radiation effects on unsteady free convection heat and...
Post on 13-Jun-2020
4 Views
Preview:
TRANSCRIPT
135
CHAPTER 5
Radiation effects on Unsteady Free Convection Heat and Mass Transfer in a
Walters-B Viscoelastic flow past an Impulsively started Vertical plate with
Uniform Heat and Mass Flux.
Published in Mathematical Sciences International Research Journal
Vol. 2, Issue 1 with ISSN 2278-8697 Jan/Feb-2013
& Paper presented in the International conference INTERNATIONAL CONFERENCE ON
MATHEMATICS, STATISTICS & COMPUTER ENGINEERING, Sep 13-14, Vijayawada, A.P, India.
136
5.1. INTRODUCTION The flow of a viscous incompressible fluid past an impulsively started an infinite
horizontal plate, moving in its own plane was first studied by Stokes [1]. It is often called
Rayleigh’s problem in the literature. Such a flow past an impulsively started semi-infinite
horizontal plate was first presented by Stewartson [2]. Hall [3] considered the flow past
an impulsively started semi-infinite horizontal by finite-difference method of a mixed
explicit-implicit type. Following Stoke’s analysis, Soundalgekar [4], presented an exact
solution to the flow of a viscous fluid past an impulsively started infinite isothermal
vertical plate. The solution was derived by the Laplace transform technique and the
effects of heating or cooling of the plate on the flow field were discussed through
Grashof number. Soundalgekar and Patil [5] studied Stoke’s problem for an infinite
vertical plate with constant heat flux.
Free convection flow occurs frequently in the nature. It occurs not only due to the
temperature differences, but also due to the concentration differences or combination of
these two. For example, in atmospheric flows, there exists differences in 퐻 표
concentration and hence the flow is affected by such concentration differences. Flows in
bodies of water are driven through the comparable effects upon density, of temperature,
concentration of dissolved materials and suspended particulate matter. Many transport
process exist in nature and in industrial applications in which the simultaneous heat and
mass transfer occur as a result of combined buoyancy effects of discussion of chemical
species.
A few representative fields of interest in which combined heat and mass transfer
plays an important role are design of chemical processing equipment, formation and
dispersion of fog, distribution of temperature and moisture over agricultural fields and
groves of fruit trees, damage of crops due to freezing, food processing and cooling
137
towers. Cooling towers are the cheapest way to cool large quantities of water. They are
very common in industries, especially in power plants. The tower is packed with the
internal material, commonly with wooden slats. Hot water sprayed into the top of the
trickles down through wood, evaporating as it goes. Air enters the bottom of the tower
and rises up through the packing. In smaller towers, the air can be pumped with the fan;
in larger ones, it is often allowed to rise by natural convection. In this context,
Soundalgekar [6] extended his own problem of [4] to mass transfer effects.
Muthucumaraswamy and Ganesan [7] studied first order chemical reaction on the flow
past an impulsively started vertical plate with uniform heat and mass flux.
Soundalgekar [8] first studied mathematical investigations for such a fluid
considering the oscillatory two dimensional viscoelastic flow along an infinite
porous wall, showing that an increase in the Walters viscoelasticity parameter and the
frequency parameter reduces the phase of the skin-friction. Raptis and Takhar [9] studied
flat thermal convection boundary layers flow of Walters-B fluid using numerical
shooting quadrature. The study of the Walters-B (1962) viscoelastic model [10] was
developed to simulate the viscous fluids are possessing short memory elastic effects and
can simulate accurately in many complex polymeric fluids, biotechnological and tri-
biological fluids. The Walters-B viscoelastic model has been studied extensively in many
flow problems. Elbashbeshy [11] studied the heat and mass transfer along a vertical plate
under the combined buoyancy effects of thermal and species diffusion, in the presence of
magnetic field. Helmy [12] presented an unsteady two-dimensional laminar free
convection flow of an incompressible electrically conducting (Newtonian or polar) fluid
through a porous medium bounded by an infinite vertical plane surface of constant
temperature.
138
In the context of space technology and in the process involving high
temperatures. The effect of radiation are of vital importance in recent developments in
hypersonic flights, missile re-entry, rocket combustion chambers, power plants for inter
planetary flight and gas cooled nuclear reactors, have focused attention on thermal
radiation as a mode of energy transfer, and emphasize the need for improved
understanding of radiative transfer in these processes. The interaction of radiation with
laminar free convection heat transfer from a vertical plate was investigated by Cess [13]
for an absorbing, emitting fluid in the optically thick region, using the singular
perturbation technique.
