tips to help with this exam - ohs.me.uk · 2014-10-25 · tips to help with this exam •read the...
Post on 15-Apr-2020
1 Views
Preview:
TRANSCRIPT
Tips to help with this exam
• Read the question! pick out the key words
• Try to relate the question to a workplace
situation
• Break questions down e.g.. design, use,
maintenance where appropriate
• Remember HS principles e.g.. RA,
Controls, People
Electricity at work
regs 1989
Regs 1 -3
1 Citation
2 Interpretation
3 persons with duties
Reg 4 Systems, work activities & protective
equipment
•Systems must be maintained to prevent danger
•All work activities must be carried out in a
manner not to give rise to danger
•Equipment provided to protect people working
on live equipment must be suitable and
maintained
Reg 5 Strength & capability of electrical
equipment
•Must be able to withstand effects of its
load
•Must be able to withstand effects of
transient or pulse currents
Reg 6 Adverse or hazardous
environments
•Must be suitable for the environment and
conditions that are reasonable foreseeable
•Mechanical dame e.g.. vehicle, people
•Weather, temp, pressure, natural hazards
e.g.. bird droppings
•Wet, dusty, corrosive conditions, presence
of flammable dusts
•Flammable or explosive atmospheres
Reg 7 Insulation protection & placing of
conductors
•Prevent danger from direct contact
through insulation etc
Reg 8 Earthing or other suitable
precautions
•Purpose to prevent harm from indirect
contact e.g.. casings
Reg 9 Integrity of referenced conductors
•Ensure electrical continuity is never broken
Reg 10 Connections – must have
adequate mechanical strength e.g..
plugs
Reg 11 means of protecting from excess
current e.g.. fuse, RCD
Reg 13 Precautions for work on equipment
made dead
•Identify the circuit, don’t assume the labelling
is correct
•Disconnection & isolation e.g.. isolation
switches (lock off) removal of fuse/plug
•Notices, signage and barriers
•Prove system dead test the test device
•Earthing
•PTW
Reg 12 Means of isolation
Reg 14 Work on or near live conductors
•Competent staff
•Adequate information
•Suitable tools: insulated tools, protective
clothing
•Barriers or screens
•Instruments and test probe to identify what
is live and what is dead
•Accompaniment
•Designated test areas
•PTW
Reg 15 Working space, access & lighting
Where there are dangerous live exposed
conductors space should be adequate to
•Allow persons to pull back from the hazard
•Allow persons to pass each other
Lighting should be adequate preference e to
natural then artificial
Reg 16 Persons to be competent to
prevent danger and injury
•An understanding of the concepts of
electricity and the risks involved in work
associated with it
•Knowledge of electrical work and
qualification in electrical principles
•Experience
•Knowledge of systems of work & ability to
recognise risk & hazards
•Physical attributes to recognise elements
of the system e.g.. not colour blind
Robot Safety
Groups at risk
• Operators
• Maintenance
engineers
• Teachers
Interlocked perimeter fencing
• Positioned to prevent access to
dangerous parts
• Normally 2 meters high
• Rigid panels
• Securely fastened to floor
• Infill suitable to protect from other hazards
e.g.. ejected materials
• Gates/access points to be interlocked
• Hinged/sliding interlocks
• Trapped key exchange
• Solenoid lock
Emergency Stops provided at
• Control stations
• Teacher control pedestal
• All workstations
• Other positions as necessary
Layout (Envelope)
• Planning during design
• Minimise need to approach robot
• Good viewing arrangements outside
of enclosure
• Adequate distance between robot &
enclosure
• Prevent trap points
• Adequate access to rescue injured
person
• Access only through interlocked
gates or similar
Electro-sensitive safety systems
• Used in conjunction with fencing
• Photo cell device
• Trip with use of light curtains
arranged
vertically/horizontally/diagonally
• Pressure mats around machinery
• Trip wires etc robot comes into contact
with a person should trip
• All should require manual restart
Positive stops
• Limits movement of robot
• Defined limits to prevent trap points
• Avoid creating additional trap points
Brakes
• Prevent danger of fall under gravity
• Should be applied automatically when
machine stops
Entry Procedures
• SSOW defined/RA carried out
• Analysis of hazards in all possible
modes of operation
• Release of stored energy before
entry/work
• PTW
• ISOLATION required
Preventative maintenance and
inspections
•Software checks to avoid aberrant
behaviours
•Stop devices
•Guard checks
•Integrity of parts for wear damage
e.g.. hydraulic rams
TEACHING
•Remotely where possible
•Slow mode when live
Behavioural - People
•Hazard aware
•Trained in procedures e.g.. entry,
emergency
•Adequately supervised
Machinery ‘Essential health
and safety requirements’
that should be addressed
Reference – Supply of machinery
regs 1992 schedule 3
Consider
•Installation
•Use
•Maintenance
•Decommissioning
General
• Principles of safety integrations
• Materials & products used/created
• Lighting arrangements
• Handling & Installation of machine
Controls
• Safety & Reliability
• Control devices
• Means of starting stopping device
• Normal stopping
• Emergency stopping
• Mode of operation selection
• Failure of power supply
• Software design
• Failure of control circuit
Indicators
• Information devices
• Warning devices e.g.. alarms/lights
• Warning of residual risks
• Markings
• Instructions
Protection against other hazards
• Electricity e.g.. insulation
• Other stored energy e.g.. hydraulic
pressure
• Errors of fitting
• Fire/explosion
• Noise
• Dust/gases e.g.. extraction
• Vibration
• Radiation
Required Characteristics of guards
• Fixed
• Movable guards
• Adjustable guards
• Special requirements for protective
devices
Protection against mechanical
hazards
•Stability/anchorage – e.g.. floor fixings
•Risk of break up during operation
•Falling objects/ejected parts
•Surface risk e.g.. sharp/hot/cold
•Variable speeds
•Moving parts
•Choice of protection arrangements
Maintenance
• Machinery maintenance
• Access to operating and servicing
position
• Isolation of energy sources
• Operator intervention
• Cleaning of internal parts
• Lubrication etc
Range of issues &
evidence to examine
during investigation of lift
op failure (crane)
Key Factors
• Crane
• Lift
• Forensic evidence
Lift
• Load
• Weight
• Gravity – lifting point?
• Slinging method – appropriate for load?
• Type of lift
• Static
• Slewing
• Lift & Travel
• Drag
• Site conditions e.g.. wet, windy, foggy,
obstructions/excavations
• Lifting plan, witness statements visual
inspections
• Training records
• Crane driver, slingers, rigger, banksman
Forensic evidence
• Type of failure
• Buckling
• Brittle
• Ductile
• Integrity of Jib look for evidence of
alterations, repair, corrosion, missing
bolts
• Settings & functionality of controls,
switches & alarms
Crane
• Type –suitable for lift?
• SWL of crane
• Alarm system working?
• SWL indicator/radius indicator
• Exceeded?
