s121 - 1.5' define dr rdr - direct recessed - … … · description catalog project comments...
Post on 17-Aug-2018
269 Views
Preview:
TRANSCRIPT
DESCRIPTION
Catalog #
Project
Comments
Prepared by
Type
Date
SPECIFICATION FEATURES
Eaton18001 E. Colfax AvenueDenver, CO 80011P: 303-393-1522 www.eaton.com/lighting
Specifications and dimensions subject to change without notice.See additional information on the following pages.
TD519030EN06/08/2018
1 of 5
Light Distribution Light Engine Lumen Package Down CCT & Min CRI Celing Type Length Circuiting
S121DRS = Define 1Direct Recessed with Remote DriverS121RDRS = Define 1 1” Regressed Direct Re-cessed with Remote Driver
-S = Standard-H = High Performance
305D = 305 Lms/ft490D = 490 Lms/ft685D = 685 Lms/ft880D = 880 Lms/ft1025D = 1025 Lms/ft____D = Custom Lm/Ft
830 = 3000K, 80CRI835 = 3500K, 80CRI840 = 4000K, 80CRI927 = 2700K, 90CRI 930 = 3000K, 90CRI935 = 3500K, 90CRI940 = 4000K, 90CRI
-ETG = 15/16” T-Grid-FTG = 9/16” T-Grid-STG = 9/16” Slot T-Grid-FTT = 9/16” Tegular T-Grid-ITG = 9/16” Interlude T-Grid-ETT = 15/16” Tegular T-Grid-GYP = Gypsum board-FSR = “Flangeless” Gypsum Board-FES = “Finished” Extruded Side
2F0 = 2’ Individual4F0 = 4’ Individual8F0 = 8’ Individual12F0 = 12’ Individual__F0 = 4’ Incremental Run (e.g. 40F0 = 40’ 0”)__F_ = 1” Incremental Run (e.g. 21F3 = 21’ 3”)
-1 = Single Circuit-S = Secondary Circuit
Please refer to performance table to determine based on efficacy requirements.
3500K/80CRI/DR housing/F Lens. Please refer to scaling data for other variables. For custom lumen output, please refer to additional information on page 2.
Additional lead-time and cost may apply for 927, 930, 935 and 940 configurations.
Please refer to ceiling interface diagrams for ad-ditional detail and dimensions.
Secondary circuit similar to A/B switching. Price adder applies for “S” configuration.
Neo-Ray
ORDERING INFORMATION
Sample Number: S121DRS-S490D840-ETG4F0-1B1-UDD-F-W-SWPD1
Emergency Voltage Remote LED Driver Shielding Down Options Color Integrated Sensor
E = Emergency circuitB1 = Surelite 7W UNV integral batteryB2 = Surelite 14W UNV integral batteryT = Iota UL924 ETR Emergency Bypass Relay
-U = UNV 120-277V-1 = 120V-2 = 277V-3 = 347V-4 = 48VDC
DD= 0-10 Volt Dimming, 1%5L = DALI Dimming, 5%-100%L5 = Lutron 5-Series LDE5 w/ecosysLH = Lutron HiLume LDE1 w/ecosysLU = Lutron HiLume L3D w/3WLV1 = DLVP
-F = Satin Flush Diffuser-A = Asym Flush Optic-D = Satin Drop Diffuser
-CP = Chicago Plenum-R = GLR Fuse (Fast)-F = GLF Fuse (Slow)
-W = Matte White-S = Silver-B = Black-C = Custom Color
-SWTPD1 = WaveLinx Tilemount-LWTPD1 = LumaWatt Pro Tilemount-SVTPD1 = Standalone Sensor Tilemount
Internal battery standard in remote driver enclosure. External battery standard with chicago plenum.
48V for use with LV1 driver. 347V only availabe with DD and 5L drivers.
DD driver is standard. All lensing options are snap-in lenses.
Contact factory for custom color
Please refer to page 5 for additional detail required to specify integrated or tile-mount sensors. Not available with Chicago Plenum - contact factory if required.
quick disconnect wire-harness for ease of installation and maintence over the life of the luminaire.
Light Engine Offered with two next generation Neo-Ray light engines delivering industry leading efficacy and long-life.
LED’s are available in 2700K, 3000K, 3500K or 4000K. CRI options of either ≥80CRI or ≥90CRI are available. Lumen output will be effected - please refer to the lumen adjustment factor table.
LED DriversLED system coupled with remotely mounted electrical driver to deliver
optimal performance. Traditional electronic drivers are available for 120-277V and 347V applications. Eaton’s DLVP Low voltage drivers are available for 48VDC applications.