Arpaci [14] considered a similar problem in both the optically thin and optically
thick regions and used the approximate integral technique and first order profiles to solve
the energy equation. Cheng and Ozisik [15] considered a related problem for an
absorbing, emitting and isotropically scattering fluid, and treated the radiation part of the
problem exactly with the normal mode expansion technique. Raptis [16] analyzed the
thermal radiation and free convection flow through a porous medium by using
perturbation technique. Hossain and Takhar [17] studied the radiation effects on mixed
convection along a vertical plate with uniform surface temperature using the Keller Box
finite difference method. In all these papers, the flow is considered to be steady. The
unsteady flow past a moving plate in the presence of free convection and radiation were
studied by Mansour [18].
Raptis and Perdikis [19] studied the effect of thermal radiation and free
convection flow past moving plate. Das et al [20] analyzed the radiation effects on the
flow past an impulsively started infinite isothermal vertical plate. Chamkha et al [21]
considered the effect of radiation on free convection flow past a semi-infinite vertical
plate with mass transfer. Rajagopal et al [22] obtained exact solutions for the combined
139
various hydro magnetic flow, heat and mass transfer phenomena in a conducting
viscoelastic Walters-B fluid percolating a porous regime adjacent to a stretching sheet
with heat generation, viscous dissipation and wall mass flux effects, by using confluent
hyper geometric functions for different thermal boundary conditions at the wall. Rath
and Bastia [23] used a perturbation method to analyze the steady flow and heat transfer
of Walters-B model viscoelastic liquid between two parallel uniformly porous disks
rotating about a common axis, showing that drag is enhanced with suction but reduced
with injection and that heat transfer rate is accentuated with a rise in wall suction or
injection.
More recently Beg at al [24] studied the effects of thermal radiation on
impulsively started vertical plate using network simulation method [NSM]. V. R. Prasad
et al [25] studied the radiation and mass transfer effects on two-dimensional flow past an
impulsively started isothermal vertical plate. It is observed that an increase in the value of
radiation parameter the velocity and temperature decreases accompanied by simultaneous
reductions in both momentum and thermal boundary layers and also the time taken to
reach the steady state increases when the radiation parameter increases. V. Ramachandra
Prasad et al [26] studied Transient radiative hydro-magnetic free convection flow past an
impulsively started vertical plate with uniform heat and mass flux.
The above studies did not consider combined viscoelastic momentum, heat and
mass transfer from a impulsively started vertical plate, either for the steady case or
unsteady case. Owing to the significance of this problem in chemical and medical
biotechnological processing (e.g. medical cream manufacture) we study the transient case
of such a flow in the present paper using the robust Walters-B viscoelastic rheological
material model. A Crank-Nicolson finite difference scheme is utilized to solve the
unsteady dimensionless, transformed velocity, thermal and concentration boundary layer
140
equations in the vicinity of the impulsively started vertical plate. Another motivation of the
study is to further investigate the observed high heat transfer performance commonly
attributed to extensional stresses in viscoelastic boundary layers.
5.2. MATHEMATICAL MODEL
An unsteady two-dimensional laminar natural convection radiative flow of a
viscoelastic fluid past an impulsively started semi-infinite vertical plate is considered.
The x-axis is taken along the plate in the upward direction and y-axis is taken normal to
it. The physical model is shown in fig.1.
Initially assumed that the plate and the fluid are at the same temperature 푇 and
concentration level퐶 everywhere in the fluid. At time 푡 > 0, the plate starts moving
impulsively in the vertical direction with constant velocity 푢 against the gravitational
field. Temperature of the plate and concentration level near the plate are raised to 푇 and
퐶 respectively and maintained constantly thereafter. It is assumed that the concentration
퐶 of the diffusing species in the mixture is very less in comparison to the other
chemical species, which are present and hence the Soret and Dufour effects are
negligible. It is also assumed that there is no chemical reaction between the diffusing
141
species and the fluid. Under the above assumptions, the governing boundary layer
equations with Boussinesq’s approximation are
휕푢휕푥 +
휕푢휕푦 = 0(5.2.1)
휕푢휕푡 + 푢
휕푢휕푥 + 푣
휕푢휕푦 = 푔훽(푇 − 푇 ) + 푔훽∗(퐶 − 퐶 ) + 휈
휕 푢휕푦 − 푘
휕 푢휕푦 휕푡 (5.2.2)
휕푇휕푡 + 푢
휕푇휕푥 + 푣
휕푇휕푦 = 훼
휕 푇휕푦 −
1휌푐
휕푞휕푦 (5.2.3)
휕퐶휕푡 + 푢
휕퐶휕푥 + 푣
휕퐶휕푦 = 퐷
휕 퐶휕푦 (5.2.4)
The initial and boundary conditions are:
푡 ≤ 0:푢 = 0,푣 = 0,푇 = 푇 ,퐶 = 퐶
푡 > 0:푢 = 푢 ,푣 = 0,휕푇휕푦 = −
푞 (푥)푘 ,
휕퐶 휕푦 = −
푞∗ (푥)퐷 푎푡푦 = 0
푢 = 0, 푇 = 푇 , 퐶 = 퐶 ,푎푡푥 = 0(5.2.5)
푢 → 0, 푇 → 푇 ,퐶 → 퐶 푎푠푦 → ∞
By using the Rosseland approximation the radiative heat flux 푞 is given by
푞 = −4휎3푘
휕푇휕푦 (5.2.6)
Where휎 is the Stefan-Boltzmann constant and 푘 is the mean absorption coefficient.