• Operational criteria e.g.. adequate
strength & stability
• Design characteristics
• Counter balance
• Out riggers
• Configuration for task e.g.. level
ground, positioning to load, distance
required to travel
• Maintenance & certification records
• Lifting history
Factors Effecting
Structural Safety
Subsidence
• Signs of defects include
• Semi random cracks in walls
• Sagging in arches/beams
• Fractures of pipe joints
• Builds over mine tunnels or large
holes can cause serious deformation
Dead loads
• Material which buildings is
constructed from e.g.. columns,
beams, floors
Wind
• Physical damage
• Dampness by driving rain moisture
into buildings
• Can lift roof covering
Vibration & Sudden Shocks
• Traffic/machinery
• Can effect foundations of buildings
• Buildings can be struck by
vehicles/plant
Solar Radiation
• Absorbed when it strikes a material
• Materials expand when warm
• Contract when cooling
• Solar radiation causes surfaces to
heat up quickly
• Rain falling onto hot surfaces can
causes severe shock and result in
tension cracking e.g.. roof membrane
Live Loads
• People
• Furniture
• Equipment
Constantly moving and changing every
day
Dynamic loads
Dead loads & Live loads change
slowly and are called static loads
Other loads can change suddenly such
as wind gust, these loads are dynamic
Rain/snow/hail
• Moisture greatest cause of
deterioration
• Rising damp causes flaking and
cracking
• Frozen water causes stresses &
cracks
• Moisture promotes rust in metals
• Moisture creates environment for
fungal growth
• Build of snow/ice on roofs increases
structural loading
Atmospheric contaminants
• Combine with moisture to form acid
rains which attack materials
• Sulphur dioxide
• Carbon dioxide
• Oxygen
• Ozone
Timber Decay
• Deterioration of timbers can
severely cases lead to building
collapse
• Due to wet rot/dry rot/fungal attack
& insect attack
Corrosion
• Metal combines with oxygen in the
air to form rust
Key Factors
• Dead load
• Live load
• Dynamic load
• Solar radiation
• Vibration/sudden shocks
• Weather
• Atmospheric contaminants
• Timber decay
• Corrosion
• Subsidence
Effects Fire on
materials
Steel
• Will expand with heat
• Loss of strength normally @600
Celsius
• Deform & Buckle
• When cooled will regain strength but
properties may have changed
• Acts as conductor transferring heat
thus spreading fire
Concrete
• Limited expansion
• Cracks and spalls made worse by
expanding reinforcement steel e.g..
rebar
• Poor conductor of heat
• Will have lost structural strength
when cool
Wood
• Thin sections will burn promoting fire
spread
• The charred surface of thick timber
will act as insulation to inner timber
• Dependant on species
• Generates smoke & allows surface
propagation of fire
• Strength after burning depends on
original thickness and proportion loss
to fire
Precautions to prevent
failure of materials
Steel
•Concrete cladding
•Compartmentalise to reduce
conduction
•Automatic cooling with sprinkler
system etc.
Concrete
•Selection of type and mix to
improve fire resistance
•Increase thickness of concrete
from exposed surface to steel
reinforcement (rebar)
Wood
• Selection of thick timbers
• Selection of timber e.g.. hardwood
burns slower than soft wood
• Treat with fire retardant substance
General precautions
•Sprinkle system
•Fire resistance cladding
•Early fire detection
•Control of ignition sources & reduction of fuel type materials – fire risk
assessment and adequate controls implemented
Confined space
entry
Key Factors/Regs
• Confined space regs
• Reg 4(1) Avoid
• Reg 4(2) If must SSOW to be
defined
• Reg 5 Define Emergency
rescue plan
Specified occurrence
• Fire or explosion
• Loss of consciousness/asphyxiation
from gas, fumes or lack of oxygen
• Drowning
• Asphyxiation arising from free
flowing solid e.g.. mud slide
• Loss of consciousness arising from
high temperature
Reg 5 Emergency planning/Procedure
• Communication with workers in
vessel/space
• Raising the alarm
• Emergency rescue e.g.. tripod winch
• Provision of stand by man/first aider
• Means of fire fighting
• Provision of emergency escape sets
• Communication with emergency services
Reg 4(2) SSOW
Risk assessment to consider
• People conducting work e.g.. age,
experience, training
• Likelihood of flammable/explosive
atmosphere from previous contents
• Access/egress
• Contaminated air from previous contents
• Build up of heat
• Duration of activity
• Lack of oxygen
• Working at height within CFP
• Ingress of solids/liquids
• Impact of other plant
• Outside environment Weather, other
activities
• Isolations required
• Emergency situation
Reg 4(2) SSOW cont.
Control measures
• Trained and experienced workers to conduct activity
• Entry procedures, use of equipment e.g.. BA
• Purge of space with inert gas e.g.. nitrogen
• Forced air ventilation
• Atmospheric testing e.g.. gas/oxygen level monitoring
• Suitable electrical equipment e.g.. intrinsically safe
• Earthing arrangements
• Job rotation e.g.. control of heat fatigue
• Appropriate access and egress e.g.. scaffold, ladders
• WAH provision, e.g.. scaffold internal of space
• Barriers to prevent unauthorised access
• Appropriate isolations as necessary
• Appropriate PPE e.g.. anti static clothing, BA, gloves etc.
Reg 4(1) Avoid if possible
Consider other options
• Cameras
• Cleaning lances
• Robotic inspection
Last paper
Key factors to protect
against ignition from static
of a flammable vapour
during transfer of
containment of liquids
Worker involved trained and
competent in operation e.g..
aware of hazards and
precautions necessary
Over fill protection system
e.g.. high level indicator,
interlocked shut down
Avoid splash/spray filling
Controlling pump rate
• Speed slow – not to
propagate static build up
Use of inert gas blanketing
above the liquid
Earthing of all conductive
surfaces e.g.. tankers, pipe
work, containers e.g.. IBCs
Keep at zero potential,
Earthing should be
interlocked to pump system
Provision of anti static
clothing including footwear
Implementation of a vapour
return system
Complete containment of
flammable liquid, not leaks,
seals joints etc
Last paper
EPA section 34
Concepts of duty of
care
Controlled waste
• Household
• Commercial
• Industrial
Exceptions
• Agricultural
• Mines/Quarries
• Radioactive waste
Key points
• Controlled waste
• Duty of care ‘categories of
persons’
• Duty of care
Duty of care
Reasonable steps to prevent;-
•Deposits of CW without waste management license
•Treatment, storage, disposal in manner likely to cause
pollution
•Treatment, storage disposal with out waste handling license
•Prevent escape
•Transfer to unlicensed holding
•Transfer without written description
Duty of care Categories of persons
Persons who
• Produces CW
• Imports CW
• Carries CW
• Stores CW
• Treats CW
• Disposes of CW
Exceptions of house holders
Automatic Fire Detection Heat Detectors • Fixed temperature type
– Thermocouple detects when a set temperature is reach
• Rate of rise type – Detects abnormal temp rises
(sudden)
– Electronic resistors
– Usually incorporate fixed temp element as well
Unsuitable for • Rapid heat rise workplace e.g..
laundrettes, steel manufactures
Smoke Detectors • Ionisation type
–Small radioactive source to ionise a chamber into which smoke enters during a fire. Detector reacts to change in current caused by neutralisation of ions by smoke particles
• Optical type –Responds to the obstruction of a focused light ray or the scattering of light from an optical ray by smoke
Unsuitable for • Dusty workplace due to false alarms
e.g.. flour mills
• Workplace which generate smoke e.g.. kitchen, welding workshops
Heat (fixed or rate of rise) where there are fumes, steam or other particles may be present that would be
detectable by a smoke detector and cause false alarms.
