repairing | petrochemical - superlok - mako products...5612 industrial blvd. • edmond, ok 73034...
Post on 21-Jan-2021
4 Views
Preview:
TRANSCRIPT
Safety, Quality & Reliability
Competition in Safety, Quality & Reliability
Competition in Safety, Quality & Reliability
Precise
Connect
ion Every
Time
No More
Guessw
ork!
i-Fitt
ing
Integration Tube Fitting Series
OUTPERFORMSOUTPERFORMS
5612 Industrial Blvd.www.mako-products.net
Edmond, OK 73034 Phone: 405-509-2665 Fax: 866-239-1587• •
WELD END
SUIUnion
SUTI Union Tee
page 12page 23
SCI Cappage 44
SP Plug
SSWEI Socket Weld Elbow
SSWCI Socket Weld Connector
SMPWEI Male Pipe Weld Elbow
SPWCI Male Pipe Weld Connector
SSMCI SAE/MS Male Connector
SOPCI O-Seal Pipe Thread Conn.
SOSCI O-Seal Straight Thread Connector
page 44
page 43
page 43
page 42
page 42
page 37
page 36
SAA An Adapterpage 35
SAUI An Unionpage 35
SAF An Flarepage 34
page 36
SIInsertpage 45
SVPVent Protectorpage 43
SFS Ferrule Set
SBF Back Ferrule
page 45
page 45
SFF Front Ferrule
SNI Nut
page 44
page 44
SRUTI Reducing Union Tee
SMBTI Male Branch Tee
page 23
page 24
SPMBTI Positionable Male Branch Teepage 24, 25
SFBTI Female Branch Teepage 27
SFRTI Female Run Tee
page 27
SUCI Union Cross
page 28
SMA Male Adapter
SBRBulkhead Reducer
SRI Reducer
page 31
page 31
page 30
SFA Female Adapterpage 32
SRPC Reducing Port Connector
SPC Port Connector
page 33
page 32
SFTC Flange Lapped Tubes Connectorpage 34
SRUI Reducing Union
SBHUIBulkhead Union
SGMCMale Connector For Bonded Washer Seal
page 12
SBHRUI Bulkhead Reducing Unionpage 13
page 13
SMCIMale Connectorpage 14, 15
SMCI-GM Male Connector For Metal Gasket Seal
SFCI Female Connector
SGCI Gauge Connector
SMCB Bulkhead Male Connector
SFCB Bulkhead Female Connector
SUEI Union Elbow
page 16
page 13
page 15
page 16
page 21
SMEI Male Elbowpage 18, 19
SHMEI45º Male Elbow
page 19
SPHMEI45º PositionableMale Elbowpage 20
SFEI Female Elbowpage 22
SPMEIPositionable Male Elbowpage 20, 21
SPMRTI Positionable Male Run Teepage 26
SMRTI Male Run Tee
page 25
UNION TEE
CONNECTOR
ELBOWS
VENT PROTECTOR
SPARE PART
STUB TUBE CONNECTOR
AN TUBE
O-RING SEAL
INDEXINDEX Mako Products, LLC
2
PLUG & CAP
I Tube Fitting Fitting Type Fitting Size III-I Tube O.D. III-II Pipe Thread Size or Tube Size Material
: Tube Fitting
Type of Fitting
SUI Union SMCI Male Connector SUEI Union Elbow SUTI Union Tee SWC Weld connector SRI Reducer SSMC SAE/MS O-Ring Male Connector SAU AN union SP Plug
Refer to Index - Pg 2
Size of Fitting
: Tube O.D.
: Pipe Thread Size or tube size
IV Material
Fractional Tube
Metric Tube
1/16 1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1 1-1/4 1-1/2 2 1 2 3 4 5 6 8 10 12 14 16 20 24 32
O.D (Inch) Identify
Aluminum(Use dash 。。-。。)
Aluminum(Use dash “-”)
AL
Brass and Copper
(Use dash “-”)
B
Carbon Steel
S45C,A105(15),SS400(400)....
316 Stainless Steel
316,316L (36L) M40
Monel Alloy 400
825
Alloy 825
625
Alloy 625
276
Alloy C-276MATERIAL
Identify
* Products are for reference only and are subject to change on client’s request.
1/8 1/4 3/8 1/2 3/4 1 2R 4R 6R 8R 12R 16R 2N 4N 6N 8N 12N 16N 2G 4G 6G 8G 12G 16G 2U 4U 6U 8U 12U 16U
Applied SizeJIS B0203(PT), DIN2999, BSPT
ANSI B1.20.1JIS B0202(PF), ISO 228/1, BSPP
AMERICAN STANDARD UNIFIED SCREW THREAD
SIZE (INCH)ISO TAPERED
NPTISO PARALLEL
UNIFIED SCREW
. TEES are described by the size of 1 & 2 and then the branch (3). CROSSES are described by the size of 1 & 2 and then the branch (3 & 4).
Ex. 1) SMBTI - 6 - 6N (- 316) MALE BRANCH TEE 3/8" X 3/8" X 3/8" NPT Stainless steel 316
Ex. 2) SUCI - 8 UNION CROSS 1/2" X 1/2" X 1/2" X 1/2"
Example
* SMCI - 8 - 6N SS316L SUPERLOK MALE CONNECTOR , Tube O.D: 1/2", Thread: 3/8" NPT, Stainless Steel 316L
* In case of Stainless Steel, it is possible to express SS316 or 316 itself.
TEES and CROSSES
1 2
4
3
- 1 - AIII - I III - II IV II
- 1 - S U I
II III ( ) IV
I
II : : :
: :
: : :
: : .
III : III-I
III-II
:
Ordering Information
.
.
: : : : : :
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •35612 Industrial Blvd. Edmond, OK 73034
Tube Fittings have been designed and manufactured under the strictest material management, high precision machining and the bestprocess technology.
Tube Fittings provide a reliable, leak proof seal under severe conditions such astemperature cycling, vibration and pulsation. In addition, Tube Fittingscan contribute to productivity improvement because of superior machined surfaces on the inner surface of each Tube Fitting.
Tube Fittings can be assembled easily without the requirement of any special tools.Consideration of the entire system design is important to ensure safe and reliable results.
Structure of
Tube Fittings consist of four precision parts that are manufactured under the strictest quality control. These four precision parts together make up the BEST Tube Fitting in the world.
Tube Fittings secure leak free connections due to ease of assembly providing customers with confidence and appreciation of overall lower cost of installed systems.
Features of Tube Fittings
NUT
BACKFERRULE
FRONTFERRULE
BODY
.
Mako Products, LLC
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •45612 Industrial Blvd. Edmond, OK 73034
5612 Industrial Blvd. Edmond, OK 73034
Quality and Process ControlMako Products Tube Fittings and Valves are produced to unmatched quality through strict statistical process control. Stringent and consistent in process analysis regulates that tight tolerances are adhered to. The written Quality Control Manual is followed and demands persistent improvement in all areas of the Quality process where possible.
WarrantyMako Products warrants that Tube Fittings shall be free from defects in material and workmanshipfor the life of the product.
The purchaser’s solutions shall be limited to replacement and installation of any parts that fail through a defect in material or workmanship.
acknowledges that this brochure is regardedas the Warranty and does not publish a separate warranty unless there is a specific special requirement.
Installation Instruction
1. Installation under 1 inch or 25MM Tube Fittings shall be delivered to the customer completely assembled and ready forinstallation. Turning the nut to the finger tight position is the only requirement before starting the installation. Fittings should not be disassembled before installation to maintain cleanliness and prevent unwanted foreign material from entering the system.
Care in the proper selection of tubing also contributes to a safe and reliable installation.
Step 1 Insert the tubing into the Tube fitting making sure the tubing is bottomed out and is in complete contactwith the shoulder of the fitting. Also, the nut should be in the finger-tight position at this time.
Step 2Before tightening, mark the nut at the 6 o’clock position.
Step 3Hold the fitting body safely with a back-up wrench and tighten the nut 1-1/4 turns until your mark reaches the 9 o’clock position.Note: For 1/16”, 1/8” and 3/16”, 2, 3 and 4 mm tube fittings, tighten the nut 3/4 of a turn to the 3 o’clock position.
GaugeabilityOn initial installation, the Inspection Gaugeassures the installer or inspector that a fitting has been sufficiently tightened.
Position the Inspection Gauge next to the gap between the nut and the body.
If the gauge will not enter the gap, the fitting is sufficiently tightened.
If the gauge will enter the gap, additional tightening is required.
Step1
Step2
Step3
Tube Fittings
.
.
.
.
.
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •5
Technical Information
2. Installation for high pressure or severe service systems
Since tubing has different O.D. tolerances, it is important to have a common starting point to take out in dimensional variations. This is done by tightening the fitting slightly until the tubing cannot freely rotate in the fitting as it can in the finger-tight position. At this point tighten the nut 1-1/4 turns.
Safety Considerations on Installations for High Pressure Systems
1. Make sure the proper tubing wall thickness is selected in accordance with pressure ratings. (see Page 10) Tubing should have a hardness of HRB 80 or less.2. Do not assemble or disassemble fittings when the system is pressurized.
3. Re-tightening Instructions
Step 1Pic. 1 shows the fitting in the disconnected position.Insert the tubing with the pre-swaged ferrules into the fitting body making sure the front ferrule is firmly seated as shown in Pic. 2
Step 2Finger-tighten the nut and then with a wrench turn the nut to the original 9 o’clock position. At this point a slight change of resistance will be felt. Tighten the nut slightly more as the change in resistance is felt and the installation is complete as shown in Pic. 3 by tightening slightly more.
Hardness LimitationHigh Quality Stainless Steel tubing that is fully annealed; Seamless or Welded per ASTM A269, A213 or equivalent should be used with Tube fittings. The tubing must be a maximum hardness of HRB 90 or less on the Rockwell Scale, however HRB 80 is more suitable for bending and offers a greater difference in hardness to the ferrules. This difference in hardness offers more ease in assembly and better interaction between the ferrules and the tubing.
. Compatibility Tube fittings are manufactured in order to be 100% interchangeable with other Tube Fittings currently on the market. fully warranties the compatibility of with different manufactures provided the same strict manufacturing practices and tolerances are held by those manufactures. If possible only the should be used to guarantee system quality.
Pic. 1
Pic. 2
Pic. 3
.
Mako Products, LLC
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •65612 Industrial Blvd. Edmond, OK 73034
..
Gas System Application
Tube Fittings are appropriate for Gas Systems, but the implementation of certain standards mentioned below should be adhered to just as in other systems.
1. Tubing hardness must be less than that of the ferrules.2. Tubing should be free of surface imperfections, defects and round in shape. 3. Refer to Table 2 on page 10 for selection of the appropriate wall thickness. (Only shaded areas should be selected for Gas Systems)4. Tubing ends must be cut squarely and perpendicular to the center-line of the tubing. After the tubing is cut it must be deburred on both the inside and outside with a High quality fully sharpened deburring tool.5. Follow the Installation Instructions from pages 5 and 6 in the catalog.6. Do not attempt to bend the tubing after a fitting has been installed in a fixed position.7. Tubing Systems should be installed to allow for adequate expansion and contraction as well as ease of maintenance.
MATERIAL
Tube Fittings are available as standard in stainless steel, brass, and alloy material. Straight fittings are machined from cold finished bar stock and shaped bodies from forgings. Specifications for fitting materials are listed below.For special applications, contact your local distributors.
Maximum Temperature by Materials
Please refer to ASME B31.3 - 1993 concerning the detailed information about the maximum & minimum temperature of various materials.
Vacuum, Cryogenic and High Temperature Applications
Tube Fittings have been tested in Vacuum, Cryogenic and High Temperatures ensuring repeatable and reliable performance in the severest of Applications.
THREADS 1. NPT (National Pipe Thread) . Thread angle 60˚
Tapered angle 1.47°
Manufactured by the standard of ASME B 1.20.1
2. ISO 7/1 Tapered ThreadThread angle 55˚Tapered angle 1.47° Equivalent to the standard of
DIN2999, BS21(BSPT) and JIS B0203(PT).
3. ISO 228/1 Parallel ThreadThread angle 55˚ Equivalent to the standard of BS 2779 (BSPP),
JIS B0202 (PF).As the thread in accordance with ISO 228/1 cannot be
sealed perfectly, the sealing shall be done by the following method.
Use a gasket or O-Ring to seal.
400 °F
400 °F
375 °F
1000 °F
1200 °F
800 °F
204 °C
204 °C
191 °C
538 °C
649 °C
427 °C
Aluminum
Copper
Steel
SUS304
SUS316
MONEL
Bar Stock
ASTM A479ASTM A276
ASTM B164
ASTM B 166
ASTM B 574
ASTM B 16ASTM B 453
Forging
ASTM A182
ASTM B 564
ASTM B 564
ASTM B 564
ASTM B 283
Material
316 SS
Monel, Alloy 400
Inconel, Alloy 600
Hastelloy, Alloy C-276
Brass
Tube Fittings
.
.
.
.
.
...
..
.
.
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •75612 Industrial Blvd. Edmond, OK 73034
① Bonded Washer SealBe sealed by contacting the inclined surface of the hex
body of male thread to the surface of the female thread. In case of sealing, a washer composed of metal and elastic material is located at the center of tapered surface.
② Metal Gasket SealA Metal gasket (generally copper) is sealed between the body of male thread and the surface of female thread.
③ Metal Gasket SealThis is a method to insert a gasket into the flat surface of thread’s inside. The sealing shall be completed with pushing the gasket by male thread surface.
4. UNF ThreadThread angle 60 ° This is classified into UN, UNC and UNF. The standard is classified by the diameter of thread and the number of threads per inch. ASME B 1.1
Tube Standard Information Tube Selection
Suitable tubing selection is essential in performance of tubing system.When selecting tubing material, size and wall thickness, customer must consider pressure, flux (flow), temperature, environment and compatibility of system.
Consideration facts at the selection of tube1. Quality of the tube materials & manufacturing method.2. Thickness and outer diameter of tube. 3. Surface treatment of tube .4. Hardness of tube.5. Concentricity of tube.
Tube BendingTubing must have a minimum straight length before the start of any bend when inserting the tube into a Tube Fitting. Tubing where the minimum straight length is not adhered can result in leakage and jeopardize the integrity of the system. See the chart below for minimum straight lengths.
