system for sliding door installation procedure · system for sliding door installation procedure....
Post on 22-Aug-2020
2 Views
Preview:
TRANSCRIPT
049900006 July 2014
®
SYSTEM FOR SLIDING DOORInstallation procedure
Features
• Realizedwithatelescopicguide,withhardenedtracksandsteelballsforbearing.
• Highreliabilityoftheslidingsystemduringtime.
• Reducedoveralldimensionsinsidethevehicle.
• Quickassemblyandeasyuse.
• Basedonadoorwithwidth900mm,maximumthickness85mm,maximumweight100kg.
• Forslidingdoorsfromrighttoleftandfromlefttoright
Picture1
®
1
Components of the kit
1 � N° 1 zinc plated plate
2 � N° 1 stainless steel lower rail
3 � N° 1 small limit stop plate
4 � N° 1 door block
5 � N° 1 stainless steel rail bar for the lower door
6 � N° 2 zinc plated linear guides
7 � N° 1 zinc plated telescopic guide L=900 mm
8 � N° 1 limit stop rubber
9 � N° 1 limit stop block
®
2
Assembly
Picture 2
The roof and the door must be properly reinforced with suitable plates where the fixing holes are located.
Assembly stages
®
3
1.FixingthetelescopicguideL900mm7onthedoorthroughcountersunkM5screws.
2.Fixingthelimitstopplate3onthedoorwithcountersunkM8screws(seepicture3).
3.Fixingthelimitstopblock9onthezincplatedplate1(seepicture4).
4. Fixingthesmalllimitstopplate3andthelimitstoprubber8onthezincplatedplate1throughacountersunkM5screw(seepicture3)
Picture 3 door completely opened
Picture 4 door completely open - detail of the limit stop block
®
4
Picture3doorcompletelyopened
Picture4doorcompletelyopen-detailofthelimitstopblock
5. Assembly of the zinc plated plate 1 to the telescopic guide 7 through countersunk M5 screws
Verifying the correct functioning of the system composed by the limit stop plate 3-limit stop rubber 8-door block 4
6. Fixing the rail bar of the lower door 5 onto the door through countersunk M8 screws
Picture 5 door completely open – detail on M6 screws on linear guides
5
®
7. Positioningofassembleddoorontothevehicletocheckthepositioningofthelinearguides.6
Itmustbeverifiedthatthelimitstopofthelinearguides 6 correspondstitheconfigurationofmaxcomingoutofthedoor.(picture5)
8. Fixing the linear guides 6 to the roof through countersunk M8 screws through a stop limit screw on the side of the door (picture 5)
9. Mounting the door on the vehicle through assembly of the zinc plated plate 1 to the linear guides 6 through M8 screws.
10. Fixing the stainless steel lower rail 2 on the external side of the body or the frame.
Verifying that the positioning of said stainless steel rail 2 is so that the door is maintained in vertical position and the limit stop is guaranteed when closing.
6
®
PASTORE & LOMBARDI S.p.A. con socio unico soggetta a direzione e coordinamento di HILBE S.p.A.
Via Don Minzoni, 340057 Cadriano di Granarolo Emilia (Bologna) - Italy
Capitale Sociale € 468.000 i.v. R.I. Bologna, C.F. e P.IVA 03276650375
R.E.A. della C.C.I.A.A. di Bologna 277528 Tel. +39 051 764111 - Fax +39 051 765414
info@pastorelombardi.comwww.pastorelombardi.com
®
top related