Smoke (optical or ionization) everywhere else within reason Last paper
Issues to address
when planning a fire
evacuation
Publishing and training of
procedure
• Regular drills
• Documented
• Fire log book
Numbers of people to evacuate
& physical ability
•Escape routes
•Distance of travel required
•Alternatives routes
Equipment and security
• Equipment may need shutting
down safely
• Security could be an issue
after evacuation
Emergency light and signs
• Exits
• Escape routes
Refuges and safe havens
(muster points)
Raising the alarm
• Consider any disabilities and
make provision for e.g.. visual
alarm for deaf people
• Contacting the emergency
service e.g.. interlocked alarm
system or manual call
Training of fire wardens
• Zoning
• Areas of responsibility Roles and responsibilities
• Managers
• Staff
Prevention of re-entry
Liaison with emergency services
• Numbers of people involved
• Specific hazards in building
Accounting for people
Reducing risk of dust cloud
explosion and mitigating
explosion effects
Key principles
• Dust control
• Ignition source control
• Mitigation of explosion effects
• DSEAR regs
• Zoning
Ignition control
• No smoking policy
• No mobile phones
• Provision and use of anti
static clothing and footwear
• Earth bonding of equipment
• Assessment in compliance
with DSEAR regs
• Appropriate zone identification
of areas i.e.. 20, 21 or 22
• Use of spark protected
equipment – intrinsically safe
to appropriate zone
• Abnormal activities generating
sparks under hot work PTE
Dust control
• Damping down
• Extraction of dust at point of transfer
(LEV)
• Interlock device to prevent
overfilling of vessels
• High standard of house keeping
• Ensuring that systems are sealed
where possible
Mitigating effects of explosion
• Equipment able to withstand
explosion
• Venting and explosion panels
• Bursting disc on vessels
• Suppression – inerting
• Compartmentalisation – minimise
effected
Design features to
reduce risk of
vehicle/pedestrian
collision
Where possible re-route
pedestrians away from
vehicle movement area e.g..
elevated corridors
Allow sufficient space for
vehicles to operate
Introduce safe crossing
points e.g.. zebra crossing
Segregate pedestrians from
vehicles with the use of fixed
barriers
Avoid creation of blind bends
if unavoidable install wall
mounts mirror (convex) to
improve visibility
Create safe passing places
Separate access & egress points
for vehicles/pedestrians
Direction of vehicle
movement control e.g.. force
one way traffic
Where possible design
routes such to
eliminate/reduce the need for
reversing
Ensure lighting is adequate
and suitable for tasks carried
out
Consider automated system
(robotic to almost eliminate
pedestrians requiring access
Aspects of a working
environment which
increase electrical risk
Mechanical hazards
• Vehicle impact
• Plant equipment nearby
• Abrasion from operate
equipment
Corrosive atmospheres
leading to corrosion of parts
Weather conditions
• Rain – moisture entering
• Freezing leading to crack
through expansion
• Heat
• Humidity
Flame proof
• Heavy duty of substantial build and enclosed. When
flammable atmosphere enters the equipment can withstand
and enclose an explosion and prevent the ignition of any
flammable atmospheres surrounding equipment
• May not be suitable for use in areas with combustible
powders of dust. May require special measure to prevent
ingress of water
Flammable/explosive
atmosphere
Intrinsically safe
• Restriction of electrical energy in
equipment, insufficient to create
heat/sparks
• Faults may increase energy levels above
safe limit
High/Low temperatures
Duties of designers
under CDM2007
Duties apply at all times e.g..
appointing of CDM co-
ordinator if notifiable Ensure that client is aware of
their duties
Ensure that they (designers)
are competent for the work
they do
Co-operate with others as is
necessary to manage risks
e.g.. contractors
Provide information for h & S
file
Take into account Workplace
(HS&W) regs when
designing workplace
structures
Co-operate with CDM co-ordinator &
other
Conduct risk analysis of
major design e.g..
HAZOP/FMEA
Inform of any
significant/unusual residual
risks
Avoid foreseeable risks
(construction and use)
SFAIRP during design by
•Eliminating hazards where
poss.
•Reduce remaining risk
•Give collective risk
reduction measures priority
over individual measures
Provide info with the design
to assist clients, contractors,
designers e.g.. notes for
drawings, rational behind
design decisions
Safe operation of bench
mounted circular saw
Safe operation and
adjustment of top guard
Provision of emergency
stops and means of isolation
Use of appropriate PPE e.g..
hearing protection/goggle,
dust mask
Effective guarding of blade
under bench
Use of push stick to feed
materials being cut
Ensure that operators are
suitable trained and
experience to use the saw,
also ensure appropriate level
of supervision
Ensure that the riving knife is
correctly positions through
risk assessment
Sufficient space around
equipment kept clear of
obstructions
Provision of LEV to remove
dust
Adequate lighting and saw
suitably fixed to floor
Regular maintenance and
safety inspection e.g.. guard
check
Pressure systems
causes of failure
Excessive Stress
• Ductility – amount of stretch before a
material ruptures
• Usually result of single stress over
load
• Materials can balloon due to
excessive pressure
Abnormal external loading
• Struck by something e.g.. vehicle
• FLT/Fuel tankers
• Explosion
Over pressure
• Catastrophic results e.g.. vessel
rupture
• Failure of relief valves can cause
• Normally systems tested to 3 times
normal operating pressure
Brittle fracture
• Fracture without deformation
• Brittle materials are strong but not
resistant to cracks
• Impact loading causes e.g.. rapid
temp changes, pressure differences
• High tensile & residual stresses
promote
Thermal fatigue & Shock
• Shock is sudden change in temp of
water
• Causes rapid expansion/contraction
of system components
• Leads to fatigue and material stress
ultimately failure of system e.g..
leaking pipes, fracture of vessels
Mechanical fatigue & Shock
• Pressure causes tensile stress in all
directions
• If stresses are greater than material
can cope with it will lead to ductile or
brittle failure
• Fatigue stress is usually progressive
• Fatigue failure often triggered by
surface interruption e.g.. grinding
marks, weld defects, notches etc
• Pressure focuses at root of defect
Overheating
• Can occur if alarms/controls fail
• Causes rise in pressure
Creep
• Under constant load
• Deforms over time (plastic)
• Temperature is important, materials
determine working temperatures that
can be used
Hydrogen attack
• Hydrogen seeps into gaps in
molecular frame work
• Causes stresses within framework
• Examples are cathode reaction,
electroplating
Corrosive Failure
• Chemical/electro-chemical attack by
atmosphere
• Only affects metals
• Materials lose strength can thin
• Occurs when oxygen levels of
carbon dioxide levels are high &
when PH levels are low or high
Technical & procedural
measures to minimise
likelihood of pressure
system failure
Key points
• Design
• Operation
• Inspection/Maintenance
Inspection
• Written scheme of examination –
statutory
• Pressure vessels
• Pipe work and valves
• Protective devices
• Pumps and compressors
• Prepared by competent person
• NDT/examination
Operation
• Use within performance envelope
• Operators trained and experience to
identify errors and prevent faults
through error arising
• Aware of safe operating limits
• Scheme of examination
• Equipment marked with operating
pressures/temperatures max/min
• Quality control
• Filtering/treating of water (boilers)
Design
• Take account of current safe practise
• Fit for purpose/CE marked
• Material constructed from suitable for
materials in process
• Expected life
• Maintenance/testing accesses
• Operating pressures and provision of
safety devices e.g..