It should be noted that by using the Rosseland approximation, the present analysis is
limited to optically thick fluids. If temperature differences within the flow are
significantly small, then equation [5.2.6] can be linearised by expanding푇 into the
Taylor series about 푇 , which after, neglect higher order terms, takes the form:
푇 ≅ 4푇 푇 − 3푇 (5.2.7)
142
In view of equations [6] and [7], equation [3] reduces to:
휕푇휕푡 + 푢
휕푇휕푥 + 푣
휕푇휕푦 = 훼
휕 푇휕푦 +
16휎 푇3푘 휌푐
휕 푇휕푦 (5.2.8)
On introducing the following non-dimensional quantities:
푋 =푥푢휈 ,푌 =
푦푢휈 ,푡 =
푡 푢휈 ,푈 =
푢푢 , 푉 =
푣푢
Γ =k Gr
L ,퐹 =푘 푘
4휎 푇 , 퐺푟 =
푔훽푞 휈푘푢
; 퐺푟 =푔훽∗푞∗ 휈퐷푢
(5.2.9)
푇 =(푇 − 푇 )푞 휈푘푢
,퐶 =(퐶 − 퐶 )푞∗ 휈퐷푢
,푃푟 =휈훼 , 푆푐 =
휈퐷 , 휈 =
휇휌 ,
1푃푟 =
푘휇푐 .
Equations (5.2.1) – (5.2.4) with (5.2.9) are reduced to the following non-dimensional
form:
휕푈휕푋 +
휕푈휕푌 = 0(5.2.10)
휕푈휕푡 + 푈
휕푈휕푋 + 푉
휕푈휕푌 =
휕 푈휕푌 + 퐺푟. 푇 + 퐺푚.퐶 − Γ
∂ U∂Y ∂t (5.2.11)
휕푇휕푡
+ 푈휕푇휕푋
+ 푉휕푇휕푌
=1푃푟 1 +
43퐹
휕 푇휕푌
(5.2.12)
휕퐶휕푡 + 푈
휕퐶휕푋 + 푉
휕퐶휕푌 =
1푆푐
휕 퐶휕푦 (5.2.13)
The corresponding initial and boundary conditions are:
푡 ≤ 0 ∶ 푈 = 0,푉 = 0, 푇 = 0,퐶 = 0
푡 > 0:푈 = 1, 푉 = 0,휕푇휕푦 = −1,
휕퐶휕푦 = −1푎푡푌 = 0(5.2.14)
푈 = 0, 푇 = 0,퐶 = 0,푎푡푋 = 0
143
푈 → 0,푇 → 0,퐶 → 0푎푠푌 → ∞
L – is the length of the plate, 퐺푟 –the Grashof number , 푃푟–the Prandtl
number, 푆푐 - Schmidt number, 퐹- is the radiation parameter, 푁- is the buoyancy ratio
parameter, Γ- is the viscoelasticity parameter. Knowing the velocity, temperature, and
concentration fields, it is interesting to find the local skin-friction, Nusselt number and
Sherwood numbers are in the non-dimensional equation model, computed with the
following mathematical expressions.
휏 = 퐺푟 휕푈휕푌
(5.2.15)
푁푢 = −푋퐺푟 휕푇휕푌
푇(5.2.16)
푆ℎ = −푋퐺푟 휕퐶휕푌
퐶(5.2.17)
We note that the dimensionless model defined by equations (5.2.10) –(5.2.13) under
conditions (5.2.14) reduces to Newtonian flow in the case of vanishing viscoelasticity,
i.e. when Γ → ∞.
5.3. NUMERICAL TECHNIQUE:
In order to solve these unsteady, non-linear coupled equations (5.2.10) –(5.2.13)
under conditions (5.2.14) an implicit finite difference scheme of The Crank- Nicolson
type has been employed. The finite difference equations corresponding to equations
(5.2.10) –(5.2.13) are as follows.
