rc8.2e rtr manual and catalog 6 19 2012
Post on 25-Jul-2015
350 Views
Preview:
TRANSCRIPT
6/1
2
2:: Introduction
:: RC8.2e Platform Features
:: Other Helpful Items
Associated Electrics, Inc.26021 Commercentre Dr.Lake Forest, CA 92630
http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook
Customer ServiceTel: 949.544.7500Fax: 949.544.7501
Thank you for purchasing this Team Associated product. This manual contains instructions and tips for building and maintaining your new RC8.2e RTR. Please take a moment to read through it an familiarize yourself with these steps as they will help you to understand each component’s function and show you some tips for getting the most out of your RC8.2e RTR. We are continually changing and improving our designs; therefore, actual parts may appear slightly different than the illustrations.
• XP SC1300-BL ESC with Deans (TM) Ultra plug (works with 3S 11.1V or 4S 14.8V Lipo)• Reedy 2000 KV motor• High torque S2008MG Metal Gear Servo• XP-SSi 2.4Ghz Radio System• RC8e body with air scoops (#89523)• RC8.2 racing suspension• Low CG, 3mm thick 7075 Aluminum shock towers• 16mm Big-Bore Aluminum Shocks bodies and Caps with Pre-load Clips• Rubber shock boots• Upgraded Dual bell-crank steering with reduced bump-steer• Black hard-anodized 7075 Alum. Chassis with keyed suspension plates• Aluminum steering knuckles for improved durability• Alloy Steel Turnbuckles• Caster blocks adjust 14, 16, or 18 degrees with molded inserts• 10 mm thick arms• Molded suspension pivot bushings for adjustable pivot height• 4.30:1 ratio gearboxes • Molded composite front and rear chassis braces• Rigid one-piece motor mount utilizes standard motor screw mounting pattern• Lowered, lightweight wing mount• Large speed control mounting area raised off of chassis to allow for easy screw mounting of common speed controllers• Speed control mounting area includes convenient switch-mounting boss• Utilizes 3 hook-and-loop straps to secure LiPo batteries into battery tray• Molded Battery tray supports 7.4 -14.8V battery packs with room for foam pads• Requires 3S 11.1 V or 4S 14.8 V LiPo battery pack with Deans (R) Ultra Plug (R) (recommended #626 LiPo 14.8V, 5500 mAh, 60C, #733 LiPo 14.8V, 3700mAh, 35C).• Sealed receiver box for proper electronics placement• Receiver, Servo, and battery tray remove from car in one piece for easy maintenance and cleaning• Convenient wire routing keeps critical electronic wires out of drivetrain components and simplifies disassembly• Includes pinion gear (17T) and molded spur gear (46T)
Your RC8.2e RTR requires the following items to complete your kit:
• Transmitter batteries (#302, 303 recommended)• 3S 11.1v LiPo battery pack with Deans (TM) Ultra plug-OR-• 4S 14.8v LiPo battery pack with Deans (TM) Ultra plug (AE #626, 733)• Battery charger (peak detection charger recommended) (AE #604)• Needle nose pliers • Hobby knife • Reamer/hole punch • Ride Height Gauge (#1449 recommended)
• Silicone Shock Fluid / Differential Fluid (Refer to catalog for complete listings)• Body Scissors (AE Part # 1737) • Wire cutters • Soldering Iron • FT Threadlock (#1596)• FT Hex Wrenches (AE Part # 1541, 1655) • Multi Tool (AE Part #7494) • FT Turnbuckle Wrench (#89240)• FT Nut Drivers (AE Part #1561, 1663-1668) • Calipers or a Precision Ruler • Green Slime shock lube (AE Part # 1105)
:: Additional Items Needed
3
24-25.........Shocks Install
25-30.........Radio Tray Assembly
30-31.........Wheel, Tires, and Body Assembly
32-34.........TechTips
35-44.........Catalog
44................Contact Info
45-46.........Notes
47.................Setup Sheet “Kit Setup”
48................1:1 Hardware “Fold Out
49................Setup Sheet “Blank”
50................Back Cover
:: Table of Contents
:: Notes
This symbols indicates a special note or instruction in the manual.
!There is a 1:1 hardware foldout page in the back of the manual. To check the size of a part, line up your hardare with the correct drawing until you find the exact size. Each part in the foldout has a number assigned to it for ordering replacement parts.
1....................Cover
2....................Introduction
3....................Table of Contents
4-5...............Front and Rear Diff Assembly
6-7................Center Diff Assembly
7-8...............Steering, Servo, and Rear Camber Links Assembly
8-10.............Shocks Assembly
10.................Chassis Assembly
10-12..........Steering Assembly
12-13..........Front Geaerbox Assembly
14-17..........Front Suspension Assembly
17-19.........Rear Gearbox Assembly
19-22.........Rear Suspension Assembly
22-23.........Center Bulkhead Assembly
Associated Electrics, Inc.26021 Commercentre Dr.Lake Forest, CA 92630
http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook
Customer ServiceTel: 949.544.7500Fax: 949.544.7501
4:: Front/Rear Differential Assembly
:: Front/Rear Differential Assembly (cont.)
:: Front/Rear Differential Assembly (cont.)
89120Diff
outdrive pin
89120Sun gear
89120Spider gear
assembly
252368x16mmbearing
89496Diff
outdrive16mm
89121Diff
O-Ring
89115Diff
housing
Align pin with groove in sun gear
!
#658
8
blac
k gr
ease
pin
89120Diff
washer
89121Diff
O-Ring
#6588
black grease
5:: Front/Rear Differential Assembly (cont.)
:: Front/Rear Differential Assembly (cont.)
:: Front/Rear Differential Assembly (cont.)
89120Diff
outdrive pin
89116Diff
gasket
252368x16mmbearing
89113Diff ring
gear
89121Diff
O-Ring89121
Diff O-Ring89496
Diff outdrive16mm
Align pin with groove in sun gear
!
#6588
black grea
se
#6588
black grease
#6588black grease
89120Sun gear
89120Diff
washer
892083x14mm
fhcs
x4
Diff fluid5,000cst#5453
Tighten screws evenly and firmly.
Fill with diff fluid to top of gears.
!
!
Build front and rear diffs!
!
6:: Center Differential Assembly
:: Center Differential Assembly (cont.)
:: Center Differential Assembly (cont.)
Align pin with groove in sun gear
!
89120Sun gear
89115Diff
housing
252368x16mmbearing
89121Diff
O-Ring
89496Diff
outdrive16mm
89120Diff
washer
89121Diff
O-Ring
89519Plastic
spur gear(46T)
89496Diff
outdrive16mm
252368x16mmbearing
89121Diff
O-Ring
#6588
black grease
#6588
black grease
#658
8
blac
k gr
ease
89120Diff
outdrive pin
89120Spider gear
assembly
7:: Center Differential Assembly (cont.)
:: Center Differential Assembly (cont.)
:: Steering Turnbuckle Assembly
Align pin with groove in sun gear
!
89120Sun gear
89116Diff
gasket
#6588black grease
89120Diff
outdrive pin
89120Diff
washer
89121Diff
O-Ring
892083x14mm
fhcs
x4
Tighten screws evenly and firmly.
Fill with diff fluid to top of gears.
!
!Diff fluid5,000cst#5453
89074Steering eyelet
89075Steering ballstud
17.8mm
8926842mm steel turnbuckle
x2
x2
Build right and left sides!
!
8:: Servo Link Assembly
:: Rear Camber Link Assembly
:: Shock Assembly
89076Camber
ball joints
89076Camber
pivot balls
89076Camber rod end
8926938mm steel turnbuckle
x2
x2
x2
Build right and left sides!
!7.7mm
89358Lower
shock tool
x289066Shock
O-rings
89352Spacer
89358Lower
Use the lower shock tool to load the two o-rings
and spacer for easy lubing and installation
into the shock body
!Shock fluid
8958016x29mmRTR shock
body (front)
8958216x38mmRTR shock
body (rear)
89078Straight eyelet
8926732mm steel turnbuckle
x2
7.5mm 89078balljoint
x2
9:: Shock Assembly - (cont.)
:: Shock Assembly - (cont.)
:: Shock Assembly - (cont.)
89335Shock cap
89396Shock collar
89351Shock
bladder
Some residual shock fluid may appear from
your first few runs around the shock cap as a result of bleeding.
!
Bladder Installation
As you install the shock cap with the bladder, it will force out any extra fluid. If you install the cap with the shaft fully extended, you are running FULL REBOUND.
To run less rebound, unthread the cap 1-2 turns and compress the shaft to the desired position and re-tighten the cap with the shaft compressed.Start with no rebound.
A B C
89065Shock
rod end
Short boots for front shocks.
Long boots forrear shocks.
!
89556RC8.2
shock boot (front shown)
89065Shock rodend ball
Fill to top with shock fluid:
Front: 30wtRear 30 wt
#5422
Shock
fluid
x2892782.5mm piston washer
89353Shock piston
set (1.3, blank)
89215Locknut(piston)
89352O-Ring
89352Bottom
nut
89358Upper shock tool
!Shock fluid
One drop of shock
fluid on threads.