• Safety valve (PRV)
• Gauges
• Level Controls
• Blow down valves
• Pressure gauges
LPG in cylinders
precautions
(storage)
Control of ignition sources
• No smoking
• Storage of cylinders away from
potential ignition sources e.g..
fabrication shop
• Control of mobile phones
• Storage area regarded as zone 2
so only zone 2 IS rated electrical
equipment to be used
• Signage stating highly flammable
• Dry powder fire extinguisher
located close to storage area
Concrete level floor, surrounding
area kept free of vegetation (not
with use of oxidising week killer
e.g.. sodium chlorate
Stored away from excavations,
drains, pond, rivers, cellars at least
3 m
Cylinders stored in upright position
Stored away from any oxygen
cylinders. oxidising substances
Empty cylinders stored separately
from full cylinders, caps fitted to
valves. Well ventilated
Protected from elements were
possible
If more than 400Kg stored must
have 2m high mesh fence and
cylinders at least 1.5m away from
fence with 2 exits
Any store room must be non-
combustible or fire resistant and
ventilated with and explosimeter
installed
Properties of LPG
• Flammable at standard temp &
pressure
• Denser than air
• Liquid form floats on water
• LEL is reached in small
concentrations
• Can cause suffocation in high
concentrations
Storage compound designed to
prevent vehicle impact
FLT safety
Causes of instability Lateral (side
instability)
• Insecure load
• Drive laterally on slope (angle of
slope, elevation of load
• Hitting obstruction e.g.. curb
• Uneven ground
• Cornering (fast, sharp)
• Poor tyre condition/uneven
pressures
Key points
• Instability
• Training
• Refresher training circumstances
Causes on instability Longitudinally
(Front to back instability)
• Overloaded vehicle
• Incorrect positioning of load on
forks
• Load slipping forward
(inappropriate tilt of mast
• Driving with load elevated
• Changing tilt
• Driving forwards down slops
• Driving backwards up slopes
• Sudden braking
• Striking overhead obstruction
Training
• Basic training (CITB/RTITB)
• Operating truck
• Maintenance & checks
• Specific job training
• Specific truck type operation
• Use of truck in various conditions
• Work to be undertaken & SSOW
• Familiarisation training under supervision
• Site layout
• Types of storage/load e.g.. racking
• Local emergency procedures
Refresher training appropriate
• Operator not used truck for some
time
• Been involved in accident/near
miss
• Developed unsafe practices
• Change in working practice
• Best practice every 3 years or as
per company policy
Methods and devices
designed to improve electrical
safety + precautions to be
taken when maintaining or
repairing systems
Fuse
• Protects systems not people normally
• Prevents overloads of electrical system
and overheating of electrical wiring
• Limits shock under severe fault
condition
• Limits over currents
• Does this by the heating effect of electric
current which melts the metal link if
current exceeds the design value
• Remains broken until replace
Miniature circuit breaker
• Close tolerances for design
current flow and speed of
operation
• Provide visual detection following
operation (e.g.. switch to off
position
• Need to be reset after fault
detection
• Are reliable
• Design to protect system
Reduced voltage system e.g.. 110V
• Transformer
• Supply centre tap to earth consist of
• Earthed systems
• Class 1 equipment
• Double insulated class 2 equipment
• Required procedural measures to be followed
Precaution to be taken when maintaining
or repairing electrical systems
•Identify equipment to be worked on
•Obtain system drawings & information
•Consider whether work can be done
dead SSOW for dead:
• Isolation/lock off
• PTW
• Proved dead
• Test test equipment
•If work required is live SSOW:
• Screening of conductors near
work
• Testing live conductors through
holes with probes
• Use of suitable test equipment
• Have testing arrangements in
place for testing equipment
• Consideration of accompaniment
• Consideration of insulated tools
• Adequate space
• Adequate lighting
Residual current devices or earth leakage
circuit breakers
•Shock limiting device not system
protection
•Shock is still received but time reduced
•Monitors balance of current in line and
neutral
•Operates on earth leakage fault
•Live and neutral disconnect from local
power supply
Key points
• Fuses
• Miniature circuit breakers
• Residual current devices
• Reduced low voltage systems
• Precautions to be taken
Safety provisions required for
receiving and storing acids and
alkalis
Operation
• SSOW
• Operation of equipment
• Emergency procedures e.g..
spill response
• Training
• Tanker drivers
• Operators
• Provision of PPE e.g.. chemically
resistant suits, gloves, full face visor
Maintenance
• Arrangements for examination and
inspections
• PTW system
• Isolation procedures
• Cleaning prior to work e.g.. purge
• Regular cleaning of bunds
• Provision of training to maintenance
staff both maintenance and
emergency
Design
• Material to be used for vessels and
pipework
• Suitable to withstand corrosive
nature of substances
• Layout of facility
• Segregation between acid/alkalis
e.g.. compartmentalisation
• Design and position of inlets
• Prevent cross connection
• Bunding of tanks
• Separate bunds
• Capacity 110% of largest container
min
• Bunded sealed with appropriate
material (with stand corrosive)
• Safety devices
• High level indicators
• Isolations
• PLC control
• Interlocked system
• Adequate lighting
• Adequate access and egress
• Arrangements for spill containment
• Labelling of system e.g.. flow direction of
pipes
• Emergency arrangements e.g.. drench
water safety shower
Runaway reactions
Temperature Increase speeds up
reaction – Le Chateliers principle
If the heat released from reaction is
not controlled/removed reaction will
speed up exponentially
Can result in
• auto ignition explosion
• Catastrophic over pressure
resulting in loss of containment
e.g.. vessel rupture and toxic
release
• Violent boiling
• Secondary competing reaction
Operational features to prevent
• High calibre of operator experienced
and appropriate level of qualification
to operate process
• Ensure that maintenance
activities/raw material handling don’t
introduce potential catalysis into
reaction
Design features to prevent
• Conduct HAZOP study
• Appropriate temperature control system
e.g.. matrix cooler
• High integrity temperature detection linked
to cooling/reaction addition protection
• Pressure rise detection linked to
cooling/venting/auto shut down
• Vessel protected by correctly sized bursting
disc linked to safe haven e.g.. secondary
vessel to dump reaction to
• PRV’s, weighted lids to realise pressure
• Agitation of liquids to promote even temp
distribution
Causes
• Failure of temp control (reaction
cooling)
• Strong exothermic reaction
• Presence of containment catalysis
(speeds up reaction)
Chemical changes involve heat
• Exothermic - Evolutes
• Endothermic - Absorbs
BLEVE
Cylinder/container containing
flammable gas under pressure e.g..
