rt software tog gv sports and k2 dyno s - grass valley · alicaion no rt software tog gv sports and...
Post on 29-May-2020
5 Views
Preview:
TRANSCRIPT
RT Software tOG GV Sports and K2 Dyno S Olaf Bahr Product Manager Grass Valley a Belden Brand
July 2015
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
2wwwgrassvalleycom
WHY tOG ON K2 DYNO S
The speed of live events and the need to efficiently tell the story of ldquowhat just happenedrdquo is increasingly in demand to be faster more dynamic paint a clearer picture and even be more entertaining to enhance the viewing experience The integration of tOG and K2 Dyno brings an affordable A-level analysis tool to every level of live event production
This Application Note covers
bull Software installation and setup on K2 Dyno S
bull Software installation and setup on the tOG PC
bull Preparing the K2 Summit 3G for interaction with tOG
bull Using the K2 Dyno StOG interface
bull Building stacked overlay graphics
Prior to using this Application Note verify with the K2 Dyno S K2 Summit 3G and tOG release notes that the appropriately compati-ble versions of software on all systems is being used Visit the Grass Valley K2 Dyno website for updated information regarding software releases required software and documentation wwwgrassvalleycomproductsk2_dyno and click on the Documentation tab in the Resources area
Required software for K2 Dyno installation in the RTDyno_Installzip file
ChromeStandaloneSetupexe
GoogleUpdateadm
tOGGVDynoClientcrx
tOGGVDynoClientpem
Required software for tOG Server installation
togpre-46_14565-windows-installer
tog-46_r15288-windows-installer
mysql-5535-winx64
dvsdriver-4354_1-windows-installer
gvsports-46_r15288-windows-installer
Have the IP address subnet mask and any other IP configuration information readily available for the K2 Dyno S K2 Summit 3G and tOG server In either a standalone or SAN configuration the K2 Dyno S K2 Summit 3G and tOG server need to be connected via a Gigabit Ethernet switch or router
For this Application Note example the IP addresses are
K2 Summit 3G 10164170
K2 Dyno S 10164171
tOG server PC 10164179
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
3wwwgrassvalleycom
Installation on K2 Dyno S
1) If the K2 Dyno application is running exit the application to the K2 Dyno S Mainte-nance level in order to see the Windows desktop
2) Verify that McAfee Embedded Security Manager is set to UPDATE
3) If not connected connect the K2 Dyno S Controller to the Internet via the Media Port on the back
4) Insert a USB device with the RTDyno_Install files
5) Run the ChromeStandaloneSetupexe
6) With an Internet connection Chrome will install on the K2 Dyno S controller Close the Chrome Browser application From this point Internet connection is no lon-ger required
7) To prevent Chrome from automatically downloading and installing updates that have not been tested in this environment it is advised the following adjustments to Chrome are made Use Windows Start menu and type in Edit group policy
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
4wwwgrassvalleycom
Installation on K2 Dyno S (cont)
8) From the selection click on Edit group policy When the window opens under User Configuration right-click on Administrative Templates then AddRemove Templates
9) Click Addhellip and browse to the RTDyno_Install folder that contains the file GoogleUpdateadm and select it and click Open
10) If it is listed in the window of tem-plates close the window
11) Under Computer Configuration select Administrative TemplatesClas-sic Administrative TemplatesGoogleGoogle UpdateApplications Google Chrome
12) In this folder right-click on Update policy override and select Edit
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
5wwwgrassvalleycom
Installation on K2 Dyno S (cont)
13) Change Update policy override to Enabled and Policy to Updates disabled
14) Then click Apply and then OK close all windows
15) Open a Chrome browser window and type in the URL search field chromeextensions This will open the Chrome extensions setup section
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
6wwwgrassvalleycom
Installation on K2 Dyno S (cont)
16) With Windows Explorer open the RTDyno_Install folder and drag the tOGGVDynoClientcrx file onto the Chrome Browser window
17) In the Chrome Browser Apps tab is the RT Software Client app Right-click and select Create shortcutshellip
hellipand only check the Desktop box Then click Create Now close the Chrome browser The RT Software Client shortcut will be created on the desktop (NOTE Do Not check add to Start Menu or Pin to Taskbar this will create an incorrect shortcut)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
7wwwgrassvalleycom
Installation on K2 Dyno S (cont)
18) On the K2 Dyno S desktop right-click and create a new text file
19) Name the file the IP address of the tOG server PC and include the txt suf-fix (For this example the IP address is 10164179 therefore the file name would be 10164179txt Please remember to substitute your IP address for the example given)
20) Right-click on the RT Software Client short-cut and select Properties
21) In the Target field there should be a sim-ilar line to this ldquoCProgram Files (x86)GoogleChromeApplicationchromeexerdquo --profile-directory=Default --app-id=hdin-gebnoinafgkhbbdfdfobnanfopjo
22) At the end of this string add a single space and then ldquocUsersAdministratorDesk-top10164179txtrdquo Then click Apply and OK (Note Do not forget the quotation marks and to substitute your IP address for the example given above)
23) If the IP address of the tOG server PC changes in the future the txt file name and the target line above both need to be changed as well
24) After these settings are complete it is acceptable to add the shortcut to the Win-dows Taskbar
25) Once installation is complete ENABLE McAfee Embedded Security by selecting Leave Update Mode
26) Restart the K2 Dyno S controller
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
8wwwgrassvalleycom
Installation on K2 Summit 3G
1) Launch AppCenter on the on the K2 Summit 3G
2) Do not have a session in use Select the channel to be used and set it as PlayerRecorder
3) At the top of AppCenter select the Control tab and then Optionshellip
4) In the side tabs select Control and button check Remote and Local and AMP
5) Click OK
6) Do this for each channel to be con-trolled
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
9wwwgrassvalleycom
Installation on tOG Server
MySQL Installation
1) Installation of the DVS driver is required after installing the DVS IO hardware It can be performed after the tOG software installation See the end of this document for those procedures
2) Prior to installation the operating system has to be installed Current versions supported are
RedHat EL 55 Workstation 64-bit
Windows 7 Pro 64-bit SP1
3) Once the OS has been installed the NVIDIA driver has to be installed These must be obtained from the NVIDIA website wwwnvidiacom Current versions are
Linux ndash 33120
Windows ndash 33182
4) Refer to the documentation associated with the selected driver for install instructions
Installation of tOG Sports for Windows and Windows Projects require MySQL If not included in the GV Sports download zip download the MySQL install from the MySQL website This is located at
wwwmysqlcomdownloadsmysql
This is the community edition and is available for free under the Open Source GPL license
1) Double click on the installer
2) Click Next
3) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
10wwwgrassvalleycom
MySQL Installation (cont)
4) Typical is the setup type to be installed Click Next
5) Click Install
7) Click Next
6) MySQL will now install
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
11wwwgrassvalleycom
MySQL Installation (cont)
8) Click Next
11) Click Next
9) Click Finish
10) MySQL will now launch the MySQL Instance configurator
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
12wwwgrassvalleycom
MySQL Installation (cont)
12) Select Standard Configuration then Click Next
15) IMPORTANT Deselect the Modify Secu-rity Settings
16) Click Next
13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH
14) Click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
13wwwgrassvalleycom
MySQL Installation (cont)
17) MySQL service is ready to execute the con-figuration
18) Click Execute to finalize the installation and configuration of MySQL
19) Click Finish when the service is complete then close all open windows
20) Run the tOG Pre install application
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
14wwwgrassvalleycom
MySQL Installation (cont)
23) Click Finish to complete the installation
24) Run the tOG install application
25) Accept the EULA and click Next
26) Use the default installation directory loca-tion and click Next
27) Click Finish to complete the installation
28) Run the GV Sports Install application
29) Accept the EULA and click Next
30) Use the default Installation Directory loca-tion and click Next
31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next
32) Click Next again to start the install
33) Click Finish to complete the installation
34) On the desktop is a folder with the tOG ver-sion name
22) Use the default Installation Directory loca-tion and click Next
21) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
15wwwgrassvalleycom
MySQL Installation (cont)
36) The GV Sports shortcut can be copied to the desktop
37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server
38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server
39) Launch GV Sports with the desktop shortcut
35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall
40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab
41) Under Clip Control Plugin select K2DirClipStore
42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)
43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)
44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels
45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels
46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
16wwwgrassvalleycom
MySQL Installation (cont)
48) From the right hand panel of tabs select tOG Preferences
49) Under the Protocol tab None should be the Protocol setting
50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes
47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List
51) Under the Video tab choose the input and output device settings
52) If using the split screen tool the Number of Channels on the input side should be set to 2
53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter
54) Click Save to save any changes
55) Exit the tOG application and relaunch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
17wwwgrassvalleycom
MySQL Installation (cont)
56) IMPORTANT Xitami Web Server service must be stopped on the tOG server
Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server
57) Right-click Properties and under Gen-eral tab Startup type set to Disable
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
18wwwgrassvalleycom
MySQL Installation (cont)
58) Then ensure Service Status is STOPPED Click Apply and close the window
59) Next verify the Windows Firewall is turned OFF
60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing
61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process
62) Close all windows
63) Restart the tOG server
64) Launch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
2wwwgrassvalleycom
WHY tOG ON K2 DYNO S
The speed of live events and the need to efficiently tell the story of ldquowhat just happenedrdquo is increasingly in demand to be faster more dynamic paint a clearer picture and even be more entertaining to enhance the viewing experience The integration of tOG and K2 Dyno brings an affordable A-level analysis tool to every level of live event production
This Application Note covers
bull Software installation and setup on K2 Dyno S
bull Software installation and setup on the tOG PC
bull Preparing the K2 Summit 3G for interaction with tOG
bull Using the K2 Dyno StOG interface
bull Building stacked overlay graphics
Prior to using this Application Note verify with the K2 Dyno S K2 Summit 3G and tOG release notes that the appropriately compati-ble versions of software on all systems is being used Visit the Grass Valley K2 Dyno website for updated information regarding software releases required software and documentation wwwgrassvalleycomproductsk2_dyno and click on the Documentation tab in the Resources area