푈 , −푈 , + 푈 , −푈 , + 푈 , −푈 , + 푈 , − 푈 ,
4∆푋
+ 푉 , − 푉 , + 푉 , −푉 ,
2∆푌= 0(5.3.1)
144
푈 , − 푈 ,
∆푡+ 푈 ,
푈 , − 푈 , + 푈 , − 푈 ,
2∆푋+푉 ,
푈 , −푈 , +푈 , − 푈 , 4∆푌
=
푈 , − 2푈 , + 푈 , + 푈 , − 2푈 , + 푈 ,
2(∆푌)
−Γ푈 , − 2푈 , + 푈 , +푈 , − 2푈 , + 푈 ,
2(∆푌) ∆푡+ 퐺푟.
푇 , + 푇 ,
2
+퐺푚.퐶 , + 퐶 ,
2 (5.3.2)
푇 , − 푇 , Δ푡 + 푈 ,
푇 , − 푇 , + 푇 , − 푇 ,
2Δ푋 +푉 ,푇 . − 푇 , + 푇 , 푇 ,
4∆푌
=1푃푟
1 +4
3퐹푇 , − 2푇 , + 푇 , + 푇 , − 2푇 , + 푇 ,
2(∆푌) (5.3.3)
퐶 , − 퐶 ,
∆푡+푈 ,
퐶 , − 퐶 , + 퐶 , − 퐶 ,
2∆푋+푉 ,
퐶 , − 퐶 , + 퐶 , − 퐶 ,
4∆푌=
퐶 , − 2퐶 , + 퐶 , + 퐶 , − 2퐶 , + 퐶 ,
2푆푐(∆푌) (5.3.4)
The boundary condition at Y= 0 for the temperature in the finite difference form is
푇 , −푇 , + 푇 , −푇 ,
4.∆푌= −1(5.3.5)
At Y= 0 (i.e., j = 0), equation (5.3.3) becomes
푇 , − 푇 , Δ푡 + 푈 ,
푇 , − 푇 , + 푇 , − 푇 ,
2Δ푋
+푉 ,푇 , − 푇 , + 푇 , − 푇 ,
4∆푌
145
=1푃푟 1 +
43퐹
푇 , − 2푇 , + 푇 , + 푇 , − 2푇 , + 푇 ,
2(∆푌) (5.3.6)
After eliminating 푇 + 푇 , by using the equation (5.3.5), equation (5.3.6) reduces
to the following form
푇 , − 푇 , Δ푡 + 푈 ,
푇 , − 푇 , + 푇 , − 푇 ,
2Δ푋 − 푉 ,
=1푃푟 1 +
43퐹
푇 , − 푇 . + 푇 , − 푇 , + 2∆푌(∆푌) (5.3.7)
The boundary conditions at 푌 = 0 for the concentration in the finite difference form is
퐶 , − 퐶 , + 퐶 , − 퐶 ,
4∆푌 = −1(5.3.8)
At 푌 = 0 (i.e., j= 0), equation (5.3.4) becomes
퐶 , − 퐶 ,
∆푡+ 푈 ,
퐶 , − 퐶 , + 퐶 , − 퐶 ,
2∆푋+푉 ,
퐶 , − 퐶 , + 퐶 , − 퐶 ,
4∆푌=
퐶 , − 2퐶 , + 퐶 , + 퐶 , − 2퐶 , + 퐶 ,
푆푐(∆푌) (5.3.9)
After eliminating 퐶 , + 퐶 , by using the equations (5.3.8), equation (5.3.9)
reduces to the following +form
퐶 , − 퐶 ,
∆푡 + 푈 ,퐶 , − 퐶 , + 퐶 , − 퐶 ,
2∆푋 −푉 ,
= 1푆푐
퐶 , − 퐶 , + 퐶 , − 퐶 , + 2∆푌(∆푌) (5.3.10)
The region of integration is considered as a rectangle with sides 푋 (1)and
푌 (= 14) where 푌 corresponds to 푌 = ∞, which lies very well outside the
146
momentum, energy and concentration boundary layers. The grid system is shown in the
following figure.
After exercising some preliminary numerical experiment the mesh sizes have been
fixed as ∆푋 = 0.05, ∆푌 = 0.25 with the time step ∆푡 = 0.01. The computations are
executed initially, reducing the spatial mesh sizes by 50% in one direction, and later in
both directions by 50%. The results are compared. It is observed that in all cases, the
results differ in only fifth decimal places. Hence, the choice of mesh sizes is verified as
extremely efficient. During any one time step, the coefficients 푈 , and 푉 , appearing
in the difference equations are treated as constants. Here 푖designates the grid point
along the X- direction, j- along the Y-direction. The values of 퐶,푇,푈 and 푉 are known
at all grid points when 푡 = 0 from the initial conditions, the computations for 퐶,푇,푈
and 푉 at a time level (푛 + 1), using the values at previous time level (푛) are carried out
as follows.
