rt-radiographic testing of welds general incl accept cr.pdf
Post on 07-Sep-2015
79 Views
Preview:
TRANSCRIPT
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
1 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
Utfrt av/Written by Godkjent av/Approved by Issued Date Expiration Date: Rev.
Bent Arild Aspeli Ole Kr. Finnbrten 2010-06-01 2012-06-01 0
Bent Arild Aspeli Chris Neal 2012-06-01 2014-06-01 A
INNHOLD CONTENT
1 HENSIKT OG OMFANG 1 PURPOSE AND SCOPE
2 PERSONELL 2 PERSONNEL
3 ANSVAR 3 RESPONSIBILITY
4 UTSTYR 4 EQUIPMENT
5 PERIODISK KONTROLL 5 PERIODIC INSPECTION
6 UTFRELSE 6 PERFORMANCE
7 AKSEPTKRITERIE 7 ACCEPTANCE
8 RAPPORTERING 8 REPORTING
9 REFERANSER 9 REFERENCES
10 ENDRINGER 10 CHANGES
11 VEDLEGG 11 ENCLOSURE
1 HENSIKT OG OMFANG
Hensikten med denne prosedyren er
fastlegge rutiner gjeldende for radiografisk
prving.
Prosedyren omfatter metoder og krav til
personell og utstyr ved radiografisk prving av
sveis og grunnmateriale i stl (karbon- og
rustfritt stl).
1 PURPOSE AND SCOPE
The purpose of this procedure is to state
routines regarding radiographic testing
The procedure encompasses the methods,
personnel qualification requirements and
equipment utilised for the radiographic testing
of welds and base material in steel (carbon and
stainless steel).
2 PERSONELL
Personell som utfrer rntgenkontroll skal
vre kvalifisert i henhold til. NS-EN 473 /
Nordtest niv 2.
Ansvarlig person for rntgenkontrollen skal
vre kvalifisert i henhold til NS-EN 473 /
Nordtest niv 3.
2 PERSONNEL
Personnel performing radiographic testing shall
be qualified in accordance with NS-EN 473 /
Nordtest level 2.
Responsible person for all radiographic testing
shall be qualified in accordance with NS-EN
473 / Nordtest level 3.
3 ANSVAR
Det er bedriftens NDT niv 3`er som er
ansvarlig for at denne instruks blir fulgt, og
revidert.
3 RESPONSIBILITY It is the NDE level 3 of the company who is
responsible to make sure that this procedure is
followed and revised.
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
2 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
4 UTSTYR
4.1 Strlingskilder
Det skal brukes enten rntgenapparat eller en
radioaktiv isotop.
RPSVbenytter:
Rntgen:
Andrex Smart 200 kV Rettstrler
Balteau 200 kV Rettstrler
Balteau 300 kV Rundstrler
CP Scanray 150 kV Rundstrler
Isotop:
Ir 192
4 EQUIPMENT
4.1 Radiation Sources
Either X-ray or isotope sources shall be used.
RPSV use:
X-ray:
Andrex Smart 200 kV Direct beam
Balteau 200 kV Direct beam
Balteau 300 kV circumferential beam
CP Scanray 150 kV circumferential beam
Isotope:
Ir 192
4.2 Penetrametere
Trdpenetrametere i hendhold til NS-EN
462-3 skal benyttes.
4.2 Penetrameters
Wire penetrameters inn accordance to
NS-EN 462-3 shall be used
Anbefalte Penetrameter typer /
Recommended Penetrameter types
Trdtykkelse (mm)
Wire thickness (mm)
Godstykkelse (mm)
Material thickness (mm)
10 ISO 16 0,1 0,4 90
4.3 Film
Det skal brukes finkornfilm av type Agfa
Gevaert D7, Kodak AX eller tilsvarende. Film
med finere korn (langsom film) skal brukes
etter behov. Se kapittel 6.2
Det skal benyttes ferdige vakumpakket film
med 0,02mm blyfolie.
Ueksponerte filmer skal oppbevares slik at de
ikke utsettes for radioaktiv strling, lys, stv
eller hy temperatur (over 20C) over lengre
tid. Maksimal sverting p ueksponert film skal
vre 0,3.
4.3 Films
It shall be used fine-grain films only, e.g.
Agfa Gevaert D7 and Kodak AX. More fine-
grained (slower) films shall be used
whenever necessary. See chapter 6.2
It shall be used vacuum packed film with
lead foil 0.02mm thickness.
