specifications guide - horizon hobby · en 2 specifications outside dimensions length width height...
Post on 16-Dec-2018
236 Views
Preview:
TRANSCRIPT
EN
1
SPECIFICATIONS GUIDE
EN
2
SPECIFICATIONS
OUTSIDE DImENSIONS
Length Width Height from Centerline Operating RPM
119mm 154mm with muffler 110mm 1,400–10,000
Displacement 20cc (1.20 cu. in.)
HP 2.1 hp @ 9000 rpm
Bore 32.0mm (1.26 inch)
Stroke 25.0mm (0.98 inch)
Complete Weight 41.6 oz (1.20 kg)
Engine-Only Weight 33.0 oz (0.93 kg)
Benchmark Prop 16 x 6 APC @ 9000 rpm
Prop Range 15 x 8–16 x 8
RPM Range 1400–10,000
38.50
25.00
56
14
69
EN
3
TORQUE
1.51.41.31.21.11.00.9
2.22.01.81.61.41.21.00.80.60.40.20.0OU
TPUT
(HP)
TORQUE (Nm)
(x1000RPM)
TORQUE
7 8 9 10 11 12
OUTPUT
35
108
64
119
34
110
84
58
EN
4
ExPlODED vIEw
REPlACEmENT PARTSNo. Item Number Description QTY
1 ZEN848EW012A1 CYLINDER 1
2 ZEN848EW014B1 GASKET 1
3 ZEN8488441800 BOLT 4
4 ZEN848EW014A0 INSULATOR 1
6 ZEN848EW02110 CASE COMP 1
7 ZEN848EW021D0 GASKET CASE 1
EN
5
No. Item Number Description QTY
8 ZEN115521240 BEARING 1
9 ZEN0603406001 BALL BEARING 1
10 ZENT160021240 BALL BEARING 1
11 ZEN0406502812 RING 1
12 ZENT160021210 SEAL 1
13 ZEN331072150 BOLT 4
14 ZEN848EW041A1 PISTON 1
15 ZENT207141210 RING 1
16 ZEN110141310 PIN PISTON 1
17 ZEN126041320 RING 2
18 ZEN550041410 BEARING 1
19 ZEN110141340 WASHER 2
20 ZEN848EW04200 SHAFT COMP 1
21 ZEN848EW042D0 KEY 1
22 ZEN114043250 SHIM 1
23 ZENP2001 PROP DRIvER 1
24 ZENP2002 PROP DRIvER SCREW 1
25 ZENP202603 PROP WASHER 1
26 ZENP202604 PROP NUT (8MM) 1
27 ZENP202627 IGNITION SENSOR WITH MOUNT 1
28 ZENPH01 M4x8 SCREW (2) 2
29 ZEN369992369 PLUG 1
30 ZEN848EW053x0 PLATE MOUNT 1
31 ZEN381954780 SCREW BZ0 4
32 ZENPEI10 ELECTRONIC IGNITION FOR 20CC CM6 PLUG 1
33 ZEN125230410 BOLT 1
37 ZEN848H7014C1 GASKET 1
38 ZEN848ES08300 FUNNEL 1
39 ZEN8488455000 BOLT 2
40 ZENP2005 MUFFLER 1
41 ZEN114013141 GASKET 1
42 ZENPH02 M5x12 SCREW (2) 2
EN
6
SPECIFICATIONS
OUTSIDE DImENSIONS
Length Width Height from Centerline Operating RPM
137mm 105mm 120mm 1,800–10,000
Displacement 25.4cc (1.55 cu in)
HP 2.4hp @ 8900 rpm
Bore 34.0mm (1.34 in)
Stroke 28mm (1.10 in)
Complete Weight 46.0 oz (1.30 kg)
Engine-Only Weight 37.3 oz (1.10 kg)
Benchmark Prop 16 x 8 APC @ 8,700–8.900 rpm
Prop Range 15 x 8–17 x 6
RPM Range 1,800–10,000
14
56
67
37.50
47
EN
7
TORQUE
2.72.62.52.42.32.22.12.01.91.81.71.61.5
2.01.91.81.71.61.51.41.31.21.11.0
OUTP
UT (H
P)TORQUE (Nm
)
(x1000RPM)7 8 9 10 11 12 13 14
TORQUE OUTPUT
96
120
70
116
43
64
137
34
EN
8
ExPlODED vIEw
REPlACEmENT PARTSNo. Item Number Description QTY