Controls and Integrated SensorsEquipped standard with a 0-10V continuous dimming driver compatible with most standard dimming devices. Additional control types are available (DALI, Lutron, DLVP) at an additional cost. WaveLinx and LumaWatt Pro wireless sensors as well as stand-alone sensors available.
WarrantyFive year warranty.
ConstructionPrecision cut housing trim extruded from 6063 aluminum with aluminum frame. Extruded end-caps ensure a precise and uniform ceiling interface.Nominal 2’ -12’ illuminated sections used in run configuration and/or individual fixtures.
FinishFixture housing trims are high reflective white (unless otherwise specified) using electrostatically applied polyester powder coat paint.
LED ModuleModular LED tray assembly comprising reflector, light engine, led driver and
Remote LED Driver Enclosure
DEFINE 1 LED
Recessed Direct
The Define series by Neo-Ray characterizes the ultimate in minimalist simplicity by providing clean, uniform lines of illumination in virtually any architectural environment. Powered Eaton’s most advanced linear LED technology, the Define series delivers out-standing efficacy in a variety of profile widths. 1.5”, 2”, 3”, 4” and 5” luminaire widths are all specifiable to the nearest inch in length and can be fitted with standard flush, asym-metric flush, regressed and drop lensing. In-ceiling and in-wall corners as well as wall to ceiling transitions can all be ordered as standard components and blend seamlessly into the most complex architectural spaces. Custom transitions are also available. Robust construction and adaptable, modular components make installation simple and ensure laser straight runs.
cULus – 1598Damp Location Listed
LM79/LM80 CompliantROHS Compliant
Lumawatt Pro WirelessWaveLinx Wireless
Made in USA
S121DR2.500" (64mm)
2.750"
1.500" (38mm)1.180" (30mm)
S121RDR2.500" (64mm)
2.750"
1.500" (38mm)1.180" (30mm)
1.000"
Eaton18001 E. Colfax AvenueDenver, CO 80011P: 303-393-1522 www.eaton.com/lighting
Specifications and dimensions subject to change without notice.See additional information on the following pages.
TD519030EN06/08/2018
2 of 5
Neo-Ray - Define - RecessedNeo-Ray - Define - RecessedSPECIFICATION FEATURES CONTINUED
high reflectivity (standard) and ultra-high reflectivity (used with High Performance light engine).
Lumen Maintenance90% (L90) of initial light output at 100,000+ hrs. 70% (L70) of initial light output at 400,000+ hrs, reported L70 >60,000 hrs. Derived from TM-21 calculator @25°C ambient and typical operating conditions. Consult factory for additional data.
Custom Lumen OutputYou can select a custom lumen output for your application in Lumens per foot (e.g. -725D for 725 Lms/ft down). Desired output must with within the total light output range. Please contact factory for custom lumen output when not selecting the standard 0-10V ‘DD’ Driver.
If your requirement is expressed in power consumption (W/ft) rather than light output, you can use the power to lumen output curves to convert power consumption to light output for specification.
Efficacy for custom lumen outputs can be estimated using lumen output curves or with the use of our online custom lumen output tool.
ElectricalDimming provided as standard - dimming wires are capped with wire-nuts for non-dimming applications.
Optional battery backup options provided. Default battery location is internal to fixture to reduce field wiring with pre-wired external test switch. Default emergency section is 4ft in length and located at the beginning of the fixture unless designated elsewhere using our linear product configurator tool. To estimate lumen output from the emergency section, multiply battery wattage x minimum fixture efficacy from performance table below (e.g. 14W x 99 lm/W = 1386 lms).
Our ETS-DR option will provide switching for both power and wires for applications requiring a UL924 transfer device.
Integrated SensorsPlease reference page 5 for details.
Weight1.5 lbs per foot of fixture + 2.0 lbs per driver enclosure (excluding battery)
ApprovalscULus - 1598Meets NYC requirements.Meets CCEC requirements (Chicago Plenum).Suitable for damp locations.IC Rated (except where noted)
MountingRecessed.
LengthsAvailable in any length (23” min) with a resolution of 1 inch. Max section length of 12ft (8ft max option available). Additional fixture lengths are available - please consult factory.
All lengths are nominal. Actual sizes are one inch shorter than nominal to allow easy in-grid installation. For Gypsum or Flangeless installations add 1 inch to overall fixture length. Refer to ceiling type section of specification sheetand submittal drawings for actual sizes.