Unexposed films shall be stored in such a
way that they are protected from radiation,
light, dust or high temperatures (above 20C)
for extended periods. The maximum density
of unexposed films shall be 0.3.
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
3 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
5 PERIODISK KONTROLL
rlig (eller hvis det er utfrt omfattende
reparasjoner) :
Autorisert personell skal kontrollere /
sertifisere:
Strlemler, personmonitor, filmbetrakter,
svertningsmler og isotop utstyr komplett.
Dette skal dokumenteres
Fr bruk:
Alt utstyr for RT kontrolleres visuelt med
tanke p skader.
5 PERIODIC INSPECTION
Yearly (or if the equipment has been subjected
major repair):
Authorized personnel shall inspect / certify:
Actinometer (radiation meter), personal
radiation monitor, film projector, densitometer
and isotope equipment complete.
Before use:
All RT equipment shall be checked for
damages before use.
6 UTFRELSE
Generelt Normalt skal radiografisk teknikk klasse A
benyttes. P kundens forlangende velges
klasse B.
Rntgenkontrollen skal ikke finne sted fr 48
timer etter ferdig sveis. Holdetiden kan
reduseres til 24 timer for stltyper 355MPa
eller lavere, og stltyper 420MPa eller laver
med en materialtykkelse mindre enn 40mm.
Hvis det er pkrevd med sliping av
sveiserken eller glding, skal
rntgenkontrollen finne sted etter dette er
utfrt.
Vanligvis er overflatepreparering undvendig,
men nr uregelmessigheter i overflaten eller
overflatebeskyttelse kan gjre det vanskelig
tolke radiogrammet, br overflaten bearbeides
eller belegget fjernes. Dette skal eventuelt
gjres i samrd med oppdragsgiver.
6 PERFORMANCE
General Normally radiographic technique class A shall
be used. On customers demands class B can be
used.
Final inspection of structural steel welds
shall not be carried out before 48 hours after
completion. Time can be reduced to 24 hours
for steel grades of 355 MPa or lower, and for
steel grades 420 Mpa below 40mm plate
thickness.
If post weld heat treatment or grinding is
required, final inspection shall be carried out
after that operation.
In general preparation is not necessary, but
where surface irregularities or coatings might
cause difficulty in detecting defects, the surface
should be ground smooth or the coating
removed. This has to be carried out in
co-operation with the employer.
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
4 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
6.1 Strlingskilder
Ved valg av strlingskilde velges fortrinnsvis
rntgenapparat, og det skal som hovedregel
vre utstyrt med en spalteblende. Der hvor
forholdene gjr det vanskelig komme til med
rntgenapparat, brukes en isotop (Ir 192).
Isotoper egner seg best ved radiografi av
tykkere gods (over 20 mm). Skal tynt gods
radiograferes og det er praktiske
vanskeligheter med bruke rntgenapparat,
tillates bruk av isotop etter avtale med
kunde.
Brukes isotop skal kollimator brukes.
For opprette en god flsomhet skal
rrspenningen holdes s lav som mulig,
maksimalverdien er gitt i fig 1. Ved
tykkelsevariasjon kan rrspenningen kes
noe.
For stl < 50kV, for Titan < 40kV,
for Aluminium < 30kV I forhold til fig.1
6.1 Radiation Sources
The usual choice of radiation source shall be an
X-ray apparatus equipped with a slit diaphragm.
When access with X-ray is difficult, isotope
(Ir 192)
Gamma-rays are ideal when radiographing
thicker materials (above 20 mm). When the use
of X-rays for thin materials is unpractical,
isotope may be utilised by agreement with
client.
With the use of gamma-rays a collimator shall
be used.
To maintain good flow sensitivity, the X-ray
tube voltage should be as low as possible.
Maximum values is given in Fig. 1.
When variations in thickness a slightly higher
voltage can be used.
For steel < 50kV, for Titanium < 40kV,
for Aluminum < 30kV In accordance to
fig.1
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
5 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
Fig. 1
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
6 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
6.2 Filmtyper
Normalt benyttes film tilsvarende Agfa D7
Nr Isotop benyttes skal man benytte mer
finkornet film som Agfa D5 eller bedre.