!
89261Shock shaft, 38mm (rear)
89260Shock shaft,
29mm, (front)
10:: Shock Assembly - (cont.)
:: Chassis Assembly
:: Steering Assembly
89258Front
chassis brace
25215M3
locknut
894553x22mm
fhcs
89010Top plate(lower)
3 dot down
hinge pin bushing
89476RC8B
+3mmchassis
89552Side guards(left & right)
252013x8mm
fhcs
x4
x2
Note: cut fuel tubing brace off of the left side guard.
!
89293Front spring, silver (3.9lbs)(short spring)
89348Rear spring,
silver (3.3lbs)(long spring)
8935416mm shock
spring cup
x2
x2
Build two front and two rear shocks!
!
89396Shock
pre-load clips
89396Shock
pre-load clips
Front shock: 7mmRear shock: 2mm
10mm
5mm
3mm
2mm
1mm
89552Side guards(left & right)
252013x8mm
fhcs
x4x4
x2x2Side guards
25215M3
locknut
252033x12mm
fhcs
252023x10mm
fhcs
252023x10mm
fhcs
89010Top plate(upper)
89011Top plate(upper)
89039Hinge pin bushing
(3 dot down)
x2
x4
x4
11:: Steering Assembly (cont.)
:: Steering Assembly (cont.)
:: Steering Assembly (cont.)
89016Servo saver bolt
89015Servo saver arm
89015Servo saver
bellcrank
#6588black grease
#1596thread lock
252043x16mm
fhcs
314046x10mmbearing
314046x10mmbearing
89015Steering bellcrank
89272Steering
rack
25215M3
locknut
25215M3
locknut
89218Washer3x8mm
89117Diff shim
89014Steering rack post
891615x8mmbearing
89016Servo saver spring
89016Servo saver
retainer
x2
x2
x2
x2
x2
x4
x2
x2
x2
gap setting:2mm
!
Smooth edge towards drivers side!
!89013
Steering posts
x2
12:: Steering Assembly (cont.) / Front Gearbox Assembly
:: Front Gearbox Assembly - (cont.)
:: Front Gearbox Assembly - (cont.)
x2
x4
89017Inner
gearbox
89114Diff pinion
gear
892243x16mm
shcs
892012.5x3mm
bhcs
892782.5mmwasher
892215x4mmsetscrew
x2
x2
x2
Key setscrew onto flat side of shaft.Tighten with no
endplay.
!
#1596
thread lock
892183x8mm washer
89036Arm
mount (B)
x2
252368x16mmbearing
25215M3 locknut
89571SC8.2e
center drive line input
cup
25215M3 locknut
892263x26mm
shcs
892144x12mm
fhcs
x2
#1596thread lock
#1596thread lock
#1596thread lock
13:: Front Gearbox Assembly - (cont.)
:: Front Gearbox Assembly - (cont.)
:: Front Gearbox Assembly - (cont.)
Diff shims installed to diff, diff installed to
gearbox.
!
89076Camber rod ends
8926938mm steel
turnbuckle
89549Front
upper arm
Build right and left sides!
!Smooth edge towards drivers side!
7.5mm
1 dot
hinge pin bushing
89473Steel shock
standoffs
892183x8mm washer
89586RC8.2e RTRshock tower
(front)
892253x24mm
shcs
x2
x2
x2
#1596
thread lock
#1596
thread lock
892023x12mm
bhcs
89040Inner
hinge pin
89039Hinge pin bushing (1 dot)
x2
x4
x2
892243x16mm
shcs
89472Front
bulkhead spacer
89117Diff shim
89017Outer
gearbox
x2
x2
!
!
14:: Front Suspension Assembly
:: Front Suspension Assembly - (cont.)
:: Front Suspension Assembly - (cont.)
Build Two!!
89573Lightweight cv axle, steel
89105CVA
u-joint coupler
89102CVA bone
89105CVA pin
#6588
black grease
#6588black grease
Axle has additional holes for crosspin to extend
the life of the Axle.
!!
Left Side
Build right and left sides!
!
8916215x21x4mm
bearing
892215x4mmsetscrew
89251Wheel hex
89096Wheel hex
pins89028
Steering block(left, right)
252368x16x5mm
bearing
#15
96th
read
lock
89558Caster blocks
(left, right)
Note:One drop only.Spread evenly
inside the threads.
#1596thread lock
#1596thread lock
#1596thread lock
15:: Front Suspension Assembly - (cont.)
:: Front Suspension Assembly - (cont.)
:: Front Suspension Assembly - (cont.)
Do not tighten until bushing is keyed
into steering block.
!
!
!Note:
Key bushings into steering block.
251923x20mm
shcs
89511Swaybar ball joint
89091Swaybar
joint
46713x10mmsetscrew
89511Swaybareyelet
892204x12mmsetscrew
89550RC8.2
front arms(left, right)
Build right and left sides!
Build right and left sides!
Droop screw
placement!
Build Two!
!
!
!
!
!
!
8903216 deg. caster angle bushing
(blue)
8903216 deg. caster angle bushing
(red)
Build right and left sides!
!
Note: direction
blue
red
16 deg
16 deg
315202.5x6mm
bhcs
89041Outer
hinge pin
892074x12mm
bhcs
89029Steering
block bushing(short)
89029Steering block bushing (long)
892064x10mm
bhcs
x2
89040Inner
hinge pin
x2
16:: Front Suspension Assembly - (cont.)
:: Front Suspension Assembly - (cont.)
:: Front Suspension Assembly - (cont.)
Side View
25215M3
locknut
Build right and left sides!
!
2 dot down
hinge pin bushingBuild right
and left sides!!
89039Hinge pin bushings(two dot,
down)
892283x40mm
shcs
89035Arm
mount(A)
x2
x2
x2
x2
x2
892183x8mmwasher
x2
x2x2892253x24mm
shcs
25215M3
locknut
89031Blue 1.7mmcaster spacer
x4
Side View
Build right
89017Swaybarmount
252253x3mmsetscrew
x2
315313x6mm
bhcs
892193x5mmsetscrew
890882.5mm anti roll
bar (silver)
x2
x2
#1596thread lock
Tighten screws to remove free play but
ensure some movement in the
anti-roll bar.
!!
892263x26mm
shcs
25215M3
locknut
17
:: Rear Gearbox Assembly
:: Front Suspension Assembly - (cont.)
892174x14mm
fhcs
89022Front
bumper
892144x12mm
fhcs
x2
x425204
3x16mmfhcs
25215M3
locknut
892215x4mmsetscrew
89571SC8.2e
center drive line input
cup
Key setscrew onto flat side of shaft.Tighten with no
endplay.
!
#15
96th
read
lock
89571SC8.2e
center drive line input
cup
252368x16mmbearing
89017Inner
gearbox
89114Diff pinion
gear
x2
x225215M3 locknut
#1596thread lock
18:: Rear Gearbox Assembly - (cont.)
:: Rear Gearbox Assembly - (cont.)
:: Rear Gearbox Assembly - (cont.)
89037Arm
mount (C)
89039Hinge pin bushing
(2 dot down)
892243x16mm
shcs
x2
x2 892183x8mmwasher
x2
2 dot down
hinge pin bushing
89258Chassis brace(rear)
892113x26mm
fhcs
25215M3
locknut
251923x20mm
shcs
251923x20mm
shcs
89473Steel shockstandoff
x2 x2
x2
892253x24mm
shcs
89011Body
mount and
spacer
892183x8mmwasher
892183x8mmwasher
25215M3
locknut
89587RC8.2e RTR shock tower
(rear)
x2
x2
x2
x2
#1596thread lock
894543x12mm
shcs
x2
19:: Rear Gearbox Assembly - (cont.)
:: Rear Suspension Assembly - (cont.)
Diff shims in-stalled to diff,
diff installed to gearbox.
!
:: Rear Suspension Assembly
Build right and left sides!
!
8916215x21mmbearing
89033hub
carrier(left, right)
252368x16mmbearing
89107Bearing shield 89221
5x4mmsetscrew
89572SC8.2e
dogbone axle
89251Wheel hex
89096Wheel hex
pins
#15
96th
read
lock
89551RC8.2
rear arm
251923x20mm
shcsDroop screw
placement!
!
!!
Build right and left sides!
!
!
89511Swaybar ball joint
89091Swaybar
joint
46713x10mmsetscrew
89511Swaybareyelet
Build Two!!
x2
892204x12mmsetscrew
892243x16mm
shcs 89017Outer
gearbox
x2
89117Diff shim
x2!
!89472Front
bulkhead spacer
:: Rear Suspension Assembly - (cont.)
:: Rear Suspension Assembly - (cont.)
:: Rear Suspension Assembly - (cont.)
20
315202.5x6mm
bhcs
89031Hub
spacers(red)
89041Outer
hinge pin
x2
Build right and left sides!
!