Required software for K2 Dyno installation in the RTDyno_Installzip file
ChromeStandaloneSetupexe
GoogleUpdateadm
tOGGVDynoClientcrx
tOGGVDynoClientpem
Required software for tOG Server installation
togpre-46_14565-windows-installer
tog-46_r15288-windows-installer
mysql-5535-winx64
dvsdriver-4354_1-windows-installer
gvsports-46_r15288-windows-installer
Have the IP address subnet mask and any other IP configuration information readily available for the K2 Dyno S K2 Summit 3G and tOG server In either a standalone or SAN configuration the K2 Dyno S K2 Summit 3G and tOG server need to be connected via a Gigabit Ethernet switch or router
For this Application Note example the IP addresses are
K2 Summit 3G 10164170
K2 Dyno S 10164171
tOG server PC 10164179
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
3wwwgrassvalleycom
Installation on K2 Dyno S
1) If the K2 Dyno application is running exit the application to the K2 Dyno S Mainte-nance level in order to see the Windows desktop
2) Verify that McAfee Embedded Security Manager is set to UPDATE
3) If not connected connect the K2 Dyno S Controller to the Internet via the Media Port on the back
4) Insert a USB device with the RTDyno_Install files
5) Run the ChromeStandaloneSetupexe
6) With an Internet connection Chrome will install on the K2 Dyno S controller Close the Chrome Browser application From this point Internet connection is no lon-ger required
7) To prevent Chrome from automatically downloading and installing updates that have not been tested in this environment it is advised the following adjustments to Chrome are made Use Windows Start menu and type in Edit group policy
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
4wwwgrassvalleycom
Installation on K2 Dyno S (cont)
8) From the selection click on Edit group policy When the window opens under User Configuration right-click on Administrative Templates then AddRemove Templates
9) Click Addhellip and browse to the RTDyno_Install folder that contains the file GoogleUpdateadm and select it and click Open
10) If it is listed in the window of tem-plates close the window
11) Under Computer Configuration select Administrative TemplatesClas-sic Administrative TemplatesGoogleGoogle UpdateApplications Google Chrome
12) In this folder right-click on Update policy override and select Edit
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
5wwwgrassvalleycom
Installation on K2 Dyno S (cont)
13) Change Update policy override to Enabled and Policy to Updates disabled
14) Then click Apply and then OK close all windows
15) Open a Chrome browser window and type in the URL search field chromeextensions This will open the Chrome extensions setup section
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
6wwwgrassvalleycom
Installation on K2 Dyno S (cont)
16) With Windows Explorer open the RTDyno_Install folder and drag the tOGGVDynoClientcrx file onto the Chrome Browser window
17) In the Chrome Browser Apps tab is the RT Software Client app Right-click and select Create shortcutshellip
hellipand only check the Desktop box Then click Create Now close the Chrome browser The RT Software Client shortcut will be created on the desktop (NOTE Do Not check add to Start Menu or Pin to Taskbar this will create an incorrect shortcut)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
7wwwgrassvalleycom
Installation on K2 Dyno S (cont)
18) On the K2 Dyno S desktop right-click and create a new text file
19) Name the file the IP address of the tOG server PC and include the txt suf-fix (For this example the IP address is 10164179 therefore the file name would be 10164179txt Please remember to substitute your IP address for the example given)
20) Right-click on the RT Software Client short-cut and select Properties
21) In the Target field there should be a sim-ilar line to this ldquoCProgram Files (x86)GoogleChromeApplicationchromeexerdquo --profile-directory=Default --app-id=hdin-gebnoinafgkhbbdfdfobnanfopjo
22) At the end of this string add a single space and then ldquocUsersAdministratorDesk-top10164179txtrdquo Then click Apply and OK (Note Do not forget the quotation marks and to substitute your IP address for the example given above)
23) If the IP address of the tOG server PC changes in the future the txt file name and the target line above both need to be changed as well
24) After these settings are complete it is acceptable to add the shortcut to the Win-dows Taskbar
25) Once installation is complete ENABLE McAfee Embedded Security by selecting Leave Update Mode
26) Restart the K2 Dyno S controller
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
8wwwgrassvalleycom
Installation on K2 Summit 3G
1) Launch AppCenter on the on the K2 Summit 3G
2) Do not have a session in use Select the channel to be used and set it as PlayerRecorder
3) At the top of AppCenter select the Control tab and then Optionshellip
4) In the side tabs select Control and button check Remote and Local and AMP
5) Click OK
6) Do this for each channel to be con-trolled
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
9wwwgrassvalleycom
Installation on tOG Server
MySQL Installation
1) Installation of the DVS driver is required after installing the DVS IO hardware It can be performed after the tOG software installation See the end of this document for those procedures
2) Prior to installation the operating system has to be installed Current versions supported are
RedHat EL 55 Workstation 64-bit
Windows 7 Pro 64-bit SP1
3) Once the OS has been installed the NVIDIA driver has to be installed These must be obtained from the NVIDIA website wwwnvidiacom Current versions are
Linux ndash 33120
Windows ndash 33182
4) Refer to the documentation associated with the selected driver for install instructions
Installation of tOG Sports for Windows and Windows Projects require MySQL If not included in the GV Sports download zip download the MySQL install from the MySQL website This is located at
wwwmysqlcomdownloadsmysql
This is the community edition and is available for free under the Open Source GPL license
1) Double click on the installer
2) Click Next
3) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
10wwwgrassvalleycom
MySQL Installation (cont)
4) Typical is the setup type to be installed Click Next
5) Click Install
7) Click Next
6) MySQL will now install
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
11wwwgrassvalleycom
MySQL Installation (cont)
8) Click Next
11) Click Next
9) Click Finish
10) MySQL will now launch the MySQL Instance configurator
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
12wwwgrassvalleycom
MySQL Installation (cont)
12) Select Standard Configuration then Click Next
15) IMPORTANT Deselect the Modify Secu-rity Settings
16) Click Next
13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH
14) Click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
13wwwgrassvalleycom
MySQL Installation (cont)
17) MySQL service is ready to execute the con-figuration
18) Click Execute to finalize the installation and configuration of MySQL
19) Click Finish when the service is complete then close all open windows
20) Run the tOG Pre install application
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
14wwwgrassvalleycom
MySQL Installation (cont)
23) Click Finish to complete the installation
24) Run the tOG install application
25) Accept the EULA and click Next
26) Use the default installation directory loca-tion and click Next
27) Click Finish to complete the installation
28) Run the GV Sports Install application
29) Accept the EULA and click Next
30) Use the default Installation Directory loca-tion and click Next
31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next
32) Click Next again to start the install
33) Click Finish to complete the installation
34) On the desktop is a folder with the tOG ver-sion name
22) Use the default Installation Directory loca-tion and click Next
21) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
15wwwgrassvalleycom
MySQL Installation (cont)
36) The GV Sports shortcut can be copied to the desktop
37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server
38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server
39) Launch GV Sports with the desktop shortcut
35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall
40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab
41) Under Clip Control Plugin select K2DirClipStore
42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)
43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)
44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels
45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels
46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
16wwwgrassvalleycom
MySQL Installation (cont)
48) From the right hand panel of tabs select tOG Preferences
49) Under the Protocol tab None should be the Protocol setting
50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes
47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List
51) Under the Video tab choose the input and output device settings
52) If using the split screen tool the Number of Channels on the input side should be set to 2
53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter
54) Click Save to save any changes
55) Exit the tOG application and relaunch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
17wwwgrassvalleycom
MySQL Installation (cont)
56) IMPORTANT Xitami Web Server service must be stopped on the tOG server
Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server
57) Right-click Properties and under Gen-eral tab Startup type set to Disable
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
18wwwgrassvalleycom
MySQL Installation (cont)
58) Then ensure Service Status is STOPPED Click Apply and close the window
59) Next verify the Windows Firewall is turned OFF
60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing
61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process
62) Close all windows
63) Restart the tOG server
64) Launch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
3wwwgrassvalleycom
Installation on K2 Dyno S
1) If the K2 Dyno application is running exit the application to the K2 Dyno S Mainte-nance level in order to see the Windows desktop
2) Verify that McAfee Embedded Security Manager is set to UPDATE
3) If not connected connect the K2 Dyno S Controller to the Internet via the Media Port on the back
4) Insert a USB device with the RTDyno_Install files
5) Run the ChromeStandaloneSetupexe
6) With an Internet connection Chrome will install on the K2 Dyno S controller Close the Chrome Browser application From this point Internet connection is no lon-ger required
7) To prevent Chrome from automatically downloading and installing updates that have not been tested in this environment it is advised the following adjustments to Chrome are made Use Windows Start menu and type in Edit group policy
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
4wwwgrassvalleycom
Installation on K2 Dyno S (cont)
8) From the selection click on Edit group policy When the window opens under User Configuration right-click on Administrative Templates then AddRemove Templates
9) Click Addhellip and browse to the RTDyno_Install folder that contains the file GoogleUpdateadm and select it and click Open
10) If it is listed in the window of tem-plates close the window
11) Under Computer Configuration select Administrative TemplatesClas-sic Administrative TemplatesGoogleGoogle UpdateApplications Google Chrome
12) In this folder right-click on Update policy override and select Edit
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
5wwwgrassvalleycom
Installation on K2 Dyno S (cont)
13) Change Update policy override to Enabled and Policy to Updates disabled
14) Then click Apply and then OK close all windows
15) Open a Chrome browser window and type in the URL search field chromeextensions This will open the Chrome extensions setup section
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
6wwwgrassvalleycom
Installation on K2 Dyno S (cont)