1 ZEN848ES512A0 CYLINDER 1
2 ZENT207513120 GASKET, BASE 1
3 ZEN331012281 BOLT 6
4 ZENT207513150 GASKET 1
5 ZEN114813162 INSULATOR 1
6 ZENT207514120 GASKET, CARBURETOR 1
EN
9
No. Item Number Description QTY
7 ZENT207521100 CASE-COMP 1
10 ZENT207521140 GASKET, CRANKCASE 1
11 ZEN216921210 REAR OIL SEAL 1
12 ZEN115521240 BEARING, CENTER 2
13 ZEN0406502812 CRANKSHAFT BEARING SNAP RING 1
14 ZEN0603406001 BEARING, FRONT 1
15 ZEN185021220 FRONT OIL SEAL 1
16 ZEN0125230530 CRANKCASE BOLT 4
17 ZENT208841110 PISTON 1
18 ZENT208841210 RING.PISTON 1
19 ZEN160041310 PIN 1
20 ZEN126041320 RING 2
21 ZEN550041410 NEEDLE BEARING 1
23 ZENP2623 ZP26 CRANKSHAFT COMPLETE 1
24 ZEN848ES553x0 PLATE MOUNT 1
25 ZEN0026210516 SCREW 3
28 ZEN100043240 KEY 1
29 ZEN114043250 SHIM 1
30 ZENPEI10A ELECT IGNITION FOR 26CC CM6 PLUG 1
31 ZENT207073110 SPARK PLUG RZ7C 1
32 ZEN0026330555 SCREW 2
33 ZEN114283110 SPACER 2
34 ZEN848ES08300 FUNNEL 1
36 ZENP2636 ZP26 CARBURETOR-A 1
37 ZENP2601 PROP DRIvER ZP26 1
38 ZENP2602 PROP DRIvER SCREW ZP26 1
39 ZENP202603 PROP WASHER ZP20/26 1
40 ZENP202604 PROP NUT (8MM) ZP20/26 1
41 ZENPH01 M4x8 SCREW (2) ZP20/26 2
41 ZEN114013141 GASKET 1
42 ZENPH02 M5x12 SCREW (2) ZP20/26 2
44 ZENP2605 MUFFLER ZP26 1
45 ZENPH01 M4x8 SCREW 2
46 ZENP202627 IGNITION SENSOR WITH MOUNT ZP20/26 1
ZENP2610 IGNITION RETAINING PLATE ZP26 1
EN
10
SPECIFICATIONS
OUTSIDE DImENSIONS
Length Width Height from Centerline Operating RPM
133mm 87mm 145mm 2,100–9,500
Displacement 38.0 cc (2.30 cu in)
HP 2.6hp @ 7200 rpm
Bore 38.0mm (1.50 in)
Stroke 33.0mm (1.30 in)
Complete Weight 57.0 oz (1.60 kg)
Engine-Only Weight 49.3oz (1.40 kg)
Benchmark Prop 18 x 10 APC @ 7,300 rpm
Prop Range 16 x 8–18 x 10
RPM Range 2,100–9,500
87
35
35
EN
11
TORQUE
2.72.62.52.42.32.22.12.01.91.81.7
2.01.91.81.71.61.51.41.31.2
OUTP
UT (H
P)TORQUE (Nm
)
(x1000RPM)6 7 8 9 10
TORQUE OUTPUT
14155
145
133
43
133
EN
12
ExPlODED vIEw
EN
13
REPlACEmENT PARTSNo. Item Number Description QTY
1 ZEN337812111 CYLINDER 1
2 ZEN333014111 INSULATOR 1
3 ZEN333014121 GASKET 1
5 ZEN333014132 GASKET 1
6 ZENP3805 MUFFLER ZP38 1
12 ZENP3813 MUFFLER BOLTS (M5x14 (2)) ZP38 2
13 ZEN337821110 CRANKCASE 1
14 ZEN0125230540 BOLT 4
15 ZEN0029220510 WASHER 4
16 ZEN312013510 PLUG 1
17 ZEN313013520 GASKET 1
18 ZEN334041113 PISTON 1
19 ZEN334041211 RING.PISTON 1
20 ZEN331042231 PIN 1
21 ZEN331041320 SNAP RING 2
22 ZEN114043250 SHIM 1
23 ZEN331042240 BEARING 1
24 ZENP3824 ZP38 SHAFT COMPLETE 1
25 ZEN0603006201 BEARING 2
26 ZEN165021220 SEAL 1
27 ZEN0406503212 SNAP RING 1