Corners and Transition PiecesCorners and other transition pieces are fully luminous and contructed using precision mitered frame and lens components. The frame is welded to ensure a precise and robust assembly. Standard 90° horizontal and vertical corners as well as custom corners are available. Please consult online linear configutor or the factory for precise corner locations and for ordering. Alternative transition pieces such as T’s, Y’s, X’s, etc. are also available.
Snap-In Lensing OptionsSatin Flush - Flush, high diffusion glare-free lensSatin Proud - 1” Proud, high diffusion glare-free lensAsymmetric - Flush, low-glare Asymmetric lens
Flush options ship with our patent-pending under-lens solution, while the proud lens ships with an injection molded end cap to eliminate light leak.
ReflectorsPrecision formed cold-rolled steel reflectors with
PERFORMANCE PER LINEAR FOOT AT 3500K/80CRI
Nominal Lumen Output
StandardLight Engine
High Performance Light Engine
305 lms/ft 2.9 W/ft 104 lm/W 2.8 W/ft 107 lm/W
490 lms/ft 4.7 W/ft 105 lm/W 4.3 W/ft 111 lm/W
685 lms/ft 6.6 W/ft 105 lm/W 5.9 W/ft 114 lm/W
880 lms/ft 8.7 W/ft 101 lm/W 7.9 W/ft 110 lm/W
1025 lms/ft 10.3 W/ft 99 lm/W 9.4 W/ft 107 lm/W
LUMEN ADJUSTMENT FACTORS
PHOTOMETRIC OVERVIEW AND PERFORMANCE DATA
Example 1 - Adjusted Lumen Output Nominal Lumen Output selected = 1025 lms/ft (based on standard of 3500K/80CRI)Lumen Adjustment Factor = 0.801 (2700K/90CRI desired)
Adjusted Lumen Output = Nominal Lumen Output x Lumen Adjustment FactorAdjusted Lumen Output = 1025 lms/ft x 0.801 = 821 lms/ft
Example 2 - Custom Lumen Output based on Required Lumens Per FootTotal light output (4ft) requirement of 2800 lms, desired CCT and CRI of 4000K/80CRI
Total required lumens per foot @ 4000K= 2800 lms / 4 ft = 700 lms/ftLumen Adjustment Factor = 1.018 (Requirement based on 4000K / 80CRI)
Total required lumens per foot @ 3500K / 80CRI = 700 lms/ft ÷ 1.018 = 688 lms/ft
Estimated efficacy = 121 lm/W (find nearest value using table above)Estimated power consumption = 688 lms/ft ÷ 121 lm/W = 5.69 W/ft
S121DR with Flush Satin Lens (F)
S121DR with Drop Satin Lens (D)
S121RDR with Regressed Satin Lens (F)
S121DR with Flush Asymmetric Lens (A)
LUMEN ADJUSTMENT CALCULATIONS
TOTAL LIGHT OUTPUT RANGE (lms/ft)
CCT 80CRI 90CRI
2700K N/A 162-909
3000K 191-1070 165-925
3500K 202-1134 174-977
4000K 204-1146 180-1012
SHEILDING OPTIONS
CCT 80CRI 90CRI
2700K N/A 0.801
3000K 0.943 0.815
3500K 1.000 0.861
4000K 1.010 0.892
Eaton18001 E. Colfax AvenueDenver, CO 80011P: 303-393-1522 www.eaton.com/lighting
Specifications and dimensions subject to change without notice.See additional information on the following pages.