Requirements for quality Tubing Material
Tubing must be free of surface imperfections and suitable for Bending.
Pressure coefficient for tubing as it relates to temperature change.
Mako Products, LLC
. .
.
..
.
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •5612 Industrial Blvd. Edmond, OK 73034 8
.
.
.
Tube bending
L: The straight line length of tubing from the ending part of tubing to the beginning part of bending.
The Requirements for Tube Quality of the material Carbon steel tubing
ASTM A179 or equivalent. Carbon steel tubing for an oil pressure usage of high quality, annealed and seamless. Maximum hardness: HRB72. Tubing must be free from scars and shall be suitable for bending and expansion works.
Copper tubing ASTM B68, B75 or equivalent. Copper tubing of high quality, annealed and seamless.
Stainless steel tubing
ASTM A213, A269 or equivalent. Stainless steel tubing of high quality,
annealed and seamless. (316, 304, 321, etc.)
Hardness: below HRB 80. Tubing must be free from scars and shall be suitable for bending and expansion works.
Hardness: below HRB 75. Tubing must be free from scars and shall be suitable
for bending and expansion works.
A Pressure Grade Coefficient of Tubing Owing to Temperature Change
Table 1
Multiply the allowable working pressure in Table 2 by the coefficient in Table 1 in order to decide allowable pressure at high temperature. (See page 9, 10)
Tube O.D.
(inch)
L(mm)
1/8 3/16 1/4 5/16 3/8 1/2 5/8 3/4 7/8 1
12.70 18.25 19.05 20.63 22.20 23.81 30.16 31.75 33.30 38.10
˚ F20040060080010001200
˚ C93204316427538649
Copper0.800.50------------
304SS1.000.930.820.760.690.30
316SS1.000.960.850.790.760.37
Monel0.880.790.790.76------
Example
SUS316
(3/8” O.D of tube) X (0.049” wall thickness) 1200 °F 4800 psi X 0.37 = 1776 psi
The applicable operation pressure of SUS316 tubing for wall thickness, 3/8” O.D X 0.049”, is 1776 psi at 1200 °F
Material
.
..
....
..
..
..
Tube Fittings
Monel tubing ASTM B165 or equivalent. 400 alloy tubing of high quality, annealed and seamless.
..
The Recommended Straight Line Length of Tube In Tube Bending.
Tube Quality Continued ....
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •5612 Industrial Blvd. Edmond, OK 73034 9
Table 2 Stainless Steel Tubing Stainless Steel tubing which is high quality (such as 304, 316, 316L and so on), fully annealed and seamless ASTM A269, A213 or equivalent.
STAINLESS STEEL FRACTIONAL TUBE
STAINLESS STEEL METRIC TUBE
Allowable stress value between -20 °F and 100 °F (-28.9 °C ~ 37.8 °C) is 19,500 psi Safety factor is 4 (Ultimate tensile strength is 75,000 psi)
.The above data is based on the minimum wall thickness and the maximum O. D. allowed by and under the standard of ASTM A269.
The dimensions are not considered to erosion or corrosion.
Technological Data
Tube O.D.(inch)1/161/8
3/161/4
5/163/81/25/83/47/81
0.120
4700
0.109
580048004200
0.095
6000490042003600
0.083
67005200420036003100
0.065
10200 8000 6500 5100 4000 3300 2800 2400
0.049
10200 7500 5800 4800 3700 2900 2400 2000
0.035
10900 7000 5100 4000 3300 2600
0.028
850054004000
0.02012000
0.0169400
0.0148100
0.0126800
0.0105600
* Tubing working pressure (psi)
* Tubing working pressure (psi)
Tube O.D.(mm)
3 4 6 810121618202225
3.05
5200
3.00
5100
2.77
6700600054004700
2.50
68006000530048004200
2.41
66005800510046004000
2.11
720057005000440040003500
2.00
680053004700420038003300
1.65
12700 9300 7300 5900 4300 3800 3400 3000 2700
1.50
11500 8400 6500 5300 3900 3400 3000 2800 2400
1.25
14400 9400 6800 5300 4400 3200 2800 2500 2300 2000
1.001530011500 7400 5800 4200 3400 2500
0.891380010100 6500 4700 3700 3000
0.7110800 7900 5000
TUBE WALL THICKNESS (mm)
TUBE WALL THICKNESS (inch)
.
Mako Products, LLC
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •105612 Industrial Blvd. Edmond, OK 73034
Union & Connector
UNION
CONNECTOR
SUIUnion
page 12
SRUI Reducing Union
SBHRUI Bulkhead Reducing Union
SBHUIBulkhead Union
SGMCMale Connector For Bonded Washer Seal
page 12
page 13
page 13
Call for information
SMCIMale Connector
page 14, 15
SMCI-GM Male Connector For Metal Gasket Seal
SFCI Female Connector
SMCB Bulkhead Male Connector
SFCB Bulkhead Female Connector
Call for information
page 16
page 15
page 16
©
SGCIGauge Connector
page 13
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
•
Connects Fractional Tubes
SU - 1SU - 2SU - 3SUI - 4SU - 5SUI - 6SUI - 8SU - 10SUI - 12SU - 14SUI - 16SU - 20SU - 24SU - 32
1/161/83/161/45/163/81/25/83/47/8 1
1-1/41-1/2
2
1.27 2.28 3.04 4.82 6.35 7.1110.4112.7015.7418.2822.3527.6934.0445.97
5/16 7/16 7/16 1/2 9/16 5/8
13/16 15/161-1/161-3/161-3/81-3/42-1/82-3/4
5/167/161/29/165/8
11/167/81
1-1/81-1/41-1/21-7/82-1/4
3
8.6312.7013.7115.2416.2516.7622.8624.3824.3825.9031.2441.1550.0467.56
10.9215.2416.0017.7818.5419.3021.8421.8421.8421.8426.4138.8645.2162.74
17.5222.3524.1326.1628.1930.2230.9831.7533.2734.7940.3848.0053.5974.68
25.1535.5637.3340.8942.9244.9551.3052.0753.5955.1164.7792.20
107.95149.35
Part No. Tube O.D.D (inch)
dMin
Width Across FlatH (inch)h (inch)
A B I L
Part No. Tube O.D.
SUI Union
Connects Fractional Tubes
31.0036.5738.6039.3739.8742.1640.8943.1844.1945.2146.9948.5149.2752.0749.2750.8053.5953.5963.2462.73
20.6023.3624.6325.4025.9027.4326.9228.4429.4628.4429.4630.9831.7531.7531.7533.2733.2733.2739.5039.00
10.9215.2415.2416.0015.2417.7815.2417.7818.5415.2417.7819.3019.3021.8417.7819.3021.8421.8421.8421.84
15.2416.0017.7817.7818.5418.5419.3019.3019.3021.8421.8421.8421.8421.8421.8421.8421.8421.8426.4126.41
8.6312.7012.7013.7112.7015.2412.7015.2416.2512.7015.2416.7616.7622.8615.2416.7622.8624.3822.8624.38
12.713.7115.2415.2416.2516.2516.7616.7616.7622.8622.8622.8624.3824.3824.3824.3824.3824.3831.2431.24
5/167/167/161/27/169/167/169/165/87/169/1611/1611/167/89/1611/167/81
7/81-1/8
7/161/29/169/165/85/8
11/1611/1611/167/87/87/811
1-1/81-1/81-1/81-1/81-1/21-1/2
7/167/161/21/29/169/165/85/85/8
13/1613/1613/1615/1615/161-1/161-1/161-1/161-1/161-3/81-3/8
1.272.282.283.042.284.822.284.826.352.284.827.117.1110.414.827.1110.4112.7010.4115.74
1/161/81/83/161/81/41/81/45/161/81/43/83/81/21/43/81/25/81/23/4
1/83/161/41/4
5/165/163/83/83/81/21/21/25/85/83/43/43/43/411
SRU - 2 - 1SRU - 3 - 2SRUI - 4 - 2SRUI - 4 - 3SRU - 5 - 2SRUI - 5 - 4SRUI - 6 - 2SRUI - 6 - 4SRUI - 6 - 5SRUI - 8 - 2SRUI - 8 - 4SRUI - 8 - 6SRUI - 10 - 6SRUI - 10 - 8SRUI - 12 - 4SRUI - 12 - 6SRUI - 12 - 8SRUI - 12 - 10SRUI - 16 - 8SRUI - 16 - 12
Part No. dMin A A1 B B1 I L
Width Across FlatTube O.D.h (inch) H (inch) H1 (inch)D (inch) D1 (inch)
SRUI Reducing Union
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
12
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
SBHRUI Bulkhead Reducing Union
Connects Fractional Tubes
10.1611.17
12.70
11.5014.6819.44
15.2417.7817.78
33.5236.5741.91
55.1160.7066.80
26.1629.4631.75
41.1445.9749.27
12.7015.2415.24
15.2416.7622.86
7/169/169/16
9/1611/167/8
5/83/4
15/16
2.284.824.82
1/81/41/4
1/43/81/2
SBHRUI - 4 - 2SBHRUI - 6 - 4SBHRUI - 8 - 4
Part No.Tube O.D. d
MinWidth Across Flat
D (inch) D1 (inch) h (inch) H (inch) H1 (inch)
A A1 I I1 L L1 L2
PanelHole
Drill Size
PanelMax.
Thickness
SBHUI Bulkhead Union
Connects Fractional Tubes
3.0512.7012.7010.16
11.1712.7012.7016.7619.0519.05
5.16 8.33 9.9211.5013.0914.6819.4422.6225.7928.9733.73
17.2731.2432.0033.5235.8136.8341.9142.6747.4953.0857.40
31.5051.3053.5957.6560.7062.2371.1272.6478.9984.5895.75
13.4624.6325.4026.1628.4429.4631.7532.5137.3342.9245.21
23.8738.1040.3842.9245.9747.4950.8052.3258.6764.2671.37
10.9215.2416.0017.7818.5419.3021.8421.8421.8421.8426.41
8.6312.7013.7115.2416.2516.7622.8624.3824.3825.9031.24
5/167/161/29/165/8
11/167/81
1-1/81-1/41-1/2
5/161/29/165/8
11/163/4
15/161-1/161-3/161-3/81-5/8
1.27 2.28 3.04 4.82 6.35 7.1110.4112.7015.7418.2822.35
1/161/8
3/161/4
5/163/81/25/83/47/81
SBHU - 1SBHU - 2SBHU - 3SBHUI - 4SBHU - 5SBHUI - 6SBHUI - 8SBHU - 10SBHUI - 12SBHU - 14SBHUI - 16
Part No. Tube O.D.D (inch)
dMin
Width Across Flat
h (inch) H (inch)
A B I I1 L L1
PanelHole
Drill Size
PanelMax.