16) With Windows Explorer open the RTDyno_Install folder and drag the tOGGVDynoClientcrx file onto the Chrome Browser window
17) In the Chrome Browser Apps tab is the RT Software Client app Right-click and select Create shortcutshellip
hellipand only check the Desktop box Then click Create Now close the Chrome browser The RT Software Client shortcut will be created on the desktop (NOTE Do Not check add to Start Menu or Pin to Taskbar this will create an incorrect shortcut)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
7wwwgrassvalleycom
Installation on K2 Dyno S (cont)
18) On the K2 Dyno S desktop right-click and create a new text file
19) Name the file the IP address of the tOG server PC and include the txt suf-fix (For this example the IP address is 10164179 therefore the file name would be 10164179txt Please remember to substitute your IP address for the example given)
20) Right-click on the RT Software Client short-cut and select Properties
21) In the Target field there should be a sim-ilar line to this ldquoCProgram Files (x86)GoogleChromeApplicationchromeexerdquo --profile-directory=Default --app-id=hdin-gebnoinafgkhbbdfdfobnanfopjo
22) At the end of this string add a single space and then ldquocUsersAdministratorDesk-top10164179txtrdquo Then click Apply and OK (Note Do not forget the quotation marks and to substitute your IP address for the example given above)
23) If the IP address of the tOG server PC changes in the future the txt file name and the target line above both need to be changed as well
24) After these settings are complete it is acceptable to add the shortcut to the Win-dows Taskbar
25) Once installation is complete ENABLE McAfee Embedded Security by selecting Leave Update Mode
26) Restart the K2 Dyno S controller
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
8wwwgrassvalleycom
Installation on K2 Summit 3G
1) Launch AppCenter on the on the K2 Summit 3G
2) Do not have a session in use Select the channel to be used and set it as PlayerRecorder
3) At the top of AppCenter select the Control tab and then Optionshellip
4) In the side tabs select Control and button check Remote and Local and AMP
5) Click OK
6) Do this for each channel to be con-trolled
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
9wwwgrassvalleycom
Installation on tOG Server
MySQL Installation
1) Installation of the DVS driver is required after installing the DVS IO hardware It can be performed after the tOG software installation See the end of this document for those procedures
2) Prior to installation the operating system has to be installed Current versions supported are
RedHat EL 55 Workstation 64-bit
Windows 7 Pro 64-bit SP1
3) Once the OS has been installed the NVIDIA driver has to be installed These must be obtained from the NVIDIA website wwwnvidiacom Current versions are
Linux ndash 33120
Windows ndash 33182
4) Refer to the documentation associated with the selected driver for install instructions
Installation of tOG Sports for Windows and Windows Projects require MySQL If not included in the GV Sports download zip download the MySQL install from the MySQL website This is located at
wwwmysqlcomdownloadsmysql
This is the community edition and is available for free under the Open Source GPL license
1) Double click on the installer
2) Click Next
3) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
10wwwgrassvalleycom
MySQL Installation (cont)
4) Typical is the setup type to be installed Click Next
5) Click Install
7) Click Next
6) MySQL will now install
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
11wwwgrassvalleycom
MySQL Installation (cont)
8) Click Next
11) Click Next
9) Click Finish
10) MySQL will now launch the MySQL Instance configurator
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
12wwwgrassvalleycom
MySQL Installation (cont)
12) Select Standard Configuration then Click Next
15) IMPORTANT Deselect the Modify Secu-rity Settings
16) Click Next
13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH
14) Click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
13wwwgrassvalleycom
MySQL Installation (cont)
17) MySQL service is ready to execute the con-figuration
18) Click Execute to finalize the installation and configuration of MySQL
19) Click Finish when the service is complete then close all open windows
20) Run the tOG Pre install application
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
14wwwgrassvalleycom
MySQL Installation (cont)
23) Click Finish to complete the installation
24) Run the tOG install application
25) Accept the EULA and click Next
26) Use the default installation directory loca-tion and click Next
27) Click Finish to complete the installation
28) Run the GV Sports Install application
29) Accept the EULA and click Next
30) Use the default Installation Directory loca-tion and click Next
31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next
32) Click Next again to start the install
33) Click Finish to complete the installation
34) On the desktop is a folder with the tOG ver-sion name
22) Use the default Installation Directory loca-tion and click Next
21) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
15wwwgrassvalleycom
MySQL Installation (cont)
36) The GV Sports shortcut can be copied to the desktop
37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server
38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server
39) Launch GV Sports with the desktop shortcut
35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall
40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab
41) Under Clip Control Plugin select K2DirClipStore
42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)
43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)
44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels
45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels
46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
16wwwgrassvalleycom
MySQL Installation (cont)
48) From the right hand panel of tabs select tOG Preferences
49) Under the Protocol tab None should be the Protocol setting
50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes
47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List
51) Under the Video tab choose the input and output device settings
52) If using the split screen tool the Number of Channels on the input side should be set to 2
53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter
54) Click Save to save any changes
55) Exit the tOG application and relaunch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
17wwwgrassvalleycom
MySQL Installation (cont)
56) IMPORTANT Xitami Web Server service must be stopped on the tOG server
Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server
57) Right-click Properties and under Gen-eral tab Startup type set to Disable
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
18wwwgrassvalleycom
MySQL Installation (cont)
58) Then ensure Service Status is STOPPED Click Apply and close the window
59) Next verify the Windows Firewall is turned OFF
60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing
61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process
62) Close all windows
63) Restart the tOG server
64) Launch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
4wwwgrassvalleycom
Installation on K2 Dyno S (cont)
8) From the selection click on Edit group policy When the window opens under User Configuration right-click on Administrative Templates then AddRemove Templates
9) Click Addhellip and browse to the RTDyno_Install folder that contains the file GoogleUpdateadm and select it and click Open
10) If it is listed in the window of tem-plates close the window
11) Under Computer Configuration select Administrative TemplatesClas-sic Administrative TemplatesGoogleGoogle UpdateApplications Google Chrome
12) In this folder right-click on Update policy override and select Edit
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
5wwwgrassvalleycom
Installation on K2 Dyno S (cont)
13) Change Update policy override to Enabled and Policy to Updates disabled
14) Then click Apply and then OK close all windows
15) Open a Chrome browser window and type in the URL search field chromeextensions This will open the Chrome extensions setup section
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
6wwwgrassvalleycom
Installation on K2 Dyno S (cont)
16) With Windows Explorer open the RTDyno_Install folder and drag the tOGGVDynoClientcrx file onto the Chrome Browser window
17) In the Chrome Browser Apps tab is the RT Software Client app Right-click and select Create shortcutshellip
hellipand only check the Desktop box Then click Create Now close the Chrome browser The RT Software Client shortcut will be created on the desktop (NOTE Do Not check add to Start Menu or Pin to Taskbar this will create an incorrect shortcut)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
7wwwgrassvalleycom
Installation on K2 Dyno S (cont)
18) On the K2 Dyno S desktop right-click and create a new text file
19) Name the file the IP address of the tOG server PC and include the txt suf-fix (For this example the IP address is 10164179 therefore the file name would be 10164179txt Please remember to substitute your IP address for the example given)
20) Right-click on the RT Software Client short-cut and select Properties
21) In the Target field there should be a sim-ilar line to this ldquoCProgram Files (x86)GoogleChromeApplicationchromeexerdquo --profile-directory=Default --app-id=hdin-gebnoinafgkhbbdfdfobnanfopjo
22) At the end of this string add a single space and then ldquocUsersAdministratorDesk-top10164179txtrdquo Then click Apply and OK (Note Do not forget the quotation marks and to substitute your IP address for the example given above)
23) If the IP address of the tOG server PC changes in the future the txt file name and the target line above both need to be changed as well
24) After these settings are complete it is acceptable to add the shortcut to the Win-dows Taskbar
25) Once installation is complete ENABLE McAfee Embedded Security by selecting Leave Update Mode
26) Restart the K2 Dyno S controller
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
8wwwgrassvalleycom
Installation on K2 Summit 3G
1) Launch AppCenter on the on the K2 Summit 3G
2) Do not have a session in use Select the channel to be used and set it as PlayerRecorder
3) At the top of AppCenter select the Control tab and then Optionshellip
4) In the side tabs select Control and button check Remote and Local and AMP
5) Click OK
6) Do this for each channel to be con-trolled
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
9wwwgrassvalleycom
Installation on tOG Server
MySQL Installation
1) Installation of the DVS driver is required after installing the DVS IO hardware It can be performed after the tOG software installation See the end of this document for those procedures
2) Prior to installation the operating system has to be installed Current versions supported are
RedHat EL 55 Workstation 64-bit
Windows 7 Pro 64-bit SP1
3) Once the OS has been installed the NVIDIA driver has to be installed These must be obtained from the NVIDIA website wwwnvidiacom Current versions are
Linux ndash 33120
Windows ndash 33182
4) Refer to the documentation associated with the selected driver for install instructions
Installation of tOG Sports for Windows and Windows Projects require MySQL If not included in the GV Sports download zip download the MySQL install from the MySQL website This is located at
wwwmysqlcomdownloadsmysql
This is the community edition and is available for free under the Open Source GPL license
1) Double click on the installer
2) Click Next
3) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
10wwwgrassvalleycom
MySQL Installation (cont)
4) Typical is the setup type to be installed Click Next
5) Click Install
7) Click Next
6) MySQL will now install
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
11wwwgrassvalleycom
MySQL Installation (cont)
8) Click Next
11) Click Next
9) Click Finish
10) MySQL will now launch the MySQL Instance configurator
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
12wwwgrassvalleycom
MySQL Installation (cont)
12) Select Standard Configuration then Click Next
15) IMPORTANT Deselect the Modify Secu-rity Settings
16) Click Next
13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH
14) Click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
13wwwgrassvalleycom
MySQL Installation (cont)
17) MySQL service is ready to execute the con-figuration
18) Click Execute to finalize the installation and configuration of MySQL
19) Click Finish when the service is complete then close all open windows
20) Run the tOG Pre install application
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
14wwwgrassvalleycom
MySQL Installation (cont)
23) Click Finish to complete the installation
24) Run the tOG install application
25) Accept the EULA and click Next
26) Use the default installation directory loca-tion and click Next
27) Click Finish to complete the installation
28) Run the GV Sports Install application
29) Accept the EULA and click Next
30) Use the default Installation Directory loca-tion and click Next
31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next
32) Click Next again to start the install
33) Click Finish to complete the installation
34) On the desktop is a folder with the tOG ver-sion name
22) Use the default Installation Directory loca-tion and click Next
21) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
15wwwgrassvalleycom
MySQL Installation (cont)
36) The GV Sports shortcut can be copied to the desktop
37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server
38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server
39) Launch GV Sports with the desktop shortcut
35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall
40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab
41) Under Clip Control Plugin select K2DirClipStore
42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)
43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)
44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels
45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels
46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
16wwwgrassvalleycom
MySQL Installation (cont)
48) From the right hand panel of tabs select tOG Preferences
49) Under the Protocol tab None should be the Protocol setting
50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes
47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List
51) Under the Video tab choose the input and output device settings
52) If using the split screen tool the Number of Channels on the input side should be set to 2
53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter
54) Click Save to save any changes
55) Exit the tOG application and relaunch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
17wwwgrassvalleycom
MySQL Installation (cont)
56) IMPORTANT Xitami Web Server service must be stopped on the tOG server
Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server
57) Right-click Properties and under Gen-eral tab Startup type set to Disable
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
18wwwgrassvalleycom
MySQL Installation (cont)
58) Then ensure Service Status is STOPPED Click Apply and close the window
59) Next verify the Windows Firewall is turned OFF
60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing
61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process
62) Close all windows
63) Restart the tOG server
64) Launch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
5wwwgrassvalleycom
Installation on K2 Dyno S (cont)
13) Change Update policy override to Enabled and Policy to Updates disabled
14) Then click Apply and then OK close all windows
15) Open a Chrome browser window and type in the URL search field chromeextensions This will open the Chrome extensions setup section
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
6wwwgrassvalleycom
Installation on K2 Dyno S (cont)
16) With Windows Explorer open the RTDyno_Install folder and drag the tOGGVDynoClientcrx file onto the Chrome Browser window
17) In the Chrome Browser Apps tab is the RT Software Client app Right-click and select Create shortcutshellip
hellipand only check the Desktop box Then click Create Now close the Chrome browser The RT Software Client shortcut will be created on the desktop (NOTE Do Not check add to Start Menu or Pin to Taskbar this will create an incorrect shortcut)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
7wwwgrassvalleycom
Installation on K2 Dyno S (cont)
18) On the K2 Dyno S desktop right-click and create a new text file
19) Name the file the IP address of the tOG server PC and include the txt suf-fix (For this example the IP address is 10164179 therefore the file name would be 10164179txt Please remember to substitute your IP address for the example given)
20) Right-click on the RT Software Client short-cut and select Properties
21) In the Target field there should be a sim-ilar line to this ldquoCProgram Files (x86)GoogleChromeApplicationchromeexerdquo --profile-directory=Default --app-id=hdin-gebnoinafgkhbbdfdfobnanfopjo
22) At the end of this string add a single space and then ldquocUsersAdministratorDesk-top10164179txtrdquo Then click Apply and OK (Note Do not forget the quotation marks and to substitute your IP address for the example given above)
23) If the IP address of the tOG server PC changes in the future the txt file name and the target line above both need to be changed as well
24) After these settings are complete it is acceptable to add the shortcut to the Win-dows Taskbar
25) Once installation is complete ENABLE McAfee Embedded Security by selecting Leave Update Mode
26) Restart the K2 Dyno S controller
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
8wwwgrassvalleycom
Installation on K2 Summit 3G
1) Launch AppCenter on the on the K2 Summit 3G
2) Do not have a session in use Select the channel to be used and set it as PlayerRecorder
3) At the top of AppCenter select the Control tab and then Optionshellip
4) In the side tabs select Control and button check Remote and Local and AMP
5) Click OK
6) Do this for each channel to be con-trolled
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
9wwwgrassvalleycom
Installation on tOG Server
MySQL Installation
1) Installation of the DVS driver is required after installing the DVS IO hardware It can be performed after the tOG software installation See the end of this document for those procedures
2) Prior to installation the operating system has to be installed Current versions supported are
RedHat EL 55 Workstation 64-bit
Windows 7 Pro 64-bit SP1
3) Once the OS has been installed the NVIDIA driver has to be installed These must be obtained from the NVIDIA website wwwnvidiacom Current versions are
Linux ndash 33120
Windows ndash 33182
4) Refer to the documentation associated with the selected driver for install instructions
Installation of tOG Sports for Windows and Windows Projects require MySQL If not included in the GV Sports download zip download the MySQL install from the MySQL website This is located at
wwwmysqlcomdownloadsmysql
This is the community edition and is available for free under the Open Source GPL license
1) Double click on the installer
2) Click Next
3) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
10wwwgrassvalleycom
MySQL Installation (cont)
4) Typical is the setup type to be installed Click Next
5) Click Install
7) Click Next
6) MySQL will now install
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
11wwwgrassvalleycom
MySQL Installation (cont)
8) Click Next
11) Click Next
9) Click Finish
10) MySQL will now launch the MySQL Instance configurator
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
12wwwgrassvalleycom
MySQL Installation (cont)
12) Select Standard Configuration then Click Next
15) IMPORTANT Deselect the Modify Secu-rity Settings
16) Click Next
13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH
14) Click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
13wwwgrassvalleycom
MySQL Installation (cont)
17) MySQL service is ready to execute the con-figuration
18) Click Execute to finalize the installation and configuration of MySQL
19) Click Finish when the service is complete then close all open windows
20) Run the tOG Pre install application
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
14wwwgrassvalleycom
MySQL Installation (cont)
23) Click Finish to complete the installation
24) Run the tOG install application
25) Accept the EULA and click Next
26) Use the default installation directory loca-tion and click Next
27) Click Finish to complete the installation
28) Run the GV Sports Install application
29) Accept the EULA and click Next
30) Use the default Installation Directory loca-tion and click Next
31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next
32) Click Next again to start the install
33) Click Finish to complete the installation
34) On the desktop is a folder with the tOG ver-sion name
22) Use the default Installation Directory loca-tion and click Next
21) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
15wwwgrassvalleycom
MySQL Installation (cont)
36) The GV Sports shortcut can be copied to the desktop
37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server
38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server
39) Launch GV Sports with the desktop shortcut
35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall
40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab
41) Under Clip Control Plugin select K2DirClipStore
42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)
43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)
44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels
45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels
46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
16wwwgrassvalleycom
MySQL Installation (cont)
48) From the right hand panel of tabs select tOG Preferences
49) Under the Protocol tab None should be the Protocol setting
50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes
47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List
51) Under the Video tab choose the input and output device settings
52) If using the split screen tool the Number of Channels on the input side should be set to 2
53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter
54) Click Save to save any changes
55) Exit the tOG application and relaunch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
17wwwgrassvalleycom
MySQL Installation (cont)
56) IMPORTANT Xitami Web Server service must be stopped on the tOG server
Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server
57) Right-click Properties and under Gen-eral tab Startup type set to Disable
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
18wwwgrassvalleycom
MySQL Installation (cont)
58) Then ensure Service Status is STOPPED Click Apply and close the window
59) Next verify the Windows Firewall is turned OFF
60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing
61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process
62) Close all windows
63) Restart the tOG server
64) Launch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
6wwwgrassvalleycom
Installation on K2 Dyno S (cont)
16) With Windows Explorer open the RTDyno_Install folder and drag the tOGGVDynoClientcrx file onto the Chrome Browser window
17) In the Chrome Browser Apps tab is the RT Software Client app Right-click and select Create shortcutshellip
hellipand only check the Desktop box Then click Create Now close the Chrome browser The RT Software Client shortcut will be created on the desktop (NOTE Do Not check add to Start Menu or Pin to Taskbar this will create an incorrect shortcut)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
7wwwgrassvalleycom
Installation on K2 Dyno S (cont)
18) On the K2 Dyno S desktop right-click and create a new text file
19) Name the file the IP address of the tOG server PC and include the txt suf-fix (For this example the IP address is 10164179 therefore the file name would be 10164179txt Please remember to substitute your IP address for the example given)
20) Right-click on the RT Software Client short-cut and select Properties
21) In the Target field there should be a sim-ilar line to this ldquoCProgram Files (x86)GoogleChromeApplicationchromeexerdquo --profile-directory=Default --app-id=hdin-gebnoinafgkhbbdfdfobnanfopjo
22) At the end of this string add a single space and then ldquocUsersAdministratorDesk-top10164179txtrdquo Then click Apply and OK (Note Do not forget the quotation marks and to substitute your IP address for the example given above)
