put our bitumen - muser apac · 2019. 9. 11. · cleveland flash and fire point tester: cla 5...
Post on 22-Jan-2021
5 Views
Preview:
TRANSCRIPT
Dynamic Shear Rheometer:SmartPave 92
Fraass Breaking Point Tester: BPA 5
Standards:EN 12593JIS K 2207
Parameters:Fraass breaking point
The BPA 5 automatic Fraass breaking point tester determines the brittle behavior of bitumen and asphalt at low temperatures. A thin, flat steel plaque, coated with the sample, is flexed under specified conditions at a descending series of temperatures until a crack occurs.
Digital Ductility Meter:DDA 3
Standards:ASTM D113JIS K 2207AASHTO T51DIN 52013ASTM D6084EN 13398IP 516EN 13589EN 13703AASHTO T300
Parameters:Ductility (elongation)Elastic recoveryForce ductility
The DDA 3 automatic ductility meter provides 3 simultaneous test places to measure the ductility (elongation), elastic recovery, and force ductility of bitumen and asphalt.
Cleveland Flash and Fire Point Tester: CLA 5
Standards:ASTM D92ISO 2592JIS K 2265-4AASHTO T48FTM 791-1103, IP 36GOST 4333
Parameters:Flash pointFire point
The CLA 5 automatic open-cup flash and fire point tester measures the flash point, which describes the tendency to form a flammable mixture with air, and the fire point, which indicates the tendency for sustained burning, in bituminous materials.
Dynamic Shear Rheometer: SmartPave 102
Density Meter for Petroleum Products: DMA™ 4200 M
Softening Point Tester:RKA 5
Standards:ASTM D36EN 1427EN 13179-1JIS K 2207AASHTO T53
Parameters:Softening point
The RKA 5 ring-and-ball softening point tester with its laser-based detection system automatically determines the temperature at which a substance attains a particular degree of softness. It is ideal for samples without sharply defined melting points, which become softer and less viscous as the temperature rises.
Rotational Rheometer:RheolabQC
Standards:In correlation with ASTM D4402, AASHTO T316 and (DIN) EN 13302(Temperature control up to 180°C maximum)
Parameters:Rotational viscosityTemperatureShear rateShear stress
RheolabQC is a very robust and reliable instrument that measures the rotational viscosity of bitumen and asphalt products at elevated temperatures. The determination of flow curves and the temperature-dependent flow behavior of these materials gives you valuable information about their processability. A Peltier temperature device ensures fast and accurate heating up to 180 °C and disposable cups minimize the cleaning required.
Penetrometer:PNR 12
Standards:ASTM D5EN 1426EN 13179-2JIS K 2207
Parameters:Penetration
The modular PNR 12 penetrometer automatically measures the resistance a material provides against being pierced by a specifically shaped penetrator such as a needle. PNR 12 is suitable for consistency determination and provides the basic value for the product specification of bitumen and asphalt.
Standards:AASHTO T315, ASTM D7175 (SHRP-Test/Superpave PG)
AASHTO T316, ASTM D4402, DIN EN 13302 & 13702 (Rotational Viscosity)
AASHTO T350, ASTM D7405, DIN EN 16659 (MSCR-Test)
AASHTO TP101-UL (LAS-Test)
ASTM D7226 (Viscosity of Emulsified Asphalts)
FGSV AL 721 (Constant Shear Rate)
FGSV AL 722 (Temperature Sweep)
FGSV AL 723 (MSCR-Test)
FGSV AL BTSV (draft)
Parameters:Rotational viscosityComplex shear modulusPhase anglePerformance gradeElastic responseTemperatureNon-recoverable creep compliancePercentage recovery
SmartPave 102 is based on the well-established EC motor system from MCR rheometers and meets the highest measuring requirements, especially in research and development. It incorporates innovative features like Toolmaster™, a Peltier temperature device for dry sample heating, and step-by-step instructions for measuring procedures that take bitumen and asphalt binder rheology to previously unattained levels of accuracy.