89575SC8.2e
dogbone (82mm)
x2
89038Arm
mount (D)
892012.5x3mm
bhcs
892782.5mmwasher
89040Inner
hinge pins
x2
x2
x2892283x40mm
shcs
x2
x2892183x8mmwasher
315313x6mm
bhcs
252253x3mmsetscrew
89017Swaybar mount
x2
x2
#1596thread lock
#1596thread lock
#1596thread lock
894743x22mm
shcs
25215M3
locknut
892193x5mmsetscrew
890892.8mm anti roll
bar (gold)
x2
Tighten screws to remove free play but
ensure some movement in the
anti-roll bar.
!!
:: Rear Suspension Assembly - (cont.)
:: Rear Suspension Assembly - (cont.)
21
892283x40mm
shcs
25215M3
locknut
x2
x2
x2
x2
25215M3
locknut
251923x20mm
shcs
25215M3
locknut
89540RC8.2
wing mount upper brace
89540RC8.2
wing mounts
89592RC8.2e
RTR wing(black)
892023x12mm
bhcs
892183x8mmwasher
x2
x2
22:: Rear Suspension Assembly - (cont.)
:: Center Bulkhead Assembly
895283x5.6mm
steel washer
894543x12mm
shcs
315323x8mm
bhcs
252234x3mmsetscrew
x2
x2
x2
89019Center
bulkhead(bottom)
89019Center
bulkhead(top)
#1596
threadlock
#1596threadlock
x2892053x26mm
bhcs89501Motor mount
Motor
89254Center diff top plate
895171/8
pinion(17T)
25215M3
locknut
892174x14mm
fhcs
892144x12mm
fhcs25204
3x16mmfhcs
x2
x2
23
:: Center Bulkhead Assembly - (cont.)
:: Center Bulkhead Assembly - (cont.)
89584RC8.2e RTR
dogbone (96mm, front)
89510Motor pad
89583RC8.2e RTR
dogbone (99mm, rear)
Install dog bones into center diff
outdrives!
!x489217
4x14mmfhcs
89502RC8e
center diff riser
#1596
thread lock
24:: Shocks Install
:: Shocks Install - (cont.)
:: Shocks Install - (cont.)
Note the direction of the shock cap
when installing onto shock standoffs
!
Install two front shocks.
!
After installation, adjust droop screw to get a front shock length of
103mm measured center to center on the shock cap / eyelet.
!
Install two rear shocks.
!Note the direction
of the shock cap when installing onto
shock standoffs
!
25612M3 locknut with flange
89083Shock
bushing
91069Shock mount
pin, steel
894543x12mm
shcs
25612M3 locknut with flange
89083Shock
bushing
25:: Shocks Install - (cont.)
:: Radio Tray Assembly
:: Radio Tray Assembly - (cont.)
After installation, adjust droop screw to get a rear shock length of
122mm measured center to center on the shock cap / eyelet.
!
251873x14mm
bhcs
89504Radio tray
(bottom)
x4
89006Servo
spacers
892183x8mmwasher
89506Hook and
loop battery straps
89505RC8e
battery tray
x3
x4
x4
Servo mounts vary per servo manufacturer.
Space your servos low to the chassis without touching the bottom.
!
Note: Attatch speed control with servo tape #6727.
Note: hook and loop straps are removed
for view clarity.
Note: route the speed control receiver wire through this
opening.
Note: route the speed control receiver wire through this
opening.
!
!
! !Speed control
Servo
91069Shock mount
pin, steel
894543x12mm
shcs
26:: Radio Tray Assembly - (cont.)
:: Radio Tray Assembly - (cont.)
:: Radio Tray Assembly - (cont.)
Note: hook and loop straps are removed
for view clarity.
!
89509Flywheel opening
cover
89507Battery
tray pads
BottomView
!Bottom
View
RC8TeSC8e
RC8TeSC8e
25215M3
locknut
89216M4
locknut
Front
x2
x2
89509Battery
tray postNote: hook and loop straps are removed
for view clarity.
Note: there are two different positions
for the locknuts depending on what
vehicle you have.
!
!
RC8.2eRC8.2e
892222.5x8mm
shcs
Front
x4
Note: hook and loop straps are removed
for view clarity.
Note: the cutout on the battery tray bridge is facing the
battery tray!
!
!RC8.2e
RC8.2e
RC8TeSC8e
RC8TeSC8e
27:: Radio Tray Assembly - (cont.)
:: Radio Tray Assembly - (cont.)
:: Radio Tray Assembly - (cont.)
315313x6mm
bhcs
21173Small
body clip
89504Radio tray
(top)
892193x5mmsetscrew 6338
Antenna tube and
cap
x2
x2
Note: route the speed control receiver wire up
and over the bridge
Note: route the speed control receiver wire through the radio box
hole.
Note: route the servo wire to the receiver
through this opening.
Note: plug in your speed control and
servo to your receiver.
Note: route your receiver’s antenna wire through the slot in the radio tray, and
through your antenna tube.
Note: transponder not included.
Note: hook and loop straps are removed
for view clarity.
Note: hook and loop straps are removed
for view clarity.
Note: hook and loop straps are removed
for view clarity.
! ! !
! !
!
!
!
!
Receiver
28:: Radio Tray Assembly - (cont.)
:: Radio Tray Assembly - (cont.)
Enlarge holes in servo horn!
!
A - AirtronicsF - FutabaH - HitecJ - JR
Printed here
!
23083x18mm
bhcs
252013x8mm
fhcs
89007Servo
horn ring
89007Steering
servo horn
89007Servo cone
washer
#1596
thread lock
25215M3
locknut
Note: hook and loop straps are removed
for view clarity.
!
29
:: Radio Tray Assembly - (cont.)
:: Radio Tray Assembly - (cont.)
892053x26mm
bhcs
25215M3
locknut
892134x6mm
fhcs
892113x26mm
fhcs
x2
x2
892144x12mm
fhcs
x2
252033x12mm
fhcs
x3
:: Radio Tray Assembly - (cont.)
30
:: Wheels, Tires, and Body Install
Tires:When gluing tires to wheels, use a fast-curing Tire glue (CA) (AE Pt#1597). This is available at your local hobby shop. Make sure to clean the mounting surface of the tire with alchohol for best adhesion.
Tires:
#1597
CA tire glue
Build four wheels/
tires
!
Note: hook and loop straps are removed
for view clarity.
Note: Install wire tie as shown.
!
!!
!
Note: batteries not included.
!
89255RTR Pre-glued
wheel/tire
89255RTR Pre-glued
wheel/tire
x4
x4
3719Nylon wire
tie (6” )
31
:: Wheels, Tires, and Body Install (cont.)
:: Wheels, Tires, and Body Install
89252Wheel hex
nuts (silver)
x4
2208Large hood pins
x2
315313x6mm
bhcs
89523RC8e
body, clear
32:: Chassis Tips
:: Front End Tips
Gearing:Follow your motor manufacturer’s recommendations for gearing options.
Gear Mesh:To correctly set your gear mesh, follow the steps below:1. Loosen the set screw on the motor’s pinion gear. The set screw can be accessed through the slot on the side of the motor mount slide, opposite the spur gear. Slide the pinion on the motor shaft until the gear face of the pinion is entirely aligned with the gear face of the spur gear (see diagram). Tighten the set screw while ensuring it is aligned with the flat face on the motor shaft.
2. Loosen the two motor screws until the motor is able to move freely. Slide the motor as far as it can go towards the spur gear, ensuring that the teeth of the pinion and the spur gear are interlocking. Back the motor off a tiny bit (approximately 0.5 mm), and tighten the screws that lock the motor in place. Proper gear mesh has been achieved when the teeth are meshing closely, but the gears still have a small amount of play between them. If you hold one gear, you should be able to rock the other gear back and forth a small amount. If there is not “free play”, your gear mesh is too tight and you should back off the motor a little farther.
Differential Fluid:Team Associated includes a complete bottle of 5,000cst diff oil. You can also provide your own oil and try one of the optional setups.Standard differential fluid setup: Front = 5,000cst; Center = 5,000cst; Rear = 5,000cst.Optional diff setup 1 (high grip track): Front = 5,000cst; Center = 10,000cst; Rear = 5,000cst.
Center Differential: Use the standard setup for most cases. Some racers will try thicker oil (7,000-10,000cst) when greater acceleration is needed. This is typically done on very smooth tracks since thicker fluid can reduce handling in bumpy conditions.
Front Differential: Use the standard setup for most cases. Try 7,000cst to 10,000cst to get less low speed steering and better acceleration out of turns.
Kickup Bushing:Generally more kick-up will provide better handling in the bumps and have better straight line acceleration.Less kick-up will provide more all around steering and have a more aggressive feel.
Caster:The standard caster block insert setup is for 16 degrees. The standard inboard kick-up is 9 degrees (2-dot up insert in A-plate). You can reduce the caster using 14 degree inserts (also move both upper cone washers in front of the ball joint) for smoother steering. Changing to 18 degree inserts (also move both upper cone washers behind the ball joint) will typically provide more steering on power but reduce handling in bumpy conditions.