23) If the IP address of the tOG server PC changes in the future the txt file name and the target line above both need to be changed as well
24) After these settings are complete it is acceptable to add the shortcut to the Win-dows Taskbar
25) Once installation is complete ENABLE McAfee Embedded Security by selecting Leave Update Mode
26) Restart the K2 Dyno S controller
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
8wwwgrassvalleycom
Installation on K2 Summit 3G
1) Launch AppCenter on the on the K2 Summit 3G
2) Do not have a session in use Select the channel to be used and set it as PlayerRecorder
3) At the top of AppCenter select the Control tab and then Optionshellip
4) In the side tabs select Control and button check Remote and Local and AMP
5) Click OK
6) Do this for each channel to be con-trolled
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
9wwwgrassvalleycom
Installation on tOG Server
MySQL Installation
1) Installation of the DVS driver is required after installing the DVS IO hardware It can be performed after the tOG software installation See the end of this document for those procedures
2) Prior to installation the operating system has to be installed Current versions supported are
RedHat EL 55 Workstation 64-bit
Windows 7 Pro 64-bit SP1
3) Once the OS has been installed the NVIDIA driver has to be installed These must be obtained from the NVIDIA website wwwnvidiacom Current versions are
Linux ndash 33120
Windows ndash 33182
4) Refer to the documentation associated with the selected driver for install instructions
Installation of tOG Sports for Windows and Windows Projects require MySQL If not included in the GV Sports download zip download the MySQL install from the MySQL website This is located at
wwwmysqlcomdownloadsmysql
This is the community edition and is available for free under the Open Source GPL license
1) Double click on the installer
2) Click Next
3) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
10wwwgrassvalleycom
MySQL Installation (cont)
4) Typical is the setup type to be installed Click Next
5) Click Install
7) Click Next
6) MySQL will now install
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
11wwwgrassvalleycom
MySQL Installation (cont)
8) Click Next
11) Click Next
9) Click Finish
10) MySQL will now launch the MySQL Instance configurator
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
12wwwgrassvalleycom
MySQL Installation (cont)
12) Select Standard Configuration then Click Next
15) IMPORTANT Deselect the Modify Secu-rity Settings
16) Click Next
13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH
14) Click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
13wwwgrassvalleycom
MySQL Installation (cont)
17) MySQL service is ready to execute the con-figuration
18) Click Execute to finalize the installation and configuration of MySQL
19) Click Finish when the service is complete then close all open windows
20) Run the tOG Pre install application
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
14wwwgrassvalleycom
MySQL Installation (cont)
23) Click Finish to complete the installation
24) Run the tOG install application
25) Accept the EULA and click Next
26) Use the default installation directory loca-tion and click Next
27) Click Finish to complete the installation
28) Run the GV Sports Install application
29) Accept the EULA and click Next
30) Use the default Installation Directory loca-tion and click Next
31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next
32) Click Next again to start the install
33) Click Finish to complete the installation
34) On the desktop is a folder with the tOG ver-sion name
22) Use the default Installation Directory loca-tion and click Next
21) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
15wwwgrassvalleycom
MySQL Installation (cont)
36) The GV Sports shortcut can be copied to the desktop
37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server
38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server
39) Launch GV Sports with the desktop shortcut
35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall
40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab
41) Under Clip Control Plugin select K2DirClipStore
42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)
43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)
44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels
45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels
46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
16wwwgrassvalleycom
MySQL Installation (cont)
48) From the right hand panel of tabs select tOG Preferences
49) Under the Protocol tab None should be the Protocol setting
50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes
47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List
51) Under the Video tab choose the input and output device settings
52) If using the split screen tool the Number of Channels on the input side should be set to 2
53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter
54) Click Save to save any changes
55) Exit the tOG application and relaunch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
17wwwgrassvalleycom
MySQL Installation (cont)
56) IMPORTANT Xitami Web Server service must be stopped on the tOG server
Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server
57) Right-click Properties and under Gen-eral tab Startup type set to Disable
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
18wwwgrassvalleycom
MySQL Installation (cont)
58) Then ensure Service Status is STOPPED Click Apply and close the window
59) Next verify the Windows Firewall is turned OFF
60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing
61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process
62) Close all windows
63) Restart the tOG server
64) Launch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
7wwwgrassvalleycom
Installation on K2 Dyno S (cont)
18) On the K2 Dyno S desktop right-click and create a new text file
19) Name the file the IP address of the tOG server PC and include the txt suf-fix (For this example the IP address is 10164179 therefore the file name would be 10164179txt Please remember to substitute your IP address for the example given)
20) Right-click on the RT Software Client short-cut and select Properties
21) In the Target field there should be a sim-ilar line to this ldquoCProgram Files (x86)GoogleChromeApplicationchromeexerdquo --profile-directory=Default --app-id=hdin-gebnoinafgkhbbdfdfobnanfopjo
22) At the end of this string add a single space and then ldquocUsersAdministratorDesk-top10164179txtrdquo Then click Apply and OK (Note Do not forget the quotation marks and to substitute your IP address for the example given above)
23) If the IP address of the tOG server PC changes in the future the txt file name and the target line above both need to be changed as well
24) After these settings are complete it is acceptable to add the shortcut to the Win-dows Taskbar
25) Once installation is complete ENABLE McAfee Embedded Security by selecting Leave Update Mode
26) Restart the K2 Dyno S controller
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
8wwwgrassvalleycom
Installation on K2 Summit 3G
1) Launch AppCenter on the on the K2 Summit 3G
2) Do not have a session in use Select the channel to be used and set it as PlayerRecorder
3) At the top of AppCenter select the Control tab and then Optionshellip
4) In the side tabs select Control and button check Remote and Local and AMP
5) Click OK
6) Do this for each channel to be con-trolled
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
9wwwgrassvalleycom
Installation on tOG Server
MySQL Installation
1) Installation of the DVS driver is required after installing the DVS IO hardware It can be performed after the tOG software installation See the end of this document for those procedures
2) Prior to installation the operating system has to be installed Current versions supported are
RedHat EL 55 Workstation 64-bit
Windows 7 Pro 64-bit SP1
3) Once the OS has been installed the NVIDIA driver has to be installed These must be obtained from the NVIDIA website wwwnvidiacom Current versions are
Linux ndash 33120
Windows ndash 33182
4) Refer to the documentation associated with the selected driver for install instructions
Installation of tOG Sports for Windows and Windows Projects require MySQL If not included in the GV Sports download zip download the MySQL install from the MySQL website This is located at
wwwmysqlcomdownloadsmysql
This is the community edition and is available for free under the Open Source GPL license
1) Double click on the installer
2) Click Next
3) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
10wwwgrassvalleycom
MySQL Installation (cont)
4) Typical is the setup type to be installed Click Next
5) Click Install
7) Click Next
6) MySQL will now install
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
11wwwgrassvalleycom
MySQL Installation (cont)
8) Click Next
11) Click Next
9) Click Finish
10) MySQL will now launch the MySQL Instance configurator
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
12wwwgrassvalleycom
MySQL Installation (cont)
12) Select Standard Configuration then Click Next
15) IMPORTANT Deselect the Modify Secu-rity Settings
16) Click Next
13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH
14) Click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
13wwwgrassvalleycom
MySQL Installation (cont)
17) MySQL service is ready to execute the con-figuration
18) Click Execute to finalize the installation and configuration of MySQL
19) Click Finish when the service is complete then close all open windows
20) Run the tOG Pre install application
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
14wwwgrassvalleycom
MySQL Installation (cont)
23) Click Finish to complete the installation
24) Run the tOG install application
25) Accept the EULA and click Next
26) Use the default installation directory loca-tion and click Next
27) Click Finish to complete the installation
28) Run the GV Sports Install application
29) Accept the EULA and click Next
30) Use the default Installation Directory loca-tion and click Next
31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next
32) Click Next again to start the install
33) Click Finish to complete the installation
34) On the desktop is a folder with the tOG ver-sion name
22) Use the default Installation Directory loca-tion and click Next
21) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
15wwwgrassvalleycom
MySQL Installation (cont)
36) The GV Sports shortcut can be copied to the desktop
37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server
38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server
39) Launch GV Sports with the desktop shortcut
35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall
40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab
41) Under Clip Control Plugin select K2DirClipStore
42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)
43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)
44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels
45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels
46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
16wwwgrassvalleycom
MySQL Installation (cont)
48) From the right hand panel of tabs select tOG Preferences
49) Under the Protocol tab None should be the Protocol setting
50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes
47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List
51) Under the Video tab choose the input and output device settings
52) If using the split screen tool the Number of Channels on the input side should be set to 2
53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter
54) Click Save to save any changes
55) Exit the tOG application and relaunch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
17wwwgrassvalleycom
MySQL Installation (cont)
56) IMPORTANT Xitami Web Server service must be stopped on the tOG server
Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server
57) Right-click Properties and under Gen-eral tab Startup type set to Disable
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
18wwwgrassvalleycom
MySQL Installation (cont)