SmartPave 92, also based on the well-established highly accurate EC motor system, is the ideal device for the daily measuring routines and quality control in test laboratories. The step-by-step software, Toolmaster™, TruRay (integrated light), QuickConnect (fast and easy mounting of the measuring system), and many other features guarantee excellent ease of use and convenient operation for bitumen and asphalt measurements.
Standards:AASHTO T315, ASTM D7175 (SHRP-Test/Superpave PG)
AASHTO T316, ASTM D4402, DIN EN 13302 & 13702 (Rotational Viscosity)
AASHTO T350, ASTM D7405, DIN EN 16659 (MSCR-Test)
ASTM D 7226 (Viscosity of Emulsified Asphalts)
FGSV AL 721 (Constant Shear Rate)
FGSV AL 722 (Temperature Sweep)
FGSV AL 723 (MSCR-Test)
FGSV AL BTSV (draft)
Parameters:Rotational viscosityComplex shear modulusPhase anglePerformance gradeElastic responseTemperatureNon-recoverable creep compliancePercentage recovery
Standards:In correlation with ASTM D70 and ASTM D3142
Parameters:Density 0.0002 g/cm3
API GravityRelative density
DMA™ 4200 M measures the density and specific gravity of highly viscous samples like bitumen and asphalt. Its U-tube made of Hastelloy C276 is highly resistant and virtually unbreakable. It improves, accelerates, and simplifies density measurement of bitumen and asphalt binders. Using DMA™ 4200 M makes tedious, manual, and time-intensive measurement with pycnometers or hydrometers a thing of the past.
Put our bitumen and asphalt measuring instruments to the test!
Register herefor your free demo:www.anton-paar.com/bitumen-asphalt
01 02 03 04 05 07 08 0906
36 Standards: AASHTO T48AASHTO T51AASHTO T53AASHTO T300AASHTO T301AASHTO T315 (SHARP-Test, Superpave PG)AASHTO T316 (Rotational viscosity)AASHTO T350 (MSCR-Test)AASHTO TP101-UL (LAS-Test)ASTM D5ASTM D36ASTM D92ASTM D113ASTM D4402 (Rotational viscosity)ASTM D6084ASTM D7175 (SHARP-Test, Superpave PG)ASTM D7405 (MSCR-Test)EN 1426EN 1427EN 12593EN 13179-1EN 13179-2EN 13302 (Rotational viscosity)EN 13398EN 13589EN 13702 (Rotational viscosity, CP)EN 13703EN 16659 (MSCR-Test)FTM 791-1103
Pave your way …
… to comprehensive asphalt measurement.
© 2
018
Ant
on P
aar
Gm
bH |
All
right
s re
serv
ed.
Spe
cific
atio
ns s
ubje
ct t
o ch
ange
with
out
notic
e.
Standards and Parameters
With Anton Paar’s portfolio of 9 instruments specifically developed for the bitumen and asphalt industry you can measure up to 21 parameters and comply with no less than 36 standards.
FGSV AL 721 (Constant Shear Rate)FGSV AL BTSV (draft)FGSV AL 722 (Temperature Sweep)FGSV AL 723 (MSCR-Test)ISO 2592JIS K 2207JIS K 2265-4
21 Parameters:
API gravityComplex shear modulusConsistencyDensityDuctilityElastic recoveryElastic responseFlash and fire pointForce ductilityFraass breaking pointNon-recoverable creep compliancePenetrationPercentage recoveryPerformance gradePhase angleRelative densityShear rateRotational viscosity Softening pointTemperatureShear stress
Production of asphalt/bitumen
Crude oil storage tanks
Furnaces
Furnaces
Atmospheric distillation
Vacuum distillation
Destillationbitumen
Oxidized bitumen
Transport andfurther processing
Blowing column
Polymer-modified bitumen
01 | 0203 | 0506 | 0708 | 09
04
01 | 0203
0304
0102
XPA
IP05
2EN
-A
top related