZ510001 T6YJ1037K0 TRANSISTOR,SILICON 2SA1037AKT146R,SQ8002 AE002626 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,SQ8006 AE002626 T8YJ2412K0 TRANSISTOR,SILICON 2SC2412KT146 R,SQ8007 BZ510021 TNYJC05001 COMPOUND TRANSISTOR DTC124EKAT146Q8502 BZ510108 TAAA1504SY TRANSISTOR,SILICON KTA1504S_Y_RTKQ8503 BZ510108 TAAA1504SY TRANSISTOR,SILICON KTA1504S_Y_RTKQ8504 BZ510108 TAAA1504SY TRANSISTOR,SILICON KTA1504S_Y_RTK

COILS &TRANSFORMERSL001 BZ310001 021673101J COIL 100 UHL301 BZ310156 021375101K COIL 100 UHL402 BZ310063 022100027A COIL,LINEARITY ELH5L4113L403 BZ310004 021679472K COIL 4.7 MHL601 BZ310041 02167F101J COIL 100 UHL602 BZ310156 021375101K COIL 100 UHL603 BZ310118 02AHB9A972 CORE,FERRITE W5T29X7.5X19L604 BZ310118 02AHB9A972 CORE,FERRITE W5T29X7.5X19L804 BZ310156 021375101K COIL 100 UHL1501 BZ310141 02167F100J COIL 10 UHL1502 BZ310043 021LA6150K COIL 15 UHL1504 BZ310170 021673151K COIL 150 UHL1505 BZ310042 021LA6101K COIL 100 UHL1506 BZ310042 021LA6101K COIL 100 UH

! L1701 BZ310180 029T000105 COIL,LINE FILTER 2R2A752F28 ! L1703 BZ310066 028R200024 COIL,DEGAUSS 8R200024

L1704 AD301539 02AHB0A0A4 CORE,FERRITE W5T_20*10*10AL3001 AD301785 02167E100K COIL R6-1 10 UHL3002 AD301785 02167E100K COIL R6-1 10 UHL4001 BZ310191 02167F2R2J COIL 2.2 UHL4002 BZ310118 02AHB9A972 CORE,FERRITE W5T29X7.5X19L4205 BZ310041 02167F101J COIL 100 UHL4502 BZ310114 031626009R COIL,BIAS OSC 1626009L4504 BZ310041 02167F101J COIL 100 UHL4505 BZ310040 02167F470J COIL 47 UHL4506 BZ310040 02167F470J COIL 47 UHL4509 BZ310156 021375101K COIL 100 UHL5501 BZ310042 021LA6101K COIL 100 UHL5502 BZ310039 02167F220J COIL 22 UHL5503 BZ310039 02167F220J COIL 22 UHL5504 BZ310039 02167F220J COIL 22 UHL8001 BZ310041 02167F101J COIL 100 UHL8002 BZ310042 021LA6101K COIL 100 UHL8003 BZ310041 02167F101J COIL 100 UHL8504 AE000828 02167F1R0K COIL 1 UHT401 BZ310172 045013003J TRANS,HORIZONTAL DRIVE ETH14Y47AY

! T1701 AD301935 048142065S TRANSFORMER,SWITCHING 8142065S

Location No. TSB P/N Reference No. DescriptionCOILS &TRANSFORMERS

L8502 AE000828 02167F1R0K COIL 1 UHL8503 AE000828 02167F1R0K COIL 1 UH

JACKS ! J801 AD301936 066F130021 SOCKET,CATHODE RAY,TUBE ISHS62S ! J2201 AE003431 060J131016 HEADPHONE JACK MSJ-2000_AG

J2202 AE002949 060J421036 RCA JACK MTJ-032-05A-30-FEJ2203 AE002950 060J421037 RCA JACK MTJ-032-05A-32-FEJ2204 AE002951 060J421030 RCA JACK MTJ-032-05A-31-FEJ4201 AE002759 060J431020 RCA JACK MSP-213V2-432_NI_LFJ4202 AE002758 060J411031 RCA JACK MSP-213V1-432_NI_LFJ8007 BZ614400 060J401082 RCA JACK MSP-251V-05PBSN

SWITCHESSW101 BZ612016 0508S11001 SWITCH (LEAF) LSA-1144EAUSW2201 BZ612010 0504101T34 SWITCH,TACT EVQ21505RSW2202 BZ612010 0504101T34 SWITCH,TACT EVQ21505RSW2203 BZ612010 0504101T34 SWITCH,TACT EVQ21505RSW2204 BZ612010 0504101T34 SWITCH,TACT EVQ21505RSW2205 BZ612010 0504101T34 SWITCH,TACT EVQ21505RSW2206 BZ612010 0504101T34 SWITCH,TACT EVQ21505RSW2207 BZ612010 0504101T34 SWITCH,TACT EVQ21505RSW2251 BZ612010 0504101T34 SWITCH,TACT EVQ21505RSW2252 BZ612010 0504101T34 SWITCH,TACT EVQ21505RSW2253 BZ612010 0504101T34 SWITCH,TACT EVQ21505RSW2254 BZ612010 0504101T34 SWITCH,TACT EVQ21505RSW2255 BZ612010 0504101T34 SWITCH,TACT EVQ21505RSW2256 BZ612010 0504101T34 SWITCH,TACT EVQ21505RSW2257 BZ612010 0504101T34 SWITCH,TACT EVQ21505RSW2258 BZ612010 0504101T34 SWITCH,TACT EVQ21505R