58) Then ensure Service Status is STOPPED Click Apply and close the window
59) Next verify the Windows Firewall is turned OFF
60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing
61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process
62) Close all windows
63) Restart the tOG server
64) Launch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
8wwwgrassvalleycom
Installation on K2 Summit 3G
1) Launch AppCenter on the on the K2 Summit 3G
2) Do not have a session in use Select the channel to be used and set it as PlayerRecorder
3) At the top of AppCenter select the Control tab and then Optionshellip
4) In the side tabs select Control and button check Remote and Local and AMP
5) Click OK
6) Do this for each channel to be con-trolled
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
9wwwgrassvalleycom
Installation on tOG Server
MySQL Installation
1) Installation of the DVS driver is required after installing the DVS IO hardware It can be performed after the tOG software installation See the end of this document for those procedures
2) Prior to installation the operating system has to be installed Current versions supported are
RedHat EL 55 Workstation 64-bit
Windows 7 Pro 64-bit SP1
3) Once the OS has been installed the NVIDIA driver has to be installed These must be obtained from the NVIDIA website wwwnvidiacom Current versions are
Linux ndash 33120
Windows ndash 33182
4) Refer to the documentation associated with the selected driver for install instructions
Installation of tOG Sports for Windows and Windows Projects require MySQL If not included in the GV Sports download zip download the MySQL install from the MySQL website This is located at
wwwmysqlcomdownloadsmysql
This is the community edition and is available for free under the Open Source GPL license
1) Double click on the installer
2) Click Next
3) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
10wwwgrassvalleycom
MySQL Installation (cont)
4) Typical is the setup type to be installed Click Next
5) Click Install
7) Click Next
6) MySQL will now install
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
11wwwgrassvalleycom
MySQL Installation (cont)
8) Click Next
11) Click Next
9) Click Finish
10) MySQL will now launch the MySQL Instance configurator
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
12wwwgrassvalleycom
MySQL Installation (cont)
12) Select Standard Configuration then Click Next
15) IMPORTANT Deselect the Modify Secu-rity Settings
16) Click Next
13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH
14) Click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
13wwwgrassvalleycom
MySQL Installation (cont)
17) MySQL service is ready to execute the con-figuration
18) Click Execute to finalize the installation and configuration of MySQL
19) Click Finish when the service is complete then close all open windows
20) Run the tOG Pre install application
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
14wwwgrassvalleycom
MySQL Installation (cont)
23) Click Finish to complete the installation
24) Run the tOG install application
25) Accept the EULA and click Next
26) Use the default installation directory loca-tion and click Next
27) Click Finish to complete the installation
28) Run the GV Sports Install application
29) Accept the EULA and click Next
30) Use the default Installation Directory loca-tion and click Next
31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next
32) Click Next again to start the install
33) Click Finish to complete the installation
34) On the desktop is a folder with the tOG ver-sion name
22) Use the default Installation Directory loca-tion and click Next
21) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
15wwwgrassvalleycom
MySQL Installation (cont)
36) The GV Sports shortcut can be copied to the desktop
37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server
38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server
39) Launch GV Sports with the desktop shortcut
35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall
40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab
41) Under Clip Control Plugin select K2DirClipStore
42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)
43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)
44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels
45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels
46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
16wwwgrassvalleycom
MySQL Installation (cont)
48) From the right hand panel of tabs select tOG Preferences
49) Under the Protocol tab None should be the Protocol setting
50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes
47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List
51) Under the Video tab choose the input and output device settings
52) If using the split screen tool the Number of Channels on the input side should be set to 2
53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter
54) Click Save to save any changes
55) Exit the tOG application and relaunch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
17wwwgrassvalleycom
MySQL Installation (cont)
56) IMPORTANT Xitami Web Server service must be stopped on the tOG server
Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server
57) Right-click Properties and under Gen-eral tab Startup type set to Disable
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
18wwwgrassvalleycom
MySQL Installation (cont)
58) Then ensure Service Status is STOPPED Click Apply and close the window
59) Next verify the Windows Firewall is turned OFF
60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing
61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process
62) Close all windows
63) Restart the tOG server
64) Launch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
9wwwgrassvalleycom
Installation on tOG Server
MySQL Installation
1) Installation of the DVS driver is required after installing the DVS IO hardware It can be performed after the tOG software installation See the end of this document for those procedures
2) Prior to installation the operating system has to be installed Current versions supported are
RedHat EL 55 Workstation 64-bit
Windows 7 Pro 64-bit SP1
3) Once the OS has been installed the NVIDIA driver has to be installed These must be obtained from the NVIDIA website wwwnvidiacom Current versions are
Linux ndash 33120
Windows ndash 33182
4) Refer to the documentation associated with the selected driver for install instructions
Installation of tOG Sports for Windows and Windows Projects require MySQL If not included in the GV Sports download zip download the MySQL install from the MySQL website This is located at
wwwmysqlcomdownloadsmysql
This is the community edition and is available for free under the Open Source GPL license
1) Double click on the installer
2) Click Next
3) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
10wwwgrassvalleycom
MySQL Installation (cont)
4) Typical is the setup type to be installed Click Next
5) Click Install
7) Click Next
6) MySQL will now install
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
11wwwgrassvalleycom
MySQL Installation (cont)
8) Click Next
11) Click Next
9) Click Finish
10) MySQL will now launch the MySQL Instance configurator
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
12wwwgrassvalleycom
MySQL Installation (cont)
12) Select Standard Configuration then Click Next
15) IMPORTANT Deselect the Modify Secu-rity Settings
16) Click Next
13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH
14) Click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
13wwwgrassvalleycom
MySQL Installation (cont)
17) MySQL service is ready to execute the con-figuration
18) Click Execute to finalize the installation and configuration of MySQL
19) Click Finish when the service is complete then close all open windows
20) Run the tOG Pre install application
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
14wwwgrassvalleycom
MySQL Installation (cont)
23) Click Finish to complete the installation
24) Run the tOG install application
25) Accept the EULA and click Next
26) Use the default installation directory loca-tion and click Next
27) Click Finish to complete the installation
28) Run the GV Sports Install application
29) Accept the EULA and click Next
30) Use the default Installation Directory loca-tion and click Next
31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next
32) Click Next again to start the install
33) Click Finish to complete the installation
34) On the desktop is a folder with the tOG ver-sion name
22) Use the default Installation Directory loca-tion and click Next
21) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
15wwwgrassvalleycom
MySQL Installation (cont)
36) The GV Sports shortcut can be copied to the desktop
37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server
38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server
39) Launch GV Sports with the desktop shortcut
35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall
40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab
41) Under Clip Control Plugin select K2DirClipStore
42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)
43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)
44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels
45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels
46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
16wwwgrassvalleycom
MySQL Installation (cont)
48) From the right hand panel of tabs select tOG Preferences
49) Under the Protocol tab None should be the Protocol setting
50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes
47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List
51) Under the Video tab choose the input and output device settings
52) If using the split screen tool the Number of Channels on the input side should be set to 2
53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter
54) Click Save to save any changes
55) Exit the tOG application and relaunch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
17wwwgrassvalleycom
MySQL Installation (cont)
56) IMPORTANT Xitami Web Server service must be stopped on the tOG server
Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server
57) Right-click Properties and under Gen-eral tab Startup type set to Disable
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
18wwwgrassvalleycom
MySQL Installation (cont)
58) Then ensure Service Status is STOPPED Click Apply and close the window
59) Next verify the Windows Firewall is turned OFF
60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing
61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process
62) Close all windows
63) Restart the tOG server
64) Launch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
10wwwgrassvalleycom
MySQL Installation (cont)
4) Typical is the setup type to be installed Click Next
5) Click Install
7) Click Next
6) MySQL will now install
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
11wwwgrassvalleycom
MySQL Installation (cont)
8) Click Next
11) Click Next
9) Click Finish
10) MySQL will now launch the MySQL Instance configurator
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
12wwwgrassvalleycom
MySQL Installation (cont)
12) Select Standard Configuration then Click Next
15) IMPORTANT Deselect the Modify Secu-rity Settings
16) Click Next
13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH
14) Click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
13wwwgrassvalleycom
MySQL Installation (cont)
17) MySQL service is ready to execute the con-figuration
18) Click Execute to finalize the installation and configuration of MySQL
19) Click Finish when the service is complete then close all open windows
20) Run the tOG Pre install application
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
14wwwgrassvalleycom
MySQL Installation (cont)
23) Click Finish to complete the installation
24) Run the tOG install application
25) Accept the EULA and click Next
26) Use the default installation directory loca-tion and click Next
27) Click Finish to complete the installation
28) Run the GV Sports Install application
29) Accept the EULA and click Next
30) Use the default Installation Directory loca-tion and click Next
31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next