TD519030EN06/08/2018
3 of 5
Neo-Ray - Define - RecessedPHOTOMETRICS
FILE NAME: S121DRS-S685D835-GYP4F0-1-UDD-F-W CCT: 3500K
LUMENS: 2750.3 Lms WATTS: 26.2 W
LPW: 105 LPW TEST G3-1802-639-9
FILE NAME: S121DRS-S685D835-GYP4F0-1-UDD-A-W
CCT: 3500K
LUMENS: 2864 Lms
WATTS: 26.3 W
LPW: 108.9 LPW
TEST NUMBER: G3-1802-639-18
0°
30°
60°
90°
15°
45°
75°273
545
818
1090 0 deg90 deg
SATIN FLUSH LENS
SATIN DROP LENS
ASYMMETRIC LENS
REGRESSED SATIN DIFFUSER
LUMINANCE DATA (CD/M2)
Vertical Angle 0º 45º 90º
45 27320 26201 25537
55 25401 24123 23254
65 23306 21780 20670
75 20161 18462 17216
85 14799 12108 10763
ZONAL LUMENS SUMMARY
Zone Lumens % Fixture
0º-30º 812 29.5
0º-40º 1302 47.3
0º-60º 2217 80.6
0º-90º 2750 100.0
LUMINANCE DATA (CD/M2)
Vertical Angle 0º 45º 90º
45 16197 12208 11764
55 14880 11132 10832
65 13599 10054 9833
75 11647 8890 8762
85 8928 7768 7746
ZONAL LUMENS SUMMARY
Zone Lumens % Fixture
0º-30º 526 19.2
0º-40º 865 31.7
0º-60º 1598 58.5
0º-90º 2377 87.0
90º-120º 297.6 10.9
90º-150º 355.3 13.0
90º-180º 355.0 13.0
ZONAL LUMENS SUMMARY
Zone Lumens % Fixture
0º-30º 831 37.2
0º-40º 1263 56.5
0º-60º 1925 86.1
0º-90º 2236 100.0
LUMINANCE DATA (CD/M2)
Vertical Angle 0º 45º 90º
45 27610 16678 11977
55 25988 12051 8831
65 23910 8802 7554
75 20693 7237 6422
85 14833 5449 4843
ZONAL LUMENS SUMMARY
Zone Lumens % Fixture
0º-30º 937 32.7
0º-40º 1506 52.6
0º-60º 2418 84.4
0º-90º 2864 100.0
CANDELA DISTRIBUTION (CD)
Vertical Angle 0º 90° 270°
0 1162 1162 1162
10 1148 1430 962
20 1074 1635 706
25 1021 1677 634
30 956 1511 578
40 779 828 490
50 548 444 397
60 346 274 296
70 192 164 183
80 69 54 68
90 0 0 0
FILE NAME: S121DRS-S685D835-GYP4F0-1-UDD-D-W CCT: 3500K
LUMENS: 2732.5 Lms WATTS: 26.3 W
LPW: 103.9 LPW TEST G3-1802-639-13
FILE NAME: S121RDRS-S685D835-GYP4F0-1-UDD-F-W CCT: 3500K
LUMENS: 2236.4 Lms WATTS: 26.4 W
LPW: 84.7 LPW TEST G3-1802-639-23
0°
30°
60°
90°
15°
45°
75°169
339
508
677 0 deg90 deg
0°
30°
60°
90°
15°
45°
75°300
601
901
1201 0 deg90 deg
0°
30°
60°
90°
15°
45°
75°
0 deg90 deg
1677
1258
839
419
1”[25.4MM]
1”[25.4MM]
Eaton18001 E. Colfax AvenueDenver, CO 80011P: 303-393-1522 www.eaton.com/lighting
Specifications and dimensions subject to change without notice.See additional information on the following pages.
TD519030EN06/08/2018
4 of 5
Neo-Ray - Define - RecessedCEILING TYPE
15/16 Tegular (ETT)
Mud-In Flange (FSR)
9/16 Tee (FTG)15/16 Tee (ETG)
Finished Extruded Side (FES)
9/16 Tegular (FTT)
Visible Flange (GYP)
9/16 Interlude Tee (ITG)
9/16 Slotted Tee (STG)
Grid Ceiling Systems
Drywall Ceiling
Other Ceiling Systems (Wood, Fabric, Metal Pan, HD Box Style)Typical Installations using Finished Extruded Side (FES)
DRIVER LOCATED IN AREMOTE ENCLOSURE
WIRED TO FIXTUREBY FACTORY
2.500"GRID CENTERS
CROSS SECTION
OVERALLRUN LENGTH
GRID CENTERS
SIDE VIEW
0.375"END
FLANGE
2.750"
DRIVER LOCATED IN AREMOTE ENCLOSURE
WIRED TO FIXTUREBY FACTORY
2.500"GRID CENTERS
CROSS SECTION
OVERALLRUN LENGTH
GRID CENTERS
SIDE VIEW
0.375"END
FLANGE
2.750"
DRIVER LOCATED IN AREMOTE ENCLOSURE
WIRED TO FIXTUREBY FACTORY
2.500"GRID CENTERS
CROSS SECTION
OVERALLRUN LENGTH
GRID CENTERS
SIDE VIEW
0.375"END
FLANGE
2.750"
DRIVER LOCATED IN AREMOTE ENCLOSURE
WIRED TO FIXTUREBY FACTORY
2.500"GRID CENTERS
CROSS SECTION
OVERALLRUN LENGTH
GRID CENTERS
