stabilising legs jockey wheels€¦ · jockey wheels econo movers stabilising legs bos stabiliser...
Post on 04-May-2020
10 Views
Preview:
TRANSCRIPT
T H E B O S R A N G E
www.bos370.com.au
6 Dunheved Circuit, St Marys NSW 276002 9623 6922sales@bos370.com.auwww.bos370.com.au
Like us on Facebook
BOS Jockey Wheels & Accessories Pty Ltd
JOCKEY WHEELS
ECONO MOVERS
STABILISING LEGS
BOS STABILISER LEGS
Out innovative range of products have been designed to make travel easy.You have been putting up with problems stabilising legs for decades because of limited alternatives.
The problems are:
• The load goes on the pin that holds the foot to the leg. This limits the load capacity to the strength of the pin AND that pin shears from wear over time, losing the foot and making the leg useless
• The release mechanism is stiff and hard to handle• The small footprint sinks into the ground if you don’t
use extra pads or blocks• A single pivot direction on the foot means you cannot
gain full contact on uneven terrain or slopes• They are too short so you need to carry blocks• You have to bend your back to wind a manual crank• It is a slow process, making setup take longer than
necessary
...the result is you put up with a NEAR ENOUGH IS GOOD ENOUGH level of… well… level!
We’ve addressed all of these issues and more to bring you the strongest, most ergonomic and EASY to use stabiliser legs on the market today from an Australian company you can trust to deliver service, quality and reliability.
See for yourself on:
CaravanersForum.comCaravanWorld.com.auMySwag.orgExpandasDownUnder.comFacebook.comAustraliaSoMuchToSee.comConquererForum.comForum.Australia4WD.comYouTube.com
™
9 REASONS YOU SHOULD CHOOSE BOS STABILISER LEGS
HOW TO CHOOSE YOUR BOS STABILISER LEGS
CHOOSE FROM 3 BRACKET OPTIONS
Purchasing a BOS Jockey wheel is an investment in saving you time and effort. Here’s why:
1. EASY – the patented BOS gearbox does all the hard work for you, eliminating strains; OR you can drive it with a drill
2. INNOVATIVE – the patented BOS PUSH/PULL handle makes release & positioning easy
3. POWERFUL – use 2 legs to lift your van or trailer off the ground to change a tyre. Each leg has a working load limit of 1,800kg (LMATS tested)
4. RELIABLE – weight is transferred to the base plate (NOT onto the pivot bolt)
5. VERSATILE – range of lengths to suit any rig – choice of different angle positions – extensions available for extra height when needed – large base plate can be angled & rotated for maximum
stability
6. QUALITY – Designed & manufactured in Australia using quality components
7. LOW MAINTENANCE – no servicing required; simply apply grease via the nipple when needed, and the internal dust boot keeps the inner tube clean
8. SIMPLE TO INSTALL – fits easily into pre-fitted brackets for drop-down legs
9. PEACE OF MIND – 2 year warranty• Consider the amount of lift required - 80, 155 or 215mm?• Consider your suspension type – limit straps recommended for independent suspension• While on level ground, measure distance from bracket to the ground
• These are sold in pairs. Measure front and rear (Note: this measurement can vary if your van is not level) Do you need different sizes? E.g. 500 for front and 600 for rear
• How will you install your legs?
440-041 440-051 440-061
All prices shown do not include delivery and are subject to change without notice. Please refer to bos370.com.au to confirm current pricing, or contact us for a quote.If you are not sure which is the best option for you contact us for help in making your choice.
For vans and trailers with a higher chassis, such as off-road, we recommend you purchase extensions if additional lift is required.
Retracted height: 400mm + 80mm lift = max. 480mm Retracted height: 500mm + 155mm lift = max. 655mm Retracted height: 600mm + 215mm lift = max. 815mm
Use your drill
Grease Nipples
Patented PUSH/PULL Handle
Weight on base plate
1. Bolt through 2. Weld on 3. Bolt over (100 or 150mm size)
Bracket
Ground
Measure while level
RRP
$350.00EACH
RRP
$375.00EACHRRP
$350.00EACH
top related