VARIABLE RESISTORSVR404 BZ210218 V1K63H3BTE VOLUME,SEMI FIXED NVG6TLTAB222VR1701 AD301937 V1K6314BTE VOLUME,SEMI FIXED NVG6TLTAB103

P.C.BOARD ASSEMBLIESPCB010 AE004166 A5L0054010 PCB ASS'Y VMC293BPCB080 AE003128 A5L0024080 PCB ASS'Y TMC564BPCB110 AE003129 A5L0024110 PCB ASS'Y TCC426BPCB130 AE003130 A5L0024130 PCB ASS'Y VMC319APCB270 AE003131 A5L0024270 PCB ASS'Y TECB10B

MISCELLANEOUSB401 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0B402 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0B403 BZ310121 024HT03553 CORE,BEADS W5RH3.5X5X1.0B1703 BZ310129 024HT03564 CORE,BEADS W4BRH3.5X6X1.0B2201 BZ310129 024HT03564 CORE,BEADS W4BRH3.5X6X1.0B2601 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04B2602 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04B2603 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04B2604 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04B2605 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04B4001 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04B4002 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04B4003 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04B4004 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04B4005 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04B4006 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04B4007 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04B4008 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04B4009 BZ310122 024HT03563 CORE,BEADS W4BRH3.5X6X1.0X2B4010 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04B8001 BZ310122 024HT03563 CORE,BEADS W4BRH3.5X6X1.0X2B8502 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04B8503 BZ310186 024HC31022 CORE,BEADS FCM2012H-102T04BL001 BZ310014 023C00022A COIL,BALUN HPN-01BT001 AE000012 1412004008 BATTERY,MANGAN R03(AB)E_2P_GBT002 AE000012 1412004008 BATTERY,MANGAN R03(AB)E_2P_GCD002 BZ614411 06CU011902 CORD,CONNECTOR CU011902CD303 BZ614424 06CU149001 CORD,CONNECTOR CU149001CD602 AD302218 06CU291701 CORD,CONNECTOR CU291701CD603 AE000133 06CU284501 CORD,CONNECTOR CU284501CD604 AE000132 06CU282401 CORD,CONNECTOR CU282401CD802 BZ614310 WCL6844038 FLAT CABLE AWM2468 A WG26 5C GRAY 440MMCD803 BZ614378 06CU823001 CORD,CONNECTOR CU823001CD805 BZ614378 06CU823001 CORD,CONNECTOR CU823001

Location No. TSB P/N Reference No. DescriptionMISCELLANEOUS

CP001 BZ614444 069D01001A CONNECTOR PCB SIDE 003P-2100CP101 BZ614289 06972C0010 CONNECTOR PCB SIDE TMC-J12P-B2CP303 AD301045 069S140419 CONNECTOR PCB SIDE A2502WV2-4P

! CP404 BZ614303 069S450089 CONNECTOR PCB SIDE A1561WV2-A5PCP601 AD301943 069S240639 CONNECTOR PCB SIDE A2001WR2-4PCP602 BZ614462 067U009039 WIRE HOLDER B2013H02-9PCP603 AD301944 067U008029 WIRE HOLDER B2013H02-8PCP604 AD301796 069S280629 CONNECTOR PCB SIDE A2001WV2-8PCP803 BZ614269 069S320010 CONNECTOR PCB SIDE A2361WV2-2PCP805 BZ614269 069S320010 CONNECTOR PCB SIDE A2361WV2-2P

! CD1702 BZ614407 120R415906 CORD,AC BUSH 0R415906CD2251 BZ614408 06CU220701 CORD,CONNECTOR CU220701CD4002 AE003640 06CU2B3301 CORD,CONNECTOR CU2B3301CD4501 BZ614373 122F061502 CORD,JUMPER 2F061502CD8501 AE000134 122H0C2204 CORD,JUMPER 2H0C2204CP1702 AD301944 067U008029 WIRE HOLDER B2013H02-8P