Hvis kunden forlanger teknikk klasse B
skal Film som Agfa D5 eller bedre benyttes
6.2 Type of films
Normally film equivalent to Agfa D7 shall be
used. When Gamma-rays are used, more fine-
grained film, e.g. Agfa Gevaert D5 or better
shall be used. If Customer demand technique B
Agfa D5 or more fine grained film shall be
used.
6.3 Strleretning/avskjerming
Strlene skal treffe filmen s vinkelrett som
mulig, s sant ikke andre forhold tilsier noe
annet. Radiograferes det mot en fri ende
skal denne avskjermes for unng
spredestrling p filmen, og slik at
omgivelsene ikke utsettes for undig
bestrling. Plasseres gods som skal
radiograferes tett inntil en vegg eller nr
gulv slik at bakstrling kan oppst, skal det
skjermes ekstra med bly p baksiden av
filmen.
6.3 Beam Direction/Screening
Whenever possible the radiation beam shall
be perpendicular to the film. When a free end
of the object is examined it shall be screened
so as to protect the film and the surrounding
area from superfluous radiation. When
material is examined close to a wall or the
floor, then extra lead screens shall be used on
the back of the film in order to protect from
back scattering.
6.4 Forskjellig godstykkelse
Radiograferes et omrde med variasjon i
godstykkelsen, kompenseres dette ved
bruke to filmer med forskjellig
eksponeringshastighet. Ved store avvik tas
flere eksponeringer.
6.4 Variations in Thickness
Unequal section thickness in the material
under examination is compensated for by the
use of two films of different exposure speed.
For large thickness variations multiple
exposures shall be used.
6.5 Bakstrling
For kontrollere at det ikke har forekommet
bakstrling p filmene, festes en "B"(hyde
minst 13 mm og tykkelsen minst 1,6) av bly
p baksiden av filmen. Er denne "B" synlig
(lyst) p radiogrammet, er kvaliteten ikke
tilfredsstillende.
6.5 Back-scatter
As a check on back-scattered radiation, a lead
symbol "B" (height minimum 13 mm and
thickness minimum 1,6 mm) shall be attached
to the back of the film. If the light image of the
"B" appears on the radiograph then the
radiograph shall be considered unacceptable.
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
7 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
6.6 Bildekvalitetsindikator (IQI)
Penetrameter
Penetrameterne skal plasseres p strlesiden
p den del som skal radiograferes.
Indikatoren skal ha kontakt med
prvingsobjektets overflate. Plasseringene skal
vre slik at minst 10 mm av trdlengden er
synlig i et omrde med jevn sverting.
I de tilfeller det ikke er tilkomst for plassering
av penetrameteret p strlesiden skal det
plasseres p filmsiden, men det skal gjres
oppmerksom p det. Dette skal skje ved at
man fester en blybokstav "F" ved siden av
penetrameteret.
Ved eksponering skal indikatoren plasseres
med trdene vinkelrett p sveisen.
Radiograferes enkeltfilmer plasseres ett
penetrameter i enden av hver film, og slik at
den tynneste trden ligger ut mot enden av
filmen. Ved radiografering av rundsmmer
hvor hele smmen tas i samme eksponering,
brukes 4 penetrametere som plasseres med lik
deling rundt.
Tynneste synlig trd er den tynneste trden
som sammenhengende er synlig over en
lengde p minst 10 mm.
6.6 Image quality indicator (IQI)
Penetrameter
Whenever possible the IQI shall be placed on
the source side of the object during
examination.
The IQI shall be in close contact with the
surface of the object. Its location shall assure
that at least 10 mm of the wire length will show
in an area of uniform density.
When inaccessibility prevents this, the IQI shall
be placed on the film side adjacent to a lead
letter "F".
At exposures according the IQI shall be placed
with the wires perpendicular to the weld.
When radiographing single films one IQI shall
be used, placed at one end of each film so that
the thinner wire is towards the end. For
radiography of circumferential seams with
simultaneous exposure 4 IQI `s shall be equally
spaced along the circumference.
The image of a wire is accepted as visible if a
continuous length of at least 10 mm is clearly
visible in a region of uniform optical density.
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
8 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
6.7 Merking
Enten skal blybokstaver/tall eller lysmerking
brukes for identifikasjon av radiografier.
Merkingen skal plasseres slik at de ikke
vanskeliggjr vurderingen av radiografiet.
Flgende identifikasjonssystem skal brukes: se
Fig.2
6.7 Marking
Either lead figures or light marking shall be
used for identification of radiographs. The
marking shall be placed in such a way that
evaluation of the radiographs is not impaired.