butane pressure turns gas into
liquid state
Valve opened reduces pressure
turning liquid into gaseous state
Cylinder exposed to heat source
e.g.. caught in a fire liquids absorbs
heat
Area unable to hold internal over
pressure and ruptures
Area of cylinder just above liquid
level starts to weaken/thin with heat
Liquid level falls heat continues
Liquids starts to vapour and is
vented off
Sudden release of contents
resulting in
•Blast wave (low)
•Radiation (thermal) high
•Missiles travelling long distances
Substantial thermal heat sever
burns e.g.. LPG cylinder BLEVE has
serve burn range of 35m
Examples of incidents
San Carlos
• Crashed over loaded road tanker
• Explosion
• 216 Dead
Mexico city
Reducing cost and
environmental impact
of hazardous waste
(sludge)
Identify recycling opportunities at
all stages of process
Substitute process materials for
ones that give rise to non
hazardous waste
Improve production efficiency to
produce less waste
Exchange waste streams to other
companies which could use waste
as raw material e.g.. waste solvents
to paint producers
Selection of waste contractors that
can process the waste
Treat waste to reduce hazardous
properties e.g.. ph balancing
Treat waste on-site to reduce
quantity (De-watering)
Explore other disposal means
(incineration, liquefied waste to
sewer)
Explore becoming licensed to save
cost e.g.. EA permit
Last paper
NDT
Dye testing
• Put dye on
• Dye penetrates making cracks visible
• Cheap & simple (pro)
• Doesn’t detect sub surface faults
(con)
• Not totally reliable (con)
• Can be enhanced by using
fluorescent penetrate and UV source
• Penetrate may be toxic (con)
• Need good eyesight
Impact (tap testing)
• Strike surface
• Changes in pitch of reverberant
sound
• Cheap (pro)
• No indication of where fault is
located (con)
• Relies on individual skill (con)
Radiography
• X-rays/Gamma rays penetrate item and
leave an image on film
• Defects are shown up by differences in the
intensity of the radiation striking the film
• Detects internal defects and a permanent
record is created
• Expensive
• Bulky equipment
• Present radiation hazard and tight controls
are required
• Skilled radiographers are needed
Eddy current testing
• Surface and near surface crack detection
• Electromagnetic method/instrumentation
• Can be used to verify materials heat treat
condition
• Can be automated (pro)
• Can suffer from spurious defect
indications
• Doesn’t work on non-conductive materials
• Relatively expensive and requires skilled
operator
Magnetic particle
• Coat surface with magnetic power
or liquid
• Simple & Quick
• Very sensitive to surface cracks
• Interpretation of results can be
difficult particularly on inside of
vessel
Ultrasonic Technique
• Short pulses of high frequency
ultrasound are used
• Reflected waves detected and shown
on digital display or oscilloscope
• Surface and sub-surface defects
• Only requires one side of joint
• Quick to perform
• Suitable for most environments
• High level of expertise required
• Coupling equipment onto rough
surfaces can be difficult
Other techniques
• Pneumatic testing
• Hydro testing
Purpose
Check for faults (e.g.. cracks) in
components before they develop
into total failure without affecting
integrity of the component
H & S Issues to identify
during a lighting audit of a
factory
Availability of natural light
Compliant with workplace (health,
safety & welfare) regs
Requirements for pedestrians/vehicles
Avoidance of glare
DSE work station lighting
Task specific lighting
Close working tasks
Avoidance of stroboscopic effects
with regard to rotating machinery
Emergency lighting
Illumination ratio
Equipment lighting to comply
with PUWER requirements
Maintenance, cleaning and
testing considerations
Level of luminance
Lighting fort non-daytime
external areas
Psychological effects
Consideration of flammable
atmospheres etc EX rating
Safety aspects to consider
before starting external
maintenance/construction
works on build with public
facing front (footpath) work includes roof
Access & Egress
• Maintenance workers
• Pedestrians
• Building workers
• Vehicles
Public safety
• Falling objects
• Screening
• Segregations/barriers
• Security
• Fencing
• Dust damping
• Noise levels
Welfare facilities
• Washing
• Toilets
• Rest/eating etc
Plant and equipment requirements
• Suitability
• Availability
Building workers safety
• Safe systems of work
• Provision of PPE
• Fall protection
• Scaffolding
• Edge protection
• Signage
• Hazardous materials present e.g.
asbestos
Emergency arrangements
• Alarm
• Muster points
• Escape routes
Storage of materials
• Hazardous
• Flammable
• Housekeeping
• Lay down areas
Traffic management
• Deliveries
• Plant
• MEWPS etc
Factors that could
contribute to a delay in
evacuation + benefits
of regular drills
Fire Alarm Design/maintenance
• Quiet
• Does not extend into all parts
of building
• Poorly maintained sounders
• Faults within infrastructure
leading to partial failure in
some areas
Deficiencies in procedure
• Difficult to understand
• Poorly communicated
• Not exercised
• Poorly planned escape routes
• Untrained staff
Execution of procedure
• Delayed response to alarm
• Staff not reacting quickly
• Finishing of phone calls
• Switching off equipment
• Fire Marshalls not following
procedure
• Blocked escape routes
• Staff not trained
• Poor response perhaps many
false alarms have occurred in past
Human factors
• Hearing disabilities
• Belief that false alarm
• Belief that above evacuating
• Waiting for direct notification
e.g.. phone call
• Routine violations
Benefits of regular drills
• Compliance with legal
requirements FFRO
• Efficient evacuation in future
• Highlights deficiencies in alarm,
procedure and evacuation
• Allow practise of scenarios such
as abnormal normal route use etc
• Refresh staff training and
awareness of procedure
Introduction of Automated Guided Vehicle to
Warehouse
Risks Reduced
• Manual handling
• Pedestrian/vehicle collision
• Racking Collisions
• Falling objects less likely to
contact person
• WAH access to racking
• Reduction of noise
• FLT collisions
• Incorrect order picking
Risks Increased
• Programming dangers (teachers)
• Interference in signal
• Proximity sensors to prevent
pedestrian contact
• AGV collision
• Guarding of order picking
machinery
• Dropped loads to be dealt with in
automated area
• Maintenance activities for
equipment
• Software failure
Precautions to be
taken before &
during repair work
of a 15m high grain
silo on farm (with
welding required)
Planning & Organising
• Consider work to be carried out
and devise RA & MS
• Nominate supervisor for task
• All workers briefed on general &
specific risks
• Suitable equipment for task e.g..
PPE, tools, access etc
Preparation of Silo
• Emptied
• Locked off to prevent filling
movement of parts
• Residue removed before hot
works
• Damped down
• Signage erected of work in
progress etc
Working area
• Excluding non essential personnel
• Erecting barriers
• Sighting of warning signs
Working at height
• Use of platforms
• Handrails
• Toe boards
• Harnesses if required
• Protection of fragile sections of
silo top
Confined space entry
• PTW control
• Ventilation
• Trained staff
• Emergency rescue plan defined
and trained
• Ensure suitable access and
egress
• Oxygen monitoring
MEWPS
Hazards
• Falls from height of persons/materials
• Instability of vehicle e.g.. uneven ground
• Being struck by other vehicles
• Trapping & impact hazards
• Mechanical failure
• Contact with over head power lines
• Exposure of workers to adverse weather conditions
Requirements for safe use
• Selection of trained competent operators
• Persons may be connected to MEWP with fall restraint
• Toe boards installed/use of tool wrist straps
• Barriers installed to protect area MEWP used in
• Correct positioning e.g.. level firm ground, not close to over head services, use of outriggers where installed
• Prevent of use in adverse weather conditions
• Not exceeding SWL
• Regular inspections & maintenance
• Ensure trap points are guarded
• Ensure used in locked position
• Prohibit transfer of people/materials whilst in raised position
To supply machine
under SMSR1992
process
Satisfy Essential health and safety
requirements and be safe
•Safe and reliable control devices
including normal operation and
emergency controls
•Stable
•Protection against mechanical
hazards e.g.. moving parts guarded
•Protection from other hazards e.g..
vibration, electricity & noise
•Maintenance activities
•Adequate indicators e.g.. alarms
and warning light etc
Preparation of technical file
•Detailed drawings
•Calculations, test reports
•Description of methods used to eliminate
hazards
•Machinery RA
•Instruction draw up in accordance with
provision of information
Satisfy requirements of
EHSR
Responsible person to
prepare technical file
Responsible person to
ensure machine meets
requirements of other
EC directives
Issue a Declaration of
conformance
Fix the CE mark in a
visible, legible and
obvious manner Last paper
Factors to consider
when devising
scheme for PAT
testing
Inventory of all equipment
requiring examination and
test to be made and unique
means of identification
e.g.. number system
Determine appropriate
frequency of inspection for each
item based on factors affecting
level of risk e.g..