Thickness
Connects Fractional Tubes to ISO Parallel Thread
37.5937.5943.4338.3540.8939.1238.6141.9141.9544.4548.26
1/41/41/45/165/163/83/83/81/21/21/2
1/43/81/21/41/21/43/81/21/43/81/2
4.824.824.825.587.115.586.607.115.586.607.11
5.586.606.60
-------
7.11
3/415/161-1/16
3/41-1/16
3/415/161-1/16
7/815/161-1/16
9/169/169/165/85/8
11/1611/1611/167/87/87/8
15.2415.2415.2416.2516.2516.7616.7616.7622.8622.8622.86
17.7817.7817.7818.5418.5419.3019.3019.3021.8421.8421.84
30.2230.2236.0730.9833.5331.7531.2434.5431.8034.2938.10
13.0014.2018.8013.0018.8013.0014.2018.8013.0014.2018.80
17.0020.3024.90
- -------
SGCI - 4 - 4GSGCI - 4 - 6GSGCI - 4 - 8GSGC - 5 - 4GSGC - 5 - 8GSGCI - 6 - 4GSGCI - 6 - 6GSGCI - 6 - 8GSGCI - 8 - 4GSGCI - 8 - 6GSGCI - 8 - 8G
Part No. dMin
T(PF)
Tube O.D.D (inch) d1 A B I I1 I2 L
Width Across Flath (inch) H (inch)
SGCI Gauge Connector
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
13
5612 Industrial Blvd. Edmond, OK 73034
Connects Fractional Tubes to Female NPT Thread
SMC - 1 - 1NSMC - 1 - 2NSMC - 2 - 2NSMC - 2 - 4NSMC - 2 - 6NSMC - 2 - 8NSMC - 3 - 2NSMC - 3 - 4NSMCI - 4 - 2NSMCI - 4 - 4NSMCI - 4 - 6NSMCI - 4 - 8NSMCI - 4 - 12NSMC - 5 - 2NSMC - 5 - 4NSMC - 5 - 6NSMCI - 6 - 2NSMCI - 6 - 4NSMCI - 6 - 6NSMCI - 6 - 8NSMCI - 6 - 12NSMCI - 8 - 2NSMCI - 8 - 4NSMCI - 8 - 6NSMCI - 8 - 8NSMCI - 8 - 12NSMCI - 8 - 16NSMC - 10 - 6NSMC - 10 - 8NSMC - 10 - 12NSMCI - 12 - 8NSMCI - 12 - 12NSMCI - 12 - 16NSMC - 14 - 12NSMC - 14 - 16NSMCI - 16 - 8NSMCI - 16 - 12NSMCI - 16 - 16NSMC - 20 - 16NSMC - 20 - 20NSMC - 24 - 24NSMC - 32 - 32N
23.8326.2330.4835.5635.8142.1631.2436.3232.7637.8438.3544.7046.2234.0338.6039.1135.3039.8739.8746.2247.7538.8643.4343.4349.0250.5457.1544.1949.0250.5450.5450.5457.1550.5457.1557.4057.4062.2377.2277.2288.90
113.54
20.0022.3523.8728.9529.2135.5624.6329.7125.4030.4830.9837.3338.8626.6731.2431.7527.9432.5132.5138.8640.3828.7033.2733.2738.8640.3846.9934.0338.8640.3840.3840.3846.9940.3846.9945.2145.2150.0355.1255.1261.7276.20
10.9210.9215.2415.2415.2415.2416.0016.0017.7817.7817.7817.7817.7818.5418.5418.5419.3019.3019.3019.3019.3021.8421.8421.8421.8421.8421.8421.8421.8421.8421.8421.8421.8421.8421.8426.4126.4126.4138.8638.8645.2162.74
8.63 8.6312.7012.7012.7012.7013.7113.7115.2415.2415.2415.2415.2416.2516.2516.2516.7616.7616.7616.7616.7622.8622.8622.8622.8622.8622.8624.3824.3824.3824.3824.3824.3825.9025.9031.2431.2431.2441.1541.1550.0467.56
5/167/167/167/167/167/161/21/29/169/169/169/169/165/85/85/8
11/1611/1611/1611/1611/167/87/87/87/87/87/8111
1-1/81-1/81-1/81-1/41-1/41-1/21-1/21-1/21-7/81-7/82-1/4
3
5/167/167/169/1611/167/87/169/161/29/1611/167/8
1-1/169/169/1611/165/85/8
11/167/8
1-1/1613/1613/1613/167/8
1-1/161-3/815/1615/161-1/161-1/161-1/161-3/81-3/161-3/81-3/81-3/81-3/81-3/41-3/42-1/82-3/4
1.27 1.27 2.28 2.28 2.28 2.28 3.04 3.04 4.82 4.82 4.82 4.82 4.82 4.82 6.35 6.35 4.82 7.11 7.11 7.11 7.11 4.82 7.11 9.6510.4110.4110.41 9.6511.9312.7011.9315.7415.7415.7418.2811.9315.7422.3522.3527.6934.0445.97
1/161/81/81/43/81/21/81/41/81/43/81/23/41/81/43/81/81/43/81/23/41/81/43/81/23/41
3/81/23/41/23/41
3/41
1/23/411
1-1/41-1/2
2
1/161/161/81/81/81/8
3/163/161/41/41/41/41/4
5/165/165/163/83/83/83/83/81/21/21/21/21/21/25/85/85/83/43/43/47/87/8111
1-1/41-1/41-1/2
2
Part No. Tube O.D.D (inch)
T (NPT)
dMin
Width Across FlatH (inch)h (inch)
A B I L
SMCI Male Connector
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
14
5612 Industrial Blvd. Edmond, OK 73034
Connects Fractional Tube to Female ISO Tapered Thread
SMC - 2 - 2RSMC - 2 - 4RSMCI - 4 - 2RSMCI - 4 - 4RSMCI - 4 - 6RSMCI - 4 - 8RSMC - 5 - 2RSMC - 5 - 4RSMCI - 6 - 2RSMCI - 6 - 4RSMCI - 6 - 6RSMCI - 6 - 8RSMCI - 8 - 4RSMCI - 8 - 6RSMCI - 8 - 8RSMCI - 8 - 12RSMCI - 12 - 12RSMCI - 16 - 16R
30.4835.5632.7637.8438.3544.7034.0338.6035.3039.8739.8746.2243.4343.4349.0250.5450.5462.23
23.8728.9525.4030.4830.9837.3326.6731.2427.9432.5132.5138.8633.2733.2738.8640.3840.3850.03
15.2415.2417.7817.7817.7817.7818.5418.5419.3019.3019.3019.3021.8421.8421.8421.8421.8426.41
12.7012.7015.2415.2415.2415.2416.2516.2516.7616.7616.7616.7622.8622.8622.8622.8624.3831.24
7/167/169/169/169/169/165/85/8
11/1611/1611/1611/167/87/87/87/8
1-1/81-1/2
7/169/161/29/1611/167/89/169/165/85/8
11/167/8
13/1613/167/8
1-1/161-1/161-3/8
2.28 2.28 4.82 4.82 4.82 4.82 4.82 6.35 4.82 7.11 7.11 7.11 7.119.6510.4110.4115.7422.35
1/81/41/81/43/81/21/81/41/81/43/81/21/43/81/23/43/41
1/81/81/41/41/41/4
5/165/163/83/83/83/81/21/21/21/23/41
Part No. Tube O.D.D (inch)
T (PT)
dMin
Width Across FlatH (inch)h (inch)
A B I L
SMCI Male Connector
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change. *Some Bored-Through male connectors available upon request.
SMCB Bulkhead Male Connector
Connects Fractional Tubes to Female NPT Thread*
1/81/41/43/83/83/81/21/23/41
1/81/81/41/43/81/23/81/23/41
2.28 4.82 4.82 7.11 7.11 7.11 9.6510.4115.7422.35
1/25/85/83/43/47/8
15/1615/161-3/161-5/8
1/25/85/83/43/43/4
15/1615/161-3/161-5/8
7/169/169/1611/1611/1611/167/87/8
1-1/81-1/2
12.7015.2415.2416.7616.7616.7622.8622.8624.3831.24
39.8742.1646.7350.0350.0356.3853.0858.6766.0481.02
24.6326.1626.1629.4629.4629.4631.7531.7537.3345.21
46.4849.5354.1057.4057.4063.7563.2468.8376.2093.21
31.2433.5233.5236.8336.8336.8341.9141.9147.4957.40
8.3311.5011.5014.6814.6814.6819.4419.4425.7933.73
12.7010.1610.1611.1711.1711.1712.7012.7016.7619.05
SMCB - 2 - 2NSMCB - 4 - 2NSMCB - 4 - 4NSMCB - 6 - 4NSMCB - 6 - 6NSMCB - 6 - 8NSMCB - 8 - 6NSMCB - 8 - 8NSMCB - 12 - 12NSMCB - 16 - 16N
Part No.Tube O.D.
D (inch)
dMin
T *(NPT)
Width Across Flat
h (inch) h1 (inch) H (inch)
A I I1 L L1
PanelHole
Drill Size
PanelMax.
Thickness
* ISO Tapered Threads are available upon request
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
15
5612 Industrial Blvd. Edmond, OK 73034
* ISO Tapered Threads are available upon request
SFC - 2 - 2NSFC - 2 - 4NSFC - 3 - 2NSFCI - 4 - 2NSFCI - 4 - 4NSFCI - 4 - 6NSFCI - 4 - 8NSFC - 5 - 2NSFC - 5 - 4NSFCI - 6 - 2NSFCI - 6 - 4NSFCI - 6 - 6NSFCI - 6 - 8NSFCI - 6 - 12NSFCI - 8 - 4NSFCI - 8 - 6NSFCI - 8 - 8NSFCI - 8 - 12NSFC - 10 - 6NSFC - 10 - 8NSFCI - 12 - 8NSFCI - 12 - 12NSFC - 14 - 12NSFCI - 16 - 12NSFCI - 16 - 16N
28.7033.5229.7131.2435.8137.5942.4132.0036.8332.7637.5939.1143.9447.7540.3841.9146.7348.2641.9146.7346.7348.2649.7853.3462.23
22.0926.9223.1123.8728.4430.2235.0524.6329.4625.4030.2231.7536.5740.3830.2231.7536.5738.1031.7536.5736.5738.1039.6241.1450.03
15.2415.2416.0017.7817.7817.7817.7818.5418.5419.3019.3019.3019.3019.3021.8421.8421.8421.8421.8421.8421.8421.8421.8426.4126.41
12.7012.7013.7115.2415.2415.2415.2416.2516.2516.7616.7616.7616.7616.7622.8622.8622.8622.8624.3824.3824.3824.3825.9031.2431.24
7/167/161/29/169/169/169/165/85/8
11/1611/1611/1611/1611/167/87/87/87/811
1-1/81-1/81-1/41-1/21-1/2
9/163/49/169/163/47/8
1-1/169/163/45/83/47/8
1-1/161-5/1613/167/8
1-1/161-5/1615/161-1/161-1/161-5/161-5/161-3/81-5/8
2.28 2.28 3.04 4.82 4.82 4.82 4.82 6.35 6.35 7.11 7.11 7.11 7.11 7.1110.4110.4110.4110.4112.7012.7015.7415.7418.2822.3522.35
1/81/41/81/81/43/81/21/81/41/81/43/81/23/41/43/81/23/43/81/21/23/43/43/41
1/81/83/161/41/41/41/45/165/163/83/83/83/83/81/21/21/21/25/85/83/43/47/811
Part No. Tube O.D.D (inch)
T *(NPT)
dMin
Width Across FlatH (inch)h (inch)
A B I L
Connects Fractional Tubes to Male NPT Thread*
SFCI Female Connector
SFCB Bulkhead FemaleConnector
Connects Fractional Tubes to Male NPT Thread
1/81/41/43/81/21/23/4
1/81/81/41/43/81/23/4
2.28 4.82 4.82 7.1110.4110.4115.74
9/165/83/43/4
15/161-1/161-1/4
1/25/85/83/4
15/1615/161-3/16
7/169/169/1611/167/87/8
1-1/8
12.7015.2415.2416.7622.8622.8624.38
38.1039.6244.4547.7551.5656.3863.60
24.6326.1626.1629.4631.7531.7537.33
44.7046.9951.8155.1161.7266.5473.51
31.2433.5233.5236.8341.9141.9147.49
8.3311.5011.5014.6819.4419.4425.79
12.7010.1610.1611.1712.7012.7016.76
SFCB - 2 - 2NSFCB - 4 - 2NSFCB - 4 - 4NSFCB - 6 - 4NSFCB - 8 - 6NSFCB - 8 - 8NSFCB - 12 - 12N
Part No.Tube O.D.
D (inch)
dMin
T *(NPT)
Width Across Flat
h (inch) h1 (inch) H (inch)
A I I1 L L1
PanelHole
Drill Size
PanelMax.
Thickness
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
16
Elbow & TeeELBOWS
TEESUTI Union Tee
SRUTI Reducing Union Tee
SMBTI Male Branch Tee
SPMBTI Positionable Male Branch Tee
SMRTI Male Run Tee
SPMRTI Positionable Male Run Tee
SFBTI Female Branch Tee
SFRTI Female Run Tee
SUCI Union Cross
page 23
page 23
page 24
page 24, 25
page 25
page 26
page 27
page 27
page 28
SUEI Union Elbowpage 21
SMEI Male Elbowpage 18, 19
SHMEI45º Male Elbow
SPHMEI45º Positionable Male Elbow
SPMEIPositionable Male Elbow
SFEI Female Elbow
page 19
page 20
page 20, 21
page 22
©
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
Connects Fractional Tube to Female NPT Thread
18.8023.3618.7923.3618.7923.3626.1633.0219.8124.3826.1620.8225.4026.1633.0236.8328.1928.1933.0236.8330.2235.1036.8336.8336.8341.6541.6546.4847.7560.4570.61
24.3024.3025.4025.4026.9226.9229.7131.7528.7028.7030.4830.4830.4831.2433.2737.0836.0636.0636.0639.8738.1038.1039.8739.8739.8744.7049.0249.0266.5577.98107.19
18.0018.0018.7918.7919.5519.5522.3524.3821.3321.3323.1123.1123.1123.8725.9029.7125.9025.9025.9029.7127.9427.9429.7129.7129.7134.5436.8336.8344.4550.8069.85
15.2415.2416.0016.0017.7817.7817.7817.7818.5418.5418.5419.3019.3019.3019.3019.3021.8421.8421.8421.8421.8421.8421.8421.8421.8421.8426.4126.4138.8645.2162.74
12.7012.7013.7113.7115.2415.2415.2415.2416.2516.2516.2516.7616.7616.7616.7616.7622.8622.8622.8622.8624.3824.3824.3824.3824.3825.9031.2431.2441.1550.0467.56
7/167/161/21/29/169/169/169/165/85/85/8
11/1611/1611/1611/1611/167/87/87/87/8111
1-1/81-1/81-1/41-1/21-1/21-7/82-1/4
3
1/21/21/21/21/21/25/8
13/169/169/1611/165/85/85/8
13/161-1/1613/1613/1613/161-1/1615/1615/161-1/161-1/161-1/161-3/81-3/81-3/8
1-11/162
2-3/4
2.28 2.28 3.04 3.04 4.82 4.82 4.82 4.82 4.82 6.35 6.35 4.82 7.11 7.11 7.11 7.11 7.11 9.6510.4110.41 9.6511.9312.7011.9315.7415.7415.7422.3527.6934.0445.97
1/81/41/81/41/81/43/81/21/81/43/81/81/43/81/23/41/43/81/23/43/81/23/41/23/43/43/41
1-1/41-1/2
2
1/81/83/163/161/41/41/41/45/165/165/163/83/83/83/83/81/21/21/21/25/85/85/83/43/47/811
1-1/41-1/2
2