The following identification system shall be
used: See Fig.2
Nullpunkt skal merkes p objekt. (Tusj eller
maling skal brukes.) Samme nullpunkt skal
benyttes som referanse for all ikke-destruktiv
prving. Mlbnd med blytall som angir
avstand fra nullpunktet skal eksponeres inn p
hver film. Maks. avstand mellom blytallene
skal vre 200 mm.
Blytallenes posisjon merkes p objektet fr
mlebndet fjernes. (Tusj eller maling brukes.)
Alle blytall/bokstaver skal plasseres p
objektet, og ikke p filmen.
Ved radiografi av rundsmmer hvor hele
smmen tas i en eksponering, skal kun frste
og siste film eksponeres med komplett
identifikasjon i henhold til ovennevnte. De
vrige filmer pfres ordrenr og filmnr med
tusj.
Zero point shall be marked on the object (by use
of ink or paint). The same zero-point shall be
used as reference for all non-destructive testing.
A tape measuring with lead numerals which
give distance from zero-point shall be exposed
on each film. Max. intervals between each lead
numeral shall be 200 mm.
The position of the lead numerals shall be
marked on the object prior to tape removal (by
use of paint or ink).
All lead figures shall be placed on the object
and not on the film.
For radiography of circumferential seams with
simultaneous exposure, only the first and the
last film shall be exposed with complete
identification in accordance with above. Order
no. and film no. are added to the remaining
films by use of ink.
0
O.2861
20 40
X XXX X
X XXX X
Order no. Drawing no. Weld no.
D.or T. 287876 W. or S. 28
(Film no.)
(F. 1)
Fig 2
Film
Weld
IQI Lead tape meassure
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
9 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
Ved eksponering av filmene vil blytallene p
mlebndet bekrefte rekkeflgen, samt vise
overlapp mellom filmene. Ved stikkprver
legges p mlebnd der en kan definere et
klart nullpunkt. Hvis ikke, skal filmnr
stemples inn p objektet og skisse tegnes.
Evt. radiografier etter reparasjon merkes i
tillegg med R1, R2 etc. bak ovennevnte
identifikasjon.
Hvis det er vanskelig tolke sveisens
beliggenhet eller det omrde som skal
kontrolleres pga sliping, maskinering etc. skal
blymerker benyttes (pil eller lignende.)
By film exposure the lead numerals on the tape
will confirm the ranking, and also show overlap
between the films. By spot-testing on parts
where a clear zero points can be defined a
measuring tape with lead numerals shall be
used. If this is not possible, the film no. shall be
stamped on the object and a sketch drawn.
In addition any radiographs taken after repair
shall be marked R1, R2 etc. behind the above-
mentioned identification.
If there are difficult to detect where the weld
are, or the area to be interpreted, lead marks
shall be used ( lead arrows, e.g.)
6.8 Geometrisk uskarphet
Hvis ikke kunden har spesifisert noe annet
skal den geometrisk uskarpheten ikke
overskride: 0,50 mm.
Minimumsavstand fokus-film ved
forskjellige materialtykkelser:
UG = Geometrisk uskarphet
f = avstand fokus-film i mm.
d = strrelse p fokus i mm.
b = godstykkelse i mm. (Hvis filmen ikke
ligger tett inn mot objektet, skal avstanden
mellom film og objekt legges til
godstykkelsen.)
Fokusstrrelsen p vre Rntgenapparater er:
Andrex Smart 200 kV - 1,6 x 1,6 mm.
Balteau rettstrler 200 kV - 2.5 x 2,5 mm.
Balteau rundstrler 300 kV 5mm.
CP Scanray rundstrler 150 kV - 3 x 0,3mm.
Fokusstrrelsen p vr isotop er:
Ir 192 - 2 x 2mm.
Figur 3 gir rettninglinjer for min. film - focus
avstand.
6.8 Geometrical Unsharpness
If not other specified from customer the
geometric unsharpness shall not exceed:
0,50 mm
Minimum distance focus-object by different
material thicknesses:
UG =Geometrical unsharpness:
f = distance focus-object in mm.
d = focus size in mm.
b = material thickness in mm. (If the film is
not lying close to the object, the distance
between film and object shall be added to the
material thickness.)
The source sizes of our X-ray apparatus are:
Andrex Smart 200 kV - 1,6 x 1,6 mm.