The finite difference equations at every internal nodal point on a particular
푖 level constitutes a tridiagonal system of equations and is solved by using Thomas
algorithm. Thus the values of C are known at every nodal point at a particular
147
푖- level at (푛 + 1)th time level. In a similar way computations are carried out by moving
along 푖- direction. After computing values corresponding to each 푖 at a time level, the
values at the next time level are determined in a similar manner. Computations are
repeated until the steady state is reached. Here the steady state solution is assumed to
have reached when the absolute difference between the values of the velocity 푈 ,
temperature 푇, as well as the concentration 퐶 at two consecutive time steps are less
than 10 at all grid points. The scheme is unconditionally stable. Here the local
truncation error given by 푂(∆푡 + ∆푋 + ∆푌 ) and it tends to zero as ∆푡,
∆푋푎푛푑∆푌 tend to zero. It follows that the CNM scheme is compatible and stable
ensure the convergence.
5.4. RESULTS AND DISCUSSION
In order to check the accuracy of our numerical results, the present study is
compared with the available theoretical solution of Soundalgekar and Patil [4], and they
are found to be in good agreement. A representative set of numerical results is shown
graphically in figs.5.2(a)–5.7(c), to illustrate the influence of physical parameters, viz.
viscoelasticity parameter () = 0.005, thermal Grashof parameter (퐺푟) = 1.0, species
Grashof parameter (퐺푚) = 1.0, Schmidt number(푆푐) = 0.25 (oxygen diffusing in the
viscoelastic fluid), radiation parameter(퐹) = 0.5 and Prandtl number (푃푟) = 0.71 (water-
based solvents). All graphs therefore correspond to these values unless specifically
otherwise indicated. For the special case of 푆푐 = 1, the species diffuses at the same rate
as momentum in the viscoelastic fluid. Both concentration and boundary layer
thicknesses are the same for this case. For 푆푐 < 1, species diffusivity exceeds
momentum diffusivity, so that mass is diffused faster than momentum. The opposite case
applies when 푆푐 > 1. An increase in 푆푐will suppress concentration in the boundary
layer regime since higher 푆푐values will physically manifest in a decrease of molecular
148
diffusivity (퐷) of the viscoelastic fluid, i.e. a reduction in the rate of mass diffusion.
Lower 푆푐 values will exert the reverse influence since they correspond to higher
molecular diffusivities. Concentration boundary layer thickness is generally greater for
푆푐 < 1 than for 푆푐 > 1.
Figs. 5.2a to 5.2c we have presented the variation of velocity (푈), temperature
function (푇) and concentration (퐶) versus (푌) with on viscoelasticity () at 푋 = 1.0. An
increase in from 0 to 0.001, 0.003, 0.005 and the maximum value of 0.007, as depicted
in figure 5.2a, clearly enhances the velocity,푈 which ascends sharply and peaks in close
vicinity to the plate surface (푌 = 0). With increasing distance from the plate wall however
the velocity 푈 is adversely affected by increasing viscoelasticity, i.e. the flow is
decelerated. Therefore close to the plate surface the flow velocity is maximized for the
case of a Newtonian fluid (vanishing viscoelastic effect, i.e. =0) but this trend is reversed
as we progress further into the boundary layer regime. The switchover in behaviour
corresponds to approximately 푌 = 1. With increasing (푌) velocity profiles decay smoothly
to zero in the free stream at the edge of the boundary layer. The opposite effect is caused
by an increase in time. A rise in ‘푡’ from 4.310 through 4.370, 4.470, 4.530 to 4.940 causes
a decrease in flow velocity, 푈 nearer the wall in this case the maximum velocity arises for
the least time progressed. With more passage of time (푡 = 4.940) the flow is decelerated.
Again there is a reverse in the response at 푌~1, and thereafter velocity is maximized with
the greatest value of time. In figure 5.2(b), increasing viscoelasticity is seen to decrease
temperature throughout the boundary layer. All profiles decay from the maximum at the
wall to zero in the free stream. The graphs show therefore that increasing viscoelasticity
cools the flow. With progression of time, however the temperature, 푇 is consistently
enhanced, i.e. the fluid is heated as time progresses. A similar response is observed for the
concentration field, 퐶, in fig. 5.2(c). Increasing viscoelasticity again reduces concentration,
149
showing that species diffuses more effectively in Newtonian fluids (=0) than in strongly
viscoelastic fluids. Once again with greater elapse in time the concentration values are
reduced throughout the boundary layer regime (0 < 푌 < 14).