! CP1704 BZ614283 069S420110 CONNECTOR PCB SIDE A1561WV2-2PCP1707 BZ614444 069D01001A CONNECTOR PCB SIDE 003P-2100CP1708 BZ614444 069D01001A CONNECTOR PCB SIDE 003P-2100CP2201 BZ614416 069S220629 CONNECTOR PCB SIDE A2001WV2-2PCP2601 AD302396 069JYOT099 CONNECTOR PCB SIDE IMSA-9631S-24Y901CP2602 AD301858 069JV80180 CONNECTOR PCB SIDE IMSA-9615S-08C-PPCP2603 AD301795 069S230639 CONNECTOR PCB SIDE A2001WR2-3PCP4501 BZ614011 0697290620 CONNECTOR PCB SIDE TOC-C09X-A1CP4502 BZ614050 069J760029 CONNECTOR PCB SIDE IMSA-9604S-06Z14CP4503 AD301649 067U002019 WIRE HOLDER B2013H02-2PCP602B BZ614458 069S290629 CONNECTOR PCB SIDE A2001WV2-9PCP603B AD301796 069S280629 CONNECTOR PCB SIDE A2001WV2-8PCP8001 BZ614214 069S2B0629 CONNECTOR PCB SIDE A2001WV2-11PCP8002 AD301797 069J7C0029 CONNECTOR PCB SIDE IMSA-9604S-12Z14CP802A BZ614276 067U005049 WIRE HOLDER B2013H02-5PCP802B BZ614276 067U005049 WIRE HOLDER B2013H02-5PCP8502 AD301798 069J7C0019 CONNECTOR PCB SIDE IMSA-9604S-12Z13CUS011 BZ710148 800WFAA007 CUSHION BCUS012 BZ710149 800WFAA008 CUSHION CEL001 BZ614044 124120301A EYE LET XRY20X30BDEL002 BZ614043 124116281A EYE LET XRY16X28BDEL003 BZ614044 124120301A EYE LET XRY20X30BDEL004 BZ614043 124116281A EYE LET XRY16X28BD

! F1701 BZ614422 081PC6R305 FUSE 51MS063L ! FB401 AD302038 043220058F TRANSFORMER,FLYBACK FJN20A003

FH1701 AE002634 06710T0009 HOLDER,FUSE EYF-52BCYFH1702 AE002634 06710T0009 HOLDER,FUSE EYF-52BCYOS2201 AD301949 0773071003 REMOTE RECEIVER RPM7138-WH10

! RY1701 BZ612009 0560V20115 RELAY ALKS321 ! SP351 BZ614381 070C546004 SPEAKER SG04H02BRA ! SP352 BZ614381 070C546004 SPEAKER SG04H02BRA

TM101 AD301950 076D0FG020 TRANSMITTER ORV201N36010 ! TU001 AE000273 0163300005 RF UNIT 115-V-K015AR_B ! TH1701 BZ410079 DF5EL3R0A0 DEGAUSS ELEMENT ZPB45BL3R0A ! V801 AD302039 098Q210448 CRT W/DY A51AKL13X04

X101 BZ613006 100DA32R01 CRYSTAL DT-26X102 BZ613033 100CT01403 CRYSTAL HC-49/U-SX601 AD301951 100CT3R532 CRYSTAL HC-49/U-SX4001 AD301803 100BT02701 CRYSTAL HC-49U/SX4501 BZ613017 100CT3R502 CRYSTAL HC-49/U

RESISTORRC................... CARBON RESISTOR

CAPACITORSCC................... CERAMIC CAPACITORCE................... ALUMI ELECTROLYTIC CAPACITORCP................... POLYESTER CAPACITORCPP.................. POLYPROPYLENE CAPACITORCPL.................. PLASTIC CAPACITORCMP.......................METAL POLYESTER CAPACITORCMPL................ METAL PLASTIC CAPACITORCMPP................ METAL POLYPROPYLENE CAPACITOR

TOSHIBA CORPORATION1-1, SHIBAURA 1-CHOME, MINATO-KU, TOKYO 105-8001, JAPAN

toshiba-mw20fp1c_tv+vcr+dvd video player sm

Documents

dvd player/vcr with line-in recording...dvd player/vcr with...

converting vcr tape to dvd

dvd/vcr progressiveo pe n/ cl se po wer 7 feature summary...

multimedia services users guide...

dvd vcr sat cbl aux epg · tv dvd vcr sat aux stream e p g...

setting up the polycom eagleeye...

tv/dvd/vcr code list

manual del usuariolg dc-596m-s dvd+vcr

vcr functions dvd functions information - toshiba...

toshiba dvd hdd rd-xs52su manual user guide

dvd recorder / vcr

vcr/dvd recorder combination model dv-rw250h€¦ ·...

electronics - diagramas electrónicos para...

toshiba dvd vcr player sd-v295

zv427fx4 connections zv427fx4 a dvd recorder/vcr line-in...

dvd recorder and s-vhs vcr in one package – easy-to-use...

dvd recorder & vhs combo player rdr-vx530 - … ·...

lg dvd/magnétoscope intégrés (touche vcr) / téléviseur

dvd recorder-vcr d-vr3sc - toshiba...

dvd toshiba sd-3990su, sd-3990sc service manual