28 ZEN216921210 SEAL 1
29 ZEN126043240 KEY 1
30 ZENP3811 PROP DRIvER LOCKING NUT ZP38 1
31 ZENPH10 M8 SMALL SPRING WASHER 1
32 ZENPH11 16x8.4 FLAT WASHER 1
33 ZENP3801 PROP DRIvER ZP38 1
33 ZENPH08 PERMANENT MAGNET ø4x3 1
35 ZENP3803 PROP WASHER (2) ZP38 2
36 ZENP3812 M5x30 PROP SCREWS (4) ZP38 4
37 ZENPEI14 SINGLE IGNITION FOR 38CC RCJ7Y 1
38 ZENP3827 IGNITION SENSOR WITH MOUNT ZP38 1
42 ZEN369990032A G62/38/45/80T SPARK PLUG 1
43 ZENPH01 M4x8 SCREW (2) 2
44 ZENP3844 ZP38 CARBURETOR-A 1
44-1 ZENPH03 M2.5x4 SCREW/WASHER (4) 4
46 ZENP3809 MOUNTING PLATE ZP38 1
78 ZENPH02 M5x12 SCREW (4) 4
78 ZENPH09 M5 SPRING WASHER (4) 4
EN
14
SPECIFICATIONS
OUTSIDE DImENSIONS
Length Width Height from Centerline Operating RPM
150mm 140mm 135mm 2,000–8,500
Displacement 62.0cc (3.80 cu in)
HP 6.0hp @ 7200 rpm
Bore 47.5mm (1.90 in)
Stroke 35.0mm (1.40 in)
Complete Weight 72.0 oz (2.00 kg)
Engine-Only Weight 62.7 oz (1.80 kg)
Benchmark Prop 22 x 10 APC @ 7,800 rpm
Prop Range 20 x 8–22 x 10
RPM Range 2,000–8,500
95 99
135122
138
EN
15
TORQUE
6.5
6.0
5.5
5.0
4.5
4.0
3.5
3.0
4.0
3.5
3.0
2.5
OUTP
UT (H
P)TORQUE (Nm
)
(x1000RPM)6 7 8 9 10
TORQUE OUTPUT
4289
42
142
EN
16
No. Item Number Description QTY
1 ZEN336612116 CYLINDER 1
2 ZEN848C9014B3 INSULATOR GASKET 1
3 ZEN16210 INSULATOR 1
4 ZEN848C9014C2 CARBURETOR GASKET 1
5 ZEN261614211 CYLINDER BASE GASKET 1
6 ZEN331012281 CYLINDER BOLT 4
7 ZENP6205 MUFFLER ZP62 1
8 ZEN335615210 MUFFLER GASKET 1
9 ZENP6213 MUFFLER BOLTS (M5x12 (2)) ZP62 2
REPlACEmENT PARTS
ExPlODED vIEw
EN
17
No. Item Number Description QTY
10 ZENPH15 M5 SqUARE NUT 2
11, 12 ZENEP6212 ZP62 CRANKCASE COMP. 1
13 ZEN262921130 CASE PIN 3
14 ZEN0406503515 SNAP RING 1
15 ZENT401221240 BEARING 2
16 ZEN152021220 REAR OIL SEAL 1
17 ZEN140021220 FRONT OIL SEAL 1
18 ZEN262921311 CRANKCASE GASKET 1
19 ZEN335021320 CASE ASSEMBLY BOLT 4
20 ZEN261841112 PISTON 1
21 ZEN261841210 PISTON RING 2
22 ZEN336641310 PISTON PIN 1
23 ZEN335041320 PIN RETAINER 1
24 ZEN140041410 NEEDLE BEARING 1
25 ZEN261641510 CONNECTING ROD SPACER 1
26 ZENEP6226 ZP62 CRANKSHAFT COMP. 1
27 ZEN100043240 KEY 1
28 ZEN130042410 SHIM 2
29 ZENP628011 PROP DRIvER LOCKING NUT ZP62/80 (M10x1) 1
30 ZENP628001 PROP DRIvER ZP62/80 1
31 ZENP628014 SPRING WASHER (M10) ZP62/80 1
32 ZENPH14 SMALL WASHER 18x 10.5 1
33 ZENP628003 PROP WASHER (2) ZP62/80 2
34 ZENP6212 M5x30 PROP SCREWS (4) ZP62 4
36 ZENP6210 IGNITION RETAINING PLATE ZP62 3
37 ZENPEI13 ZP 62 IGNITION 1
38 ZENP628027 IGNITION SENSOR WITH MOUNT ZP62/80 1
42 ZEN369990032A G62/38/45/80T SPARK PLUG 1