SIDE VIEW
0.375"END
FLANGE
2.750"
DRIVER LOCATED IN AREMOTE ENCLOSURE
WIRED TO FIXTUREBY FACTORY
2.500"GRID CENTERS
CROSS SECTION
OVERALLRUN LENGTH
GRID CENTERS
SIDE VIEW
0.375"END
FLANGE
2.750"
DRIVER LOCATED IN AREMOTE ENCLOSURE
WIRED TO FIXTUREBY FACTORY
2.500"GRID CENTERS
CROSS SECTION
OVERALLRUN LENGTH
GRID CENTERS
SIDE VIEW
0.375"END
FLANGE
2.750"
2.188"
DRIVER LOCATED IN AREMOTE ENCLOSURE
WIRED TO FIXTUREBY FACTORY
1.750"CUTOUT
CROSS SECTION
OVERALLRUN LENGTH
CEILING CUTOUT
SIDE VIEW
0.375"END
FLANGE
2.750"
2.188"
DRIVER LOCATED IN AREMOTE ENCLOSURE
WIRED TO FIXTUREBY FACTORY
1.750"CUTOUT
CROSS SECTION
OVERALLRUN LENGTH
CEILING CUTOUT
SIDE VIEW
1.000"MUD
FLANGE
2.750"
2.188"
DRIVER LOCATED IN AREMOTE ENCLOSURE
WIRED TO FIXTUREBY FACTORY
1.500"WIDTH
CROSS SECTION
OVERALLRUN LENGTH
SIDE VIEW
2.750"
1.000"Finished Side
WOOD SLAT
1.500"WIDTH
WOOD PANELING
1.500"WIDTH
FABRIC PANELS
1.500"WIDTH
METAL PAN
1.500"WIDTH
NOTE: ACTUAL LENGTH OF GYP/FSR FIXURES WILL BE 1” SHORTER IN LENGTHTHAN TOTAL REQUESTED RUN LENGTH FOR ALL RECESSED / PERIMETER FIXTURES
OVERALL RUN LENGTH = ‘FIXTURE ORDER LENGTH’ - 1” E.G. - OVERALL RUN LENGTH OF 3’ 11” WILL SHIP WHEN ORDERING A ‘4F0’ FIXTURE
CEILING CUTOUT = ‘OVERALL RUN LENGTH’ + 0.250”OR CEILING CUTOUT = ‘FIXTURE ORDER LENGTH’ - 0.750” E.G. - CEILING CUTOUT WHEN ORDERING A ‘4F0’ LENGTH FIXTURE WILL BE 3’ 11.250”
Extruded Trim Flange Details - Refer to submittal drawings for detailed flange information - for additional options consult factory.
Eaton18001 E. Colfax AvenueDenver, CO 80011P: 303-393-1522 www.eaton.com/lighting
Specifications and dimensions subject to change without notice.See additional information on the following pages.
TD519030EN06/08/2018
5 of 5
Neo-Ray - Define - RecessedCORNER TRANSITIONS
24.188”(614mm)
24.188”(614mm)
24.188”(614mm)
24.188”(614mm)
INTEGRATED SENSOR DETAILS AND PLACEMENT
Sensor Type Wireless Sensor Integration Sensor Mounting Ordering Code
WaveLinx Yes Pre-wired for tile-mount Installation in ceiling tile or J-Box cover SWTPD1
LumaWatt Pro (enlighted)
Yes Pre-wired for tile-mount Installation in ceiling tile or J-Box cover LWTPD1
Stand-Alone SVPD1
No Pre-wired for tile-mount Installation in ceiling tile or J-Box cover SVTPD1
Individual
TILEMOUNT SENSOR (OPTIMAL LOCATION)
Beginning of Run (BOR)
Intermediate Section (INT)
End of Run
Standard Sensor with Luminaire ControlAuxilary Sensor used for Sensor Coverge (wireless systems only)
Optional standalone and wireless connnected integrated sensors require use of the DD (0-10V) driver. WaveLinx and LumaWatt Pro sensors require additional system hardware (not provided) for full functionality. Integral sensor not available on Define 1 configurators due to size limitations.
Standard sensor layout is shown below. Please refer to sensor coverage pattern diagrams to ensure proper coverage for the application. Standard configurations are available in both individual fixtures and in continous runs. Default spacing is based on the maximum fixture length of 12ft and can be changed to 8ft sensor spacing for additional coverage by selecting the 8ft max fixture length option when ordering.
For additional information integrated sensors and connected lighting, please visit Eaton’s Connected Lighting
Website...
top related