•Type of appliance
•Protective systems used
•Use
•Frequency of movements
•Earth boning
•Age
•Environment which appliance
used in
•Experience and competence of
user
•Historical information and
manufacturers
recommendations
Electricity at work regs and HSE
published guidance
Criteria for each type of
examination defined including
issues such as
•Competence of the tester
•Calibration and maintenance of
test equipment
•Format of records to be kept
•Results of tests and
examinations
•Systems to identify and remove
from use equipment that is
found to be faulty
Sources of Ignition from diesel powered vehicles and possible protection to
minimise risk of explosion in flammable atmosphere
Sources
• Flames/sparks from exhaust/inlet systems
• Sparks from vehicle electrical system
• Static build up from over speeding/loading the engine
• Hot parts e.g.. exhaust
Protection
• Fit spark/flame arrestors preventing flashback to atmosphere if drawn into inlet system plus prevent any sparks from escaping system
• Engine and exhaust system design to ensure surface temps are below ignition temp of atmosphere
• Use of water jacket around hot parts
• Electrical equipment on vehicle suitable for zones 1 or 2 where possible
• Speed limiters to prevent speed at which static could build up
• Use of electrically conductive materials for parts e.g.. tyres to reduce static build up.
Key safety features
of building used to
store highly
flammables
Bunding to contain spills
Facility to collect & dispose of
spillages e.g.. spill kit
Building constructed of fire
resistant materials
Adequate distance from other
buildings Impermeable floor
Mean of segregation of materials
e.g.. low walls/dividers, cabinets
Roof lightweight and/or blast panels
High and low level ventilation
Adequate access and egress e.g.. 2
points of entry/exit including ramp
to facilitate drum handling
Security features such as locks,
alarms, and signage
Emergency lighting/appropriate EX
rated electrical equipment e.g.. zone
2 rated lights
Sprinkler systems/fire extinguishers
Design factors to
consider when
providing a sprinkler
system
Capacity of water required and
adequacy of existing supply
Design of pump system e.g..
diesel back up if electrical pump
installed
Means of activating system
(fragile bulbs or detector
activated
Presence of substances which
react violently with water
Area to be covered
Spray pattern required
Linkage of system to alarms
Height of any storage racking
and distance from sprinkler
heads, possible protection from
vehicle movements e.g.. FLT
tines
Provision of fire stopping water
curtains to prevent fire spread,
compartmentalisation
Provision of water run off
Provision required for testing
and maintenance
Possible mechanisms of structural failure of
building during storm
• Adverse weather conditions
exceeding designed wind loading
capacity of structure
• Excess weight on roof caused by
rain water or snow
• Weakening of steel structure by
corrosion through roof leaks
• Inoperation of rainwater drains
• Alterations to structural members
which have invalidated original
design calculations
• Subsidence or nearby
tunnels/excavation leading to
foundation instability
• Vibration caused by traffic etc
leading to structural fatigue
• Inadequate design and/or
construction of structure
H & S issues to be
considered when
planning demolition
of building
Notification of HSE under CDM 2007
regs
If building partially collapsed
already devise method for
demolishing to avoid premature
collapse of the remainder
Protection of nearby
buildings/business/properties
Selection of and Inspection,
maintenance of plant and
equipment to be used
Identification of buried and/or
overhead services e.g.. power
cables, gas pipelines
Precautions to prevent people or
objects falling e.g.. scaffolds, edge
protection
Protection of public e.g.. barriers,
signs, security
Identification of competent
demolition contractors
PPE required for workers e.g.. hard
hats, ear protections safety boots,
protective clothing, eye protection
etc
Site traffic management if required
Welfare facilities provision e.g..
toilets, wash and rest facility plus
maybe lay down area for
contaminated clothing
Control of noise
Identification of hazardous
materials, control of dust and safe
removal of waste from site – use of
licensed carrier etc
Factors that cause instability of mobile cranes and measures to be
taken to reduce likelihood of overturning during operation
Causes of instability
• Incorrect selection of crane e.g.. SWL to low
for lift
• Incorrect sling of load
• Unstable ground incapable of bearing weight
of crane and load
• Uneven/sloping ground
• Obstructions being struck by crane of things
striking crane e.g.. other plant of site
• Exceeding SWL of crane of lift tackle
• Inoperation of crane e.g.. incompetent,
inexperienced operator, not using out
riggers
• Poor lift control by AP/banksman.
• Unsuitable lifting plan
• Mechanical failure
• Adverse weather condition e.g.. wind
• Lack of maintenance of crane e.g.. incorrect
tyre pressures, rope not inspected etc.
Measure taken to avoid
• Conduct full assessment of lift required and
surrounding areas including establishing the
load bearing capacity of the ground that the
crane will operate on
• Define and implement sufficient lifting plan
use of competent appointed person
• Selection of appropriate crane for lift
• Ensure that maintenance and testing of
crane is adequate
• Appoint competent person to supervise lift
i.e.. appointed person, competent banksman
• Engineering controls e.g.. ensure that
outriggers are used and fully extended
where appropriate, ensure that capacity
indicator and alarms are functional
• Ensure that the motion and performance
limit device are in working condition
• Behavioural controls such as competence
and training of driver, slinger and banksman
Last paper
Precautions to be
taken when working
near an overhead
electrical supply
Explore possibility of re-routing
cables or making dead
Consult with utilities supplier before
taking any protective measures
Identification of safe working
distance i.e. 9 m if wooden or steel
poles 15m if pylons plus length of
jib or boom if cranes/excavators are
to be used
Safe systems of work to be defined
and implemented
Height restrictions on plant
Use of goal posts and/or tunnels
Use of barriers, marking tape and
bunting
Supervision and hazard awareness
training for workers e.g.. toolbox
talk on hazard associated with cable
and what measure need to be taken
to avoid
Warning signs and protection for
public if necessary
Precautions to ensure
safe provision & use of
electricity on construction
site (feed taken from
overhead lines)
Planning and assessment for
development of electrical supply by
a competent person
Safe positioning of transformers
e.g.. protection from plant/vehicle
impact, barriers to prevent workers
accessing area
Routing, marking and protection for
cables
Development of safe systems of
work
Arrangements for testing and
maintenance of portable equipment
Arrangements for inspection and
maintenance of the fixed supply to
include earth bonding checks
Use of protective devices e.g..
reduced low voltage systems (110),
RCD’s and double insulated
equipment
Use of competent persons for
installation work of electrical supply
Component failure
Fatigue failure
• Crack propagation from points of stress concentration
(e.g.. groves, weak weld points), fluctuating stress final
failure may be ductile or brittle
• Factors contributing
• Surface occlusions/damage
• Choice of material
• Residual stress imposed through manufacture
• Corrosion, temperature
• Measures to take to prevent
• Design spec appropriate
• Quality assurance on manufacture
• Assembled according to spec
• Correct use – avoid misuse e.g.. over ,loading
• Maintenance/testing NDT
Buckling (Compressive force)
• Buckling – yield of one side of
structural member under axial
compressive loading
• Factors contributing
• Excessive/non uniform loading
• Weakening due to removal of
cross members
• Use of out of true members e.g..