Front Upper Pivot Insert:The standard setup is to use 2-dot up in the tower and 1-dot in the top plate. It is recommended to maintain a 1 dot gap (1mm per dot) front to rear when using 2-dot up in the A-Plate. Reducing the A-Plate insert to 1-dot allows the use of same dot number insert in both tower and top plate. Going up to 3-dot up in the tower will give more turn in, but less steering on power/exit. Going down (1-dot, 2-dot down) will reduce turn in, but give more steering on exit.
Front Camber Link-Outer:The standard short location will work the best for most tracks. Going to the long front link will give you more steering, but can make the car less predictable in bumps and exiting turns.
Pinion
Spur Gear
PinionSpur Gear
33
:: Rear End TipsRear Differential: Start with the standard setup. For expert drivers, the most popular setting is 3,000 cst. The thicker 5,000cst kit oil will rotate less in the turns and accelerate straight on power. The thinner oil (2,000 or 3,000cst) will give more low speed traction.
Anti-squat: Anti-squat denotes the angel of the rear inner hinge pin relative to the ground. This setting is adjusted by changing the insert bushing in the C-Plate. The kit setting is 2 degrees (2-dot down) but you change to 1 degree (3-dot down). Typically less anti-squat lets the suspension work more over the bumps, but it will sacrifice the ability to square up on power.
Rear Camber Link Length & Vertical Adjustment:You can change the length of the camber link on the hub or tower as well as adjust the vertical location on the tower. A longer link will give the feeling of the most grip, but it will not be as responsive to square up on throttle, and might get loose if driven hard. This can easily be corrected by running the shorter link on the hub, but it will sacrifice some forward grip.
Changing to a higher location on the tower will be a smaller adjustment than changing the length of the upper link. Going up on the tower location has a similar effect as a longer camber link, but not as drastic. For example, if you change to the short rear link on the hub and you need to gain more forward grip, try raising the link up on the tower. New additional lower holes should be used when running the optional hinge pin hole in the rear hub carrier.
Rear Hub Hinge Pin Height:The upper hole gives more rear grip on turn in, and good forward traction, but it might have difficulty squaring up out of turns. The lower hinge pin hole in the hub will be more responsive on throttle, and give more side grip in the turns.
Rear Hub Spacing:You have 3 options for rear hub spacing, FWD, MIDDLE, & BACK. The kit setting provides a good balance of rear traction and steering, and will be used most often. Moving the hubs FWD will give more rear traction for low grip tracks. You can use the hubs BACK on high grip tracks for more on-power steering. Also, you can replace the included shims to get intermediate settings.
Rear Camber:A good starting camber setting is –2 degrees. Use the included #1719 camber gauge to set your camber. Adding a small amount of positive camber, where the top of the tire is leaning out, will tend to improve straight-line acceleration on loose tracks.
Rear Ride Height:The rear ride height setting you should use most often is 29mm of gap between the chassis bottom and ground. Check the ride height with the FT Ride Height Gauge (#1449) by lifting up the entire vehicle about 8-12 inches off the bench and drop it. After the suspension “settles” into place, then raise or lower the ride height with the shock clips as necessary and recheck.
Rear Arm Shock Location:Inside on the arm will give less entry steering, accelerates better straightline through bumps, but may lack side bite. Outside on the arm will be less grip, more steering, but will be more predictable when it breaks traction.
:: Front End Tips (cont.)Front Camber Angle:A good starting camber setting is –2 degrees. Positive camber, where the top of the tire is leaning out, is typically not recommended.
Front Toe-In:Zero degree toe-in (tires pointing straight forward) is a good starting setting. You can increase turn in by adding 1-2 degrees of toe-out (front of tires point slightly out). Front toe - in is not a typical tuning adjustment used by the Team.
Front Ride Height:The front ride height setting you should use most often is with 29mm of gap between the chassis bottom and the ground. Check the ride height with the FT Ride Height Gauge (#1449) by lifting up the entire vehicle about 8-12 inches off the bench and drop it. After the suspension “settles” into place, then raise or lower the ride height with the shock clips as necessary and recheck.
Front Arm Shock Location:Inside on the arm will give a more responsive front end. Outside on the arm will be less responsive steering, but will be more predictable through bumps.
34:: Droop Settings (Buggy shown but applicable for all vehicles)
Step 1: With only the bottom of the shocks attatched, the droop screws raised all the way, and the chassis above your working surface so the arms are at full extension, you should be able to easily slide the top of your shock over the standoff screw, while leaving the shock at full extension. If the mounting hole of the shock cap is above or below the standoff screw, adjust the droop screw accordingly. Repeat for all corners of your vehicle. Measure from the center of the standoff screw to the center of the shock riser button to get your FULL DROOP setting.The front shocks should be 102mm, while the rear shocks should be 120mm.
Note: Rear hub spacing is not recommended with RTR dog bones. For more adjustability, use CVA’s in place of dog bones.
Step 2: Finish installing the shock to the standoff. Set your vehicle to your desired droop setting. To increase your droop turn the droop screw (from the top) counter-clockwise (loosen), turn the droop screw (from the top) clockwise (tighten) to decrease your droop. Remember, never back the screw out beyond full droop or you could risk damage to your vehicle.
Step 3: Measure from the center of the shock standoff screw to the center of the shock riser button to get your final droop setting. The front shocks should both be set at the same lenght, as should the rearshocks. * The normal droop setting is between 0-5mm from the FULL DROOP measurement.
Front Droop: Increasing front droop (loosen droop screws) will increase off-throttle steering. It also allows the front end to lift more, giving more rear grip and less front grip on-power. Remember to never loosen the screws beyond the FULL DROOP setting. Decreasing front droop (tighten droop screws) yields more on-power steering and quicker response at the expense of some stability in bumpy sections. It will also give less off-throttle steering.
Rear Droop: Increasing rear droop (loosen droop screws) will increase traction in bumpy sections, but will reduce high-speed stability. Remember to never loosen the screws beyond the FULL DROOP setting. Decreasing rear droop (tighten droop screws) will increase stability in high speed sections, but will reduce stability in bumpy sections.
Setup Sheets:Most often the best way to get your car handling right is to go to our website www.rc10.com and click on the “Setup Sheets” link, then the link to your vehicle, then search for your vehicle. Our team of professional drivers help develop these setups at National events. Also, most drivers have a “base” setup that they use as a starting point for ev-ery event. Try running some of our base setups OR look for track conditions and tires that are similar to your local track and mimic that setup. Remember, each adjustment has a purpose, so copy everything from the setup sheet and then make adjustments based on the recommendations in here at http://www.rc10.com/rc/tuning.
35:: Shocks
:: Springs
:: Front and Rear Gear Differential
:: Center Gear Differential
256128906589066890678908389215892608926189278893358935189352893538935489396895568958089582
8929289293892948929589347893488934989350
252368911389115891168911789120
891218920889496
252368910989110891158911689120
891218920889496895198952089521
211481
1102
211141
1102111
204814102220281841122
Pr.Pr.Pr.1
Pr.Pr.Pr.1
M3 Locknut With FlangeShock Rod EndShock O-RingsShock Limiters, SetShock BushingsPiston Locknut29mm RTR Shock Shaft, Front38mm RTR Shock Shaft, Rear2.5mm Washer16mm Shock Caps16mm Shock Bladders16mm Shock Rebuild Kit16mm Shock Pistons16mm Shock Spring Cups16mm RTR Pre-load Clips, Shock Collar SetRC8.2 Shock Boot Set16x29mm Shock Body RTR, Blue16x38mm Shock Body RTR, Blue
16x29mm front spring black (3.3lbs)16x29mm front spring silver (3.9lbs) - Kit16x29mm front spring bronze (4.7lbs)16x29mm front spring complete set16x38mm rear spring black (2.7 lbs)16x38mm rear spring silver (3.3 lbs) - Kit16x38mm rear spring bronze (4.0 lbs)16x38mm rear spring complete set
8x16x5 BearingsDiff Ring Gear, Includes Diff GasketDiff HousingDiff GasketDiff ShimsDiff Sun/Planet Gears, IncludesWashers and Pins, SetDiff 0-Rings, Big and Small, Set3x14mm FHCSDiff Outdrive, 16mm
8x16x5 BearingsSpur Gear 44T, Includes Diff Gasket - metalSpur Gear 46T, Includes Diff Gasket - metalDiff HousingDiff GasketDiff Sun/Planet Gears, IncludesWashers and Pins, SetDiff 0-Rings, Big and Small, Set3x14mm FHCSDiff Outdrive, 16mmPlastic Spur Gear 46T, Includes Diff Gasket - KitPlastic Spur Gear 48T, Includes Diff GasketPlastic Spur Gear 50T, Includes Diff Gasket
89354
89278
8921589351
89352
8906689352
89352
25612
89396
89396
89335
89083 25236
89115
89121
89121
89116
89120
89120
89121
89120
89121
89208
89208
25236
89113
89353
89353
89065
89065
Front89260
Rear89261
Front89293
Rear89348
Front89580
Rear89582
Frontand Rear
89556
89496
89496
89120
89519
25236
89115
89121
89120
89121 89121
89116
89120
89121
89496
89496
89208
89208
25236
89351
89352
8906689352
89352
25612 89335
Front89580
Rear89582
Frontand Rear
89556
36:: Top Plate:: Shock Fluid
:: Steering
22082520225203252158901089011890398921489226892348923689455
6202020111
101011
10
Large Hood Pins3x10mm FHCS3x12mm FHCSM3 LocknutTop Plate - KitBody Mount SetHinge Pin Bushings, 1/2/3 dot, Set4x12mm FHCS3x26mm SHCSBlue Aluminum Top Plate (FT)Black Aluminum Top Plate (FT)3x22mm FHCS
5420542154225423542454255426542754285429543054315432543354345435543654375438
25204252153140489013890148901589016890758911789161892148921889272
2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.