Balteau direct beam 200 kV - 2.5 x 2,5 mm.
Balteau circumf. beam 300 kV 5mm.
CP Scanray circumf. beam 150 kV - 3 x 0,3mm.
The source sizes of our isotope is:
Ir 192 - 2 x 2mm.
Fig.3 can be used as guidelines for minimum
film - focus distance.
UG = b x d
f - b UG =
b x d
f - b
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
10 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
3
3
d = source size
b = object to film distance
(Thickness)
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
11 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
6.9 Overlapp
Generelt skal det vre en minste overlapp p
20 mm filmene imellom i tillegg til den
ndvendige overlapp som den skr
gjennomgang ved radiografi av rette objekter
krever. Ved radiografi av rette objekter gr
strlene p skr igjennom godset i filmens
ytterpunkter. kningen i godsmengde som
strlen skal passere p grunn av dette m ikke
overstige 6% (se fig 4).
For beregning av overlapp brukes flgende
formel:
OL b
a
O = overlapp
L = filmens lengde
b = objekt tykkelse
a = avstand film-fokus
For vrige eksponeringsteknikker se minste
antall eksponeringer p fig. A1 og fig. A2
6.9 Overlapping
In general the minimum film overlap shall be 20
mm, in addition to necessary overlap caused by
the deflection when radiographing flat objects.
When radiographing flat objects the rays will be
deflected at the film perimeter. The resultant
increase in material thickness due to this shall
not exceed 6% (see fig.4)
The overlap shall be calculated based on the
following formula:
OL b
a
O = overlap
L = film length
b = object thickness
a = distance from film to source
For other exposure techniques, see minimum
numbers of exposures at fig. A1 and fig. A2
Fig.4 a
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
12 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
6.10 Radiografiske teknikker.
Forklaringer:
t = nominelle tykkelsen av grunnmateriale.
b = avstanden mellom prveobjektets
strleside og film mlt langs strlens
sentralakse.
f = avstand mellom strlekilden og objektet
mlt langs strlens sentralakse.
FFA = avstanden mellom strlekilden og
filmen.
De = ytre diameter
Ellipseteknikken fig. 15 skal ikke benyttes
for utvendig diameter De > 90mm, en vegg-
tykkelse t > 8mm og en sveisebredde p
De/4. To bilder som er forskjvet 90, er
tilstrekkelig hvis t/De < 0,12.
Ellipsepningen skal vre omtrent en
sveisebredde.
6.10 Radiographic techniques
Explanation:
t = the nominal thickness of the parent metal.
b = the distance between the radiation side of
the test object and the film surface measured
along the central axis of the radiation beam.
f = the distance between the radiation source
and the test object surface measured along
the central axis of the radiation beam
FFA = the distance between the radiation
source and the film.
De = external diameter.
The elliptical technique fig. 15 shall not be
used for external diameter De > 90mm, wall-
Thickness t > 8mm and weld width De/4.
Two 90 displaced images are sufficient if
t/ De < 0,12.
The elliptical gap shall be about one weld
width.
6.10.1 6.10.1
5
5
5
5
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
13 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
6
6.10.2
8 6 6.10.2
6
6
8
7
7
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
14 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
9
6.10.3 6.10.3 9
10
9
8
8
10
11) 11)
9
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
15 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
11
6.10.4
11
12
13
12
13
12 14 12 14
6.10.4
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
16 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
14
14
6.10.5 6.10.5 15 15
15
15
6.10.6 6.10.6
16
16
16
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
17 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
6.10.7 6.10.7
17
17
17 17
18
7 18
19
19
19 19
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
18 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
19 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
20 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
6.11 Fremkalling
Fremkalling av film skal skje ved bruk av
automatisk fremkallermaskin, og i henhold
til fabrikantens anvisninger. Hvis behov for
manuell fremkalling, skal filmfabrikantens
anvisning flges.
6.11 Development
All developing of films shall be performed
by use of automatic process, and in
accordance with manufacturer's
recommendations. If manual processing is
necessary, the film manufacturer's
recommendations shall be followed.
6.12 Betrakning
Radiogrammene skal kontrolleres i et rom med
dempet belysning.
Utstyr for betraktning av film
(betraktnings-lamper) skal ikke gi lys av en
slik beskaffenhet at en fr forstyrrende
reflekser, skygger eller lignende p filmen.
Utstyret skal gi tilstrekkelig lys i skjermen
slik at en ser alle aktuelle trder p
penetrameteret.
