sjxx12xx series rohs · 2017. 10. 25. · revised: 07/31/17 specifications are subject to change...
Post on 04-Oct-2020
0 Views
Preview:
TRANSCRIPT
Revised: 08/08/17
Specifications are subject to change without notice. ©2017 Littelfuse, Inc
Thyristors12 Amp High Temperature Standard SCR
SJxx12xx Series
SJxx12xx Series
Description
This SJxx12xx high temperature SCR series is ideal for uni-directional switch applications such as phase control in heating, motor speed controls, converters/rectifiers and capacitive discharge ignitions.
These SCRs have a low gate current trigger level of 6mA or 20mA maximum at approximately 1.5V.
Features & Benefits
• Voltage capability up to 600V
• Surge capability up to 120A at 60 Hz half cycle
• 150°C maximum junction temperature
• Halogen free and RoHS compliant
Main Features
Symbol Value Unit
IT(RMS) 12 A
VDRM/VRRM 400 or 600 V
IGT 6 to 20 mA
Schematic Symbol
Applications
Typical applications includes capacitive discharge system for motorcycle engine CDI, portable generator engine ignition, strobe lights and nailers, as well as generic rectifiers, battery voltage regulators and converters. Also controls for power tools, home/brown goods and white goods appliances.
A K
G
RoHS
Absolute Maximum Ratings
Symbol Parameter Test Conditions Value Unit
IT(RMS) RMS on-state currentTC = 125°C
12 A
IT(AV) Average on-state current 7.6 A
ITSM
Peak non-repetitive surge current(single half cycle, TJ (initial) = 25°C)
f = 50Hz 100A
f = 60Hz 120
I2t I2t Value for fusing tp = 8.3 ms 60 A2s
di/dt Critical rate of rise of on-state current f = 60Hz; TJ = 150°C 100 A/μs
IGM Peak gate current Pw=20 μs, TJ = 150°C 2 A
PG(AV) Average gate power dissipation TJ = 150°C 0.5 W
TstgStorage temperature range -40 to 150
°CTJ Operating junction temperature range -40 to 150
VDSM/VRSM Peak non-repetitive blocking voltage Pw=100 μs VDRM/VRRM+100 V
Revised: 07/31/17
Specifications are subject to change without notice. ©2017 Littelfuse, Inc
Thyristors12 Amp High Temperature Standard SCR
SJxx12xx Series
Static Characteristics
Symbol Test Conditions Value Unit
VTM IT = 24A; tp = 380 µs MAX. 1.6 V
IDRM / IRRM @ VDRM = VRRM
TJ = 25°C
MAX.
10
μATJ = 125°C 500
TJ = 150°C 2000
Thermal Resistances
Symbol Parameter Value Unit
Rθ(J-C)Junction to case (AC) 1.4 °C/W
Figure 1: Normalized DC Gate Trigger Current vs. Junction Temperature
Figure 2: Normalized DC Gate Trigger Voltage vs. Junction Temperature
Ra�o
of I
GT
/IGT
(TJ=
25°C
)
Junc�on temperature (TJ)-(°C)
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
-40 -15 10 35 60 85 110 135 1500
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
-40 -15 10 35 60 85 110 135
Ratio
of V
GT
/ VGT
(TJ
= 25
Junction Temperature (TJ) --150
(°C)
°C)
Electrical Characteristics (TJ = 25°C, unless otherwise specified)
Symbol Test ConditionsValue
UnitSJxx12x1 SJxx12x
IGTVD = 12V RL = 60 Ω
MAX. 6 20mA
MIN. 2 5
VGT MAX. 1.5 1.5 V
dv/dt
VD = VDRM; gate open; TJ = 125°C400V
MIN.