20202221148110101
10 Weight Silicone Shock Fluid20 Weight Silicone Shock Fluid30 Weight Silicone Shock Fluid40 Weight Silicone Shock Fluid22.5 Weight Silicone Shock Fluid80 Weight Silicone Shock Fluid27.5 Weight Silicone Shock Fluid15 Weight Silicone Shock Fluid25 Weight Silicone Shock Fluid35 Weight Silicone Shock Fluid45 Weight Silicone Shock Fluid55 Weight Silicone Shock Fluid32.5 Weight Silicone Shock Fluid37.5 Weight Silicone Shock Fluid42.5 Weight Silicone Shock Fluid50 Weight Silicone Shock Fluid60 Weight Silicone Shock Fluid70 Weight Silicone Shock Fluid47.5 Weight Silicone Shock Fluid
3x16mm FHCSM3 Locknut6x10mm BearingSteering PostsSteering Rack PostServo Saver, SetServo Saver Bolt, Nut, Spring, SetSteering BallstudsDiff ShimsSteering Bearing Set4x12mm FHCS3x8mm WasherRTR Steering Rack
:: Lubes & Adhesives / Decals / Misc.11051596159754505451545254535454545554565457545854596588659166366727
716717381638203834
11111111111111112
11112
FT Green Slime Shock LubeFT Locking AdhesiveFT Tire Adhesive, MediumSilicone Diff Fluid 1000cstSilicone Diff Fluid 2000cstSilicone Diff Fluid 3000cstSilicone Diff Fluid 5000cstSilicone Diff Fluid 7000cstSilicone Diff Fluid 10000cstSilicone Diff Fluid 20000cstSilicone Diff Fluid 30000cstSilicone Diff Fluid 60000cstSilicone Diff Fluid 100000cstBlack Grease - 4ccS.Diff Lube - 4ccSilicone Grease - 4ccServo Tape
Reedy 2009 Sticker SetReedy Powered Logo DecalAmerican Bumper StickerAE Logo Decal SheetAE Blue Embossed Logo Sticker
25215
25215
25215
89272
25204
25204
89075
8907589218
89218
25215
8921489214
89013
89013
31404
31404
3140489014
89161
89161
89161
89117
8911789016
89161
89015
89015
89015
89016
89016
89014
31404
8921489214
25215
25215 25215
2520325202
25202
25203
89010
89010
2208
89011
89455
89226
89039
89039
37:: Front Gearbox
:: Front Suspension
25215252363153189017890358903689040890398911489201892148921789218892198922189224892268922889278894728957189584
202
10111111
10101010101010101020221
25192252152523631520890288902989031890328904089041890748907589076890968910289105891628920689207892208922189225892518925289268892698945489549895508955889573
91069
202026
Pr.111114414212
1010101010Pr.222
10Pr.Pr.Pr.2
4
M3 Locknut8x16x5 Bearing3x6mm BHCSFR/RR GearboxArm Mount AArm Mount BInner Hinge Pin, SetHinge Pin Bushings, SetDiff Pinion Gear2.5x3mm BHCS4x12mm FHCS4x14mm FHCS3x8mm Washer3x5mm Setscrew5x4mm Setscrew3x16mm SHCS3x26mm SHCS3x40mm SHCS2.5mm WasherRC8B Front Bulkhead SpacerSC8.2e Center Drive Line Input RC8.2e RTR Dogbone 96mm
3x20mm SHCSM3 Locknut8x16x5 Bearing2.5x6mm BHCSSteering BlocksSteering Block Bushings, SetCaster/Hub Spacers, SetCaster Angle Bushings, SetRC8 Inner Hinge Pins, SetRC8 Outer Hinge Pins, SetSteering Rod EndsRC8 Steering BallstudsRC8 Camber Rod Ends, SetRC8 Wheel Hex PinsRC8 Front/Rear CVA BoneRC8 CVA Rebuild FR/RR, Set15x21x4 Bearing4x10mm BHCS4x12mm BHCS4x12mm Setscrew5x4mm Setscrew3x24mm SHCSWheel Hex DriveWheel Hex Nut, silverSteel Turnbuckle, 42mmSteel Turnbuckle, 38mm 3x12mm SHCSRC8.2 Front Upper ArmsRC8.2 Front ArmsRC8.2 Caster BlocksSC8.2e Light Weight CV Axle, SteelShock Mount Pin, Steel
89217
89219
89219
89017
89017
89017
25215
25215
25215
25236
25236
89571
8958489221
89221
89114
89472
8922489226
89214
8922489218
89218
89218
89035
89218
89228
89201
89201
89278
8927889036
31531
89039
89040
8904089039
91069
8945489220
25215
2521589031
89207
89206
89549
31520 89041
89032
89032
89029
89029
8902889075
8907589252
89251
89096
25236
89550
89102
89105
89162
89040
8926989076
89074
89074 89268
89558
89225
89573
25192
38:: Rear Gearbox
:: Rear Suspension
25215252363153189017890378903889039890408911489201892118921489217892188921989221892248927889279894728957189583
2026111111
10101010101010102010221
25192252152523631520890318903389041890768909689107891628922089221892518925289269894548947489551895728957591069
2020261
Pr.11412
1010Pr.22
1010Pr.224
M3 Locknut8x16x5 Bearing3x6mm BHCSRC8 FR/RR Gearbox, SetArm Mount CArm Mount DRC8 Hinge Pin Bushings, SetInner Hinge Pin, SetRC8 Diff Pinion Gear2.5x3mm BHCS3x26mm FHCS4x12mm FHCS4x14mm FHCS3x8mm Washer3x5mm Setscrew5x4mm Setscrew3x16mm SHCS2.5mm Washer3x45mm SHCSRC8B Front Bulkhead SpacerSC8.2e Center Drive Line Input CupRC8.2e RTR Dogbone 99mm
3x20mm SHCSM3 Locknut8x16x5 Bearings2.5x6mm BHCSRC8 Caster/Hub Spacers, SetRC8 Hub CarriersRC8 Outer Hinge Pins, SetRC8 Camber Rod Ends, SetRC8 Wheel Hex PinsRC8 Rear CVA Shield/Boot, Set15x21x4 Bearing4x12mm Setscrew5x4mm SHCSWheel Hex DriveWheel Hex Nut, silver38mm Steel Turnbuckle3x12mm SHCS3x22mm SHCSRC8.2 Rear ArmsSC8.2e Dog Bone AxleSC8.2e RTR Dogbone 82mmShock Mount Pin, Steel
89017
89211 89017
2521525215
25236
25236
89571
89583
89221
89221
89114
89472
89220
89076
89214
89039
89039
89278
89278
89201
89201 89279
89218
89218
89038
89037
89218
89224
89040
89040
89217
89224
31531
31531
89219
89076
8907689076
89269
25192
89454
89551
89572
89575
8910789162
89474
25215
89031
25236
89033
89096
89251
89252
91069
31520
89041
39:: Front Shock Tower :: Rear Shock Tower
:: Center Bulkhead
890398920289218892258947389586
2519225215890118921889225894548947389587
25223315328901989205892178925489454895018950289512895138951489515895168951789528
110101041
20201
10101041
206110101101111111110
Hinge Pin Bushings, 1/2/3dot Set3x12mm BHCS3x8mm Washer3x24mm SHCSRC8B Steel Shock Stand-offsRC8.2e RTR Front Shock Tower
3x20mm SHCSM3 LocknutBody Mount Set3x8mm Washer3x24mm SHCS3x12mm SHCSRC8 Steel Shock StandoffsRC8.2e RTR Rear Shock Tower
4x3mm Setscrew (for use with pinions)3x8mm BHCSRC8 Center Bulkhead, Set3x26mm BHCS4x14mm FHCSCenter Top Plate3x12mm SHCSMotor Mount/BulkheadCenter Diff RiserRC8e 12T PinionRC8e 13T PinionRC8e 14T PinionRC8e 15T PinionRC8e 16T PinionRC8e 17T Pinion - Kit3x5.6x0.5mm Washer, Steel
89502
8901989517 89454
89528
2522389019
89254
31532
89205
89217
89217
89501
89225
89225
89218
89218
89218
89218
89218
89225
89225
89218
89039 25215
25215
25192
25192
25192
89454
8958789473
8947389473
89473
89011
89202
89202
89586
:: Chassis Braces2520425215890688906989077
892388923989258
2020111
111
M3x16mm FHCSM3 LocknutRC8 Pivot Chassis Brace Set (Front)RC8 Pivot Chassis Brace Set (Rear)Chassis Brace Rod Ends, Set works with #89068, 89069FT Aluminum Chassis Brace (Front)FT Aluminum Chassis Brace (Rear)RC8 Chassis Braces, Plastic - Kit(Front, Rear)
RearRear
Front
89258
89258
2520425204
25215
25215