Figs. 5.3(a) to 5.3(c) depict the distributions of velocity (푈) and concentration (퐶)
versus coordinate (푌) for various Schmidt numbers (푆푐) and time (푡), close to the leading
edge at 푋 = 1.0, are shown. These figures again correspond to a viscoelasticity parameter
() = 0.005, i.e. weak elasticity and strongly viscous effects. An increase in푆푐 from 0.1
(low weight diffusing gas species) through 0.5 (oxygen diffusing) to 1.0 (denser
hydrocarbon derivatives as the diffusing species), 3.0 and 5.0, clearly strongly decelerates
the flow. In fig. 5.3(a), the maximum velocity arises at 푆푐 = 0.1 very close to the wall.
All profiles then descend smoothly to zero in the free stream. With higher Sc values the
gradient of velocity profiles is lesser prior to the peak velocity but greater after the peak.
An increase in time, t, is found to accelerate the flow. However with progression of time in
fig. 5.3(b), the temperature is found to be decreased in the boundary layer regime. Fig.
5.3(c), shows that a rise in 푆푐 strongly suppresses concentration levels in the boundary
layer regime.푆푐 defines the ratio of momentum diffusivity () to molecular diffusivity (퐷).
An increase in Schmidt number effectively depresses concentration values in the boundary
layer regime. Since higher 푆푐 values will physically manifest in a decrease of molecular
diffusivity (퐷) of the viscoelastic fluid, i.e. a reduction in the rate of mass diffusion. Lower
푆푐 values will exert the reverse influence since they correspond to higher molecular
diffusivities. Concentration boundary layer thickness is therefore considerably greater for
푆푐 = 0.1 than for 푆푐 = 5.0.
In Figs. 5.4(a) to 5.4(c) it is of great interest to show how the radiation-conduction
interaction effects on velocity, temperature and concentration. It is observed that, initially
150
for lower values of the radiation parameter 퐹, the heat transfer is dominated by conduction,
as the values of 퐹 increases the radiation absorption in boundary layer increases, i.e. an
increase in the radiation parameter 퐹 from 0.1 through 0.5, 1.0, 3.0, 5.0 and 10.0 results
in a decrease in the temperature and increase in concentration shown in figs.5.4(b) and
5.4(c).Here the velocity profiles increases initially and then slowly decreases to zero due to
viscoelasticity shown in fig. 5.4(a), i.e. when the radiation parameter 퐹 is increasing,
observed that the time progress initially increases and slowly decreases.
The effects of thermal Grashof number 퐺푟 are shown in Figs. 5.5(a) to 5.5(c) for
the velocity 푈, temperature 푇 , and species concentration 퐶 , distributions. figure 5.5(a)
indicates that an increasing 퐺푟from 0.1 through 1, 2, 4 to 6 strongly boosts velocity in
particular over the zone 0 < Y < 2. There is a rapid rise in the velocity near the wall
especially for the cases 퐺푟= 4 and 퐺푟 = 6. Peak value of 퐺푟 = 6 is about 푌~0.75 the
profiles generally descend smoothly towards zero although the rate of descend is greater
corresponding to higher thermal Grashof numbers. 퐺푟 defines the ratio of thermal
buoyancy force to the viscous hydrodynamic force and as expected does accelerate the
flow. Temperature distribution 푇 versus 푌 is plotted in figure 5.5b and is seen to decrease
with a rise in thermal Grashof number, results which agree with fundamental studies on
free convection (Schlichting boundary layer theory). Increasing 퐺푟 values figure 5.5c is
seen to considerably reduce concentration function values (퐶) throughout the boundary
layer.
The effects of species Grashof number 퐺푚 on velocity, temperature function and
concentration function are presented in figs. 5.6(a) to 5.6(c). Velocity, 푈, is observed to
increase considerably with rise in 퐺푚 from 0.1 to 6. Hence species Grashof number
boosts velocity of the fluid indicating that buoyancy as an accelerating effect on the flow
field. Temperature 푇, undergoes marked decrease in value however with a rise in species
151
Grashof number as illustrated in fig 7b. All temperatures descend from unity at the wall to
zero in the free stream. The depression in temperature is maximized by larger species
Grashof number in the vicinity 푌~2.1 , indicating a similar trend to the influence of
thermal Grashof number (figure 5.6b). Dimensionless concentration, 퐶as depicted in
figure 5.6c, is also seen to be reduced by increasing the species Grashof number. All
profiles decay smoothly from unity at the vertical surface to zero as 푦 ⟶ ∞ .