SME - 2 - 2NSME - 2 - 4NSME - 3 - 2NSME - 3 - 4NSMEI - 4 - 2NSMEI - 4 - 4NSMEI - 4 - 6NSMEI - 4 - 8NSME - 5 - 2NSME - 5 - 4NSME - 5 - 6NSMEI - 6 - 2NSMEI - 6 - 4NSMEI - 6 - 6NSMEI - 6 - 8NSMEI - 6 - 12NSMEI - 8 - 4NSMEI - 8 - 6NSMEI - 8 - 8NSMEI - 8 - 12NSME - 10 - 6NSME - 10 - 8NSME - 10 - 12NSMEI - 12 - 8NSMEI - 12 - 12NSME - 14 - 12NSMEI - 16 - 12NSMEI - 16 - 16NSME - 20 - 20NSME - 24 - 24NSME - 32 - 32N
Part No. dMin
T (NPT)
Tube O.D. D (inch) A B LI L1
Width Across Flath (inch) H (inch)
SMEI
Male Elbow
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
18
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
Connects Fractional Tubes to Female ISO Tapered Thread
18.7923.3626.1633.0224.3825.4026.1628.2033.02
26.9226.9229.7131.7528.7030.4831.2436.0736.07
19.5519.5522.3524.3821.3323.1123.8725.9125.91
17.7817.7817.7817.7818.5419.3019.3021.8421.84
15.2415.2415.2415.2416.2516.7616.7622.8622.86
9/169/169/169/165/8
11/1611/167/87/8
1/21/25/8
13/169/165/85/8
13/1613/16
4.82 4.82 4.82 4.82 6.35 7.11 7.11 9.6510.41
1/81/43/81/21/41/43/83/81/2
1/41/41/41/4
5/163/83/81/21/2
SMEI - 4 - 2RSMEI - 4 - 4RSMEI - 4 - 6RSMEI - 4 - 8RSME - 5 - 4RSMEI - 6 - 4RSMEI - 6 - 6RSMEI - 8 - 6RSMEI - 8 - 8R
Part No. dMin
T (PT)
Tube O.D. D (inch) A B LI L1
Width Across Flath (inch) H (inch)
Connects Fractional Tubes to Female NPT Thread*
*ISO Tapered Threads are available upon request
16.5121.0818.2822.8624.1324.1328.95
24.6324.6327.9427.9429.2132.0032.00
17.2717.2720.5720.5721.8421.8421.84
17.7817.7819.3019.3019.3021.8421.84
15.2415.2416.7616.7616.7622.8622.86
9/169/1611/1611/1611/167/87/8
1/21/25/85/8
13/1613/1613/16
4.82 4.82 4.82 7.11 7.11 9.6510.41
1/81/41/81/43/83/81/2
1/41/43/83/83/81/21/2
SHMEI - 4 - 2NSHMEI - 4 - 4NSHMEI - 6 - 2NSHMEI - 6 - 4NSHMEI - 6 - 6NSHMEI - 8 - 6NSHMEI - 8 - 8N
Part No. dMin
T *(NPT)
Tube O.D. D (inch) A B LI L1
Width Across Flat
h (inch) H (inch)
SMEI Male Elbow
SHMEI 45º Male Elbow
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
19
5612 Industrial Blvd. Edmond, OK 73034
Connects Fractional Tubes to SAE/MS Straight Thread
1/43/81/23/41
7/16-209/16-183/4-16
1-1/16-121-5/16-12
4.83 7.1110.4115.7522.35
1/25/8
13/161-1/81-3/8
9/1611/167/8
1-1/41-1/2
9/1611/167/8
1-1/81-1/2
15.2416.7622.8624.3831.24
17.7819.3021.8424.8426.42
18.2920.5721.8429.7235.31
25.6427.9432.0039.8847.50
25.6528.1932.2647.2450.55
16.5120.0725.6536.5843.94
SPHMEI - 4 - 4USPHMEI - 6 - 6USPHMEI - 8 - 8USPHMEI - 12 - 12USPHMEI - 16 - 16U
Part No. Tube O.D.D (inch)
StraightThread
T(U)d
Min A B I L L1 CWidth Across Flat
h2 (inch)h1 (inch) H (inch)
Connects Fractional Tubes to SAE/MS Straight Thread
1/41/45/163/83/81/25/83/47/81
1-1/41-1/22-1/2
7/16-209/16-181/2-209/16-183/4-163/4-167/8-14
1-1/16-123/16-12
1-5/16-121-5/8-121-7/8-122-1/2-12
4.83 4.83 5.84 7.11 7.1110.4112.7015.7518.2922.3527.6934.0445.97
1/25/89/165/8
13/1613/1615/161-1/161-3/161-3/8
1-11/162
2-3/4
9/1611/165/8
11/167/87/81
1-1/41-3/81-1/21-7/82-1/82-3/4
9/169/165/8
11/1611/167/81
1-1/81-1/41-1/21-7/82-1/4
3
15.2415.2416.2616.7616.7622.8624.3824.3825.9131.2441.1550.0467.56
17.7817.7818.5419.3019.3021.8421.8421.8421.8426.4238.8645.2162.74
21.0823.1122.8624.6427.4327.4329.4631.2433.0238.3545.7250.8069.85
28.45 30.48 30.23 32.00 34.80 37.59 39.62 41.40 43.18 50.55 67.82 77.98107.19
28.4532.2629.4632.2637.8537.8543.4348.7750.5553.5958.1760.4571.63
16.5120.0718.2920.0725.6525.6529.4636.5840.3943.9454.8662.2380.26
SPMEI - 4 - 4USPMEI - 4 - 6USPME - 5 - 5USPMEI - 6 - 6USPMEI - 6 - 8USPMEI - 8 - 8USPME - 10 - 10USPMEI - 12 - 12USPME - 14 - 14USPMEI - 16 - 16USPME - 20 - 20USPME - 24 - 24USPME - 32 - 32U
Part No. Tube O.D.D (inch)
StraightThread
T(U)d
Min A B I L L1 CWidth Across Flat
h2 (inch)h1 (inch) H (inch)
SPHMEI 45º PositionableMale Elbow
SPMEI PositonableMale Elbow
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
20
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
Connects Fractional Tubes to Female ISO Parallel Thread
1/41/43/83/81/21/21/25/83/43/411
1/81/41/43/81/43/81/21/21/23/43/41
4.06 4.83 5.84 7.11 5.84 7.8710.4111.9411.9415.7515.7519.81
1/25/85/8
13/1613/1613/1615/1615/161-1/161-1/161-3/81-3/8
9/163/43/47/83/47/8
1-1/161-1/161-1/161-3/81-3/81-3/8
9/169/1611/1611/167/87/87/81
1-1/81-1/81-1/21-5/8
15.2415.2416.7616.7622.8622.8622.8624.3824.3824.3831.2431.24
17.7817.7819.3019.3021.8421.8421.8421.8421.8421.8426.4226.42
19.5621.5923.1125.9125.9125.9127.9427.9429.7229.7236.8336.83
26.9228.9630.4833.2736.0736.0738.1038.1039.8839.8849.0249.02
26.4232.2632.2637.0835.0537.0843.4343.4345.2148.7753.3453.59
17.2722.8622.8626.4226.4222.8626.4232.0032.0041.1541.1548.51
SPMEI - 4 - 2GSPMEI - 4 - 4GSPMEI - 6 - 4GSPMEI - 6 - 6GSPMEI - 8 - 4GSPMEI - 8 - 6GSPMEI - 8 - 8GSPME - 10 - 8GSPMEI - 12 - 8GSPMEI - 12 - 12GSPMEI - 16 - 12GSPMEI - 16 - 16G
Part No. Tube O.D.D (inch)
T(PF)
dMin A B I L L1 C
Width Across Flath2 (inch)h1 (inch) H (inch)
SPMEI PositionableMale Elbow
L
I
AC
dD
T
h2
h1H
C
O-ring
L1
Connects Fractional Tubes
SUE - 1SUE - 2SUE - 3SUEI - 4SUE - 5SUEI - 6SUEI - 8SUE - 10SUEI - 12SUE - 14SUEI - 16SUE - 20SUE - 24SUE - 32
1/161/83/161/45/163/81/25/83/47/81
1-1/41-1/2
2
1.27 2.28 3.04 4.82 6.35 7.1110.4112.7015.7418.2822.3527.6934.0445.97
3/83/81/21/25/85/8
13/1615/161-1/161-3/81-3/8
1-11/162
2-3/4
5/167/161/29/165/8
11/167/81
1-1/81-1/41-1/21-7/82-1/4
3
8.6312.7013.7115.2416.2516.7622.8624.3824.3825.9031.2441.1550.0467.56
10.9215.2416.0017.7818.5419.3021.8421.8421.8421.8426.4138.8645.2162.74
14.0015.7418.5420.1022.3523.1125.9027.9429.7134.5436.8344.4550.8069.85
18.0322.3525.1427.4029.7130.4836.0638.1039.8744.7049.0266.5577.98
107.19
Part No. Tube O.D.D (inch)
dMin
Width Across FlatH (inch)h (inch)
A B I L
SUEI Union Elbow
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
21
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
• * ISO Tapered Threads are available upon request
Connects Fractional Tubes to Male NPT Thread*
19.0522.3519.0519.0522.3522.3528.4419.0522.3519.0522.3522.3528.4422.3522.3537.0022.3528.4428.4431.7531.7531.7538.10
24.6327.4325.4026.9229.7131.7534.5428.7030.4830.4831.2433.2736.0636.0636.0638.8638.1039.8739.8744.7044.7049.0253.59
18.0320.8218.7919.5522.3524.3827.1721.3323.1123.1123.8725.9028.7025.9025.9028.7027.9429.7129.7134.5434.5436.8341.40
15.2415.2416.0017.7817.7817.7817.7818.5418.5419.3019.3019.3019.3021.8421.8421.8421.8421.8421.8421.8421.8426.4126.41
12.7012.7013.7115.2415.2415.2415.2416.2516.2516.7616.7616.7616.7622.8622.8622.8624.3824.3824.3824.3825.9031.2431.24
7/167/161/29/169/169/169/165/85/8
11/1611/1611/1611/167/87/87/811
1-1/81-1/81-1/41-1/21-1/2
1/211/161/21/2
11/1613/16
19/1611/165/8
11/1613/16
113/1613/16
115/161-1/161-1/161-3/81-3/81-3/8
1-11/16
2.28 2.28 3.04 4.82 4.82 4.82 4.82 6.35 6.35 7.11 7.11 7.11 7.1110.4110.4110.4112.7012.7015.7415.7418.2822.3522.35
1/81/41/81/81/43/81/21/81/41/81/43/81/21/43/81/23/81/21/23/43/43/41
1/81/8
3/161/41/41/41/4
5/165/163/83/83/83/81/21/21/25/85/83/43/47/811
SFE - 2 - 2NSFE - 2 - 4NSFE - 3 - 2NSFEI - 4 - 2NSFEI - 4 - 4NSFEI - 4 - 6NSFEI - 4 - 8NSFE - 5 - 2NSFE - 5 - 4NSFEI - 6 - 2NSFEI - 6 - 4NSFEI - 6 - 6NSFEI - 6 - 8NSFEI - 8 - 4NSFEI - 8 - 6NSFEI - 8 - 8NSFE - 10 - 6NSFE - 10 - 8NSFEI - 12 - 8NSFEI - 12 - 12NSFE - 14 - 12NSFEI - 16 - 12NSFEI - 16 - 16N
Part No. dMin
T *(NPT)
Tube O.D. D (inch) A B LI L1
Width Across Flath (inch) H (inch)
SFEI Female Elbow
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
22
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
Connects Fractional Tubes
SUT - 1SUT - 2SUT - 3SUTI - 4SUT - 5SUTI - 6SUTI - 8SUT - 10SUTI - 12SUT - 14SUTI - 16SUT - 20SUT - 24SUT - 32
1/161/8
3/161/4
5/163/81/25/83/47/81
1-1/41-1/2
2
1.272.283.044.826.357.1110.4112.7015.7418.2822.3527.6934.0445.97
3/83/81/21/25/85/8
13/161
1-1/161-3/81-3/8
1-11/162
2-3/4
5/167/161/29/165/8
11/167/81
1-1/81-1/41-1/21-7/82-1/4
3
8.6312.7013.7115.2416.2516.7622.8624.3824.3825.9031.2441.1550.0467.56
10.9215.2416.0017.7818.5419.3021.8421.8421.8421.8426.4138.8645.2162.74
14.0015.8018.5420.1022.3523.1125.9028.7029.7134.5436.8344.4550.8069.85
18.0322.3525.1427.4029.7130.4836.0638.8639.8744.7049.0266.5577.98
107.19
Part No. Tube O.D.D (inch)
dMin
Width Across FlatH (inch)h (inch)
A B I L
SUTI Union Tee
Connects Fractional Tubes
1/41/43/83/83/81/23/81/23/4
4.82 4.82 7.11 7.11 7.1110.41 7.11 10.4115.74
5/813/1613/16
11 1/161 1/161 3/81 3/81 3/8
11/167/87/81
1 1/81 1/8 1 1/21 1/21 1/2
9/169/1611/1611/1611/167/8
1 1/167/8
1 1/8
16.7622.8622.8624.3824.3824.3831.2431.2431.24
15.2415.2416.7616.7616.7622.8616.7621.8424.38
19.3021.8421.8421.8421.8421.8426.4126.4126.41
17.7817.7819.3019.3019.3021.8419.3022.8621.84
46.2251.8151.8157.4059.4359.4373.6673.6673.66
23.1125.9025.9028.7029.7129.7136.8336.8336.83
21.5924.3825.9028.7029.7129.7134.5434.5434.54
60.9672.1372.1377.7279.7579.7598.0498.0498.04
30.4836.0636.0638.8639.8739.8749.0249.0249.02
28.9531.7533.2736.0637.0839.8741.9144.7044.70
3/81/21/25/83/43/4111
SRUTI - 6 - 4SRUTI - 8 - 4SRUTI - 8 - 6SRUTI - 10 - 6SRUTI - 12 - 6SRUTI - 12 - 8SRUTI - 16 - 6SRUTI - 16 - 8SRUTI - 16 - 12
Part No.Tube O.D. d
MinWidth Across Flat
D (inch) D1 (inch) h (inch) H (inch) H1 (inch)
A A1 B B1 I I1 I2 L L1 L2
SRUTI Reducing Union Tee
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
23
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
Connects Fractional Tubes to Female NPT Thread*
18.9023.3618.7918.7923.3620.8225.4028.1928.1933.0235.8136.83
24.9124.6325.4026.9226.9229.7130.4830.4836.0636.0638.8639.87
18.3018.0317.7819.5519.5522.3523.1123.1025.9025.9028.7029.71
15.2415.2416.0017.7817.7818.5419.3019.3021.8421.8421.8421.84
12.7012.7013.7115.2415.2416.2516.7616.7622.8622.8624.3824.38
7/167/161/29/169/165/8
11/1611/167/87/81
1-1/8
1/21/21/21/21/25/85/85/8
13/1613/16
11-1/16
2.28 2.28 3.04 4.82 4.82 4.82 7.11 7.11 9.6510.4111.9315.74
1/81/41/81/81/41/81/43/83/81/21/23/4
1/81/83/161/41/45/163/83/81/21/25/83/4
SMBT - 2 - 2NSMBT - 2 - 4NSMBT - 3 - 2NSMBTI - 4 - 2NSMBTI - 4 - 4NSMBT - 5 - 2NSMBTI - 6 - 4NSMBTI - 6 - 6NSMBTI - 8 - 6NSMBTI - 8 - 8NSMBTI - 10 - 8NSMBTI - 12 - 12N
Part No. dMin
T *(NPT)
Tube O.D. D (inch) A B LI L1
Width Across Flath (inch) H (inch)
* ISO Tapered Threads are available upon request
SMBTI Male Branch Tee