40:: Radio Tray
230863382117325187252012520325215315318900689007890788920589211892138921489216892188921989222892678950489505895068950789509
61
12202020206111
1010101010101010211111
3x18mm BHCSAntenna Tube and Cap18T Body Clips3x14mm BHCS3x8mm FHCS3x12mm FHCSM3 Locknut3x6mm BHCSRC8 Servo Mount Spacers, SetSteering Servo Horns, SetRC8 Servo Link Rod Ends, Set3x26mm BHCS3x26mm FHCS4x6mm FHCS4x12mm FHCSM4 Locknut3x8mm Washer3x5mm Setscrew2.5x8mm SHCSSteel Turnbuckle, 32mmRC8e Radio TrayRC8e Battery TrayHook and Loop Battery Straps, SetBattery Tray Pads, SetBattery Tray Accessories, Set
:: Chassis
89506
25215
25215
89078
89205
89078
89267
89007
89007
89007
25201
89078
2308
89078
89509
89504
21173
21173
89222
31531
6338
6338
89219
25203
2520325203
89006
89006
8921889218
25187
25187
89504
89507
25215
89216
89216
89505
89509
8921189214
89213
89509
2520189022894768951089552
201111
3x8mm FHCSFront BumperFT RC8B +3mm ChassisMotor PadRC8.2 Side Guards, Set 89552
89552
25201
25201
25201
25201
89510
89022
89476
41:: Anti-Swaybars
46712522589086890878908889089890918909389511
6201111411
3x10mm Setscrew3x3mm SetscrewFT Antiroll Bar SetFT Antiroll Bar Black, 2.2mmFT Antiroll Bar Silver, 2.5mm - Kit (rear)FT Antiroll Bar Gold, 2.8mm - Kit (front)FT Antiroll Bar Socket JointFT Antiroll Bar Black, 3.0mmRC8.2e RTR Swaybar Link Set
89087890888908989093
8909189511
89511
4671
89511
25225
:: Wing
:: Wheels / Tires
:: Body / Decals
2519225204252158920289218892288954089592
8915289153892558929689297
17372208315318927789475895088952389559895898959089591
20202010101011
44
Pr.44
16611111111
3x20mm SHCS3x16mm FHCSM3 Locknut, (Black)3x12mm BHCS3x8mm Washer3x40mm SHCSRC8.2 Wing Mount, SetRC8.2e RTR Wing, (Black)
RC8 81mm Wheels (White) - Kit RC8 81mm Wheels (Yellow)RTR Pre-Glued Wheel/Tire (White)RC8 83mm Wheels (White)RC8 83mm Wheels (Yellow)
FT Body ScissorsLarge Hood Pins3x6mm BHCSRC8 RTR Body Wrap DecalsRC8B Decal SheetRC8.2e FT Decal SheetRC8e Body w/Window Masks (Clear)RC8.2 Decal SheetRC8.2e RTR Decal SheetRC8.2e RTR Body (Blue)RC8.2e RTR Body (Red)
89255
89523
31531
2208
2208
89592
89218
89218
89202
89202
89540
89540
8954089228 25215
25215
2521525215
25215
25192
42:: Factory Team and Option Parts :: Factory Team and Option Parts - (cont.)25392315508093089005890128901689020890458905389054890708907189073890828909489095891608916189229892348923589236892378928489285892868929089291
893208932189344
89346893558937889379893808938189405894068945689460894618946289463894668946789468894698947089473894778947889481894828948589487894888948989490894928949489529895308953189532895338953489535895368953789541
895428954389544895458954689547895488955389554895558955689557895588956191069
10611111122121422111011112221
Pr.
11
Pr.
1211
Pr.Pr.4441111111112221221111411111111441
22212222
Pr.Pr.12
Pr.Pr.4
3mm Blue Locknut, FlangedM3 Aluminum Lock Nut1/8 Scale Electric Conversion KitAluminum Antenna MountRC8 Steering Rack, Carbon FiberServo Saver Bolt, Nut, SpringCenter Bulkhead Plate CFRC8 FT 0.5 Degree Toe BushingGold Shock Shaft 29mmGold Shock Shaft 38mmRC8 Ti Turnbuckle SetCamber Turnbuckles 5mmServo Turnbuckle 4mmRC8 Shock Standoffs, AluminumNyloc Wheel Hex Nuts, BlueWheel Hex, AluminumDrivetrain Bearing, SetSteering Bearing SetBlue Countersunk WasherBlue Aluminum Top Plate (FT)RC8 CNC Aluminum Steering RackBlack Aluminum Top Plate (FT)RC8 Skid PlateRC8 Rear Stub Axle (Aluminum)RC8 Front Stub Axle (Aluminum)RC8 Gearbox Input Cup (Aluminum)FT 16x29mm Front Shock KitFT 16x29mm Front Shock Bodies, Hard Coated & Threaded - requires #89555 shock shaftsRC8T Front Chassis Brace SetRC8T Rear Chassis Brace SetFT 16x38mm Rear Shock Bodies, Hard Coated & Threaded - requires #89555 shock shaftsFT 16x38mm Rear Shock Kit16mm Shock Collar, threadedFT RC8T Aluminum Chassis Brace, FrontFT RC8T Aluminum Chassis Brace, RearRC8 FT Machined Steering BlocksRC8 FT Machined Rear HubsNyloc Wheel Nuts (Silver)Nyloc Wheel Nuts (Black)16mm Piston 10x1.1RC8 Aluminum A-PlateRC8 Aluminum B-Plate w/Pins, SetRC8 Aluminum C-PlateRC8 Aluminum D-Plate w/Pins, SetRC8B Inner Hinge Pins, 4mm HMA, SetHD Shock Shaft, 4x29mmHD Shock Shaft, 4x38mmHD Shock Ends, SetRC8B Shock Tower Hinge Pin Bushings, SetSteel Shock StandoffFT RC8B Light Outdrive, FrontFT RC8B Light Outdrive, Rear FT RC8B Low B-PlateFT RC8B Low B-Plate InsertsFT RC8B Aluminum Steering PostsRC8.2 FT Rear Swaybar, 2.5 GreenRC8.2 FT Rear Swaybar, 2.6 WhiteRC8.2 FT Rear Swaybar, 2.7 BlueRC8.2 FT Rear Swaybar, 2.8 Yellow16mm Piston 5x1.1 + 5x1.2RC8B Light Diff Ring Gear, Includes Diff GasketRC8.2e FT Motor Mount SetRC8.2 FT Front Swaybar KitRC8.2 FT Rear Swaybar KitRC8.2 FT Front Swaybar, 2.2 GreenRC8.2 FT Front Swaybar, 2.3 WhiteRC8.2 FT Front Swaybar, 2.4 BlueRC8.2 FT Front Swaybar, 2.5 YellowRC8.2 Swaybar Pivot Ball w/setscrewsRC8.2 Swaybar Drop Link w/pivotsFT RC8.2 Front Spring Kit
FT RC8.2 Front Spring, 4.00 GreenFT RC8.2 Front Spring, 4.30 SilverFT RC8.2 Front Spring, 4.65 BlueFT RC8.2 Rear Spring KitFT RC8.2 Rear Spring, 3.25 GreenFT RC8.2 Rear Spring, 3.55 SilverFT RC8.2 Rear Spring, 3.75 BlueRC8.2 Front Hinge Pin, TiNHD Shock Shaft, 4x26mmHD Shock Shaft, 4x36mmRC8.2 Shock Boots, Front & RearPin Reatainer O-Ring and BootRC8.2 Caster Blocks, Left & RightRC8.2 Mud Guards, Left & RightShock Mount Pin, Steel
:: XP Electronics291262914529166291672920929210292112921229217292182922129222
111111111111
S2008MG ServoXP SC1300-BL Brushless ESCXP DS1313 Digital ServoXP DS1015 Digital ServoGear Set, DS1313Gear Set, DS1015Servo Case , DS1313/DS1015Accessory Pack, DS1313/DS1015TRS402SSi 2.4GHz 4Ch ReceiverXP2-SSi 2.4GHz Radio SystemXP3-SS 2.4GHz Radio SystemTRS401SS 2.4GHz 4Ch Receiver
:: LRP Chargers, Soldering IronsLRP41281LRP41555LRP42103LRP42104LRP42105LRP42305LRP43200LRP45200LRP65800LRP65802LRP65803LRP65804
111111111111
Quadra Pro 2 ChargerPulsar Touch Competition ChargerLiPo Balance Board XHLiPo Balance Board FP/TP LiPo Balance Board PQPulsar Touch Temperature SensorLRP Competition 20A Power SupplyLiPo Parallel BalancerHigh Power Solder StationSoldering Tip 5mmSoldering Tip 1.2mmSoldering Handle
:: LRP 1/8 Brushless SystemsLRP53230LRP53235LRP53240LRP80786LRP80787LRP80788LRP80880
1111111
Dynamic 8 Brushless Motor 1800KVDynamic 8 Brushless Motor 2000KVDynamic 8 Brushless Motor 2200KVIX8/Dynamic 8 2200KVIX8/Dynamic 8 1800KVIX8/Dynamic 8 2000KVIX8 Brushless ESC
43