scaffold tube at incorrect angle
i.e.. not 90 under load
• Excessive temperature
• Measures to be taken to prevent
• Design/material selection
• Avoid overload work within spec
• Temp control
• Maintenance/testing NDT
Ductile Failure (stretch)
• Ductile failure in metals occur when the yield stress of the
material has been exceeded by the material being placed in
tension (stretched). The metal moves from it’s elastic region
into it’s plastic region and loses its shape. There is a
reduction in cross sectional area at failure point. The failure
will appear as a ‘cone / cup’ at 45 degrees to the load along
the grain boundaries
• Factors contributing
• High temperature
• Over loading
• Design inappropriate
• Measures to be taken to prevent
• Temp control
• Selection/design of materials
• Maintenance/testing
• Operate within spec limits of equipment
Creep
• Gradual yielding of material under stress close to elastic
limit (undergoes plastic deformation
• Factors contributing
• Continuous loading
• High temp e.g.. hot pressurised pipes, turbine
blades
• Overloading
• Design spec etc
• Measures to be taken to prevent
• Temp control
• Selection/design of materials
• Maintenance/testing
• Operate within spec limits of equipment
Brittle failure
• brittle fracture, no apparent plastic
deformation takes place before fracture
Factors which promote brittle fracture
• Low temperature
• Inherently brittle material (cast iron)
• Impact or snatch loading (does not give
material time to react
Gamma
Radiography
Gamma radiography uses the transmission of gamma
rays from a sealed ionising radiation source (isotope)
through a test object onto a film placed on the opposite
side. The film records the intensity of the radiation
received and since cracks and flaws are hollow, a
greater intensity of rays pass onto the film showing up
defects as darker regions
Advantages
Permanent record produced.
• Can be used to test most materials
• Internal defects can be identified
• Coupling with the surface of the test
piece is not required
Disadvantages
• Poses a radiation exposure hazard to operators requiring
specific SSOW to be implemented
• Can be time consuming due to application to HSE each time
test is required
• Equipment can be bulking and difficult to move
• Specialist operators are required and staff to interpret results
• Results may take a long time to receive
• Can be an expensive process to run
Sources of specific pollutants likely to be associated with a multi-fuel CHP
power stations using either coal, oil or gas for burning under normal operations
and foreseeable abnormal operations (located on river estuary taking deliveries
by ship, road & pipeline) plant also has water treatment plant
Normal operations
• Emissions to air – Carbon monoxide & oxides of
nitrogen from burning of fossil fuels
– Sulphur dioxide/sulphur compounds when coal or oil is burned
• Other pollutants – Soot & coal dust from
incomplete combustion
– Solid waste from coal & oil ash
– Acid & alkali effluents from water treatment process
– Emissions from vehicles delivering fuel to site same for ships
Abnormal operations
• Leaks – Oil storage tanks
– Gas supply pipelines
– Acid/Alkali storage tanks
• Spillage of chemical from road tank accident
• Oil slicks from ships during offloading or major disaster e.g.. sinking
• Fire leading to fire water run off during fire fighting
Factors to ensure
safe use of FLT
man basket
Design of basket
• Constructed for task
intended
• Not exceed the width of FLT
• Toe boards/guard rails
installed
• SWL indicated on basket in
either weight or no. of people
possible to carry, not
exceeding 50% of FLT SWL
• Guards fitted to protect
against moving parts of FLT
e.g.. chain
Basket maintained and inspected at
least every 6 months
FLT to be parked on firm, level
ground, brake applied, driver in
truck Competent FLT driver
Anchorage point in cage and
harness fitted and connected to
persons in basket
Barriers positioned around work
area preventing collision from other
vehicles and protect others against
falling objects from basket
Cage securely fixed to forks and
truck not moved during activity
Trained and competent operator in
basket, aware of hazards associated
with use
A petrol storage tank in a bund containing three similar tanks is overfilled
resulting in a large spillage of petrol into the bund. The petrol vapour exploded
Design & construction measures to prevent such an incident
• Adequate segregation between adjacent tanks
• Separate bunds for each tank
• Interlocked pumping system with high level alarms min double redundancy of alarms
• Level detection
• Vapour detection system fitted in bunds
• Remote shut down system
• Good earth bonding
Measures to mitigate the effects
• Fixed foam installations capable to spray the surface of pool in the bunded areas
• Installation of foam monitors capable of reaching top of tanks
• Radiation walls between tanks/bunds to prevent other tanks from being heated
• Adequate supply of fire water
• Installation of remote pumps to empty affected tanks
• Easy route of access for fire fighters
• Provision of drainage interceptors to minimise enviro affects of fire water run off
• Regular draining and cleaning to remove rainwater from bunds
• Provision of site based emergency response team.
Fixed guards factors to
consider in design and
use to ensure people are
adequately protected
Design
• Material of construction sufficiently
robust to withstand workplace
rigours and contain any ejected
materials
• Should allow sight of process if
required
• Method of fixing should require
special tool to removed e.g.. torque
bolts
• Ensure that any necessary
openings provide enough distance
from hazards to prevent harm
• Guards reverberation exacerbating
noise problems
Use
• Monitoring and supervision to
ensure guards are not
removed/tampered with
• SSOW fir carrying out
maintenance operations with
guards removed
• Guard check procedure to ensure
guard is kept in maintained
condition
• Provision of information and
training for operators and
maintenance staff detailing the
hazards associated with guard
defeats and other SSOW
Fixed guard
Defined in BSENISO12100 as a guard fixed in
such a manner (e.g.. by screws, nuts, welding)
that can only be removed or opened by the use
of tools or destruction of the affixing means. It
provides protection against mechanical hazards
when infrequent or no access is required during
normal operation of the machine. Acts as a
fence between people and dangerous machinery
parts
Fixed electrical systems faults (including corrosive atmospheres) & Information
relating to system that electrician would need before conducting a survey of
system
Type of faults found in fixed electrical
system (including systems in area with
corrosive atmosphere
•Poor earth bonding
•Damaged sockets and switchgear
•Covers missing from junction boxes
•Incompetent workmanship and
inadequate excess current protection
•Exposed conductors due to damaged insulation
from corrosive
•Short circuits caused by ingress of fluids
•Corrosion of system parts
•Unsuitability for use in wet & corrosive
conditions
Information needed by electrician before
conducting a survey
•Type of equipment and its rating (operating
voltage and current)
•IP classification (including measure of protect
against ingress of water
•Circuit diagrams and/manuals for the equipment
•Details of any modifications made
•Means of isolations and location
•Earthing arrangements
•Type and size of cables
•Details on the operations of protective devices
•Copies of previous inspection reports and
repairs made/maintenance carried out
Robots, implications for safety and how risk to personnel can be reduced when
working with
Features of industrial robots that may have particular implications for safety
•Sudden, rapid or unexpected movements
•Aberrant behaviours e.g.. robot moving outside normal operating parameters
•Dropped loads or ejected materials people have to enter area to rectify
•Software problems which are difficult to detect
•Dangers associated with teaching robot e.g.. may require close work with robot moving
•Dangers from work being carried out e.g.. spot welding, stored energy
•Dangers arising from maintenance activities e.g.. working in area close, robot may continue working
•Failure of perimeter sensors leading to robot collisions with people or other equipment