100 250
V/μs600V 75 225
VD = VDRM; gate open; TJ = 150°C400V 50 200
600V 10 175
VGD
VD = VDRM RL = 3.3 kΩ TJ = 125°C MIN. 0.2 0.2V
VD = VDRM RL = 3.3 kΩ TJ = 150°C MIN. 0.1 0.1
IH IT = 200mA (initial) MAX. 20 40 mA
tq IT = 2A; tp = 50µs; dv/dt = 5V/µs; di/dt = 30A/µs MAX. 35 35 μs
tgt IG = 2 x IGT PW = 15µs IT = 12A TYP. 0.5 2 μs
Revised: 07/31/17
Specifications are subject to change without notice. ©2017 Littelfuse, Inc
Thyristors12 Amp High Temperature Standard SCR
SJxx12xx Series
Figure 5: Power Dissipation (Typical) vs. RMS On-State Current
0
0.2
0.4
0.6
0.8
1
1.2
1.4
-40 -15 10 35 60 85 110 135
Ratio
of I
H/ I
H(T
J=
25
Junction Temperature (TJ) -- (150
°C)
°C)
Figure 3: Normalized DC Holding Current vs. Junction Temperature
Figure 4: On-State Current vs. On-State Voltage (Typical)
0
5
10
15
20
25
30
35
0.7 0.8 0.9 1 1.1 1.2 1.3 1.4 1.5 1.6 1.7
Inta
ntan
eous
On-
stat
e Cu
rren
t (I T
) –Am
ps
Instantaneous On-state Voltage (VT) – Volts
0
2
4
6
8
10
12
14
0 2 4 6 8 10 12
Aver
age
On-
Stat
e Po
wer
Diss
ipat
ion
[PD
(AV)
] -(W
atts
)
RMS On-State Current [I T(RMS)] - (Amps)
Figure 6: Maximum Allowable Case Temperature vs. RMS On-State Current
Figure 7: Maximum Allowable Case Temperature vs. Average On-State Current
60
70
80
90
100
110
120
130
140
150
160
0 1 2 3 4 5 6 7 8
Max
imum
Allo
wab
leCa
se T
empe
ratu
re (T
C)-
RMS On-State Current [I T(RMS) ] - (Amps)
°C
60
70
80
90
100
110
120
130
140
150
160
0 2 4 6 8 10 12 14
Max
imum
Allo
wab
leCa
se T
empe
ratu
re (T
C)-
RMS On-State Current [I T(RMS)] - (Amps)
°C
Figure 8: Peak Capacitor Discharge Current
10
100
1000
0.050.520.55.0
Peak
Dis
char
ge C
urr
ent
(IT
M)
- Am
ps
Pulse Current Duration (tw) - ms
ITRM
tW
Revised: 07/31/17
Specifications are subject to change without notice. ©2017 Littelfuse, Inc
Thyristors12 Amp High Temperature Standard SCR
SJxx12xx Series
Figure 11: Peak Capacitor Discharge Current Derating
0.0
0.2
0.4
0.6
0.8
1.0
1.2
0 25 50 75 100 125 150
No
rmal
ized
Pea
k C
urr
ent
Case Temperature (TC) - °C
1
10
100
1000
0001001011
Peak
Su
rge
(No
n-r
epet
itiv
e)O
n-s
tate
Cu
rren
t (I
TS
M )
– A
mp
s
Surge Current Duration - Full Cycles
Figure 12: Surge Peak On-State Current vs. Number of Cycles
SUPPLY FREQUENCY: 60 Hz Sinusoidal LOAD: ResistiveRMS On-State Current: [IT(RMS)]: Maximum Rated Value at Specified Case Temperature
Notes:1. Gate control may be lost during and immediately
following surge current interval.2. Overload may not be repeated until junction
temperature has returned to steady-state rated value.