:: Reedy Batteries
:: Reedy Accessories
302303626632633634637733
654655656657658659716978979980981982
SP35MSP35L
SP35XLSP35XXL
SP35XXXLSP36MSP36L
SP36XLSP36XXL
SP36XXXLSP37SSP37MSP37L
SP37XLSP37XXLSP37XXL
SP38SP39SP418
11111111
1111111111111111111111111111111
AA Alkaline 1.5V (4)AA 2700mAh NiMH 1.2V Rechargeable LiPo 60C 5500mAh 14.8V TX Lightweight Battery 1350mAh 11.1VTX Battery - 3PK, M11 3000mAh 11.1VTX Battery - Helios, Z1 2400mAh 11.1VTX Battery - M11X 2500mAh 7.4VWolfpack LiPo 3700mAh 14.8V 35C w/DEANS®
4.0mm plugs (2M, 2F) 4.0mm plugs (2M, 10F) 4.0mm plugs (10F)4.0mm plugs (100F)4.0mm plugs (10M)4.0mm plugs (30M)Reedy 09 Decal SetFlat Sensor Wire 70mmFlat Sensor Wire 110mmFlat Sensor Wire 150mmFlat Sensor Wire 200mmFlat Sensor Wire 270mmReedy Logo T-Shirt - White MReedy Logo T-Shirt - White LReedy Logo T-Shirt - White XLReedy Logo T-Shirt - White XXLReedy Logo T-Shirt - White XXXLReedy Logo T-Shirt - Black MReedy Logo T-Shirt - Black LReedy Logo T-Shirt - Black XLReedy Logo T-Shirt - Black XXLReedy Logo T-Shirt - Black XXXLReedy 2012 T-shirt - Black SReedy 2012 T-shirt - Black MReedy 2012 T-shirt - Black LReedy 2012 T-shirt - Black XLReedy 2012 T-shirt - Black XXLReedy 2012 T-shirt - Black XXLReedy Trucker HatReedy PatchFactory Team Car Carrier Bag
:: ApparelSP35**SP36**SP62**SP63**SP64**SP65**SP66**SP67**SP69**
SP70**SP71**SP411SSP411LSP413SSP413LSP416SP417
SP420**715
110684
111111111
11111111
Pr.11
Reedy 09’ White T-Shirt (M, L, XL, 2XL, 3XL)Reedy 09’ Black T-Shirt (M, L, XL, 2XL, 3XL)AE Vertigo Long Sleeve T-Shirt (S, M, L, XL, 2XL)AE Vertigo White T-Shirt (S, M, L, XL, 2XL, 3XL, 4XL)AE Vertigo Blue T-Shirt (S, M, L, XL, 2XL, 3XL, 4XL)AE Vertigo Black T-Shirt (S, M, L, XL, 2XL, 3XL, 4XL)AE Stencil Blue T-Shirt (S, M, L, XL, 2XL, 3XL, 4XL)AE Stencil Gray Sweatshirt (S, M, L, XL, 2XL, 3XL)AE 26 Time World Championship T-Shirt, Black (S, M, L, XL, 2XL, 3XL)Associated Windbreaker (S, M, L, XL, 2XL, 3XL)Associated Winter Jacket (S, M, L, XL, 2XL) AE Hat 11’ Flatbill Black S/MAE Hat 11’ Flatbill Black L/XL26 Time World Championship Hat S/M26 Time World Championship Hat L/XL1/10 Car Carrier Bag Only1/10 FT Motor BagAE Pit Gloves (M, L, XL)Reedy 2009 Track BannerTeam Associated Track Banner
:: 1/18 Kits and RTR’s
:: 1/12, 1/10 Kits and RTR’s
2010320104201082011020115201182012120130
204240207023702970307032703470377046704770487049708070927093802080219039904090613010130107301119000490005900069000790010
11111111
1111111111111111111111111111
RC18B2 - RC18T2 Team KitRC18T2 Brushless RTR (ready-to-run)RC18B2 Brushless RTR (ready-to-run)RC18MT RTR (ready-to-run)RC18R Kamino RTR (ready-to-run)RC18R Niteline RTR (ready-to-run)SC18 Brushless RTR (ready-to-run)RC18LM RTR (ready-to-run)
Nitro TC3 RTR Plus (ready-to-run)FT 12R5.2 KitRC10T4.1 FT KitSC10 Associated/RC10.com Truck RTR (ready-to-run)SC10 KMC Wheels Race Truck RTR (ready-to-run)SC10 Ready Lift RTR (ready-to-run)SC10 FT KitRC10T4.1 RTR 2.4GHz Brushless (ready-to-run)SC10 RS RTR, 2.4ghz Brushless Lucas Oil BodySC10 RS RTR, 2.4ghz Brushless Monster Energy BodySC10 RS RTR, 2.4ghz Brushless Pro Comp BodySC10 RS RTR, 2.4ghz Brushless Rockstar/Makita BodyFT GT2 Nitro Truck KitGT2 RS Truck Nitro RTR (ready-to-run)SC10 GT Nitro RTR (ready-to-run)FT RC10R5 KitFT RC10R5-OVAL KitRC10B4.1 RTR 2.4GHz Brushless (ready-to-run)RC10B4.1 Worlds KitFT B44.1 4WD Buggy KitTC4 Club RacerFT TC6.1 4WD Touring Car KitTC4 4WD Touring Car RTR (ready-to-run)SC10 4x4 KitSC10 4x4 Lucas Oil RTR (ready-to-run)SC10 4x4 Pro Comp RTR (ready-to-run)SC10 4x4 Rockstar/Makita RTR (ready-to-run)SC10 4x4 FT Kit
:: 1/8 Kits and RTR’s20503
20504
8090580906809078091280933
80934
1
1
11111
1
Limited Edition MGT 4.60 Nitro RTR, w/flag body (ready-to-run)Limited Edition MGT 8.0 Nitro RTR, w/flag body (ready-to-run)RC8RS “Race Spec” Nitro Buggy RTR (ready-to-run)RC8.2 FT Nitro Buggy KitRC8.2e FT Electric Buggy KitRC8T Championship EditionSC8.2e Short Course Race Truck Rockstar/Makita RTR (ready-to-run)SC8.2e Short Course Race Truck Slick Mist RTR (ready-to-run)
** Use part number plus the desired size when ordering!
44:: Tools
:: Contact Information
11111112144914501541154215431544154515461547154815511553155415611562156315641565156715891590159216551656165716581659166016611662166316641665166616671668166916701671167216731674
171917373718371937203987642969567494770991107
11111111111111111111111111111111111111111111
111212121111121
FT Turnbuckle WrenchFT 4mm Turnbuckle Wrench (4x4 only)Offroad Ride Height GaugeFT Ride Height GaugeFT Hex Driver Set, (7 pcs)FT .050” Silver Hex DriverFT 1/16” Black Hex DriverFT 1.5mm Purple Hex DriverFT 5/64” Blue Hex DriverFT 3/32” Gold Hex DriverFT 2.5mm Green Hex DriverFT 3mm Red Hex DriverFT Screwdriver SetFT Phillips Silver ScrewdriverFT Silver Spring Hook Tool FT Nut Driver Set, (6 pcs)FT 3/16” Black Nut DriverFT 1/4” Red Nut DriverFT 5.5mm Red Nut DriverFT 11/32” Green Nut DriverFT 8mm Gold Nut DriverFT 5/64” Blue Ball Hex DriverFT 3/32” Gold Ball Hex DriverFT Ball Hex Driver Set, (3 pcs)FT 8-Piece 1/4” Hex Drive SetFT 1/4” Hex Drive Handle, without tipsFT 1/4” Hex Drive .050” TipFT 1/4” Hex Drive 1/16” TipFT 1/4” Hex Drive 5/64” - 2.0mm TipFT 1/4” Hex Drive 3/32” TipFT 1/4” Hex Drive 1.5mm TipFT 1/4” Hex Drive 2.5mm TipFT 1/4” Hex Drive 3/16” Nut Driver TipFT 1/4” Hex Drive 1/4” Nut Driver TipFT 1/4” Hex Drive 11/32” Nut Driver TipFT 1/4” Hex Drive 5.5mm Nut Driver TipFT 1/4” Hex Drive 7.0mm Nut Driver TipFT 1/4” Hex Drive 8.0mm Nut Driver TipFT 1/4” Hex Drive 5/64” - 2.0mm Ball End TipFT 1/4” Hex Drive 3/32” Ball End TipFT 1/4” Hex Drive Standard Screwdriver TipFT 1/4” Hex Drive Phillips Screwdriver TipFT 1/4” Hex Drive 2.5mm Ball End TipFT 1/4” 5 Piece Power Tool Tips Set (5/64-2.0mm, 1.5mm, 2.5mm, 5/64”- 2.0mm ball, 2.5mm ball)FT Camber + Track Width ToolFT Body Scissors12 Inch Nylon Wire Ties6 Inch Nylon Wire Ties8 Inch Nylon Wire TiesFT Droop GaugeShock Building ToolMolded Tools, SetV2 Stamped Multi Tool4 Inch Nylon Wire Ties13mm Shock Tools
Associated Electrics, Inc.26021 Commercentre Drive
Lake Forest, CA 92630-8853 USAhttp://www.TeamAssociated.com
http://www.RC10.comhttp://twitter/Team Associated
http://bit.ly/AEonFacebook
call: (949) 544-7500fax: (949) 544-7501
Check out the following web sites for all of our electric kits, current products, new releases,
setup help, tips, and racing info!