Reducing risk to personnel working in vicinity or with robots
•Conduction risk assessment to identify hazards associated
with robots and those at risk, evaluate the risk and identify
controls required to reduce the risk to an acceptable level
(eliminate or reduce)
•Restricting access by fixed fencing
•Provision of interlock access point e.g.. pressure mats
•Installation of light sensors e.g.. curtain or eye to detect
motion and stop robot (automatic guarding)
•Provision of mechanical restrains
•Use of audible start up warning
•Procedures for restarting after interruption
•Emergency stop systems
•Introduction of safe systems of work e.g.. isolation lock out
tag out before maintenance activities commence
•Training relevant people in hazards associated with robot and
precaution necessary
•Introduction of monitoring system including audit and the
keeping of records of maintenance and defects
•Maintenance program
•Routine guard checking procedure
Robots, implications for safety and how risk to personnel can be reduced when
working with
Features of industrial robots that may have particular implications for safety
•Sudden, rapid or unexpected movements
•Aberrant behaviours e.g.. robot moving outside normal
operating parameters
•Dropped loads or ejected materials people have to enter area
to rectify
•Software problems which are difficult to detect
•Dangers associated with teaching robot e.g.. may require
close work with robot moving
•Dangers from work being carried out e.g.. spot welding,
stored energy
•Dangers arising from maintenance activities e.g.. working in
area close, robot may continue working
•Failure of perimeter sensors leading to robot collisions with
people or other equipment
Reducing risk to personnel working in vicinity or with robots
•Conduction risk assessment to identify hazards associated
with robots and those at risk, evaluate the risk and identify
controls required to reduce the risk to an acceptable level
(eliminate or reduce)
•Restricting access by fixed fencing
•Provision of interlock access point e.g.. pressure mats
•Installation of light sensors e.g.. curtain or eye to detect
motion and stop robot (automatic guarding)
•Provision of mechanical restrains
•Use of audible start up warning
•Procedures for restarting after interruption
•Emergency stop systems
•Introduction of safe systems of work e.g.. isolation lock out
tag out before maintenance activities commence
•Training relevant people in hazards associated with robot and
precaution necessary
•Introduction of monitoring system including audit and the
keeping of records of maintenance and defects
•Maintenance program
•Routine guard checking procedure
Scaffolding, factors causing instability and principles of design and erection to
ensure stability
Factors that cause scaffolds to become unstable/collapse
•Scaffold not erected as per original design
•In-competent scaffold designers/erectors
•Ground constructed on not being of load
bearing capacity
•Scaffold foundation being undermined by
surface water or site works e.g.. excavation
•Incorrect use of fittings and/or use of
damaged fittings
•Standards were out of plumb or bent
•Unauthorised/malicious alterations by
incompetent people
•Overloading of scaffold e.g.. material
storage
•Impact e.g.. load suspended by crane/hit by
plant vehicle
•Severe weather e.g.. excessive wind loading
Principles of design and erection to ensure safe/stable scaffold
•Use of competent persons
•Designed to withstand required loading
•Constructed of sound materials & fittings
•Setting standards on base plates
•Ensure joints are staggered
•Fitting of longitudinal & diagonal bracing
•Ledger braces at every other pair of standards
•Vertical & horizontal ties no more than 8.5m apart and replaced by temporary ties if required to remove
•Scaffold erected in position where traffic/plant impact likely barriers should be erected (protection)
•Ground erected on to have suitable load bearing capacity
•Inspections carried out at regular intervals i.e.. not exceeding 7 days and after change in conditions e.g.. adverse weather conditions, after alterations etc.
•Do not load beyond design capacity
Pressure system
safety requirements
to be met before
commissioning
Siting of equipment to ensure
protection from vehicles
Separation from flammable
atmospheres
Protection of public from emission
of noise
Competent person to undertake a
pre commissioning check
Establish maintenance and
inspection procedures and written
scheme of examination defines
System design issues
• Adherence to standards
• Capacity
• Materials of construction
• Layout features
• Fitting of pressure gauges,
warning systems
• Relief valves and drain lines
• Marking of safety related info e.g..
safe working pressure
• Suitable guarding
• Certificate of conformity and CE
marked
Provision of information and
training for operators including
safety feature, limits and correct
operation of system
Pressure system
• Is a system comprising one or more pressure
vessels of rigid construction and any
associated pipe work and protective devices
• Pipe work with its protective devices to which a
transportable gas container maybe connected
• Pipeline and its protective devices which is
liable to contain a relevant fluid. i.e.. steam, gas
at a pressure greater than 0.5 bar above
atmospheric pressure when at a temp of 17.5 c
or a gas dissolved in solvent at ambient temp
which could be released from the solvent
without the application of heat
Trackers stability - will apply for most wheeled plant equipment
Factors that cause tractors to
overturn
•Angle of slope operated on too great
•Direction of travel on gradients
•Uneven or soft ground
•Speed of corner
•Condition and pressure of tyres
•Effects of trailers and other
attachments
•Power take of seizure
•Competence of driver
Minimising risk
•Restriction of use on steep gradients
•Operator training and awareness
•Correctly maintained tyres and pressure
•Fitting of wider tyres/additional wheels
•Fitting of counter balance weights
•Regular maintenance
•Power take of fitted with shearing pins
Limit effects of over turning
•Fitting and use of seat belt
•Roll over protection e.g.. cage protections
Computer Numeric control systems (CNC) fitted to lathe
Additional risks
•Increase in operation speed
•Increase in noise
•Possible unexpected movements
•Errors in programming and software
•Risk from teaching
•Risk from operator unfamiliarity
Minimising risk
•Risk assessment
•Fitting of fixed or interlocked guards to
prevent access during automatic cycle
•Provision of manual operation for setting
and cleaning operations e.g.. hold to run
system
•Relocation of controls out of danger zone
•Additional training for operators and
maintenance staff
•Updating of the instruction manual for
use, cleaning and maintaining the machine
•Conduct regular testing of the software
Investigation into
dust allegation from
local village that
dust is from plant
you work in
Conduct desk top survey (feasibility
study) involving residents look at
•Historical records
•Weather patterns
•Links with wind direction
•Identification of potential other
dust sources in area
Check plant for obvious faults and
conduct continuous monitoring
(background)
Check supervisor reports over
period of alleged fall out for
abnormalities in process/ check
maintenance logs for break down
e.g.. LEV systems
Consult and liaise with local
authorities/EA
Conduct analysis of dust collected
from village to establish if it
matches that produced from plant
Principle & Effect of
Vapour cloud
explosion
Confined e.g.. in a tank/vessel or
unconfined e.g.. petrol release
vapour cloud travelling Presence of flammable vapour at
concentration between LEL & UEL
Ignition source that exceeds the
minimum ignition energy required
Effects of VCE
• Vessel or containment rupture
resulting in rapid release of
liquefied gas
• Projectile materials
• Overpressure
• Thermal effects
Effects of explosions UCVCE
• Overpressure
• Thermal effects
• Emission of debris
• People and property damaged due
to pressure wave and thermal
radiation
Unconfined vapour clouds can
travel considerable distance before
igniting (find ignition source) or
may be dispersed to a
concentration below LEL depending
on conditions e.g.. wind speeds,
atmospheric pressure
Examples of VCE
• Flixborough 74
• Grangemouth
• Buncefield
top related