Soldering Parameters
Reflow Condition Pb – Free assembly
Pre Heat
- Temperature Min (Ts(min)) 150°C
- Temperature Max (Ts(max)) 200°C
- Time (min to max) (ts) 60 – 180 secs
Average ramp up rate (Liquidus Temp) (TL) to peak
5°C/second max
TS(max) to TL - Ramp-up Rate 5°C/second max
Reflow- Temperature (TL) (Liquidus) 217°C
- Temperature (tL) 60 – 150 seconds
Peak Temperature (TP) 260+0/-5 °C
Time within 5°C of actual peak Temperature (tp)
20 – 40 seconds
Ramp-down Rate 5°C/second max
Time 25°C to peak Temperature (TP) 8 minutes Max.
Do not exceed 280°C
Time
Tem
pera
ture
TP
TLTS(max)
TS(min)
25
tP
tL
tS
time to peak temperature
PreheatPreheat
Ramp-upRamp-up
Ramp-downRamp-do
Revised: 07/31/17
Specifications are subject to change without notice. ©2017 Littelfuse, Inc
Thyristors12 Amp High Temperature Standard SCR
SJxx12xx Series
Physical Specifications Environmental Specifications
Test Specifications and Conditions
AC BlockingMIL-STD-750, M-1040, Cond A Applied Peak AC voltage @ 150°C for 1008 hours
Temperature CyclingMIL-STD-750, M-1051,100 cycles; -40°C to +150°C; 15-min dwell-time
Temperature/Humidity
EIA / JEDEC, JESD22-A1011008 hours; 160V - DC: 85°C; 85% rel humidity
High Temp StorageMIL-STD-750, M-1031,1008 hours; 150°C
Low-Temp Storage 1008 hours; -40°C
Resistance to Solder Heat
MIL-STD-750 Method 2031
Solderability ANSI/J-STD-002, category 3, Test A
Lead Bend MIL-STD-750, M-2036 Cond E
Moisture Sensitivity Level
Level 1, JEDEC-J-STD-020
Terminal Finish 100% Matte Tin-plated
Body MaterialUL Recognized epoxy meeting flammability rating V-0
Lead Material Copper Alloy
Design Considerations
Careful selection of the correct component for the application’s operating parameters and environment will go a long way toward extending the operating life of the Thyristor. Good design practice should limit the maximum continuous current through the main terminals to 75% of the component rating. Other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. Overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. Correct mounting, soldering, and forming of the leads also help protect against component damage.
Dimensions — TO-251AA (V/I-Package) — V/I-PAK Through Hole
DimensionInches Millimeters
Min Typ Max Min Typ Max
A 0.040 0.044 0.050 1.02 1.11 1.27
B 0.235 0.242 0.245 5.97 6.15 6.22
C 0.350 0.361 0.375 8.89 9.18 9.53
D 0.205 0.208 0.213 5.21 5.29 5.41
E 0.255 0.262 0.265 6.48 6.66 6.73
F 0.027 0.031 0.033 0.69 0.80 0.84
G 0.087 0.090 0.093 2.21 2.28 2.36
H 0.085 0.092 0.095 2.16 2.34 2.41
I 0.176 0.180 0.184 4.47 4.57 4.67
J 0.018 0.020 0.023 0.46 0.51 0.58
K 0.038 0.040 0.044 0.97 1.01 1.12
L 0.018 0.020 0.023 0.46 0.52 0.58
P 0.042 0.047 0.052 1.06 1.20 1.32
Q 0.034 0.039 0.044 0.86 1.00 1.11
R 0.034 0.039 0.044 0.86 1.00 1.11