www.TeamAssociated.com. - www.RC10.com
:: RePlay CamerasRP001RP002RP021RP022RP023RP029RP030RP032RP033RP034RP036RP037RP038RP041RP042RP043RP044RP045RP046RP047RP048RP049
1111111111111111111111
Replay XD1080 Complete Camera SystemReplay XD720 Complete Camera SystemReplay XD1080 Lens Bezel KitReplay XD1080 Clear Lens CoverReplay XD1080 Lens Bezel & Rear Cap O-RingReplay XD1080 HDMI to Mini-HDMIReplay XD1080 Mini 8-pin USB Charge Data CableUSB DC Car Charger 1A StubbyUSB DC Car Charger 500mAhMicro SDHC USB Reader3M VHB 4991 Mount Adhesive for SnapTray3M VHB 5962 Mount Adhesive for Pro Flat Mount3M VHB 5962 Mount Adhesive for SnapTrayReplay XD Suction Cup Arm Mini ClampReplay XD Suction Cup Short Arm BaseReplay XD Skateboard MountReplay XD VHB SnapTray, ConvexReplay XD VHB SnapTray, FlatAu Plug for Universal DC Wall ChargerEu Plug for Universal DC Wall Charger Uk Plug for Universal DC Wall ChargerUniversal USB DC Wall Charger 1A
45:: Notes
46:: Notes
21
142536
332
1
B A
O I
Driver: Date: Track: Event:Conditions: Rev.1
Chassis Braces / Wheel Hex
Drivetrain
Chassis Weight Rear Hubs
Gearing
Differentials
Tires
Race and Vehicle Comments
Radio / Servos
Track Info
Rear Suspension
Wheelbase:
LongMediumShort
Anti Roll Bar:
2.2mm Black2.5mm Silver2.8mm Gold3.0mm Black
Anti Roll Bar:
2.2mm Black2.5mm Silver2.8mm Gold3.0mm Black
Spring: Shock Cap:Shock Fluid: Length:Piston: Rebound:
Dogbone:
CVA:
Weight:
Spring: Shock Cap:Shock Fluid: Length:Piston: Rebound:
Tire (F/R): /Compound (F/R): /Inserts (F/R): / Wheel (F/R): /Notes:
Qualify: Main: Finish: TQ:Comments:
Traction: High Medium Low
Surface: Smooth Bumpy Blue GrooveSoft Dirt Grass Clay WetAstroturf Dusty Other:
Ride Height: Ride Height:
Camber:
Rear Hubs:
StandardCNC FT Alum.
Chassis Braces: Wheel Hex:Pivot NarrowMolded WideAluminum
BumpsteerWashers:
Camber:
Caster:
Toe:
Front Shocks Rear Shocks
Setup SheetFront Suspension
:: For more setups, visit RC10.com and click on “Setup Sheets”
O
B A C
I
Hub:UpperLower
B-Plate Type
Low Original
Kickup BushingA-Plate
#Up Down
Squat BushingC-Plate
#Up Down
Toe BushingD-Plate
#In Out
Upper Hinge Pin Bushing
Front #Up Down
Rear #Up Down
Motor / ESC / BatteriesSpur Gear:
Pinion:
Front Diff Fluid:Center Diff Fluid:Rear Diff Fluid:Notes:
Motor & Wind: ESC:ESC Setting:Batteries:
Radio:Steering Servo: Steering Expo:Brake Expo:Initial Brake: Drag Brake:Dual Rate:
Steering System:
Stock RackSwing RackBellcrank Rack
backmidfront
RC8.2e RTR Setup
5,000
5,0005,000
2 dot
2 dot
1 dot
3 degree
-2
0
0
-1
16 deg
29mm29mm
Front Silver 3.9
46T - Plastic
17T
Alum.102mm 120mmNone None
Alum.Rear Silver 3.330 weight
16mm 16mm30 weight
2 dot
48
3x8mm (25201)
3x10mm (25202)
3x12mm (25203)
3x14mm (89208)
3x16mm (89224)
3x18mm (89209)
3x20mm (89210)
3x22mm (89455)
3x26mm (89211)
4x6mm (89213)
4x12mm (89214)
4x14mm (89217)
steering bearing (89161)
5x10mm (25237)
6x10mm (31404)
8x16mm (25236)
15x21mm (89162)
2.5x8mm (89222)
3x8mm (89223)
3x10mm (25620)
3x12mm (89454)
3x16mm (89224)
3x18mm (25191)
3x20mm (25192)
3x22mm (89474)
3x24mm (89225)
3x26mm (89226)
3x28mm (89227)
3x40mm (89228)
3x45mm (89279)
3x50mm (89452)
2.5x3mm (89201)
2.5x6mm (31520)
3x6mm (31531)
3x10mm (25211)
3x12mm (89202)
3x14mm (25187)
3x16mm (89203)
3x18mm (2308)
3x20mm (25188)
3x24mm (89204)
3x26mm (89205)
3x35mm (89453)
4x10mm (89206)
4x12mm (89207)
:: Hardware - 1:1 Scale View
Cap Head (shcs)Flat Head (fhcs)
Ball Bearings
Button Head (bhcs)
3x3mm (25225)
3x5mm (89219)
3x10mm (4671)
4x5mm (25226)
4x12mm (89220)
5x4mm (89221)
Set Screws
Ballstud Washer (9630)
3x5.6mm Steel Washer (89528)
2.5mm Washer (89278)
3x8mm Thin Washer (89218)
Diff Washer (89120)
Diff Shim (89117)
Shims and Washers
21
142536
332
1
B A
O I
Driver: Date: Track: Event:Conditions: Rev.1
Chassis Braces / Wheel Hex
Drivetrain
Chassis Weight Rear Hubs
Gearing
Differentials
Tires
Race and Vehicle Comments
Radio / Servos
Track Info
Rear Suspension
Wheelbase:
LongMediumShort
Anti Roll Bar:
2.2mm Black2.5mm Silver2.8mm Gold3.0mm Black
Anti Roll Bar:
2.2mm Black2.5mm Silver2.8mm Gold3.0mm Black
Spring: Shock Cap:Shock Fluid: Length:Piston: Rebound:
Dogbone:
CVA:
Weight:
Spring: Shock Cap:Shock Fluid: Length:Piston: Rebound:
Tire (F/R): /Compound (F/R): /Inserts (F/R): / Wheel (F/R): /Notes:
Qualify: Main: Finish: TQ:Comments:
Traction: High Medium Low
Surface: Smooth Bumpy Blue GrooveSoft Dirt Grass Clay WetAstroturf Dusty Other:
Ride Height: Ride Height:
Camber:
Rear Hubs:
StandardCNC FT Alum.
Chassis Braces: Wheel Hex:Pivot NarrowMolded WideAluminum
BumpsteerWashers:
Camber:
Caster:
Toe:
Front Shocks Rear Shocks
Setup SheetFront Suspension
:: For more setups, visit RC10.com and click on “Setup Sheets”
O
B A C
I
Hub:UpperLower
B-Plate Type
Low Original
Kickup BushingA-Plate
#Up Down
Squat BushingC-Plate
#Up Down
Toe BushingD-Plate
#In Out
Upper Hinge Pin Bushing
Front #Up Down
Rear #Up Down
Motor / ESC / BatteriesSpur Gear:
Pinion:
Front Diff Fluid:Center Diff Fluid:Rear Diff Fluid:Notes:
Motor & Wind: ESC:ESC Setting:Batteries:
Radio:Steering Servo: Steering Expo:Brake Expo:Initial Brake: Drag Brake:Dual Rate:
Steering System:
Stock RackSwing RackBellcrank Rack
backmidfront
Associated Electrics, Inc.26021 Com
mercentre Dr.
Lake Forest, CA 92630 USAhttp://w
ww
.TeamAssociated.com
http://ww
w.RC10.com
http://twitter/Team
_Associatedhttp://bit.ly/AEonFacebook
call: (949) 544-7500 - fax: (949) 544-7501Check out the follow
ing web sites for all of our kits,
current products, new releases, setup help, tips, and racing info!
ww
w.Team
Associated.com. - w
ww
.RC10.com
top related