switching circuits composed of switching elements called gates that implement logical blocks or...

Switching circuits

• Composed of switching elements called “gates” that implement logical blocks or switching expressions

• Positive logic convention (active high):– High voltage or H Boolean 1– Low voltage or L Boolean 0

• Negative logic convention (active low):– Low voltage or L Boolean 1– High voltage or H Boolean 0

Switching circuits

• Logic variables inputs/outputs “signals”

• Signals “asserted” when the voltage level assumes the corresponding “1” value– Positive logic asserted by H– Negative logic asserted by L

• Logic variables are written complemented when they are active low– Active high signals: a, b, c– Active low signals: ā, ē, ū

Logic gates

• Logic gates switching functions• Gate symbols – two sets

Logic gates

• Gate symbols – two sets

Logic gates

• The NAND logic function and gate

Logic gates

• The NAND gate can be used to implement all 3 elementary operations of switching algebra: AND, OR, NOT

Logic gates

• The set {AND, OR, NOT} implements any switching function (by definition): it is functionally complete

• Therefore, the “NAND” gate can be used to implement any switching function– It is functionally complete, or “primitive”

Logic gates

• The NOR logic function and gate

Logic gates

• The NOR function can be used to implement all 3 elementary operations of switching algebra: AND, OR, NOT– It is functionally complete too

Logic gates

• The NOR logic function and gate

Logic gates and equivalence

• CMOS is “inverting” logic– NOR and NAND are easier to implement than OR

and AND– They are implemented as NOR or NAND followed

by an inverter

• More than one representation is possible for the same switching function

• Different circuits of logic gates might perform the same switching function– Simpler networks are preferable– Need to analyze for equivalence and transform

Logic gates and equivalence

• Equivalent logic networks

Logic gates and equivalence

• Proving the equivalence

Digital circuits

• Analysis– Given a circuit, abstract the Boolean function it is

implementing and try to improve the implementation or verify the function• From gate diagrams• From timing diagrams

• Synthesis– Given a switching function, obtain the

corresponding switching network

Analysis

• Timing diagram

Analysis

• Truth table

Analysis

• Switching network

Combinational analysis

... derives truth table

Signal expressions

Multiply out:F = ((X + Y) Z) + (X Y Z) = (X Z) + (Y Z) + (X Y Z)

New circuit, same function

F = ((X + Y’)Z) + X’YZ’Note: [X’YZ’]Z = 0 (X + Y’)X’YZ’ = 0 (X’YZ’)(X’YZ’) = X’YZ’So, F = [(X + Y’) + X’YZ’][Z + X’YZ’] =(X + Y’ + X’)(X + Y’ + Y)(X + Y’ + Z’)(Z + X’)(Z + Y)(Z + Z’) =(1)(1)(X + Y’ + Z’)(X’ + Z)(Y + Z)(1) = (X + Y’ + Z’)(X’ + Z)(Y + Z)

Circuit:

Any number of manipulations can yield equivalent circuitse.g.

Push bubbles to obtain cancellations

Push bubbles to obtain cancellations

Conclude:given circuit ==> many equivalent equations

circuit does not determine equation

Two-level AND-OR

Three-level equivalent

Two-level NAND-NAND

Also, equation does not determine circuit:

Combinational analysisgiven circuit, determine function

Combinational synthesisgiven function, determine circuit

Prime number detector: F = (1, 2, 3, 5, 7, 11, 13)

AND-OR design'' 0033 NNNN

Derive truth table or expand:

A = P + E EX’ (W D G)’ = P + E EX’ (W’ + D’ + G’)= P + E EX’ W’ + E EX’ D’ + E EX’ G’

Alarm:

A = P + E EX’ W’ + E EX’ D’ + E EX’ G’

NANDs, NORs have fewer transistors than ANDs, ORsAND-OR converts readily to NAND-NAND

Complication if some inputs go directly to second stage:

OR-AND to NOR-NOR

Bubble-pushing produces non-standard gateSolution: inverters

Bubble-pushing produces non-standard gateSolution: inverters

Bubble-pushing produces non-standard gateSolution: inverters

Propagation delay

Propagation delay

Synthesis

• SOP functions -> AND – OR networks• POS functions -> OR – AND networks• Not always possible to design directly

– Fan-in and out restrictions

• Most designs are modular and multi-level• Modern designs are too complex• Design and testing by computers

– VLSI - CAD

Logic simulation

• Two states only for an ideal logic signal– Two gates driving the same line in opposite

directions– Input left not connected or “floating”

• Third state ‘X’ is added to the set of states• Truth tables change

Synthesis approaches illustrated to this point:

Truth table derivation of minterms

Ad hoc construction of logic equation

Need systematic approach that minimizes hardware

Karnaugh maps

Quine-McCluskey algorithm