In figs. 5.7(a) to 5.7(c) the variation of dimensionless local skin friction (surface
shear stress), x, Nusselt number (surface heat transfer gradient), Nux and the Sherwood
number (surface concentration gradient), Shx, versus axial coordinate (푋 ) for various
viscoelasticity parameters () and time (푡) are illustrated. Shear stress is clearly enhanced
with increasing viscoelasticity, i.e. the flow is accelerated, a trend consistent with our
earlier computations in figure 5.6(a). The ascent in shear stress is very rapid from the
leading edge (푋 = 0) but more gradual as we progress along the plate surface away from
the plane. With an increase in time, t, shear stress, x, is however increased. Increasing
viscoelasticity () is observed in figure 5.7(b) to enhance local Nusselt number, Nux values
whereas they are again decreased with greater time. Similarly in figure 5.7(c), the local
Sherwood number Shx values are elevated with an increase in elastic effects, i.e. a rise in
from 0 (Newtonian flow) through 0.001, 0.003 to 0.005 but depressed finally in slightly
with time.
Table: It is observed that an increase in the radiation parameter 퐹 from 0.1 through
1.0, 10.0 and 100 results decrease in the temperature and increase in concentration, i.e. the
amount of heat transfer decreases (Nux), skin-friction increases gives shear stress in the
flow causes reduction in mass transfer rate observed.
152
5.5. CONCLUSION
A two-dimensional, unsteady laminar incompressible boundary layer model has
been presented for the external flow, heat and mass transfer in a Walters-B viscoelastic
buoyancy-driven radiative flow from an impulsively started vertical plate with uniform
heat and mass flux. The Walters-B viscoelastic model has been employed which is valid
for short memory polymeric fluids. The dimensionless conservation equations have been
solved with the well-tested, robust, highly efficient and implicit Crank-Nicolson finite
difference numerical method. The present computations have shown that increasing
viscoelasticity accelerates the velocity and enhances shear stress (local skin friction), local
Nusselt number and local Sherwood number, but reduces temperature and concentration in
the boundary layer. Here an increase of radiation, effects the amount of heat transfer
decreases (Nux), skin-friction increases gives shear stress in the flow causes reduction in
mass transfer rate observed. The temperature decreases with increase in 푃푟 or radiation
parameter 퐹 and also time required to reach steady state increases, when the radiation
parameter 퐹increases. This phenomenon is of interest in very high temperature (e.g. glass)
flows in the mechanical and chemical process industries and is currently under
investigation.
153
5.6. GRAPHS:
154
155
156
157
158
159
160
161
162
TABLE: 횪 = ퟎ.ퟎퟎퟓ, 퐒퐜 = ퟎ.ퟔ, 퐆퐫 = 퐆퐦 = ퟎ.ퟐ
Pr
F
X = 0.1 X = 0.5 X = 1.0
휏 푁푢 푆ℎ 휏 푁푢 푆ℎ 휏 푁푢 0.59805
0.71
0.1 3.34991 0.10941 0.18077 0.51558 0.55349 0.41042 0.01284 1.10697 0.59805
1.0 3.35116 0.07542 0.18075 0.51561 0.55348 0.41041 0.01284 1.10697 0.59804
10 3.35279 0.00432 0.18072 0.51560 0.55344 0.41041 0.01286 1.10696 0.59804
100 3.35315 -0.0132 0.18071 0.51568 0.55340 0.41040 0.01286 1.10696 0.59805
2.0
0.1 3.35033 0.10164 0.18076 0.51559 0.55348 0.41041 0.01284 1.10697 0.59804
1.0 3.35388 0.05071 0.18070 0.51571 0.55318 0.41040 0.01287 1.10696 0.59803
10 3.35724 0.00866 0.18065 0.51602 0.53870 0.41038 0.01291 1.10687 0.59803
100 3.35784 -0.0370 0.18064 0.51614 0.52943 0.41037 0.01292 1.10674 0.59804
7.0
0.1 3.35211 0.13625 0.18073 0.51564 0.55348 0.41041 0.01286 1.10697 0.59801
1.0 3.36016 0.00117 0.18060 0.51691 0.43854 0.41034 0.01301 1.10237 0.59796
100 3.36379 -0.4230 0.18054 0.52041 0.34453 0.41025 0.01389 0.93232 0.59805
REFERENCES
[1]. Stokes G.G (1995), the effect of internal friction of fluids on the motion of pendulums
Cambridge Phil. Trans., Vol. IX, pp. 8-106.
[2]. Stewartson. K (1951) on the impulsive motion of a flat plate in the viscous fluid.
Quarterly journal of Mechanics and Applied Mathematics, Vol.4, pp. 182-198.
[3]. Hall .M.G (1969), Boundary layer over an impulsively started flat plate, Proc. Yale.
Soc. London., Vol. 310A, pp.414.
[4]. Soundalgekar, V.M.,(1977) Convection effects on the Stoke’s problem for infinite
vertical plate ASME J. Heat Transfer, Vol.99, pp. 499-501.
163
[5]. Raptis. A, Singh. A. K (1985) free convection flow past an impulsively started
vertical plate in a porous medium by finite-difference method. Astrophy. and Space
Sci., Vol.112, pp. 259-265.