Alle filmer skal vre fri for mekaniske eller
kjemiske skader/merker som er av en slik
grad at vurdering av filmen
vanskeliggjres.
6.12 Viewing The radiographs shall be examined in a
darkened room.
Viewing facilities shall provide subdued
lighting of an intensity that will not cause
troublesome reflection shadows or glare on the
radiographs. The equipment shall provide
sufficient light to make visible all relevant
penetrameter wires.
All radiographs shall be free from
mechanical or chemical blemishes to the
extent that they can not mask or be confused
with the image of any discontinuity in the
area of interest.
6.13 Svertning
Radiogrammets sverting i omrdet som skal
vurderes skal vre ihht tabell 4. Maksimum
sverting skal settes til hva fabrikanten av
betraktningsapparatet oppgir som
maksimalt. Ved bedmming av svertningen
skal det brukes et densitometer.
6.13 Density The transmitted film density of the area of
interest shall be in accordance to table 4.
The maximum density shall be within the
limits set out by the manufacturer of the
viewing facilities. A densitometer shall be
used for judging film density.
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
21 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
6.14 Flsomhet Se tabell B1- B12 for krav til minsteverdier
for bildekvalitet.
6.14 Sensitivity
See table B1-B12 for minimum image
quality values
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
22 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
23 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
24 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
25 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
26 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
27 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
7 AKSEPTKRITERIE
Det skal komme frem p tegning, eller annet
underlag hvilke akseptkriterier som gjelder.
RT inspektr skal gjre seg kjent med
akseptkriterie fr prvingen starter.
Se vedlegg kapittel 11 .
7 ACCEPTANCE
The acceptance standard shall be written on
work drawing or other work specification.
The RT inspector shall be familiar with the
acceptance standard before inspection starts.
See enclosure chapter 11.
8 RAPPORTERING
All Rntgenkontroll p sveis som er
nummerert skal registreres i weldeye weld
summary list.
Resultatet skal ogs rapporteres p skjema
RF-825500. Se Fig.20
Ved rapportering av sveisefeil brukes flgende
forkortelser:
Aa = Runde porer
Ab = Rrformede porer
Ba = Enkelte slagginneslutninger
Bb = Slaggstriper
C = Bindefeil
D = Rotfeil
Ea = Sprekk p langs
Eb = Sprekk p tvers
F = Kantsr
G = Negativ rkehyde
H = Stor rkehyde
I = Ujevn rkehyde
8 REPORTING
All radiographic testing performed at weld with
numbers shall be registered in weldeye weld
summary list.
The result shall also be reported on form
RF-825500. See fig.20.
By reporting weld defects, the following
abbreviations shall be used:
Aa = Round pores
Ab = Tubular pores
Ba = Single slag inclusions
Bb = Slag lines
C = Lack of fusion
D = Lack of penetration
Ea = Longitudinal crack
Eb = Transverse crack
F = Undercut
G = Incompletely filled groove
H = Too much weld
I = Uneven weld
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
28 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
Fig 20
-
Rntgenkontroll av sveis generelt
Radiographic Testing of welds general
Documenttype/Document Instruksjon / Procedure Nr./No.
QI-825500 Side/Page av/of
29 29 Sign. dato /Date
B. Aspeli 2008-06-01
____________________________________________________________________________ QI-825500
Uncontrolled when printed
9 REFERANSER
Denne prosedyren er forenelig med flere
standarder. Blant andre: NS-EN 1435
ASME V article2, Norsok M-101,
Norsok M-601.
9 REFERENCES
This procedure is in accordance with several
standards. E.g.: NS-EN 1435,
ASME V article 2, Norsok M-101,
Norsok M-601.
10 ENDRINGER
Kap.4.1 Endret tekst til RPSV
Endret Fig.20
10 CHANGES
Ch.4.1 changed text to RPSV
Changed Fig.20
11 VEDLEGG 11 ENCLOSURE Akseptkriterier
V01-RT-Norsok M101
V02-RT-Norsok M601 (ASME B31.3)
V03-RT-ASME VIII appendix 4
V04-RT-ASME VIII UW 51
V05-RT-DNV Rules for certification of
lifting appliances
V06-RT-DNV-OS-C401
V07-RT-NS-EN 12517
V08-RT-ISO 5817
V09- RT-DNV-OS-C401 (2008)
Acceptance
V01-RT-Norsok M101
V02-RT-Norsok M601 (ASME B31.3)
V03-RT-ASME VIII appendix 4
V04-RT-ASME VIII UW 51
V05-RT-DNV Rules for certification of
lifting appliances.