32) Click Next again to start the install
33) Click Finish to complete the installation
34) On the desktop is a folder with the tOG ver-sion name
22) Use the default Installation Directory loca-tion and click Next
21) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
15wwwgrassvalleycom
MySQL Installation (cont)
36) The GV Sports shortcut can be copied to the desktop
37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server
38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server
39) Launch GV Sports with the desktop shortcut
35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall
40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab
41) Under Clip Control Plugin select K2DirClipStore
42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)
43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)
44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels
45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels
46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
16wwwgrassvalleycom
MySQL Installation (cont)
48) From the right hand panel of tabs select tOG Preferences
49) Under the Protocol tab None should be the Protocol setting
50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes
47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List
51) Under the Video tab choose the input and output device settings
52) If using the split screen tool the Number of Channels on the input side should be set to 2
53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter
54) Click Save to save any changes
55) Exit the tOG application and relaunch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
17wwwgrassvalleycom
MySQL Installation (cont)
56) IMPORTANT Xitami Web Server service must be stopped on the tOG server
Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server
57) Right-click Properties and under Gen-eral tab Startup type set to Disable
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
18wwwgrassvalleycom
MySQL Installation (cont)
58) Then ensure Service Status is STOPPED Click Apply and close the window
59) Next verify the Windows Firewall is turned OFF
60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing
61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process
62) Close all windows
63) Restart the tOG server
64) Launch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
11wwwgrassvalleycom
MySQL Installation (cont)
8) Click Next
11) Click Next
9) Click Finish
10) MySQL will now launch the MySQL Instance configurator
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
12wwwgrassvalleycom
MySQL Installation (cont)
12) Select Standard Configuration then Click Next
15) IMPORTANT Deselect the Modify Secu-rity Settings
16) Click Next
13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH
14) Click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
13wwwgrassvalleycom
MySQL Installation (cont)
17) MySQL service is ready to execute the con-figuration
18) Click Execute to finalize the installation and configuration of MySQL
19) Click Finish when the service is complete then close all open windows
20) Run the tOG Pre install application
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
14wwwgrassvalleycom
MySQL Installation (cont)
23) Click Finish to complete the installation
24) Run the tOG install application
25) Accept the EULA and click Next
26) Use the default installation directory loca-tion and click Next
27) Click Finish to complete the installation
28) Run the GV Sports Install application
29) Accept the EULA and click Next
30) Use the default Installation Directory loca-tion and click Next
31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next
32) Click Next again to start the install
33) Click Finish to complete the installation
34) On the desktop is a folder with the tOG ver-sion name
22) Use the default Installation Directory loca-tion and click Next
21) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
15wwwgrassvalleycom
MySQL Installation (cont)
36) The GV Sports shortcut can be copied to the desktop
37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server
38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server
39) Launch GV Sports with the desktop shortcut
35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall
40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab
41) Under Clip Control Plugin select K2DirClipStore
42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)
43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)
44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels
45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels
46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
16wwwgrassvalleycom
MySQL Installation (cont)
48) From the right hand panel of tabs select tOG Preferences
49) Under the Protocol tab None should be the Protocol setting
50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes
47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List
51) Under the Video tab choose the input and output device settings
52) If using the split screen tool the Number of Channels on the input side should be set to 2
53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter
54) Click Save to save any changes
55) Exit the tOG application and relaunch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
17wwwgrassvalleycom
MySQL Installation (cont)
56) IMPORTANT Xitami Web Server service must be stopped on the tOG server
Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server
57) Right-click Properties and under Gen-eral tab Startup type set to Disable
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
18wwwgrassvalleycom
MySQL Installation (cont)
58) Then ensure Service Status is STOPPED Click Apply and close the window
59) Next verify the Windows Firewall is turned OFF
60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing
61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process
62) Close all windows
63) Restart the tOG server
64) Launch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
12wwwgrassvalleycom
MySQL Installation (cont)
12) Select Standard Configuration then Click Next
15) IMPORTANT Deselect the Modify Secu-rity Settings
16) Click Next
13) Check both boxes for Install As Windows Service and Include Bin Directory in Win-dows PATH
14) Click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
13wwwgrassvalleycom
MySQL Installation (cont)
17) MySQL service is ready to execute the con-figuration
18) Click Execute to finalize the installation and configuration of MySQL
19) Click Finish when the service is complete then close all open windows
20) Run the tOG Pre install application
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
14wwwgrassvalleycom
MySQL Installation (cont)
23) Click Finish to complete the installation
24) Run the tOG install application
25) Accept the EULA and click Next
26) Use the default installation directory loca-tion and click Next
27) Click Finish to complete the installation
28) Run the GV Sports Install application
29) Accept the EULA and click Next
30) Use the default Installation Directory loca-tion and click Next
31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next
32) Click Next again to start the install
33) Click Finish to complete the installation
34) On the desktop is a folder with the tOG ver-sion name
22) Use the default Installation Directory loca-tion and click Next
21) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
15wwwgrassvalleycom
MySQL Installation (cont)
36) The GV Sports shortcut can be copied to the desktop
37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server
38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server
39) Launch GV Sports with the desktop shortcut
35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall
40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab
41) Under Clip Control Plugin select K2DirClipStore
42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)
43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)
44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels
45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels
46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
16wwwgrassvalleycom
MySQL Installation (cont)
48) From the right hand panel of tabs select tOG Preferences
49) Under the Protocol tab None should be the Protocol setting
50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes
47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List
51) Under the Video tab choose the input and output device settings
52) If using the split screen tool the Number of Channels on the input side should be set to 2
53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter
54) Click Save to save any changes
55) Exit the tOG application and relaunch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
17wwwgrassvalleycom
MySQL Installation (cont)
56) IMPORTANT Xitami Web Server service must be stopped on the tOG server
Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server
57) Right-click Properties and under Gen-eral tab Startup type set to Disable
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
18wwwgrassvalleycom
MySQL Installation (cont)
58) Then ensure Service Status is STOPPED Click Apply and close the window
59) Next verify the Windows Firewall is turned OFF
60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing
61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process
62) Close all windows
63) Restart the tOG server
64) Launch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
13wwwgrassvalleycom
MySQL Installation (cont)
17) MySQL service is ready to execute the con-figuration
18) Click Execute to finalize the installation and configuration of MySQL
19) Click Finish when the service is complete then close all open windows
20) Run the tOG Pre install application
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
14wwwgrassvalleycom
MySQL Installation (cont)
23) Click Finish to complete the installation
24) Run the tOG install application
25) Accept the EULA and click Next
26) Use the default installation directory loca-tion and click Next
27) Click Finish to complete the installation
28) Run the GV Sports Install application
29) Accept the EULA and click Next
30) Use the default Installation Directory loca-tion and click Next
31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next
32) Click Next again to start the install
33) Click Finish to complete the installation
34) On the desktop is a folder with the tOG ver-sion name
22) Use the default Installation Directory loca-tion and click Next
21) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
15wwwgrassvalleycom
MySQL Installation (cont)
36) The GV Sports shortcut can be copied to the desktop
37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server
38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server
39) Launch GV Sports with the desktop shortcut
35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall
40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab
41) Under Clip Control Plugin select K2DirClipStore
42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)
43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)
44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels
45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels
46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
16wwwgrassvalleycom
MySQL Installation (cont)
48) From the right hand panel of tabs select tOG Preferences
49) Under the Protocol tab None should be the Protocol setting
50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes
47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List
51) Under the Video tab choose the input and output device settings
52) If using the split screen tool the Number of Channels on the input side should be set to 2
53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter
54) Click Save to save any changes
55) Exit the tOG application and relaunch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
17wwwgrassvalleycom
MySQL Installation (cont)
56) IMPORTANT Xitami Web Server service must be stopped on the tOG server
Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server
57) Right-click Properties and under Gen-eral tab Startup type set to Disable