Connects Fractional Tubes to Female ISO Parallel Thread
1/41/43/83/81/25/83/43/41
1/81/41/43/81/21/21/23/41
4.06 4.83 5.08 7.8710.4111.9411.9415.7519.81
1/25/85/8
13/1615/1615/161-1/161-1/161-3/8
9/163/43/47/8
1-1/161-1/161-1/161-3/81-5/8
9/169/1611/167/87/81
1-1/81-1/81-1/2
15.2415.2415.2422.8622.8624.3824.3824.3831.24
17.7817.7819.3021.8421.8421.8421.8421.8426.42
19.5621.5923.1125.9127.9427.9429.7229.7236.83
26.9228.9630.4836.0738.1038.1039.8839.8849.02
26.4232.2632.2637.0843.4343.4345.2148.7753.59
17.2722.8622.8626.4232.0032.0032.0041.1548.51
SPMBTI - 4 - 2GSPMBTI - 4 - 4GSPMBTI - 6 - 4GSPMBTI - 8 - 6GSPMBTI - 8 - 8GSPMBT - 10 - 8GSPMBTI - 12 - 8GSPMBTI - 12 - 12GSPMBTI - 16 - 16G
Part No. Tube O.D.D (inch)
T(PF)
dMin A B I L L1 C
Width Across Flath2 (inch)h1 (inch) H (inch)
SPMBTIPositionableMale Branch Tee
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
24
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
Connects Fractional Tubes to SAE/MS Straight Thread Boss
1/43/81/23/41
1-1/41-1/2
2
7/16-209/16-183/4-16
1-1/16-121-5/16-121-5/8-121-7/8-122-1/2-12
4.83 7.1110.4115.7522.3527.6934.0445.97
1/25/8
13/161-1/161-3/8
1-11/162
2-3/4
9/1611/167/8
1-1/41-1/21-7/82-1/82-3/4
9/1611/167/8
1-1/81-1/21-7/82-1/4
3
15.2416.7622.8624.3831.2441.1550.0467.56
17.7819.3021.8421.8426.4238.8645.2162.74
21.0824.6427.4331.2438.3545.7250.8069.85
28.45 32.00 37.59 41.40 50.55 67.82 77.98107.19
28.4532.2637.8548.7753.5958.1760.4571.63
16.5120.0725.6536.5843.9454.8662.2380.26
SPMBTI - 4 - 4USPMBTI - 6 - 6USPMBTI - 8 - 8USPMBTI - 12 - 12USPMBTI - 16 - 16USPMBT - 20 - 20USPMBT - 24 - 24USPMBT - 32 - 32U
Part No. Tube O.D.D (inch)
dMin A B I L L1 C
Width Across Flath2 (inch)h1 (inch) H (inch)
SPMBTIPositionableMale Branch Tee
StraightThread
T(U)
Connects Fractional Tubes to Female NPT Thread*
18.9023.3618.7918.7923.3620.8225.4028.1928.1933.0235.8136.83
24.9124.6325.4026.9226.9229.7130.4830.4836.0636.0638.8639.87
18.3018.0317.7819.5519.5522.3523.1123.1025.9025.9028.7029.71
15.2415.2416.0017.7817.7818.5419.3019.3021.8421.8421.8421.84
12.7012.7013.7115.2415.2416.2516.7616.7622.8622.8624.3824.38
7/167/161/29/169/165/8
11/1611/167/87/81
1-1/8
1/21/21/21/21/25/85/85/8
13/1613/16
11-1/16
2.282.283.044.824.824.827.117.119.6510.4111.9315.74
1/81/41/81/81/41/81/43/83/81/21/23/4
1/81/83/161/41/45/163/83/81/21/25/83/4
SMRT - 2 - 2NSMRT - 2 - 4NSMRT - 3 - 2NSMRTI - 4 - 2NSMRTI - 4 - 4NSMRT - 5 - 2NSMRTI - 6 - 4NSMRTI - 6 - 6NSMRTI - 8 - 6NSMRTI - 8 - 8NSMRT - 10 - 8NSMRTI - 12 - 12N
Part No. dMin
T *(NPT)
Tube O.D. D (inch)
A B LI L1Width Across Flat
h (inch) H (inch)
* ISO Tapered Threads are available upon request
SMRTI Male Run Tee
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
25
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
SPMRTIPositionableMale Run Tee
Connects Fractional Tubes to Female ISO Parallel Thread
1/41/43/81/23/85/83/43/41
1/81/41/43/81/21/21/23/41
4.06 4.835.84 7.8710.4111.9411.9415.7519.81
1/25/85/8
13/1615/1615/161-1/161-1/161-3/8
9/163/43/47/8
1-1/161-1/161-1/161-3/81-5/8
9/169/1611/167/87/81
1-1/81-1/81-1/2
15.2415.2416.7622.8622.8624.3824.3824.3831.24
17.7817.7819.3021.8421.8421.8421.8421.8426.42
19.5621.5923.1125.9127.9427.9429.7229.7236.83
26.9228.9630.4836.0738.1038.1039.8839.8849.02
26.4232.2632.2637.0843.4343.4345.2148.7753.59
17.2722.8622.8626.4232.0032.0032.0041.1548.51
SPMRTI - 4 - 2GSPMRTI - 4 - 4GSPMRTI - 6 - 4GSPMRTI - 8 - 6GSPMRTI - 8 - 8GSPMRT - 10 - 8GSPMRTI - 12 - 8GSPMRTI - 12 - 12GSPMRTI - 16 - 16G
Part No. Tube O.D.D (inch)
T(PF)
dMin A B I L L1 C
Width Across Flath2 (inch)h1 (inch) H (inch)
SPMRTIPositionableMale Run Tee
Connects Fractional Tubes to SAE/MS Straight Thread
1/43/81/23/41
1-1/41-1/2
2
7/16-209/16-183/4-16
1-1/16-121-5/16-121-5/8-121-7/8-122-1/2-12
4.83 7.1110.4115.7522.3527.6934.0445.97
1/25/8
13/161-1/161-3/8
1-11/162
2-3/4
9/1611/167/8
1-1/41-1/21-7/82-1/82-3/4
9/1611/167/8
1-1/81-1/21-7/82-1/4
3
15.2416.7622.8624.3831.2441.1550.0467.56
17.7819.3021.8421.8426.4238.8645.2162.74
21.0824.6427.4331.2438.3545.7250.8069.85
28.45 32.00 37.59 41.40 50.55 67.82 77.98107.19
28.4532.2637.8548.7753.5958.1760.4571.63
16.5120.0725.6536.5843.9454.8662.2380.26
SPMRTI - 4 - 4USPMRTI - 6 - 6USPMRTI - 8 - 8USPMRTI - 12 - 12USPMRTI - 16 - 16USPMRT - 20 - 20USPMRT - 24 - 24USPMRT - 32 - 32U
Part No. Tube O.D.D (inch) A B I L L1 C
Width Across Flath2 (inch)h1 (inch) H (inch)
StraightThread
T(U)d
Min
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
26
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
Connects Fractional Tubes to Male NPT Thread*
19.0519.0522.3522.3522.3528.4522.3522.3528.4428.4431.7531.7538.10
24.6326.9229.7131.2433.2736.0736.0636.0638.8638.8644.7049.0253.59
18.0319.5522.3523.8725.9028.7025.9025.9028.7028.7034.5436.8341.40
15.2417.7817.7819.3019.3019.3021.8421.8421.8421.8421.8426.4126.41
12.7015.2415.2416.7616.7616.7622.8622.8622.8624.3824.3831.2431.24
7/169/169/1611/1611/1611/167/87/87/81
1-1/81-1/21-1/2
1/21/2
11/1611/1613/16
113/1613/16
11
1-3/81-3/8
1-11/16
2.28 4.82 4.82 7.11 7.11 7.1110.4110.4110.4112.7015.7422.3522.35
1/81/81/41/43/81/21/43/81/21/23/43/41
1/81/41/43/83/83/81/21/21/25/83/411
SFBT - 2 - 2NSFBTI - 4 - 2N SFBTI - 4 - 4NSFBTI - 6 - 4NSFBTI - 6 - 6NSFBTI - 6 - 8NSFBTI - 8 - 4NSFBTI - 8 - 6N SFBTI - 8 - 8NSFBT - 10 - 8NSFBTI - 12 - 12NSFBTI - 16 - 12NSFBTI - 16 - 16N
Part No. dMin
T *(NPT)
Tube O.D. D (inch) A B LI L1
Width Across Flath (inch) H (inch)
SFBTI Female Branch Tee
Connects Fractional Tubes to Male NPT Thread*
19.0519.0522.3522.3522.3528.4431.7531.7538.10
24.6326.9229.7131.2436.0639.8744.7049.0253.59
18.0319.5522.3523.8725.9028.7034.5436.8341.40
15.2417.7817.7819.3021.8421.8421.8426.4126.41
12.7015.2415.2416.7622.8622.8624.3831.2431.24
7/169/169/1611/167/87/8
1-1/81-1/21-1/2
1/21/2
11/1611/1613/16
11-3/81-3/8
1-11/16
2.28 4.82 4.82 7.1110.4110.4115.7422.3522.35
1/81/81/41/43/81/23/43/41
1/81/41/43/81/21/23/411
SFRT - 2 - 2NSFRTI - 4 - 2NSFRTI - 4 - 4NSFRTI - 6 - 4N SFRTI - 8 - 6NSFRTI - 8 - 8NSFRTI - 12 - 12NSFRTI - 16 - 12NSFRTI - 16 - 16N
Part No. dMin
T *(NPT)
Tube O.D. D (inch) A B LI L1
Width Across Flath (inch) H (inch)
* ISO Tapered Threads are available upon request
SFRTI Female Run Tee
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
27
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
Connects Fractional Tubes
SUC - 1SUC - 2SUC - 3SUCI - 4SUC - 5SUCI - 6SUCI - 8SUC - 10SUCI - 12SUC - 14SUCI - 16
1/161/83/161/45/163/81/25/83/47/81
1.27 2.28 3.04 4.82 6.35 7.1110.4112.7015.7418.2822.35
3/83/81/21/25/85/8
13/1615/16
11-3/81-3/8
5/167/161/29/165/8
11/167/81
1-1/81-1/41-1/2
8.6312.7013.7115.2416.2516.7622.8624.3824.3825.9031.24
10.9215.2416.0017.7818.5419.3021.8421.8421.8421.8426.41
14.0015.7418.5419.5522.3523.1125.9028.7029.7134.5436.83
18.0322.3525.1426.9229.7130.4836.0638.8039.8744.7049.02
Part No. Tube O.D.D (inch)
dMin
Width Across FlatH (inch)h (inch)
A B I L
SUCI Union Cross
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
28
Stub Tube Connector, AN Tube & O-Ring Seal
STUB TUBE CONNECTOR
AN TUBE
SOSCI O-Seal Straight Thread Connector
O-RING SEAL
page 36
SOPCI O-Seal Pipe Thread Connectorpage 36
SSMCI SAE/MS Male Connectorpage 37
SRI Reducer
page 30
SBHR Bulkhead Reducerpage 31
SMA Male Adapter
page 31
SFA Female Adapter
page 32
SPC Port Connector
SRPC Reducing Port Connector
page 32
page 33
SFTC Flange Lapped Tubes Connectorpage 34
SAF An Flare
page 34
SAUI An Union
page 35
SAA An Adapter
page 35
©
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
Connects Fractional Tubes to Fractional Port
* Fractional Tube to Metric port are available upon request
SR - 2 - 1SR - 2 - 2SR - 2 - 3SR - 2 - 4SR - 2 - 6SR - 2 - 8SR - 3 - 2SR - 3 - 4SRI - 4 - 2SRI - 4 - 3SRI - 4 - 4SRI - 4 - 5SRI - 4 - 6SRI - 4 - 8SRI - 4 - 10SRI - 4 - 12SR - 5 - 6SR - 5 - 8SRI - 6 - 4SRI - 6 - 6SRI - 6 - 8SRI - 6 - 10SRI - 6 - 12SRI - 8 - 4SRI - 8 - 6SRI - 8 - 8SRI - 8 - 10SRI - 8 - 12SRI - 8 - 16SR - 10 - 12SR - 10 - 14SR - 10 - 16SRI - 12 - 8SRI - 12 - 16
28.9533.5234.2936.0637.5944.1934.7937.0836.8337.5939.1139.8740.6446.2248.0047.7541.9147.4941.4043.1848.5150.2950.2944.9546.7352.3253.8453.8460.1954.6156.1360.9654.6162.48
22.3526.9227.6829.4630.9837.5928.1930.4829.4630.2231.7532.5133.2738.8640.6441.4034.5440.1334.0335.8141.1442.9242.9234.7936.5742.1643.6843.6850.0344.4545.9750.8044.4552.32
15.2415.2415.2415.2415.2415.2416.0016.0017.7817.7817.7817.7817.7817.7817.7817.7818.5418.5419.3019.3019.3019.3019.3021.8421.8421.8421.8421.8421.8421.8421.8421.8421.8421.84
12.7012.7012.7012.7012.7012.7013.7113.7115.2415.2415.2415.2415.2415.2415.2415.2416.2516.2516.7616.7616.7616.7616.7622.8622.8622.8622.8622.8622.8624.3824.3824.3824.3824.38
7/167/167/167/167/167/161/21/29/169/169/169/169/169/169/169/165/85/8
11/1611/1611/1611/1611/167/87/87/87/87/87/8111
1-1/81-1/8
7/167/167/167/167/169/167/167/161/21/21/21/21/29/1611/1613/169/169/165/85/85/8
11/1613/1613/1613/1613/1613/1613/161-1/1615/1615/161-1/161-1/161-1/16
2.28 2.28 2.28 2.28 2.28 2.28 3.04 3.04 4.83 4.83 4.83 4.83 4.83 4.83 4.83 4.83 6.35 6.35 7.11 7.11 7.11 7.11 7.1110.4110.4110.4110.4110.4110.4112.7012.7012.7015.7415.74
1/161/83/161/161/161/21/81/41/83/161/45/163/81/25/83/43/81/21/43/81/25/83/41/43/81/25/83/41
3/47/81
1/21
1/81/81/81/81/81/8
3/163/161/41/41/41/41/41/41/41/4
5/165/163/83/83/83/83/81/21/21/21/21/21/25/85/85/83/43/4
Part No.Tube O.D. d
Min0.82.13.04.46.99.42.14.42.13.04.45.66.99.412.014.86.99.44.46.99.412.014.84.46.99.412.014.820.414.817.020.49.420.4
d1Min
Width Across FlatH (inch)h (inch)D1 (inch)D (inch) A B I L
SRI Reducer
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
30
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
SBHR Bulkhead Reducer
Connects Fractional Tubes to Fractional Port
1/81/43/81/25/81
2.14.46.99.412.020.4
1/25/83/4
15/161-1/161-5/8
7/169/1611/167/81
1-1/2
12.7015.2416.7622.8624.3831.24
42.9248.5153.8462.7365.0288.13
24.6326.1629.4631.7532.5145.21
13.4615.7417.5223.1124.7031.70
49.5355.8861.2172.8975.18100.33
31.2433.5236.8341.9142.6757.40
8.3311.5014.6819.4422.6233.73
12.7010.1611.1712.7012.7019.05
SRB - 2 - 2SRB - 4 - 4SRB - 6 - 6SRB - 8 - 8SRB - 10 - 10SRB - 16 - 16
Part No. dMin
Tube O.D.