[6]. Soundalgekar, V.M., (1980) Effect of mass transfer and free convection on the
viscoelastic flow past an impulsively started vertical plate with constant heat flux,
Astro Physics, Vol. 70, pp. 179 -182.
[7]. Muthucumaraswamy. and Ganesan. P. (2001) studied the first order chemical reaction
on flow past an impulsively started vertical plate with uniform heat and mass flux
Acta. Mech., Vol. 147, pp. 45-47.
[8]. V.M.Soundalgekar, Ganesan and P. Puri, on fluctuating Flow of an elastic-viscous
fluid past an infinite plate with variable suction, J. Fluid Mechanics, 35,(1969), 3,
pp. 561- 573.
[9]. A. A .Raptis and H .S. Takhar studied flat thermal convection boundary layers flow
of a Walters-B fluid usig numerical shooting quadrature. Int. Comm. Heat and Mass
transfer, 16, (1989), 2, pp. 193-197.
[10]. K. Walters, Non-Newtonian effects in some elastic-viscous liquids whose behaviour
at small rates of shear is characterized by a general linear equations of state, Quart.
J. Mech. Applied Math, 15 (1962) 6. pp. 63 - 76.
[11]. Elbashbeshy. M. A. (1997) Heat and mass transfer along a vertical plate surface
tension and Concentration in the presence of magnetic field. Int. J. Engg. Sci., vol.
34(5), pp. 515-522.
[12]. Helmy. K. A. (1998), MHD unsteady free convection flow past a vertical porous
plate, AMM, Vol.78, pp. 255-270.
[13]. Cess R. D. The interaction of thermal radiation with free convection heat and mass
transfer. Int .J .of heat and mass transfer 9 (1966) pp 1269 - 1277.
164
[14]. Arpasi V.S. (1968), Effect of thermal radiation on the laminar free convection from a
heated vertical plate. Int. J. Heat and Mass transfer, Vol. 11, pp. 871-881.
[15]. Cheng and Ozisik. M. N(1972) radiation with free convection in an absorbing,
emitting and scattering medium. Int. J. Heat and Mass trans. Vol.15, pp. 1243-1252.
[16]. Raptis. A. (1998) Radiation and free convection flow through a porous medium,
Int.Commun. Heat and Mass transfer, Vol. 25, pp. 289-295.
[17]. Takhar [30] studied the radiation effects on mixed convection along a vertical plate
with uniform surface temperature Vol. 89 (2001), pp. 360-371.
[18]. Mansour. M. H. (1990) Radiative and free convection effects on the oscillatory flow
past a vertical plate. AstroPphysics and Space Science, Vol. 166, pp. 26-75.
[19]. Raptis .A. and Perdikis .C (1999), Radiation and free convection flow past a moving
plate. Appl. Mech. Engg. Vol. 4, pp. 817-821.
[20]. U .N. Das, R. Deka and V. M. Soundalgekar studied, the radiation effects on flow
past an impulsively started infinite vertical plate. J.of Theo.Appl. Fluid Mech, 1 (2)
(1996) 111-115.
[21]. Chamkha A. J., Takhar. H. S, analysed, the effects of radiation on free convection
flow past a semi-infinite vertical plate with mass transfer. Chem. Eng. J .Vol. 84
(2001), pp. 335-342.
[22]. K.Rajagopal, P.H.Veena and V.K. Pravin, Nonsimilar Solutions for heat and mass
transfer flow in an electrically conducting viscoelastic fluid over a stretching
sheet saturated in a porous medium with suction/blowing, J. Porous Media, 11, 2
(2008), pp. 219-230.
[23]. R.S. Rath and S. N. Bastia, Steady flow and heat transfer in a viscoelastic fluid
between two coaxial rotating disks, Proc. Mathematical Sciences, 87, 8 (1978), pp.
227- 236.
165
[24]. O. A. Beg, J. Zueco, T. A. Beg, H. S.Takhar, E. Kahya, NSM analysis of time –
dependent nonlinear buoyancy-driven double-diffusive radiative convection flow in
non-Darcy eological porous media, Acta Mechanica. 202 (2008), pp 181-204.
[25]. V. R. Prasad, N. Bhaskar Reddy and R. Muthucumaraswamy, Radiation and mass
transfer effects on two - dimensional flow past an impulsively started infinite vertical
plate, Int. J. Of Thermal Sciences, 46, 12 (2007), pp. 1251-1258.
[26]. V. Ramachandra Prasad, N.Bhaskar Reddy, R.Muthucumaraswamy studied the
transient radiative hydro-magnetic free convection flow past an impulsively started
vertical plate with uniform heat and mass flux. Theoretical Appl. Mech., Vol.33,
No.1, pp. 31(63), Belgrade 2006.
top related