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
18wwwgrassvalleycom
MySQL Installation (cont)
58) Then ensure Service Status is STOPPED Click Apply and close the window
59) Next verify the Windows Firewall is turned OFF
60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing
61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process
62) Close all windows
63) Restart the tOG server
64) Launch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
14wwwgrassvalleycom
MySQL Installation (cont)
23) Click Finish to complete the installation
24) Run the tOG install application
25) Accept the EULA and click Next
26) Use the default installation directory loca-tion and click Next
27) Click Finish to complete the installation
28) Run the GV Sports Install application
29) Accept the EULA and click Next
30) Use the default Installation Directory loca-tion and click Next
31) DO NOT enter a password for Root pass-word for mysql It needs to remain blank Click Next
32) Click Next again to start the install
33) Click Finish to complete the installation
34) On the desktop is a folder with the tOG ver-sion name
22) Use the default Installation Directory loca-tion and click Next
21) Accept the EULA and click Next
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
15wwwgrassvalleycom
MySQL Installation (cont)
36) The GV Sports shortcut can be copied to the desktop
37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server
38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server
39) Launch GV Sports with the desktop shortcut
35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall
40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab
41) Under Clip Control Plugin select K2DirClipStore
42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)
43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)
44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels
45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels
46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
16wwwgrassvalleycom
MySQL Installation (cont)
48) From the right hand panel of tabs select tOG Preferences
49) Under the Protocol tab None should be the Protocol setting
50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes
47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List
51) Under the Video tab choose the input and output device settings
52) If using the split screen tool the Number of Channels on the input side should be set to 2
53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter
54) Click Save to save any changes
55) Exit the tOG application and relaunch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
17wwwgrassvalleycom
MySQL Installation (cont)
56) IMPORTANT Xitami Web Server service must be stopped on the tOG server
Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server
57) Right-click Properties and under Gen-eral tab Startup type set to Disable
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
18wwwgrassvalleycom
MySQL Installation (cont)
58) Then ensure Service Status is STOPPED Click Apply and close the window
59) Next verify the Windows Firewall is turned OFF
60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing
61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process
62) Close all windows
63) Restart the tOG server
64) Launch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
15wwwgrassvalleycom
MySQL Installation (cont)
36) The GV Sports shortcut can be copied to the desktop
37) Once installation of tOG Pre tOG and GV Sports is complete restart the tOG server
38) After Windows OS starts insert the USB License Dongle into a USB port on the tOG server
39) Launch GV Sports with the desktop shortcut
35) Within this folder should be two directory folders GV Sports and tOGGVDynoClient and these Shortcuts GV Sports tOG Edit tOG Sports tOG Playout tOG Live and Uninstall
40) In the bottom left corner of the tOG GV Sports interface panel select the Clip tab
41) Under Clip Control Plugin select K2DirClipStore
42) In the Address field enter the IP address of the K2 Summit Con-trol Connection (In this example 10164170 is used)
43) In the Directory Root field either leave blank or enter a specific root folder for example Dyno (case sensitive)
44) For Input Channel 1 and 2 uncheck the box to state false for those chan-nels
45) For Input Channel 3 and 4 check the box to state true for those channels This allows for control of the K2 Sum-mit output channels
46) Set Automatic Updates to true as well so that the clip information updates when clips are created or renamed on the K2 Dyno S panel (See above pic-ture for example of correct settings)
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
16wwwgrassvalleycom
MySQL Installation (cont)
48) From the right hand panel of tabs select tOG Preferences
49) Under the Protocol tab None should be the Protocol setting
50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes
47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List
51) Under the Video tab choose the input and output device settings
52) If using the split screen tool the Number of Channels on the input side should be set to 2
53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter
54) Click Save to save any changes
55) Exit the tOG application and relaunch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
17wwwgrassvalleycom
MySQL Installation (cont)
56) IMPORTANT Xitami Web Server service must be stopped on the tOG server
Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server
57) Right-click Properties and under Gen-eral tab Startup type set to Disable
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
18wwwgrassvalleycom
MySQL Installation (cont)
58) Then ensure Service Status is STOPPED Click Apply and close the window
59) Next verify the Windows Firewall is turned OFF
60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing
61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process
62) Close all windows
63) Restart the tOG server
64) Launch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
16wwwgrassvalleycom
MySQL Installation (cont)
48) From the right hand panel of tabs select tOG Preferences
49) Under the Protocol tab None should be the Protocol setting
50) In the Video Streaming Bitrate field the values of 600060006000 are the default (These determine the minimum starting and maximum bit rates for the video maintained in the K2 Dyno GV Sports Interface) Values may be altered to a maximum setting of 100001000010000 and press the Enter key on the keyboard to accept changes
47) Press F6 to launch the Refresh Clip List window Click Refresh Clip List
51) Under the Video tab choose the input and output device settings
52) If using the split screen tool the Number of Channels on the input side should be set to 2
53) By having the Flicker Filter option checked video may appear ldquosoftrdquo If this is the case uncheck Flicker Filter
54) Click Save to save any changes
55) Exit the tOG application and relaunch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
17wwwgrassvalleycom
MySQL Installation (cont)
56) IMPORTANT Xitami Web Server service must be stopped on the tOG server
Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server
57) Right-click Properties and under Gen-eral tab Startup type set to Disable
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
18wwwgrassvalleycom
MySQL Installation (cont)
58) Then ensure Service Status is STOPPED Click Apply and close the window
59) Next verify the Windows Firewall is turned OFF
60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing
61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process
62) Close all windows
63) Restart the tOG server
64) Launch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
17wwwgrassvalleycom
MySQL Installation (cont)
56) IMPORTANT Xitami Web Server service must be stopped on the tOG server
Windows Start Control Panel Administrative Tools Services ndash locate Xitami Web Server
57) Right-click Properties and under Gen-eral tab Startup type set to Disable
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
18wwwgrassvalleycom
MySQL Installation (cont)
58) Then ensure Service Status is STOPPED Click Apply and close the window
59) Next verify the Windows Firewall is turned OFF
60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing
61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process
62) Close all windows
63) Restart the tOG server
64) Launch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
18wwwgrassvalleycom
MySQL Installation (cont)
58) Then ensure Service Status is STOPPED Click Apply and close the window
59) Next verify the Windows Firewall is turned OFF
60) Go to Windows Start and type Windows Firewall The selection needed is under the Control Panel listing
61) If needed the panel on the left ldquoTurn Windows Firewall on or offrdquo will assist in this process
62) Close all windows
63) Restart the tOG server
64) Launch with the GV Sports shortcut
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
19wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller
1) Start a replay session with the K2 Dyno S and start recording
2) Launch the tOG application on the tOG server
3) On the K2 Dyno S use either the Home screen tOG launch tab or Windows Start GV Sports The GV Sports window opens on the K2 Dyno S and reveals the interface
4) Click Show Tools in the bottom-left corner to expose the tools
6) Click Clips in the upper-right to access clips on the K2 Summit
5) Apply any of the tools to the video on the screen Split Screen may not be used at the same time with any of the ldquodrawrdquo tools
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
20wwwgrassvalleycom
Using the tOG Application on K2 Dyno S Controller (cont)
7) Double tap a clip to load it to the K2 Summit output channel
8) Use the Jog knob to locate a specific frame and apply any of the tools to the clip This adds a keyframe to the Stack catalogue viewable at the tOG server interface screen
9) Use the Restart button at the top to recue the clip and the overlay graphic clears
10) Click Replay at the top to play the clip It will add the overlay graphic at the selected keyframe
11) Pause and Animation Off points can be added to the Stack Split Screen cannot be part of the stack
12) Spot Shadow Spot Zoom and Blur follow keyframe paths Apply any of these tools and jog to the next key-frame and reposition the focus point
13) Use the Switch button top-left to switch back to the K2 Dyno S inter-face screen
14) Use the Exit button to exit the GV Sports application on K2 Dyno The tOG server will continue to operate and waits for a new K2 Dyno connec-tion via GV Sports
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
21
APPLICATION NOTE RT SOFTWARE TOG GV SPORTS AND K2 DYNO S
Appendix
1) Double click on the DVS driver installer
2) Click Next
3) Accept the EULA and click Next
4) Use the default Installation Directory loca-tion and click Next
5) The driver will now install Once completed a confirmation window opens Click Finish Then close all open windows
6) Windows Power Save Mode
If configuring a tOG server for the first time this is a reminder to change the Power Sav-ing mode (in Windows Control Panel) to NEVER
Service Help
Contact your regional Grass Valley technical service representative for support Online service support can be found at wwwgrassvalleycomsupportcustomer_care
GVB-1-0105C-EN-AN
This product may be protected by one or more patents For further information please visit wwwgrassvalleycompatents
Beldenreg Belden Sending All The Right Signalsreg the Belden logo Grass Valleyreg and the Grass Valley logo are trademarks or reg-istered trademarks of Belden Inc or its affiliated companies in the United States and other jurisdictions Grass Valley products listed above are trademarks or registered trademarks of Belden Inc GVBB Holdings SARL or Grass Valley Canada Belden Inc GVBB Holdings SARL Grass Valley Canada and other parties may also have trademark rights in other terms used herein
Copyright copy 2015 2019 Grass Valley Canada All rights reserved Specifications subject to change without notice
WWWGRASSVALLEYCOMJoin the Conversation at GrassValleyLive on Facebook Twitter YouTube and Grass Valley - A Belden Brand on LinkedIn
wwwgrassvalleycomblog
reg
top related