D (inch)
Width Across Flat
h (inch) H (inch)A I I2I1 L L1
PanelHole
Drill Size
PanelMax.
Thickness
Connects Fractional Port to Female NPT Thread*
SMA - 2 - 2NSMA - 2 - 4NSMA - 3 - 2NSMA - 3 - 4NSMA - 4 - 2NSMA - 4 - 4NSMA - 4 - 6NSMA - 4 - 8NSMA - 5 - 2NSMA - 5 - 4NSMA - 6 - 2NSMA - 6 - 4NSMA - 6 - 6NSMA - 6 - 8N SMA - 8 - 4NSMA - 8 - 6NSMA - 8 - 8NSMA - 10 - 6NSMA - 10 - 8NSMA - 10 - 12NSMA - 12 - 8NSMA - 12 - 12NSMA - 12 - 16NSMA - 14 - 12NSMA - 16 - 12NSMA - 16 - 16N
29.5034.8030.2235.5631.8037.0837.8443.4332.7638.1033.5038.9039.6045.2044.5045.2050.8047.4052.3052.3052.3052.3057.9154.3058.7066.00
13.4513.4514.2014.2015.7515.7515.7515.7516.8016.8017.5017.5017.5017.5023.2023.2023.2024.7024.7024.7024.7024.7024.7026.7031.7031.70
7/169/167/169/167/169/1611/167/87/169/167/169/1611/167/89/1611/167/8
11/167/8
1-1/167/8
1-1/161-3/81-1/161-1/161-3/8
2.10 2.10 3.04 3.04 4.40 4.40 4.40 4.40 5.60 5.60 6.90 6.90 6.90 6.90 9.40 9.40 9.4012.0012.0012.0014.8014.8014.8017.2720.4020.40
4.82 7.11 4.82 7.11 4.40 4.40 4.40 4.40 4.82 6.35 4.82 6.90 6.90 6.90 7.11 9.40 9.40 9.9012.0014.9811.9414.8020.3214.9815.7420.40
1/81/41/81/41/81/43/81/21/81/41/81/43/81/21/43/81/23/81/23/41/23/41
3/43/41
1/81/83/163/161/41/41/41/45/165/163/83/83/83/81/21/21/25/85/85/83/43/43/47/811
Tube O.D.D (inch)
T*(NPT)
d( Min) d1
Width Across Flath (inch) I LPart No.
* ISO Tapered Threads are available upon request
SMA Male Adapter
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
31
5612 Industrial Blvd. Edmond, OK 73034
SFA Female Adapter
L
B
Ih
T
dD
Connects Fractional Port to Male NPT Thread*
SFA - 2 - 2NSFA - 2 - 4NSFA - 3 - 2NSFA - 3 - 4NSFA - 4 - 2NSFA - 4 - 4NSFA - 4 - 6NSFA - 4 - 8NSFA - 5 - 2NSFA - 5 - 4NSFA - 6 - 2NSFA - 6 - 4NSFA - 6 - 6NSFA - 6 - 8NSFA - 8 - 4NSFA - 8 - 6NSFA - 8 - 8NSFA - 10 - 6NSFA - 10 - 8NSFA - 12 - 8NSFA - 12 - 12NSFA - 12 - 16NSFA - 14 - 12NSFA - 16 - 12NSFA - 16 - 16N
31.5035.3032.0035.8133.0237.1039.3745.5034.2937.5934.2938.1040.3846.7343.4345.4651.8048.2653.0852.8354.8658.4257.1560.7064.26
13.4513.4514.2014.2015.7515.7515.7515.7516.8016.8017.5017.5017.5017.5023.2023.2023.2024.7024.7024.7024.7024.7026.7031.7031.70
9/163/49/163/49/163/47/8
1-1/169/163/49/163/47/8
1-1/163/47/8
1-1/167/8
1-1/161-1/161-5/161-5/81-5/161-5/161-5/8
2.10 2.10 3.04 3.04 4.40 4.40 4.40 4.40 5.60 5.60 6.90 6.90 6.90 6.90 9.40 9.40 9.4012.0012.0014.8014.8014.8017.2720.4020.40
1/81/41/81/41/81/43/81/21/81/41/81/43/81/21/43/81/23/81/21/23/41
3/43/41
1/81/83/163/161/41/41/41/45/165/163/83/83/83/81/21/21/25/85/83/43/43/47/811
Tube O.D.D (inch)
T*(NPT)
d( Min)
Width Across Flath (inch) I LPart No.
* ISO Tapered Threads are available upon request
Connects Fractional Ports
SPC - 2SPC - 4SPC - 5SPC - 6SPC - 8SPC - 12SPC - 16
22.3524.6325.9026.1635.8137.3348.00
15.7518.7920.0620.3225.9027.6834.54
6.09 9.3910.9212.7015.7422.0928.44
2.1 4.4 5.6 6.9 9.414.820.4
1/81/45/163/81/23/41
Tube O.D.(D) (inch) d (Min) IE LPart No.
SPC Port Connector
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
32
5612 Industrial Blvd. Edmond, OK 73034
.
Remove nut and ferrules from the first of two ports to be connected.
Slip nut (no ferrules) over machined ferrule end of port connector.
Insert port connector into port 1 and snug by hand. Tighten with wrench 1/4 turn only. For 1/8, 3/16 in., 2, 3, and 4mm tube fittings, tighten only 1/8 turn. Subsequent connections are made by tightening slightly with a wrench after snugging the nut by hand.
Insert other end of port connector into port 2 and tighten nut 1 1/4 turns from finger-tight. For 1/16, 1/8, 3/16 in., 2, 3, and 4mm tube fittings, only 3/4 turn from finger-tight is necessary.
SRPCReducing Port Connector
Connects Fractional Port to Male AN
SRPC - 2 - 1SRPC - 4 - 1SRPC - 4 - 2SRPC - 6 - 2SRPC - 6 - 4SRPC - 8 - 4SRPC - 8 - 6SRPC - 12 - 8SRPC - 16 - 8SRPC - 16 - 12
1/161/161/81/81/41/43/81/21/23/4
1/81/41/43/83/81/21/23/411
0.76 0.76 2.10 2.10 4.40 4.40 6.90 9.40 9.4014.80
6.09 9.39 9.3912.7012.7015.7415.7422.0928.4428.44
8.63 8.6313.4613.4615.7415.7417.5224.3824.3825.90
2.033.553.303.813.303.813.303.814.824.06
17.2718.0322.6023.1124.8929.2130.4837.8442.6743.43
Part No.Tube O.D.
D1 (inch)
Reduced Tube O.D.
D (inch)d E I I1 L
Installation InstructionsPort Connector
machined ferrule end
Port 1 Port 2
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
. .
.
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
33
5612 Industrial Blvd. Edmond, OK 73034
SFTC Lap Joint FlangeTubes Connector
SAF An Flare
Connects Fractional Tubes
Flange Seal Finish
Lap joint flange tube connector provides easy joint between process lines and instruments designed for use with 1/2in Lap joint flanges to ANSI B 16.5 or BS 1560
SmoothIdentifier : SMRa 3.2 ~ 6.3 micrometer
SerratedIdentifier : SRRa 6.3 ~ 12.5 micrometer
Two surface finishes, smoothor serrated, are available on the sealing surface of the stub end.
4.8 4.8 7.1 7.110.410.4
21.121.121.121.121.121.1
34.534.534.534.534.534.5
9/169/1611/1611/167/87/8
11/1611/1611/1611/163/43/4
6.56.56.56.56.56.5
74.974.974.974.974.974.9
56.556.556.556.556.556.5
8.98.98.98.98.98.9
80.880.882.382.385.185.1
SMSRSMSRSMSR
1/41/43/83/81/21/2
SFTC - 4 - SMSFTC - 4 - SRSFTC - 6 - SMSFTC - 6 - SRSFTC - 8 - SMSFTC - 8 - SR
Part No. FlangeSeat
Tube Size (inch)
DimensionsA B L1 L I h (inch) H (inch) D D1 d (Min)
Connects Fractional Port to Male AN
18.5419.0521.3324.8931.75
13.4613.4615.7417.5223.11
13.7115.7415.7418.2821.59
7/167/169/1611/167/8
3/89/169/1611/167/8
5/16-247/16-207/16-209/16-183/4-16
1/81/41/43/81/2
1/81/81/43/81/2
SAF - 2 - 2USAF - 2 - 4USAF - 4 - 4USAF - 6 - 6USAF - 8 - 8U
Part No.Tube O.D. D (inch)
AN TubeFlare Size
(inch)
StraightThreadT (U)
A LIWidth Across Flat
h (inch) H (inch)
*Note : GROOVE identifies serrated surface finish
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
34
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
Connects Fractional Tubes to AN Flared Tubes
1/81/81/4
5/163/83/81/23/41
1/81/41/45/161/43/81/23/41
5/16-247/16-207/16-201/2-207/16-209/16-183/4-16
1-1/16-121-5/16-12
1.52 2.28 4.31 5.84 4.31 7.11 9.9015.4921.33
7/161/21/29/165/85/8
13/161-1/81-3/8
7/167/169/165/8
11/1611/167/8
1-1/81-1/2
12.7012.7015.2416.2516.7616.7622.8624.3831.24
15.2415.2417.7818.5419.3019.3021.8421.8426.41
25.6528.4430.2230.9832.2532.2535.8143.1849.27
32.2535.0537.5938.3539.6239.6245.9753.3461.46
SAU - 2 - 2USAU - 2 - 4USAUI - 4 - 4USAU - 5 - 5USAUI - 6 - 4USAUI - 6 - 6USAUI - 8 - 8USAUI - 12 - 12USAUI - 16 - 16U
Part No.Tube O.D. D (inch)
AN TubeFlare Size
(inch)
StraightThreadT (U)
dMin A B LI
Width Across Flat
h (inch) H (inch)
Connects Fractional Port to AN Flared Tubes
37.0838.8639.6248.5156.1365.53
4.40 6.90 6.90 9.4014.8020.40
1/21/25/8
13/161-1/81-3/8
7/16-207/16-209/16-183/4-16
1-1/16-121-5/16-12
1/41/43/81/23/41
1/43/83/81/23/41
SAA - 4 - 4USAA - 6 - 4USAA - 6 - 6USAA - 8 - 8USAA -12 - 12USAA -16 - 16U
Tube O.D. D
(inch)
AN TubeFlare Size
(inch)
StraightThreadT (U)
Width Across Flath
(inch)E LPart No.
SAA An Adapter
SAUI An Union
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
35
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
Connects Fractional Tube to Female NPT Thread
1/81/41/43/83/83/81/2
1/81/81/41/43/81/21/2
2.28 4.82 4.82 7.11 7.11 7.1110.41
3/43/4
15/1615/161-1/81-5/161-5/16
7/169/169/1611/1611/1611/167/8
12.7015.2415.2416.7616.7616.7622.86
15.2417.7817.7819.3019.3019.3021.84
26.1627.6830.9832.5134.0339.6239.62
7.11 7.11 9.65 9.6510.4113.4613.46
32.7635.0538.3539.8741.4046.9949.78
-111-111-113-113-116-212-212
SOPC - 2 - 2NSOPCI - 4 - 2NSOPCI - 4 - 4NSOPCI - 6 - 4NSOPCI - 6 - 6NSOPCI - 6 - 8NSOPCI - 8 - 8N
Part No.Tube O.D.
D (inch)T*
(NPT)d
MinWidth Across Flat
h (inch) H (inch)BA I I1 L
O-RingUniform
Size Number
Connects Fractional Tube to Female Straight Thread
1/83/161/45/163/81/23/41
5/16-243/8-247/16-201/2-209/16-183/4-16
1-1/16-121-5/16-12
2.28 3.05 4.82 6.35 7.1110.4115.7522.35
9/165/83/47/8
15/161-1/81-1/21-3/4
7/161/29/165/8
11/167/8
1-1/81-1/2
12.7013.7115.2416.2516.7622.8624.3831.24
15.2416.0017.7818.5419.3021.8421.8426.41
26.1627.6830.9833.2735.0535.8142.1645.97
8.63 9.6510.4111.1711.9311.9314.2214.22
32.7634.2938.3540.6442.4145.9752.3258.16
-011-012-111-112-114-116-215-219
SOSC - 2 - 2USOSC - 3 - 3USOSCI - 4 - 4USOSC - 5 - 5USOSCI - 6 - 6USOSCI - 8 - 8USOSCI - 12 - 12USOSCI - 16 - 16U
Part No.Tube O.D.