V06-RT-DNV-OS-C401
V07-RT-NS-EN 12517
V08-RT-ISO 5817
V09- RT-DNV-OS-C401 (2008)
file://RPKJEA01/Rainpower/RP_Fabrication/PR_Fabrication_QMS/QI-825500_V01%20Norsok%20M101.docfile://RPKJEA01/Rainpower/RP_Fabrication/PR_Fabrication_QMS/QI-825500_V02%20Norsok%20M601.docfile://RPKJEA01/Rainpower/RP_Fabrication/PR_Fabrication_QMS/QI-825500_V03%20ASME%20VIII%20app.4.docfile://RPKJEA01/Rainpower/RP_Fabrication/PR_Fabrication_QMS/QI-825500_V04%20ASME%20VIII%20UW51.docfile://RPKJEA01/Rainpower/RP_Fabrication/PR_Fabrication_QMS/QI-825500_V05%20DNV%20Rules%20for%20cert.%20of%20lift.%20appl..docfile://RPKJEA01/Rainpower/RP_Fabrication/PR_Fabrication_QMS/QI-825500_V05%20DNV%20Rules%20for%20cert.%20of%20lift.%20appl..docfile://RPKJEA01/Rainpower/RP_Fabrication/PR_Fabrication_QMS/QI-825500_V06%20DNV-OS-C401.docfile://RPKJEA01/Rainpower/RP_Fabrication/PR_Fabrication_QMS/QI-825500_V07%20NS-EN%2012517.docfile://RPKJEA01/Rainpower/RP_Fabrication/PR_Fabrication_QMS/QI-825500_V08%20ISO%205817.docfile://RPKJEA01/Rainpower/RP_Fabrication/PR_Fabrication_QMS/QI-825500_V09%20DNV-OS-C401%202008.doc -
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V09 Side / Page av / of
1 1 Standard
DNV-OS-C401 (2008)
-
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V08 Side / Page av / of
1 13 Standard
ISO 5817 : 2003(E)
-
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V08 Side / Page av / of
2 13 Standard
ISO 5817 : 2003(E)
-
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V08 Side / Page av / of
3 13 Standard
ISO 5817 : 2003(E)
-
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V08 Side / Page av / of
4 13 Standard
ISO 5817 : 2003(E)
-
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V08 Side / Page av / of
5 13 Standard
ISO 5817 : 2003(E)
-
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V08 Side / Page av / of
6 13 Standard
ISO 5817 : 2003(E)
-
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V08 Side / Page av / of
7 13 Standard
ISO 5817 : 2003(E)
-
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V08 Side / Page av / of
8 13 Standard
ISO 5817 : 2003(E)
-
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V08 Side / Page av / of
9 13 Standard
ISO 5817 : 2003(E)
-
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V08 Side / Page av / of
10 13 Standard
ISO 5817 : 2003(E)
-
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V08 Side / Page av / of
11 13 Standard
ISO 5817 : 2003(E)
-
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V08 Side / Page av / of
12 13 Standard
ISO 5817 : 2003(E)
-
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V08 Side / Page av / of
13 13 Standard
ISO 5817 : 2003(E)
-
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V06 Side / Page av / of
1 1 Standard
DNV-OS-C401 (2004)
-
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V02 Side / Page av / of
1 4 Standard
Norsok M601 Rev.4 July 2004 (ASME B31.3)
The defect acceptance level shall be in accordance with ASME B.31.3 Chapter VI, Normal Fluid Service, and
Chapter IX, High Pressure Service, for pipe classes with rating above class 2500 psi.
Chapter VI
-
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V02 Side / Page av / of
2 4 Standard
Norsok M601 Rev.4 July 2004 (ASME B31.3)
-
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V02 Side / Page av / of
3 4 Standard
Norsok M601 Rev.4 July 2004 (ASME B31.3)
-
Vedlegg til RT instruks: QI-825500
Enclosure to RT procedure QI-825500
Dokument / Document
Vedlegg / Enclosure Nr. / No.
QI-825500-V02 Side / Page av / of
4 4 Standard
Norsok M601 Rev.4 July 2004 (ASME B31.3)
Chapter IX
top related