sealing kit spool page 1/2 fits: consumption: 1 kit …shell gadus s3 a1300c 2 (srs 4000) rust...
Post on 24-Feb-2020
0 Views
Preview:
TRANSCRIPT
Sealing kit spool
Sealing kit spool
170503141 Edition 2 - 2018-03-21
Fits: All manual operated Pv90, Q200 and Q300 valvesConsumption: 1 kit per valve section
Contains
1 x Tube grease 20g
A
1. Dismount the cover on the spring side of the spool using a 5mm hexagon wrench.2. Press the lever to push the spool into it’s end position and mount the spring holder (can be bought
separately) over the centering spring.3. Use the a mm socket wrench to loosen the spring bolt .4. Remove the lever link and dismount the console , then carefully pull the spool out from the valve body.5. Unscrew the spring bolt and separate the spring package from the spool.6. Dispose the old glyd rings and o-rings (on both sides of the valve).7. Mount the small supplied o-ring inside the new glyd ring.8. Mount the new seal on the spring side of the spool.9. Remount the spring package and tighten the spring bolt by hand.
A
SHELL GADUS S3 A1300C 2 (SRS 4000)Rust protection grease
Page 1/2
B
B
C
C
D
D
4
1
2
3
F
E
Inspect the spool and make sure that the surface is not affected by dirt or corrosion.
Do NOT attempt to mount the glyd ring from the lever side of the spool. The glyd ring will be severely damaged when it passes all the sharp edges on the spool.
5
DG
8
9
I
E F
D G
I
G
G
D
D
2 x O-ring Ø 22,1 2 x O-ring Ø 26,57
SHELL GADUS S3 A1300C 2 (SRS 4000)Rust protection grease
2 x Glyd ring Ø 22 M12
SHELL GADUS S3 A1300C 2 (SRS 4000)Rust protection grease
SHELL GADUS S3 A1300C 2 (SRS 4000)Rust protection grease
7
HI
H
Sealing kit spool 170503141 Edition 2 - 2018-03-21
Fits: All manual operated Pv90, Q200 and Q300 valvesConsumption: 1 kit per valve section
Page 2/2
10. Place the supplied grease on the spring package and around the spool on both sides of the seal.11. Place the supplied supplied large o-ring in the cavity on both sides of the valve.12. Gently push the spool back into the valve.13. Repeat step 7 and the push the new glyd ring onto the spool end.14. Place the supplied grease around the spool on both sides of the seal and on the console.15. Remount the console and the lever link .16. Tighten the spring bolt with torque 6 ±1 Nm, before taking away the spring holder .17. Remount the spring cover .
6 ±1Nm
10
LL
L
11 12
13
14
I
I
L
L
F E
EF
L
17
15
16
D C
A
C
D
A
Sealing kit spool
Contains
1 x Tube grease 20g
SHELL GADUS S3 A1300C 2 (SRS 4000)Rust protection grease
12 x O-ring Ø 22,1 12 x O-ring Ø 26,57
SHELL GADUS S3 A1300C 2 (SRS 4000)Rust protection grease
12 x Glyd ring Ø 22 M12
SHELL GADUS S3 A1300C 2 (SRS 4000)Rust protection grease
SHELL GADUS S3 A1300C 2 (SRS 4000)Rust protection grease
top related