43-1 ZENP6206 THROTTLE ARM ZP62 1
43-2 ZENP6207 THROTTLE SHAFT ZP62 1
43-3 ZENP6208 CHOKE CONTROL ARM ZP62 1
43-4 ZENP6209 CHOKE SHAFT ZP62 1
43-5 ZENPH03 M2.5x4 SCREW/WASHER 4
43 ZENP6243 ZP62 CARB ASSEMBLY 1
44 ZEN262982210 CARB MOUNT SCREW 2
45 ZEN6245 CARB WASHER 2
46 ZEN016020513 WASHER 2
48 ZENP6209 MOUNTING PLATE ZP62 1
49 ZENPH12 M6x14 SCREW 4
50 ZENPH13 M6 SPRING WASHER 4
EN
18
SPECIFICATIONS
OUTSIDE DImENSIONS
Length Width Height from Centerline Operating RPM
193mm 257mm 71mm 1,800–10,000
Displacement 80.0cc (4.88 cu in)
HP 7.4hp @ 7500 rpm
Bore 40.5mm (1.60 in)
Stroke 31.0mm (1.22 in)
Complete Weight 6.25 lbs (2.80 kg)
Engine-Only Weight 85 oz (2.40 kg)
Benchmark Prop 24 x 10 Mejzlik @ 6,800 rpm
Prop Range 22 x 12–24 x 10
RPM Range 1,800–10,000
125125
76 769798
2121
80
EN
19
7.57.06.56.05.55.04.54.03.53.0
7.06.56.05.55.04.5
OUTP
UT (H
P)TORQUE (Nm
)
(x1000RPM)6 7 8 9 10
TORQUE OUTPUT
TORqUE
12191
71
193
EN
20
REPlACEmENT PARTSNo. Item Number Description Qty
1 ZEN286912110 CYLINDER 2
2 ZENT208014110 MANIFOLD 1
5 ZENEP805 ZP80 CARB ASSEMBLY 1
6 ZEN289814131 CARBURETOR GASKET 1
7 ZEN0125230550 CARB BOLT 2
8 ZEN289814210 CYLINDER GASKET 2
ExPlODED vIEw
EN
21
No. Item Number Description Qty
9 ZEN0215230520 BOLT 8
10 ZEN289821001 CRANKCASE ASS’Y 1
11 ZEN202921130 PIN 4
12 ZENT401221240 BEARING 2
13 ZEN0406503515 SNAP RING 2
14 ZEN0603406202 BEARING 1
15 ZEN140021220 FRONT OIL SEAL 1
16 ZEN267021250 FUEL NIPPLE ELBOW 1
5 ZEN106581100 PIPE 1
18 ZEN289821310 CRANKCASE GASKET 1
19 ZEN0215230520 BOLT 4
20 ZENT200241110 PISTON 2
21 ZEN8488C41200 PISTON RING 2
22 ZEN285041310 PISTON PIN 2
23 ZEN130041320 PISTON PIN RETAINER 4
24 ZEN44524 BEARING 2
25 ZEN44525 THRUST WASHER 4
26 ZENEP8026 ZP80 CRANKSHAFT COMP. 1
27 ZEN130042410 SHIM 0-2
28 ZEN100043240 KEY 1
29 ZENP628011 PROP DRIvER LOCKING NUT ZP62/80 (M10x1) 1
36 ZEN369990032A G62/38/45/80T SPARK PLUG 2
43 ZEN289874110 MOUNT 1
44 ZEN0125230614 MOUNT BOLT 4
48 ZENPEI6 ZP80 ELECTRONIC IGNTION 1
49 ZENPH01 M4x8 SCREW (2) 2
52 ZENP628001 PROP DRIvER ZP62/80 1
55 ZENP628003 PROP WASHER (2) ZP62/80 2
56 ZENP8012 M5x35 PROP SCREWS (4) ZP80 4
ZENP8005 MUFFLER ZP80 2
ZENP8013 MUFFLER BOLTS (M5x12 (4)) ZP80 2
ZENPH15 M5 SqUARE NUT 2
ZENT210015210 MUFFLER GASKET 2
ZENP628027 IGNITION SENSOR WITH MOUNT ZP62/80 1
IT
84
©2012 Horizon Hobby, Inc.The ZP logo is a trademark of Horizon Hobby, Inc.The Zenoah logo is a registered trademark of Husqvarna Zenoah Co. Ltd. Corporation and is used with permission.Created 3/12 37334
top related