D (inch)
StraightThreadT (U)
dMin
Width Across Flat
h (inch) H (inch)BA I I1 L
O-RingUniform
Size Number
SOSCI O-Seal Straight Thread Connector
SOPCI O-Seal Pipe Thread Connector
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
36
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
Connects Fractional Tubes to SAE/MS Straight Thread Boss
3-9023-9043-9063-9083-9103-9053-9043-9063-9083-9103-9063-9083-9103-9123-9083-9103-9083-9123-9143-9123-916
29.9734.0335.5637.5940.6434.7935.5637.0839.1142.1639.1141.9144.9549.0241.9145.2145.9749.0249.0253.3454.35
7.62 9.14 9.9011.1712.709.149.149.9011.1712.709.9011.1712.7014.9811.1712.7011.1714.9814.9814.9814.98
23.3626.6728.1930.2233.2727.4328.1929.7131.7534.7928.9531.7534.7938.8631.7535.0535.8138.8638.8641.1442.16
15.2417.7817.7817.7817.7818.5419.3019.3019.3019.3021.8421.8421.8421.8421.8421.8421.8421.8421.8426.4126.41
12.7015.2415.2415.2415.2416.2516.7616.7616.7616.7622.8622.8622.8622.8624.3824.3824.3824.3825.9031.2431.24
7/169/169/169/169/165/8
11/1611/1611/1611/167/87/87/87/811
1-1/81-1/81-1/41-1/21-1/2
7/169/1611/167/81
5/85/8
11/167/81
13/167/81
1-1/415/16
11-1/161-1/41-3/81-3/81-1/2
2.28 4.82 4.82 4.82 4.82 6.35 5.08 7.11 7.11 7.11 7.1110.4110.4110.4110.6612.7010.6615.7418.2816.7622.35
5/16-247/16-209/16-183/4-167/8-141/2-207/16-209/16-183/4-167/8-149/16-183/4-167/8-14
1-1/16-123/4-167/8-143/4-16
1-1/16-121-3/16-121-1/16-121-5/16-12
1/81/41/41/41/45/163/83/83/83/81/21/21/21/25/85/83/43/47/811
SSMC - 2 - 2USSMCI - 4 - 4USSMCI - 4 - 6USSMCI - 4 - 8USSMCI - 4 - 10USSMC - 5 - 5USSMCI - 6 - 4USSMCI - 6 - 6USSMCI - 6 - 8USSMCI - 6 - 10USSMCI - 8 - 6USSMCI - 8 - 8USSMCI - 8 - 10USSMCI - 8 - 12USSMC - 10 - 8USSMC - 10 - 10USSMCI - 12 - 8USSMCI - 12 - 12USSMC - 14 - 14USSMCI - 16 - 12USSMCI - 16 - 16U
Part No.Tube O.D.
D (inch)
StraightThreadT (U)
dMin
Width Across Flat
h (inch) H (inch)BA I I1 L
O-RingUniform
Size Number
SSMCI SAE/MS Male Connector
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
37
5612 Industrial Blvd. Edmond, OK 73034
Mounting Dimensions for O-Seal Connectors
*ALLOW CLEARANCE FOR FULL THREAD. Installation InstructionIn order to prevent the leakage with O-Seal Fittings, the surface perpendicular to the axis of the thread should be flat.When installing an O-Seal fitting, turn it until finger-tight. (The squeeze on O-Ring can be felt during the last 1/4 turn). After finger-tight installation, snug lightly with a wrench.When connecting the tubing to the connector, always use a back-up wrench on the O-Seal fitting hex so it does not turn while the nut is being tightened. Also use a back-up wrench when disconnecting a tubing connection.For a raised surface, such as Figure 1, it is recommended that the flat surface have a diameter at least as large as dimension “A” for the various size O-Seal fittings. This diameter is sufficient to allow metal-to-metal contact outside of the O-Ring sealing di ameter and to prevent O-Ring extrusion at high pressure.Figure 2 is an O-Seal fitting using with a counter bored or recessed hole. In this case, the diameter “B” is sufficient to allow the round shoulder of the O-seal to clear for proper installation. “D” gives the maximum depth that can be used with this diameter.Figure 3 shows the usage at deeper grooved or concaved area and “E” is the maximum depth that will allow a thin wrench (1/8”) to hold the O-Seal fitting while the connection is made to the tubing. The diameter “C” is sufficient to allow the hex of the fitting to turn in the recessed hole.
SOSC - 1 - 2USOSC - 2 - 2USOPC - 2 - 2NSOSC - 3 - 3U SOSC - 4 - 4U SOPC - 4 - 2NSOPC - 4 - 4NSOSC - 5 - 5USOSC - 6 - 6USOPC - 6 - 4NSOPC - 6 - 6NSOPC - 6 - 8NSOSC - 8 - 8USOPC - 8 - 8NSOSC - 12 - 12USOSC - 16 - 16U
5/16-245/16-24
-3/8-247/16-20
--
1/2-209/16-18
---
3/4-16-
1-1/16-121-5/16-12
--
1/8 NPT--
1/8 NPT1/4 NPT
--
1/4 NPT3/8 NPT1/2 NPT
-1/2 NPT
--
12.712.717.514.217.517.522.119.120.622.125.431.025.431.035.842.9
15.015.019.816.819.819.824.623.124.624.629.534.029.534.038.945.2
16.816.822.419.122.422.427.726.227.727.733.338.933.338.944.551.6
2.32.34.12.34.14.14.14.14.14.14.15.64.15.65.65.6
4.1 5.6 7.1 5.6 7.1 7.1 7.9 7.9 7.9 7.9 8.611.2 8.611.212.714.2
Basic Ordering Number
Straight Thread Pipe Thread A
Min. Dia. B
Min. Dia. C
Min. Dia.D
Max DepthE
Max Depth
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
38
5612 Industrial Blvd. Edmond, OK 73034
.
SAE/MS Straight Thread Positionable Elbows and Tees Installation Instructions
SAE/MS Internal Straight Thread Boss
1. Lubricate O-Ring with the lubricant which is applicable for the system fluid, environment and O-Ring material. (Standard O-Ring material is viton. Other O-Ring materials are also available). 2. Turn the fittings into the straight thread boss until the metal back-up washer contacts the face of the boss. At this moment, O-Ring gets into inclined groove.3. Until ’s end is oriented in the proper direction, position the fittings by turning to counter clockwise. (no more than 1 turning) 4. Until the washer contacts to the face of the bosses, tighten the fittings with wrench and back-up wrench.
.O : This surface would be perpendicular to the thread pitch diameter within 0.010 F.I.R (Full Indicator Reading) when measured at “O” diameter. D : This dimension applies only when tap drill cannot pass through the entire boss.
. Note: SAE/MS’s POSITIONABLE TEE and ELBOWS shall be compatible with SAE J1926, MS16142, or O-Ring female straight thread for JIS boss.
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
39
5612 Industrial Blvd. Edmond, OK 73034
Data for SAE/MS Straight Thread Boss
O-Ring for SAE/MS Fittings Bosses
5/16 - 243/8 - 24
7/16 - 201/2 - 20
9/16 - 18
6.07 7.65 8.9210.5211.89
1.631.631.831.831.98
3-9023-9033-9043-9053-906
Thread size Inside Dimension(mm)
Cross Section(mm)
O-Ring Size No.
33/4 - 167/8 - 14
1-1/16 - 121-3/16 - 121-5/16 - 12
16.3619.1823.4726.5929.74
2.212.462.952.952.95
3-9083-9103-9123-9143-916
Thread size Inside Dimension(mm)
Cross Section(mm)
O-Ring Size No.
12
12
12
12
12
15
15
15
15
15
15
15
15
0.672
0.750
0.828
0.906
0.969
1.188
1.344
1.625
1.765
1.910
2.270
2.560
3.480
0.358
0.421
0.487
0.550
0.616
0.811
0.942
1.148
1.273
1.398
1.713
1.962
2.587
0.062
0.062
0.062
0.062
0.062
0.094
0.094
0.094
0.094
0.125
0.125
0.125
0.125
0.468
0.468
0.547
0.547
0.609
0.688
0.781
0.906
0.906
0.906
0.906
0.906
0.906
0.438
0.500
0.563
0.625
0.688
0.875
1.000
1.250
1.375
1.500
1.875
2.125
2.750
0.074
0.074
0.093
0.093
0.097
0.100
0.100
1.130
1.130
0.130
0.132
0.132
0.132
0.390
0.390
0.454
0.454
0.500
0.562
0.656
0.750
0.750
0.750
0.750
0.750
0.750
0.062
0.125
0.172
0.234
0.297
0.391
0.484
0.609
0.719
0.844
1.078
1.312
1.781
0.277
0.340
0.395
0.457
0.515
0.696
0.614
0.990
1.115
1.240
1.553
1.803
2.428
0.267
0.330
0.383
0.446
0.502
0.682
0.798
0.972
1.097
1.222
1.535
1.785
2.410
0.2902
0.3528
0.4104
0.4731
0.5323
0.7159
0.8356
1.0158
1.1409
1.2659
1.5785
1.8287
2.4540
0.2854
0.3479
0.4050
0.4675
0.5624
0.7094
0.8286
1.0084
1.1334
1.2584
1.5709
1.8209
2.4459
5/16 - 24
3/8 - 24
7/16 - 20
1/2 - 20
9/16 - 18
3/4 - 16
7/8 - 14
1 1/16 - 12
1 3/16 - 12
1 - 61/5 12
15/8 - 12
17/8 - 12
2 1/2 - 12
1/8
3/16
1/4
5/16
3/8
1/2
5/8
3/4
7/8
1
1 1/4
1 1/2
2
B / Straight Thread
Nom.Tube.O.D
Thread Size
Pitch Dia Minor Dia
Min Max Min Max Min Min
DDia
Full Thread Depth
+0.015-0.000
K
Min
O Dia
Min
P④
Min
S② ③
Max
U②Dia
Y①Dia
±1Deg
Z
① Diameter U shall be concentric with thread pitch diameter within 0.005 full indicator reading (FIR) and shall be free from longitudinal and spiral tool marks. Annular tool marks shall be less than 100 micro inches.② This is the maximum recommended spotface depth to permit sufficient wrench grip for proper tightening of the fitting or locknut③ If the surface of boss surface is machined, dimensions Y and S does not need to be applied.④ Bottoming tap shall be used to satisfy the tap drill depth. Where standard taps are used, the drill depths must be increased accordingly.
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
40
WELD END
VENT PROTECTOR
PLUG & CAP
SPWCI Male Pipe Weld Connectorpage 42
SMPWEI Male Pipe Weld Elbowpage 42
SSWCI Socket Weld Connectorpage 43
SSWEI Socket Weld Elbowpage 43
SP Plugpage 44
SCI Cappage 44
SNI Nut
SFF Front Ferrule
page 44
SBF Back Ferrule
page 44
SFS Ferrule Set
SI Insert
page 45
page 45
page
45
SVPVent Protectorpage 43
Weld End, Vent Protector,Plug & Cap, Spare Part
SPARE PARTS
©
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
..Weld end Usage Informations:. Do weld after removing nut and ferrules from body to protect them from weld heat.
Do protect thread end or pot and seat area of body with another nut and plug (for easy disassembly just finger tighten it). Correct weld procedure is required during welding and after weld compilation. Suitable heat treatment must be carried out in accordance with industry or your own standard.
Connects Fractional Tubes to Pipe
1/83/161/41/45/165/163/83/83/81/21/21/25/83/41
1/81/81/81/41/81/41/43/81/23/81/23/41/23/41
10.3010.3010.3013.7010.3013.7013.7017.1021.3017.1021.3026.6721.3026.6733.40
2.28 3.04 4.82 4.82 5.08 6.35 7.11 7.11 7.1110.4110.4110.4112.7015.7422.35
7/167/161/29/169/169/165/8
11/167/8
13/167/8
1-1/1615/161-1/161-3/8
7/161/29/169/165/85/8
11/1611/1611/167/87/87/81
1-1/81-1/2
12.7013.7115.2415.2416.2516.2516.7616.7616.7622.8622.8622.8624.3824.3831.24
15.2416.0017.7817.7818.5418.5419.3019.3019.3021.8421.8421.8421.8421.8426.41
23.8724.6325.4030.4826.6731.2432.5132.5138.8633.2738.8640.3838.8640.3850.03
9.65 9.65 9.6514.229.6514.2214.2214.2219.0514.2219.0519.0519.0519.0523.87
30.4831.2432.7637.8434.0338.6039.8739.8746.2243.4349.0250.5449.0250.5462.23
SPWC - 2 - 2PSPWC - 3 - 2PSPWCI - 4 - 2PSPWCI - 4 - 4PSPWC - 5 - 2PSPWC - 5 - 4PSPWCI - 6 - 4PSPWCI - 6 - 6PSPWCI - 6 - 8PSPWCI - 8 - 6PSPWCI - 8 - 8PSPWCI - 8 - 12PSPWC - 10 - 8PSPWCI - 12 - 12PSPWCI - 16 - 16P
Part No.Tube O.D.
D (inch)
dMin
Width Across FlatMale Pipe Sizep
h (inch)Nom. H (inch)O.D.BA I I1 L
SPWCI Male Pipe Weld Connector
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
23.3725.4033.02
26.9030.4836.06
14.2214.2219.05
19.5523.1125.90
17.7819.3021.84
15.2416.7622.86
9/1611/167/8
1/25/8
13/16
4.82 7.1110.41
13.7013.7021.30
1/41/41/2
1/43/81/2
SMPWEI - 4 - 4PSMPWEI - 6 - 4PSMPWEI - 8 - 8P
Part No. dMin
Tube O.D. D (inch) A B LI I1 L1
Width Across FlatPipe Size (P)h (inch)Nom. (inch) H (inch)O.D
Connects Fractional Tubes to Pipe
SMPWEI Male Pipe Weld Elbow
42
5612 Industrial Blvd. Edmond, OK 73034
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
1/81/43/81/23/41
2.28 4.82 7.1110.4115.7422.35
7.8711.1715.7419.0526.6733.27
7/161/25/8
13/161-1/161-3/8
7/169/1611/167/8
1-1/81-1/2
12.7015.2416.7622.8624.3831.24
15.2417.7819.3021.8421.8426.41
22.3526.1630.2230.9833.2740.38
6.35 7.87 9.6512.7014.2219.05
28.9533.5237.5941.1443.4352.57
8.6310.4111.9311.9311.9314.22
SSWC - 2SSWCI - 4SSWCI - 6SSWCI - 8SSWCI - 12SSWCI - 16
Part No. dMin PTube O.D.
D (inch) A B LI I1 L1Width Across Flat
h (inch) H (inch)
Connects Fractional Tubes
1/43/81/23/41
4.82 7.1110.4115.7422.35
12.7015.7520.5726.9235.05
1/25/8
13/161-1/161-3/8
9/1611/167/8
1-1/81-1/2
15.2416.7622.8624.3831.24
17.7819.3021.8421.8426.41
19.5523.1125.9029.7136.83
7.87 9.6512.7014.2219.05
26.9230.4836.0639.8749.02
19.5523.1125.9029.7136.83
SSWEI - 4SSWEI - 6SSWEI - 8SSWEI - 12SSWEI - 16
Part No. dMin PTube O.D.