S 0.074 0.079 0.084 1.86 2.00 2.11
AREA: 0.040 IN2TC MEASURING POINT
GATEG
I
E
D
A
B
C
F
J
H
K
L
5.28.208
5.34.210
Anode
Cathode
Anode
PQ
RS
Revised: 07/31/17
Specifications are subject to change without notice. ©2017 Littelfuse, Inc
Thyristors12 Amp High Temperature Standard SCR
SJxx12xx Series
Dimensions — TO-252AA (D-Package) — D-PAK Surface Mount
DimensionInches Millimeters
Min Typ Max Min Typ Max
A 0.040 0.043 0.050 1.02 1.09 1.27
B 0.235 0.243 0.245 5.97 6.16 6.22
C 0.106 0.108 0.113 2.69 2.74 2.87
D 0.205 0.208 0.213 5.21 5.29 5.41
E 0.255 0.262 0.265 6.48 6.65 6.73
F 0.027 0.031 0.033 0.69 0.80 0.84
G 0.087 0.090 0.093 2.21 2.28 2.36
H 0.085 0.092 0.095 2.16 2.33 2.41
I 0.176 0.179 0.184 4.47 4.55 4.67
J 0.018 0.020 0.023 0.46 0.51 0.58
K 0.038 0.040 0.044 0.97 1.02 1.12
L 0.018 0.020 0.023 0.46 0.51 0.58
M 0.000 0.000 0.004 0.00 0.00 0.10
N 0.021 0.026 0.027 0.53 0.67 0.69
O 0° 0° 5° 0° 0° 5°
P 0.042 0.047 0.052 1.06 1.20 1.32
Q 0.034 0.039 0.044 0.86 1.00 1.11
M
O
N
HJ
L
K
.1183
.0631.60
.0711.80
.2646.71
.2646.71
.1814.60
GATE
Anode
Cathode
Anode
TC MEASURING POINT
G
I
DE
A
B
C
F
5.28.208
5.34.210
: 0.040 IN2AREA
PQ
Product Selector
Part NumberVoltage
Gate Sensitivity Type Package400V 600V
SJxx12V X X 20mA Standard SCR TO-251
SJxx12D X X 20mA Standard SCR TO-252
SJxx12V1 X X 6mA Standard SCR TO-251
SJxx12D1 X X 6mA Standard SCR TO-252
Note: xx = voltage
Packing Options
Part Number Marking Weight Packing Mode Base Quantity
SJxx12DTP SJxx12D 0.3 g Tube 750 (75 per tube)
SJxx12DRP SJxx12D 0.3 g Embossed Carrier 2500
SJxx12VTP SJxx12V 0.4 g Tube 750 (75 per tube)
SJxx12D1TP SJxx12D1 0.3 g Tube 750 (75 per tube)
SJxx12D1RP SJxx12D1 0.3 g Embossed Carrier 2500
SJxx12V1TP SJxx12V1 0.4 g Tube 750 (75 per tube)
Note: xx = Voltage
Revised: 08/08/17
Specifications are subject to change without notice. ©2017 Littelfuse, Inc
Thyristors12 Amp High Temperature Standard SCR
SJxx12xx Series
0.512 (13.0) ArborHole Dia.
XX
XX
XX
XX
XX
XX
XX
XX
XX
DC
XX
XX
XX
Gate Cathode
Anode
0.63(16.0)
0.157(4.0)
0.64(16.3)
12.99(330.0)
0.524(13.3)
0.315(8.0)
0.059 Dia(1.5)
*
* Cover tape
Direction of Feed
Dimensionsare in inches(and millimeters).
DC
DC
TO-252 Embossed Carrier Reel Pack (RP) Specifications
Meets all EIA-481-2 Standards
Part Numbering System Part Marking System
SJ 60 12 D RP
COMPONENT TYPESJ: High TJ SCR
VOLTAGE RATING40: 400V60: 600V
CURRENT RATING12: 12A
PACKAGE TYPE
V: TO-251 (V/I-Pak)
PACKAGING OPTIONSRP: Reel PackTP: Tube Pack
D: TO-252 (D-Pak)
1
Sensitivity & Type1: 6mA(blank): 20mA YMLDD
®
Date Code Marking Y:Year Code M: Month Code L: Location Code DD: Calendar Code
SJ6012V
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications. Read complete Disclaimer Notice at www.littelfuse.com/disclaimier-electronics.
top related