D (inch) A B LI I1 L1Width Across Flat
h (inch) H (inch)
Connects Fractional Tubes
SSWCI Tube Socket Weld Connector
SSWEI Tube Socket Weld Elbow
SVP Vent Protector
SVP - 4NSVP - 6NSVP - 8NSVP - 12N
1/43/81/23/4
19.8120.5726.1626.92
14.2214.2219.0519.05
7.1110.4112.7018.29
9/1611/167/8
1-1/16
Part No. T(NPT) L L1 d H
(inch)
* ISO Tapered Threads are available upon requestAll dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
43
5612 Industrial Blvd. Edmond, OK 73034
SP Plug
SCI Cap
Fractional
SP - 2SP - 3SP - 4SP - 5SP - 6
1/83/161/45/163/8
7/161/29/165/8
11/16
Width Across FlatH (inch)
Tube O.D. D (inch)Part No.
SP - 8SP - 10SP - 12SP - 14SP - 16
1/25/83/47/81
7/81
1-1/81-1/41-1/2
Width Across FlatH (inch)
Tube O.D. D (inch)Part No.
Plugs Unused port of Metric fittingsPlug provides plugging fitting portInstallation instruction1. With wrench, 1/4 turn from finger-tight position. (1/8 turn for 1/8 3/16 2, 3, 4 size plug)2. Remove nut and ferrules from body
Connects Caps End of Fractional Tubes
SC - 1SC - 2SC - 3SC - 4SC - 5SC - 6SC - 8SC - 10SC - 12SC - 14SC - 16
1/161/83/161/45/163/81/25/83/47/81
5/167/167/161/29/165/8
13/1615/161-1/161-3/161-3/8
5/167/161/29/165/8
11/167/81
1-1/81-1/41/1/2
8.6312.7013.7115.2416.2516.7622.8624.3824.3825.9031.24
10.9215.2416.0017.7818.5419.3021.8421.8421.8421.8426.41
11.2013.4614.7316.0017.0118.2819.0519.8123.3323.8726.16
14.9820.0621.3323.3624.3825.6529.2129.9733.4934.0338.35
Width Across Flath (inch) H (inch)
Tube O.D. D (inch)Part No. A B I L
Installation instruction1. With wrench, 1-1/4 turn from finger-tight position. (3/4 turn for 1/8 3/16 3mm, 4mm)2. Insert tube end into cap
SNI Nut
SFF Front Ferrule
Fractional
SN - 1SN - 2SN - 3SN - 4SN - 5SN - 6
1/161/83/161/45/163/8
5/167/161/29/165/8
11/16
7.9011.9311.9312.7013.4614.22
Width Across FlatH (inch)
Tube O.D. D (inch) LPart No.
SN - 8SN - 10SN - 12SN - 14SN - 16
1/25/83/47/81
7/81
1-1/81-1/41-1/2
17.5217.5217.5217.5220.6
Width Across FlatH (inch)
Tube O.D. D (inch) LPart No.
Fractional
SFF - 1SFF - 2SFF - 3SFF - 4SFF - 5SFF - 6
1/161/83/161/45/163/8
Tube O.D. D (inch)Part No.
SFF - 8SFF - 10SFF - 12SFF - 14SFF - 16
1/25/83/47/81
Tube O.D. D (inch)Part No.
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
44
5612 Industrial Blvd. Edmond, OK 73034
SBF Back Ferrule
SFS Ferrule Set
Fractional
SBF - 1SBF - 2SBF - 3SBF - 4
SBF - 5SBF - 6SBF - 8SBF - 10
SBF - 12SBF - 14SBF - 16
1/161/83/161/4
5/163/81/25/8
3/47/81
Tube O.D. D (inch)Part No. Tube O.D.
D (inch)Part No. Tube O.D. D (inch)Part No.
Fractional
SFS - 1SFS - 2SFS - 3SFS - 4
SFS - 5SFS - 6SFS - 8SFS - 10
SFS - 12SFS - 14SFS - 16
1/161/83/161/4
5/163/81/25/8
3/47/81
Tube O.D. D (inch)Part No. Tube O.D.
D (inch)Part No. Tube O.D. D (inch)Part No.
SI Insert
Fractional
SI - 3 - 2SI - 4 - 2SI - 4 - 3SI - 5 - 2SI - 5 - 3SI - 5 - 4SI - 6 - 3SI - 6 - 4
3/161/41/45/165/165/163/83/8
1/81/83/161/83/161/43/161/4
2.282.283.552.283.044.823.044.82
SI - 8 - 4SI - 8 - 6SI - 10 - 6SI - 10 - 8SI - 12 - 8SI - 12 - 10SI - 16 - 12
1/21/25/85/83/43/41
1/43/83/81/21/25/83/4
4.827.877.87
11.1711.1714.2217.52
Part No. Tube O.D. (inch)
Tube I.D. (inch) Part No. Tube O.D.
(inch)Tube I.D.
(inch)I.D. of Bore I.D. of Bore
All dimensions in millimeters unless specified as “inch” • Dimensions are for reference only, subject to change.
www.mako-products.net
Phone: 405-509-2665 Fax: 866-239-1587• •
©
45
MAKO WARRANTY:All products distributed from Mako Products, LLC are guaranteed to be free from manufacturing defects for a period of one year from the date of shipment. If the product is determined to be defective within that period, the product will be replaced at no charge to the buyer if it falls under one or more of these specific conditions: (1) product failure was a result of a manufacturing defect and not damaged from an accident, alteration, misuse, abuse or contact with corrosive fluids, (2) the product was installed with proper care and operating practices, (3) proper notice and description of defective product was recorded to Mako Products, LLC before the product was shipped back from the buyer.
WARRANTIES
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
Superlok Quality Certifications
Bite type fitting for DIN2353
SUPERLOK Tube Fitting
37° Flared Tube Fittings for SAE J514
SUPERLOK compression tube fitting
Bite type compression tube fitting
SAE 37° Flared Tube Fittings
Bite Type Tube Fitting According to DIN2353
SUPERLOK Tube Fittings
Superlok & Bite Type (JIS & KS)
Superlok & Bite Type Tube Fittings
Superlok & Bite type (DIN2353)
DIVISION PRODUCTS CERT. NO CERTIFYING AGENCYFittings & Valves 06-BK152666-PDA
06-BK150238-PDA
06-BK294147-PDA
P-12285
P-12317
P-12675
44879-07HH
44880-07HH
TA09512M
20040/A0 BV
06/10006
ABS Cert. of Design Assessment
DNV Cert. of Type Approval
Lloyd’s Register Cert. of Type Approval
NK
BV
ABS Cert. of Design Assessment
ABS Cert. of Design Assessment
DNV Cert. of Type Approval
DNV Cert. of Type Approval
Lloyd’s Register Cert. of Type Approval
Lloyd’s Register Cert. of Type Approval
CertificationsSuperlok, BMT Co. & Mako Products
TYPE ISSUING BODY SCOPE CERTIFICATE NO.
ISO 9001 AP0379
Superlok Manufacturing CertificationsNO.
1
23
456
7
8
ASME N STAMP
ASME NPT STAMP
ASME NS
ASI 6D
API Q1PED/97/23/EC
(Module H)
KEPIC-MN
HSB
ASME
API
API
HSB
KEA
N-3409
N-3410
N-3411
6D-0699
Q1-0375
HSBI-10-07-074
MN-288
Design and Manufacture of Fittings (High Pressure Forged, Super Clean, Tube & Pipe), Valves & Industrial Machinery Parts and Equipment and MCPD (Molded Case Power Distributor) For
Distribution Switchboards
Purchase, Construction, Fabrication, Manufacture, and Inspection of Class 1, 2, & 3 Products
Using Official API Monogram on Manufacturing Valves
Design & Manufacturing of Fittings & Valves
Design, Manufacturing, Installation and service of Valves & Fittings
Design & Manufacturing of Fittings & Valves for Class 1, 2, & 3 Grade
46
RETURN POLICYRETURN POLICY: 1. ERRORS: Regarding administrative or shorthand work - all quotations, orders, confirmations, invoices and other documents are subject to correction. 2. RETURNS: Before products are returned, the correct form of authorization must be recorded to Mako Products, LLC. Buyers must acquire acknowledgement that an RMA (Return Merchandise Authorization) was created for the items being returned with the precise quantity for maximum assurance of returned credit. Shipping expenses should not be assumed unless they are verified from Mako Products, LLC. For guidelines on free returns, refer to ERRORS. Customer specified items are deemed non-returnable. 3. RESTOCKING FEE: Returned products from customers may be subject to a restocking fee of 20%. 4. TRANSIT DAMAGE: Notification to Mako Products, LLC is required if loss, damage or shortage of products via carrier should occur. All claims should be made as soon as possible and no later than five days after receipt of shipment. Loss or damage to materials is the responsibility of the carrier. 5. CANCELLATION: Any regular stock item on back order is considered free of cancellation fee if the buyer wishes to waive the item. For special manufactured items, the cancellation charges may be up to 100%.
Shipping expenses should not be assumed until verification and authorization have been granted from Mako Products, LLC.
SUPERLOK WARRANTY:BMT warrants that Superlok tube fittings shall be free from defects in material and workmanship for the life of the product. The purchaser’s solution shall be limited to replacement and installation of any parts that fail through a defect in material or workmanship.Superlok tube fittings are manufactured to be 100% interchangeable with other tube fittings currently on the market. Superlok fully warranties the compatibility of it’s fittings with other manufacturers, provided the same strict manufacturing practices and tolerances are held by those manufacturers.
CONSUMERS MUST ABIDE BY THE SPECIFIC INSTALLATION GUIDES AND OPERATION PROCEDURES WITH THIS EQUIPMENT OR
THEY WILL NOT BE CONSIDERED REPLACEABLE.
Mako Products, LLC Return Policy & DisclaimerATTENTION: Please read carefully before using our products.
5612 Industrial Blvd. Edmond, OK 73034
Medium & High Pressure Needle Valve 20-60K PSI
www.mako-products.netPhone: 405-509-2665 Fax: 866-239-1587• •
©
47
sevlaV wolF ssecxE lairtsudnI & seireS evlaV kcehC
High Pressure Check ValvesSHCV SERIES
Technical Data
Seal Materials Cracking Pressure and Reseal Pressure at 70 (20 )
Materials of Construction
All valves are factory tested for cracking pressure and reseal performance.
To order add the seal material designator to the ordering number.ex) SHCV1-S8-1P-N
Testing
Features■ Pressure rating up to 6,000psig(413bar) at 100 (37 )■ Temperature rating up to 375 (190 ) with viton seal standard■ Cracking pressure fixed from 1/3 to 25psig (0.02 to 1.7bar) ■ Variety of end connections ■ 316 stainless steel body material as standard.■ Each and every valve is tested at the factory.
Series Orifice (mm)Working and Back
Pressure@70 (20 )
Flow CoefficientCv
NominalCracking Pressure
SHCV1 4.86000psig (413bar)
0.67 1/3, 1, 5, 10, 25 psig
(0.02, 0.06, 0.34, 0.68, 1.7 bar)SHCV2 7.8 1.80SHCV3 15.0 5000psig (344bar) 4.70
Material Temperature Rating DesignatorViton -10 to 375 (-23 to 190 ) StandardNBR -10 to 250 (-23 to 121 ) N
Ethylene Propylene -50 to 300 (-45 to 148 ) E
No. Component Material1 Inlet Body A276-3162 Outlet Body A276-3163 Poppet Viton-bonded SS3164 Poppet Stopper Stainless Steel 3165 O-Ring Viton(Standard)6 Packing PTFE7 Spring Stainless Steel 304
Nominal Spring Size
psig(bar)
Cracking Pressure Range
psig(bar)
Min. ResealPressure psig(bar)
Designator
1/3 (0.02) 0~3 (0~0.20) 6 (0.41) back pressure 0.3P1 (0.068) 0~4 (0~0.27) 5 (0.34) back pressure 1P5 (0.34) 3~9 (0.20~0.62) 2 (0.13) back pressure 5P10 (0.68) 7~15 (0.48~1.0) 3 (0.20) 10P25 (1.7) 20~30 (1.3~2.0) 17 (1.1) 25P
408 Wimbledon Rd. www.mako-products.netEdmond, OK 73003 Phone: 405-509-2665 Fax: 866-239-1587/ / / /4
©
Instrument Fittings
Relief Valves Quick Connectors Plug ValvesIntegral & Union Bonnet
Needle Valves
SBV210 Series1K Compression Ball Valve
SBV120H Series3K Compression Ball Valve
SBV360H Series6K Compression Ball Valve
SBVF360 Series6K Forged High Pressure Ball Valve
High Pressure Fittings20-60K PSI Bar Stock Needle Valve Check Valves
Swing-Out Ball Valves Instrumentation Manifolds, Gauge Valves & Block & Bleeds
Micron Inline & Tee Filter Ultra Pure Fittings
JIC Fittings37° Fittings
Threaded Check ValvesICS6 Series
Stainless Tubing316 or 304 Welded or Seamless, Stick & Coil
Threaded Ball ValvesReduced Port SS & CS Full Port SS & CS
Threaded Needle ValvesMini Valves, Angle Valves, Bleed Valves, Standard Valves, Gauge Valves
Threaded Ball Valves
Additional Products Available
5612 Industrial Blvd. Edmond, OK 73034
“Red Ring”
Valve SeriesBall ValvesIntegral Bonnet Needle ValvesUnion Bonnet Needle ValvesCheck ValvesHigh Pressure Check ValvesHigh Pressure Needle ValvesPlug Valves
Manifold ValvesDouble Block & Bleed ValvesSwing-Out Ball ValvesToggle ValvesBleed & Purge ValvesQuick ConnectorsHigh Pressure Ball Valves
Hydraulic Ball ValvesTrunnion Ball ValvesRising Plug ValvesRelief ValvesCryogenic Needle ValvesCryogenic Ball ValvesMicron In-Line Filters
..........
.......... ......
SS & CS BALL VALVESSS & CS BALL VALVES
SS & CS NEEDLE VALVESSS & CS NEEDLE VALVES
COIL & STICK TUBINGCOIL & STICK TUBING
TUBE END BALL VALVESTUBE END BALL VALVES
INSTRUMENT FITTINGSINSTRUMENT FITTINGS
5612 Industrial Blvd.www.mako-products.net
Edmond, OK 73034Phone: 405-509-2665 Fax: 866-239-1587
••
Tube Fittings, Instrument Fittings, Ball Valves, Needle Valves,
Coil & Stick Tubing and more!
©
Fitting SeriesInstrument Thread Fittings37 Flared Tube Fittings (JIC)O-Ring Face Seal FittingsHose Connectors Push-On Hose Fittings
top related